Onelink DC10-500 Smoke & CO Alarm Manual
Contents
1. Clean the Smoke CO Alarm at least once a month gently vacuum the outside of the Smoke CO Alarm using your household vacuum s soft brush attachment A can of clean compressed air sold at computer or office supply stores may also be used Follow manufacturer instructions for use Test the Smoke CO Alarm Never use water cleaners or solvents since they may damage the unit If the Smoke CO Alarm becomes contaminated by excessive dirt dust and or grime and cannot be cleaned to avoid unwanted alarms replace the unit immediately Relocate the unit if it sounds frequent unwanted alarms See Where This Alarm Should Not Be Installed for details IMPORTANT Actual battery service life depends on the Smoke CO Alarm and the environment in which it is installed Regardless of the manufacturer s suggested battery life you MUST replace the Alarm immediately once the unit starts chirping the low battery warning 13 Alarm End of Life Permanently Deactivating the Alarm After 10 years of operation or Low Battery warning deactivate the Alarm by following the diagram below Insert a tool below the edge shown and break tab Then slide activation switch to DEACTIVATE mode NOTE At end of life or low battery indication chirp unit must be put into deactivation mode to deactivate remaining stored energy in battery Unit will no longer function once put into this mode Unit will resist re mounting Once deactivate2. or on again off again CO problems can be caused by outdoor conditions and other special circumstances The following conditions can result in transient CO situations 1 Excessive spillage or reverse venting of fuel appliances caused by outdoor conditions such as Wind direction and or velocity including high gusty winds Heavy air in the vent pipes cold humid air with extended periods between cycles Negative pressure differential resulting from the use of exhaust fans Several appliances running at the same time competing for limited fresh air Vent pipe connections vibrating loose from clothes dryers furnaces or water heaters Obstructions in or unconventional vent pipe designs which can amplify the above situations 2 Extended operation of unvented fuel burning devices range oven fireplace 3 Temperature inversions which can trap exhaust close to the ground 4 Car idling in an open or closed attached garage or near a home These conditions are dangerous because they can trap exhaust in your home Since these conditions can come and go they are also hard to recreate during a CO investigation How Can I Protect My Family From CO Poisoning A CO Alarm is an excellent means of protection It monitors the air and sounds a loud alarm before Carbon Monoxide levels become threatening for average healthy adults A CO Alarm is not a substitute for proper maintenance of home appliances To help
3. Relocate your Alarm If frequent alarms continue have home rechecked for potential CO problems You may be experiencing an intermittent CO problem 26 Limited Warranty BRK Brands Inc BRK the maker of First Alert brand products warrants that for a period of ten years from the date of purchase this product will be free from defects in material and workmanship BRK at its option will repair or replace this product or any component of the product found to be defective during the warranty period Replacement will be made with a new or re manufactured product or component If the product is no longer available replacement may be made with a similar product of equal or greater value This is your exclusive warranty This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable Keep the original sales receipt Proof of purchase is required to obtain warranty performance BRK dealers service centers or retail stores selling BRK products do not have the right to alter modify or any way change the terms and conditions of this warranty This warranty does not cover normal wear of parts or damage resulting from any of the following negligent use or misuse of the product use on improper voltage or current use contrary to the operating instructions disassembly repair or alteration by anyone other than BRK or an authorized service center Further the warranty does not cover Acts o
4. accidentally damage or set fire to the unit or to your home NEVER use vehicle exhaust Exhaust may cause permanent damage and voids your warranty You can test this Smoke CO Alarm by pressing and holding the Test Silence button on the Alarm cover until Alarm Voice says Testing typically 3 5 seconds During testing you will see and hear the following sequence The Alarm Voice will say Testing Alarms The Alarm will sound and for your protection is very loud This may take a few seconds The LED chases Blue The Alarm Voice will say Testing Smoke The Horn will sound 3 beeps The LED chases and flashes Red The Alarm Voice will say Testing Carbon Monoxide The Horn will sound 4 beeps The LED chases and flashes Red Next The Alarm Voice will say Evacuate Evacuate there s a Fire in the Location example Kitchen The LED chases Red The Alarm Voice will say Highest carbon monoxide level was 0 PPM The LED chases Blue The Alarm Voice will then say The testing is complete The test is done and you are protected The LED glows Green If the unit does not alarm make sure it has been activated correctly and test again If the unit still does not alarm replace it immediately Regular Maintenance This unit has been designed to be as maintenance free as possible but there are a few simple things you must do to keep it working properly Test it at least once a week
5. Regulatory Information for CO Alarms What Levels of CO Cause an Alarm Underwriters Laboratories Inc Standard UL2034 requires residential CO Alarms to sound when exposed to levels of CO and exposure times as described below They are measured in parts per million ppm of CO over time in minutes UL2034 Required Alarm Points If the alarm is exposed to 400 ppm of CO IT MUST ALARM BETWEEN 4 amp 15 MINUTES If the alarm is exposed to 150 ppm of CO IT MUST ALARM BETWEEN 10 amp 50 MINUTES If the alarm is exposed to 70 ppm of CO IT MUST ALARM BETWEEN 60 amp 240 MINUTES Approximately 10 of COHb exposure at levels of 10 to 95 Relative Humidity RH This unit is designed not to alarm when exposed to a constant level of 30 ppm for 30 days IMPORTANT CO alarms are designed to alarm before there is an immediate life threat Since you cannot see or smell CO never assume it s not present An exposure to 100 ppm of CO for 20 minutes may not affect average healthy adults but after 4 hours the same level may cause headaches An exposure to 400 ppm of CO may cause headaches in average healthy adults after 35 minutes but can cause death after 2 hours Standards Underwriters Laboratories Inc Single and Multiple Station carbon monoxide alarms UL2034 According to Underwriters Laboratories Inc UL2034 Section 1 1 2 Carbon monoxide alarms covered by these requirements are intended to respond to the presenc
6. a Smoke Alarm in all rooms halls storage areas finished attics and basements where temperatures normally remain between 40 F 4 4 C and 100 F 37 8 C Make sure no door or other obstruction could keep smoke from reaching the Smoke Alarms For your information the National Fire Alarm and Signaling Code NFPA 72 reads as follows Required Detection Where required by applicable laws codes or standards for a specific type of occupancy approved single and multiple station smoke alarms shall be installed as follows In all sleeping rooms and guest rooms Outside of each separate dwelling unit sleeping area within 21 ft 6 4 m of any door to a sleeping room the distance measured along a path of travel On every level of a dwelling unit including basements On every level of a residential board and care occupancy small facility including basements and excluding crawl spaces and unfinished attics In the living area s of a guest suite In the living area s of a residential board and care occupancy IMPORTANT Specific requirements for Smoke Alarm installation vary from state to state and from region to region Check with your local Fire Department for current requirements in your area It is recommended AC or AC DC units be interconnected for added protection 19 Regulatory Information Federal Communications Commission FCC Compliance Statement NOTE This equipment has been tested and
7. prevent CO problems and reduce the risk of CO poisoning Clean chimneys and flues yearly Keep them free of debris leaves and nests for proper air flow Also have a professional check for rust and corrosion cracks or separations These conditions can prevent proper air movement and cause back drafting Never cap or cover a chimney in any way that would block air flow Test and maintain all fuel burning equipment annually Many local gas or oil companies and HVAC companies offer appliance inspections for a nominal fee Make regular visual inspections of all fuel burning appliances Check appliances for excessive rust and scaling Also check the flame on the burner and pilot lights The flame should be blue A yellow flame means fuel is not being burned completely and CO may be present Keep the blower door on the furnace closed Use vents or fans when they are available on all fuel burning appliances Make sure appliances are vented to the outside Do not grill or barbecue indoors or in garages or on screen porches Check for exhaust back flow from CO sources Check the draft hood on an operating furnace for a back draft Look for cracks on furnace heat exchangers Check the house or garage on the other side of shared wall Keep windows and doors open slightly If you suspect that CO is escaping into your home open a window or a door Opening windows and doors can significantly decrease CO levels 17
8. 10yr Sealed Battery Wi Fi Smoke Carbon Monoxide Alarm User s Manual Model DC10 500 Important Please read carefully and save this document This user s manual contains important information about your combination Smoke and CO Alarm s operation If you are installing this alarm for use by others you must leave this manual or a copy of it with the end user Installed on Replace by 2 Table of Contents Welcome 3 Parts of this Alarm 4 Understanding Your Alarm 5 Where to Install 6 7 Where Not to Install 8 Set Up and Installation 9 Wireless Interconnect 10 When the Alarm Sounds 10 11 Using the Silence Feature 11 Weekly Testing 12 Regular Maintenance 12 Alarm End of Life 13 Ionization and Photoelectric Technology 13 Fire Safety Tips 14 What You Need to Know About CO 15 Potential Sources of CO in the Home 16 Regulatory Information 17 19 Special Compliance 20 22 General Limitations 23 24 Troubleshooting Guide 25 Limited Warranty 26 Copyright and Technical Specifications 27 3 Welcome Thank you for choosing First Alert for your safety needs In addition to the alarm sounds you can receive notifications in case of an emergency to help provide a warning of a fire or carbon monoxide leak while you are home or away Please take time to read this manual and make this alarm an integral part of your family s safety plan Visit www fir
9. as as much as possible Within 5 feet 1 5 meters of any cooking appliance In air streams near kitchens Air currents can draw cooking smoke into the smoke sensor and cause unwanted alarms In extremely humid areas This Alarm should be at least 10 feet 3 meters from a shower sauna humidifier vaporizer dishwasher laundry room utility room or other source of high humidity In direct sunlight In turbulent air near ceiling fans or open windows Blowing air may prevent CO smoke from reaching the sensors In areas where temperature is colder than 40 F 4 4 C or hotter than 100 F 37 8 C These areas include non air conditioned crawl spaces unfinished attics uninsulated or poorly insulated ceilings porches and garages In insect infested areas Insects can clog the openings to sensing chamber Less than 12 inches 305 mm away from fluorescent lights Electrical noise can interfere with the sensor In dead air spaces See below for additional information Installing Smoke CO Alarms in Mobile Homes Dead air spaces may prevent smoke from reaching the Smoke CO Alarm To avoid dead air spaces follow installation recommendations below On ceilings install Smoke CO Alarms as close to the center of the ceiling as possible If this is not possible install the Smoke CO Alarm at least 4 inches 102 mm from the wall or corner For wall mounting if allowe
10. cause undesired operation RF Exposure Information This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment In order to avoid the possibility of exceeding the FCC radio frequency exposure limits human proximity to the antenna shall not be less than 20cm during normal operation 20 Industry Canada IC Compliance Statement ENGLISH This device complies with Industry Canada License exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Under Industry Canada regulations this radio transmitter may only operate using an antenna of a type and maximum or lesser gain approved for the transmitter by Industry Canada To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that necessary for successful communication FRENCH Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromet
11. d The average healthy adult might not feel any symptoms when the CO Alarm sounds However people with cardiac or respiratory problems infants unborn babies pregnant mothers or elderly people can be more quickly and severely affected by CO If you experience even mild symptoms of CO poisoning consult your doctor immediately Finding the Source of CO After an Alarm Carbon monoxide is an odorless invisible gas which often makes it difficult to locate the source of CO after an alarm These are a few of the factors that can make it difficult to locate sources of CO House well ventilated before the investigator arrives Problem caused by backdrafting Transient CO problem caused by special circumstances Because CO may dissipate by the time an investigator arrives it may be difficult to locate the source of CO BRK Brands Inc shall not be obligated to pay for any carbon monoxide investigation or service call 16 Potential Sources of CO in the Home Fuel Burning Appliances Like portable heater gas or wood burning fireplace gas kitchen range or cooktop gas clothes dryer Damaged or Insufficient Venting Corroded or disconnected water heater vent pipe leaking chimney pipe or flue or cracked heat exchanger blocked or clogged chimney opening Improper Use of Appliance Device Operating a barbecue grill or vehicle in an enclosed area like a garage or screened porch Transient CO Problems Transient
12. d replace Alarm immediately 2 SLIDE SWITCH 1 BREAK TAB Ionization amp Photoelectric Technology This alarm uses Photoelectric technology All First Alert Onelink Smoke Alarms conform to regulatory requirements including UL217 and are designed to detect particles of combustion Smoke particles of varying number and size are produced in all fires Ionization Technology Ionization technology is generally more sensitive than Photoelectric technology at detecting small particles which tend to be produced in greater amounts by flaming fires which consume combustible materials rapidly and spread quickly Sources of these fires may include paper burning in a wastebasket or a grease fire in the kitchen Photoelectric Technology Photoelectric technology is generally more sensitive than ionization technology at detecting large particles which tend to be produced in greater amounts by smoldering fires which may smolder for hours before bursting into flame Sources of these fires may include cigarettes burning in couches or bedding NOTE For maximum protection use both types of Smoke Alarms on each level and in every bedroom of your home 14 Fire Safety Tips Follow safety rules and prevent hazardous situations 1 Use smoking materials properly Never smoke in bed 2 Keep matches or lighters away from children 3 Store flammable materials in proper containers 4 Keep electrical appliances in good condition and d
13. d by building codes the top edge of Smoke CO Alarms should be placed between 4 inches 102 mm and 12 inches 305 mm from the wall ceiling line below typical dead air spaces On a peaked gabled or cathedral ceiling install first Smoke CO Alarm within 3 feet 0 9 meters of the peak of the ceiling measured horizontally Additional Smoke CO Alarms may be required depending on the length angle etc of the ceiling s slope Refer to NFPA 72 for details on requirements for sloped or peaked ceilings 9 Set Up amp Installation Do not install this unit over an electrical junction box Air currents around junction boxes can prevent smoke from reaching the sensing chamber and prevent the unit from alarming Only AC powered units are intended for installation over junction boxes NOTE Be sure to mount the product in the orientation specified in the next steps as this provides the most stability for mounting the product to the wall or ceiling When wall mounting it is suggested that the horn opening is in the upper left corner This alarm is designed to be mounted on the ceiling or wall if necessary Ensure the iOS software is updated to iOS 9 Step 1 Download the free Onelink app from the App Store and follow set up instructions Step 2 Hold the mounting bracket against the ceiling or wall so the two universal mounting holes are aligned approximately at the 9 and 3 o clock positions See image Trace around the holes
14. ds Highest carbon monoxide level was 0 PPM Emergency Highest carbon monoxide level was Number PPM Testing Testing Smoke beep beep beep Testing Carbon Monoxide beep beep beep beep Evacuate Evacuate there s Fire in the Location Emergency Warning Evacuate There is Smoke or Carbon Monoxide in the Location Evacuate Malfunction Detector error Please see manual or call customer service 6 Where to Install Minimum coverage for Smoke Alarms as recommended by the National Fire Protection Association NFPA is one Smoke Alarm on every floor in every sleeping area and in every bedroom See Regulatory Information For Smoke Alarms for details on the NFPA recommendations For CO Alarms the National Fire Protection Association NFPA recommends that a CO Alarm should be centrally located outside of each separate sleeping area in the immediate vicinity of the bedrooms For added protection install additional CO Alarms in each separate bedroom and on every level of your home NOTE For added protection install an additional Smoke CO Alarm at least 15 feet 4 6 meters away from the furnace or fuel burning heat source where possible In smaller homes or in manufactured homes where this distance cannot be maintained install the Alarm as far away as possible from the furnace or other fuel burning source Installing the Alarm closer than 15 feet 4 6 meters will
15. e immediately What To Do In Case of a Fire Don t panic stay clam Follow your family escape plan Get out of the house as quickly as possible Don t stop to get dressed or collect anything Feel doors with the back of your hand before opening them If a door is cool open it slowly Don t open a hot door Keep doors and windows closed unless you must escape through them Cover your nose and mouth with a cloth preferably damp Take short shallow breaths Meet at your planned meeting place outside your home and do a head count to make sure everybody got out safely Call the Fire Department as soon as possible from outside Give your address then your name Never go back inside a burning building for any reason Contact your Fire Department for ideas on making your home safer 11 When the Alarm Sounds Continued What To Do If The CO Alarm Sounds 1 Press the Test Silence button On App or on unit 2 Call your emergency services fire department or 911 3 Immediately move to fresh air outdoors or by an open door or window Do a head count to check that all persons are accounted for Do not re enter the premises or move away from the open door or window until the emergency services responder has arrived the premises have been aired out and your CO Alarm remains in its normal condition 4 After following steps 1 3 if your CO Alarm reactivates within a 24 hour period repea
16. e of carbon monoxide from sources such as but not limited to exhaust from internal combustion engines abnormal operation of fuel fired appliances and fireplaces CO Alarms are intended to alarm at carbon monoxide levels below those that could cause a loss of ability to react to the dangers of Carbon Monoxide exposure This CO Alarm monitors the air at the Alarm and is designed to alarm before CO levels become life threatening This allows you precious time to leave the house and correct the problem This is only possible if Alarms are located installed and maintained as described in this manual Gas Detection at Typical Temperature and Humidity Ranges The CO Alarm is not formulated to detect CO levels below 30 ppm typically UL tested for false alarm resistance to Methane 500 ppm Butane 300 ppm Heptane 500 ppm Ethyl Acetate 200 ppm Isopropyl Alcohol 200 ppm and Carbon Dioxide 5000 ppm Values measure gas and vapor concentrations in parts per million Audible Alarm 85 dB minimum at 10 feet 3 meters 18 Regulatory Information for Smoke Alarms Installing Smoke Alarms in Single Family Residences The National Fire Protection Association NFPA recommends one Smoke Alarm on every floor in every sleeping area and in every bedroom In new construction the Smoke Alarms must be AC powered and interconnected See Agency Placement Recommendations for details For additional coverage it is recommended that you install
17. f God such as fire flood hurricanes and tornadoes or any batteries that are included with this unit BRK shall not be liable for any incidental or consequential damages caused by the breach of any express or implied warranty Except to the extent prohibited by applicable law any implied warranty of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty Some states provinces or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state or province to province How to Obtain Warranty Service Service If service is required do not return the product to your retailer In order to obtain warranty service contact the Consumer Affairs Division at onelinksupport jardensafety com or 1 800 323 9005 To assist us in serving you please have the model number and date of purchase available when calling For Warranty Service return to 1301 Joe Battle El Paso TX 79936 Disposal Waste electrical products should not be disposed of with regular household waste Please recycle where facilities exist Check local requirements for disposal of Lithium powered electronic devices The Alarm should be deactivated before disposal See page 13 Permanentl
18. found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may
19. fter the Test Silence button is released the Red LED stops during the silence mode Silence the End of Life Signal This silence feature can temporarily quiet the End of Life warning chirp for up to 2 days You can silence the End of Life warning chirp by pressing the Test Silence button or via the Onelink app The horn will chirp acknowledging that the End of Life silence feature has been activated After approximately 2 days the End of Life chirp will resume WARNING Never deactivate the unit to quiet an unwanted alarm Deactivating the alarm disables the unit and removes your protection When the Smoke Alarm is Silenced When the CO Alarm is Silenced The Smoke Alarm will remain silent for up to 15 minutes then return to normal operation The CO Alarm will remain silent for up to 4 minutes If the smoke has not cleared or continues to increase the device will go back into alarm After 4 minutes if CO levels remain potentially dangerous the horn will start sounding again 12 Weekly Testing CAUTION It is important to test this unit every week to make sure it is working properly Using the test button is the recommended way to test this Smoke CO Alarm WARNING DO NOT stand close to the Alarm when the horn is sounding Exposure at close range may be harmful to your hearing When testing step away when horn starts sounding WARNING NEVER use an open flame of any kind to test this unit You might
20. fuels include Wood coal charcoal oil natural gas gasoline kerosene and propane Common appliances are often sources of CO If they are not properly maintained are improperly ventilated or malfunction CO levels can rise quickly CO is a real danger now that homes are more energy efficient Air tight homes with added insulation sealed windows and other weatherproofing can trap CO inside Symptoms of CO Poisoning These symptoms are related to CO POISONING and should be discussed with ALL household members Mild Exposure Slight headache nausea vomiting fatigue flu like symptoms Medium Exposure Throbbing headache drowsiness confusion fast heart rate Extreme Exposure Convulsions unconsciousness heart and lung failure Exposure to Carbon Monoxide can cause brain damage death IMPORTANT This CO Alarm measures exposure to CO over time It alarms if CO levels are extremely high in a short period of time or if CO levels reach a certain minimum over a long period of time The CO Alarm generally sounds an alarm before the onset of symptoms in average healthy adults Why is this important Because you need to be warned of a potential CO problem while you can still react in time In many reported cases of CO exposure victims may be aware that they are not feeling well but become disoriented and can no longer react well enough to exit the building or get help Also young children and pets may be the first affecte
21. g codes Refer to NFPA 72 National Fire Alarm and Signaling Code and NFPA 101 Life Safety Code local building codes or consult your Fire Department for detailed fire protection requirements in buildings not defined as households HUD MAP Program Certain HUD battery powered Smoke Alarm applications especially those that fall under HUD 223 f MAP Multi family Accelerated Processing may require a 10 Year sealed tamper resistant battery This alarm meets that requirement 23 General Limitations for Smoke CO Alarms This Smoke CO Alarm is intended for residential use It is not intended for use in industrial applications where Occupational Safety and Health Administration OSHA requirements for Carbon Monoxide Alarms must be met The Smoke Alarm portion of this device is not intended to alert hearing impaired residents Special purpose Smoke Alarms should be installed for hearing impaired residents CO Alarms are not yet available for the hearing impaired Smoke CO Alarms may not waken all individuals Practice the escape plan at least twice a year making sure that everyone is involved from kids to grandparents Allow children to master fire escape planning and practice before holding a fire drill at night when they are sleeping If children or others do not readily waken to the sound of the Smoke CO Alarm or if there are infants or family members with mobility limitations make sure that someone is assigned to assist them in fire d
22. m sounds they all will sound WARNING Install alarms and test to assure range and reliability of interconnection throughout the house First Alert Onelink alarms can typically communicate with each other if they re 50ft 15m apart inside a home Keep in mind that some features of a home may reduce the interconnect range and reliability of interconnection including the number of floors number size of rooms furniture type of building material suspended ceilings ductwork large metallic appliances and metal studs This kind of interference may be fixed by adding more Onelink alarms that can route wireless signals around any various obstructions Make sure you test your Onelink alarms for proper interconnection via the weekly testing Wi Fi Frequency This alarm supports wireless frequency of 2 4Ghz b g n For best results recommended to use with a 802 11 b g n router Adding Additional Alarms Simply follow the instructions on your Onelink app to add additional alarms to your account Identification of Events If your alarm sounds it is important to first identify the type of alarm When the Alarm Sounds What To Do If The Smoke Alarm Sounds If the unit alarms and you are not testing the unit it is warning you of a potentially dangerous situation that requires your immediate attention NEVER ignore any alarm Ignoring the alarm may result in injury or death If the unit alarms then get everyone out of the hous
23. moke or CO in the basement For this reason one alarm device may not give adequate early warning Recommended minimum protection is one alarm device in every sleeping area every bedroom and on every level of your home Some experts recommend battery powered Smoke and CO Alarms be used in conjunction with interconnected AC powered Smoke Alarms For details see About Smoke Alarms for details Smoke CO Alarms may not be heard The alarm horn loudness meets or exceeds current UL standards of 85 dB at 10 feet 3 meters However if the Smoke CO Alarm is installed outside the bedroom it may not wake up a sound sleeper or one who has recently used drugs or has been drinking alcoholic beverages This is especially true if the door is closed or only partly open Even persons who are awake may not hear the alarm horn if the sound is blocked by distance or closed doors Noise from traffic stereo radio television air conditioner or other appliances may also prevent alert persons from hearing the alarm horn This Smoke CO Alarm is not intended for people who are hearing impaired The Alarm may not have time to alarm before the fire itself causes damage injury or death since smoke from some fires may not reach the unit immediately Examples of this include persons smoking in bed children playing with matches or fires caused by violent explosions resulting from escaping gas This Smoke CO Alarm is not a substitute for life insurance Though this Sm
24. not harm the Alarm but may increase the frequency of unwanted alarms In general install combination Smoke and Carbon Monoxide Alarms On every level of your home including finished attics and basements Inside every bedroom especially if people sleep with the door partly or completely closed In the hall near every sleeping area If your home has multiple sleeping areas install a unit in each If a hall is more than 40 feet 12 meters long install a unit at each end At the top of first to second floor stairs At the bottom of the basement stairs For additional coverage install Alarms in all rooms halls and storage areas where temperatures normally remain between 40 F and 100 F 4 4 C and 37 8 C Recommended Placement When installing on the wall the top edge of Smoke Alarms should be placed between 4 inches 102 mm and 6 inches 153 mm from the wall ceiling line When installing on the ceiling place the alarm as close to the center as possible In either case install at least 4 inches 102 mm from where the wall and ceiling meet See Avoiding Dead Air Spaces for more information NOTE For any location make sure no door or other obstruction could keep carbon monoxide or smoke from reaching the Alarm Installing Smoke CO Alarms in Mobile Homes For minimum security install one Smoke CO Alarm as close to each sleeping area as possible For more
25. ns are no longer considered valid and the FCC ID and IC Certification Number cannot be used on the final product In these circumstances the OEM integrator will be responsible for re evaluating the end product including the transmitter and obtaining a separate FCC and Industry Canada authorization End Product Labeling The BLEMOD1 Module and AW CU300 Module are labeled with their own FCC ID and IC Certification Number If the FCC ID and IC Certification Numbers are not visible when the module is installed inside another device then the outside of the device into which the module is installed must also display a label referring to the enclosed module In that case the final end product must be labeled in a visible area with the following Contains Transmitter Modules FCC ID M7U BT1IOT and FCC ID TLZ CU300 Contains Transmitter Modules IC 10190A BT1IOT and IC 6100A CU300 Or Contains FCC ID M7U BT1IOT and FCC ID TLZ CU300 Contains IC 10190A BT1IOT and IC 6100A CU300 The OEM of the BLEMOD1 Module and AW CU300 Module must only use the approved antenna s listed above which have been certified with this module The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product To comply with FCC and Industry Canada RF radiation exposure limits for general population the antenna
26. oke CO Alarm warns against increasing CO levels or the presence of smoke BRK Brands Inc does not warrant or imply in any way that they will protect lives Homeowners and renters must still insure their lives This Smoke CO Alarm has a limited life Although this Smoke CO Alarm and all of its parts have passed many stringent tests and are designed to be as reliable as possible any of these parts could fail at any time Therefore you must test this device weekly The unit should be replaced immediately if it is not operating properly This Smoke CO Alarm is not foolproof Like all other electronic devices this Smoke CO Alarm has limitations It can only detect smoke or CO that reaches the sensors It may not give early warning of the source of smoke or CO is in a remote part of the home away from the alarm device 25 Troubleshooting Guide Smoke Alarm ONLY Smoke Alarm sounds when no smoke is visible Unwanted alarm may be caused by non emergency source like cooking smoke Silence alarm on App or using unit button clean the alarm s cover with a soft clean cloth If frequent unwanted alarms continue relocate your alarm Alarm may be too close to kitchen cooking appliance or steamy bathroom If you have questions that cannot be answered by reading this manual contact Consumer Affairs at onelinksupport jardensafety com or 1 800 323 9005 Alarm FAQ If the Alarm Problem You Should Light flashes yellow and Horn
27. on t overload electrical circuits 5 Keep stoves barbecue grills fireplaces and chimneys grease free and debris free 6 Never leave anything cooking on the stove unattended 7 Keep portable heaters and open flames like candles away from flammable materials 8 Don t let rubbish accumulate Basic Safety Information Keep alarms clean and test them weekly Replace alarms immediately if they are not working properly Smoke alarms that do not work cannot alert you to a fire Keep at least one working fire extinguisher on every floor and an additional one in the kitchen Have fire escape ladders or other reliable means of escape from an upper floor in case stairs are blocked WARNING This unit will not operate without battery power The Smoke CO Alarm cannot work until you activate the battery power pack NEVER ignore any alarm See What To Do If Your Smoke Co Alarm Sounds on page 10 for more information on how to respond to an alarm Failure to respond can result in injury or death The Silence Features are for your convenience only and will not correct a problem See Using the Silence Feature on page 11 for details Always check your home for a potential problem after any alarm Failure to do so can result in injury or death Test this Smoke CO Alarm once a week If the alarm ever fails to test correctly have it replaced immediately If the alarm is not working properly it cannot alert you to a problem This product i
28. re trademarks of Apple Inc registered in the U S and other countries HomeKit is a trademark of Apple Inc App Store is a service mark of Apple Inc The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG Inc and any use of such marks by BRK Brands Inc is under license Other trademarks and trade names are those of their respective owners Wi Fi is a registered trademark of Wi Fi Alliance Controlling HomeKit enabled accessories away from home requires an Apple TV 3rd generation or later with Apple TV software 7 0 or later and an iPhone iPad or iPod touch with iOS 9 or later 2015 BRK Brands Inc All rights reserved Distributed by BRK Brands Inc First Alert is a registered trademark of The First Alert Trust 3901 Liberty Street Road Aurora IL 60504 8122 Consumer Affairs 800 323 9005 www firstalert com www brkelectronics com 11 15 Printed in USA M08 0542 003
29. rill and in the event of an emergency It is recommended that you hold a fire drill while family members are sleeping in order to determine their response to the sound of the Smoke CO Alarm while sleeping and to determine whether they may need assistance in the event of an emergency Smoke CO Alarms cannot work without power Battery operated units cannot work if the batteries are missing disconnected or dead if the wrong type of batteries are used or if the batteries are not installed correctly AC units cannot work if the AC power is cut off for any reason open fuse or circuit breaker failure along a power line or at a power station electrical fire that burns the electrical wires etc If you are concerned about the limitations of battery or AC power install both types of units This Smoke CO Alarm will not sense smoke or CO that does not reach the sensors It will only sense smoke or CO at the sensor Smoke or CO may be present in other areas Doors or other obstructions may affect the rate at which CO or smoke reaches the sensors If bedroom doors are usually closed at night we recommend you install an alarm device Combination CO and Smoke Alarm or separate CO Alarms and Smoke Alarms in each bedroom and in the hallway between them 24 General Limitations for Smoke CO Alarms Continued This Smoke CO Alarm may not sense smoke or CO on another level of the home Example This alarm device installed on the second floor may not sense s
30. s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter 22 Special Compliance Considerations This Smoke Alarm is suitable for use in apartments condominiums townhouses hospitals day care facilities health care facilities boarding houses group homes and dormitories provided a primary fire detection system already exists to meet fire detection requirements in common areas like lobbies hallways or porches Using this Smoke Alarm in common areas may not provide sufficient warning to all residents or meet local fire protection ordinances regulations This Smoke Alarm alone is not a suitable substitute for complete fire detection systems in places housing many people like apartment buildings condominiums hotels motels dormitories hospitals health care facilities nursing homes day care facilities or group homes of any kind It is not a suitable substitute for complete fire detection systems in warehouses industrial facilities commercial buildings and special purpose non residential buildings which require special fire detection and alarm systems Depending on the building codes in your area this Smoke Alarm may be used to provide additional protection in these facilities In new construction most building codes require the use of AC or AC DC powered Smoke Alarms only In existing construction AC AC DC or DC powered Smoke Alarms can be used as specified by local buildin
31. s intended for use in ordinary indoor locations of family living units It is not designed to measure CO levels in compliance with Occupational Safety and Health Administration OSHA commercial or industrial standards Individuals with medical conditions that may make them more sensitive to carbon monoxide may consider using warning devices with provide audible and visual signals for carbon monoxide concentrations under 30ppm For additional information on carbon monoxide and your medical condition contact your physician CAUTION This combination Smoke Carbon Monoxide Alarm has two separate alarms The CO Alarm is not designed to detect fire or any other gas It will only indicate the presence of carbon monoxide has at the sensor Carbon monoxide gas may be present in other areas The Smoke Alarm will only indicate the presence of smoke that reaches the sensor The Smoke Alarm is not designed to sense gas heat or flames IMPORTANT Dangers Warnings and Cautions alert you to important operating instructions or to potentially hazardous situations Pay special attention to these items This Smoke CO Alarm is approved for use in single family residences It is NOT designed from marine or RV use 15 What You Need to Know About CO What is CO CO is an invisible odorless tasteless gas produced when fossil fuels do not burn completely or are exposed to heat usually fire Electrical appliances typically do not produce CO These
32. security put one unit in each room Many older mobile homes especially those built before 1978 have little or no insulation If your mobile home is not well insulated or if you are unsure of the amount of insulation it is important to install units on inside walls only 7 Where to Install Continued SPEAKER OPENING IN UPPER LEFT CORNER PLACE HERE OR HERE DO NOT PLACE IN THIS AREA 4 102 mm minimum between 4 6 102 mm 153 mm from ceiling CEILING WALL 8 Where Not to Install Do NOT locate this Smoke CO Alarm In garages furnace rooms crawl spaces and unfinished attics Avoid extremely dusty dirty or greasy areas Where combustion particles are produced Combustion particles form when something burns Areas to avoid include poorly ventilated kitchens garages and furnace rooms Keep units at least 20 feet 6 meters from the sources of combustion particles stove furnace water heater space heater if possible In areas where a 20 foot 6 meter distance is not possible in modular mobile or smaller homes for example it is recommended the Smoke Alarm be placed as far from these fuel burning sources as possible The placement recommendations are intended to keep these Alarms at a reasonable distance from a fuel burning source and thus reduce unwanted alarms Unwanted alarms can occur if a Smoke Alarm is placed directly next to a fuel burning source Ventilate these are
33. sounds three chirps every minute Voice Detector error Please see manual or call customer service every 5 hours Malfunction Signal Device is not work ing properly and needs to be replaced Units under warranty should be returned to manufacturer for replacement See Limited Warranty for details Horn sounds 5 chirps every minute End of Life Signal Alarm needs to be replaced Immediately replace and deactivate the alarm Does not connect to your Wi Fi Bluetooth or opportunity missed for pairing Alarm will not pair or you would like to reset the device to clear all settings Press the test button 5 times to reset alarm and try to pair to Wi Fi and Bluetooth again App FAQ If the App Problem You Should Is unable to be downloaded or installed You cannot download or install the app Only works with iOS devices not supported by Android Contact Consumer Affairs Division Carbon Monoxide Alarm ONLY CO Alarm goes back into alarm 4 minutes after you Silence it CO levels indicate a potentially danger ous situation If you are feeling symptoms of CO poisoning evacuate your home and call 911 or the Fire Department Refer to What To Do If the CO Alarm Sounds on page 10 for details CO Alarm sounds frequently even though no high levels of CO are revealed in an investigation The CO Alarm may be improperly located Refer to Where to Install on page 6 for details
34. stalert com for additional information Contents Smoke and CO Alarm Mounting Bracket Mounting Hardware User s Manual System Requirements Onelink App Search and download Onelink app from the App store Wi Fi Network For best results recommended to use with a 802 11 b g n router iOS Device HomeKit requires an iPhone iPad or iPod touch with iOS 9 or later Not compatible with Android Valid Email Account 4 Parts of this Alarm 1 Test Silence Button 2 Color Indicator Ring 3 Speaker 1 2 3 4 Mounting Bracket 5 Mounting Slots 6 Turn Alarm Clockwise to Attach 7 Turn Alarm Counterclockwise to Remove 4 7 6 5 5 Understanding Your Alarm LED Color Patterns Smoke CO Events Voice Guide Power Up and Welcome Power Up First Alert welcomes you to your Onelink Smoke and Carbon Monoxide Alarm The Onelink App will guide you through the simple setup process Programming Silencing amp Pairing voice complete Testing The testing is complete The test is done and you are protected Emergency voice complete Programming Silencing amp Pairing Location example Hallway Location Programmed Alarm silence Detector Remains Active Alarm setup has been complete Nice Work Testing Testing Alarms The alarm will sound and for your protection is very loud This may take a few secon
35. t steps 1 3 and call a qualified appliance technician to investigate for sources of CO from fuel burning equipment and appliances and inspect for proper operation of this equipment If problems are identified during this inspection have the equipment serviced immediately Note any combustion equipment not inspected by the technician and consult the manufacturers instructions or contact the manufacturers directly for more information about CO safety and this equipment Make sure that motor vehicles are not and have not been operating in an attached garage or adjacent to the residence NOTE A qualified appliance technician is defined as a person firm corporation or company that either in person or through a representative is engaged in and responsible for the installation testing servicing or replacement of heating ventilation air conditioning HVAC equipment combustion appliances and equipment and or gas fireplaces or other decorative combustion equipment Using the Silence Feature The Silence Feature This feature is intended to temporarily silence the horn while you identify and correct the problem Do not use the Silence Feature in emergency situations It will not correct a CO problem or extinguish a fire The Silence Feature can temporarily quiet an unwanted alarm for several minutes You can silence this Smoke CO Alarm by pressing the Test Silence button on the alarm cover for at least 3 5 seconds or via the Onelink app A
36. tre le fonctionnement Conform ment la r glementation d Industrie Canada le pr sent metteur radio peut fonctionner avec une antenne d un type et d un gain maximal ou inf rieur approuv pour l metteur par Industrie Canada Dans le but de r duire les risques de brouillage radio lectrique l intention des autres utilisateurs il faut choisir le type d antenne et son gain de sorte que la puissance isotrope rayonn e quivalente p i r e ne d passepas l intensit n cessaire l tablissement d une communication satisfaisante 21 Modular Devices FCC and Industry Canada Compliance Statements OEM Responsibilities to comply with FCC and Industry Canada Regulations The BLEMOD1 Module and AW CU300 Module have been certified for integration into products only by OEM integrators under the following condition 1 The transmitter module must not be co located or operating in conjunction with any other antenna or transmitter As long as the condition above is met further transmitter testing will not be required However the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed for example digital device emissions PC peripheral requirements etc IMPORTANT In the event that these conditions cannot be met for certain configurations or co location with another transmitter then the FCC and Industry Canada authorizatio
37. with a pencil Step 3 Put the unit where it won t get covered with dust when you drill the mounting holes Step 4 Using a 3 16 5 mm drill bit drill a hole through the center of the outlines you traced Step 5 Insert the plastic screw anchors in the plastic bag with screws into the holes Tap the screw anchors gently with a hammer if necessary until they are flush with the ceiling or wall Step 6 Install the screws but do not tighten completely Attach the mounting bracket by aligning the screws in the open portion of the universal mounting slots and rotating the bracket into place Tighten the screws until they are snug to secure the bracket Do not over tighten Step 7 Mount alarm to mounting bracket to activate the alarm Once unit is activated it cannot be turned off NOTE After you activate the Alarm the Color Indicator Ring will power up and the Alarm will welcome you To program your alarm follow the instructions provided in the Onelink app WARNING iOS device notifications require a functional Wi Fi connection For best results recommended to use with a 802 11 b g n router The notifications are only as reliable as your Wi Fi network and are not a substitute for a third party emergency monitoring service Speaker Opening 10 Wireless Interconnect Benefits of Wireless Interconnect The wireless interconnect feature on this alarm allows you to connect each of your First Alert Onelink alarms so when one alar
38. y Deactivating the Alarm You can also return your Alarm to us for disposal For return address see above Please include a note confirming the product is being returned for disposal This product is intended for non professional do it yourself installation If you would like information about a professionally installed and monitored system please contact First Alert Professional at 1 800 921 6025 First Alert Professional is not affiliated with BRK Brands Inc Communication distance between alarms may vary from home to home depending on environment construction materials and size of structure The quantity of alarm required will depend on these factors See manual for details 27 Copyright and Technical Specifications 2015 BRK Brands Inc All rights reserved Distributed by BRK Brands Inc Aurora Illinois 60504 First Alert is a registered trademark of The First Alert Trust BRK Brands Inc is a subsidiary of Jarden Corporation NYSE JAH Printed in USA Use of the HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod iPhone or iPad respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with iPod iPhone or iPad may affect wireless performance Apple iPhone iPad iPad Air and iPod touch a
Download Pdf Manuals
Related Search