Wzzard SmartMesh IP Quick Start Guide
Contents
1. tightened to 5 in lb torque in order to maintain IP67 rating This can be accomplished via hand tightening ED check its After you have installed the batteries the LED will begin to blink This indicates that the Node is attempting to establish a network connection The LED will cease blinking when a connection is made Soil Or Module startup initialization approx 10 sec Slow Blink Attempting to establish connec 1 per sec tion with SmartMesh IP network Fast Blink 10 per sec Firmware Update in progress OFF Unit is connected to wireless network Install the Wzzard App on Your Handheld Device Install the Wzzard app on your Android or IOS handheld device Your handheld device must be compatible with Bluetooth LE 4 0 The Wzzard app can be downloaded from http bb smartsensing com Playstore Android or Apple Itunes app store Search stores for Wzzard Sensor Application 1 Open the Wzzard App 2 Press the Configuration button on the Node to wake up Bluetooth 3 Select the device you would like to view trom the list Note that the list may take a few moments to populate This screen lets the user view Bluetooth advertisements from the Nodes 4 Press the Configure Device button 5 Pair with the device Defaults are admin admin 6 Press the Radio Setup button to set the Network ID and Network Join Key These must be the same values that you enter i2. Enables publishing of the sensor data Sensor Enable On Off ON SCARS 0 20mA fio input kpe 430m OS SV The type of sensor connected to the input 1 5V a RTT User defined text field to describe the sensor Measurement Unit 8 characters Engineering unit of measure ET ra Polit 999999 9 to 5 0 The value that is reported when the P 999999 9 i input is at the maximum value Sensor Jaro Point 999999 9 to 0 0 The value that is reported when the Ee i input is at the minimum value Enables publishing of the sensor data Analog Inputs Enable Exception On Off On to the broker when an alert level eT 7 e node will send an update to Alert High AURRE the broker when the input exceeds 999999 9 this value 999999 9 to The node will send an update to the Alert Low broker when the input falls below 999999 9 ih oat d the node will P en enabled the node wi ae On Off On broadcast the sensor value over the Bluetooth interface Configuration Parameter Parameter Default Value Description Screen Range Sensor Enable On Off On Enables publishing of the sensor data to the broker User defined text field to describe Sensor Label 32 characters tempint the sensor Measurement Unit Cel degF Ce Engineering unit of measure Enables publishing of the sensor data Internal Enable Exception On Off On to the broker when an alert level Temperature is reached The node will send an update to Alert High pe the brok
3. Product Overview External Antenna Port Some Models Mounting Flanges Case Screws Internal Magnet in the base LED Configuration Button rig Connect Your Sensor Remove the 4 black screws that hold the top of the node in place Connect your sensor Conduit Models Analog and Digital Thread the included wire harness through the conduit and into the node Plug it into the circuit board inside the node 1 Brown 2 Red 3 Pink A Yellow 5 Green 6 Blue 7 White 9 Gray Connect your sensor to the wires running from the node s conduit Consult the chart on the other side of this page for wiring instructions M12 Models Analog and Digital with Accessory Cable 2 You can use your own 8 in M12 cable or order B amp B x 3 Electronics accessory SS WSCAMI2 6 7 N 4 pr 5 Consult the chart on the other side of this page for wiring instructions B amp B M12 Accessory Cable 1 White 2 Brown 3 Green 4 Yellow 5 Gray 6 Pink l 7 Blue 9 Red Terminal Block Connections Thermocouple Thread the thermocouple wires through the conduit and attach them to the terminal block 1 Thermocouple input 1 positive 2 Thermocouple input 1 negative 3 Thermocouple input 2 negative 4 Thermocouple input 2 positive O Install Your Batteries Use 2 3 6V 2400 mAH Lithium Thionyl Chloride AA batteries Replace the cover and tighten the 4 screws Screws must be
4. Pull force 4 7 Ibs 2 13 kg The magnet is in the base of the Wzzard node 77d Resetting the Node aeea BsB ELECTRONICS When you press and hold the Configuration button on the Node for more than 5 seconds it will Restore the BLE login and password encryption key encryption enable Restart the device It will not reset the device back to factory settings e M e mM e z o BsB ELECTRONICS Wzzard Intelligent Edge Node with SmartMesh IP and Bluetooth LE Device WSD2MA2 Fast Easy Answers Radio Setup Basic You can use your smart phone to access complete documentation on See Advanced Settings Network ID 1981 our website Simply Network Join Key A code to the VY First Things First Before you begin be sure you have Advertise During Sleep OFF the following Advertise Rate 0 00 10 O Wzzard Intelligent Edge Node Username admin E NaNe O Two Lithium Thionyl Chloride AA batteries Reesor e S MA RTW RX O External Antenna Some models 1 800 346 3119 Europe 353 91 792444 www bb elec com 707 Dayton Road PO Box 1040 Ottawa IL 61350 B B S Wipe Phone 815 433 5100 Fax 815 433 5109 MAI l ux o www bb elec com E mail info bb elec com Fast and easy on the web www bb elec com Doc Number 710 10263 00_RO_ Wzzard Smartmesh IP_4214qsg godna Electonics Mantiacioring Compay Wzzard Con
5. er when the input exceeds 999999 9 i ihe 7 Il send an update to th e node will send an update to the Alert Low PR broker when the input falls below 999999 9 this value BIE Advertisement When enabled the node will act On Off On broadcast the sensor value over the Bluetooth interface Configuration Parameter ue Default Value Description Screen Range ea On Off ON Enables publishing of the sensor data to the broker User defined text field to describe Sensor Label 32 characters vbatt the sensor Measurement Unit Cel degF Ce Engineering unit of measure Enables publishing of the sensor data Battery Enable Exception On Off On to the broker when an alert level Voltage l e node will send an update to Alert High P the broker when the input exceeds 999999 9 ihe E II send an update to th i e node will send an update to the Alert Low E broker when the input falls below 999999 9 this value BIE Advertisement When enabled the node will Enable On Off On broadcast the sensor value over the Bluetooth interface Configuration Parameter Parameter Screen Range Sensor Enable On Off ON Default Value Description Enables publishing of the sensor data to the broker User defined text field to describe Sensor Label 32 characters _ainx the sensor Engineering unit of measure When enabled the node will Measurement Unit 8 characters Accelerometer ee On Off On broadcast the sensor value o
6. figuration Charts Configuration Parameter Parameter Default Value Description Screen Range Unique identifier for the sensor Network ID 1 65534 1248 network This ID must match the peat he percent of time that the node will be awake A higher value allows the node to connect to the gateway faster but uses more battery current Join Duty Cycle 0 2 99 8 94 1 a2 Network Join Key hexadecimal EM SsuD network characters N Enables sensor broadcast messages Slee 3 On Off Enabled over the Bluetooth LE interface while P the node is asleep 10 86400 Advertise Rate 10 Interval between broadcast messages seconds Username 16 characters admin Login name for configuring the node Password 16 characters admin Password for configuring the node Configuration Parameter Parameter Screen Range Default Value Description Description ae User defined text field DEVICE ee 0 10 86400 0 Determines how frequently the node CONFIG eval seconds will wake up to check for an exception 10 seconds j bars Determines the interval between Publish Interval i oa 60 WEET EES Configuration Parameter Parameter Screen Range Default Value Description Latitude a p 0 0 Geographical location of the sensor GEO i Oto 180 LOCATION Longitude ees i 0 0 Geographical location of the sensor z 7 10 Elevation 999999 9 0 0 Elevation of the sensor Configuration Parameter J Default Value Description Screen Range
7. n the corresponding network gateway 7 Press the Save button to save the new settings Wiring for Units with Conduit Connectors and Attached Wiring Harness 6Blue 7 Whi GC lt P Q w o pand wo a gt o wn lt p D D ink WSD2CT WSDICJ WSD2 T AA WSDICT WSD2 A NSO voi o m wo mo w o aa wor o om m m w w oo WSD1CD N WSD2CA3 WSD1 CA ow WSBICTJ WSBICT AS WSBICA EE m m w w w oo NO Wiring for Units with M12 Connectors and B amp B M12 Accessory Cable 2 NO a a ou a 2 u ee 2 ee ee a Ee ee ee ee ee ee Ce Gl ee ee el a E ee oe ee ee ee ee ee ee N N m wa a J jf BRO P a t WSBIMT J WSBIMIK WSB1MA2 pand WSBIMD2 Wiring Chart Abbreviations 3 3V 3 3V power input 3 3REF 3 3V output reference AIN1 Analog Input 1 AIN2 Analog Input 2 AIN3 Analog Input 3 DO Digital Output DIN1 Digital Input 1 DIN2 Digital Input 2 DO1 Digital Output 1 DO2 Digital Output 2 O Configure the Node Refer to the Intelligent Edge Node User manual for further details and the App Configuration Manual for detailed configuration instructions O Mount the Node Flange Mounting Wzzard nodes may be mounted via their mounting ears M5 10 Magnetic Mounting Wzzard nodes contain a powerful internal mounting magnet
8. the sensor data to the broker when an alert level is reached The node will send an update to the broker when the input exceeds this value The node will send an update to the broker when the input falls below this value Changes the input from an active high input to an active low input hen enabled the node will broadcast the sensor value over the Bluetooth interface Message that is displayed when the boolean is true Message that is displayed when the boolean input is false The minimum amount of time that the input signal must be low or high before it is registered as a valid pulse Update frequency for the rate meter The scale factor for the counter and rate meter Description Enables publishing of the sensor data to the broker User defined text field to describe the sensor Inverts the level of the output When enabled the node will broadcast the sensor value over the Bluetooth interface B B SMARTWORx
9. ver the eaS Bluetooth interface N Measurement range of the accelerom Granula 26 46 86 4G eter A lower value will increase the sensitivity of the accelerometer 12 5 25 50 Frequency Response of the Accelerometer RE S accelerometer A higher value will 100 200 100Hz Interval 400H2 allow the accelerometer to capture faster events Configuration Screen Parameter Sensor Enable Sensor Label Measurement Unit Digital Input Type Enable Exception Alert High Digital Inputs Alert Low Invert Input BLE Advertisement Enable True Message False Message Minimum On Time Period Multiplier Configuration Parameter Screen Sensor Enable Sensor Label Digital Outputs p Output BLE Advertisement Enable Parameter Range On Off 32 characters 8 characters Boolean Count Rate On Off 999999 9 to 9999999 999999 9 to 999999 9 On Off On Off 8 characters 8 characters seconds seconds 999999 9 to 999999 9 Parameter Range On Off 32 characters On Off On Off Default Value ON dinx Boolean On On On 0 001 0 5 Default Value ON doutx off On Description Enables publishing of the sensor data to the broker User defined text field to describe the sensor Engineering unit of measure The type of sensor connected to the input either a boolean input a counter totalizer or a rate meter Enables publishing of
Download Pdf Manuals
Related Search