Home

20R00-50 Omni IIe Owner`s Manual V2.13

1. SCENES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 X X X X 2 X X X X 3 X X X X 4 X X X X 5 X X X X 6 X X X X 7 X X X X 8 X X X X 9 X X X X 2 0 x X 11 X X X X gt 12 X X X X gt 13 X X X X 14 X X X X Z 15 X X IX X gt 16 x Ix Ix x X Corresponds to the unit numbers in a Scene Page 27 Scene Commands Scene Commands are used to Set Scenes issue a Scene On command and issue a Scene Off command To issue Scene Commands press the 2 SCENE key You are prompted to enter a Scene number ENTER SCENE 1 64 Enter the Scene number 1 64 followed be key SCENE 1 O OFF 1 ON 2 SET Scene Set Command The Scene Set command is used to set up Scenes for a lighting group Set the desired lighting level for each of the units in the lighting group for the first Scene The desired lighting level may be set manually at the switch or by a command issued from the controller After the desired lighting levels are set press the 2 SET key to save the first Scene for that group Commands are sent to each of the four units in that group to instruct each unit to save its current lighting level as the lighting level for the Scene Repeat these steps to set up each of the remaining three Scenes for that lighting group Scene On Command Once the Scenes have been set up press the 1 ON key to command the four units in
2. 41 Clear Messages 2 1085 41 DAY 41 Phone A 41 Anes 41 Telephone Interface eS A shee ee a oR 43 M HOUSE Ro RA adhe acc RAS 43 Remote a Aa Secs hod A ees BLE 43 Phone Access Denied Remote Lockout lt cccccccccceesscccceccsstecedinciveieceseecuacesde 44 Alternate Method e o 44 E ee end tate Oe MR 44 cote oa EN 45 2 E E E 45 GOTO ATE a 45 32 45 45 5 ea hades Oe a eae heed os doc aden ea va ee doo 45 G F SCAU
3. 69 Answer Outside Call 69 ienen EE ERE EEE 70 Rings Before Answers rise occ sine ea ea eee ee es eg Bee ates 70 70 My Phone eee eee ee I 70 Dial Out Number 1 70 Dial Out Numbers 28 th en 71 36 Ga ee eer ee ee 71 Set Wp Arming gcc aden een eae te aden cee te ete De ae cl on Eee a ha Bite ol bac an tas a a 71 Entry Delays xcs KRR ENE GRE E a ees Ri 71 1 72 Exit Time Restarts 72 Univacated Premises Re eb ean os 72 Chime va ae aces ee peated ap es eg Bee ae 72 Perimeter Chime EE Rute ashe heat en 72 Enable Quick 72 5 73 Alb ah vice dest ls 73
4. ee 73 Set up ER EE AEEA E EEE E EEEN EE E 73 High Security RRE ese E een eee 73 Announce Alarms ere eee 73 Enable Freeze E 8 Oia use 74 Flash For en 74 Console 1 8 Audible Exit Delay 74 House Codes l 4 Format be 74 House All ote ob ota aces Caucus Soe 74 CIO CK Seiki he 75 Latitude Longitude and Sadek een oe bn E ses Avo eee ea ee 76 Daylight Savings s atid ein Red se ast edna 77 Controller Cdr 6S Da coe ba teeters 77 Controller NUMBER ben Wades cues N 78 Encryption Key cast een heh eh seo Bok hh eB ee Bie AR en ae a eee 78 UP NAMES eie iier 79 Set Up cnco nenii eiie
5. entered cae chee eae es eae tek 46 46 8 Phones i e E A A ae ee a a 47 wis aceite WA Glas hg Wa Ge ae eee 47 Panic Button over the Phone HHE ancients wate ak A We aioe na sta deen Ad ae ae 47 Emergency Dial Out oc ee heed oes a see a ee ed Saeed ws Re oe EE 48 Digital sok oe 48 Voice BF eee eee eee 48 How Omni Voice Dialer Works 48 What the Omni Voice 06 48 What the Omni Voice Dialer 49 What You Hear If Your Omni Calls 49 a dept Pane en eke ese E ATE 49 amp DO Ethernet Port Wins a aha ieee 50 Controller IP Address Port Number and En
6. eee 27 pera 27 KE E E 28 63 6 E 28 Scene OniComimand 28 Scene Off Command 2 cen Sse iach 28 UPB oe a 28 Activating and Deactivating Links 29 Setting a Link Lighting Scemes sc cc 29 Executing Phantom Buttons 29 Executing Centralite SCenes 22 225 E E 29 es ARI GR SES 30 Lemperature Controls 30 5 Phermostats aces eat oe wh A eee tate Mette a ee ae 31 Programmable Energy Saver Modules PESMS c cccssessesssesseeeseesecesecesecesecnaeceaecseecaeeeseseaeeeeeseceeeeeeeesuecsa
7. HOME AUTOMATION INC OMNI AUTOMATION Owner s Manual Includes the SIA CP 01 Control Panel Standard Features for False Alarm Reduction Document Number 20R00 50 Rev 2 13 September 2006 Copyright 2001 2006 Home Automation Inc All Rights Reserved Contents Unde rwriter s Laboratoti s UL Tistin a ek 1 eee Tee Sa Roe I ee E E 2 Normal Top Level Display 2 E 3 ere 3 gia saat 4 11 TE 4 Trouble 4 Confirmation 5 Cancel Ten aven sede Meet eee Leeda 5 Out E EE 5 5 5 Disarming the Security System and Silencing Alarms 6 Armi
8. EES 57 Edit Programs cis neern en o E E A EE E Ea E EEE REES Ees 58 Times Programs rein L E EAER RE E E RARR E 58 Button and Event na 01a T 11a KARTE ETET T E A 59 Control Unit Switch Press Event Buttons e E a eaa e EE E 59 28 T E A E E E E 60 BATAI DTPA E E ET A 61 Event Buttons a a e 61 Buttons cea tent Ai es cat cage a ote ts a tan Mecsas See te has 62 Alarm Event 8 62 Event Buttons aces TN Peas ava aN aE Tend eee ES 62 Miscellaneous Event Buttons vba 63 Message Event Buttons Pro Link ste cutseieedeadecddesedecceses 63 Switch Press Event Buttons CentraL ite iE o EE E E 64 Edit Program 64 Program Control Commands a 64 Unit Toggle Command 65 Program Secu
9. E E 79 Up Address eh eed Hod sot Se teh 80 UNDERWRITER S LABORATORIES REQUIREMENTS SL FIRE ESCAPE PLANNING pits E E 81 FEDERAL COMMUNICATION COMMISSION NOTICE ssccssssssssssssscescsscscssssssessessesssessseseors 82 CANADIAN INDUSTRY CANADA NO TIC Bis APPENDIX DIAL PLANNER 6essivescssaiservosttestaensesssscescdiecaspuseascebadvesesshssaceibeadicessedssedcdedbaispataoacnene OF INSTRUCTIONS TO CALLED PARTY 85 APPENDIX TEXT DESCRIPTION CHARACTER 96 APPENDIX C VOICE DESCRIPTION CODES wisssssscassusscornsacessssecsebsesitusceunsodscssneqdsetesendonevssscsdsensedesoade INTRODUCTION Thank you for purchasing your new Omni automation system You are about to enjoy a new feeling of security comfort convenience and control Omni coordinates lighting heating and air security scenes and messages based on your lifestyle and schedule Please take a few moments to become familiar with all of the features of your system by reviewing this manual Please keep this manual on file for future reference It is recommended that you also review the installation and operating instructions provided with your smoke and gas detecto
10. To Bypass or Restore a zone in Area 2 from a console in Area 1 or viceversa it is first necessary to go to that area 2 2 From security menu press GOTO key on console keypad AREA ENTER AREA The Area number be entered followed by the key or use arrow keys to scroll through list of areas Once area is selected you are prompted to enter your code GOTO AREA 2 ENTER CODE The console AREA 1 will now be temporarily assigned to the selected area AREA 2 if a valid code for that area AREA 2 is entered All security and control commands will now operate on the selected area AREA 2 just as if you were physically at a console assigned to that area AREA 2 All status displays will show the status of the selected area The top line of the display will show the name and security mode for that area Use the go to function again to return to the area normally assigned to that console AREA 1 The console will automatically return to its normal area after three minutes of inactivity at the console Page 15 Testing Your System HAI recommends testing your system on a weekly basis to ensure that you are fully protected 1 Notify your Central Station that you intend to test the system To test the siren press 1 and 3 keys simultaneously Press OFF and enter your Code to cancel the alarm and silence the siren To test the security zones you will need
11. 21 of HLC Lighting tee Reis ea 21 Configuring Lighting Scenes in an HLC 22 Controlling Individual Lighting Loads in HLC Room or UPB 22 Controlling 23 Controlling RadigRA 23 Controlling 23 Ramp Command ALC Eg 24 Controlling Compose renee 24 Scene Command Compose a E 25 Timed Command scenes oe 25 Stat s fa PS 25 Flags 25 Controlling RE ude weed cle E A 26 AVVO ih sabes soe 26 Tg 27 27
12. At any time the alarm system can be turned off at the console Page 10 Fire Alarm Activated When the fire alarm is activated by the smoke fire detector s the alarm responds exactly as described under Burglar Alarm Activated except e The console display reads FIRE ALARM ZONE NAME TRIPPED sounder will activate in a 3 pulse temporal pattern to distinguish the fire alarm from the burglar alarm The fire alarm takes priority over the burglar alarm however if a gas alarm is already active it will not override the gas alarm NOTES gt If multiple alarm types occur such as both Fire and Police the display will alternate between the alarm types gt reset smoke detectors arm the system When armed the controller will cycle power to reset smoke detectors Gas Alarm Activated When the gas alarm is activated the alarm responds exactly as described under Burglar Alarm Activated except console display reads GAS ALARM ZONE NAME TRIPPED The sounder will pulse on off on then an extended off period to distinguish it from the burglar or fire alarm The gas alarm takes priority over the burglar alarm however if a fire alarm is already active it will not override the fire alarm NOTE gt To reset gas detectors arm the system When armed the controller will cycle power to reset gas detectors Emergency Keys Emergency alarm conditions can be activated through the console These conditions Fire P
13. HEAT SETTING COOL SETTING FAN HOLD STATUS CANCEL Ifthe STATUS key is selected Omni will read the current status of the thermostat For instance TEMPERATURE IS 80 HEAT SETTING IS 60 COOL SETTING IS 75 MODE IS COOL FAN IS AUTO HOLD IS OFF When a Programmable Energy Saver PESM is entered ZONE 9 ENERGY SAVER ENERGY SAVER IS ON OFF TEMPERATURE IS PLEASE CHOOSE OFF ON HEAT SETTING COOL SETTING TIMED STATUS CANCEL OWNH Ifthe STATUS key is selected Omni will read current status of the PESM For instance ENERGY SAVER IS ON OFF TEMPERATURE IS 80 HEAT SETTING IS 60 COOL SETTING IS 75 6 Status Press 6 from the MAIN MENU to get to the STATUS menu From the Status menu Omni will report the Security Mode for the current Area If all zones are secure and there are no troubles with the system Omni reports System OK If any zones are currently not ready in trouble or bypassed Omni will report the current status of those zones Any system troubles are also reported Finally Omni will report the current Outdoor Temperature if part of the system and the current time and date 7 Events Press 7 from the MAIN MENU to get to the EVENT menu The Omni will read the 3 latest events Press 7 key for Omni to read 3 more events to cancel Page 46 8 Ph
14. The console is designed with everything that is necessary for you to program and operate your Omni control and security system Because we feel that it is very important for you to feel comfortable with the operation of your Omni we recommend that you start by becoming familiar with your console The OFF 1 DAY 2 NIGHT 3 and AWAY 4 keys are called shortcut keys This means that you may press these keys to go directly to that function without having to go into one of the hidden menus Omni MATION UY N CONTROL SECURITY BUTTONS 5 A Fa ALL TEMP STATUS a VN 2 D AK 2 REY 2 EY 47 EVENTS MESSAGE SETUP i a CANCEL MENU 1 OFF The OFF key is used to disarm deactivate the security system reset emergency alarms and silence all sirens and sounders 2 DAY The DAY key is used to arm the security system in the Day mode In the Day mode the perimeter zones doors and windows are protected however the interior zones are not armed so that you may move about freely inside In this mode there is an entry delay on entry exit zones 3 NIGHT The NIGHT key is used to arm the security system in the Night mode In the Night mode the doors windows and non sleeping area motion detectors are armed In this mode there is no entry delay so the alarm will be activated immediately if any zone is violated 4 AWAY Th
15. key to display message or simply press the down arrow key to scroll through a list of messages Press the key to display the selected message Thu Oct 04 O1 4 06 PM TRASH NIGHT When the message is displayed the console will beep 4 times and the console LED will flash continuously You may press the key to acknowledge seeing the message This will cause the LED to stop flashing however the message will remain on the display until it is manually cleared or cleared by a program Log Message The 2 LOG key allows you to store the selected text message s in the Event Log This can be a helpful to keep track of the times and dates of events and occurrences You may enter the message number followed by the key to log that message or simply press the down arrow key to scroll through a list of messages Press the key to log the selected message Clear Message The 3 CLEAR key allows you to clear the selected text message or all text messages from the console s display TRASH NIGHT ENTER MESSAGE O ALL 4 You may enter the message number followed by key to clear that message or simply press the down arrow key to scroll through a list of messages Press the key to clear the selected message or press 0 then to clear all messages Say Message Note To Say a message the HAI Two Way Audio Module with a speaker must be installed The 4 SAY key allows the controller to say the selected voi
16. 2 99 seconds 1 99 minutes or 1 10 hours Next enter a number 0 100 to indicate the final lighting level intensity desired LIGHTING LEVEL 0 100 The keypad will beep and the lighting level will be adjusted The keypad display top line will read Entry Lights 40 AT 1H Controlling Compose Units Entry Lights O OFF 1 ON 2 DIM 3 BRT 4 Entry Lights 4 SCN 9 TIM STAT Press 0 OFF to turn the selected unit off Press 1 ON to turn the selected unit on Press 2 DIM to dim the selected unit 1 9 steps each step is 10 from its current level Press 3 BRT to brighten the selected unit 1 9 steps each step is 10 from its current level Press 4 SCN to set a group of lights to their predefined lighting levels VV VV V WV Press 9 TIM to time the selected unit On or Off Timed commands may be from 1 99 seconds 1 99 minutes or 1 18 hours gt Press STA to view the current status of the unit Page 24 Scene Command Compose If Compose lighting switches are part of your installation the Scene SCN command is used to set a group of lights to predefined lighting levels There is an Off command an On command and 12 lighting scenes for each group of Compose lighting switches SCENE O OFF 1 0 2 13 A L Enter 0 followed by key to turn the lights that are part of the selected group off Enter 1 followed by key to set the lights that are part of the selected group to prede
17. Choose NONE when editing a program and choose not to conditionalize the program SELECT CONDITION NEVER 1 Choose NEVER if you wish to temporarily deactivate a program without deleting it Other conditions include IF LIGHT IF DARK IF ENERGY LO IF ENERGY MID IF ENERGY HI IF ENERGY CRIT IF PHONE DEAD IF PHONE RING IF PHONE OFFHK IF PHONE ONHOOK IF AC PWR OFF IF AC PWR ON IF BATTERY LOW IF BATTERY OK Set Up Dial The Set Up Dial menu is used to configure all of the telephone related items for the Omni To enter the Set Up Dial menu from the Setup menu press the 4 DIAL key Use the arrows to scroll through the items For each item the top line displays a description of the item and its current setting The bottom line shows the available ranges for your selections Phone numbers can be up to 24 characters long The number is shown on the bottom line of the display Press the OFF key to enter a into the number Press the DAY key to specify a pause of 2 seconds shown as on the display Press the NIGHT key to enter a into the number Enter a single for no number Telephone Access The Telephone Access item allows you to turn the local in house and remote telephone control feature on and off If set to On the Omni will allow local and remote telephone access as described in Telephone Control If set to Off the Omni will not answer incoming calls ever and will not work on the in house
18. FIRE ALARM AUXILIARY ALARM TEMPERATURE ALARM WATER ALARM GAS ALARM SILENT ALARM AND ADDRESS Your address here PHONE NUMBER your phone number here The Omni will repeat this message twice Entering the Code At any time during the message you can enter the Master or Manager code simply by pressing the digits on the keypad of a Touch Tone phone The Omni will stop talking when it hears any digit from a touch tone phone When it is saying the address the Omni completes the entire address before it stops talking If you enter the correct Master or Manager code you will then be logged in a remote phone access is logged in the event log and further dial outs are canceled You will hear the status of the system which will describe the type of alarm and the zones tripped for example BURGLAR ALARM ACTIVATED ZONE ENTRY EXIT TRIPPED ZONE 3 DAY INTERIOR TRIPPED Then the Omni will read the Main Menu as described in Telephone Control You can press 0 to hear the menu At this point you are in control just as if you had called your system A strategy to follow if you are called by your system is to check the Status 6 on the telephone to see what mode the system is in and which zones were tripped Press to cancel out of the status mode You may wish to check the Event Log 7 to see when each event happened Then press to exit the event log Now press 9 good bye to make
19. When the House Code is configured as UPB RadioRA or CentraLite House Code All On does not affect the state of the installed devices however if this setup item is set to Yes Omni will change the status of all units on that House Code to even though it doesn t explicitly send an All On command to those units If the House Code All On setup item is set to No Omni will not change the status of units on that House Code Time Clocks There are three Time Clocks in the system are used to conditionalize programs They are used solely to define time periods during the week when certain programs should be enabled or disabled to execute TIME CLOCK 1 ON TIME CLOCK 1 OFF Specify the on and off times for each Time Clock See Set Up Codes TIME CLOCK 1 ON TIME 12 00 MTWTFSS CHNG TIME CLOCK 1 OFF TIME NEVER CHNG For example it may be desirable to conditionalize certain programs to execute only during normal Monday Friday 9 00 5 00 PM work week The default for Time Clock 1 ON is 12 00 MTWTESS and default for Time Clock 1 OFF is Never so that Time Clock 1 is always Enabled TIME CLOCK 2 ON TIME CLOCK 2 OFF TIME CLOCK 3 ON TIME CLOCK 3 OFF Time Clocks 2 and 3 is entered into the system and set for time and dates exactly like the settings for Time Clock 1 Page 75 Latitude Longitude and Time Zone The system automatically calculates the time
20. each key functions as a menu choice 10 CONSOLE BEEPER The Console Beeper is used to confirm a keystroke alert user of errors and troubles and sound upon entry and exit delays 11 KEY The Key is used to cancel and return display to previous menu When you are entering number will cancel the previously entered digits and will prompt you to reenter the number 12 KEY The Key is used to enter or confirm a selection It may also be used to display a menu or to offer you additional choices Normal Top Level Display In its normal state the console display will show the day date and time on the top line and the system status on the bottom line If all doors windows sensors etc are closed no zones are bypassed and if there are no troubles the bottom line will show SYSTEM OK as seen below Thu Feb 23 06 4 00 PM SYSTEM OK If one of the doors windows motion or other detector connected to the Omni is open or has detected motion the bottom line of the display will say ZONE NAME NOT RDY For example the display will show FRONT DOOR NOT RDY If the zone name has not been entered during set up the display will give the zone number and zone type This display will remain for 2 seconds then the next zone not ready in trouble or bypassed will be displayed Display Menus The system has been designed to be easy to operate Whenever you press a key on the console the top line
21. 2 DELETE gt Press the 1 EDIT key to edit the selected program The Edit Program menu is displayed which allows the various parts of the program to be changed See Edit Program Edit each part of the program as specified under Edit Program Press the key at the Edit Program menu to show the newly edited program Press the key again to save the program or press key to cancel edit of this program and return to reviewing the programs gt Press the 2 DELETE key to delete the selected program 3 Delete All Programs To delete All automation programs from the Set Up Program menu press the 3 DELETE key The display will prompt you to confirm the deletion DELETE ALL PROGRAMS O NO 1 YES Select 1 YES to delete all automation control programs in the system Select 0 NO or press key to return to the Set Up Program menu NOTE IF YOU CHOOSE THIS OPTION ALL OF YOUR PROGRAMS WILL BE LOST PERMANENTLY Edit Programs The Edit Program menu is used to specify each part of an automation program EDIT PROGRAM 1 WHEN 2 CMD 3 amp COND Selecting 1 WHEN allows the time or event that activated the program to be specified Selecting 2 CMD allows you to specify the action to be taken when the program is executed Selecting 3 amp COND allows a condition to be specified that must be true for the program to be executed at the specified time Each of these items defaults to its current setting
22. HAI UPB 8 Button House Controller allows for controlling all 8 rooms of lighting where HAI UPB Wall Switches Dimmers and Modules have been installed It can also be configured as a general purpose 8 button keypad controller used to trigger 8 different macro programs in the Omni controller or to toggle between two different actions i e turn lighting load on turn lighting load off each time a pushbutton is pressed When used to control rooms of lighting in the HLC structure each button on the House Controller is used to toggle all of the lights in the respective room on and off When the room is turned on the LED indicator behind the respective button is illuminated and all of the lights in the room are turned on When the room is turned off the LED indicator behind the respective button is turned off and all of the lights in the room are turned off lighting load in the respective room is turned on the LED indicator behind the button is illuminated When all lighting loads in the respective room are turned off the LED indicator behind the button is turned off When used to control rooms of lighting in the HLC structure each House Controller controls 8 consecutive rooms i e Room 1 8 To configure a House Controller to control a group of 8 rooms it must be set to the last unit number in one of the respective rooms For example a House Controller set to Unit 8 16 24 32 40 48 56 or 64 is configured to control rooms 1 8 Th
23. HLC House Codes 1 4 All Off This feature allows you to choose if House Code 1 4 will respond to the All Off command Press the 0 key to select No and 1 key to select Yes After selecting press down arrow key to change this option for the next House Code HC 1 ALL OFF 1 0 1 YES 1 The default setting for HC 1 4 Offis Yes Page 74 Notes 1 When configured each House Code will affect 2 rooms of HLC lighting i e HC 1 ALL OFF affects Room 1 and 2 2 When the House Code is configured as UPB RadioRA or CentraLite House Code All Off does not affect the state of the installed devices however if this setup item is set to Yes Omni will change the status of all units on that House Code to Off even though it doesn t explicitly send an All Off command to those units If the House Code Off setup item is set to No Omni will not change the status of units on that House Code House Codes 1 4 All On This feature allows you to choose if House Code 1 4 will respond to the All On command Press the 0 key to select No and 1 key to select Yes After selecting press the down arrow key to change this option for the next House Code HC 1 ALL ON 0 1 YES 1 The default setting for HC 1 4 is Yes Notes 1 When configured each House Code will affect 2 rooms of HLC lighting i e HC 1 ALL ON affects Room 1 and 2 2
24. Log records the 250 most recent significant security system Events happenings and trouble conditions in the system When a new event occurs the oldest one is lost The following Events along with the time and date of their occurrence are recorded in the Event Log when they occur All Security system arming and disarming events Off Day Night Away and Vacation and user name All zones bypassed or restored by the user and user name Any zone automatically bypassed by the system Any zone shutdown by the system Swinger Shutdown Any zone tripped while the security system is armed Any trouble condition zone battery fuse AC power or phone The restoration of any trouble condition the trouble condition ceased to occur Any Remote Telephone Access Remote Access Denied or Remote PC Access Page 39 Show Events To view your event log from the top level display or from the main menu press the 7 key then enter your code The arrow keys may be used to scroll through the event log starting with the most recent event Each event log entry displays the time and date on the top line and a description of the event on the bottom line 7 15 PM 5 8 USER NAME AWAY For trouble conditions the event log will show the zone name or specific trouble condition and TROUBLE 10 59 AM 5 8 BATTERY TROUBLE For trouble restorations the event log will show the zone name or specific trouble condition and TRBL RST 11 57 AM 5 8
25. Zone or area of lighting in a RadioRA system Accessory Switches and Dimmers are used to control the lights locally from up to 9 additional locations Master controls provide control and monitoring for all the lights RadioRA system Phantom Buttons are virtual buttons in the RS232 Interface Though there are no physical buttons that represent these Phantom Buttons they work very similarly to buttons on RadioRA Master Controls Phantom Buttons are intended to give the RS232 Interface control over multiple RadioRA Switches and Dimmers with one command To control more than one device at one time Phantom Buttons are recommended A Zone is any individual RadioRA Switch or Dimmer A RadioRA System has a maximum of 32 Lighting Zones Zone Numbers can be used to identify any individual Zone one Switch or one Dimmer in a RadioRA system via the RS232 Interface The Chronos System Bridge and Timeclock bridges two RadioRA systems for a total of 64 Lighting Zone Controls and 24 Master Controls Page 19 When to RadioRA the Omni controller can gt Send commands off and level to individual Switches and Dimmers gt Receive status on and off from individual Switches and Dimmers gt Receive commands when buttons are pressed on Master Controls gt Execute Phantom Button commands About ALC ALC is intended for installation in homes which have been pre wired for installation of ALC system products Omni controls lig
26. a partner to walk around your home and open and close all doors windows etc that are connected to the system while you watch the console Have a partner open each door and window then close it The display should show the zone name as being NOT RDY and then return to SYSTEM OK when closed Have your partner walk in front of all motion detectors if installed and verify that the console responds in a similar fashion Test your smoke detectors as recommended by the manufacturer Be ready to silence the alarm system as soon as it sounds From the top level display or from the main menu press the 6 key then the 4 key The Battery reading should be over 200 See Status Test Pick up an inside phone and press the key When the menu is spoken press 8 Then 3 The Omni should say ADDRESS IS and play your name and address If it does the telephone dialer telephone access and telephone control systems are all working correctly If you wish to test your system s link to your Central Station monitoring service call them first and inform them that you will be testing your alarm system Set off the alarm allowing sufficient time for the Dial Out Delay if enabled and then turn the alarm system Off The Central Station should receive the alarm code and cancel signal Remember to inform your Central Station when the test is complete To see a complete list of alarm system activities view the system event log See Event Log Page 1
27. an alarm is canceled during a Voice Dial Out the system hangs up immediately Page 12 Trouble Indications The Omni constantly monitors the alarm zones and several internal matters and will alert you if it detects trouble The particular trouble is indicated on the bottom line of the display and a trouble signal is given by beeping the console beeper continuously 2 beeps per second When any trouble condition occurs the console will beep twice per second and continue to beep until the key cancel is pressed to acknowledge the trouble The console will say TRBL NOW trouble now if the trouble condition actually exists while you are looking at the console It will say HAD TRBL had trouble if the trouble occurred and then corrected itself The following are trouble indications and their meanings gt ZONE NAME TRBL NOW or HAD TRBL If the reading for a zone becomes abnormal trouble will be indicated on that zone See Status Test Excessive resistance in the contact and wiring usually causes trouble on security zones If the cause is not obvious call your installer for service gt AC POWER OFF TRBL NOW or HAD TRBL Indicated if the normal house current powering the Omni controller is interrupted for more than 3 minutes If this happens without good cause check the wall mounted transformer to ensure that it hasn t come out of the wall socket and check to see that the socket has power gt BATTERY LOW TRBL NOW or H
28. are connecting from the Internet enter either the public IP address way to reach your local network via the Internet or domain name e g www homeauto com 3 Enter the port number that is configured for the controller 4 Select the Encryption tab Enter the two part encryption key as it is displayed on the console 5 Select OK 6 Click Connect gt gt Network gt gt Connect PC Access should change from Off Line to On Line The Modem item on the main menu has been replaced with the Connect item The submenu under Connect then allows selection of Modem Serial or Network When an account file is opened the connection type will default to Serial Page 50 192 168 0 101 Hub HAI Omni Router Controller To connect to Omni controller local network using HAI PC Access under Configure gt gt Network enter the controller s IP address 192 168 0 50 i e 192 168 0 101 ae Computer 192 168 0 51 Computer Local Network Dynamic DNS If the controller is connected to the Internet via a dynamic IP address to locate and communicate with the controller from remote locations over the Internet using HAI PC Access you must subscribe to a Dynamic DNS Domain Name Service Dynamic DNS is a service that maps your dynamic changing IP address to a static permanent hostname allowing you to access your Omni controller over the Internet using
29. desired button number These can be specified by entering the number followed by key or by using the arrow keys to scroll through a list of items BUTTON ENTER BUTTON MENU 4 Pressing key first will bring up a menu of event button types to select from BUTTON TYPE 1 CTRL 2 SEC 3 ZONE 4 4 ALL 5 ALARM 6 X 10 7 MISC If there are no programs for the specified item the console will beep three times and will display NO PROGRAMS Otherwise a help screen is displayed Press to delete or edit displayed program Page 56 The first program is displayed once down arrow is pressed The top line displays time or button event that activates program and any condition that must be true for the program to activate The bottom line shows the command to execute when the program is activated 10 00 MIWTFSS amp AWAY Living Rm Lt ON 6 00 AM 10 10 amp NIGHT PROGRAM DAY WHEN AWAY ALL OFF When 2 conditions are part of a single program the conditions are not displayed on the console Instead amp MULTI is displayed to let you know that this program line contains 2 conditions To view or edit the program you must use the PC Access Software WHEN ZONE 1 NR amp MULTI FOYER LIGHT ON The arrow keys are used to scroll through the programs Pressing key while a particular program is displayed will allow that program to be edited or deleted The display shows SHOW PROGRAM 1 EDIT
30. down arrow key J PORT NUMBER 4369 0 65535 In most installations default port number can remain the same Port numbers range from 0 to 65535 To change port number enter the new port number followed by key to store the port number Port numbers 0 to 1024 are reserved for designated services and should not be used Encryption Key Encryption and decryption of data between the Omni controller and the connected device is based on the Advanced Encryption Standard AES using a 128 bit cryptographic key A unique encryption key is randomly assigned to each Omni controller at the factory no records of these keys are kept at the factory It may be left the same recommended or it may be changed as desired To view and assign the encryption key from the previous Setup item PORT NUMBER press the down arrow key 4 ENCRYPTION KEY PT 1 6F 1B 26 A2 FF D9 E4 12 This key consists of 16 bytes that is 16 2 digit values from 0 9 and or the letters A F It is entered into the controller in two parts PT 1 and PT 2 consisting of 8 bytes each Enter the 2 digit value To enter the digits A F first press the OFF key then press the 0 5 key respectively i e Al OFF 0 1 and CB OFF 2 OFF 1 After the last digit 16 digit has been entered press the key to store PT 1 of the encryption key Press the down arrow key J to enter 2 of the encryption key ENCRYPTION KEY PT 2 DC 6
31. ee oe 11 Police Emergency AREA ad ARAL REM RAS DAN RENE AA Rion ad BORA ARN Roe BARR RARE 12 Fire Emer Sen y EE ices ed ee Res ase eo hae aie ee ae ee 12 Auxiliary eR Rete in He Ree RAR es 12 Duress Code Entered or Duress Alarm 12 2 CE 12 Alatin Cancel RRE ER EN ER 12 Trouble Indications c ccccccsssceescecsssceescecssecesececsseceseeecsaeceeeeecsaeceeeecsseceeeecsseceeeecsseseeeecseseessecssaeceeeecsuecseeeecsueceetecueseeeescsseseeeeess 13 13 13 Manager C ode 14 WSC Ge ted T 14 14 SWitGhes 14 Area 14 GOTO case ed teenies socks dane tastes sees bade leds se cscs ovens 15 R
32. for additional information Page 9 What Do When You Come Home If you enter your home while the system is armed in the Day Night Delay Away or Vacation mode using an entry door console beeper comes on and beeps 4 times per second The console display indicates DISARM SYSTEM PRESS OFF THEN CODE lights or control modules programmed to come on for the door that you used will do so The system will wait the Entry Delay time You should go to your console and immediately disarm the security system Upon entering the first digit of the user code the console beeper is silenced If canceled or an incorrect code is entered the beeper is restarted If you wish you may go directly to a different security mode rather than disarming the system If you return home and hear the alarm sounding DO NOT ENTER Use a wireless phone or neighbor s phone to call for help What Happens When the Alarm is Activated Burglar Alarm Activated If someone enters through any zone other than an Entry Exit zone if the security system is in the Night or Day Instant mode or if the security system is not turned off during the Entry Delay e The sounder is activated which makes a loud continuous sound The display shows the type of alarm and the zones that have been tripped BURGLAR ALARM ZONE NAME TRIPPED If more than one zone is tripped then the bottom line will show each zone tripped for two seconds Th
33. for an existing program that is being edited or to a default value for a new program For each program it is only necessary to specify the time or event and the action to be taken It is not necessary to specify a condition on the program if the action should be taken whenever the specified time or event occurs Page 57 Programs When Selecting the 1 WHEN key from the Edit Program menu allows the time or button event that activates the program to be changed The display shows EDIT WHEN 1 TIMED 2 BUTTON Times Programs Selecting 1 TIMED sets the program to be activated at a specific time of day You are prompted to enter the time and date or days of week The current default value is shown for each item Press to accept the default 12 00 AM 5 17 1 TIME 2 DATE DAY Select 1 TIME to enter the new time If the desired time is the time in which sunrise or sunset will occur press the up arrow key for sunrise or the down arrow key for sunset before entering a time TIME 12 00 AM HHMM t RISE AM J SET PM You may also choose to have the program execute up to 120 minutes before or after the time of sunrise or sunset SUNSET 1 2 AFTER AT If the 1 2 AFTER key is selected you will be prompted to select the amount of minutes ENTER OFFSET 0 120 MINUTES When entering a time of day AM PM must be specified for the time if the AM PM format is being used Otherwise the entered t
34. motion detectors are armed All zones have an Exit Delay so that you will have time to leave and close the door after you arm the system The system will be fully armed after the Exit Delay There is an Entry Delay on the Entry Exit zones in the Away mode so that you will have time to turn the system off when you return through your door Note that the Entry Delay only applies if you come in through an Entry Exit zone If someone attempts to climb into a window or if an interior zone is tripped before the Entry Exit zone the alarm will be activated immediately If you do enter through an Entry Exit zone first then the other zones are disabled during the Entry Delay in case you have to cross through another zone to get to your console an interior motion detector for example 4 VACATION This mode arms all doors windows and interior motion detectors same as Away mode There is an Entry Delay the Entry Exit zones Use this mode when you are leaving for a period of days 5 DAY INST DAY INSTANT Functions same as Day mode however there is no Entry Delay on any of the security zones There will be an instant alarm if any of the zones are violated while in this mode 6 NIGHT DLY NIGHT DELAY Functions same as Night mode however there is an Entry Delay on the Entry Exit zones Use this mode if you are going to sleep but a family member is expected home at a later time Using Shortcut Keys There are three shortcut keys o
35. of sunrise and sunset each day Sunrise sunset can be specified as the time a scheduling command is executed as an enable disable time or as a darkness condition on a scheduling command or event button To enable the system to properly calculate sunrise and sunset times you must enter your latitude location north or south of the equator longitude location east or west of the Prime Meridian and time zone These items should be set to the proper values for the location where the Omni is installed The latitude and longitude for a particular location may be obtained from an almanac or map of the area These values should be entered to the nearest degree The value entered for the time zone is the number of hours difference between local standard time at the Omni IIe location and Greenwich Mean Time The following values should be used for the standard time zones in North America ZONE NAME ATLANTIC EASTERN CENTRAL MOUNTAIN PACIFIC YUKON ALASKA HAWAII BERING OANA NA The value specified for longitude may be adjusted to correct for areas such as Nova Scotia where the local time differs from Greenwich Mean Time by a non hourly amount The calculated time of sunrise sunset will change by four minutes for every degree change in longitude To cause the calculated sunrise sunset to occur later enter a larger value for longitude Enter a smaller value for longitude to cause the time to occur earlier It is not necessary
36. on a keypad Press key to enter your selection Page 59 Corresponding Switch Table UPB 6 Button Keypad UPB 8 Button Keypad RadioRA Master Control ALC 4 Button On Button Off Button N DA Nn DA BR WO CON A Security Mode Event Buttons Pressing the 2 SEC key allows you to select the event button that will be activated when a security mode changes O OFF 1 DAY 2 NIGHT 3 AWAY 4 VACATION 1 After security mode is selected an additional menu appears which allows you to further specify the event button For example you would like to activate an event button when you arm the system into the 3 AWAY mode WHEN AWAY 1 DELAY 2 CODE 3 AREA Any of these may be selected alone or in combination As each item is specified the menu is redisplayed with the updated event button description Press the key when done Selecting 1 DLY allows the user to specify whether the event button is activated at the start or end of the exit delay WHEN ACTIVATED 1 START EXIT 2 END EXIT When you specify that the event button is activated at the start of the delay by pressing the 1 START EXIT key the mode is prefixed by A for arming into WHEN AWAY END OF DELAY WHEN A AWY START OF DELAY When the system is armed in the Day instant or Night delay mode e
37. plug is provided with this equipment This equipment is designed to be connected to the telephone network or premises wiring using a compliant modular jack which is Part 68 compliant See installation instructions for details 3 REN is useful to determine the quantity of devices you may connect to your telephone line and still have those devices ring when your number is called In most but not all areas the sum of RENs of all devices should not exceed five 5 To be certain of the number of devices you may connect to your line as determined by the REN you should call your telephone company to determine the maximum REN for your calling area 4 If your Omni system causes harm to the telephone network the telephone company may disconnect you service temporarily If possible they will notify you in advance You will be advised of your right to file a complaint with the FCC 5 Your telephone company make changes in it s technical operations facilities equipment or procedures if such changes affect the compatibility or use of this device the telephone company is required to give adequate notice of changes so as to give you an opportunity to maintain uninterrupted service 6 In the event of equipment malfunction all repairs should be made by our company an authorized agent It is the responsibility of users requiring service to report the need for service to our Company or to one of our authorized agents Service c
38. reading should be changing only by two or three counts from its average steady reading When a door or window is opened the reading will go up to a value that represents that zone is open This feature can be used to monitor the quality of the zone wiring and contacts If the numbers begin to deviate from their original values when the system was new wiring problems that will eventually lead to trouble or false alarms may be developing You may wish to record the Status Test values for future reference 5 TEMP TEMPERATURE The Temperature Status menu allows you to view and scroll through the status of each Thermostat PESM and Temperature Sensor To enter the Temperature menu from the Status menu press the 5 key on the console keypad The system will display TSTAT 1 TEMP 80 J HEAT 60 COOL 82 You may enter a unit number to start displaying the status with that unit or simply press the down arrow key to scroll through the list of temperature zones The status display is as shown under Temperature Control except that now the arrow keys may be used to continue scrolling TSTAT 1 MODE AUTO FAN AUTO At this point you may press the key to control the temperature zone as specified under Temperature Control 6 ENERGY ENERGY COST The Energy Cost Status menu allows you to view the current energy rate in use ENERGY COST MID The Energy Cost will display Lo Mid Hi or Crit for critical energy rates Event Log The Event
39. returns to the Edit Program menu Control Unit Switch Press Event Buttons This Event Button is activated upon the following When the specified Unit is turned on or off When the top rocker or bottom rocker is pressed on a UPB RadioRA or ALC switch When a button is pressed on a UPB 6 Button or 8 Button Keypad When a button is pressed on a RadioRA Master Control When a button is pressed on a ALC 4 Button Scene Switch Module Press the 1 CTRL key to select the When Command for a control unit event UNIT ENTER UNIT The unit may be selected by entering the unit number followed by the key or by using arrow keys to scroll through list of unit names Select the desired unit Next you are prompted to specify the event that activates the program WHEN Porch Light O OFF 1 ON 2 SWITCH Press the 0 OFF key to select when the unit turns off or press the 1 ON key to select when the unit turns on this program is executed whenever the unit is turned off or on Press the 2 SWITCH key to select only when the top rocker or bottom rocker is pressed at a UPB RadioRA or ALC Switch locally at the Switch or when a button is pressed on a keypad SWITCH O OFF 1 ON 2 11 SW1 SW10 Press 0 to select only when the bottom rocker off is pressed on the Switch Press 1 to select only when the top rocker on is pressed on the Switch Press 2 9 see the Corresponding Switch Table to select when that button is pressed
40. secure when the system is armed Otherwise the console will beep three times and display ZONE NOT If the system is armed and a zone is open when the Exit Delay expires the alarm will sound The default for Enable Auto Bypass is No All On For Alarm This option will instruct Omni IIe to execute an X 10 All On command in the event that any type of alarm occurs Beep On Trouble If the Omni detects any troubles with itself or one of the zones connected to it it will display a message on the screen and beep the console twice per second continuously i e beep beep beep beep You can silence this sound by pressing the key However if the trouble occurs again the beeper will start beeping again If you do not wish to hear the beeping sound when a trouble occurs set Beep On Trouble to No The default setting for Beep On Trouble is Yes Set up Miscellaneous To configure Miscellaneous items in the system from the Set Up menu press the 6 MISC key High Security Mode In High Security Mode the Master or Manager code is always required to do the following functions Any Control functions Any Temperature Control View the Event Log Access the system from a local phone With High Security Mode Off no code is required to access a local telephone If your system is set up with High Security Mode On the display will request the Master or Manager code whenever you select one of these functions even if the securi
41. the console in Area if you have a Master code or a code that is valid for both areas From the top level display or from the main menu press the 2 SEC key on the console keypad Press the 0 OFF key the display will show DISARM ENTER CODE AREA Press the AREA key the display will show AREA ENTER AREA O ALL 4 The Area number be entered followed by the key or the arrow keys may be used to scroll through a list of areas If the 0 key is pressed then all areas will be selected Press the 2 key then the key You will then be prompted to enter your code The display will show DISARM AREA 2 ENTER CODE Page 14 If the 0 ALL key had been selected display will show DISARM ALL AREAS ENTER CODE AREA As the four digit code is entered X characters are echoed after the ENTER CODE prompt If the Master code or a valid code is entered the console will beep one time and Area 2 will be disarmed Even if Auto Bypass is enabled the system will not arm another area if any zones in that area are not ready If any zone in Area 2 is not ready open after you enter the code the console will beep three times and display AREA 2 on the top line and ZONE NOT READY on the bottom line AREA 2 ZONE NOT READY RETRY In order to arm Area 2 from a console in Area 1 you must first secure or Bypass any zones in AREA 2 that are Not Ready Press key to retry the arming process
42. the telephone within 5 seconds of picking up the phone The Omni will respond with a menu Press 8 on the telephone keypad then 8 The unit will say ADDRESS IS then the Omni will play back the message stored in the Address memory if one has been entered by your installer To record your address Press 9 then enter the Master Code The Omni Ie will say RECORD ADDRESS then BEEP Ina normal tone of voice say your name and address and any helpful information for locating your house THE JONES RESIDENCE 1234 JOHNSON STREET CORNER OF JOHNSON AND THIRD STREET The unit will beep after 8 seconds then play the address back to you If you are not happy with the sound re record by pressing 9 and the Master code If you would like to hear the address again press 8 for Play Address If you accidentally press 9 but have not entered your Master code and do not wish to record a new address simply hang up the phone The address can be recorded from a local in house phone or a remote phone We suggest using a local phone for higher sound quality gt When the Omni says record address beep any previous address recorded on your system is erased Always verify that you have your name and address in your system if you have entered this function gt When recording the address do not press touch tone keys on your phone until the second beep indicating that recording is complete This will cause improper operation when the
43. time should be 13 00 23 59 Next you are then prompted with a question that asks if Daylight Savings Time is currently being observed DAYLIGHT SAVINGS TIME O NO 1 YES Page 54 If Daylight Savings Time is currently being observed between spring and fall set this item to Yes If Daylight Savings Time is not currently being observed between fall and spring or is not observed in your geographic location set this item to No This item is used to correctly calculate the times for sunrise and sunset You are only asked this question when you set the time Once time is set Omni will automatically adjust the time of day each time daylight savings time begins and ends Finally you are prompted to enter the current date ENTER DATE MMDDYY Enter the current date If the current date is February 8 2006 enter it as 0 2 0 8 0 6 Advanced Control Programming ACP Your Omni can be programmed to do automated control and security functions on time schedule or in response to an event occurring in the system You may program the following items Unit Numbers On Off On for time Off for time Dim Brighten Dim for time Brighten for time Level and Scene Settings for HAI Communicating Thermostats PESM control On Off On for time Off for time and Heat and Cool setback temperatures Temperatures Low and High temperatures All lights On All Off Security modes Off Day Night Away Vacation Day Inst
44. to alter the time zone to compensate for daylight savings time the Omni will automatically adjust its calculations for sunrise and sunset and time when daylight savings time begins and ends LATITUDE 30 0 60 1 LATITUDE N S 1 1 NORTH 2 SOUTH 1 LONGITUDE 90 0 180 1 LONGITUDE E W 2 1 EAST 2 WEST 1 TIME ZONE 6 0 12 t TIME ZONE E W 2 1 EAST 2 WEST 1 76 Daylight Savings The Omni automatically calculates the day of daylight savings time each year It also adjusts time of day each time daylight savings time begins and ends To enable the system to properly calculate daylight savings time a start month start weekend end month and end weekend is set up at the factory You may change or disable this function if desired DST START MONTH 4 1 12 O0 DISABLE 1 DST START WEEKEND FIRST SUNDAY CHNG 4 DST END MONTH 10 1 12 O0 DISABLE 1 DST END WEEKEND LAST SUNDAY CHNG Set the value for DST Start and End Months to 0 if Daylight Savings Time does not apply to your region to disable this automatic time update feature The DST Start and End Weekend takes place on the specified Sunday 1 7 at 2 00 AM To change the DST Start or End Weekend press the key then use the arrow keys to scroll through the list Press the key to make the new selection NUMBER DESCRIPTION First Sunday Second Sunday Third Sunday Fourth Sunday Last Sunday Next to Last Sunday
45. unit is displayed press the key For HLC UPB lighting loads the console will display LR Sconce O OFF 1 ON 2 DIM 3 BRT 4 LR Sconce 4 LVL 6 LED 9 TIM STAT Press 0 OFF to turn the selected lighting load off Press 1 ON to turn the selected lighting load on Press 2 DIM to dim the selected unit 1 9 steps each step is 10 from its current level Press 3 BRT to brighten the selected unit 1 9 steps each step is 10 from its current level Press 4 LVL to set the desired lighting level of the selected unit 0 100 VV VV V WV Press 6 LED to turn on or off the LED behind the specified button on a general purpose 8 Button or 6 Button Keypad Specify 1 8 to control the LED behind buttons 1 8 respectively and then select 0 OFF 1 ON gt Press 9 TIM to time the selected unit On Off Dim Brighten e Timed commands may be from 1 99 seconds 1 99 minutes or 1 18 hours gt Press STA to see the exact status of a UPB device When the key is pressed Omni sends a Status Request message to the selected device for its current state The exact state is then displayed LR Sconce STATUS 67 Note When a UPB signal is received over the powerline Omni will automatically update the status of the device Page 22 Controlling CentraLite Units Entry Lights O OFF 1 ON 2 DIM 3 BRT 4 Entry Lights 4 LVL 5 RMP 9 TIM STAT Press 0 OFF to turn the se
46. will disarm normally No sirens will sound no lights will flash but the Omni will perform a silent dial out and say that this is a silent alarm To stop a silent dial out turn your security system off the usual way pressing Off key then your code Panic Switches If you have had panic switches installed they are always armed Pressing a panic switch will cause the alarm to activate This alarm can only be silenced by pressing the Off key and a valid code on the console Area Arming If your installer has enabled the Area feature the security system may be armed in Area 1 and disarmed in Area 2 In fact each area may be armed in different security modes at the same time Each area will have its own console that will control that area independently from the other When disarming the security system or arming the security system in any mode the system will automatically control all security functions in the area of that console if your code is valid for that area If you have a Master code your code is valid in any area If you are in Area 2 and wanted to arm the system in the Away mode simply press the Away key and enter your code The system will automatically arm Area 2 The security mode in Area 1 will not change If you have a code that is only valid in Area 1 you will not be able to disarm or arm Area 2 If you are in Area and wish to disarm the security system in Area 2 Omni will allow you to disarm Area 2 from
47. your static hostname instead of an IP address A client program typically provided by the Dynamic DNS provider runs on a PC on your local network and is used to automatically update your Dynamic DNS provider with your current IP address Several router switch manufacturers have embedded a Dynamic DNS client into their router firmware These devices work with several of the Dynamic DNS providers including both free and commercial services These devices are especially beneficial because the router can be powered up all the time so the dynamic update is always current and is handled by a single device the router switch in the local network This allows you to locate and connect to the Omni controller without having a computer on the local network powered up and running Page 51 10 0 0 231 172 65 10 44 HAI Omni Controller 134421128 10 0 0 230 Cable DSL Modem HAI Omni Ile Controller 210 39 55 13 Router with Internal Dynamic DNS Support 10002 93 110 32 27 E3 10 0 01 To connect to an Omni controller from Computer the Internet using HAI PC Access under Dynamic DNS Server Configure gt gt Network enter the public IP address To connect to an Omni controller on a local network using HAI PC Access ie 134 42 112 8 under Configure gt gt Network enter the controller s IP address i e 10 0 0 230 Local W
48. 6 CONTROL Control Commands The control features of the Omni make it easy and convenient to control almost any light or appliance from the console or over the telephone You may also have your heating and air conditioning HVAC under control of the system which will allow you to save energy dollars by setting the temperature appropriately when you are home asleep or away Furthermore the Omni can be used to program lights to make the home or business look occupied as a deterrent to thieves The methods that the Omni uses to control different devices are UPB switches modules and keypads for lights and appliances CentraLite loads and relays a LiteJet and Elegance lighting system RadioRA switches and dimmers on a Lutron RadioRA lighting system e ALC switch modules for lights and appliances 10 compatible modules X 10 X 10 Pro Leviton PCS ACT Lightolier etc for lights and small appliances HAI Communicating Thermostats for controlling Heating Ventilation and Air Conditioning Systems e Programmable Energy Saver Modules PESM for central heating and air conditioning systems e Direct Output Control for relays to activate sprinklers lighting electric heating etc An Omni will control gt 64 UPB switches modules and keypads up to 8 rooms of HLC Lighting 64 CentraLite loads and relays 64 RadioRA switches and dimmers 62 ALC switch modules 64 X 10 compatible modules four house code
49. 6 Button or 8 Button Keypad Controller each device that has that Link pre configured will respond to its preset levels At this point Omni no longer knows the exact state of the units that responded to the specified Link command until the switch is pressed locally the controller sends a command message to the device or a Status Request message is issued to the device Unit Toggle Command Using HAI PC Access Software you can create programs to toggle any unit 1 128 from its current state to the opposite state When the program is executed the unit will toggle to Off if the unit is currently in a non off state On On for time Level 1 100 Scene A L Dimmed Steps Dimmed for time Brightened Steps or Brightened for time When the program is executed the unit will toggle to On if the unit is currently Off Note If a unit is currently timed On for time Dimmed for time Brightened for time or Off for time when the toggle program is executed the unit will toggle to the opposite state and will defeat the timer This programming feature will simplify programming when using a button on a UPB Compose ALC or RadioRA keypad to toggle a light on and off with the push of a single button For example WHEN FRONT FOYER SW1 PRESSED FRONT FOYER TOGGLE Program Security Commands Press the 2 SECURITY key to arm and disarm the security system or to bypass and restore an individual zone The following menu is displayed O OFF 1 DAY 2
50. 7 48 8F D1 3A EF 70T After the last digit 169 digit has been entered press the key to store PT 2 of the encryption key Page 78 Set Up Names The system can be set up to display descriptive names such as FRONT DOOR JOHN S BEDROOM or PORCH LIGHT for zones units buttons codes temperatures areas and messages These names are displayed instead of the unit zone button code temperature area and message number that is normally displayed Zone and Message names may be up to 15 characters long Each of the other names may be up to 12 characters long To enter the Set Up Names menu from the Setup menu press the 7 NAME key SET UP NAME 1 CTRL 2 ZONE 3 BTTN J 4 CODE 5 TEMP 6 AREA 8 MSG The 6 AREA choice will only be displayed if area arming is being used Select the item that you would like to name by pressing one of the keys 1 6 and 8 The current name for the first item unit zone button code temperature area and message is then displayed Use the arrow keys to scroll through the list of names To enter name enter the two digit code shown in Appendix for each character in name then press the key Use the up arrow key to delete the most recently entered character ZONE 1 00 95 ZONE 1 FRONT DOOR 00 95 T DEL ZONE 1 FRONT DOOR 00 95 Set Up Voice The Omni IIe can be set up to speak descriptive names such as FRONT DOOR for control zones units buttons c
51. AD TRBL Every hour the Omni takes a dynamic test of the battery If the battery voltage is too low then the console will indicate BATTERY LOW If this happens make sure that the battery 15 connected The BATTERY LOW indication will remain until the next battery test is executed hour later or when a Status Test command is given gt COMMUNICATOR TRBL NOW or HAD TRBL Indicated if the digital communicator not the voice dialer was unable to make contact with the Central Station after trying both numbers multiple times If this happens there could be a problem with the system central station or the phone line Call your installer for service gt FUSE TRBL NOW or HAD TRBL Indicated when the solid state fuse that protects the Auxiliary power supply opens The fuse will automatically reset when the fault condition is cleared gt PHONE LINE DEAD TRBL NOW or HAD TRBL Indicated if the phone line is dead for more than 1 minute To silence the trouble beeps the console press key If more than one type of trouble has occurred the display will show each one for two seconds Pressing key will acknowledge all trouble indications If the trouble condition occurs again the console beeper will beep again See Set Up Arming Beep On Trouble if you wish to disable the beeper gt NO CONTROLLER DATA Indicated when console s alarm functions are no longer operational This may indicate a wiring problem to t
52. AREA 2 3 Button Press 3 from the MAIN MENU to get to the BUTTON menu If button voice descriptions have been programmed after a three second delay the system will begin reading from the list of buttons Omni will say the button number then its description User buttons 1 64 are available from the phone for the current area 4 All Press 4 from the MAIN MENU to get to the ALL menu ALL PLEASE CHOOSE 0 ALL OFF 1 ALL ON 2 LIGHT SETTING Leviton Scene 5 Temperature Press 5 from the MAIN MENU to get to the TEMPERATURE menu The Omni will say TEMPERATURE ENTER TEMPERATURE NUMBER THEN POUND After a three second delay the system will begin reading from the list of Thermostats and Energy Savers if voice descriptions have been programmed Omni will say the temperature zone then its description The Omni will read three temperature zones then say PRESS POUND TO CONTINUE If the key is pressed Omni will read the next three temperature zones and descriptions if programmed Page 45 Press the temperature zone you wish to control then press Press the 0 key to select all HAI Thermostats This is a simple way to broadcast the new Heat or Cool setting or change the system mode fan mode or hold mode of all HAI thermostats in your system When an HAI Communicating Thermostat is entered THERMOSTAT 1 THERMOSTAT 1 TEMPERATURE IS PLEASE CHOOSE 1 MODE
53. AT 70 COOL 78 4 Upstairs MODE AUTO FAN AUTO 7 If hold mode is On HOLD is shown Upstairs HOLD MODE AUTO FAN AUTO 1 For a heat or cool thermostat the status shows the current temperature the temperature setpoint whether hold mode is on the system mode and the fan on auto selection Upstairs TEMP 71 HEAT 70 4 Upstairs MODE HEAT FAN AUTO Programmable Energy Saver Modules PESMs The PESM is used when you are have any thermostat other than a HAI Communicating Thermostat and would like to control your heating and cooling system with the Omni system The PESM 15 a temperature sensor and control relay in a small enclosure that mounts near your central heating ventilation and air conditioning HVAC system thermostat The PESM allows the Omni to read the temperature of the area that the HVAC system controls When you are away or asleep the PESM can be set to allow the temperature to drift higher or lower to reduce the operating time hence saving energy dollars The PESM provides an energy saver function When the energy saver is on the HVAC system is set back meaning that the temperature is allowed to rise or fall to an energy saving level When the energy saver is off your thermostat operates normally Your thermostat should be set to the desired comfort temperature Only when the energy saver is on will the temperature be allowed to deviate from your normal thermostat setting There are three temperatures
54. BATTERY TRBL RST The system records each remote access A remote phone access is when someone calls into the system from an outside phone line Remote phone access is also recorded if the system phones out in response to an alarm and the called party enters a code The event log displays the code used to access the system and REM ACCESS 12 05 PM 5 8 USER NAME REM ACCESS An event is logged after three unsuccessful attempts are made to log into the system from a remote phone the Omni will lock out remote telephone access for hour to discourage any further attempts to access the system See Telephone Control Local access of the system using an in house telephone is not recorded The event log will also record each time the PC Access software is used to access the system The event log displays the code used to access the system and PC ACCESS Messages The Message menu is used to show log clear and send text messages and to say and phone dial out your voice messages To enter the Message menu from the top level display or from the main menu press the 8 MESSAGE key on the console MESSAGE 1 SHOW 2 LOG 3 CLEARY 4 SAY 5 PHONE 6 SEND 4 Show Message The 1 SHOW key allows you to display the selected text message s on console s top level display This can a helpful reminder of special events and occasions TRASH NIGHT ENTER MESSAGE 40 You may enter message number followed by the
55. DAYS DIAL OUT 1 OFF TIME DAYS DIAL OUT NUMBER 2 AREA DIAL OUT 2 ON TIME DAYS DIAL OUT 2 OFF TIME DAYS DIAL OUT NUMBER 3 AREA DIAL OUT 3 ON TIME DAYS DIAL OUT 3 OFF TIME DAYS DIAL OUT NUMBER 4 AREA DIAL OUT 4 ON TIME DAYS DIAL OUT 4 OFF TIME DAYS DIAL OUT NUMBER 5 AREA DIAL OUT 5 ON TIME DAYS DIAL OUT 5 OFF TIME DAYS DIAL OUT NUMBER 6 AREA DIAL OUT 6 ON TIME DAYS DIAL OUT 6 OFF TIME DAYS DIAL OUT NUMBER 7 AREA DIAL OUT 7 ON TIME DAYS DIAL OUT 7 OFF TIME DAYS DIAL OUT NUMBER 8 AREA DIAL OUT 8 ON TIME DAYS DIAL OUT 8 OFF TIME DAYS Page 84 INSTRUCTIONS TO CALLED PARTY Dear I have programmed my Omni Home Automation system to call you if my alarm is activated If it is activated it will call and say Emergency Emergency The burglar or fire alarm has been activated at the following address Phone Number Please respond immediately This message will be repeated 2 times At any time during the message please dial my code which is If you make a mistake press then enter the code again This will stop the system from making any further calls The system will tell you what zone caused the alarm Press 9 The system will say Good bye and hang up Hang up then call me at If no one answers please hang up then call the police fire or emergency departments NOTE IF THE SYSTEM SAYS THIS IS A SILENT ALARM please call the p
56. Duress Code Entered or Duress Alarm Activated See Duress Code for a description of when to use In the event that you enter your duress code or a Duress zone is tripped the system performs a silent dial out as follows Noalarms lights or console beepers are activated The system does not display the duress alarm e The system waits the Dial Out Delay and then begins to dial out If you are having your system monitored the central station will be sent a code representing a silent alarm duress Alarm Reset The alarm system will reset itself and turn off the sirens after the system has been in alarm for the configured Alarm Reset time window between 6 30 minutes When the alarm system resets any zone that is ready is reactivated so the alarm system will be activated again if the zone is tripped If a zone remains not ready i e a door has been left open it will be automatically bypassed when the alarm resets Alarm Cancel At any time you can disarm and silence an alarm by pressing the Off key and entering your code If the alarm is disarmed after the Dial Out Delay but within the Alarm Reset window the communicator will send the alarm code followed by a code indicating that the user has canceled the alarm and the console will display ALARM CANCEL If an alarm is disarmed before the Dial Out Delay has expired the system will not report anything to the central station and the console will display ALARM ABORTED If
57. HNG The times and days are changed by pressing key Choose the 1 TIME key to change the On or Off times You will be prompted to enter the new time AM PM must be specified for the time if the AM PM format is being used otherwise the entered time should be 13 00 23 59 Each item defaults to its current value Press the up arrow key to select Sunrise and press the down arrow key to select Sunset CODE 2 ON OFF TIME 1 TIME 2 DAYS TIME 8 00 AM HHMM tT RISE AM J SET PM To change days press key then press the 2 DAYS key You will be prompted to enter the day s that the code will be valid Press 1 7 for Monday Sunday 0 for Never 8 for Weekdays and 9 for Weekends DAY S MIWTFSS 1 7 MON SUN O NEVER Duress Code If you are forced to disarm the system against your will by an intruder disarm it as you normally would but use the Duress Code instead of your normal code The system will disarm normally No sirens will sound no lights will flash but the Omni Ie will perform a silent dial out and say that this is a silent alarm To stop a silent dial out turn your security system off by pressing OFF then your code DURESS CODE 0000 9999 0000 DISABLET Set Up Time To set up time and date from the Setup menu press the 2 TIME key TIME J PM You will be prompted to enter the new time and date AM PM must be specified for the time if that format is being used otherwise the entered
58. K DETECTED DETECTOR DEVICE DIAL DIGIT DIMMER DINING DISABLE DISARMED DOCK DOG DOOR DOWN DRAPES DRAWER DRESSING DRIVEWAY DURESS DVD EAST ECONOMY EIGHT EIGHTEEN EIGHTY ELEVATOR ELEVEN EMERGENCY NABLE NERGY NTER NTERING NTERTAINMENT ENTRY EQUIPMENT EVENING EVENTS EXECUTIVE EXERCISE EXIT EXTENSION CODE 214 215 216 341 80 81 342 343 344 217 5 17 218 345 82 219 16 346 347 220 221 348 15 349 350 14 4 83 84 351 352 353 85 354 355 222 86 223 356 87 357 88 224 89 90 358 92 359 91 360 361 362 363 364 93 94 365 95 96 366 DESCRIPTION EXTERIOR FACTORY FAILURE FALL FAMILY FAN FATHER S FAULT FEBRUARY FENCE FIFTEEN FIFTY FILE FILTER FIRE FIRST FIVE FLAG FLOOD FLOOR FLOW FORCE FORTY FOUNDATION FOUNTAIN FOUR FOURTEEN FOYER FREEZE FREEZER FRIDAY FROM FRONT FULL FUNCTION FURNACE FUSE GALLERY GAME GARAGE GARDEN GAS GATE GIRL S GLASS GO GO TO GOOD GOOD BYE GOT GREAT GROUNDS GROUP GUARD GUEST GUN GYM HAD HALL HAPPY CODE 367 368 97 369 370 98 371 372 DESCRIPTION HARBOR HAVE HEAT HELLO HELP HIGH HIGHER HOBBY HOLD HOLIDAY HOME HOT HOURS HOUSE HUMIDITY HUNDRED IMMEDIATELY IN NCREASE NFRARED NPUT NSIDE NSTANT NTERIOR NTERNET NTRUSION INVALID IS JACUZZI JANUARY JEWELRY JULY JUNE KEEPER KENNEL KEY KITCHEN LAMP LANAI LAND LAND
59. LC Room 5 and 6 UPB Unit ID 33 48 CentraLite loads 33 48 RadioRA Lighting Zones and Master Controls 33 48 or X 10 modules 1 16 House Code 2 49 64 HLC Room 7 and 8 UPB Unit ID 49 64 CentraLite loads 49 64 RadioRA Lighting Zones and Master Controls 49 64 or X 10 modules 1 16 House Code X 3 33 63 ALC addresses 1 31 Branch 2 65 72 Voltage Outputs 1 8 Fully Configurable 73 128 Internal Flags X Represents the House Code setting on the Omni Controller Tfused Scrolling Through Names The Omni stores names for Units Zones Buttons Codes Temperatures and Messages so that you don t have to remember that UNIT 5 is the DEN LIGHT and ZONE 1 is the FRONT DOOR In general any time you enter a unit zone button code temperature or message number you can press the down arrow key to display its name then use the up and down arrow keys to scroll through the list of other names This is true when entering commands and programming on the console Only named items are displayed on an OmniTouch touchscreen Controlling Units The control menu is used when controlling lights and appliances To enter the control menu from the top level display or from the main menu press the 1 CTRL key on the console keypad Omni will automatically display the first named item in that list The down arrow key can then be used to scroll through the list and key is used to select the ite
60. LLITE SATURDAY SAUNA SAVER SCENE SCHOOL SCREEN SECOND SECONDS SECURE SECURITY SEND SENSOR SEPTEMBER SERVICE SET SETTING SEVEN SEVENTEEN SEVENTY SEWING SHADES SHED SHOCK SHOP SHOW SHUTTERS SIDE SILENT SIX SIXTEEN SIXTY SKYLIGHT SLIDING SMART SMOKE SNOW SOUTH SPA SPARE SPOT SPRING SPRINKLER STABLE STAIRS STAIRWELL STAR STATION STATUS Page 89 DESCRIPTION STEPS STOCK STORAGE STORE STUDIO STUDY SUITE SUMMER SUMP SUN SUNDAY SWITCH SYSTEM OK TABLE TALK TAMPER TAPE TEEN TELLER TEMPERATURE TEMPORARY TEN TENANT THANK YOU THEATER THEN THERMOSTAT THIRD THIRTEEN THIRTY THREE THURSDAY TIME TIMED TIMER TO TOOL TOP TOUCHSCREEN TRACK TRANSMITTER TRAP TRASH TREE TRIPPED TROUBLE TUB TUESDAY TUNER TV TWELVE TWENTY TWO TYPE UNDER UNIT UP UPPER USER UTILITY CODE 186 249 535 250 536 537 538 539 540 DESCRIPTION VACATION VALVE VANITY VAULT VCR VIDEO VISITOR VOLUME WAITING CODE 541 542 251 543 187 544 28 545 188 DESCRIPTION WALK WALKWAY WAREHOUSE WARNING WATER WEDNESDAY WELCOME TO OMNI WELCOME WEST Page 90 CODE 189 546 252 547 548 549 253 550 190 DESCRIPTION WINDOW WINE WING WINTER WOOD WORK YARD YOU ZONE NOTE TO INSTALLER Following installation this manual shall be left for the homeowner s use OMNI AUTOMATION HAI New Orleans LA USA
61. NIGHT 3 AWAY 4 VACATION 5 DAY INST 6 NIGHT 8 BYPASS 9 RESTORE 1 Page 65 Select 0 6 to arm system into desired mode select 8 key to Bypass and 9 key to Restore a security zone If area arming is being used the display will then prompt you for the area to be armed AREA ENTER AREA O ALL 4 Enter the area number followed by the key or use the arrow keys to scroll through list of areas Press the key first to specify all areas Program Button Commands Select the 3 BUTTON key to program a macro button Specify the macro button to be executed See Button Programs BUTTON ENTER BUTTON MENU 4 Program On All Off Commands Select the 4 ALL key to program All Lights On and All Units Off commands It is also used to program Leviton Scenes UPB Link RadioRA Phantom Button or CentraLite Scene ALL O OFF 1 ON 2 SCN 3 LINKY ALL 4 PHANTOM 5 CENLIT t If area arming is being used the display will then prompt you for the area to control Enter the area number followed by key or use the arrow keys to scroll through a list of areas Press the key first to specify all areas Program Video Commands This program command is used to display video automatically on an OmniTouch with Video touchscreen when an event occurs You can specify which camera and which touchscreen s will display the video when the event takes place When the event takes place it switches e
62. SCAPE LASER DISK LAST LAUNCH LAUNDRY LAWN LEAK LEAVE LEFT LEVEL LIBRARY LIFT LIGHT LIGHTING LIGHTS LISTEN LIVE LIVING LOADING LOBBY Page 88 99 DESCRIPTION LOCK LOFT LOW LOWER MACHINE MAID S MAIL MAIN MANAGEMENT MANAGER MARCH MASTER MAT MAY MECHANICAL MEDICAL MEDICATION MEETING MENU MESSAGE METER MID MIDDLE MIDNIGHT MINUS MINUTES MOBILE MODE MODEM MODULE MONDAY MONITOR MONTH MORNING MOTHER S MOTION MOVIE MUD MUSIC MUTE NANNY NEXT NIGHT NINE NINETEEN NINETY NO NOOK NOON NORTH NOT NOVEMBER NOW NUMBER NURSERY NURSE S CODE 128 129 130 444 445 233 446 131 447 448 132 133 449 450 234 235 134 451 452 453 454 135 455 136 137 456 457 138 458 459 460 461 139 140 462 141 142 143 144 463 464 145 465 146 466 467 468 147 469 470 471 472 148 236 149 473 474 150 151 DESCRIPTION OVERFLOW OVERHEAD P M PANIC PANTRY PARKING PARLOR PARTY PATIO PAUSE PC PERIMETER PERSONNEL PET PHONE PHRASE PIER PLACE PLANTS PLAY PLEASE CHOOSE PLUS POINT POLICE POOL PORCH POSITION POT POUND PRECIOUS PRESS PRESSURE PROGRAM PROTECTED PUMP QUARTERS RAIN RAISE READING READY REAR RECORD RECREATION RECYCLE REMOTE REPEAT DESCRIPTION RESIDENCE RESTORE RESTRICTED RIGHT RISE ROMANTIC ROOF ROOM RUN SAFE SAFETY SATE
63. Third from Last Sunday gt Controller IP Address The controller s local network IP address is used to identify the Omni controller on the network To view and assign the controller s local network IP address from the Set Up menu press the 6 MISC key Using the down arrow key 4 scroll to the following menu item IP ADDRESS 192 168 0 101 1 The format of IP address is a 32 bit numeric address written as four numbers separated by periods An IP address has two components the network address and the host address The first two numbers e g 192 168 represent the Class B network address and must be the same as the first two numbers of your local network The second two numbers e g 0 101 identify a particular host on the local network and may be assigned at random as long as each device on the local network has a unique address Each number can be 0 to 255 Enter the 1 2 or 3 digit number followed by the key to move to the next number After the 4 number has been entered press the key to store the IP address Page 77 Controller Port Number The controller s local network port number identifies the logical channel to the Omni controller For example port 80 is used for HTTP traffic the controller s local network port number is used for Omni Link traffic To view and assign the controller s local network port number from the previous Setup item IP ADDRESS press the
64. a Unit To see the status of a unit from the control menu press key The last command along with any time hh mm ss remaining on a timed command will be displayed Entry Lights 1 22 10 STATUS ON At this point one of the menu choices may be entered or or key may be pressed to redisplay the menu Note If an X 10 signal is received over the powerline Omni will automatically update the status of the X 10 unit Internal Flags The easiest way to define a flag it to refer to it as a virtual relay A flag can be in one of three separate states On Off or set to a value between 0 and 255 flag has a value of 1 255 it is considered On flag has a value of 0 it is considered Off Flags are a powerful programming tool that can be used in several ways to accomplish advanced programming routines Any Flag can also be used as a counter Counters can be incremented decremented or set to a specific value 0 to 255 When a counter is decremented to zero the When Unit Off macro is executed A counter will not decrement below zero The counter will however roll over from 255 to 0 when incremented The When Unit Off macro will be executed when the counter rolls over This allows two counters to be cascaded to form a larger counter Page 25 When counter is incremented from 0 to 1 When Unit On macro will now execute This will allow you to execute a command when the Flag is incremented coun
65. a series of commands when it is pressed Buttons are used to program functions that are specific to your home and lifestyle Using a button you can activate several commands at once You can personalize 64 buttons with descriptive names The following are some examples of programmed Buttons Leave for Work Button 1 turn off all lights set thermostat to energy saving settings arm the security system in the Away mode Go to Bed Button 2 turn off all lights dim outdoor lights 20 to extend bulb life and reduce consumption arm security in Night mode Dinner for Two Button 3 dim the dining and living room lights turn on the porch light turn off all the bedroom lights dim the den light turn on the stereo To activate a preprogrammed button from the top level display or from the main menu press the 3 BTTN key on the console keypad Select the button macro to be activated by using the arrow keys to scroll through a list of buttons followed For extra convenience event buttons are automatically activated when you change security modes or when security zones open and close This powerful feature allows you to set your system up so that control functions are performed when you arm your security system such as turning off all lights and setting back the HVAC system Door contacts and motion detectors can be used to turn on lighting automatically then turn it off a few minutes after the person has left
66. acated Premises When Unvacated Premises is set to Yes if the alarm is armed in Away or Vacation mode and no exit zone is violated during the exit delay i e the premises was not vacated the system will automatically arm to Day mode at the expiration of the exit delay To configure Unvacated Premises from the Set Up menu press the 5 ARM key UNVACATED PREM 1 0 1 YES 1 The default setting for Unvacated Premises is Yes Entry Exit Chime When Entry Exit Chime is set to Yes the console s will beep once when a door on an entry exit zone is opened even if the alarm system is off This lets you know when someone enters and leaves The default setting for Entry Exit Chime is Yes Perimeter Chime When Perimeter Chime is set to Yes the console s will beep once when a window or any other perimeter zone is opened even if the alarm system is off The default setting for Perimeter Chime is Yes Enable Quick Arm The Quick Arm feature allows the security system to be armed by pressing the desired mode key twice instead of having to enter your code The default setting for Enable Quick Arm is No Page 72 Enable Auto Bypass The Auto Bypass feature allows the system to automatically bypass an open zone when the system is armed rather than setting off the alarm In some applications it may be preferable to allow arming only if all zones are secure READY With Auto Bypass set to No all zones to be armed must be
67. ach of the specified touchscreens to full screen video This item can only be programmed via PC Access Program Temperature Commands Select the 5 TEMP key to control HAI Communicating Thermostats energy saver modules and temperature sensors Specify the desired command See Temperature TEMPERATURE ENTER TEMP ZONE 0 4 Program Energy Cost Select the 6 ENERGY key to command the energy cost rate Specify the desired energy cost rate ENERGY COST 10 1 MID 2 HI 3 CRIT Page 66 Program Message Commands Select the 8 MESSAGE key to show log clear say phone or send a message Specify the desired command See Message MESSAGE 1 SHOW 2 LOG 3 CLEARY 4 SAY 5 PHONE 6 SEND t The 1 SHOW key allows you to display the selected text message s on console s top level display This can be a helpful reminder of special events and occasions The 2 LOG key allows you to store the selected text message s in the Event Log This can be a helpful to keep track of the times and dates of events and occurrences The 3 CLEAR key allows you to clear the selected text message or all text messages from the console s display The 4 SAY key allows the controller to say the selected voice message over a speaker This voice message can be an audible reminder of special events and occasions i e Front Door Open when the front door is opened The 5 PHONE key allows the controller to call the selected phone number
68. an be obtained at HAI 4330 Michoud Blvd New Orleans LA 70129 7 This equipment may not be used on coin service provided by the telephone company Connection to party lines is subject to state tariffs Contact your state public utility commission or CORPORATION commission for information 8 This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference including interference that may cause undesired operation Part 15 of FCC Rules are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient the receiving antenna 2 Plug the receiver into a different outlet If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions Page 82 CANADIAN INDUSTRY CANADA NOTICE Notice The Industry Canada label identif
69. and say the selected voice message The 4 SEND key allows you to send any a text messages through the Pro Link serial port Edit Program Condition Selecting the 3 amp COND key from Edit Program menu allows the condition for the program to be specified The condition is optional in all program lines This condition must be true when the program time or event occurs for the program to executed Note Two 2 conditions can be specified in each program line however when programming from the console only 1 condition can be selected If 2 conditions must be specified for a single program line it must be entered using the PC Access Software When 2 conditions are part of a single program the conditions are not displayed on the console Instead amp MULTI is displayed to let you know that this program line contains 2 conditions To view or edit the program you must use the PC Access Software The following menu is displayed SELECT CONDITION 1 CTRL 2 SEC 3 ZONE 4 9 TIME MISC After the condition is specified the display returns to the Edit Program menu Program Control Conditions Press the 1 CTRL key to specify that the program should only execute if a specified control unit is either On or Off The display prompts for the unit number UNIT ENTER UNIT Enter unit number followed by the key or use arrow keys to select the unit Page 67 The unit is displayed and the display prompts for sta
70. and then only if it s dark Temperature Control Your Omni can control temperatures of your heating and cooling system monitor the outside temperature and detect high and low temperatures in special situations Other appliances can be controlled by temperature as well such as a bathroom heater or a ceiling fan The temperature menu is used to control HAI Communicating Thermostats Programmable Energy Saver Modules and Temperature Sensors The status of each of these may also be displayed on the console HAI Communicating Thermostats and the Programmable Energy Saver Module PESM provides energy savings comfort and convenience by setting the HVAC system s to the proper temperature based on whether you are home asleep away or vacation The temperature can be reported as well as controlled over any telephone A freeze alarm feature will cause a dial out if the temperature falls below a preset level The HAI Communicating Thermostats are digital heating and cooling thermostats that can be controlled be the user and by remote control There are models for conventional single stage gas or electric heat pumps and multi stage heating and cooling systems All models offer programmability stand alone operation and robust communication to the Omni system Page 30 HAI RC Series Thermostats The following control actions are allowed for HAI Communicating Thermostats Set heating setpoints Set cooling setpoints Set system mod
71. ands when a button is pressed on a switch or on a keypad controller to activate controller macros Send Status Request messages to switches to update their status in the controller Receive the UPB Acknowledgement pulse that indicates that a switch has properly executed a command VVVVVV VV HAI Lighting Control HLC Format HAI Lighting Control HLC combines HAI UPB Wall Switches Dimmers and Modules HAI UPB Room Controllers and HAI UPB House Controllers to create lighting scenes that set the proper mood and ambiance for various activities HLC format is a defined structure for configuring programming and operating all the HLC lighting devices in your home Each House Code that is configured to use the HLC format consists of 2 rooms with up to 8 HLC devices in each room Omni supports up to 8 rooms of HLC lighting Omni can control up to 64 HLC devices HAI manufactured UPB devices collectively referred to as HLC devices can be configured using an Omni console or OmniTouch touchscreen connected to the Omni controller Other UPB devices may be used in the HLC structure but cannot be configured using the Omni controller they must be configured using a PC running UPB UPStart configuration software see Configuring HLC Devices About Rooms Each room of HLC lighting consists of 8 consecutive unit numbers starting at Unit 1 i e Room 1 Units 1 8 Room 2 Units 9 16 Room 3 U
72. ant and Night Delay and bypass and restore zones Buttons Events Messages Show Log Clear Say Phone and Send The Omni executes programs Once at a certain time on a certain date One Time Program On a certain date every year Yearly Program Repeatedly Repeating Programs In response to an event Button Programs You can also specify 2 conditions in each program so that they only run under certain circumstances Every line of programming in the Omni controller consists of three pieces Each line must have at least an event when and a result command The statement condition is optional in all programming lines The program may specify up to 2 conditions that must be true for the program to execute When programming from the console only 1 condition can be selected If 2 conditions must be specified for a single program line it must be entered using the PC Access Software Each program can be set up to execute at a certain time of day or on the occurrence of a particular event in the system When this time or event occurs the programmed action will be taken if and only if the specified condition s is also true at that time The Program menu allows you to add review change and delete automation programs To enter the Program menu from the Setup menu press the 3 PROG key SET UP PROGRAMS 1 ADD 2 SHOW 3 DELETE Page 55 1 Add Programs The 1 ADD key is used to add new automation program
73. arm using the OFF DAY NIGHT or AWAY keys Arming the Security System Now that you know how to disarm the system here s how to arm the security system The security menu is used to arm and disarm the security system To enter the security menu from the top level display press the 2 key on the console keypad The console should display O OFF 1 DAY 2 NIGHT 3 AWAY 4 VACATION 5 DAY INST 6 NIGHT DLY 8 BYPASS 9 RESTORE 7 0 OFF The OFF key disarms the security system resets the fire and emergency alarms and silences all sirens and sounders 1 DAY The DAY mode is intended for use when someone will occupy the house or business that is being protected In the Day mode the perimeter zones doors and windows are armed however interior motion detectors and interior traps are not armed so that you may move about freely inside In the Day mode there will be an Entry Delay on the Entry Exit zone so that someone arriving can turn off the alarm before it sounds Page 6 2 NIGHT The NIGHT mode is used when you are asleep and everyone in your household is at home In the Night mode your doors windows and non sleeping area i e downstairs motion detectors are armed In the Night mode there is no entry delay The alarm system sounder will be activated immediately if any door window or non sleeping area motion detector is tripped 3 AWAY Use the AWAY mode when you leave your house and no one is home All doors windows and
74. associated with each PESM Temperature this is the air temperature read by the PESM Heat temperature the air temperature will be allowed to fall to this temperature when the energy saver is on Cool temperature the air temperature will be allowed to rise to this temperature when the energy saver is on Page 32 The following control actions are allowed on PESMs Turn Energy Saver On and Off Turn Energy Saver On and Off for a specified time Set heating setpoint Set cooling setpoint You can turn the energy saver on off use a timed on off and change the Heat and Cool temperatures from the console or by telephone Commands can also be programmed so that they occur by time schedule or by event such as security mode change For example the system can be set up to turn the energy saver s On and make the Heat setback temperature 65 degrees and the Cool setback temperature 80 degrees when the alarm system is put in the Away mode Another program can turn the energy saver s off to resume normal operation of the HVAC system at 4 30 P M on weekdays to make the house comfortable before arriving home Different setback temperatures could be set for the Night mode To set up your thermostat for use with the energy saver set it in the appropriate mode and set the temperature to your preference NOTE Your heating and cooling system will always be off if you set your thermostat to Off mode The PESM cannot turn it back on The PESM cannot mak
75. ay actively be connected and communicating with the controller simultaneously over the Ethernet port Controller Address Port Number and Encryption Key The controller s local IP address and port number set the local network parameters for the Omni controller The encryption key is used to establish a private secure connection with the connected device These Setup items can only be assigned and changed from an HAI console These items can not be assigned or changed via PC Access although the IP address and port number may be viewed via PC Access See Set Up Miscellaneous Omni Ethernet Connections Use a standard network cable to connect the controller to a hub switch or router Use a network crossover cable when connecting the controller directly to the NIC card on a computer When connected to a switch or router port forwarding must be configured Port forwarding sets up public services on your network The Omni controller listens for all IP UDP communications addressed to it on the specified UDP port number The router will forward all communications on the specified port to the Omni controller Connecting to Network via PC Access To access the controller over the network via PC Access 1 Open an Omni account file 2 Click Configure gt gt Network gt If you are connecting from the local network enter the controller s IP address under Network IP Address or Domain Name gt If you
76. be configured using an Omni controller Other UPB devices may be used but cannot be configured using the Omni controller they must be configured using a PC running the UPB UPStart configuration software Configuring HLC Devices HLC devices can be configured using an Omni console or OmniTouch touchscreen connected to the Omni controller When configuring HLC devices the following information is programmed into the HLC device Network ID UPB Network ID configured in Omni controller Network Name HAI Lighting Unit ID Unit Number of respective unit Unit Name which is the name description given to the respective unit in the Omni controller Room Name using HLC the name of the first unit in the respective group is used otherwise the room number is used Links every device in each room is programmed with 6 consecutive Links starting with Link 1 for example every device in Room 1 is programmed with Links 1 6 Room 2 is programmed with links 7 12 etc Other configuration information Vv When configuring HLC devices using an Omni console or OmniTouch touchscreen each device unit number must first be assigned a name in the Omni controller HAI recommends that you first configure your Omni controller naming all of the HLC units using the HAI PC Access Software and then download the information to the Omni controller Configuring HLC Devices using an Omni Console To conf
77. ce message over a speaker This voice message can be an audible reminder of special events and occasions You may enter the message number followed by key to say that message or simply press the down arrow key to scroll through a list of messages Press the key to say the selected message Phone Message The 5 PHONE key allows the controller to call the selected phone number and say the selected voice message PHONE NUMBER 1 8 Select a phone number 1 8 from the dial menu then press SECURITY OFF ENTER MESSAGE You may enter the message number followed by key or simply press down arrow key to scroll through list of messages Press the key to dial the number and say the selected voice message Send Message Pro Link The 6 SEND key allows you to send any of the text messages through the Pro Link serial port You are first prompted to specify the desired serial port SERIAL PORT 1 4 Page 41 The built in serial ports 71 13 the controller are assigned to Serial Port 1 Serial Port 3 respectively Serial port 4 is a Serial Interface Module connected to the Expansion port on the controller Next select the message to be sent You may enter the message number followed by the key to send that message or simply press the down arrow key to scroll through a list of messages Press key to send the selected message MSGNAME ENTER MESSAGE The message is sent o
78. ce the beeper press the key For more information see Trouble Indications Page 4 Confirmation When you have successfully completed a function such as entering a program or changing a setup item console will once Cancel If you are ever unsure and wish to return to the top level display press the key You may have to press it more than once depending on how far into the function menu you are Each time you cancel out of an operation the console will beep once to indicate that you have canceled The key can also be used if you make a mistake while entering a number For example if you enter 2 when you meant to enter a 3 press key to start over Time Out If you are called away from the console for any reason to take a phone call for instance while you are engaged in an operation the console will time out and cancel it for you after 3 minutes The display will return to the normal top level display Areas If there is an area or a separate building that needs to be protected your installer can divide your Omni system into two independent security systems Area and Area 2 Each area has complete access to all of the capabilities of the Omni yet the Omni can protect each area individually You may decide to use the Area feature if you have a guesthouse or workshop that you would like to have protected separately from your home or maybe you have a bus
79. cryption 50 Omn tans eaters Met eis a Golesi 50 Connecting to Network via PE ACCESS eee 50 Dynamic DNs rash keke tee uaa eaten ee is MO eee eR OG AE eG eat 51 Configuration and Advanced Control Programming 53 Set UP 53 ances ed ws cs TE 53 AUTHORITY teste ena E E lens desea eee 53 1 Ma Stet 53 2 53 E E E E ab Soe eaten STS Gs ot rt one 53 ACCESS E E EEEN V E E 54 DTE SA AE E AEE EE T AEE E 54 Set Up ee acs O ee eee 54 Advanced Control Programming eee ete ES 55 T Programs E ee ee es A 56 Z Show PLO Stas E ages 56 Delete All Programs es ee OS 57 Edit Progranniss earna nni E EE E e ae eE EE ee SE e EEE ETES
80. d on Scene events will be activated whenever the selected device is set to the specified scene On events will also be activated whenever the selected device is set to a scene other than off Miscellaneous Event Buttons Pressing the 7 MISC key allows you to select an event button from a list of other event buttons You are first prompted to select the event button SELECT BUTTON WHEN PHONE DEAD 4 The arrow keys are used to select from a list of event buttons When a camera input 1 6 is pressed on an OmniTouch with Video WHEN ENERGY 10 WHEN ENERGY MID WHEN ENERGY HI WHEN ENERGY CRIT WHEN PHONE DEAD WHEN PHONE RING WHEN PHONE OFFHK WHEN PHONE ONHOOK WHEN AC PWR OFF WHEN AC PWR ON WHEN BATTERY LOW WHEN BATTERY OK WHEN DCM FAIL WHEN DCM OK WHEN CAMERA 1 6 Message Event Buttons Pro Link Pressing the 8 MSG key allows you to select an event button from a list of the 64 text messages You are first prompted to select the message MESSAGE ENTER MESSAGE 4 The message may be entered by entering the message number followed by key or by using the arrow keys to scroll through the list of messages Page 63 Pro Link also has capability to monitor serial port for incoming text messages When text message is received Pro Link searches through all 64 text messages for a matching message If one is found the When Message Received event button corresponding to the matching me
81. e AWAY key is used to arm the security system in the Away mode In the Away mode all zones doors windows motions etc are armed There is an entry delay on entry exit zones so that you can disarm the system when you return through the door 5 Down Arrow The Down Arrow key is used to scroll through menus and lists The down arrow is used to scroll down the list from first to last for example when the first program is being displayed pressing the down arrow will cause the next program to be displayed Page 2 6 UP ARROW The Up Arrow key is used to scroll through menus and lists The Up Arrow is used to scroll back through a list for example if you have already used the down arrow to scroll to an item the Up Arrow will bring you back to a previous item 7 CONSOLE LED The Console LED is used to indicate whether the security system is currently armed or disarmed If armed in any security mode the LED is set to red If the system is disarmed the LED is set to green The LED flashes when a Message is displayed 8 CONSOLE DISPLAY The Console Display is used to show the current security mode and to give useful information that will guide you through normal operations of your Omni control and security system 9 CONSOLE KEYPAD The Console Keypad is used to enter user codes for arming disarming bypassing and restoring zones In some cases the keys 0 9 are assigned to different functions From the top level display
82. e Off Heat Cool Auto Set fan On Auto Turn hold On and Off NOTE Not all actions are applicable to every type of thermostat To enter the temperature menu from the top level display or from the main menu press the 5 TEMP key on the console keypad You will be prompted with the first named temperature zone i e Upstairs The temperature zone can be specified by entering the temperature zone number followed by key by pressing the arrow keys to scroll through the list of temperature zones Press the key when the desired temperature zone is shown Press the 0 key to select all HAI Thermostats This 15 a simple way to broadcast the new Heat or Cool setting or change the system mode fan mode or hold mode of all HAI thermostats in your system Temperature zones 1 4 are for HAI thermostats TEMPERATURE ENTER TEMP ZONE O ALL 4 After the key is pressed a menu appropriate for the type of temperature zone is shown For Celsius temperatures press the key prior to entering the temperature to make the number negative The Celsius temperature may also be specified in 0 5 degree steps if three numeric digits are entered The third digit adds a 5 to the first two digits if it is anything other than zero Enter a leading zero if necessary For HAI heat cool thermostats Upstairs 1 MODE 2 HEAT 3 COOL Upstairs 4 FAN 5 HOLD STAT T To change the system mode on a thermostat press 1 MODE A menu pr
83. e 23 Press 0 OFF to turn selected unit off Press 1 ON to turn the selected unit on Press 2 DIM to dim the selected unit 1 9 steps each step is 10 from its current level Press 3 BRT to brighten the selected unit 1 9 steps each step is 10 from its current level Press 4 LVL to set the desired lighting level of the selected unit 0 100 VV VV V WV Press 5 RMP to ramp the lighting level of an ALC Dimmer Switch to a new level at a selectable ramp rate 5 RMP does not affect X 10 units gt Press 9 TIM to time the selected unit On or Off Timed commands may be from 1 99 seconds 1 99 minutes 1 18 hours gt Press STA to view the current status of the unit Ramp Command ALC When ALC Switch Modules are being used it is possible to ramp the lighting level of an ALC Dimmer Switch to a new level at a selectable ramp rate Only ALC Dimmer Switches respond to the Ramp command Press the 5 RAMP key to select the ramp command The keypad will then prompt you for the desired ramp rate ENTER RATE MINUTES 1 99 H M S The rate specifies the time it takes the switch to go from full off to full on or from full on to full off Thus a level change from full off to 50 on will take half the time specified Before any digits are entered the key may be used to switch between specifying the rate in minutes seconds and hours After you choose between minutes seconds and hours enter the rate
84. e When Alarm macro is activated Any units programmed to come on will do so The Flash For Alarm Unit Number begins to flash on and off system waits the Outside Siren Delay 0 60 seconds then activates the sounder If enabled the system waits the Dial Out Delay 15 45 seconds and then if programmed the in house phones are seized disconnected and the Omni begins to dial out If you are having your system monitored by a central station the central station will be sent a code representing the type of alarm burglary and zone involved In most cases the central station will call back requesting your password or passcode If you are not using central station monitoring but are using the voice dial out capability the system looks at the Dial Order to determine which number to call first and calls that number If you are using both central station monitoring and voice dial out then the voice dial out is delayed by five minutes to give the central station time to call you back For more information on the digital and voice dialer See Digital Dialer and Voice Dialer e system continues to sound all alarms and sirens and flash light s for the 6 30 minute Alarm Reset window After Alarm Reset window has expired the sounders are turned off and the alarm system is reset The console beeper stays on zone is tripped after a reset the alarm will again be activated and the dialer will again dial out
85. e auto bypass is recorded in the event log as ZONE NAME BYPASSED To prevent any zone from being bypassed unintentionally you should always look for SYSTEM OK on the display before arming and leaving the premises The Auto Bypass feature can be disabled if you do not want the system to automatically bypass open zones If the auto bypass feature is disabled the alarm will sound if a zone not ready i e open when the system is armed NOTE The Auto Bypass feature is disabled on UL Listed Installations Restoring Zones 9 RESTORE Restoring a zone puts it back on active duty in the system When restored the Bypassed indication will no longer be displayed on the status line and the zone will be checked for alarms To restore a zone from the top level display press 2 on the console keypad then 9 for restore Enter the zone number followed by the key or use the arrow keys to select the zone Press 0 as the first key to restore all zones The 0 ALL choice is removed once a digit key or the down arrow is pressed After the zone or all zones is entered you will be prompted to enter your code The console will beep and the display will return to the top level display GOTO To Bypass or Restore a zone in another area you must first go to that area by selecting GOTO AREA ENTER AREA At this point you may enter the area number followed by the key or use the down arrow key to scroll to the next area See Area Arming
86. e your system cool below the thermostat s cool setting or heat above the thermostat s heat setting Control actions for temperature sensors low setpoint high setpoint To enter the temperature menu from the top level display or from the main menu press the 5 TEMP key on the console keypad You will be prompted with the first named temperature zone i e Upstairs The temperature zone can be specified by entering the temperature zone number followed by key or by pressing the arrow keys to scroll through the list of temperature zones Press the key when the desired temperature zone is shown TEMPERATURE ZONE ENTER TEMPERATURE ZONE J After the key is pressed a menu appropriate for the type of temperature zone is shown For Programmable Energy Saver Modules Upstairs O OFF 1 ON 2 HEAT 4 Upstairs 3 COOL 4 TIME STAT T For temperature sensors Upstairs 2 LOW 3 HIGH STAT To set a temperature setpoint press 2 HEAT or 3 COOL For Celsius temperatures press the key prior to entering the temperature to make the number negative The Celsius temperature may also be specified in 0 5 degree steps if three numeric digits are entered The third digit adds a 5 to the first two digits if it is any thing other than zero Enter a leading zero if necessary In additions to setpoint changes an energy saver may be turned On or Off It may also be turned On or Off for a specific duration Pa
87. ecaaecaeecaeeeseseneeeeeenreeas 32 Freeze ose dees secede 34 Indoor and Outdoor Temperature 34 Temperature Control of ici csacesee set cacdvsesdostussseuddeddadudcutedsacesdestecstccacs duccedasenceasaddvceufesiecsace 35 35 35 36 Configuring HEC Devices a 36 Configuring HLC Devices using an Omni 36 Configuring HLC Devices using an OmmiTouch 37 Setup Mode for 37 FVM ocean et aidan sa venus T Ann et lead 39 40 40 Show te ee ee 40 LOS MESSA E
88. ed to prevent accidental alarms caused by an error while arming If an entry exit zone is Not Ready unsecured when the exit delay expires the Exit Error sequence is initiated as follows gt gt gt gt The sounder s are activated Console Entry Chime comes on The console display indicates DISARM SYSTEM PRESS OFF THEN CODE The system will wait the Entry Delay time If the security system is not turned off during the Entry Delay gt gt gt gt gt The display shows the type of alarm and the violated zone BURGLAR ALARM ZONE NAME TRIPPED The system waits the Dial Out Delay then if configured begins to dial out The central station will be sent a code representing the type of alarm zone violated and an Exit Error code The When Alarm macro is activated any associated programs will be executed The Flash For Alarm Unit Number begins to flash on and off Note The Exit Error feature is incompatible with Auto Bypass If enabled Auto Bypass will override this feature Page 8 Bypassing Zones 8 BYPASS You can Bypass a zone that you do not want protected while the system is armed Bypassing is also the only way that a tamper or panic zone can be disarmed For example if there is a liquor closet or gun case on a tamper zone then you must bypass that zone to gain access to it Another reason to Bypass a zone is if the zone is having trouble If a zone is causing a trouble indicat
89. elay is in effect During the last 10 seconds of the exit delay the audible indication will beep twice as fast to let you know that you must leave at once Press the 0 key to select No this console will not beep during the exit delay or the 1 key to select Yes this console will beep during the exit delay After selecting press the down arrow key to change this option for the next console CONSOLE 1 AUD EXT 1 O NO 1 YES The default setting for Console 1 8 Audible Exit Delay is Yes House Codes 1 4 Format House Codes 1 4 can be configured to use the Standard Preset Dim Command Extended Code Level Command Lightolier s Compose Mode UPB open transmission format Lutron s RadioRA transmission format HAI Lighting HLC and CentraLite transmission format HC 1 FORMAT 5 HAI LIGHTING CHNG 4 To change format for House Code 1 press the key and then use the arrow keys to scroll through the list of formats Press the key to select the desired format After selecting press the down arrow key to change format for the next House Code FORMAT NUMBER DESCRIPTION STANDARD 0 Preset Dim Command X 10 X 10 Pro Leviton PCS etc EXTENDED 1 Extended Code Level Command Leviton COMPOSE 2 Compose Mode Lightolier s Compose UPB 3 Universal Powerline Bus open format RADIO RA 4 Lutron RadioRA HAI LIGHTING 5 HAI Lighting Control HLC CENTRALITE 6 CentraLite Lighting The default setting for HC 1 4 Format is 5
90. ence of an alarm You are first prompted to select the type of alarm SELECT ALARM TYPE ANY TYPE The arrow keys used to select from list of alarm types ANY ALARM BURGLARY ALARM FIRE ALARM GAS ALARM AUXILIARY ALARM FREEZE ALARM WATER ALARM DURESS ALARM TEMPERATURE ALARM Press the key when the desired alarm type is shown You are then prompted to specify the area if area arming is being used AREA ENTER AREA O ALL 4 he area number should be entered followed by key or the arrow keys may be used to scroll through list of areas X 10 Event Buttons Pressing the 6 X 10 key allows you to specify an event button activation upon receipt of an X 10 command from a source external to Omni The Omni can also respond to scene changes initiated at Compose keypads and dimmers When a scene change is initiated Omni can activate an event button program You are first prompted to enter X 10 house code X 10 HOUSE CODE 1 16 A P You are then prompted to enter the X 10 unit code X 10 UNIT CODE 1 16 O ALL Page 62 Finally you are prompted to specify the command that activates event button WHEN X 10 1 O OFF 1 ON 2 SCENE After specifying the X 10 House Code and X 10 Unit Code select 0 for Off 1 for On or 2 for Scene Off events will be activated whenever the selected device is turned off On events will be activated whenever the selected device is turne
91. esenting options appropriate for that type of thermostat is then displayed For heat cool thermostats with auto changeover Upstairs MODE O OFF 1 HEAT 2 COOL Upstairs MODE 3 AUTO t To change a temperature setting press 2 HEAT 3 COOL or 2 TEMP as appropriate Upstairs HEAT ENTER TEMPERATURE Upstairs COOL ENTER TEMPERATURE Upstairs TEMP ENTER TEMPERATURE Enter the desired temperature then press key The fan control on a thermostat may be switched between on and auto by selecting 4 FAN from the temperature menu Page 31 Upstairs FAN O AUTO 1 ON Thermostats may be switched between hold mode and the normal run mode While in hold mode the thermostat does not respond to scheduled temperature changes but instead maintains the temperature at its current setting The thermostat will then return to its scheduled operation setting once hold mode is removed The hold menu is used to control hold status of a thermostat The hold menu is entered by selecting 5 HOLD at the temperature menu Through this menu you may turn hold mode on and off For a heat cool thermostat the menu displayed is Upstairs HOLD O OFF 1 ON Turn hold mode Off On by selecting 0 OFF or 1 ON respectively For a heat cool thermostat the status shows the current temperature the heating and cooling temperature setpoints whether hold mode is on the system mode and the fan On Auto selection Upstairs TEMP 78 HE
92. esting Systemics eM tae meme dle anata dll Ble ea thts 16 Control Commands ose eee ea os EG BR tn ek RR oe RG WB is EE gE a oar a 17 A DOUG UP Be ooh cee BeBe So ATR cecal SOE ie SR oat OREO ae SSSR Lis de Rie ORE 17 HAL Lighting Control Ronmat nee aah Ree ees Reh ed a 18 ABOUt ROOMS 18 About ROOM Controllers E E N 18 Roon Controller LED Indicators o 18 About Hous Controllers esse cto thaws duced Os 19 BEN 00 01 1 eS Oe 19 About 19 RP 20 o 20 00 61 Goal 20 20 UI NUMBERS E 21 Scrolling Through Names ror R E E 21 ia gs Sx ace pe eae
93. f To issue Phantom Button commands from the top level display or from the main menu press the 4 ALL key on the console keypad and then press the 4 PHANTOM key You are prompted to enter a Phantom Button 1 17 ENTER BUTTON 1 17 Enter Phantom Button number 1 17 followed the key PHANTOM BUTTON 1 O OFF 1 ON When a Phantom Button is turned on all of the devices that are pre programmed with that Phantom Button will go to their preset light levels When a Phantom Button is turned off all of the devices that are pre programmed with that Phantom button will turn off Executing CentraLite Scenes Omni can turn on and turn off each of the 255 possible CentraLite Scenes To issue CentraLite Scenes commands from the top level display or from the main menu press the 4 ALL key on the console keypad and then press the 5 CENLIT key You are prompted to enter a Scene 1 255 ENTER SCENE 1 255 Page 29 Enter CentraLite Scene number 1 255 followed be the key CENLIT SCENE 1 O OFF 1 ON When a CentraLite Scene is turned on all of the devices that are pre programmed for that scene will go to their preset light levels When a CentraLite Scene is turned off all of the devices that are pre programmed for that scene will turn off Buttons A powerful feature of the Omni is the ability to program Buttons A Button also known as macro is a number on the keypad that is programmed to execute
94. fined lighting levels To set the lights in the selected group to a predefined scene enter the Scene number 2 13 which corresponds to Scene A L respectively followed by the key lights that are part of the selected group are set to the predefined lighting levels for the selected Scene Timed Commands The timed commands allow a units to be turned on or off for a specified period of time The unit may be turned On for 1 99 minutes or seconds or 1 18 hours then Off or turned Off for 1 99 minutes or seconds or 1 18 hours then On Lighting units 1 64 may also be dimmed or brightened for a specified period of time The unit may be dimmed 1 9 steps for 1 99 minutes or seconds or 1 18 hours then brightened back to its previous level or brightened 1 9 steps for 1 99 minutes or seconds or 1 18 hours then dimmed back to its previous level To enter a timed command you must first enter the unit that you want to control From the control menu enter the unit number or scroll to it using the arrow keys then press the key To enter a time press the 9 TIM key Before any digits are entered the key may be used to switch between minutes seconds and hours After you choose enter a time 1 99 for seconds amp minutes and 1 18 for hours Once the time is entered the control menu is redisplayed with the specified times shown For example Entry Lights For 2H O OFF 1 0 2 DIM 3 BRTV Status of
95. ge 33 To turn energy saver Off select 0 OFF To turn the energy saver On select 1 ON turn energy saver or Off for a specific duration select 9 TIME prior to selecting On or Off Enter the time as described under Control Unit Commands Downstairs 1 ON 2 HEAT 4 Downstairs 3 COOL 9 TIME STAT T ENTER TIME MINUTES 1 99 H M S Downstairs FOR 15M O OFF 1 ON The current status of a temperature zone may be displayed by selecting STAT key from the main temperature menu The status display differs depending on the temperature zone type When you are finished press the key twice to return to the top level display IMPORTANT NOTES gt There is 3 minute minimum on and off time for PESMs designed to prevent short cycling your HVAC compressor If the PESM has just turned the HVAC system on or off it will wait 3 minutes before changing it even though the display does change gt Ifyou change the Heat or Cool setback temperature on the PESM the system will insure that there is always at least four degrees Fahrenheit difference between the Heat and Cool temperatures by altering the other setback temperature as necessary gt 5 are NOT affected by All On or All Off commands Freeze Alarms Thermostats and PESMs can also be used to report potential freeze conditions before damage to pipes and appliances can occur An alarm is activated when any Thermostat or PESM detects a
96. gram the system to turn on the bathroom heat if the outdoor temp goes below 45 degrees High and Low temperatures are changed the same way as a PESM Page 34 When a temperature sensor is selected from list of temperature devices you may set a Low and High setpoint for activating programs or alarms Enter the desired temperature then press the key Upstairs 2 LOW 3 HIGH STAT For negative temperatures 1 to 40 press the key prior to entering the temperature to make the number negative A Celsius temperature may also be specified in 0 5 degree steps if three numeric digits are entered The third digit adds a 5 to the first two digits if it is any thing other than zero Enter a leading zero if necessary Temperature Control of Appliances You can control appliances such as a ceiling fan using Advanced Control Programming ACP of the Omni For example the ceiling fan can be programmed to come on if the temperature goes above the High temperature High and Low setpoints for temperature zones are changed the same way as the PESM However on off control of the ceiling fan 15 done from the 1 CONTROL menu Use the ceiling fan s unit number to turn it On or Off The PESM or Model 31A00 Temperature Sensor and the ceiling fan are linked together by an event button program Temperature Alarms Temperature sensors can be used to signal that a temperature in a special room like a greenhouse or wine cooler
97. groups devices by House Code which consists of 16 consecutive unit numbers starting at Unit 1 Each House Code can be configured to a different lighting protocol format such as Standard X 10 Extended X 10 Lightolier Compose UPB open UPB format where you can use the programming capability in the Omni controller to communicate with the UPB network Lutron RadioRA CentraLite or HAI Lighting Control HLC Different lighting devices can not share the same House Code However different lighting devices can coexist on an Omni system as long as they are on separate House Codes For example House Code 1 Units 1 16 HLC House Code 2 Units 17 32 UPB House Code 3 Units 33 48 X 10 Extended House Code 4 Units 49 64 CentraLite Page 20 Unit Numbers Omni IIe systems have 128 total Unit Numbers They consist of HLC UPB CentraLite RadioRA ALC Compose and X 10 module unit numbers hardwire voltage output unit numbers and internal flag unit numbers as follows Omni Unit Numbers Module Output Unit Numbers 1 16 HLC Room 1 and 2 UPB Unit ID 1 16 CentraLite loads 1 16 RadioRA Lighting Zones and Master Controls 1 16 or X 10 modules 1 16 House Code X 17 32 HLC Room 3 and 4 UPB Unit ID 17 32 CentraLite loads 17 32 RadioRA Lighting Zones and Master Controls 17 32 or X 10 modules 1 16 House Code X 1 1 31 ALC addresses 1 31 Branch 1 33 48 H
98. h Tone service then Dial Type must be set to Pulse The default Dial Type is Tone My Phone Number My Phone Number 15 the phone number that will be announced when the Omni dials out in the event of an alarm It should be set to the phone number of the premises where your system is installed To enter phone numbers press the keypad keys 0 9 You can put in a dash for legibility by pressing the Off key Press the key after you have pressed all of the digits in the phone number For example to enter the number 555 1234 press 555 OFF 1234 Dial Out Number 1 Dial Out Number 1 is one of the 8 numbers that are stored in the system In the event of an alarm these numbers are dialed in the order that is set up in the Dial Out Order for the particular type of alarm Dial out numbers 1 8 have On and Off times and days so that no time is wasted calling you at the office at night or on a Sunday if the alarm is activated For dial out number 1 you should enter your office number where you can be reached during working hours Enter the phone number the same way as described for My Phone Number You can cause the system to pause for two seconds between digits of the number by pressing the DAY key which puts a T in the number Multiple Ts for longer pauses are allowed You can also press the NIGHT key and the AWAY key for symbols to get through some types of telephone or pocket beeper pager systems To prevent a call wa
99. h with Link 50 will go to 0 to achieve the All Off effect Setting a Link Lighting Scenes Lighting scenes are created by pre configuring light levels and fade rates in one or more UPB devices that get activated and deactivated by a Link command or button press on a 6 Button or 8 Button Keypad Each UPB Wall Switch can hold up to sixteen different preset light levels 0 100 that can be linked to the Omni Ile controller or to a pushbutton on a 6 Button or 8 Button Keypad Omni can set each of the 250 possible Links The Link command is used to set up lighting scenes for a lighting group To set a lighting scene using Omni adjust all of the UPB Wall Switches with the pre configured Link to the desired lighting levels The desired lighting levels may be set manually at the switch or by a command issued from Omni After the desired lighting levels are set the Link Set command be transmitted by Omni to save the new light levels for each of the devices pre configured with the specified Link Executing Phantom Buttons Omni can turn on and turn off each of the 17 possible Phantom Buttons Phantom Buttons must be pre programmed into the RS 232 interface or Chronos Phantom Button 16 is always assigned to All On if the Phantom button is turned on or off and Phantom Button 17 is always assigned to if the Phantom button is turned on or of
100. has gotten too high or too low If the temperature in this zone goes above the High setpoint or below the Low setpoint the console beeper is activated inside and outside sirens are not activated and the central station and or voice dialer is called The High and Low setpoints are changed as described for the PESM Use the zone number that the temperature sensor is connected to in place of the unit number NOTE Setting a High or Low temperature to 0 takes it out of service Humidity The Model 31A00 2 and 31A00 8 Indoor Outdoor Temperature and Humidity Sensor is used for sensing indoors temperature and or reporting the relative humidity from 0 to 100 percent or for sensing the outdoor temperature and or reporting the outdoor relative humidity High and low humidity limits can be set for taking action i e turning on the bathroom vent fan running a c in de humidification mode turning on humidifier in heating mode etc or reporting high or low humidity conditions in homes greenhouses wine cellars coolers humidors etc Controlling humidity is particularly helpful in combating the growth of mold in vulnerable areas of the home such as bathrooms basements attics etc The humidity level 0 100 the low humidity setting and high humidity setting can be viewed and modified using the temperature menu To enter the temperature menu from the top level display or from the main menu press the 5 TEMP key The humidity zone can be specified b
101. he next number in the Dial Order The dialer will wait up to 45 seconds after it finishes dialing for a voice to answer the call If it doesn t hear a voice in that time it goes on to the next number The voice dialer will respond to answering machines After it has dialed the last number in the dial order the Omni stops dialing and reconnects the in house phones Page 48 What the Omni Voice Dialer Does When an alarm is activated the Omni will wait the Dial Out Delay If your system is monitored by a central station it will be notified first Then the voice dialer will dial out to the numbers as described above If the alarm is turned off at the console while a voice dial out is in progress the dial out will be canceled immediately and the voice dialer will hang up If the number dialed is busy or if all lines are busy the dialer will immediately hang up and go to the next number in the Dial Order The dialer will wait up to 45 seconds after it finishes dialing a complete phone number for a voice to answer If it doesn t hear a voice in that time it goes on to the next number The voice dialer will respond to answering machines After it has dialed the last number in the dial order the Omni stops dialing and reconnects the in house phones What You Hear If Your Omni Calls You When you pick up the phone and say something the Omni will say one of the following depending on type of alarm BURGLAR ALARM
102. he console or a more serious problem Call your installer for service Codes There are 16 user codes that you may assign to users of the system Omni codes are 4 digits in length A code can be any number from 0001 to 9999 Each user should be assigned a security code with an authority level areas that can be accessed if area arming is used and times and days in which the code will be valid Memorize your codes Don t give them to anyone who doesn t need to know them The levels of authority that you can assign to a user code are Master Manager and User Master Code The Master code allows complete access to the entire system Only the owner s or the one s who will govern the system should have and use the Master code A Master code is allowed access to all areas all the time User code 1 is always set to a Master code See Set Up Codes Page 13 Manager Code The Manager codes can arm disarm the security system in assigned areas during assigned times The Manager code can access functions that are code protected in High Security mode Managers may also access the system from an outside telephone line User Code User codes can only be used to arm and disarm the security system in assigned areas when the time assigned to that code is valid Duress Code If you are forced to disarm the system against your will by an intruder disarm it as you normally would but use the Duress Code instead of your normal code The system
103. hough the actual readings are taken 10 times per second To enter the Test menu from the Status menu press the 4 TEST key on the console keypad The first display shows the current battery reading and the phone line status A battery test is initiated when the status mode is first entered The new battery reading is updated ten seconds later The low battery limit is also displayed The phone status consists of two parts separated by The first part shows the current phone line state ONHK ON HOOK OFFHK OFF HOOK RING RINGING DEAD DEAD PHONE LINE The second part shows how the Omni is currently using the phone line IDLE NOT USING THE PHONE LINE LOCAL LOCAL ACCESS REMOTE REMOTE ACCESS VOICE IN VOICE DIAL OUT MODE EMGACC ACCESS AFTER VOICE DIAL OUT DCM IN DIGITAL COMMUNICATOR MODE BATTERY 230 LIMIT 200 PHONE ONHK IDLE Next display shows the A D reading for battery voltage phone line voltage AC power on bell and fuse BAT 225 PHONE 140 ACON 82 BELL 215 FUSE 222 Page 38 The next series of displays shows current analog reading for each security zone input The displays show readings for zones 1 48 1 147 2 148 3 147 4 146 5 146 6 147 THROUGH 43 148 44 147 45 147 46 145 47 149 48 146 1 Normal readings for zones are between 137 157 when secure If Zones 1 4 are configured as Fire or Gas zone normal readings are between 26 43 when secure Each
104. hts and appliances by sending commands over the ALC signal wiring to ALC Switch Modules ALC Switches communicate with the Omni over low voltage signal wire They are two way devices so the controller always knows the actual status of the switch In addition ALC switches can be used to set scenes by triggering macros in Omni IIe When ALC Lighting Control Modules are being used it is also possible to ramp the lighting level of an ALC Dimmer Switch to a new level at a controllable ramp rate ALC Module Types The ALC modules types are Dimmer Switch Relay Switch Slave Switch Program Switch and 4 Button Scene Switch Modules About X 10 The Omni controls lights and appliances by sending commands over your existing electrical wiring to special switches outlets receptacles and modules collectively referred to as X 10 Each module or group of modules is assigned a House Code and a Unit Number so that the Omni can control the modules individually When a module hears a command from the Omni for its house code and unit number it executes the command There are 3 different X 10 formats Standard X 10 Preset Dim Extended X 10 Extended Level and Compose Any module that is X 10 Compatible will work with the Omni The modules come in various types House Codes Omni can control up to 64 lighting and appliance devices Each device switches modules and keypad has its own Unit Number 1 64 Omni
105. ide Area Network Page 52 SETUP Configuration and Advanced Control Programming ACP The Setup menu is used to configure operating parameters program your system to do its automated control and security functions using ACP and give text and voice descriptions to all of your zones units buttons codes temperatures and messages To enter the Setup menu from the top level display or from the main menu press the 8 SETUP key on the console keypad Upon entry to the Setup mode you will first be prompted to enter a security code SET UP ENTER CODE A Master code is required to enter the Setup mode SET UP 1 CODES 2 TIME 3 PROG 4 DIAL 5 ARM 6 MISC 7 NAMES 8 VOICE Set Up Codes Omni has 16 user codes that you may assign to users of the system Omni security codes are 4 digits in length 0001 to 9999 and must be unique The controller will not allow the duplication of any user code including the Duress Code You may however enter 0000 to disable a code User Code 1 is always set to a Master code All other user should be assigned a security code with an authority level areas that can be accessed if area arming is being used and times in which the code is valid To set up a code from the Setup menu press the 1 CODES key Use the arrow keys to scroll through the codes CODE 2 0000 9999 0000 DISABLE The existing code number is not shown on the display To change the code enter a four digit n
106. ide you with step by step configuration status Once completed press the Exit icon Setup Mode for HLC Devices To configure HAI UPB Wall Switches and Dimmers put the device in Setup mode as follows Step Operation 1 rocker switch quickly 5 times The HAI UPB Wall Switch or Dimmer will flash the lighting load one time and blink its LED blue to indicate that it is in Setup Mode Note The switch will automatically exit Setup mode after 5 minutes To manually exit Setup mode tap the switch quickly 2 times To configure the HAI UPB 6 Button Room Controller put the device in Setup mode as follows Step Operation 1 Press and hold the ON and OFF pushbuttons simultaneously for at least 3 seconds 2 All of the LED indicators will blink to indicate that the HAI UPB 6 Button Room Controller is in Setup Mode Note The HAI 6 Button Room Controller will automatically exit Setup mode after 5 minutes To manually exit Setup mode press and hold the ON and OFF pushbuttons simultaneously for at least 3 seconds To configure the HAI UPB 8 Button House Controller put the device in Setup mode as follows Step Operation 1 Press and hold the 1 and 8 pushbuttons simultaneously for at least 3 seconds 2 All of the LED indicators will blink to indicate that the HAI UPB 8 Button House Controller is in Setup Mode Note The HAI 8 Button House Cont
107. ies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements The Industry Canada does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution Users should not attempt to make such connections themselves but should contact the appropriate electric ins
108. igure HLC devices from an Omni console use the Status menu To enter the Status menu from the top level display or the main menu press the 6 STATUS key on the console keypad STATUS 1 CTRL 2 ZONE 3 SUN JV Page 36 Press 1 CTRL to view current status of each unit and to configure the HLC device that is assigned each unit The console will display Porch Light STATUS OFF You may enter unit number to display selected unit or simply press down arrow key to scroll through the list of named units When the desired unit is displayed put the selected HLC device into Setup Mode See Setup Mode for HLC Devices and then press the key twice i e The display will provide you with step by step configuration status When complete the display shows CONFIGURE Porch Light COMPLETED Once completed press the key to return to the Status display and select your next unit device Put the next selected HLC device into Setup Mode See Setup Mode for HLC Devices and then press the key twice to configure the selected device Configuring HLC Devices using an OmniTouch Touchscreen To configure HLC devices from an OmniTouch touchscreen press the Control icon on the Home page Select the desired unit from the Control list box to display the unit dialog Put the selected HLC device into Setup Mode See Setup Mode for HLC Devices and then press the Config button The display will prov
109. ill make Dial Out Number 1 never active Dial Out Numbers 2 8 The default Dial Out On and Off times are the same as Dial Out Number 1 Dial Order The dial order is the order in which call all will be placed if an Alarm is activated You can have the system make up to 8 calls in the event of an alarm You may chose from Dial Out Numbers 1 8 You can have the system dial a number twice or more which is suggested if you don t have a direct dial number at work so that your company operator can find you if you aren t at your desk and have you alerted for the next call Up to eight numbers may be entered Enter the Dial Out Order by pressing the keypad digits 1 2 3 4 5 6 7 or 8 for Dial Out Numbers 1 2 3 4 5 7 8 respectively When you have entered dial order of your choice press Enter a single 0 if no dial out is desired The default Dial Orderis1234567 8 Set Up Arming To configure different arming and disarming options from the Setup menu press the 5 ARM key Entry Delay The Entry Delay is the time in seconds that you have to disarm the alarm system after entering your home The Entry Delay only applies to the entry exit zone e g your entry doors If you or someone else come in through a window there will be no entry delay and the alarm will sound immediately When you come in through a door on an entry exit zone the other zones are delayed too This allows you to get to your phone or c
110. ime should be 13 00 23 59 TIME 8 00 AM HHMM tT RISE AM J SET PM Select 2 DATE DAY to enter a new date or days of week DATE 10 15 MMDD 4 DAY Next specify if the program will run once on the specified date and then be deleted or if the program will run every year on the specified date yearly RUN PROGRAM 1 ONCE 2 YEARLY To change days press the down arrow DAY key You will be prompted to enter the day s that the program will be activated Press 1 7 for Monday Sunday 0 for Once 8 for Weekdays and 9 for Weekends then DAY S M W F 1 7 MON SUN 0O ONCE Press the key and the display will then return to the Edit Program menu EDIT PROGRAM 1 WHEN 2 CMD 3 amp COND Page 58 Button and Event Programs Selecting 2 BUTTON from the Edit When menu sets up a program to be activated when a macro button is executed or an event occurs The user is prompted to specify the button event that activates the program BUTTON ENTER BUTTON MENU 4 A specific macro button may be activated by entering the button number followed by the key or by using the arrow keys to scroll through a list of buttons To program specific event buttons i e Front Door Opens Security Armed Away Porch Light Turns On etc press the key to bring up a menu of event button types BUTTON TYPE 1 CTRL 2 SEC 3 ZONE 4 4 ALL 5 ALARM 6 X 10 7 MISC 8 MSG 9 SWITCH 7 After the event button is specified the display
111. inal Page 5 SECURITY SYSTEM OPERATION Disarming the Security System and Silencing Alarms Before going any further you should know how to disarm your security system in the event that the alarm sounds Turning the system OFF disarms the burglar alarm resets emergency alarms and silences all sirens and sounders Press the OFF key OFF Watch the display The top line will read DISARM The bottom line will read ENTER CODE indicating that you must enter your code number to disarm the system For each digit that you press will appear indicating that the key has been pressed Now enter your four digit code 41 0 That s all there is to it After the four digit code has been successfully entered the console will beep once to indicate that you have correctly disarmed the system The console LED will be set to green and the display will return to the normal top level system display If an incorrect code is entered the console will beep three times and display INVALID CODE Re enter your code In the event that you make a mistake press the OFF key again and then enter your four digit again Practice disarming your system until you are comfortable with this procedure NOTES gt Panic Tamper and Fire zones are always armed as are the Emergency buttons on the console gt In the event that the alarm has been activated the menu keys and the arrow keys are locked out You must silence the al
112. iness and would like to protect an inventory stockroom separately from the offices in your building The console in each area acts as if it were controlling its own Omni system Each area is assigned by your installer a group of zones control units macro buttons messages and thermostats These items can only be controlled where they have been assigned Omni Maintenance Your Omni controller and the consoles are designed to require very little maintenance For smoke detectors motion detectors and other components not manufactured by HAI and follow maintenance procedures outlined by the manufacturer Consoles can be cleaned using a mild detergent and a soft cloth Every three years or if the BATTERY LOW TROUBLE NOW indication comes on and stays on for an extended period without reason the rechargeable battery in the controller should be replaced The recommended battery type is a 12 volt 7 amp hour sealed lead acid battery To replace the battery disconnect the red battery wire from the battery terminal Cover the connector at the end of the wire with electrical tape to avoid its touching anything in the enclosure Disconnect the black wire from the battery terminal and cover the connector at the end of the black wire with tape Remove the old battery Install the new battery by reversing the removal procedure Be very careful to connect the Black wire to the terminal on the battery Red wire to the term
113. ing in the event of a fire It is your responsibility to plan your escape routes in the event of a fire alarm Your family should practice fire drills periodically to ensure that everyone is familiar with the plan 1 Draw a floor plan of your home showing location of fire and smoke detectors Show two exit routes from each room The primary exit and an alternate escape route 2 Be sure that your family knows what the fire alarm signal sounds like 3 Inthe event of a fire alarm DO NOT open a closed door First touch the door If it is hot to the touch use the alternative escape route 4 Since smoke tends to rise keep low to the floor during your escape crawling if necessary If you encounter any smoke hold your breath 5 During a fire alarm do not stop to pack or gather belongings Exit immediately and meet at a designated spot outside the house 6 DO return to burning house 7 Notify the fire department using a neighbor s telephone 8 Review your escape plan and rehearse a fire alarm periodically with your family Page 81 FEDERAL COMMUNICATION COMMISSION NOTICE 1 This equipment complies with Part 68 of FCC Rules On the door inside of the Omni enclosure is a label that contains among other information the FCC registration number and Ringer Equivalence Number REN for this equipment If requested provide this information to your telephone company 2 FCC compliant telephone cord and modular
114. ion you can bypass that zone to cut it out of the system until repairs are made When a zone is bypassed it is no longer checked for alarms When you bypass a zone using the console or over the phone it will Stay bypassed until you Restore it The console status display will show that the zone is bypassed only when the security system is disarmed When the system is armed it does not display bypassed zones To bypass a zone from the main menu or from the top level display press 2 on the console keypad then 8 for bypass Enter the zone number followed by the key or use the arrow keys to select the zone After the zone is entered you will be prompted to enter your security code The bottom line will now read ZONE NAME BYPASSED to remind you that the zone is bypassed If a fire zone is bypassed the console will continue to beep until that zone is restored See Restoring Zones Auto Bypass In order to prevent the alarm from sounding unexpectedly if a window or door is open when the system is armed the Omni will automatically bypass the zone if it is opened when the system is armed Note that there is an exit delay before the system is armed in any mode The bypass will only take place if the zone is not ready i e open when the exit delay is over and the system is actually armed When a zone is Auto Bypassed it will be automatically restored once it is secure i e closed or the next time you arm or disarm the system Th
115. is allows you to have up to 8 House Controllers throughout the house that control rooms 1 8 Within the HLC structure House Controllers can also be configured as a general purpose 8 button keypad controller that is used to trigger 8 different macro programs in the Omni When configuring a House Controller as a general purpose 8 button keypad controller it must be set to a unit number between the first and last unit number in a room 1 2 7 10 15 18 23 26 31 34 39 etc When configured as a general purpose 8 button keypad controller programs must be created in the Omni controller for the LED indicator behind each button to function About CentraLite CentraLite is a centralized lighting control system that uses hardwired lighting control technology to control lighting loads fans and mechanical low voltage relays CentraLite lighting scenes are used to control groups of lights which are preset to turn on to various levels of dimming When set to CentraLite the Omni controller can gt Send commands off and level to individual loads and relays gt Receive status on and off from individual loads and relays gt Execute scene commands on and off to control of up to 255 CentraLite lighting scenes gt Receive commands when buttons are pressed on a CentraLite keypad up to 127 About Lutron RadioRA Lutron RadioRA uses wireless communication technology to control lighting Each Switch or Dimmer controls one
116. iting line from interfering with the dial out you may use the call waiting cancel sequence at the beginning of the number The call waiting sequence is typically 7 0 T T pause however this may vary depending on your region If you wish to remove a phone number for a particular dial out number press OFF with the display showing a Dial Out Number to enter a single dash Phone numbers can be up to 24 digits DIAL OUT 1 ON DIAL OUT 1 OFF Page 70 Dial Number 1 has two times associated with it an On and Off time The Omni will only call this number if the time and days are between the Dial Out 1 On and Dial Out 1 Off times and dates Press to change the On and Off times See Set Up Codes DIAL OUT 1 ON 12 00 MTWTFSS CHNG DIAL OUT 1 OFF NEVER CHNG For example if your normal work hours are 8 to 5 Monday through Friday then set Dial Out 1 On to 8 00 AM MTWTF and Dial Out 1 OFF to 5 00 MTWTF With these settings the system will call Dial Out Number 1 only if the alarm is activated on weekdays between the hours of 8 00 AM to 5 00 PM The default for Dial Out 1 is 12 00 MTWTESS and the default for Dial Out 1 Off is Never so that Dial Out Number 1 15 always active The Time that was entered before setting an On or Off time to Never is saved and will be redisplayed when a day is set in place of Never Setting both the Dial Out 1 On and the Dial Out 1 OFF times to Never w
117. lected unit off Press 1 ON to turn the selected unit on 2 DIM does not affect CentraLite units 3 BRT does not affect CentraLite units Press 4 LVL to set the desired lighting level of the selected unit 0 100 5 RMP does not affect CentraLite units VV VV VV WV Press 9 TIM to time the selected unit On or Off Timed commands may be from 1 99 seconds 1 99 minutes or 1 18 hours gt Press STA to see the status On or Off of a CentraLite device Controlling RadioRA Units Entry Lights O OFF 1 ON 2 DIM 3 BRT 4 Entry Lights 4 LVL 5 RMP 9 TIM STAT Press 0 OFF to turn the selected unit off Press 1 ON to turn the selected unit on 2 DIM does not affect RadioRA units 3 BRT does not affect RadioRA units Press 4 LVL to set the desired lighting level of the selected unit 0 100 5 RMP does not affect RadioRA units VV VV VV WV Press 9 TIM to time the selected unit On or Off Timed commands may be from 1 99 seconds 1 99 minutes or 1 18 hours gt Press STA to see the status On or Off of a RadioRA device Note When a RadioRA device transmits a signal i e Switch or Dimmer is turned on or off locally Mater Control button is pressed or Phantom Button is executed Omni will automatically update the status of each affected device Controlling ALC or X 10 Units Entry Lights O OFF 1 ON 2 DIM 3 BRT Entry Lights 4 LVL 5 RMP 9 TIM STAT Pag
118. ll of the HLC devices in the room to the desired lighting levels The desired lighting levels 0 100 may set manually at the switch or by issuing commands from the Omni controller After the desired lighting levels are set use the 6 SET command to save the new light levels for each device in the selected room Living Room SET 1 ON 2 5 When the scene command is transmitted either using a Room Controller or by the Omni controller each HLC device in the specified room will brighten or fade to its preset level for the selected scene Each lighting scene can also be set or easily changed using the pushbuttons on the HAI UPB 6 Button Room Controller as follows Step Operation 1 Press the desired pushbutton on the HAI UPB 6 Button Room Controller to activate the current scene preset lighting level in each of the HLC devices 2 Use the local Decora style rocker switch on each UPB Wall Switch Dimmer s to set the desired lighting level s issue commands from the Omni controller 3 Press the pushbutton on the HAI UPB 6 Button Room Controller five 5 times quickly 4 Each UPB Wall Switch Dimmer will flash its lighting load one time to indicate that the new level has been configured Controlling Individual Lighting Loads in an HLC Room or UPB Units To control individual lighting loads in a room use the down arrow key to scroll through the list of units When the
119. m If the specific item number is known enter the item number followed be key or scroll up and down among the named items After the unit has been selected press the key The console will display Controlling a Room of HLC Lighting Living Room O OFF 1 ON 2 5 A D Living Room 6 SET STAT Press 0 OFF to turn the selected room off all lighting loads in the room are turned off Press 1 ON to turn the selected room on all lighting loads in the room are turned on Press 2 A to set all of the lighting loads in the selected room to their preset levels for Scene A Press 3 B to set all of the lighting loads in the selected room to their preset levels for Scene B Press 4 C to set all of the lighting loads in the selected room to their preset levels for Scene C Press 5 D to set all of the lighting loads in the selected room to their preset levels for Scene D Press 6 SET to set up a lighting scene for the all of the lighting loads in the selected room On A D VV VV VV V WV Press STA to view the current status of the room Page 21 Configuring Lighting Scenes in HLC Room Lighting scenes are created by configuring light levels for HLC lighting devices in a room Each HLC device in a room can store up to four different preset lighting scenes Scenes A D and one On Scene preset lighting levels for each device when the room is turned on To set a lighting scene using the Omni console adjust a
120. man operator who notifies the appropriate authorities Digital communications to a central station are generally superior to voice communications because the central station is always staffed with trained professionals and there is virtually no chance for misinterpretation The digital communicator will not dial out until the Dial Out Delay has expired By default there is a communicator delay of 30 seconds The delay can be removed or increased up to 45 seconds Please consult your installer about the Dial Out Delay When enabled if the alarm is canceled prior to the expiration of the Dial Out Delay no transmission will take place If the alarm is canceled after the Dial Out Delay has expired all alarm trips will be transmitted followed by a Cancel code The communicator may be set up to automatically send a test code to the central station on a daily or weekly basis This verifies proper operation of the entire monitoring system on a periodic basis When the digital communicator is used all voice dial outs will be delayed for five minutes after the expiration of the Dial Out Delay to allow time for the central station to call the premises If the HAI Two Way Audio Module is being used after the transmission of the alarm to the central station the operator can talk and listen to people and sounds at the premises If the digital communicator is unable to successfully communicate with the central station the console will display a Communicat
121. menu is modified to allow Scene commands Consequentially the Level and Ramp Commands are removed from the menu Entry Lights Unit Name 4 SCN 9 TIM STAT Page 64 If the selected unit is not capable of dim and bright commands only a single menu is shown Porch Light Unit Name O OFF 1 ON 9 TIM STA If the selected unit is UPB press 6 LED to control an LED on a UPB Keypad On the 6 Button Keypad LED 1 is behind On button LED 2 is behind the Off button and LED 3 6 is behind the A D buttons respectively On the 8 button Keypad LED 1 8 is behind the 1 8 buttons respectively For example WHEN U1 SW 3 UNIT 1 LED 3 ON This program illuminates the A button on a 6 Button Keypad when the A button on that keypad controller is pressed This program can also be used to illuminate the 3 button on an 8 Button Keypad when the 3 button is pressed If the selected unit is UPB the STA key is used to request the status form the specified UPB device WHEN LINK 1 ON Porch Light STATUS When Link 1 is received on the UPB network Omni sends a status request message to the UPB Wall Switch named Porch Light to acquire its current status This Status Request program is particularly beneficial to keep the current state of UPB devices that are altered by a lighting scene Link On or Link Off command When the Link On or Link Off command is transmitted by a
122. n activate the Police Emergency keys by picking up the phone and pressing the key 6 times This activates the sounder immediately The first that you press logs you in as usual then the next 5 presses of the key activate the alarm If you are already logged into your system then it takes only 5 presses of the key to activate the emergency alarm To prevent accidental activation of the panic feature over the phone you must press the key 5 times all at once If you pause for more than 2 seconds or press any other key the panic activation is canceled The Omni will say CANCEL Note that the Panic Button over the Phone feature only works if you are logged into the system In an emergency if you wish to set off the alarm simply pick up the phone and repeatedly press the key until the alarm sounds Be aware that under some circumstances it may be smarter to dial 911 or your police department directly Also be aware that your telephone will be unusable while the Omni dials out Page 47 Emergency Dial Out Emergency dial out consists of two distinct parts the digital dialer and the voice dialer Digital Dialer The digital dialer also called a digital communicator reports alarm events to a central station monitoring center The digital dialer sends a digitally coded message to the central station s receiver and computer The computer in the central station presents your name address and other information to a hu
123. n the console to arm the system in the Day Night and Away security modes and Off to disarm without having to go into the security menu From the top level display press one of the shortcut security keys Enter your code number on the console keypad The console will beep once and the console LED will be set to red The top line will display the security mode to indicate that you have correctly armed the system The system will be fully armed after the Exit Delay expires The programmed Entry Delay is seconds The programmed Exit Delay is seconds Quick Arm For extra convenience the Omni can be armed by simply pressing the DAY NIGHT or AWAY button twice eliminating the need to enter the code To quick arm the system in the Away mode from the top level display press AWAY AWAY The quick arm feature only works if the alarm system is in the Off mode and if no alarms are sounding This feature is disabled when the system is shipped If desired it can be enabled or disabled at any time See Set Up Arming Enable Quick Arm Page 7 What Happens When You Arm Security System To arm the system into one of the 6 security modes from the security menu choose the security mode and press the appropriate key 1 gt gt gt gt 6 and then enter your user code number on the console keypad or use one of the Shortcut Keys as described The console will beep once and the console LED will be set to red The con
124. nes A D Room Controller LED Indicators When the room 15 turned on the LED indicator behind button is illuminated and all others are turned off When the room is turned off the LED indicator behind the button is illuminated and all others are turned off When the room 15 brightened the LED indicator behind the On is illuminated and all others are turned off When the room is dimmed the LED indicator that is currently illuminated stays on When the room is set to a lighting scene A D the LED indicator behind the respective scene letter is illuminated and all others are turned off When Status Tracking is enabled this is the default setting Omni keeps track of the exact status of each unit even when a lighting scene is initiated by the Room Controller Room Controllers also keep track of when individual switches in a room are turned on and off When all of the lighting loads in a room are turned off the Off indicator is illuminated If any of the lighting loads in a room are turned on at an HAJ UPB Wall Switch or Dimmer the indicator will illuminate and the Off Page 18 indicator is turned off Likewise if the indicator or one of scene indicators is illuminated and then all of lighting loads are turned off at HAI UPB Wall Switches and or Dimmers the indicator will illuminate and any others are turned off About House Controllers The
125. ng th Security SyStenn asst 6 Using SHOTECUEKCY Sis leon E Basset 7 a oe 7 What Happens When You Arm the Security 8 Exit Erron OGRE NE 8 By passin sai oxy hilar ae satan Sails 9 9 Restoring 9 What Do When You 10 What Happens When Alarm is 10 BurglarAlarm Activated aca huddle kannada RAR 10 HarevAlarin A Ctr SSS E oo ee eS SOE Soe 11 G s Alim Activated ose Os BUS See Sa Ta Bo 11 U0 9 op 884236 ON a KEYS a PC Po re ee
126. nits 17 24 etc Each room can consist of a maximum of 8 HLC devices configured as follows Up to 7 HAI UPB Wall Switches Dimmers and or Modules for controlling up to 7 lighting loads in a room or area 1 or more Room Controllers set a scene in a room turn the room on and off and dim and brighten the room 1 House Controller for controlling up to 8 rooms of HLC lighting 1 or more House Controllers used as a general purpose 8 button keypad controllers VVVV The first unit number in each room i e 1 9 17 25 etc is reserved for controlling the room The name for this unit should reflect the room name e g Kitchen Great Room Theater etc HLC Wall Switches Dimmers or Modules cannot be programmed to these unit numbers If one or more Room Controllers are used the first Room Controller should be set to the first unit number in the group i e Unit 1 additional Room Controllers can be used by setting each to any other unused unit number in the group i e Units 2 8 About Room Controllers The HAI UPB 6 Button Room Controller allows for lighting control of a room where HAI UPB Wall Switches Dimmers and Modules have been installed From a Room Controller the room can be turned off all loads in the group are turned off turned on all loads in the group are turned on brightened all loads are brightened from their current level dimmed all loads are dimmed from their current level or set to one of 4 lighting sce
127. odes temperatures areas and messages These names will be spoken over the telephone along with the item number that is normally spoken Voice descriptions for messages can be spoken over a speaker when used with the HAI Two Way Audio Module To enter the Set Up Voice menu from the Setup menu press the 8 VOICE key SET UP VOICE 1 CTRL 2 ZONE 3 BTTN 4 4 CODE 5 TEMP 6 AREA 8 MSG Select the item that you would like to give a voice description Use the arrow keys to scroll through the list of names To enter a voice description enter the code shown next to the voice description in Appendix C for each description word or group of words then press the key After you have entered the complete description for each item unit zone button code temperature area and message press the key twice You may enter up to six 6 descriptions word or group of words for each unit zone button code temperature area and message UNIT 1 VOICE UNIT 1 VOICE 144 109 4 When Unit is spoken over the phone the Omni will say UNIT 1 PORCH LIGHT Page 79 Set Up Address To record your address Press 9 then enter the Master code This is the address that the system says when it dials out in an emergency Your voice will be recorded on computer chips in the Omni controller and saved to be played back in the emergency message when the system dials out for an alarm Pick up an inside phone and press key
128. of the display will indicate what you are doing To the right of that is your selection or current setting The bottom line will show a menu of your next options To the lower right corner of the display is the direction arrow s Where possible the up 1 down 1 and two headed 1 arrow characters are shown on the console display to indicate which arrow keys may be pressed at that time Page 3 When using arrow keys to scroll through lists of areas buttons codes temperature zones units or zones only named items are displayed If no text description has been given to an item it will be skipped over when scrolling through that list You can still enter any item number to access it directly and then scroll up and down among the named items To look at another specific item simply enter the item number followed by the Down Arrow key In some cases the keypad keys 0 9 are assigned to different functions or menus A key assignment is indicated by the character key directly in front of the new function on the bottom line of the display For example if the bottom line says 2 DELETE you may press the 2 key to delete From the top level display each key functions as a menu choice Simply press the appropriate key and you will enter that menu Main Menu The main menu is entered from the top level display by pressing the key This menu displays all of the functions that you can perform from the console It is not neces
129. olice and Auxiliary are initiated with the simultaneous depression of two keys for approximately 1 second POL ERE eA NOTE The Emergency keys are always armed The Fire and Auxiliary emergency alarms are silenced by pressing the key To cancel a Police emergency alarm you must press the Off key and enter your code Page 11 Police Emergency When the 1 key and 3 key is pressed simultaneously the Police Emergency alarm is activated This alarm operates exactly the same as described for Burglar Alarm Activated except The console display indicates BURGLARY POLICE EMERG TRIPPED The interior sounder and the outdoor siren are activated immediately There is no outside siren delay Fire Emergency When the 4 key and the 6 key is pressed simultaneously the Fire Emergency alarm is activated This alarm operates exactly the same as described for Police Emergency Button except The sounders activates in a 3 pulse temporal pattern distinguish the fire alarm from the burglar alarm The console display will read FIRE ALM FIRE EMERG TRIPPED The Fire Emergency alarm be turned off at any time by pressing key Auxiliary Emergency When the 7 key and the 9 key is pressed simultaneously the Auxiliary Emergency alarm is activated The console beeper comes on display indicates AUX ALARM AUX EMG BTN TRIPPED console beeper continues to sound until the alarm is reset
130. olice immediately and tell them that a silent alarm has been activated at my address Thank you very much HOME PHONE OFFICE PHONE Page 85 APPENDIX TEXT DESCRIPTION CHARACTER CODES CODE CHAR CODE CHAR CODE CHAR CODE CHAR gt mN KK SB H I J K L M N 86 APPENDIX VOICE DESCRIPTION CODES DESCRIPTION ADDRESS MSG BEEP MEMO MESSAGE PAUSE SHORT PAUSE A M ABOVE AC POWER ACCESS ACTIVE ADDRESS AFTERNOON AIR ALARM ALERT ALL ALLEY AMPLIFIER AND ANNIVERSARY ANTIQUE APARTMENT APPLIANCE APPROACHING APRIL AREA ARMED ART ASLEEP ASSISTANCE AT ATRIUM ATTIC AUDIO AUGUST AUTO AUTOMATIC AUTOMATION AUXILIARY AWAKE AWAY BABY S BACK BANK BAR BARN BASEMENT BATH BATTERY BAY BED BELL BILL BIRTHDAY DESCRIPTION BOARD BOAT BOILER BOTTOM BOUDOIR BOY S BREAK BREAKFAST BRIGHTER BUILDING BURGLAR BUTTON BYPASS CABINET CABLE CALL CAMERA CANCEL CANS CARPORT CASE CCTV CD CEILING CELLAR CENTER CENTRAL CHANDELIER CHANGE CHECK CHILDREN S CHRISTMAS CIRCUIT CLASS CLOSE CLOSED CLOSET CODE COFFEE COLD COMFORT COMMUNICATOR COMPANY COMPUTER CONSOLE CONTACT CONTINUE CONTROL COOL CORNER COUNTER CRAFT CRITICAL CURRENT Page 87 DESCRIPTION CURTAIN DAMPER DANGER DATE DAY DEAD DECEMBER DECK DECREASE DEGREES DELAYED DEN DENIED DES
131. ommand or issuing a UPB Link command You are first prompted to specify whether the event button is for All Lights On All Off Leviton Scene or UPB Link ALL O OFF 1 ON 2 SCN 3 LINKY If area arming is being used you will be prompted to specify the desired area AREA ENTER AREA O ALL 4 If Leviton Scene is selected you must first specify the scene number ENTER SCENE 1 64 Then select the specified command Off On or Set If UPB Link is selected you must first specify the link number ENTER LINK 1 250 Then select the specified command Off On or Set Page 61 UPB Link Event Buttons When a program is created that uses When Link On as the trigger the program will execute when a Link Activate Link Goto as long as the result of the Goto command is not 0 or Link Fade Start as long as the result to the Fade command 15 not 0 message is received When a program is created that uses When Link Off as the trigger the program will execute when a Link Deactivate or Link Goto where the result of the Goto command is 0 message is received Using HAI PC Access Software you can create a program that uses When Link Fade Stop as the trigger When this trigger is used the program will execute when the Link Fade Stop message is received Alarm Event Buttons Pressing the 5 ALARM key allows you to specify an event button activated upon the occurr
132. one This command allows you to record and verify the address If an optional HAI Two Way Audio Module is being used this command also allows paging and listening to the premises Press 8 from the MAIN MENU to get to the PHONE menu PHONE PLEASE CHOOSE 3 INTERIOR 8 PLAY ADDRESS 9 RECORD ADDRESS CANCEL To play the current address press the 8 key To record the address press the 9 key and enter the Master code RECORD ADDRESS BEEP At the BEEP record your name and address ADDRESS IS OMNI PLAYS ADDRESS Note The address is used only for the VOICE dial out feature When the HAI Two Way Audio Module is being used To talk or listen to the premises press the 3 key PLEASE CHOOSE 2 TALK 8 LISTEN CANCEL Ifno key is pressed Omni will automatically switch to listen mode To talk to someone at the premises press the 2 key To listen to the premises press the 8 key You cannot talk to anyone on premises in listen mode and you cannot listen to the premises while in the talk mode 9 Good Bye Press 9 from the MAIN MENU The Omni will say GOOD BYE and hang up From an in house phone the dial tone will return From a remote phone you will hear a click as the Omni hangs up It is recommended that you press 9 to terminate a remote call If you don t the Omni will hang up anyway after about 15 seconds Panic Button over the Phone On an in house phone only you ca
133. onsole to turn off the security system even if you have to go through a room protected by a motion detector Some doors a back door or garage door may be configured as a Double or Quadruple Entry Delay If so that door has two times or four times the entry delay shown on the display ENTRY DELAY 30 30 60 SECONDS The default Entry Delay is 30 seconds You may change it from 30 to 60 seconds Page 71 Exit Delay The Exit Delay is the time in seconds that you have to leave your house when you turn on the system When arming the system in Day Night Away or Vacation modes the system will wait this amount of time before arming EXIT DELAY 60 45 180 SECONDS 1 The default Exit Delay is 60 seconds You may change it from 45 to 180 seconds Exit Time Restart When Exit Time Restart is set to Yes the Exit Delay will restart if the same exit zone is violated twice within the original exit delay For example after arming the system if you open the front door to leave close the front door behind you and then reenter through the front door while the exit delay is still in effect the exit delay will be restarted This is designed to give you additional time to exit without causing an alarm The exit time will only be restarted once within a given arming period To configure Exit Time Restart from the Set Up menu press the 5 ARM key EXIT TIME RESTART 1 1 YES The default setting for Exit Time Restart is Yes Unv
134. ooms X 10 Appliance Modules do not respond when the All Lights On command is sent All House Codes 1 4 by factory default respond to the All On command NOTE The On function can be changed if desired See Set Up Misc All On And All Off All Off At the ALL prompt press the 0 OFF key The console will beep and a command will be sent that turns off all specified X 10 and ALC units and HLC Rooms All House Codes 1 4 by factory default respond to the All Off command NOTE The All Off function can be changed if desired See Set Up Misc All On And All Off Leviton Scene Control Omni supports Leviton Scene Control a feature found in certain Leviton Switches There are 64 Scenes that can be set and executed The Leviton Switches are divided into lighting groups of four units each Each of these lighting groups can be set to four different Scenes Once the Scenes have been set up a command can be sent to the units in that Scene to simultaneously return to the preprogrammed lighting level Scene There are 64 Leviton Scenes that can be set and executed The X 10 units unit numbers 1 64 are divided into lighting groups of four units each Each of these lighting groups can be set to four different Scenes Scenes 1 4 apply to the first four unit numbers units 1 4 Scenes 5 8 to the next four unit numbers units 5 8 and so on Thus an easy correspondence is made between Scene numbers and unit numbers
135. or Trouble condition Voice Dialer In UL Listed Installations the Voice Dialer is supplementary to the Digital Dialer described above The voice dial out feature of the Omni is a sophisticated system that can notify you at the office on vacation on a pocket pager or notify your neighbor a relative and in some cases local authorities See What Happens When the Alarm is Activated also Set Up Dial How the Omni Voice Dialer Works When a Burglar Alarm fire alarm police emergency keys fire emergency keys auxiliary emergency keys gas alarm water alarm Temperature alarm or duress alarm is activated the voice dialer looks at the Dial Order to determine which numbers to dial and in what order A Dial Order can have up to 8 entries allowing the dialer to make up to 8 calls If you want it to try a number twice it can be entered twice in the dial order The dial order numbers can be chosen from Dial Out Numbers 1 8 What the Omni Voice Dialer Does When an alarm is activated the Omni will wait the Dial Out Delay If your system is monitored by central station it will be notified first Then the voice dialer will dial out to the numbers as described above If the alarm is turned off at the console while a voice dial out is in progress the dial out will be canceled immediately and the voice dialer will hang up If the number dialed is busy or if all lines are busy the dialer will immediately hang up and go to t
136. or example one keypad controller pushbutton can be linked to four UPB Wall Switches allowing the single press of that pushbutton to trigger all four lights to go to preset or absolute levels In addition UPB Wall Switches allow for a preset light level and fade rate to be associated with each Link Page 28 Activating and Deactivating Links A special UPB command called Link On activate is used to command all of the devices that have the same Link to go to their preset light levels at their preset fade rates For instance in our All On and All Off example when Link 50 is transmitted by Omni each UPB Wall Switch with Link 50 will go to 100 to achieve the All On effect Other Link On activate commands may be transmitted that cause Wall Switch 1 to go to a desired level at a specified fade rate and Wall Switch 2 to go to a different level at a different fade rate The ability to send more than one device to its preset level at a preset fade rate with a single command is known as activating a Link Likewise pressing a pushbutton on a 6 Button or 8 Button Keypad can send the Link On activate command A special UPB command called Link Off deactivate is used to command all of the devices that have the same Link to go to 0 at their preset fade rate For instance in our All On and All Off example when Link 50 Off is transmitted by Omni each Wall Switc
137. ou are on an in house phone hang up wait a few seconds then pick up and press the key To hear the main menu again press 0 on your phone To cancel an operation press for Cancel You will hear CANCEL and one beep for a cancel operation If you make a mistake you will hear 3 beeps then the Omni will re read whichever menu you are in Page 44 1 Control Press 1 from the MAIN MENU to get to the CONTROL menu If voice descriptions have been programmed after a three second delay the system will begin reading from the list of units Omni will say the unit number then its description The Omni will read three units then say PRESS POUND TO CONTINUE If the key is pressed Omni will read the next three unit numbers and descriptions if programmed 2 Security Press 2 from the MAIN MENU to get to the SECURITY menu From the Security menu you can arm your system Day Night Away Vacation Day Instant and Night Delayed disarm you system bypass and restore zones and go to a different area When bypassing and restoring a zone if voice descriptions have been programmed after a three second delay the system will begin reading from the list of zones If the key is pressed Omni will read the next three descriptions if programmed GOTO Area Press the key to GOTO a different area The Omni will say GOTO AREA ENTER AREA THEN ENTER CODE CANCEL WELCOME TO OMNI
138. pection authority or electrician as appropriate Notice The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le present appareil numerique n emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada IF YOU HAVE TROUBLE WITH YOUR PHONES and you suspect that your Omni is causing the trouble disconnect the Controller from the phone lines by removing PHONE LINE cable from BOTH THE PROCESSOR BOARD AND THE RJ31X JACK INSIDE THE CONTROLLER ENCLOSURE Page 83 APPENDIX A DIAL OUT PLANNER Use the following dial out planner to help you set up the voice dial out numbers Omni Voice Dial Out Planner DIAL OUT NUMBER 1 AREA DIAL OUT 1 ON TIME
139. phones Dial outs will still occur and the system will operate normally when the Omni dials out If you do not have your Omni connected to a phone line set Telephone Access to Off to keep the system from displaying PHONE LINE DEAD The default setting for Telephone Access is On Answer Outside Call If you do not want your system to Answer Outside Call set this item to No The local in house telephone control features will still work but the system will never answer an incoming call The default setting for Answer Outside Call is Yes Page 69 Remote Commands The Remote Commands Ok item allows you to prevent any commands from being issued from a remote telephone If Remote Commands Ok is set to Yes the Omni will allow all commands to be executed when called from a remote telephone If Remote Commands Ok is set to No then lights appliances and the security system cannot be controlled from a remote telephone that dials into your home You can issue commands from a local in house phone with Remote Commands Ok set to Yes or No The default setting is Yes Rings Before Answer Your phone must ring this number of times before the Omni will answer an incoming call to your phone To change Rings Before Answer enter the new number from 1 to 15 then press the key The factory default setting 15 8 Dial Type The Dial Type specifies the type of dialing used when the Omni dials out If you do not have Touc
140. rity Commands 65 Program Button Commands c ie s cccccvscscen se cescesie 66 Program All Off Commands 66 Program Video Commands E a EEE a E E 66 Program Temperature Commannd 0 cccccis ccecescectceccessssecssecsceddecsssedseinsdeccucessecuncescscuncentecotvecdecetdedieduasvadesdecenvedeesuasecddensdeceases 66 Program Energy Cost tees 66 Program Message 67 Program 5 67 Program Control 67 Program Security Mode Conditions c ccc5 cccciscccescescccescesdegescvdeciesedueiesseccucevsecuecensuccecescedtacetdecuccesdeduscvaeectecvtcedeedtadeccdensdecceses 68 Program Zone ste a EE 68 Program Time Clock Conditions 68 Program Other Conditions 68 Up ge 69 Telephone Access ien
141. rn all unit numbers in the specified House Codes on and off Note UPB CentraLite and RadioRA devices are not affected by the Omni All On or Off command To achieve this functionality we suggest the following UPB Program a Link into each device that will respond to an Omni On and All Off command program For example In each UPB switch that will respond to Off and program a Link in this example Link 50 is used that will go to 100 when activated turned on Then write the following programs in the Omni controller WHEN ALL ON LINK 50 ON WHEN ALL OFF LINK 50 OFF CentraLite Program the All and All Off macro to execute an All On Scene and an All Off Scene on the CentraLite RadioRA Program the All On and All Off macro to execute Phantom Button 16 All On and Phantom button 17 All Off For example WHEN ALL ON PHANTOM BUTTON 16 ON WHEN ALL OFF PHANTOM BUTTON 17 ON This All On Off menu is also used to control Leviton Scenes RadioRA Phantom Buttons UPB Links and CentraLite Scenes From the top level display or from the main menu press the 4 ALL key on the console keypad ALL 0 1 ON 2 SCN 3 LINKY ALL 4 PHANTOM 5 CENLIT 1 26 All Lights On At the ALL prompt press the 1 LIGHTS ON key The console will beep and a command will be sent that turns on all specified X 10 and ALC units and HLC R
142. roller will automatically exit Setup mode after 5 minutes To manually exit Setup mode press and hold the 1 and 8 pushbuttons simultaneously for at least 3 seconds Note When Omni Ile finishes configuring the device it will automatically exit Setup mode and return to normal operation Page 37 2 ZONE The Zone Status menu allows you to view and scroll through the status of each zone input To enter the Zone menu from the Status menu press the 2 ZONE key on the console keypad The system will display Front Door SECURE ZONE 1 You may enter a zone number to start displaying the status with zone or simply press the down arrow key to start with the first zone The arrow keys may be used to continue scrolling between zones For each zone the display will show the zone name the zone number and the current status of the zone 3 SUN SUNRISE SUNSET AUTOMATIC CALCULATION The system automatically calculates the time of sunrise and sunset each day From the status menu press the 3 SUN key on the console keypad to display the calculated time of sunrise sunset and the outdoor temperature if outdoor temp sensor installed Sunrise 6 00 AM Temp Sunset 5 58 PM 85 4 TEST SYSTEM DIAGNOSTIC TEST The diagnostic test performed by the Omni allows you to check the status of the battery telephone bell circuit auxiliary fuse and security zone loop readings The display is updated 3 times per second alt
143. rs if used in your system If you do not have a copy of these documents ask your installer See Underwriter s Laboratories Requirements In the event that there are any questions please call your installer first If you need assistance directly from the manufacturer call us at 504 736 9810 between the hours of 9 00 AM and 5 00 PM Central Time Monday Friday We will be happy to assist you When calling please have the model and serial number of your unit which can be found on the inside of the controller For your convenience we suggest that you record this information MODEL NUMBER SERIAL NUMBER Underwriter s Laboratories UL Listing The 20A00 50 51 and 52 Omni controllers and consoles have been tested and Listed by UL for the following applications UL 985 Household Fire Warning System Units e UL 1023 Household Burglar Alarm System Units Grade A The 20A00 51 Omni Ie controller has also been tested and Listed by UL for the following applications UL365 Police Station Connected Burglar Alarm Units and Systems Grade A UL 609 Local Burglar Alarm Units and Systems Grade A UL 1610 Central Station Burglar Alarm Units Grade In a UL Listed Installation failure to operate and program the system as described in this manual is a violation of the Listing Mark See Underwriter s Laboratories Requirements for more information Page 1 OVERALL DESCRIPTION Console Operation
144. s 4 HAI Communicating Thermostats Vv WV 8 PESMs or Voltage Outputs Omni also has 56 internal flags that are used for programming conditionals and executing programs About UPB UPB is a powerline communications standard for lighting and home control UPB is a robust two way digital powerline carrier communications protocol which transmits signals over the existing wires in a home UPB can coexist peacefully with X 10 systems intercoms baby monitors speakers etc that communicate over the powerline Using a Powerline Interface Module PIM Omni sends UPB commands over the existing electrical wiring to special switches modules and keypad controllers UPB devices that are designed with UPB technology UPB switches are two way devices so Omni knows the actual status of the switch when it is controlled locally In addition UPB switches modules and keypads can be used to trigger macros in the Omni controller Page 17 When set to UPB the Omni controller can Send commands on off bright dim and level to individual switches and modules Receive commands and status from individual switches and modules Send commands to keypad controllers to change scenes and control LED backlight behind the keys Receive commands when buttons are pressed on keypad controllers to activate controller macros Send Link commands to switches modules and keypad controllers to activate scenes Receive Link comm
145. s to the system When you press the 1 ADD key the Edit Program menu is displayed which allows the various parts of a program to be specified See Edit Program You may edit each part of the program as specified under Edit Program Press key at the Edit Program menu to show the newly entered program Press key again to save the program or press the key to return to the Edit Program menu to cancel entry of the new program and return to the Set Up Programs menu Once the new program is entered the display will return to the Set Up Programs menu 2 Show Programs The 2 SHOW key is used to review edit and delete existing programs From the Set Up Program menu press the 2 SHOW key The display prompts you to specify which program to be reviewed 1 CTRL 2 SEC 3 BTTN 4 ALL EVERY Menu 1 Programs for a particular control unit number Menu 2 All Security related programs Menu 3 Programs for a particular macro button Menu 4 Programs for All On Off functions Menu 5 Programs for a particular Temperature zone Menu Displays every program Selecting the 1 CTRL or 5 TEMP key will prompt you to specify the desired unit or temperature zone These can be specified by entering the number followed by the key or by using the arrow keys to scroll through a list of items UNIT ENTER UNIT TEMPERATURE ZONE ENTER TEMPERATURE ZONE J Selecting the 3 BTTN key will prompt you to specify the
146. sary to display the main menu before selecting a function if the number for the desired menu item is known The following menu choices are available 1 CONTROL 2 SECURITY 3 BUTTON 4 ALL 5 TEMP 6 STATUS 7 EVENTS 8 MESSAGE 9 SETUP Menu 1 Selects Control functions for controlling lights and appliances Menu 2 Selects Security functions arming disarming bypassing and restoring Menu 3 Allows a Button macro to be activated Menu 4 Selects All Lights On All Units Off commands and Leviton Scene Control commands Menu 5 Allows Temperature control for Thermostats and Energy Saver Modules Menu 6 Allows various status items to be displayed Menu 7 Allows you to view an event log of security happenings Menu 8 Allows you to show log clear say phone or send a message Menu 9 Allows you to enter setup mode for different operating configurations Error Beeps If you press a key that is invalid for the function that you are doing the console will beep 3 times indicating that it is not a valid option Look at the bottom line of the display to see what keys you can press next Trouble Beeps The Omni constantly checks the entire system for proper operation If trouble is found the trouble is displayed on the bottom line and the console will beep at the rate of two beeps per second to alert you to the trouble This feature can be turned off if desired See Set Up Arming Beep On Trouble To silen
147. ssage is activated Pro Link determines that a message has been received when One or more characters have been received followed by 100 ms of silence One or more characters followed by a carriage return character are received One or more characters followed by a line feed character are received It is not necessary to enter the terminating carriage return or line feed character as part of the message name Switch Press Event Buttons CentraLite When a button is pressed on a CentraLite keypad the When Switch program is activated Pressing the 9 SWITCH key allows you to select the When Command for a switch pressed activated event You are first prompted to enter the switch number SWITCH NUMBER 1 127 Enter switch number followed by key Edit Program Command Selecting 2 CMD from the Edit Program menu allows the commanded action for the program to be specified The following menu is displayed 1 CONTROL 2 SECURITY 3 BUTTON 4 ALL 5 TEMP 6 ENERGY 8 MESSAGE After command is specified display returns to Program menu Program Control Commands Press the 1 CONTROL key to command lights and appliances Specify the desired command See Control Porch Light Unit Name O OFF 1 ON 2 DIM 3 BRT 4 Porch Light Unit Name 4 LVL 5 RMP 9 TIM STAT If the selected unit is part of a House Code that is configured to use the Compose Format the second page of the
148. system dials out The Omni Ie will think that the tone is a code being entered by the called party and it will stop talking Page 80 UNDERWRITER S LABORATORIES REQUIREMENTS For a complete list of requirements and restrictions when installing the Omni panel in a UL Listed system refer to the Underwriter s Laboratories Requirements section of the Installation Manual 20100 50 When used in UL Listed Installations the following items apply The High Security Mode must be ON The Enable Auto Bypass feature must be OFF The Entry Delay shall not exceed 45 seconds for residential applications 60 seconds for commercial applications The Exit Delay shall not exceed 60 seconds Double Delay and Quad Delay zone types shall not be used For residential applications sounding device may be mounted indoors If however the sounding device is connected to the EXT HORN terminals of the Omni then the Outside Siren Delay shall be set to 0 The Dial Out Delay shall not exceed 30 seconds The Beep On Trouble feature must be ON and CONSOLE SOUNDER must be ON 9 Swinger Shutdown feature for each zone must be NO 10 The Cross Zoning feature for each zone must be NO 11 The Exit Time Restart feature must be NO Installer NAME NUMBER FIRE ESCAPE PLANNING Your fire protection system is designed to provide warn
149. te of the unit IF Porch Light O OFF 1 ON Program Security Mode Conditions Press the 2 SEC key to specify that the program should only execute if the security system is armed in a particular mode Select the security mode from the following menu O OFF 1 DAY 2 NIT 3 AWY 4 VAC 5 DYI 6 NTD Next select whether the system is considered in the specified mode during the exit delay INCLUDE EXIT DELAY O NO 1 YES If area arming is being used the display will then prompt you to specify the area Program Zone Conditions Select the 3 ZONE key to specify that the program should only execute if a specified security zone is either Secure or Not Ready The display prompts you for the zone number ZONE ENTER ZONE Enter zone number followed by the key or use arrow keys to select zone The zone will be displayed and you will be prompted for the state of the zone IF Front Door 0 SECURE 1 NOT RDY Program Time Clock Conditions Select the 9 TIME key to specify that the program should only execute if a specified Time Clock is either On or Off The display prompts you for the Time Clock number ENTER TIME CLOCK 1 3 Enter the Time Clock number followed by key Next specify the state of the time clock IF TIME CLOCK 1 O OFF 1 ON Program Other Conditions Select the OTHER key to select a condition from a list of other conditions SELECT CONDITION NONE 68
150. temperature below 40 degrees The alarm will not clear until the temperature exceeds 45 degrees When the alarm is initiated the console beeper will be turned on and an alarm dial out sequence will be initiated after the normal dial out delay Both voice and digital communicator dial outs may be used The voice dial out will follow the Dial Order as specified in Set Up Dial The digital communicator will report the Freeze Alarm Code to the Central Station The sounder is not activated for freeze alarms this feature must be activated by your installer Indoor and Outdoor Temperature The Model 31A00 1 Temperature Sensor is used for sensing temperatures from 0 F 120 F and 31A00 7 Extended Range Temperature Sensor is used for sensing temperatures from 40 F 120 F It features a new high accuracy temperature sensor that doesn t need calibration The temperature can be used to activate programs for controlling temperatures indoors and in attics garages greenhouses basements wine cellars coolers and freezers The temperature can be displayed on the console or spoken over the telephone It can also report log alert or generate an alarm if the temperature reaches freeze conditions or if the temperature goes above the high setpoint or drops below the low setpoint programmed in the system Outdoor temperature zones have a High and Low temperature associated with them that can be used for control purposes An example of this is to pro
151. that Scene to return to the lighting level set by the Scene Set command for that Scene Scene Off Command Once the Scenes have been sent press the 0 OFF key to command the four units in that Scene to turn off Notes 1 When sending Scene Commands the controller must be configured to allow Extended Code transmissions on each House Code affected by a Scene 2 Scene Commands always apply to a group of four consecutive units which units 1 4 5 8 9 12 and 13 16 particular house code You must address the units accordingly so that the desired units fall into the appropriate lighting groups 3 The actual Extended Code Scene commands use a group reference that matches that sent by a Leviton Wall Mounted Scene Controller set to the same address as the first unit in the lighting group This allows wall mounted controllers to be easily used for manual Scene selection UPB Links In a UPB network all control operations are done using Links Omni can transmit and receive up to 250 Links on the UPB network Links are used to logically connect events on one or more devices to actions on one or more other devices When two or more different devices share a common Link they are said to be linked together They can now communicate with each other over the powerline using the Link as a common identifier in all of their communications The power of Links is that you can link more than two devices together F
152. the Omni IIe hang up Hang up your phone and call your premises to be sure that it wasn t someone who has forgotten their code If not call the police If someone properly disarms the system while the called party is logged in then the status message will go back to SECURITY MODE IS OFF SYSTEM OK as described in Telephone Control If a reportable event an alarm cancel etc occurs while you are talking to your Omni Ie it will hang up on you to communicate the event to the central station Page 49 Access Omni is capable of communicating with an IBM compatible personal computer PC The can local in house remote The PC must be equipped with a modem or serial port and running PC Access software The Omni has a built in modem and can be accessed over the telephone or over a direct serial connection RS 232 RS 485 through either the built in or optional serial interface module If you wish to use your PC to configure program and check the status of your Omni Ile contact your dealer for the appropriate software for your PC Built In Ethernet Port The built in Ethernet port 16 allows a device to connect to the Omni controller via a network i e Ethernet Internet using a secure encrypted communication link The Ethernet port transports HAI application level packets containing Omni Link serial protocol messages over IP The controller supports 3 unique client sessions which means 3 devices m
153. the system and allow the phone to ring once or twice 2 Hang up 3 Wait about 10 seconds but within 60 seconds call the system again It will answer on the first ring and beep 4 Enter your code Main Menu Once you have successfully logged into your Omni it will read you a menu of commands as follows WELCOME TO OMNI AREA 1 PLEASE CHOOSE CONTROL SECURITY BUTTON ALL TEMPERATURE STATUS EVENT PHONE GOOD BYE CANCEL REPEAT ee eh This means that you press 1 for Control functions 2 for Security 3 for Button etc Pressing one of the keys on the phone will move you to another menu These menus are the same as the menus the console Words in brackets are only spoken if that feature is in use You do not have to wait for the Omni to finish talking Once you are familiar with the menus you can simply punch numbers on the phone without waiting Whenever you press a number the Omni stops talking and goes on to the function that you have selected If you press a key that is not on the current menu you will hear 3 beeps and the menu will be repeated So that the Omni does not tie up your phone there is a 10 to 15 second time out that starts after the Omni stops talking If it does not hear any numbers from your phone in 10 to 15 seconds after it stops talking the Omni will hang up If you are ona remote phone and the Omni hangs up you must call the Omni again If y
154. ting carriage return or line feed character as part of the message name Page 42 TELEPHONE CONTROL Telephone Interface Your Omni is equipped with a built in telephone response feature that allows you to control and access the status of your system from any Touch Tone phone The Omni actually talks to you using a digital recording of an actual human voice so the sound is incredibly life like You send commands to the Omni using the keys of your Touch Tone telephone There are no tapes discs or other moving parts associated with the speech and control features so there is no maintenance or parts to wear out Only Touch Tone phones will work with the Omni Some phones have switches that allow you to select Pulse or Tone Set them to Tone to work with the Omni NOTE There are two keys on your Touch Tone telephone that are special The key pound key to the right of the zero and the key star key to the left of the zero You will be using these keys In House Phones Each time you pick up your telephone at home the Omni will also pick up the line and listen for a pound key If Omni does not hear the key within 5 seconds it hangs up and does not listen in again until the next time you pick up your phone If the Omni hears any key other than the key while it is listening in it disconnects itself immediately If the Omni does hear the key within 3 seconds of your picking
155. ting up from zero The Set command is used to set the counter to a value from 0 to 255 No macros are executed when the counter is set to zero or when the counter is changed from zero using the set command This allows a counter to be reset without executing macros or programs associated with the counter counting to zero Turn the Flag On or Off to have the associated macro execute When the Flag is turned Off its value is set to zero 0 When the Flag is turned On its value is set to one 1 The counter is considered On for program conditions if it is nonzero 1 255 Flags can be turned Off On Decremented DEC Incremented INC Set and Timed ON OFF Controlling Outputs The Omni has eight outputs that can be used to switch relays Outputs 1 8 are controlled as Unit Numbers 65 72 respectively If the Interior Horn is configured as a General Purpose output Unit Number 73 is used to control the output If the Exterior Horn is configured as a General Purpose output Unit Number 74 is used to control the output In this configuration Unit Numbers 73 and 74 should not be used as Flags These 12 VDC voltage outputs are connected directly to the Omni He and not through a module If you have something connected to these outputs such as a sprinkler system your dealer will explain its operation Outputs cannot be brightened or dimmed and are not affected by All ON or All Off commands All On Off The All On Off menu is used to tu
156. troller will cycle power to reset smoke detectors The top line will display the security mode The bottom line will display ARMING SYSTEM to indicate that the system 15 being armed The system will be fully armed after the Exit Delay expires If arming in Away or Vacation mode gt gt Consoles configured with Audible Exit Delay enabled will beep until the Exit Delay has expired During the last 10 second of the Exit Delay the console will beep twice as fast so leave and close the door promptly If enabled Exit Time Restart will restart the exit delay if the same zone is violated twice within the original exit delay For example after arming the system if you open the front door to leave close the front door behind you and then reenter through the front door while the exit delay is still in effect the exit delay will be restarted This is designed to give you additional time to exit without causing an alarm The exit time will only be restarted once within a given arming period If Unvacated Premises is enabled if no exit zone is violated during the exit delay i e the premises was not vacated the system will automatically arm to Day mode at the expiration of the exit delay NOTE In Commercial Burglar Alarm Applications for UL Certified Systems a Ring back indication and Bell test should be heard after arming closing If not heard call for service Exit Error The Exit Error feature is design
157. ty system is Off Simply enter your Master or Manager code Your system was shipped from the factory with High Security Mode Off which allows you to view the event log and access the local phones without having to enter a code In most residential applications this is appropriate If you have a commercial installation or would like added protection from unauthorized access to the system you may wish to turn on High Security Mode Announce Alarms If the HAI Two Way Audio Module is being used in a system this item enables the system to speak the type of alarm and zone over a speaker on premises When an alarm first occurs the siren is activated After a few seconds the siren is turned off and the type of alarm is announced The siren is then reactivated The default for Announce Alarms is No Page 73 Enable Freeze Alarm If there are one or more Thermostat or PESM in a system they can also be used to detect a freeze condition See Freeze Alarm The default for Enabled Freeze Alarm is No Flash For Alarm You may enter one unit number that will flash on and off continuously when the alarm is activated This should be an outside light to alert neighbors and police to your property if the alarm is activated The default Flash For Alarm is Unit 2 You may enter one number for the unit number you wish to have flash 0 for none Console 1 8 Audible Exit Delay Consoles and touchscreens 1 8 can be configured to beep while the exit d
158. umber and then press the key Remember the code number It will not be redisplayed When entering a new code if the code that you enter already exists the console will beep three times and display INVALID CODE Enter a different code Authority Level Press key You will then be prompted for an authority level for that code CODE 2 AUTHORITY 3 1 MSTR 2 MGR 3 USER 1 AUTHORITY DESCRIPTION 1 Master Master codes have complete access to entire system Manager codes can arm and disarm areas that they have access to during assigned times Managers can 2 Manager i a Sr access the Main Menu if the system is in High Security Mode and have telephone access privilege 3 User User codes can only arm and disarm the system in assigned areas during assigned times Telephone access is not a privilege Page 53 Access Areas After an authority level has been entered you will be prompted for access areas for the user Specify which area s if part of your system the user has access to by pressing the number for each area The display will show all areas that have been enabled for that user After the area s is are selected press the key CODE 2 AREAS 12 You can specify access on off times for the code this is the time periods during which code is valid CODE 2 ON TIME 8 00 AM CHNG CODE 2 OFF TIME 5 00 PM MTWTF C
159. up the receiver it disconnects your phones from the phone company lines and connects your phones to itself and begins talking to you When you hang up your phones are immediately reconnected to the phone company You will hear a slight click on your phone when the Omni picks up or hangs up This is normal To access your Omni from an in house phone Pick up the receiver of any Touch Tone phone in your house Pause for just a moment about a second then press the key on the phone You will hear the voice read the menu which tells you what commands are available over the telephone NOTE If your system is in High Security Mode you must also enter your code following the key See High Security Mode In UL Listed Installations High Security Mode is enabled If the alarm system is tripped the in house phones will be disconnected when the Omni begins to dial out to preclude a burglar from jamming the line by shorting out an in house phone In this case you will have to turn the system off at the console Remote Phones You may call your system from any Touch Tone phone and talk to your Omni exactly as if you were at home except that you must enter your code Master or Manager to gain access to the Omni To call your system from any touch tone phone call your number After 8 rings or whatever you have Rings Before Answer set to your Omni will answer and beep See Set Up Dial Press the digits of yo
160. ur code on the phone The first digit must be pressed within 3 seconds of the beep You will hear the menu If you hear three beeps after entering the code you have entered the wrong code Try again If you make a mistake while entering the code press the key and then enter the code again You only have three tries to enter a valid code A successful remote access is logged in the event log as a Remote Phone Access along with the time date of its occurrence and the code number used There are a number of setup items that control what you can do from a remote phone when you or anyone else calls into your home See Set Up Dial Page 43 Phone Access Denied Remote Lockout The Omni has a remote lockout feature to discourage youngsters and adults who act that way from trying to access your system If four invalid codes are entered the system will hang up and a one hour lockout period will begin During the lockout period the Omni will not answer a call after any number of rings which should discourage the caller If a lockout occurs the event Phone Access Denied is entered into the event log along with the time and date of its occurrence The one hour lockout does not apply to in house phones The lockout is cleared immediately if the Omni is accessed using an in house phone Alternate Method The Omni has an alternate access method that may be more effective especially when calling long distance 1 Call
161. ut through specified Pro Link port exactly as message was entered Setup Names Message Carriage returns and line feed characters are not automatically appended to the end To send ASCII control as part of the message use the caret character in the message This character specifics that the next character is to be interpreted as an ASCII control character such as to represent a carriage return Other useful sequences would for a line feed character and G for a bell character To include an actual character in the message enter it twice as in Each message can be up to 15 characters long To send a longer message simply program two messages to be sent one after the other Pro Link also has the capability to monitor the serial port for incoming text messages When a text message is received Pro Link searches through all 64 messages for a matching message If one is found the Program Command macro corresponding to the matching message is activated When receiving an ASCII message that is over 15 characters Omni IIe only processes the last 15 characters of the message Pro Link determines that a message has been received when One or more characters have been received followed by 100 ms of silence e One or more characters followed by a carriage return character are received e One or more characters followed by a line feed character are received It is not necessary to enter the termina
162. vent buttons for the Day and Night modes are executed respectively Selecting 2 CODE allows you to specify that the event button is activated only when a particular code is used You will be prompted to enter the code ENTER USER CODE 1 16 O ALL 4 You should enter the user code by entering the code number followed by key by using the arrow keys to scroll through a list of code names WHEN C1 AWAY 1 DELAY 2 CODE 3 AREA Page 60 Selecting 3 AREA allows you to specify that the event button is activated only when specified area is armed disarmed You will be prompted to enter the area AREA ENTER AREA O ALL 4 The area number should be entered followed by the key or the arrow keys may be used to scroll through a list of areas WHEN C1 Al AWAY 1 DELAY 2 CODE 3 AREA Zone Event Buttons Pressing the 3 ZONE key allows you to select the event button for a zone activation event You are first prompted to enter the desired zone number ZONE ENTER ZONE The zone number should be entered followed by key or arrow keys may be used to scroll through a list of zones The desired zone is then displayed and you are prompted to specify the state that activates the event button WHEN Front Door 0 SECURE 1 NOT RDY All On Off Event Buttons Pressing the 4 ALL key allows you to specify an event button activated by issuing an All On or an All Off command issuing a Leviton Scene c
163. y entering the zone number followed by the key or by pressing the arrow keys to scroll through the list of temperature and humidity zones Press the key when the desired temperature zone is shown INDOOR HUMI 75 LOW 10 HIGH 90 Page 35 Status The Status function is used to display the status of various items in the system To enter the status menu from the top level display or the main menu press the 6 STATUS key on the console keypad STATUS 1 CTRL 2 ZONE 3 SUN JV 4 TEST 5 TEMP 6 ENERGY 1 CTRL CONTROL UNITS The Control Status menu allows you to view and scroll through the status of each control unit and to configure HLC and UPB devices To enter the Unit menu from the Status menu press the 1 CTRL key in the console keypad The system will display DEN LAMP STATUS OFF You may enter unit number to start displaying status of that unit or simply press down arrow key to scroll through list of units The status display is as shown under Control except that now the arrow keys may be used to continue scrolling between units Porch Light 00 24 19 LAST COMMANDED ON You can also check the state and if any remaining time duration of any Unit At this point you may press the key to control the unit as specified under Controlling Units or press to configure and HLC or UPB device Note Only HAI manufactured UPB devices collectively referred to as HLC devices can

20R00-50 Omni IIe Owner`s Manual V2.13

Contents

Download Pdf Manuals

Related Search

Related Contents