User Manual - Hot Box Stoves
Contents
1. 22 Dansk Deutsch English Svenska Francais When stoking Each time fresh wood is put in the stove a precise amount of primary air will be allowed in for the first few minutes What s more important is that the primary air is not allowed in for too long This is to ensure optimum combustion The Aduro tronic control will ensure intake of primary air at the right tempo The automatic is activated by pulling the primary damper out each time fresh wood is put in the stove The automatic closes then the primary air gradually Regulation of the Aduro tronic control The control is pre set to allow primary air intake for the first 5 minutes This setting has been used during testing at the Danish Technological Institute using standard sized logs and with optimum moisture content of 17 20 Standard size logs are approx 30 cm long and 10 x 10 cm in thickness A standard chimney was also used for testing In practice such circumstances can differ which is why the Aduro tronic control can be adjusted to your circumstances If you want a slower intake of primary air e g for a slower flue draught larger sized wood or for longer intervals between stoking Adjust the screw on the front of the control level using a small screwdriver to slow closure rate If the screw is turned to the right closing time is increased and if turned to the left closing time is reduced 3 9 Ventilation fresh air supply In order for the w2. can cut to the size of the worn plates yourself Please consult your dealer Ash Empty the ash drawer before it becomes completely full Always leave a layer of ash on the bottom of the stove as this insulates the combustion chamber and makes lighting a fire easier Cleaning the wood burning stove The stove s surface is treated with a heat resistant Senotherm paint which will stay at its best just by being vacuumed with a small soft mouthpiece or dusted with a soft dry cloth Do not use water spirit or other solvents which will remove the paint The inside of the wood burning stove and the flue pipe can be cleaned via the door and the cleaning aperture in the flue pipe chimney The upper fireproof tile the exhaust deflector can be removed To allow free access to the top of the wood burning stove and the flue pipe remove the exhaust deflector in steel mounted with two screws Cleaning of the inside of the wood burning stove and the flue pipe should be undertaken at least once a year or more frequently if necessary depending on how often the wood burning stove is used This work can also be carried out by the chimney sweep Repairing the surface If the surface of your wood burning stove gets scratched or worn it can easily be refaced renewed using the original Senotherm paint in an aerosol can It is available in black or grey from your local dealer Please note All maintenance and cleaning of the wood burning stove should be
3. carried out when it is cold Spare parts and unauthorized alterations You may only use original spare parts in the wood burning stove Consult your dealer for advice and when purchasing spare parts All forms of unauthorized alterations to the wood burning stove are strictly forbidden as the wood burning stove will no longer comply with the approved specifications 6 0 Accessories There is a wide product range of accessories for Aduro stoves Companion sets Firebaskets in felt and bonded leather Firewood buckets Briquette bucket and ashbucket Fireplace hearth fence Glass and steel floor plates Flue pipes 7 0 Product liability and warranty In accordance with the Danish Sale of Goods Act product liability will exist for two years from the date of purchase of the wood burning stove The dated receipt will be sufficient proof Product liability will not cover damage caused by incorrect installation and use of the wood burning stove Likewise product liability will not cover loose parts and wear parts fireproof tiles glass gaskets rails cast iron grate and control as they are worn by ordinary use These parts can be purchased as spare parts 7 1 Free online warranty registration Aduro will give you the opportunity to extend the above warranty on your wood burning stove from two to five years All you need to do is to access our website at www aduro dk and register your new wood burning stove in our warranty database The warranty
4. information e The wood burning stove will become warm during use and therefore it should be treated with all necessary caution e Never keep easily combustible fluids such as petrol in the vicinity of the wood burning stove and never use easily combustible fluids to light the fire in the wood burning stove e Never empty the ash drawer when the wood burning stove is warm Embers may still be found in the ash drawer for up to 24 hours after the fire has gone out Please wait to empty the ash drawer until you are sure that there are no embers in the ash e The door should be kept closed while the wood burning stove is in use While lighting the fire the door can stand ajar for the first few minutes e Inthe event of a chimney fire Close all the dampers on the wood burning stove and call the fire fighting service 3 2 Recommended fuels We recommend the use of split hardwood that has been stored outdoors under cover for at least 1 year Wood that has been stored indoors has a tendency to become too dry and will burn too quickly The wood should preferably be felled in the winter when a lot of the moisture in the wood will have been drawn down into the roots In order to achieve optimum combustion the wood s moisture level should not exceed 18 which roughly corresponds to storing the wood under cover outdoors for one year The moisture level of the wood can be measured using a moisture meter or by applying washing up liquid to one end of t
5. the lacquered surface of the stove will become discoloured and eventually fall off The stove can be resurfaced but this is not covered by the manufacturer s guarantee In the same way any other damage to the stove caused by overloading will not be covered by the guarantee 3 8 Aduro tronic The patent applied Aduro tronic is designed to operate the stove for you All you have to do is put dry wood in the stove and activate the control system Aduro tronic does the rest leaving you to enjoy the flames and the benefits of efficient combustion Aduro tronic is a patent applied mechanical solution which works without the use of electricity Please note Use of dry wood of the right size is important to achieve optimum combustion 3 8 1 How to operate Aduro tronic When lighting When lighting a fire in the wood burning stove for the first time the maximum amount of primary air will be needed to light the fire For that reason the primary damper can be kept forcibly open This is done by pulling the primary damper forward as far as possible and then fixing it with the Aduro Key see illustration When the stove is warm and a layer of embers has been created on the bottom of the combustion chamber the Aduro tronic can be set to the automatic position i e the Aduro Key can be removed Aduro Key Alternatively you can leave the door ajar the first minutes during lighting the fire without the key
6. to expand slowly You should also be aware that the stove may make clicking sounds as it heats up and cools down rather like pouring boiling water into a sink These are caused by the great differences in temperature to which the materials are being exposed During the first firing which should be carried out using approximately 1 kg of wood the stoking door must be left slightly open and must not be closed until the stove is cold This is to prevent the sealing rope sticking to the stove 3 5 How should I use my wood burning stove The wood burning stove is intended for intermittent combustion This means that each stoking should burn down to embers before new logs are added In order to obtain the best possible combustion you should regulate the effect heat output with the fuel Burning small logs provides more powerful combustion than burning large logs as the surface area is greater and more gas is released The amount of wood in the combustion chamber is another factor that affects combustion In normal circumstances you should not place more than two logs in the stove If you want an enhanced effect you can add more logs The nominal heat output is reached by burning approx 2 2 kg per hour 21 Dansk Deutsch English Svenska Francais 3 6 Secondary damper The secondary damper behind the door should always be open while the wood burning stove is in use This damper allows you to adjust the wood burning stove to the chimney d
7. will only come into force once you have entered the required information in all the data fields The deadline for registering your wood burning stove is one month from the date of purchase 8 0 FAQ If you need more information please go to www aduro dk Enjoy your stove 24
8. Dansk Deutsch English Svenska Francais Congratulation with your new wood burning stove In order to get the best possible pleasure and benefit from your new Aduro wood burning stove it is important that you read this User Manual thoroughly before you install your wood burning stove and start to use it 1 0 General 1 1 Compliance Aduro 9 1 complies with the EN 13240 European standards as well as the NS 3058 Norwegian standard and is thereby approved for installation and use in Europe At the same time the manufacturing process is subject to external quality control The product documentation for Norway has Sintef number 110 0332 and can be downloaded from our website at www aduro no or from www nbl sintef no Aduro 9 1 also carries the Nordic Swan Eco label which guarantees that the wood burning stove complies with the most stringent environmental requirements and has been manufactured in an environmentally correct manner 1 2 Technical data Nominal power 6 kW Energy efficiency 81 3 Chimney draught 12 Pa Maximum combustion amount per hour Wood approx 3 1 kg Heat rating in buildings with Optimum insulation 150 m Average insulation 100 m Inadequate insulation 60 m Flue outlet diameter 150 mm Weight 98 kg Material steel Dimension HxWxD 958 x 500 x 459 1 3 Transportation When taking your wood burning stove home please ensure that it travels in an upright position If you wish to lay it flat
9. The floor plate should extend for at least 30 cm in front of the wood burning stove and 15 cm on each side 2 2 Pipe connection Aduro 9 1 leaves the factory with the flue outlet mounted on the top If you require the flue outlet on the back remove the round circle from the rear cover at the upper rear of the stove and then exchange the exhaust connector located on the top outlet above the stove with the cover plate that covers the rear outlet The top 19 Dansk Deutsch English Svenska Francais outlet is finished with the plate that lies in the ash drawer A flue pipe with an internal diameter of 150 mm should be used for Aduro stoves 2 3 Connection to a brick chimney If the stove is being connected to a brick chimney the rear outlet should be used or a curved flue pipe via the top outlet After measurement a hole is made in the chimney in which the pipe sleeve is placed and fireplace mortar is used to seal it in place The stove is placed in position and the flue pipe is put in place A thin gasket is placed between the flue pipe and the pipe sleeve to seal the joints The flue pipe should protrude 5 10 cm into the pipe sleeve but must not block the opening in the chimney see the illustration below The wood burning stove can be connected to a chimney to which other heat sources are connected 3 0 Lighting a fire in the wood burning stove 3 1 Important safety
10. ere may be problems with the chimney draught let the chimney sweep assess this The draught should be approx 0 10 0 14 mbar in order to provide satisfactory combustion and prevent smoke leakage If the chimney sweep judges the draught to be satisfactory but you still have problems lighting a fire try extending the fire lighting phase using more thin pieces of kindling so that the chimney gets thoroughly warm The chimney will not draw at optimum effect until it is warm The fire lighting phase can be prolonged by using a lot of kindling and 1 2 firelighters When a layer of embers has been formed add 2 3 dry logs 5 0 Maintaining and cleaning your wood burning stove Gaskets With time the gaskets will wear and in order to avoid wild combustion they must be replaced as required Glass If the wood you burn is too moist you will get soot stains on the glass pane They can be easily removed using a damp cloth that you dip in cold ash and rub on the sooty glass Special cleaning agents are also available to remove soot from glass 23 Dansk Deutsch English Svenska Francais Combustion chamber The yellow tiles in the combustion chamber eventually wear out and they should be replaced when the cracks are more that 0 5 cm The durability of the tiles will depend on how often and how intensively the stove is used You can change the tiles yourself They are available as a ready to use set You can also buy one piece tiles that you
11. he log and blowing air in the other end If the wood is dry enough soap bubbles will appear The wood should be chopped into logs with a diameter of approx 10 cm and a log length of max 39 cm Correct firing provides optimal heat output and maximum economy At the same time correct firing prevents environmental damage in the form of smoke and malodorous fumes and also reduces the risk of chimney fires Well seasoned wood fuel is essential for correct use Make sure your fuel is kept dry If the fuel is wet a large proportion of the heat will be used to vaporize the water and this energy will disappear up the chimney It is clearly not only uneconomical to fire with wet fuel but also as mentioned above increases the risk of producing soot smoke and other environmentally damaging by products Burning varnished wood impregnated wood chipboard paper and other waste is strictly forbidden Burning these materials will damage the environment the wood burning stove and your own health Fossil fuels must not be used 20 Dansk Deutsch English Svenska Francais 3 3 How do light a fire in the wood burning stove The fire lighting method is very important for starting combustion quickly and efficiently 1 Open the primary air intake damper under the door and open the secondary air intake behind the door The primary damper is used at the start to get the fire going while the secondary air intake keeps the fire burning evenly The
12. it is important that you remove all loose parts from the combustion chamber cast iron grate and loose fireproof tiles and remove the ash drawer Alternatively you could also fill the combustion chamber with excess packaging so the parts are kept in place 1 4 Serial number The wood burning stove has a serial number on the rating plate on the back of the stove Please write this number in the space below For the purposes of the guarantee and for other enquiries it is important that you are able to quote this number Serial number 18 Dansk Deutsch English Svenska Francais 2 0 Installation of the wood burning stove You are welcome to install your wood burning stove yourself but we strongly recommend that you consult your chimney sweep before you begin the installation Your dealer can also provide you with installation advice It is important to ensure that all local rules and regulations including ones relating to national and European standards are complied with when installing this device Please note You may not begin to use the wood burning stove until it has been inspected and approved by your local chimney sweep 2 1 Position of the stove distance requirements The new wood burning stove must be installed in a suitable and physically possible position You need to be sure that the position complies with local regulations Distance requirements will only apply if the wood burning stove is to be placed close to flam
13. mable materials The Aduro 9 1 should be installed at a distance of 15 cm from flammable materials at the rear and at a distance of 45 cm from the side When placing in a corner there must be 20 cm to each side All furniture must be kept at least 90 cm away from the front of the stove If the stove is installed with an insulated pipe then you may reduce the distance behind the stove to 10 cm and in the corner to 17 5 cm See illustration below If the stove is positioned against a brick wall or other non flammable material there is no minimum distance requirement To facilitate cleaning and for the best use of the convection air we recommend that you leave a distance of approximately 5 10 cm to the wall The Aduro 9 1 is built as a convection stove This means that air from the room circulates between the inner stove and the outer covering As a result the heated air is distributed evenly throughout the room med isoleret ror with insulated pipe mit isoliertem Rauchrohr Bagside Backside Ruckside A t 20 17 5 20 47 5 90 Please note that the Aduro 9 1 must be installed on a floor with the adequate load bearing capacity If the existing construction does not meet this requirement appropriate adaptation measures must be taken e g a load distributing plate If the wood burning stove is to be placed close to flammable material such as a wooden floor or carpet it must be placed on a non flammable base
14. ood burning stove to function at optimum efficiency air is needed for the combustion process There must be sufficient fresh air coming into the room containing the wood burning stove In very well insulated houses or houses with powerful cooker hoods and or air conditioning systems a vacuum can be created around the wood burning stove leading to smoke leakage and poor combustion In these circumstances it might be necessary to open a window to provide air for combustion and to equalize the vacuum Alternatively you could fit an air vent in the room containing the wood burning stove The amount of air needed for combustion is 25 m h 4 0 The chimney Data for chimney calculation Wood Flue temperature at 20 C 245 Chimney draught at testing power Imbar Pa 0 12 12 Flue gas mass flow g s 5 7 The optimum combustion is achieved at a constant chimney draught of 0 10 to 0 14 mbar measured in the flue pipe above the stove There are many factors that affect the chimney draught including the outside temperature wind strength and surrounding buildings If it is impossible to establish a sufficiently natural chimney draught the chimney can be fitted with a smoke extractor If the chimney draught is too strong a damper can be fitted to regulate the chimney draught Contact your local chimney sweep for more advice 4 1 Inadequate draught in the chimney If the chimney is too short leaks or is inadequately insulated th
15. raft and the heat output you require In normal circumstances the wood burning stove should be working with this damper open between 60 and 100 You should never close the air intake so far that the flames are extinguished There should always be visible flames in order to achieve clean and efficient combustion A too low supply of air can lead to bad combustion high emissions and a bad efficiency Aduro Key provides easier control of the secondary damper The key is fitted onto the control handle so you can more easily adjust the airflow from side to side Turning to the left decreases the airflow and turning to the right increases the airflow When the key is not in use it can hang on the edge of the drawer 3 7 Primary damper When you add a new log the primary air intake damper should be opened until the fire is burning properly In order to utilize the fuel to the fullest extent the embers should have burnt for so long that it is necessary to open the primary air intake for approx 2 minutes to get the new log to burn In order to reduce the risk of ash falling from the stove when the door is opened to add more fuel it is a good idea to open the primary air intake damper for approx 1 minute before the door is opened This increases the draught through the stove and reduces the risk that ash will drop on the floor Please note if you overload the wood burning stove and burn more than approx 3 1 kg wood hour there is a risk that
16. secondary air intake is closed when the damper is pushed all the way to the left and open when the damper is pushed to the right To open the primary air intake the damper should be pulled out The illustration below shows the stove seen from the front with the dampers indicated 2 Place a log of wood crosswise in the combustion chamber and put 2 firelighters close to the log Light the firelighters and quickly put a new log close to the firelighters and several small logs at an angle above it Air must be able to reach the firelighters but the logs should be touching to warm each other 3 Keep the door approx 1 cm ajar until the glass is too hot to touch Then close the door When there are distinct visible flames and the fire has taken hold close the primary air intake damper Secondary air intake Primary air intake Important The control handle will get warm when the wood burning stove is being used Please use the glove provided when you operate the wood burning stove 3 4 The first time a fire is lit The first few times the wood burning stove is used there may be some smoke and unpleasant odours from the wood burning stove which is fairly normal This is caused by the heat resistant paint hardening Make sure there is sufficient ventilation during this stage It is also important not to let the fire burn too fiercely the first 2 3 times so that the wood burning stove has time
Download Pdf Manuals
Related Search