Home
Invacare_wheelchair_..
Contents
1. 5 39 Adjust Arre e Ie de ER E E RE 39 Removing Installing Arrmrests 3 ete ET RR C RU ait ER DADO Ed etie 40 SEAT AND BACK 41 Replacing Back 1 E n 41 Replacing Seat Upholstery Adjusting the Seat Width i REAR WHEELS Removing Installing Rear 2 4 4 4 4 22222 46 Replacing Repairing Rear Wheel Tire 2 47 Replacing Rear Wheel Handrim 48 FRONT CASTERS 49 lnstalling Replacing Front Casters Forks 2 e tec e E er can seals 49 Adjusting Forks geen aint anna Replacing Front Casters os ANTI TIPPERS WHEEL LOCKS 0 0 51 Installing Adjusting AntinT ippers pete tieniti Re OR 51 Using Adjusting Patient Operated Wheel 54 SEAT TO FLOOR Changing Seat to Floor Height m 6 Installing Amputee o eee Ste RA b Rob Ga ES E REED EE LER DR Red Installing Crutch and Cane Carrier 61 Installing the Sea
2. AUCUN FAUTEUIL ROULANT N A T APPROUV POUR TRE UTILIS COMME SI GE L INT RIEUR D UN V HICULE MOTORIS CETTE TIQUETTE NE PEUT TRE UTILIS E QU TITRE D INFORMATION ET N A PAS T AFFICH E ICI POUR DES RAISONS DE RESPONSABILIT LEGALE Crossmember WEIGHT CAPACITY Lower Frame Tube 250 LBS 114 kgs REFER OWNER S MANUAL P N 1111013 A WARNING AWARNING 7 DO NOT OPERATE WITHOUT Refer to Owner s Manual THE ANTI TIP TUBES for proper anti tipper INSTALLED pn cotoexi44 setting 1085379 On all adjustable anti tippers REV 5 98 Invacare Tracer EX2 Part No 1110546 3 OVERVIEW 3 1 Typical Product Parameters Tracer EX2 Overall Width Permanent Arm Removable Arm 231 4 251 4 27 14 inches 24 14 261 4 281 4 inches Overall Depth with Front Riggings 3 inches Seat Width 16 18 or 20 inches Seat Depth SA Frame FF Frame 16 inches 16 inches Seat to Floor Heights with 24 inch Wheels Adult SA Frame Adult FF Frame Hemi SA Frame l9 inches 21 inches 576 inches Back Style Fixed Back Height 16 inches Arm Styles Fixed or Adjustable Height Desk or Full Length Permanent or Removable Front Riggings Swingaways Footrests and Elevating Legrests not available on FF Frame Rear Axle Permanent Rear Wheels 24 inch Composite or Urethane Handr
3. Crossbraces a Hex Screw DETAIL B CROSSBRACE HARDWARE STEPS 4 5 Coved Washers Wheelchair Frame poaz Washer O O Crossbrace Saddle FIGURE 5 Adjusting the Seat Width Swingaway Front Riggings Invacare Tracer EX2 44 Part No 1110546 8 SEAT AND BACK Fixed Frame Removing Lower Mounting Hardware 2 3 4 Remove the existing back and seat upholstery from the wheelchair Refer to Replacing Back Upholstery on page 41 If adjusting the seat width of the wheelchair back and seat upholstery as well as the crossbraces MUST be replaced Remove the four screws and locknuts that secure the insert tube to the lower wheelchair frame Remove the inserts from the rear of the wheelchair Remove the hex screw and locknut that secure the two existing crossbraces together Removing Upper Mounting Hardware WM DETAIL REMOVING UPPER While pushing down on the rear seat guide pull up the front seat guide until the front seat guide releases from the wheelchair frame Pull the crossbrace away from the rear seat guide Repeat STEPS 1 2 for opposite crossbrace Reverse STEPS 1 3 to assemble the upper mounting hardware Reverse STEPS 1 4 in Removing Lower Mounting Hardware DETAIL REMOVING LOWER Crossbrace MOUNTING HARDWARE MOUNTING HARDWARE Rear Seat Guide Insert Tube Crossbrace Hex Screw Wheelchair Frame
4. For this procedure refer to FIGURE 2 on page 52 A WARNING Anti tippers are specific to the different seat to floor angles and or seat to floor heights Refer to the chart in this section of the manual for correct usage and adjustment If these requirements cannot be achieved DO NOT use the wheelchair Contact a qualified technician If changing the seat to floor height with or without a change to seat to floor angle the correct anti tippers MUST be used to maintain a V to 2 inch ground clearance If so equipped anti tippers MUST be attached at all times Inasmuch as the anti tippers an option for 0 or 3 on this wheelchair You may order with or without the anti tippers Invacare strongly recommends ordering the anti tippers as a safeguard for the wheelchair user Anti tippers MUST be fully engaged and release buttons fully protruding out of adjustment holes ALWAYS use anti tippers When outdoors on wet soft ground or on gravel surfaces anti tippers may not provide the same level of protection against tipover Extra caution MUST be observed when traversing such surfaces Ensure both anti tippers are adjusted to the same mounting hole Part No 1110546 5l Invacare Tracer EX2 ANTI TIPPERS WHEEL LOCKS Installing Anti Tippers To ensure the correct model anti tipper is used refer to chart below Measurements for anti tippers are approximate and are taken with extension tube in bottom hole position WHEELCH
5. 2 SAFETY WARNING Avoid storing or using the wheelchair near open flame or combustible products Serious injury or damage to property may result ALWAYS keep hands and fingers clear of moving parts to avoid injury DO NOT traverse climb or go down ramps or slopes greater than 9 DO NOT attempt to move up or down an incline with a water ice or oil film DO NOT operate on roads streets or highways DO NOT ride over curbs or obstacles Doing so may cause your wheelchair to tip over and cause bodily harm to you or damage to the wheelchair DO NOT attempt to reach objects if you have to move forward in the seat DO NOT attempt to reach objects if you have to pick them up from the floor by reaching down between your knees DO NOT lean over the top of the back upholstery to reach objects behind you as this may cause the wheelchair to tip over DO shift your weight or sitting position toward direction you are reaching as the wheelchair may tip over DO NOT tip the wheelchair without assistance DO NOT use an escalator to move a wheelchair between floors Serious bodily injury may occur NEVER leave an unoccupied wheelchair on an incline Before attempting to transfer in or out of the wheelchair every precaution should be taken to reduce the gap distance Turn both casters parallel to the object you are transferring onto When transferring to and from the wheelchair ALWAYS engage both wheel locks DO NOT attempt to lift the wheelc
6. Notch Impact Guard FIGURE 6 Installing Impact Guards Calf Strap Invacare Tracer EX2 36 Part No 1110546 6 5 gv Uv ese 6 FRONT RIGGINGS Replacing Heel Loop For this procedure refer to FIGURE 7 on page 38 Pull the cam lock lever up to unlocked position Perform one of the following Footplates with Spring Buttons Detail A i Push in the release buttons and remove the footplate assembly from the front rigging support Bolt In Place Footplates Detail B i Using a screw driver to hold the threaded rivet in position remove the button head screw from the threaded rivet ii Remove the threaded rivet and button head screw securing the footplate assembly to the front rigging support Remove the mounting screw spacer and locknut that secure the heel loop to the footplate Remove existing heel loop from slide tube Install new heel loop onto slide tube Install the mounting screw spacer and locknut to secure the heel loop to the footplate Tighten until the spacer is secure Insert the lower footrest assembly into the upper footrest assembly to desired height Perform one of the following Footplates With Spring Buttons Detail A i Ensure that the release buttons fully protrude from holes on both sides of the upper footrest support Bolt In Place Footplates Detail B i From the outside of the swingaway front rigging insert the threaded rivet through both the front rigging support and th
7. Front Seat Guide FIGURE 6 Adjusting the Seat Width Fixed Frame Part No 1110546 45 Invacare Tracer EX2 9 REAR WHEELS 9 Rear Wheels A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 9 Removing Installing Rear Wheels WARNING Only a qualified technician may change the size of the rear wheel or the seat to floor height If changing the size of the rear wheel or a change in the seat to floor height is desired this procedure MUST be performed by a qualified technician Make sure both rear wheels are the same size and are installed into the same respective mounting hole before using the wheelchair otherwise injury may occur Invacare Tracer EX2 46 Part No 1110546 Permanent Axles A WARNING 9 REAR WHEELS This procedure MUST be performed by a qualified technician If replacing the same size rear wheel note the mounting position on the wheelchair frame for proper reinstallation of the new rear wheel l Remove the dust cap SA Frame only hex screw washer SA Frame only spacer if installed and locknut that secure the rear wheel to the wheelchair frame The spacer is used on wheelchairs with removable arms only 2 Repeat STEP for the opposite rear wheel if desired 3 reinstall the rear wheel s onto the wheelchair reverse STEPS 1 2 and torque locknut to 40 ft Ibs 4
8. ON BRACKET WHEELCHAIR ON WHEELCHAIR TOP TOP BOTTOM BOTTOM A and B are stamped on the sides of the amputee bracket 2 Install the amputee bracket on the wheelchair frame to the position determined in STEP I Make sure the axle spacer is pointing towards the outside of the wheelchair 3 Install the two hex screws and locknuts that secure the amputee bracket to the wheelchair 4 Install the rear wheels onto the wheelchair Refer to Removing Installing Rear Wheels on page 46 Part No 1110546 59 Invacare Tracer EX2 13 OPTIONS Bracket Adult Right Axle Spacer Toward Outside of Wheelchair Invacare Tracer EX2 Locknuts REN Rear View of Amputee Bracket FIGURE Installing Amputee Bracket 60 Bracket Adult Left Axle Spacer Toward Outside of Wheelchair Hemi Right Part No 1110546 I3 OPTIONS 13 2 Installing Crutch and Cane Carrier A WARNING Check base weekly to ensure proper placement When loading the crutch cane carrier ensure items are securely placed into the base Also ensure that there is no interference with folding the wheelchair the rear wheels or the swing back arms Strap MUST be securely fastened while carrying items NEVER insert or remove items while wheelchair is moving l Slide the clamp with the base attached over the end of the step tube o
9. attempting active use of the wheelchair Proper positioning is essential for your safety When reaching leaning or bending forward it is important to use the front casters as a tool to maintain stability and balance Part No 1110546 17 Invacare Tracer EX2 4 SAFETY HANDLING OF WHEELCHAIRS Reaching Leaning and Bending Forward or Sideways A WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees DO NOT attempt to reach or lift objects that would cause you to shift weight to one side of the wheelchair Reaching or lifting objects on the side of the wheelchair can cause the chair to tip over sideways Position the front casters so that they are extended as far forward as FIGURE I ible and heel lock Reaching Leaning and Bending Forward or possible and engage wheel locks Sideways Reaching and Leaning Backwards A WARNING DO NOT lean over the top of the back upholstery to reach objects behind you as this may cause the wheelchair to tip over Position wheelchair as close as possible to the desired object Point front casters forward to create the longest possible wheelbase Reach back only as far as your arm will extend without changing your sitting position FIGURE 2 Reaching and Leaning Backwards Invacare Tracer EX2 18 Part No 1110546 4 SAFETY HANDLING OF WHEELCHAIRS 4 5 Tipping WARNING DO NOT tip the w
10. from the wheelchair Refer to Removing Installing Rear Wheels on page 46 If necessary replace the front casters and forks with the casters and forks indicated in the chart Refer to Replacing Front Casters on page 50 Reinstall the rear wheels onto the wheelchair in the mounting position indicated in the chart Refer to Removing Installing Rear Wheels on page 46 Adjust anti tippers according to new seat to floor height Refer to Installing Adjusting Anti Tippers on page 51 Part No 1110546 57 Invacare Tracer EX2 12 SEAT TO FLOOR 8 FRONT CASTERS SEAT TO FLOOR HEIGHT FRONT CASTER REAR WHEEL SIZE REAR WHEEL IN INCHES MOUNTING POSITION MOUNTING POSITION 17 24 inch 19 Bottom 24 inch Bottom DETAIL A DETAIL B 8 INCH FORK REAR WHEEL MOUNTING POSITIONS MOUNTING POSITIONS ADULT HEMI FRAME STYLE Top TOR Middle Bottom 3 Bottom FIGURE Changing Seat to Floor Height Invacare Tracer EX2 58 Part No 1110546 13 OPTIONS 13 Options WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 13 1 Installing Amputee Bracket For this procedure refer to FIGURE on page 60 Refer to the following chart or FIGURE to determine the mounting position of the amputee bracket SEAT TO FLOOR BRACKET AXLE SPACER POSI SIDE OF BRACKET MOUNTING POSITION TION
11. solid urethane tires is not recommended If the solid urethane tire needs repaired Invacare recommends replacing the complete wheel assembly Replacement of rear wheel tube must be performed by a qualified technician Replacing Repairing Caster Tire Tube A WARNING Replacement of solid urethane semi pneumatic tires is not recommended If the solid urethane or semi pneumatic tires need replaced Invacare recommends replacing complete caster assembly For pneumatic tires replacement of the tube must be performed by a qualified technician Tire wear is excessive if e Pneumatic Tires there is missing tread or the tires are bald Urethane Tires there are cuts surface defects or the tires are loose on the rims e Rubber Tires 30 or more of the tire has worn away Invacare recommends that rear wheel tire tube and caster tire tube be replaced every five years WARNING When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool water Verify that grips are dry prior to use Use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly Failure to observe this warning may result in injury to the user or bystanders Part No 1110546 3l Invacare Tracer EX2 6 5 6 Front Riggings WARNING A After any adjustments repair or service and before use make sure all attaching hardware is tightened securely other
12. that a non folding device be installed to keep the wheelchair from being folded when left unoccupied in a public place Unfolding Tilt the wheelchair toward you raising the opposite wheel and caster off the ground floor l 2 Place your hand on the top of the seat rail closest to you where the seat upholstery is attached 3 Point your fingers and thumb to the inside of the wheelchair 4 Press downward on the top of the seat rail until the wheelchair is fully open and the seat rails are fully seated in the H blocks 5 Engage both wheel locks open the footrest legrest for clearance and transfer into the wheelchair Refer to Transferring To and From Other Seats on page 23 Seat Rail lt 3 oes Press down on the seat rail and the seat upholstery with the DO NOT wrap thumb or fingers entire hand DO NOT place any under the seat rail Point fingers and part of the hand under the seat thumb to the inside of the wheelchair rail FIGURE 7 Unfolding Invacare Tracer EX2 24 Part No 1110546 Folding 2 3 4 Swing footrest legrest in locked position to the front of the wheelchair Pivot footplates upward to vertical position With both hands grasp the middle of the seat upholstery at the front and back edge and lift up A WARNING DO NOT allow upholstery to hang between the cross braces Place excess seat upholstery over the armrest Folding Hammock or Sling Seat
13. two assistants The second assistant should be positioned at the front of the wheelchair lifting upward a non removable non detachable part of the wheelchair frame when lifting the wheelchair and stabilizing the wheelchair when the wheelchair is being lowered to the ground The first assistant should stand on the sidewalk and turn the wheelchair so that the rear wheels are against the curb Turn the anti tippers so the anti tip wheels are pointing up The wheelchair should be tilted back to the balance point and in one continuous upward movement the rear wheels should be pulled up and over the curb DO NOT return the front casters to the ground until the wheelchair has been pulled backward far enough for the front casters to clear the edge of the curb FIGURE 4 Method 2 Wheelchair Without Step Tubes A WARNING When lowering the front casters of the wheelchair DO NOT let the wheelchair drop the last few inches to the ground This could result in injury to the occupant and or damage to the wheelchair Roll the wheelchair backward and slowly lower the wheelchair in one continuous movement Turn the anti tippers so the anti tip wheels are facing down 4 6 Escalators WARNING DO NOT use an escalator to move a wheelchair between floors Serious bodily injury may occur Invacare Tracer EX2 20 Part No 1110546 4 SAFETY HANDLING OF WHEELCHAIRS 47 Stairways WARNING AN DO NOT attempt to lift a wheelchair by lifting on any rem
14. AIR MODEL SEAT TO FLOOR ANTI TIPPER MEASUREMENTS IN INCHES HEIGHT IN INCHES LENGTH HEIGHT PART NO TRACER EX2 17 to 19 2 1058836 TRACER EX2 FF 21 1086190 Anti Tipper Height Flat Surface p Bottom Position Anti Tipper Length gt NI FIGURE Installing Anti Tippers Anti Tipper Length Press the release buttons and insert the anti tippers with the anti Anti Rattle tipper wheels pointing toward the ground floor into the wheelchair frame tubing E 2 Ensure that the release button of the anti tipper fully protrudes out of the hole in the bottom of the wheelchair frame tubing Anti Tipper 3 Place the wheelchair on a flat surface Release Buttons 4 Measure the distance between the bottom of the anti tipper wheels Rear Frame Tubing and the ground floor FIGURE 2 Installing Anti Tippers Invacare Tracer EX2 52 Part No 1110546 ANTI TIPPERS WHEEL LOCKS Al Us to 2 inch clearance between the bottom of the anti tipper wheels and the ground floor MUST be maintained at all times 5 If the distance between the bottom of anti tipper wheels and the ground floor is not to 2 inches adjust anti tippers Refer to Adjusting the Anti Tippers on page 53 Adjusting the Anti Tippers Al to 2 inch clearance between the bottom of the anti tipper wheels the ground floor MUST be maintained at all times I Place the wheelchair on a flat surface If adjust
15. Adjust wheel locks Refer to Using Adjusting Patient Operated Wheel Locks on page 54 9 2 Replacing Repairing Rear Wheel Tire A WARNING Axle Mounting Axle Rear Wheel m Locknut Washer S SA Frame ONLY Wheelchair Dust Cap Frame Spacer Wheelchairs with Removable Arms ONLY Hex Screw FIGURE Removing Installing Rear Wheels Permanent Axles Replacement of the rear wheel tire MUST be performed by a qualified technician As with any vehicle check the wheels and tires periodically for cracks and wear Replace if damaged Part No 1110546 Invacare Tracer EX2 9 REAR WHEELS 9 3 Replacing Rear Wheel Handrim 6 Repeat STEPS 1 5 for the opposite rear wheel if necessary WARNING If the wheelchair is equipped with permanent axles Rear Wheel Mounting Screw this procedure MUST be performed by a qualified technician Handa S a Remove the rear wheel from the wheelchair Refer to Removing Installing Rear Wheels on page 46 2 Remove the mounting screws that secure the handrim to rear wheel Remove the existing handrim 4 Secure the new handrim to the rear wheel with mounting screws Tighten securely A WARNING Make sure the detent pin and detent balls of the quick release axles are fully released and protruding out of the hole before operating the wheelchair 9 5 Reinstall rear wheel to the wheelchair Refer to Removing Installing Rear Wheels on page 46 FIGURE 2 Replacin
16. Models Swing footrest legrest and calfpads in locked position to the front of the wheelchair Pivot footplates upward to vertical position With both hands grasp the middle of the seat upholstery at the front and back edge and lift up Continue to close the wheelchair by grasping the armrest furthest from you and pulling the armrest towards you Part No 1110546 25 4 SAFETY HANDLING OF WHEELCHAIRS FIGURE 8 Folding Invacare Tracer EX2 5 SAFETY INSPECTION TROUBLESHOOTING 5 Safety Inspection Troubleshooting 5 1 Every six months or as necessary take your wheelchair to a qualified technician for a thorough inspection and servicing Regular cleaning will reveal loose or worn parts and enhance the smooth operation of your wheelchair To operate properly and safely your wheelchair MUST be cared for just like any other vehicle Routine maintenance will extend the life and efficiency of your wheelchair Safety Inspection Checklist Initial adjustments should be made to suit your personal body structure and preference Thereafter follow these maintenance procedures Inspect Adjust Initially Ensure that the wheelchair rolls straight no excessive drag or pull to one side Inspect for loose or missing hardware on frame and crossbraces Inspect for bent frame or crossbraces Check that the wheel locks DO NOT interfere with tires when rolling Check that the wheel lock pivot po
17. Reaching Leaning and Bending Forward 2 18 Reaching and Leaning Backwards 5 e D Escalator S UTE Stairways Transferring From Other Seats e sat e tice eee ipe e Need iE 23 Wnfolding and Folding 4 itcr delta e cele e ede rU de RI 24 5 SAFETY INSPECTION TROUBLESHOOT ING sens etn seen sees seas 26 SAA Looe E EEE 26 Troubleshooting Maintenance riain M 6 5 32 Installing Removing Front Rigginigs Er Adjusting Footplate Raising Lowering Elevating Legrest Assembly Installing Guards Calf Strap eT Replacing Heel R Part 1110546 3 Invacare Tracer EX2 5 7
18. VE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN THE APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE OR LIMITATION OF HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE EXCLUSION AND LIMITATION MAY NOT BE APPLICABLE THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAWS AND REQUIREMENTS Invacare Tracer EX2 6 Part No 1110546 2 Safety 2 SAFETY The safety section contains important information for the safe operation and use of this product 2 General Guidelines WARNING DO NOT use this product or any available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as owner s manuals service manuals or instruction sheets supplied with this product or optional equipment If you are unable to understand the warnings cautions or instructions contact a healthcare professional dealer or technical personnel before attempting to use this equipment otherwise injury or damage may occur A qualified technician MUST perform the initial set up of this wheelchair Also a qualified technician MUST perform all procedures specifically indicated in the manual ACCESSORIES WARNINGS Invacare pr
19. Yes you Invacare Tracer Wheelchair U ser Man ual This manual MUST be given to the user of the product BEFORE using this product read this manual and save for future reference 9 2010 Invacare Corporation All rights reserved Republication duplication or modification in whole or in part is prohibited without prior written permission from Invacare Trademarks are identified by and 9 All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted Invacare Tracer EX2 2 Part No 1110546 5 k 2 0 0 8 9 5 Snpra D E 5 Limited Warranty ea e S tt e a UD e Ado tte bea to te toc t n Ro nto de EI 6 j L 7 General Guidelines ule iid tuts aad EE as aie eund ees 7 3 0888 Label Eocatioris ITNE AER 13 Typical Product Parameters sss 14 4 SAFETY HANDLING OF WHEELCHAIRS 16 Safecy Handling of Wheelchairs ertet etit Ree tio TOE a E aO aii l6 RR l6 Coping With Everyday Obstacles oi A Note to Wheelchair Assistants itaca iiin E A REA EA REE Ei AAN ERA R 17
20. air frame as E ho a reference See Detail A for proper positioning of the crossbrace saddle bse 8 Reinstall the two button screws locknuts and crossbrace saddle that 20 INCH 20 inch secures the bottom of the new crossbrace to the wheelchair frame 22 INCH Refer to Detail B for hardware orientation Repeat for opposite 7 F Z crossbrace Securely tighten ee X 9 Install the new back and seat upholstery onto the wheelchair Refer to DO NOT Replacing Back Upholstery on page 41 and Replacing Seat Upholstery on page 41 FIGURE 3 Adjusting the Seat Width Swingaway Front Riggings Invacare Tracer EX2 42 Part No 1110546 8 SEAT AND BACK Button Screw Crossbrace N C 3 STEPS 2 7 Locknut STEPS STEPS 2 7 2 Locknut STEPS Button Screw 27 5 5 2 7 M O NA X v es gt 4 Locknut Ee or STEPS 27 i Button Screw STEPS 3 8 Button Screw Crossbrace Saddle STEPS 2 7 STEPS 38 b ES Locknut Crossbrace Saddle E Wheelchair STEPS 3 8 STEPS 3 8 ee ay Frame pes See Detail B See Detail A FIGURE 4 Adjusting the Seat Width Swingaway Front Riggings Part No 1110546 43 Invacare Tracer EX2 8 SEAT AND BACK DETAIL Coved Washers Washer Washer Locknut DETAIL A
21. ar your seat positioning strap Inasmuch as the seat positioning strap is an option on this wheelchair you may order with or without the seat positioning strap Invacare strongly recommends ordering the seat positioning strap as an additional safeguard for the wheelchair user The seat positioning strap is a positioning strap only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts If signs of wear appear strap MUST be replaced IMMEDIATELY With regards to seat chest positioning straps it is the obligation of the DME dealer therapists and other healthcare professionals to determine if a seat chest positioning strap is required to ensure the safe operation of this equipment by the user Serious injury can occur in the event of a fall from a wheelchair Invacare Tracer EX2 8 Part No 1110546 2 SAFETY A WARNING Stability All Models The seat depth size position of the front casters size position of the rear wheels use of anti tipper model as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the seven may cause the wheelchair to decrease in stability These adjustments MUST be performed by a qualified technician The various seat to floor heights require specific settings depending on rear wheel size rear wheel position front caster size position and desired seat to floor angle These adjustments MUST be
22. e footplate assembly ii From the inside of the swingaway front rigging insert the button head screw through the appropriate adjustment hole and thread into the threaded rivet iii Using a screwdriver to hold the threaded rivet in position securely tighten the button head screw Torque to 32 in Ibs Rotate cam lock lever down to locked position Part No 1110546 37 Invacare Tracer EX2 6 5 DETAIL DETAIL Footplates with Spring Buttons Bolt in Place Footplates Front Rigging Support Front Rigging Support Button Head Screw Front Rigging Threaded Support 1 E Rivet Release Button 2 5 Footplate Assembly Adjustment Adjustment Holes i Inside of Swingaway RO Front Rigging Cam bode Cam Lock Lever Laver Footplate Assembly Footplate Assembly Outside of Swingaway Front Rigging Cam Lock Mounting ever Screw Spacer Heel Loop Slide Tube Footplate Assembly Locknut Footplate FIGURE 7 Replacing Heel Loop Invacare Tracer EX2 38 Part No 1110546 7 ARMS 7 Arms WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 7 Adjusting Armrest Height WARNING Make sure the height adjustment lever is in the locked position before using the wheelchair l Unlock the armrest by flipping the height adjustment lever
23. ed bent or broken spokes Ensure that casters are free of debris Clean upholstery and armrests with mild soap and water Check all labels are present and legible Replace if necessary Inspect Adjust Weekly Ensure that the wheel locks prevent the wheelchair from moving when engaged Inspect tires for flat spots and wear Check pneumatic tires for proper inflation If equipped check that the quick release axles lock properly Lubricate if necessary Inspect rear wheels for cracked bent or broken spokes Ensure all spokes are uniformly tight Part No 1110546 27 Invacare Tracer EX2 5 SAFETY INSPECTION TROUBLESHOOTING Inspect axle assembly for proper tension by spinning caster Caster should come to a gradual stop Inspect front caster for cracked bent or broken spokes Ensure that casters are free of debris Inspect Adjust Monthly Oooo Ensure that the wheelchair rolls straight no excessive drag or pull to one side Check that the wheel locks DO NOT interfere with tires when rolling Check that the wheel lock pivot points are free of wear and looseness Inspect seat and back for loose or broken hardware Inspect seat positioning strap for any signs of wear Ensure buckle latches Verify hardware that attaches strap to frame is secure and undamaged Replace if necessary Inspect back cane hand grips for wear loose
24. ent Operated Wheel Locks Invacare Tracer EX2 56 Part No 1110546 12 SEAT TO FLOOR 12 Seat to floor 12 1 soc WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur The seat to floor height is not adjustable for the Tracer EX2 wheelchair with the fixed frame option FF This procedure applies to the EX2 wheelchair model with swingaway footrests only Changing Seat to Floor Height WARNING The seat depth size position of the front casters size position of the rear wheels use of an anti tipper model as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the seven may cause the wheelchair to decrease in stability These adjustments MUST be performed by a qualified technician Seat to floor heights have specific positions depending on rear wheel size rear wheel position front caster size and front caster position These adjustments MUST be performed by a qualified technician If changing the seat to floor height the correct anti tippers MUST be ordered to maintain a M5 to 2 inch ground clearance For this procedure refer to FIGURE on page 58 Refer to the following chart in FIGURE to determine mounting positions for front casters forks and rear wheels for the desired obtainable seat to floor height Remove the rear wheels
25. f the wheelchair Ensure the base is towards the inside of the wheelchair 2 Position the base parallel to the step tube CAUTION na Base should be parallel to step tube to avoid Strap bending spokes when folding the wheelchair us 3 Securely tighten the locknut that secures the base to the step tube of the wheelchair Remove the upper back upholstery screw and washer B ase Align the strap with the back upholstery screw mounting hole Reinstall the back upholstery screw and washer and secure the Step strap to the wheelchair Tube 2 7 base cleans easily with any chrome or glass cleaner The strap LS Clamp E can be cleaned with mild soap and water gt T Locknut d v FIGURE 2 Installing Crutch and Cane Carrier Part No 1110546 61 Invacare Tracer EX2 13 OPTIONS 13 3 Installing the Seat Positioning Strap A WARNING ALWAYS wear your positioning strap Inasmuch as the Seat Positioning Strap is an option on this wheelchair You may order with or without the seat restraint Invacare strongly recommends ordering the Seat Positioning Strap as an additional safeguard for the wheelchair user Remove the bottom back upholstery screw from the wheelchair Position the seat positioning strap half between the back cane and back upholstery Secure the back upholstery and seat positioning strap to the wheelchair with the existing back upholstery screw ONS Repeat STEPS 1 3 for the opposite s
26. foot on the next stair above and repeats process The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from the stairway If necessary rotate the anti tippers so the wheels are facing down Part No 1110546 21 Invacare Tracer EX2 4 SAFETY HANDLING OF WHEELCHAIRS Moving Down Stairs 2 If necessary rotate the anti tippers so the wheels are facing up One assistant positioned behind the wheelchair securely grasps a non removable non detachable part of the wheelchair for leverage and tilts the wheelchair back to the balance point After the wheelchair has been tilted back to the balance point the assistant behind the wheelchair rolls the wheelchair up to the edge of the first step The second assistant positioned in the front of the wheelchair with a firm hold on a non detachable part of the framework lowers the wheelchair down and on to the next stair below and steadies the wheelchair as the assistant in the rear places one foot on the next stair below and repeats process The wheelchair should not be lowered until the last stair has been negotiated and the wheelchair has been rolled away from the stairway If necessary rotate the anti tippers so the wheels are facing down Invacare Tracer EX2 22 FIGURE 5 Stairways Part No 1110546 4 SAFETY HANDLING OF WHEELCHAIRS 4 8 Transferring and From Other Seats A WARNING Before at
27. g Rear Wheel Handrim Invacare Tracer EX2 48 Part No 1110546 10 Front Casters 10 1 WARNING DEO A WARNING 10 FRONT CASTERS After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur Installing Replacing Front Casters Forks Make sure both fork caster assemblies are the same size before using the wheelchair otherwise injury may occur This procedure be performed if replacing the exact same size front caster Remove the dust cover Remove the locknut and nylon washer that secures the fork to the caster headtube Drop the fork assembly out of the caster headtube If caster tire tube replacement is desired refer to Replacing Repairing the Front Caster Tire on page 50 Slide the new fork assembly into the caster headtube Reassemble by reversing STEPS 1 3 Repeat STEPS 1 6 for the opposite fork assembly Adjust the forks Refer to Adjusting Forks on page 50 Part No 1110546 49 o Dust Cover gue Locknut S RN Nylon Washer Caster Headtube Fork Assembly FIGURE Installing Replacing Front Casters Forks Invacare Tracer EX2 10 FRONT CASTERS 10 2 Adjusting Forks To properly tighten caster journal system and guard against flutter perform the following check Tip back of wheelchair to floor Pivot both forks and casters to top of their arc simultaneously Adjust l
28. hair by any removable detachable parts Lifting by means of any removable detachable parts of the wheelchair may result in injury to the user or damage to the wheelchair DO NOT stand on the frame of the wheelchair Part No 1110546 Invacare Tracer EX2 2 SAFETY WARNING DO NOT use the footplate as a platform When getting in or out of the wheelchair make sure that the footplates are in the upward position ALWAYS use the handrims for self propulsion Inasmuch as the handrims are an option on this wheelchair you may order with or without the handrims Invacare strongly recommends ordering the handrims as an additional safeguard for the wheelchair user Make sure detent balls of the quick release pin are fully released before operating the wheelchair ALWAYS wear your seat positioning strap Inasmuch as the seat positioning strap is an option on this wheelchair you may order with or without the seat positioning strap Invacare strongly recommends ordering the seat positioning strap as an additional safeguard for the wheelchair user The seat positioning strap is a positioning strap only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts If signs of wear appear strap MUST be replaced IMMEDIATELY The detent balls MUST be protruding past the top of the seat plate assembly for a positive lock Keep detent balls clean If the wheelchair is equipped with push to l
29. he dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address at the bottom of this page Provide dealer s name address the product model number date of purchase indicate nature of the defect and if the product is serialized indicate the serial number Do not return products to our factory without our prior consent LIMITATIONS AND EXCLUSIONS THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE PRODUCTS MODIFIED WITHOUT INVACARE S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE OR TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND INVACARE S CONTROL AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE THE WARRANTY SHALL NOT APPLY TO NORMAL WEAR AND TEAR OR FAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES WHATSOEVER WHETHER EXPRESS OR IMPLIED INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTI
30. heelchair without assistance ALWAYS check hand grips for looseness before using the wheelchair If loose and or worn replace IMMEDIATELY When tipping the wheelchair an assistant should grasp the back of the wheelchair on a non removable non detachable part Inform the wheelchair occupant before tipping the wheelchair and remind him her to lean back Be sure the occupant s feet and hands are clear of all wheels and or pinch points After mastering the techniques of tipping the wheelchair use one of the following methods to tackle curbs short stairs etc Method Wheelchair With Step Tubes Place foot on the step tube and begin to tilt the wheelchair toward you Apply a continuous downward motion until the balance point is achieved and the front casters clear the curb At this point the assistant will feel a difference in the weight distribution A WARNING When lowering the front casters of the wheelchair DO NOT let the wheelchair drop the last few inches to the ground This could result in injury to the occupant and or damage to the wheelchair Roll the wheelchair forward and slowly lower the front of the wheelchair in one continuous movement onto the sidewalk Push the wheelchair forward until the rear wheels roll up and over the curb FIGURE 3 Method Wheelchair With Step Tubes Part No 1110546 19 Invacare Tracer EX2 4 SAFETY HANDLING OF WHEELCHAIRS Method 2 Wheelchair Without Step Tubes This method requires
31. ide of the wheelchair Back Cane Back Upholstery Screw Back Upholstery 1 Strap Positioning Strap FIGURE 3 Installing the Seat Positioning Strap Invacare Tracer EX2 62 Part No 1110546 I3 OPTIONS 13 4 Installing Wheel Lock Extension Handle A WARNING If the wheelchair is equipped with push to lock wheel locks elevating legrests and wheel lock extension handles the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side otherwise injury or damage may result Interference between the top of the elevating legrest and the wheel lock extension handle causes the wheel lock to disengage For this procedure refer to FIGURE 4 l Remove the existing rubber tip from the wheel lock handle Detail 2 Install the extension handle over the wheel lock handle Detail B Detail Detail Wheel Lock Rubber Tip ul Extention Handle Wheel Lock Handle Wheel Lock Handle Wheel Lock Wheel Lock FIGURE 4 Installing the Wheel Lock Extension Handle Part No 1110546 63 Invacare Tracer EX2 Part 1110546 Rev F 08 10 Invacare Corporation USA One Invacare Way Elyria Ohio USA 44036 2125 800 333 6900 www invacare com Canada 570 Matheson Blvd E Unit 8 Mississauga Ontario L4Z 4G4 Canada 800 668 5324
32. ims Invacare Tracer EX2 Composite 14 1110546 3 OVERVIEW Tracer EX2 Wheel Locks Push to Lock Adult Pull to Lock Hemi Caster Size 8xl inch Solid Rubber Upholstery Vinyl Midnight Blue Frame Colors Chrome and colors Weight Approx Permanent Arm Removable Arm 36 pounds SA Frame 37 pounds FF Frame 36 pounds SA Frame Shipping Weight Approx Permanent Arm Removable Arm 45 1 pounds SA Frame 46 pounds FF Frame 451 3 pounds SA Frame Weight Limit These options are standard for this model 250 pounds 114 kg The seat to floor heights are based on urethane tires These heights can vary p inch due to tire wear and manufacturing tolerances Weights based on 18 wide wheelchair without front riggings Weights will vary depending on how the wheelchair is equipped Part No 1110546 15 Invacare Tracer EX2 4 SAFETY HANDLING OF WHEELCHAIRS 4 SafetylHandling of Wheelchairs A WARNING After ANY adjustments repair or service and before use make sure that all attaching hardware is tightened securely otherwise injury or damage may result 41 Safety Handling of Wheelchairs Safety and handling of the wheelchair require the close attention of the wheelchair user as well as the assistant This manual points out the most common procedures and techniques involved in the safe operation and maintenance
33. ing anti tippers on recliner models ensure back canes are in the upright position before making o adjustments Release Buttons 2 Press the release buttons on the wheeled portion of the anti tipper and slide it up or down to the desired adjustment hole 3 Check to make sure that the release buttons are fully engaged in adjustment holes 4 Ensure both anti tippers are adjusted to the same height 15 5 meh Glearance 5 Measure the distance between the bottom of the anti tipper wheels ground floor FIGURE 3 Adjusting the Anti Tippers 6 Ifthe distance between the bottom of anti tipper wheels and the ground floor is not 1 to 2 inches repeat steps 2 5 until the distance is 1 IA to 2 inches 7 Ifthe to 2 inch distance cannot be achieved a different model may be required Contact an Invacare dealer or qualified technician Part No 1110546 53 Invacare Tracer EX2 ANTI TIPPERS WHEEL LOCKS 11 2 Using Adjusting Patient Operated Wheel Locks Using Patient Operated Wheel Locks A WARNING DO NOT attempt to stop a moving wheelchair with wheel locks Wheel locks are not brakes If the wheelchair is equipped with push to lock wheel locks elevating legrests and wheel lock extension handles the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side otherwise injury or damage may result Interference between the top of the elevating leg
34. ing support and lower footplate assembly From the outside of the swingaway front rigging insert the threaded rivet through both the front rigging support and the footplate assembly From the inside of the swingaway front rigging insert the button head screw through the appropriate adjustment hole and thread into the threaded rivet Using a screwdriver to hold the threaded rivet in position securely tighten the button head screw Torque to 32 165 Rotate cam lock lever down to locked position Repeat STEPS 1 9 to adjust the remaining footrest Front Rigging Support Front Rigging Support Button Head e Threaded Rivet Swingaway Adjustment footrest shown Hole Button Head Screw Adjustment H Threaded Rivet Footplate Cam Lock L Footplate Assembly Assembly Inside of Swingaway Front Rigging Outside of Swingaway Front Rigging FIGURE 3 Adjusting Footplate Height Bolt In Place Invacare Tracer EX2 34 Part No 1110546 Fixed Frame 2 tH 6 3 Remove impact guards and or calf strap if necessary Loosen but do not remove the bolt and locknut that secure the lower footrest assembly to the upper footrest support Reposition the lower footrest assembly to the desired height Securely tighten the bolt and locknut Repeat this procedure for the other footrest if necessary Replace impact guards and or calf strap if necessary Raising L
35. ints are free of wear and looseness Check that the wheel locks are easy to engage Ensure that the wheel locks prevent the wheelchair from moving when engaged Inspect the seat and back for rips and sagging Inspect the seat and back for loose or broken hardware Inspect the back cane hand grips for wear looseness deterioration Inspect seat positioning strap for any signs of wear Ensure buckle latches Verify hardware that attaches strap to frame is secure and undamaged Replace if necessary Inspect tires for flat spots and wear Check pneumatic tires for proper inflation Invacare Tracer EX2 26 Part No 1110546 5 SAFETY INSPECTION TROUBLESHOOTING A WARNING As with any vehicle check the wheels and tires periodically for cracks and wear Replace if damaged If equipped check that the quick release axles lock properly Lubricate if necessary Check that there is no excessive side movement or binding in the rear wheels when lifted and spun Inspect rear wheels for cracked bent or broken spokes Ensure all spokes are uniformly tight Inspect handrims for signs of rough edges or peeling Inspect axle assembly for proper tension by spinning caster Caster should come to a gradual stop Adjust front casters forks bearing system if wheel wobbles noticeably or binds to a stop Ensure wheel bearings are clean and free of moisture Check headtube locknuts for tightness Inspect casters for cracks and wear Inspect front casters for crack
36. lance at all times Your wheelchair has been designed to remain upright and stable during normal daily activities as long as you DO NOT move beyond the center of gravity Virtually all activities which involve movement in the wheelchair have an effect on the center of gravity Invacare recommends using seat chest positioning straps for additional safety while involved in activities that shift your weight Invacare Tracer EX2 16 Part No 1110546 4 SAFETY HANDLING OF WHEELCHAIRS DO NOT lean forward out of the wheelchair any further than the length of the armrests Make sure the casters are pointing in the forward position whenever you lean forward This can be achieved by advancing the wheelchair and then reversing it in a straight line 4 3 Coping With Everyday Obstacles Coping with the irritation of everyday obstacles can be alleviated somewhat by learning how to manage your wheelchair Keep in mind your center of gravity to maintain stability and balance 4 4 Note to Wheelchair Assistants When assistance to the wheelchair user is required remember to use good body mechanics Keep your back straight and bend your knees whenever tipping the wheelchair or traversing curbs or other impediments DO NOT attempt to lift the wheelchair by any removable detachable parts Lifting by means of any removable detachable parts of the wheelchair may result in injury to the user or damage to the wheelchair If the wheelchair is exposed to extre
37. me temperature above 00 F or below 32 F high humidity and or becomes wet prior to use ensure handgrips DO NOT twist on the wheelchair s handle otherwise damage or injury may occur Also be aware of detachable parts such as armrests or legrests These MUST NEVER be used to move the wheelchair or as lifting supports as they may be inadvertently released resulting in possible injury to the user and or assistant s When learning a new assistance technique have an experienced assistant help you before attempting it alone A WARNING DO NOT attempt to reach objects if you have to move forward in the seat or pick them up from the floor by reaching down between your knees The seat depth size position of the front casters size position of the rear wheels use of anti tipper model as well as the user condition directly relate to the stability of the wheelchair Any change to one or any combination of the seven may cause the wheelchair to decrease in stability These adjustments MUST be performed by a qualified technician Many activities require the wheelchair owner to reach bend and transfer in and out of the wheelchair These movements will cause a change to the normal balance the center of gravity and the weight distribution of the wheelchair To determine and establish your particular safety limits practice bending reaching and transferring activities in several combinations in the presence of a qualified healthcare professional before
38. ness deterioration Adjust front casters forks bearing system if wheel wobbles noticeably or binds to a stop Ensure wheel bearings are clean and free of moisture Check headtube locknuts for tightness Inspect Adjust Periodically Inspect frame and crossbraces for loose or missing hardware Inspect for bent frame or crossbraces Check that wheel locks are easy to engage Inspect seat and backs for rips and sagging Check that there is no excessive side movement or binding in the rear wheels when lifted and spun Inspect handrims for signs of rough edges or peeling Adjust front casters forks bearing system if wheel wobbles noticeably or binds to a stop Ensure wheel bearings are clean and free of moisture Invacare Tracer EX2 28 Part No 1110546 m 5 2 Troubleshooting Inspect casters for cracks and wear Ensure that casters are free of debris Clean upholstery and armrests with mild soap and water Check that all labels are present and legible Replace if necessary 5 SAFETY INSPECTION TROUBLESHOOTING Chair Chair 3 Sluggish Turnor Casters Squeaks and Looseness in Solutions Veers Wheels Performance Flutter Rattles Chair Right Left Check tires for correct and X X X X equal pressure Check for loose nuts and bolts X X Check caster headtube angle Check that rear wheels are equally spaced away from seat frame Par
39. ns Release Button one set above the other Each set will be visible one at a time allowing finer footplate height adjustment Adjustment 3 Push in the release buttons and reposition the footplate assembly Holes to the desired height Footplate Assembly 4 Ensure that the release buttons fully protrude from holes on both sides of the front rigging support Rotate cam lock lever down to locked position Cam Lock Lever Repeat this procedure for the other footplate if necessary 7 Reinstall the swingaway front rigging assembly Refer to Installing Removing Front Riggings on page 32 Swingaway footrest shown FIGURE 2 Adjusting Footplate Height Spring Button Part No 1110546 33 Invacare Tracer EX2 6 FRONT RIGGINGS Bolt In Place 0 Qo Lv This procedure applies to the swingaway front riggings and swingaway elevating legrest Remove the swingaway front rigging Refer to Installing Removing Front Riggings on page 32 Lay the front rigging assembly on a flat surface to simplify this procedure Pull the cam lock lever up to the unlocked position Using a screw driver to hold the threaded rivet in position remove the button head screw from the threaded rivet Remove the threaded rivet and button head screw securing the footplate assembly to the front rigging support Adjust the footplate assembly height by aligning the desired adjustment holes in the upper front rigg
40. ocedure refer to FIGURE 3 FIGURE 4 on page 43 and FIGURE 5 on page 44 When adjusting the seat width of the wheelchair the back and seat upholstery MUST be changed If applicable the headrest pillow and headrest upholstery MUST be changed as well the existing back and seat upholstery from the wheelchair Refer to Replacing Back Upholstery and Replacing Seat Upholstery on page 41 2 Remove the four button screws and locknuts that secure the two pivot links to the wheelchair frame and crossbraces 3 Remove the two button screws locknuts and crossbrace saddle that secures the bottom of the crossbrace to the wheelchair frame Repeat for other crossbrace 4 Remove the hex screw coved washers washers and locknut that secure the two crossbraces together See Detail B Note the orientation of the coved washers washers and locknut for assembling the new crossbraces See Detail B 5 Assemble the two new crossbraces together with the existing hex screw coved washers washers and locknut Securely tighten Refer to Detail B for hardware orientation 6 Determine the correct pivot link and mounting hole to use with the desired seat width SEAT WIDTH PIVOT LINK 7 Securethe pivot links to the crossbraces and wheelchair frame with the four button screws and locknuts Securely tighten ed 16 inch 18 inch Position crossbrace saddle on wheelchair frame using 2 y ER 5 the washer on the underside of the wheelch
41. ock wheel locks elevating legrests and wheel lock extension handles the wheel lock extension handles MUST be removed before swinging the elevating legrests to the side otherwise injury or damage may result Interference between the top of the elevating legrest and the wheel lock extension handle may cause the wheel lock to disengage Wheel locks are not brakes DO NOT attempt to stop a moving wheelchair with wheel locks Engaging the wheel locks may not prevent the wheelchair from moving on all floor surfaces including those that may be wet or slick Always exercise caution when transferring into or out of your wheelchair Weight Training Invacare does not recommend the use of its wheelchairs as a weight training apparatus Invacare wheelchairs have not been designed or tested as a seat for any kind of weight training If occupant uses said wheelchair as a weight training apparatus Invacare shall not be liable for bodily injury or damage to the wheelchair and the warranty is void Weight Limitation The Tracer EX2 has a weight limitation of 250 pounds 114 kg Invacare Tracer EX2 12 Part No 1110546 3 OVERVIEW 3 Overview 3 Label Locations NO WHEELCHAIR HAS BEEN APPROVED FOR USE AS A SEATING SURFACE WITHIN A MOTOR VEHICLE THIS LABEL IS FOR INFORMATIONAL PURPOSES ONLY LIABILITY ISSUES WERE NOT CONSIDERED IN THE ATTACHMENT OF THIS LABEL X Brace that attaches at the left hip MEN Serial Number Label located on
42. ocknuts according to freedom of caster swing mgom 2 Test wheelchair for maneuverability 3 Readjust locknuts if necessary and repeat STEPS 1 2 until correct 4 Snap dust cover over the locknut and stem 10 3 Replacing Front Casters A WARNING Make sure both front casters are the same size and are installed into the same respective mounting hole before using the wheelchair otherwise injury may occur Note the mounting position on the fork assembly for proper reinstallation of the new front caster l Remove the hex screw washers and locknut that secure the front caster to the fork Washers are only used with 8 inch casters with precision bearings 2 reinstall the new front caster onto the fork reverse step Invacare Tracer EX2 50 Let casters drop to bottom of arc wheels should swing once to one side then IMMEDIATELY rest in a straight downward position Repeat STEPS C D until wheels swing once to one side then IMMEDIATELY rest in a downward position 6 or 8 inch Fork Locknut 5 Washer if applicable Washer if applicable oe Front Caster FIGURE 2 Replacing Front Casters Part No 1110546 ANTI TIPPERS WHEEL LOCKS Anti tippers Wheel Locks A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur 11 1 Installing Adjusting Anti Tippers
43. oducts are specifically designed and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products NOTICE THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE Check all parts for shipping damage and test before using In case of damage DO NOT use Contact Invacare Carrier for further instruction Part No 1110546 7 Invacare Tracer EX2 2 SAFETY WARNING Wheelchair User As a manufacturer of wheelchairs Invacare endeavors to supply a wide variety of wheelchairs to meet many needs of the end user However final selection of the type of wheelchair to be used by an individual rests solely with the user and his her healthcare professional capable of making such a selection Wheelchair Tie Down Restraints and Seat Positioning Strap Wheelchair users should NOT be transported in vehicles of any kind while in wheelchairs As of this date the Department of Transportation has not approved any tie down systems for transportation of a user while in a wheelchair in a moving vehicle of any type It is Invacare s position that users of wheelchairs should be transferred into appropriate seating in vehicles for transportation and use be made of the restraints made available by the auto industry Invacare cannot and does not recommend any wheelchair transportation systems ALWAYS we
44. of the wheelchair It is important to practice and master these safe techniques until you are comfortable in maneuvering around the frequently encountered architectural barriers Use this information only as a basic guide The techniques that are discussed on the following pages have been used successfully by many Individual wheelchair users often develop skills to deal with daily living activities that may differ from those described in this manual Invacare recognizes and encourages each individual to try what works best for him her in overcoming architectural obstacles that they may encounter However all warnings and cautions given in this manual MUST be heeded Techniques in this manual are a starting point for the new wheelchair user and assistant with safety as the most important consideration for all 4 20 Stability and Balance WARNING ALWAYS wear your seat positioning strap Inasmuch as the seat positioning strap is an option on this wheelchair you may order with or without the seat positioning strap Invacare strongly recommends ordering the seat positioning strap as an additional safeguard for the wheelchair user The seat positioning strap is a positioning strap only It is not designed for use as a safety device withstanding high stress loads such as auto or aircraft safety belts If signs of wear appear strap MUST be replaced IMMEDIATELY To assure stability and proper operation of your wheelchair you MUST maintain proper ba
45. on the top front of the armrest to the up horizontal position Locked Vertical Height Adjustment Lever 2 Adjust the armrest to one of five positions Armrest Height adjustment lever MUST be in the unlocked position when placing armrest into the arm assembly 3 Lock the armrest by pressing the height adjustment lever into the down vertical position when the desired armrest height is achieved l 33 4 Repeat STEPS 1 3 for the other armrest Unlocked Horizontal FIGURE Adjusting Armrest Height Part No 1110546 39 Invacare Tracer EX2 7 ARMS 7 2 Removing Installing Armrests A WARNING Make sure the height adjustment lever is in the locked position before using the wheelchair Removing Armrest Push down on armrest to ensure it is fully seated in front and rear sockets STEP prevents the release buttons from hanging up on the sockets during removal 2 Press in the armrest release button at the front and rear of the armrest 3 While pressing in the armrest release buttons remove the armrest from the arm sockets by pulling straight up Installing Armrest l Position the armrest just above the front and rear arm sockets 2 Push arm down evenly at the front and rear until the front and rear armrest release buttons snap into the arm sockets Ensure armrest is locked securely in the arm sockets by gently lifting up If not locked repeat STEPS 1 3 A
46. ovable detachable parts Lifting by means of any removable detachable parts of the wheelchair may result in injury to the user or damage to the wheelchair ALWAYS check hand grips for looseness before using the wheelchair If loose and or worn replace IMMEDIATELY Extreme caution is advised when it is necessary to move an occupied or unoccupied wheelchair up or down the stairs Invacare recommends that if possible the user be removed from the wheelchair prior to moving Invacare recommends using two assistants and making thorough preparations Make sure to use only secure non detachable parts for hand held supports For this procedure refer to FIGURE 5 on page 22 Follow this procedure for moving the wheelchair between floors when an elevator is not available Moving Up Stairs If necessary rotate the anti tippers so the wheels are facing up 2 One assistant positioned behind the wheelchair securely grasps a non removable non detachable part of the wheelchair for leverage and tilts the wheelchair back to the balance point After the wheelchair has been tilted back to the balance point the assistant behind the wheelchair backs the wheelchair up against the first step 4 second assistant positioned in the front of the wheelchair with a firm hold on a non detachable part of the framework lifts the wheelchair up and on to the next stair above and steadies the wheelchair as the assistant behind the wheelchair places one
47. owering Elevating Legrest Assembly A WARNING Ensure hands and fingers are clear of elevating legrest mechanism before pushing release lever to lower the elevating legrest Otherwise injury may occur due to pinch points The wheelchair user s leg MUST be supported by an assistant before attempting to lower legrest To raise the elevating legrest the assistant should hold the support tube and raise the elevating legrest until the desired height is obtained To lower the elevating legrest perform the following A Support user leg with one hand B Push release lever downward with other hand C Gently lower user leg down and rest against the legrest Part No 1110546 35 6 FRONT RIGGINGS Wheelchair Frame Footplate Assembly FIGURE 4 Adjusting Footplate Height Fixed Frame Release Lever FIGURE 5 Raising Lowering Elevating Legrest Assembly Invacare Tracer EX2 6 5 6 4 Installing Impact Guards Calf Strap Remove impact guard calf strap from packaged container if not already secured to the footrest 2 Secure one impact guard to each footrest Ensure the upper portion of the impact guard is between the two horizontal supports of the footrest 3 Secure one side of the calf strap around each footrest with the impact guards attached if present Horizontal Support Calf Strap Footrest SS Upper Portion of Impact Guard Horizontal Support
48. performed by a qualified technician When changes to the left hand column occur follow across the chart and N m N 2 e refer to the procedure that is checked gt to maintain the proper Hi HO amp e i stability safety and handling of the wheelchair 2 m IE E E a 2 OO 5 9 2 lt CASTER SIZE Y Y Y Y CASTER POSITION Y Y Y Y Y WHEEL SIZE Y Y Y Y Y WHEEL POSITION Y Y Y Y Y ANTI TIPPERS Y Y Y Y Y USER CONDITION Y Y Y Y Y Part 1110546 9 Invacare Tracer EX2 2 SAFETY WARNING Anti Tippers Anti tippers are specific to the different seat to floor angles and or seat to floor heights Refer to the chart in this section of the manual for correct usage and adjustment If these requirements cannot be achieved DO NOT use the wheelchair Contact a qualified technician If changing the seat to floor height with or without a change to seat to floor angle the correct anti tippers MUST be used to maintain a 1 to 2 inch ground clearance If so equipped anti tippers MUST be attached at all times Inasmuch as the anti tippers are an option for 0 or 3 on this wheelchair You may order with or without the anti tippers Invacare strongly recommends ordering the anti tippers as a safeguard for the wheelchair user Anti tippers MUST be fully engaged and release buttons fully protruding out of adjustment holes ALWAYS use anti tippers When ou
49. rest and the wheel lock extension handle may cause the wheel lock to disengage Position wheelchair on a flat level surface to perform this procedure Ensure the wheelchair is not moving before engaging the wheel locks l See Detail A for instructions Push to Lock Refer to Detail for instructions on Pull to Lock 2 Disengage the wheel locks by reversing the directions in STEP on Pull wheel lock handle toward the tire to disengage wheel lock the tire to engage wheel lock Unlocked Position Wheel Lock Detail Push To Lock Locked Position Pull wheel lock handle backward toward the tire to engage wheel lock to diserigage wheel lock Wheel Lock Detail B Pull To Lock FIGURE 4 Using Patient Operated Wheel Locks Unlocked Position Locked Position Invacare Tracer EX2 54 Part No 1110546 ANTI TIPPERS WHEEL LOCKS Adjusting Patient Operated Wheel Locks 10 A WARNING DO NOT attempt to stop a moving wheelchair with wheel locks Wheel locks are not brakes If wheel locks do not hold the occupied wheelchair in place contact a qualified technician otherwise injury or damage may occur If wheels are pneumatic before adjusting the wheel lock assemblies ensure that the tires are inflated to the recommended psi on the side wall of the tire Position wheelchair on a flat level surface to perform this procedure Ensure the wheel lock is in
50. rmrest Release Button Armrest Release Button Rear Arm Socket Front Arm Socket li al D i 0 4 Fr FIGURE 2 Removing Installing Armrests Invacare Tracer EX2 40 Part No 1110546 8 SEAT AND BACK 8 Seat and Back 8 1 WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely otherwise injury or damage may occur Replacing Back Upholstery Remove the eight mounting screws and washers that secure the existing back upholstery to the back canes 2 Remove existing back upholstery from the back canes 3 Securely tighten the new back upholstery to the back canes with the phillips screws and washers 8 2 Replacing Seat Upholstery l Remove the eight phillips screws and washers that secure the existing seat upholstery to the crossbraces 2 Remove the existing seat upholstery from the crossbraces 3 Ensure positioning of seat positioning strap if used Refer to Installing the Seat Positioning Strap on page 62 4 Install new seat upholstery by reversing STEPS 1 2 Part No 1110546 41 Back Upholstery Washers c Mounting gt L Screws Washers FIGURE Replacing Back Upholstery Mounting 16 Seat Depth Seat Upholstery Wheelchair Frame FIGURE 2 Replacing Seat Upholstery Invacare Tracer EX2 8 SEAT AND BACK 8 3 Adjusting the Seat Width Swingaway Front Riggings For this pr
51. t No 1110546 29 Invacare Tracer EX2 5 SAFETY INSPECTION TROUBLESHOOTING 5 3 Maintenance Maintenance Safety Precautions A WARNING After any adjustments repair or service and before use make sure all attaching hardware is tightened securely Otherwise injury or damage may result A CAUTION DO NOT overtighten hardware attaching to the frame This could cause damage to the frame tubing Suggested Maintenance Procedures Before using your wheelchair make sure all nuts and bolts are tight Check all parts for damage or wear and replace Check all parts for proper adjustment Periodically adjust wheel locks in correlation to tire wear Refer to Adjusting Patient Operated Wheel Locks on page 55 Periodically check handrims to ensure they are secured to the rear wheels If loose have them tightened by a qualified technician Periodically check caster wheel bearings to make sure they are clean and free from moisture Use a Teflon lubricant if necessary Hand grips should be checked monthly for wear looseness deterioration Clean if desired Replace if looseness or deterioration is found CO eS 201 es Check upholstery for sagging rips or tears A CAUTION As with any vehicle check the wheels and tires periodically for cracks and wear Replace as recommended Invacare Tracer EX2 30 Part No 1110546 5 SAFETY INSPECTION TROUBLESHOOTING Replacing Repairing Rear Wheel Tire Tube WARNING Replacement of
52. t Positioning Strap 62 Installing the Wheel Lock Extension Handle eterne tentent tente tentent tnnt tnn senten ttn EEES EROE tentent trente tenentes 63 Invacare Tracer EX2 4 Part No 1110546 GENERAL General 1 1 Symbols Warnings Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage See the information below for definitions of the signal words DANGER Danger indicates an imminently hazardous situation which if not avoided will result in death or serious injury WARNING Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Caution indicates a potentially hazardous situation which if not avoided may result in property damage or minor injury or both IMPORTANT Indicates a hazardous situation that could result in damage to property if it is not avoided Gives useful tips recommendations and information for efficient trouble free use Part No 1110546 5 Invacare Tracer GENERAL 1 2 Limited Warranty PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser who purchases this product when new and unused from Invacare or a dealer This warranty is not ex
53. tdoors on wet soft ground or on gravel surfaces anti tippers may not provide the same level of protection against tipover Extra caution MUST be observed when traversing such surfaces Ensure both anti tippers are adjusted to the same mounting hole Operating Information After adjustments repair or service and BEFORE use make sure all attaching hardware is tightened securely otherwise injury or damage may result DO NOT overtighten hardware attaching to the frame This could cause damage to the frame tubing Unless otherwise noted all service and adjustment should be performed while the wheelchair is unoccupied Determine and establish your particular safety limits Practice bending reaching and transferring activities in several combinations in the presence of a qualified healthcare professional before attempting active use of the wheelchair When cleaning the rear cane or hand grip areas use only a clean towel lightly dampened with cool water Verify that grips are dry prior to use The use of soap or ammonia based cleaning solutions will result in the hand grips sliding off the cane assembly Failure to observe this warning may result in injury to the user or bystanders If the wheelchair is exposed to extreme temperature above 00 F or below 32 F high humidity and or becomes wet prior to use ensure that the handgrips DO NOT twist on the handle Otherwise damage or injury may occur Invacare Tracer EX2 10 Part No 1110546
54. tempting to transfer in or out of the wheelchair every precaution should be taken to reduce the gap distance Turn both casters parallel to the object you are transferring onto Also be certain the wheel locks are engaged to help prevent the wheels from moving A CAUTION When transferring position yourself as far back as possible in the seat This will help prevent damaged upholstery and the possibility of the wheelchair tipping forward This activity may be performed independently provided you have adequate mobility and upper body strength Position the wheelchair as close as possible alongside the seat to which you are transferring with the front casters pointing parallel to it Remove or flip up the armrest Engage wheel locks Swing away or remove front rigging Shift body weight into seat with transfer During independent transfer little or no seat platform will be beneath you Use a transfer board if at all possible FIGURE 6 Transferring To and From Other Seats Part No 1110546 23 Invacare Tracer 4 SAFETY HANDLING OF WHEELCHAIRS 4 9 Unfolding and Folding Wheelchair A WARNING ALWAYS keep hands and fingers clear of moving parts to avoid injury DO NOT place hand or fingers on the underside of the seat frame rail when opening or closing the wheelchair DO NOT sit or transfer into the wheelchair unless it is fully open and the seat frame rails are fully seated into the side frame H blocks Invacare recommends
55. tended to any other person or entity and is not transferable or assignable to any subsequent purchaser or owner Coverage under this warranty will end upon any such subsequent sale or other transfer of title to any other person This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state Invacare warrants the side frames and cross members of this product when purchased new and unused to be free from defects in materials and workmanship for a period of five 5 years from the date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty Invacare warrants the upholstered materials seat back and armrests of the arm assembly and remaining components of this product when purchased new and unused to be free from defects in materials and workmanship for a period of thirteen 13 months from date of purchase from Invacare or a dealer with a copy of the seller s invoice required for coverage under this warranty If within such warranty periods any such product shall be proven to be defective such product shall be repaired or replaced at Invacare s option This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact t
56. the open unlocked position Loosen the bolt and locknut that secure the wheel lock assembly to the wheelchair frame Reposition the wheel lock so that when engaged the wheel lock shoe embeds the tire lis inch Clg inch for pneumatic tires and holds the occupied wheelchair in place when pushed Securely tighten the bolt and locknut attaching the wheel lock to the wheelchair frame Engage the wheel lock Measure the distance the wheel lock is embedded into the tire as shown in Detail A Any wheel lock adjustment should embed the wheel lock shoe at least l inch ena inch for pneumatic tires into the tire when engaged Repeat the STEPS 1 6 until the wheel lock shoe embeds the tire lig inch Clie inch for pneumatic tires and holds the wheelchair in place when pushed Repeat STEPS 1 7 for the opposite wheel lock If the measurement of e 16 inch for other tires cannot be achieved remove the bolt and locknut that secure the wheel lock to the wheelchair frame and mount the wheel lock in the remaining mounting position Repeat STEPS 1 8 Engage both wheel locks and ensure the occupied wheelchair is held in place when pushed Part No 1110546 55 Invacare Tracer EX2 ANTI TIPPERS WHEEL LOCKS Bolt and Wheel Lock DETAIL inch P 6 inch Locknut Handle pneumatic tires Wheel Lock Shoe Wheel Lock M Wheel Lock Shoe Tire Mounting Positions Rear Wheel FIGURE 5 Using Pati
57. wise injury or damage may occur 6 1 Installing Removing Front Riggings Installing Front Rigging Turn the front rigging assembly to the side lever 2 Install the hinge plates on the front rigging assembly onto the hinge pins on the wheelchair frame 3 Push the front rigging assembly towards the inside of the wheelchair Front Rigging until it locks into place Hinge lt I iT Assembly The footplate will be on the inside of the wheelchair when locked in place Footplate Repeat this procedure for the other front rigging assembly 5 release the front rigging push the front rigging release lever inward rotate front rigging outward Removing Push the front rigging release lever inward 2 Rotate swingaway front rigging assembly outward Swingaway footrest shown 3 Lift the swingaway front rigging assembly off the hinge pins FIGURE Installing Removing Front Riggings Invacare Tracer EX2 32 Part No 1110546 6 5 6 2 Adjusting Footplate Height Spring Button This procedure applies to the swingaway front riggings and swingaway elevating legrest l Remove the front rigging assembly Refer to Installing Removin Front Riggings on page 32 Lay the front rigging assembly on a flat surface to simplify this procedure Front Rigging Support 2 Pull the cam lock lever up to unlocked position The elevating legrest has two sets of release butto
Download Pdf Manuals
Related Search
Related Contents
User`s Manual / Manual de Usuario / Guide d`Utilisation Data Reduction Manual 浴槽・床・壁 Philips SAECO Espresso Italiano Copyright © All rights reserved.
Failed to retrieve file