Home

Manual

1. Do not open the equipment and do not modify the equipment Do not connect this equipment to a dimmer pack Do not switch the equipment on and off in short intervals as this will reduce the system s life Only use the equipment indoors Do not expose to flammable sources liquids or gases Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable Make sure that the available voltage is between 220v 240v Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically e f the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again f the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e f your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS
2. e WARRANTY One year from date of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property LEDJ Spectra Batten Dip Switches Dip Switch settings All Dip Switches set to the off position Slow scroll through all of the programmes Dip Switch 1 only on Static Red 2 only on Static Green 1 2 on Static Blue 3 only on Static Cyan 1 3 on Static Yellow 2 3 on Static Purple 1 2 Static White With of the above static colours you can add a slow strobe with Dip Switch 7 or a fast strobe with Dip Switch 8 Dip Switch 4 only on Slow colour chase using the whole bar 4 1 on Slow colour chase with the bar in 3 segments 4 2 on Slow colour fade using the whole bar 4 3 on Slow colour fade with the bar in 3 segments 4 2 1 Slow colour chase with three multi coloured segments With any of the above chases or fades you can increase the speed with Dip Switch 5 slow or 6 fast Sound Activation For sound activation using the internal microphone set the Dip Switches as follows e Set Dip Switch 9 to the on positon and adjust
3. WWW PROLIGHT CO UK SPECTRA BATTEN ORDER CODE LEDwuU 75 ORDER CODE 7 5 LEDJ Spectra Batten Safety WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should 5 competent T Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty LEDJ Spectra Batten Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution Never remove warning or informative labels from the equipment
4. 372 404 436 118 150 182 214 us zn DABAN 406 438 470 502 151 216 312 376 408 440 472 124 DMX Address LEDJ Spectra Batten Specifications Spectra Batten Specifications e Input power AC240v 50Hz Power consumption 30w e LED s 240 Ultra bright 10mm LED s R 48 102 B 90 Beam angle 40 degree e Dimensions 1000 x 80 x 75mm Weight 4 2Kgs
5. used not not not LEDJ Spectra Batten DMX Set Up Notice Be sure to follow figures 2 amp 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out Vo DMX 512 in 3 pin XLR EU OA Sa Ww 3 pin XLR C XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground Pin 1 Ground 2 cold Pin 2 Negative 3Hot 3 Hot Pin 3 Postive FIGURE 3 FIGURE 2 Special Note Line termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behaviour Termination reduces signal transmission problems and interferance it is always advisable to connect a DMX terminal resistance 120 Ohm 1 4 W between 2 DMX and pin 3 DMX of the last fixture Using a cable terminator part number 90 will decrease the possibilities of erratic behaviour 5 Pin XLR DMX Connectors e Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The Chart below details the correct cable conversion 3 Pin XLR to 5 PIN XLR Conve
6. the sound sensitivity using a combination of Dip Switches 1 to 4 to set the desired level Slave mode e Set Dip Switch 10 only to the on position DMX mode Set Dip Switch 10 to the on position and use Dip Switches 1 to 9 to set the desired DMX address Fixture uses 12 DMX channels as shown on the next page Dip Switches LEDJ Spectra Batten DMX Address Setting DMX Settings CHI CH CH CH CH CH CH CH CH CH CH CH 6 7 9 10 1 12 3 lt 5 6 8 blackout SECTION 1 SECTION 2 SECTION 3 1 15 0 255 0 255 0 255 0 255 0 255 0 255 0 255 dimmer dimming strobe dimmer dimmer dimmer dimmer dimmer dimmer dimmer dimmer dimmer 1 all LED s d1 red2 green 2 blue2 red3 green3 blue 3 16 31 0 255 0 255 0 255 dimmer dimming strobe dimmer dimmer dimmer 2 all LED s all red all green all blue 32 47 not red used 48 63 not green used 64 79 not blue used no O O 80 95 t purple used 96 111 not yellow used SECTION 2 112 127 not 9 255 strobe SECTION 3 cyan used speed 128 143 not white used SECTION 1 144 159 colour 1 GROUND Yu 160 175 colour 176 191 0 255 0 255 colour fade strobe fade speed speed 192 207 multi INTERNAL MICROPHONE colour DMX IN DIP SWITCHES flow 208 223 0 255 fade select flow colour DMX OUT 224 239 two PUE colourl colour2 240 255 0 255 sound sound activated sensitivity used used
7. rsion Conductor 3 Pin XLR out 5 Pin XLR in Ground shield Pin 1 Pin 1 Negative Pin 2 Pin 2 Positive Pin 3 Pin 3 LEDJ Spectra Batten Dip Switch Reference Chart KUH a KAN ee Dip Switch position DMX Dip Switch Quick Reference Chart Dip Switch Position S2 84 a5 125 60 162 224 256 288 aa aka T 5s s sr 18 ter tes 26 257 285 Sar sss ase 417 us 2 oaee s Ta Tz vor 725 256 0 322 354 386 418 450 487 rs or ee wr ves ves i 38 68 00 132 14 sz 20 as ss ea a Fa a wine 135 167 1899 231 295 327 mmm 455 48 Fs 40 72 a 336 69 296 22 264 296 28 35 aa 5 137 ves aan 253 255 297 ws aa 0 ms 04 176 LIE 113 209 241 273 369 401 433 46 aor 434 La 1 cmn I Lid 8 F oo H n cn cn n3 mal Cat en RS re a 4 EEEEEL cu ji tad eT cn k i oo Cad j Ix c tad Ix t um 5 cg e 5 Paj Ix c mek cC T Ix i I a n i Pd qe Pa Lr EEI Lid ce Ca c I PJ 8 had EJE EJE Eak Ti Selo Poy Co co sl cn sil nin Po c on mel I co mek oo n3 na a ds

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents