F1 Monitor - F&V Lighting
Contents
1. amp LCD monitor User Guide Safety tips To prevent damage to your F amp V product or injury to yourself or to others Be sure to read the following safety precautions in their entirety before using this equipment Keep these safety instructions where all those who use the product will read them Cce c qo CNAB055 Q I Warning This mark indicates warning before operating the unit Please read this manual thoroughly and retain it for future reference Notes 1 Do not let any solid object or liquid fall onto or into this equipment to prevent fire or shock hazard Please avoid heavy impact on the screen Please use the adapter attached in the accessory Do not expose this product to direct sunlight when monitor is working to keep long life and quality of the screen 5 Never block the ventilation grille by covering it as that may damage monitor 6 Any smoke or unusual smell coming from the equipment please cut off and take it to service center 7 Please be noticed that it hasn t inner adjust modules Do not attempt to modify or fix this unit Contact qualified service personnel when any service is needed This equipment should never be opened for any reasons by no professional 8 Do not leave the equipment on while it is resting on or against something it may cause a fire or damage the equipment 9 Do not expose equipment to direct sunlight heat or humid conditions 10 Avoid placing2. confirm the Sound selection You should now be in the OSD submenu as shown below Use the keys to select one the following submenu items Volume 0 100 Mute ON OFF Sound Volunne TUE Troubleshooting The 7 LCD Monitor comes with a sun hood not shown that helps prevent glare while viewing in certain lighting conditions To attach the sun hood to the monitor start by carefully unfolding the sun hood then align the cable access cut out over the cable ports on the side of the monitor Peel off the film from the hook and loop adhesive tab that is directly under the cut out and firmly press the adhesive tab to the monitor Repeat this procedure for the remaining adhesive tabs being careful in keeping the hood aligned to the edges of the monitor the sun hood can be removed at any time to store for later use Troubleshooting 1 The unit Only displays a black and white image A Make sure that the color level settings are properly set for saturation brightness and contrast B Select the Exit key to switch between Color B amp W selection modes 2 No image displayed after connecting to power A Make sure the Power ON OFF key is depressed to the ON position B Make sure battery is fully charged and that the cables are properly connected 3 Image on sccreen is distorted A Select the same aspect ratio for the monitor 16 9 or 4 3 as set by your camera B Make sure cables are securely connected Broken or loose
3. select one the following submenu items Brightness 0 100 Contrast 0 100 Saturation 0 100 sharpness 0 100 Color Temp 9300K 6500 3200K User R G B 0 255 Color Brightness Contrast Saturation Sharpness Color Temp 6 OSD Press the key to access the relevant OSD on screen display menu operation Use the keys to select the OSD icon Press the key again to confirm the OSD selection You should now be in the OSD submenu as shown below Use the keys to select one the following submenu items Language faj amp 3 English H Position 0 100 V Position 0 100 OSD Timeout OFF 5 60 Seconds Transparent OFF 1 7 OSD Language English H Fosifion V Fosillon 0 OSD Timeout 1 Transparent 7 Function Press the key to access the relevant OSD on screen display menu operation Use the Q o keys to select the Function icon Press the key again to confirm the Function selection You should now be in the OSD submenu as shown below Use the Q keys to select one the following submenu items Reset Display Ratio 16 9 4 3 Auto Blue Screen ON OFF Flip Horizontal ON OFF Flip Vertical ON OFF Function Resel Display Ratio Blue Screen Flip Horizontal Flip Vertical 8 Function Press the key to access the relevant OSD on screen display menu operation Use the Q keys to select the Sound icon Press the key again to
4. the equipment near combustible or volatile solvents such as alcohol or benzine 11 Keep out of reach of children Failure to observe this precaution could result in injury ye Trademark Information HDMI High definition Multimedia Interface aretrademarks or registered trademarks of HDMI Licensing LLC ES Observe Optional proper precautions when handling batteries Batteries may leak or explode if improperly handled Observe the following precautions when handling batteries for use in this product Oo o Oo Use only batteries approved for use in this equipment Do not short or disassemble the battery Be sure the product power is off before replacing the battery Do not expose the battery to flame or to excessive heat Do not immerse in or expose to water Observe proper precautions when handling the battery charger o Keep dry Failure to observe this precaution could result in fire or electric shock o Dust on or near the metal parts of the plug should be removed with a dry cloth Continued use could result in fire Do not handle the power cable or near the charger during thunderstorms Failure to observe this precaution could result in electric shock Do not damage modify or forcibly tug or bend the power cable Do not place it under heavy objects or expose it to heat or flame Should the insulation be damaged and the wires become exposed Take the power cable to a F amp V service representative for inspection
5. Failure to observe this precaution could result in fire or electric shock Do not handle the plug or charger with wet hands Failuer to observe this precaution could result in electric shock Cleaning Your LCD Monitor Use a dry soft cloth to clean the housing You can wash the unit with a cloth and mild detergent to remove difficult stains followed with a soft cloth to dry Do not use strong cleaning agents such as thinner gasoline or alcohol as these solvents may damage the surface of the protective layer Specifications Screen size 7 0 inch Diagonal Viewing angle 70 L x70 R x70 T x50 B CR210 Display area 154 08 W x85 92 H mm Brightness 250cd m Aspect Ratio 16 9 4 3 Selectable Contrast ratio 500 1 Pixels 800x3 RGB x480 Dot Pitch 0 0642 W x0 1790 H mm Color Depth 24 bit 16 777 216 Colors Design and specifications subject to change without notice 2 Parts Diagram TFT LCD Screen 2 Infrared Window 3 Selection Keys 4 1 4 20 Female Mount 000000 Selection Key Identification Power ON OFF AV1 AV2 HD SDI HDMI or DVI input selections Down key Contrast adjustment menu list selection Up key Brightness adjustment menu list selection Menu Acticvates OSD menu selections Exit Color B amp W selectionmodes Aspect Ratio Select 16 9 or 4 3 3 UO UWY A NY 949773 390342 6 949773 390342 6 5 Audio Output 1 4 20 Female Mount 3 5mm SYNC J
6. ack mono 5 8 16V DC Main Inlet 0 1 HDMI or DVI Input Jack stereo audio AV1 Input Jack AV1 Output Jack AV2 Input Jack AV2 Output Jack Audio Input Jack 1 4 20 Swivel Shoe Mount 5 Audio Output Jack Upper Locking Ring HD SDI Input Jack 0 Swivel SHoe Mount Lock Knob 7 HD SDI Output Jack 1 Lower Locking Ring 9 9 amp GGooc og 4 Remote controller Power ON OFF a9 AV1 AV2 HD SDI HDMI or DVI input selections Left key Brightness adjustment menu list selection LCD REMOTE Right key Brightness adjustment menu list selection ww Menu Acticvates OSD menu selections Exit Color B amp W selectionmodes Setup The easiest way to ues the 7 LCD Monitor is to mount it directly to a camcorder or DSLR camera A 1 4 20 swivel shoe mount is provided for installation and features a lock knob to set the monitor at the desired viewing angle The supplied battery adapter For Sony L series batteries includes a bracket that can be mounted to the monitor prior to installing the swivel mount The battery adapter can also be mounted directly to the back of the monitor by using the supplied 1 4 mounting stud or to a light stand by using the built in hook and loop fastener on the back of the adapter Use the supplied 90 cable to make the power connection between the monitor and the battery adapter Operation Connect Li ion battery to the batt
7. cables can produce bad signals which can effect the images on screen 10 Fuzhou F amp V Photographic Equipment Co Ltd C Building No 71 Fuguang Road Fuxing Industrial Development Zone Fuzhou City Fujian 350015 P R China Tel 86 591 88088018 88088028 Fax 86 591 87324666 E Mail info fvlight com Web www fvlighting com 02011 F amp V Corporation PRINTED IN CHINA 6 949773 390342
8. ery adapter making sure cable ends are properly connected If using an external power supply no included insert the power plug 5 8 16 8V into the DC main inlet located on the side of the light unit Note The ues of any other rated external power supply could damage your light unit and void warranty Connect the appropriate input cable to the monitor and camera An HDMI to Mini HDMI cable ia included The 9 Power ON OFF key emits a solid red color indicating the power is on and is in standby mode Press the key and the red indicator light will turn off which puts the unit into working mode If there is no signal detected the key will blink red and a No Signal message will temporarily appear on screen as shown below A blue background will also appear if the menu Function is set to Blue Screen DVI input fit for Canon 5D II only 5 Menu Operation Press key to access the relevant OSD on screen display menu operation press Qo select the icons Color Adjust ODS Function or Sound and confirm the selection by pressing key Main menu Color TRI Golor Brightness Adjust Icon Contrast ODS Saturation Function Sharpness Color Temp Sound Submenu Signal data Menu interface Color Press the key to access the relevant OSD on screen display menu operation Press the key again to confirm the Color selection You should now be in the Color submenu as shown below Use the keys to
Download Pdf Manuals
Related Search