Installation Guide
Contents
1. 8 Connect your computer to one of the numbered ports on the switch s front panel 9 Enter the IP address you configured in the address field of a browser A login screen displays 10 Enter admin for the user name and leave the password field blank 11 Click the Login button The system information screen displays 12 Configure the switch for your network For more information on configuration settings and options see the M6100 Software Administration Guide Computer in DHCP Client Mode with a DHCP Server By default the switch is configured as a DHCP client to obtain its IP address from a DHCP server in the connected network You must access the switch from either the mini USB or RJ 45 console port To configure the switch 1 Make sure that the switch is connected to a DHCP server 17 2 Start a terminal emulation program TEP 3 Connect your computer to a mini USB or RJ 45 console port on the front panel of the blade 4 Configure the TEP to use the following settings Baud rate 115200 bps Data bits 8 Parity None Stop bit 1 Flow control None 5 Type the show network command and press the Enter key A screen displays that shows the active switch IP address 6 Connect your computer to one of the numbered ports on the switch s front panel 7 On the computer that is connected to the switch enter the switch IP address in the address field of a browser 18 A login2. completely into the fan tray bay 7 2 Screw the fan tray to the rear of the chassis using the included screws Install the Switch Blade To install a switch blade in a M6100 series chassis switch 1 Select a slot for the switch blade 2 Remove a blank front panel from the chassis slot if necessary Any unoccupied switch blade slot in the chassis must have a blank faceplate installed to ensure satisfactory protection from EMI and to maintain adequate air ow through the chassis 3 Remove the switch blade from the antistatic packaging CAUTION To prevent ESD damage hold the switch blade by the metal rail and front panel only Never touch the components on the PCB or the pins on any of the connectors 4 Verify that the switch blade injector ejector handles are open 5 Keep the injector ejector handles in the open position as you slide the switch blade into the chassis slot CAUTION Do not slide the switch blade into the open chassis slot if the injector ejector handles are in the latched position 8 6 Using both hands push both handles toward the center of the switch blade as shown 7 Use your fingers or a screwdriver to turn the front panel screws on each injector ejector handle clockwise and completely down When the screw is fully tightened the yellow band around the captive screw is completely hidden Console XCM8948 Supervisor PWR Status Reset PoE Max 60W per port Off no PD
3. log in to the switch Computer with a Static IP Address When the computer is in this mode the switch must also be assigned a static IP address To assign a static IP address connect a VT100 ANSI terminal or a workstation to one of the switch s console ports A cable for the mini USB port and a straight through RJ 45 cable are supplied To configure the switch 1 Start a terminal emulation program TEP 2 Connect your computer to a mini USB or RJ 45 console port on the front panel of the blade Use the installation CD to install the USB driver on your computer 14 Note You might need to install the USB serial port driver available on the CD included with the package before you can use the mini USB port on the computer to connect to the switch 3 Configure the TEP to use the following settings Baud rate 115200 bps Data bits 8 Parity None Stop bit 1 Flow control None 4 At the command prompt User log in to the switch using the user name admin and press the Enter key 5 At the password prompt press the Enter key No password is required for initial configuration 6 At the next command prompt type ezconfig and press the Enter key The ezconfig utility is now running on the switch 7 Use the following example to set up your static IP address and subnet mask Note Make sure that the selected switch IP address is in that same subnet as the computer 15 16
4. to change without notice NETGEAR Inc All rights reserved Compliance For the current EU Declaration of Conformity visit http support netgear com app answers detail a_id 11621 For regulatory compliance information visit http www netgear com about regulatory
5. Green PoE powered Yellow PoE fault RJ45 SPD Link Act Mode Green link at 1G Yellow Link at 10 100M Blink ACT OOB USB 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 9 CAUTION Be careful to avoid over torquing and stripping the screw heads Install the Power Supply To install the power supply 1 Carefully slide the power supply all the way into the power supply bay until it clicks into place CAUTION Do not slam the power supply into the system backplane Use the locking handle to secure the power supply in the power supply bay 2 Repeat Step 1 to install each additional power supply 3 After all the power supplies have been installed connect an Locking handle 10 AC power cord to the AC input connector below each power supply WARNING Be sure that the source outlet is properly grounded before plugging the AC power cord into the input connector Install Optional PoE XCM89P or UPoE XCM89UP Board You can install an optional PoE XCM89P or UPoE XCM89UP board into the XCM8944 and XCM8948 switch blades To install the optional PoE XCM89P or UPoE XCM89UP board 1 Remove the switch blade from the chassis 11 2 Connect the optional board and secure it with the attached screws as shown Configure the Switch Blade You can manage your switch thr
6. Installation NETGEAR ProSAFE M6100 Chassis Switch XCM8944 XCM8948 XCM8944F XCM8924X XCM89P XCM89UP 2 Contents M6100 Series Front Panels 3 Before Installing the Switch Blade 4 Install the Chassis 5 Install the Fan Tray 6 Install the Switch Blade 7 Install the Power Supply 9 Install Optional PoE XCM89P or UPoE XCM89UP Board 10 Configure the Switch Blade 11 3 M6100 Series Front Panels Console ports USB port 10G SFP ports 10G RJ 45 ports XCM8924X XCM8944 1G RJ 45 ports 10G SFP ports 10G RJ 45 ports 1G SFP ports 10G SFP ports 10G RJ 45 ports 1G RJ 45 ports XCM8944F XCM8948 OoB port USB port OoB port Console ports Console ports Console ports USB port OoB port USB port OoB port 4 Before Installing the Switch Bla
7. de The M6100 series switch blades are designed to be installed in the XCM8903 rack mount switch chassis NETGEAR recommends installing the XCM8903 rack mount chassis into a rack before installing any switch blades For more information about how to install the XCM8903 rack mount switch chassis see the XCM8903 Hardware Installation Guide 5 Install the Chassis You can either bracket mount the chassis into a rack or install the chassis using the included rails For more information about installing the chassis using rails see the XCM8903 Hardware Installation Guide To bracket mount the chassis 1 Partially screw two of the included screws into the rack where you want the bottom of the chassis to rest 2 Rest the bottom of the chassis s brackets on the two screws Console XCM8948 Supervisor PWR Status Reset PoE Max 60W per port Off no PD Green PoE powered Yellow PoE fault RJ45 SPD Link Act Mode Green link at 1G Yellow Link at 10 100M Blink ACT OOB USB 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 6 3 Screw the rest of the bracket to the rack Install the Fan Tray To install the fan tray 1 Carefully slide the fan tray all the way into the fan tray bay at the rear of the chassis The fan tray is connected to power when it has been inserted
8. ough its web management interface or by using the command line interface CLI through a console port This guide shows you how to configure your switch using the web management interface It also covers using the CLI to determine a DHCP assigned IP address or using ezconfig to assign a static IP address For more information about CLI management see the M6100 CLI Reference Manual and the M6100 Software Administration Manual 12 When configuring your switch connect your switch to one of the numbered ports on the switch s front panel Do not connect to the Out of Band OoB port for initial switch configuration Note Use the OoB port to manage the switch only after the switch has been configured for your network For more information about switch management using the OoB port see the M6100 CLI Reference Manual and the M6100 Software Administration Manual To configure your switch using web management use one of the following procedures depending on how your Windows computer is set up Computer is in DHCP client mode without DHCP server Computer uses a static IP address Computer is in DHCP client mode with DHCP server Computer in DHCP Client Mode Without a DHCP Server The switch assumes a default IP address of 169 254 100 100 and a subnet mask of 255 255 0 0 The switch is in the same subnet 13 used by the computer NIC port when in DHCP client mode without a DHCP server present Use this IP value to
9. screen displays 8 Enter admin for the user name and leave the password field blank 9 Click the Login button The system information screen displays 10 Configure the switch for your network For more information about configuration settings and options see the M6100 Software Administration Guide 19 NETGEAR Inc 350 East Plumeria Drive San Jose CA 95134 USA August 2014 Technical Support Thank you for selecting NETGEAR products After installing your device locate the serial number on the label of your product and use it to register your product at https my netgear com You must register your product before you can use NETGEAR telephone support NETGEAR recommends registering your product through the NETGEAR website To contact NETGEAR for support go to http support netgear com general contact or call US only 1 888 NETGEAR In other countries visit http support netgear com general contact default aspx for phone numbers For product updates and web support visit http support netgear com NETGEAR recommends that you use only the official NETGEAR support resources You can get the user manual online at http downloadcenter netgear com or through a link in the product s user interface Trademarks NETGEAR the NETGEAR logo and Connect with Innovation are trademarks and or registered trademarks of NETGEAR Inc and or its subsidiaries in the United States and or other countries Information is subject
Download Pdf Manuals
Related Search