3 Before starting the pressure washer
Contents
1. If the water being suctioned contains particles a suction filter must be mounted on the end of the hose In case of risk of running sands a sand filter must be attached oil light indicators will turn on 2 Move the throttle lever to SLOW or RUN position 3 Push the start button until the machine starts Now the charging oil light indicators will turn off If not stop the machine immediately and contact Gerni service department 4 The machine can be started by means of the starter rope if the battery has gone flat See manual from Yanmar Detergent can be added by means of the detergent injector 1 Dilute detergent according to the manufacturer s instructions 2 Set the pressure to the lowest setting on the lance CAUTION Never allow detergent to dry on the surface to be cleaned as this may cause damage 5 After using the washer 5 1 Stop the pressure washer Switching off POSEIDON DE Fea 3 5 2 Disconnecting supply lines 5 3 Storing the washer frost protected 1 Shut the fuel cock 2 Remove the water hose from the washer 1 Store the pressure washer in a dry room without danger of frost IMPORTANT If the high pressure washer is stored in a room with temperatures around or below 0 C anti freeze should be drawn into the pump beforehand 1 Remove the water inlet hose from the washer 2 Remove the lance2. 3 Start the washer and stop it again after max one minute 1 Stop the engine 2 Close the tap 3 Operate the spray gun until the wasser is depressurized 4 Lock the safety catch 1 Stop the washer by moving the throttle lever to STOP position 2 Switch off the ignition by pushing the ON OFF button The light indicators will now turn off 4 Connect the suction hose to the water inlet of the washer and place it in a tank containing anti freeze 5 Start the washer 6 Hold the spray gun over the tank containing anti freeze and activate it to start suction of anti freeze 7 During suction operate the spray gun two or three times 8 Lift the suction hose from the tank containing anti freeze and activate the spray gun to pump out the remaining anti freeze 9 Stop the washer 10 6 Maintenance 6 1 Maintenance plan pm every six months or as required 500 operating hours Maintenance of motor according to separate operating instructions from the engine supplier 6 2 Maintenance work 6 2 1 Clean water filter 6 2 2 Clean high pressure nozzle A water filter is fitted on the water inlet to prevent large particles of dirt from entering into the pump A blocked nozzle causes excessive pump pressure It must therefore be cleaned immediately 1 Stop the washer 2 Remove the lance 3 Clean the nozzle with a needle 4 Rinse the lance with water from the nozzle side 1
3. 8 3 Technical specifications Working pressure bar 140 140 230 195 Water volume Q l h 700 840 1150 1000 Water volume Qc Vh 650 750 1100 950 Cleaning impact kg Force 3 1 3 6 6 7 5 4 Max water inlet temperature C 60 60 70 70 Min max water inlet pressure bar 1 10 1 10 1 10 1 Dimensions x w x h mm 800x565x1010 1000x615x1150 Weight kg 35 38 68 110 Sound power level Lwa dB A 101 105 105 110 FEE 2 a level at spray m s lt 25 Thrust N 24 26 58 45 Suction height at max 8 C 1 1 5 1 1 Oil quantity in pump gear 0 18 0 18 0 56 0 27 0 56 0 27 Oil quantity in motor 0 6 0 6 1 1 1 65 Oil type motor pump gear SAE 15 40 We reserve the right to make alterations 8 4 EC Declaration of Conformity Description The design of the unit corresponds to the following pertinent regu Applied harmonised standards EN 55012 Applied national standards and technical specifications amp CV bun RE z Dipl Ing Wolfgang Nieuwkamp Test and Approvals High Pressure Washer Product POSEIDON 2 31 PE POSEIDON 3 36 PE Type POSEIDON 5 67 PE POSEIDON 5 54 DE 250 bar 20 MPa Petrol driven Diesel driven EEC Machine Directive EEC EMC Directive lations EN 2100 1 EN 12100 2 EN 60335 2 79 DIN EN 60335 2 79 C EC Declaration of Conformity 98 37 EEC 2004 108 EEC Bellenberg 01 12 2005 15 Nilfisk Advance Pty LTd 48 Egerto
4. Unscrew the union nut 2 Remove the filter and rinse it Replace damaged filter 3 Tighten the union nut gently so as to avoid damaging the gasket WARNING Use the cleaning needle only when the spray lance has been removed NOTE The fuel engine stops automatically if the oil level is low You can start the petrol engine again once you have added oil does not apply to POSEIDON 2 31 PE 11 1 Check whether the oil level is in the middle of the oil inspection glass Top up with oil if necessary See section 8 3 for type of oil 6 2 3 Checking the oil level 6 2 4 Changing the pump gear oil 1 Before changing the oil allow the pressure washer to become warm 2 Unscrew the plugs at the top and the bottom of the pump 3 Allow the oil to drain into a suitable container min 1 I capacity and dispose of oil in compliance with regulations 4 Mount plug at the bottom of the pump 5 Fill pump with fresh oil see 8 3 for oil type and quantity 6 Check the oil level see 6 2 3 12 7 Troubleshooting Fault Cause Remedy Pressure drop gt Air in the system gt High pressure nozzle blocked worn gt Pressure control on the lance is not set correctly gt Engine speed too low Vent the system by operating the spray gun several times at short intervals If necessary dismount the lance see section 4 2 2 Clean re
5. Low fuel level 8 Further information 8 1 Recycling the pressure w L 8 2 Warranty If the pressure washer is discarded make it unusable immediately 1 Dismount the ignition plug The pressure washer contains valuable materials that should Your Gerni product is guaranteed for 12 months from date of purchase purchase receipt must be presented on the following conditions e that defects are attributable to flaws or defects in materials or workmanship Usual wear and tear as well as misuse are not covered by the guarantee e that repairs have not been carried out or attempted by other than Gerni trained service staff e that only original accessories have been applied e Clean Fill the detergent tank e Adjust the lance to low pressure e Open fuel cock fill with fuel be recycled Contact your local waste disposal site If you have any queries please contact your local authorities or your nearest dealer e that the product has not been exposed to abuse such as knocks bumps or frost e that the instructions in the manual have been carefully observed A warranty repair comprises the replacement of defective parts but it does not cover freight and packaging charges Besides we refer to national Sale of Goods Act Any illegitimate guarantee repair will be invoiced l e malfunctions due to causes mentioned in section 7 Trouble shooting of the instruction manual 14
6. this machine in suction mode first ensure that the system has been bled of air by letting the In the case of poor water quality sand etc we recommend that a fine water filter is fitted in the water inlet Never expose the machine to an open flame Smoking is prohibited during fuelling Also read the operating manual for the fuel engine Note Never operate the machine in a closed room the exhaust fumes are dangerous Follow the safety instructions in chapter 1 1 Start the engine See the operating manual for the fuel engine 2 Unlock the spray gun and operate it 3 Lock the safety catch even during short pauses NOTE Operate the spray gun several times at short intervals to vent the system machine run without spray lance mounted until all air has escaped During work breaks of more than three minutes switch off the washer IEY For automatic suction from a tank watercourse or similar supply the inlet hose must be filled with water before you start The suction height depends on the water temperature Max suction height see section 8 3 Technical Data is reached with cold water up to 8 C With 70 C 60 C warm water the machine must be under or at the water level continued gt NOTE 4 2 3 Start POSEIDON PE 1 Switch on the ignition by pushing the ON OFF button of the machine The charging A As 4 3 Using detergents
7. Gerni danish cleaning power POSEIDON 2 31 3 36 5 67 PE POSEIDON 5 54 DE User Manual Copyright 2007 Gerni Contents Symbols 1 Important safety notes 2 Description 3 Before starting the pressure washer 4 Operation and use 5 After using the pressure washer 6 Maintenance 7 Troubleshooting 8 Further information 2 1 3 1 4 1 4 3 5 1 5 3 6 1 6 2 viele AO RAA aed ns tedden ne ee Gee 4 E ces astedueer tues TA E E S 6 Intended use 6 Operating elements 6 Setting up the pressure washer 7 Connections iii 7 Start the pressure washer asirinmi ariin a 8 Using detergents ce eeeeeeeeeeenneeeeeeeeneeeeeeeeneeeeeeeeneeeeeeeenaaees 9 Switching off the pressure washer 2 2111 2112 10 Disconnecting supply lines 10 Storing the cleaner frost free cceeceeeeeeeeeeeeeeeteeteeeeenees 10 Maintenance plan anans 11 Maintenance W rk i sassari AE a 11 D PAN 13 Recycling the pressure washer e eesaaaaaanauu2 14 DA ELLE OL ERO RPO 14 Technical specifications essay zaa a PAY 15 Declaration of Conformity aaa aaaa asia 15 Symbols Before starting up your high pressure washer for the first time this instruction manual must be read through carefully Save the instructions for later use Ci Safety instructions marked with this symbo
8. d lock it by turning it to the left 2 Insert the nipple of the lance into the quick coupling and turn the blue quick coupling grip to the right 3 Pull the lance or other accessory forward to check that it is securely attached to the spray gun NOTE Always remove any dirt from the nipple before connecting the lanse to the spray gun 1 Connect the high pressure hose to the high pressure inlet by means of the quick coupling Use max 50 m extension hose 2 Before connecting the water hose to the washer rinse the water hose briefly to prevent sand and other dirt from entering into the washer 3 Open the tap continued gt 7 4 1 3 4 2 4 2 1 4 2 2 IS Fuelling Start the washer Switching on the washer when it is connected to a water supply Switching on the washer when it is connected to open tanks suction mode NOTE See chapter 8 3 for required quantity of water and water pressure WARNING Always shut off the engine and let it cool for at least two minutes before fuelling Avoid spilling fuel If you do spill fuel when fuelling do not start the engine before the spilled fuel has evaporated If the washer is on a trailer any fuel spills must be wiped up before the machine is started 1 Before connecting the suction hose to the washer fill the hose with water 2 Start the washer 3 Unlock the spray gun and activate it 4 When using
9. e hose is damaged Never use the machine in areas where there is danger of fire or explosion When using the pressure washer stand at least 1 m from buildings etc Ensure an adequate air circulation Do not cover the washer or operate it in inadequately ventilated rooms The exhaust fumes are dangerous Store the pressure washer where it will not be exposed to frost Never operate the pressure washer without water Even brief shortages of water result in severe damage to the pump seals Maintenace and repair CAUTION Before cleaning and servicing the high pressure washer always remove the ignition plug cable first Carry out only the maintenance operations described in the operating instructions Use only original Gerni spare parts Do not make any technical modifications to the high pressure washer CAUTION High pressure hoses fittings and couplings are important for the safety of the washer Use only high pressure parts approved by the manufacturer CAUTION Failure to observe these instructions can endanger your safety Please contact the Gerni service department or an authorised specialist work shop for all other maintenance or repair work Testing The machine satisfies IEC EN 60335 2 79 standards The high pressure washer should be examined as needed or at least once a year by a technician to make sure that it is fail safe Our service technicians are at your disposal for ass
10. istance and advice Safety device The high pressure pump is equipped with a safety valve that redirects the by pass pressure back to the suction side of the pump The safety device is set and sealed at the factory and must not be adjusted 2 Description 2 1 2 2 Intended use This high pressure washer has been designed for professional use in agriculture transport industry construction industry etc Operating elements Start stop switch Lance Holder for lance 10 12 High pressure hose Spray gun inlet filter hose Pressure gauge Oil level gauge Filling of oil KASY PASZ Holder for high pressure hose Water conneciion and water Connection for high pressure Regulation of water volume 3 11 3 Before starting the pressure washer 3 1 Setting up the pressure washer 4 Operation and use 4 1 Connections 4 1 1 Connecting the lance to the spray gun 4 1 2 Connecting the high pressure hose and the water hose 1 Before using the pressure washer for the first time check it carefully to detect any faults or damage 2 In the event of any damage contact your Gerni dealer immediately 3 Check whether the oil level is in the middle of the oil inspection glass This also applies to machines with gear Pull the blue quick coupling of the spray gun forward an
11. l must be observed to prevent danger to persons 1 Important safety notes Before using the high pressure washer be sure to also read the enclosed operating instructions and keep them within reach at all times The high pressure washer may only be used by persons instructed in its use and who have been expressly authorised to do so General Use of the high pressure washer is subject to the applicable local regulations In addition to the operating instructions and the binding accident prevention regulations in the country of use the generally recognised rules for safe working must also be observed Any method of use endangering the safety of persons or equipment is forbidden Before use Before use check that the high pressure cleaner is in a safe and proper condition Operate the pressure washer only in an upright position Important notes Do not connect the pressure washer directly to the public drinking water mains observe DIN 1988 and EN 1717 A connection is permitted however e briefly to a pipe interrupter with moving section e with a free outlet Water may also be drawn from an open container or from a well or surface water not intended for the drinking water supply Please use suction set for this Ensure that neither dirty water nor liquids containing solvents are sucked in This symbol is used to mark safety instructions that must be observed to prevent damage to the
12. machine and its performance This symbol indicates tips and instructions to simplify work and to ensure a safe operation Please observe the regulations and provisions applicable in your country Before putting the high pressure washer into service carry out a visual check of all the major components High pressure jets can be dangerous if misused The jet must not be directed at persons animals live electrical equipment or the pressure washer itself During operation of the washer recoil forces are produced at the spray lance and when the lance is held at an angle a torque is also created The lance must therefore be held firmly in both hands Risk of injury Do not direct the jet towards yourself or towards other persons in order to clean clothes or footwear Do not use the washer when other people without protective clothing are in the working area Check that cleaning will not result in dangerous substances e g asbestos oil being washed off the object to be cleaned and harming the environment Do not clean delicate parts made of rubber fabric etc with the round jet Hold the nozzle at a distance of at least 15 cm when cleaning with the high pressure flat jet Although extremely easy to operate children should not be allowed to use the pressure washer Do not use the high pressure hose for lifting loads Do not continue to use the washer if the quick coupling or high pressur
13. n St Silverwater NSW 2128 106169230 01 2007 Phone 1300 556 710
14. place the high pressure nozzle Set the required working pressure Contact Gerni Service Department Pressure fluctuations In suction mode gt Lack of water gt Pump accessories partially frozen gt Water inlet hose is too long or its cross section too small gt Lack of water caused by blocked water filter gt Lack of water because max permissible suction height has not been heeded gt Water too hot gt Pump draws in air only possible in suction mode Open the tap Thaw machine and accessories Use prescribed size of water inlet hose Clean the water filter in the water connection never operate the machine without water filter mounted See chapter 4 2 2 See chapter 4 2 2 Check that the suction set is air tight Repeat aeration Excess pressure gt Engine s throttle control is defective accessory Give less gas contact Gerni Service Department The motor does not start gt Low fuel level gt Low oil level in engine gt The pump is blocked or frozen Open fuel cock fill with fuel Fill with oil Thaw machine contact Gerni Service Department 13 Fault Cause Remedy The motor stops gt Low oil level in engine e Fill with oil When a detergent injector is used gt Injector is dirty or suction hose is blocked gt Detergent tank is empty gt The lance is not set to low pressure gt
Download Pdf Manuals
Related Search