Home

User Manual - Laboratory ovens, furnaces

1. O 2012 Thermo Fisher Scientific Inc All rights reserved These operating instructions are protected by copyright Rights resulting thereof particularly reprint photomechanical or digital postprocessing or reproduction even in part are only allowed with the written consent of Thermo Fisher Sci entific This regulation does not apply to reproductions for in plant use The contents of this operating instructions manual may change at any time and without any prior notice In case of con flicting translations into foreign languages the German language version of these operating instructions shall be binding Trademarks Heratherm is a registered trademark of Thermo Scientific Thermo Scientific is a brand owned by Thermo Fisher Scientific Inc All other trademarks mentioned in the operating instructions are the exclusive property of the respective manufacturers Thermo Fisher Scientific Robert Bosch Strafe 1 D 63505 Langenselbold Germany Thermo Electron LED GmbH is an affiliate to Thermo Fisher Scientific Inc 81 Wyman Street Waltham MA 02454 USA Thermo Fisher Scientific Inc provides this document to its customers with a product purchase to use in the product oper ation This document is copyright protected and any reproduction of the whole or any part of this document is strictly prohibited except with the written authorization of Thermo Fisher Scientific Inc The contents of this document are subject t
2. If error does not go away call service power up alarm relay energized message shown on dis play Sensor Error E113 Sample sensor damaged Audible alarm activated Call service The actual measured value alarm relay energized is out of range message shown on dis play ADC Error E114 A D converter does not Audible alarm activated Call Service supply a plausible output alarm relay energized Measurement across refer message shown on dis ence resistor has failed play All control circuits dis ADC converter may be abled defective Watchdog error E115 Watchdog test failed on Audible alarm activated Call service Clearing should mute the audible alarm de energize the alarm relay and clear the message from the control panel display 12 4 Heratherm Thermo Scientific A Technical Data The technical data are valid only for an empty device equipped with three shelves a spray painted outer enclosure and a power line voltage 120 V 60 Hz Options may have an impact on the specified performance Table 13 1 Technical Data Series IMH 60 100 180 and IMH 60 S 100 S 180 S Parameter Unit IMH60 IMH100 IMH180 IMH60 S IMH100 S IMH 180 S Process first value is with fan off second with fan running Temperature deviation from set value at 37 C 99 F spatial Typical value K 0 6 0 2 0 6 0 3 0 6 0 4 0 6 0 2 0 6 0 3 0 6 0 4 Max value K X0 6 0 3 0 6 40 4 0
3. Access port Anti tilt anchor Electronics compartment Inlet air tube Hinge Door handle Display Nameplate on sidewall Exhaust air tube Fan Thermo Scientific hu L D o a a NB s s 4 e a amp us E E Hi o n q mu a a i c B 8 a E x E B a s B his a n 8 _ s g ts a a 8 E Pe 9 9 Figure 4 7 Heratherm IMH 750 S Front View Outer door Door hook catch Unit caster Air baffle Perforated shelf Door latch Glass door latch aniran 0 0 0 0 0 ee n N N e e A mn A A A SO ON OY MN dU Lb 2000 1 ON VA AWN e O o c cS o L C C Cc C cocco coao ca Thermo Scientific Temperature sensor Access port Glass door Fan opening air baffle Product Description Heratherm IMH S Incubator Overview Heratherm 4 9 Product Description Heratherm IMH S Incubator Overview Figure 4 8 Heratherm IMH 750 S Rear View Outer door N Unit caster Access port Anti tilt anchor Electronics compartment Hinge right Door handle Display Nameplate on sidewall Hinge left Inlet air tube Exhaust air tube Fan NNN BB a Re ee HOON AWA OD Ro f C Xo 060 JAN AD Ow odon a a a nm a re c ee 1 c C CC cC A ED A o a 4 10 Heratherm Thermo Scientific Product Description Safety Devices Safety Devices The incubators are equipped with the following safety features asample protection feature that safeguards the samples against destruction t
4. F 105 C 221 F 0 4 0 3 0 2 30 lt 3 lt 2 149 10 1655 65 2 1215 47 8 770 30 3 205 452 30 88 150 330 1560 13 0 1 N PE 60 Heratherm 13 3 Technical Data Table 13 2 Technical Data Series IMH 400 S IMH 750 S Parameter Power line voltage 10 IP protection system Protection class Overvoltage category as per IEC 60364 4 443 Device fusing building side Device fusing on PCB Environmental conditions Min ambient temperature Max ambient temperature Max humidity in service non condensing Min storage temperature Max storage temperature Max humidity in storage non condensing Post transport acclimation time Noise level Degree of pollution as per IEC EN 61010 1 Site conditions Maximum altitude above sea level Minimum side clearance Minimum front clearance Minimum back wall clearance Minimum top clearance 13 4 Heratherm Unit V CF CPF r F r H CPF CIF r F r H dB A m y ASL mm in mm in mm in mm in IMH 400 S IMH 750 S 120 IP 20 II 16 2x16 18 65 32 90 80 nicht kondensierend 20 68 60 140 90 nicht kondensierend 36 dB 2000 2187 50 2 810 31 9 120 4 7 200 7 9 670 26 4 Thermo Scientific Spare Parts and Accessories Material No Description 50126665 Stacking adapter Heratherm 60L 50126666 Stacking adapter Heratherm 100L 50126667 Stacking adapter Heratherm 18
5. Table 7 28 Setting Date and Time 2010 04 07 3 05PM Time Date 4 Set gt From the flashing Format Date menu item press A to switch to the Adjust option and confirm the selection with E The Adjust menu item is flashing in the multifunctional display pane now along with the day or year section depending on the selected date format of the date field in the upper left corner Press or to set the year and confirm your settings with Ss The flashing selection moves on to the month section of the date field Set months days or years hours and minutes using or and confirm each setting with LEN When you confirm with the button after setting the minutes the date and time field in the upper right corner will be updated according to your settings and stop flashing The display returns to its default mode The Settings icon in the menu bar will go out Temperature Display Unit The Settings gt C F menu item allows for toggling the incubator used for displaying temperatures between degrees Centigrade and Fahrenheit Table 7 29 Toggling the Temperature Display Unit Press to activate the menu bar then use or MENU to select the Settings icon and press ES to confirm 2010 04 06 1 33PM Error gt The Error menu item from the Settings submenu appears in the multifunctional display pane Thermo Scientific Heratherm 7 27 Handling and Control S
6. 6 40 5 0 6 40 3 0 6 40 4 0 6 0 5 Temperature deviation from set value at 37 C K 0 1 0 1 0 1 0 1 0 1 0 1 99 F over time Work space atmosphere Amb temp Amb temp Amb temp Amb temp Amb temp Amb temp Min C F plus plus plus plus plus plus 5 C 41 F 5 C 41 F 5 C 41 F 5 C A1 F 5 O A1 F 5 C A1 F Max C F 105 C 221 F 105 30 221 F 105 40 221 F 105 0 221 F 105 C 221 F 105 0 221 F Heat up time work space min 25 22 35 42 35 40 25 22 35 42 35 42 unoccupied from 25 C 77 F to 98 of set temperature of 37 C 98 6 F Max value typical value Recovery time work min 6 4 5 4 5 4 5 2 5 4 2 5 4 2 5 space unoccupied door open for 30 s to set temperature of 37 C 98 6 F Max value typical value Heat dissipation to W 23 65 30 68 36 78 23 65 30 68 36 78 environment at set 10 10 10 10 10 10 temperature of 37 C 98 6 F and room temperature of 25 C 77 F Overall dimensions Height mm in 720 820 920 720 820 920 28 3 32 3 36 2 28 3 32 3 36 2 Width mm in 530 640 640 530 640 640 20 8 25 2 25 2 20 8 25 2 25 2 Thermo Scientific Heratherm 13 1 Technical Data 13 2 Table 13 1 Technical Data Series IMH 60 100 180 and IMH 60 S 100 S 180 S Parameter Depth Overall weight Loading capacity per shelf Max overall loading capacity per device Electrical data Power consumption Maximum current Earthing system e g 1
7. Press to activate the menu bar then use UY to select the Timer icon and press to confirm 2010 03 29 12 59PM 4On Off Press to select the off timer option Off 2010 03 29 1 05PM Off Timer 2010 03 29 1 05Pm Set year month day hours and minutes using of followed by to confirm In the menu bar the Timer icon is illuminated and a hand is rotating on the icon s face Table 7 10 Setting a Fixed time On Timer Press to activate the menu bar then use to select the Timer icon and press to confirm 2010 03 29 12 59PM qOn Off MENU Press to select the on timer option On then to confirm 7 10 Heratherm Thermo Scientific Handling and Control Table 7 10 Setting a Fixed time On Timer 2010 03 29 1 05Pm On Timer 1 05pm 2010 03 29 Set year month day hours and minutes using oct followed by to confirm y The incubator switches off The display goes out the Timer icon is illuminated in the menu bar with a rotating hand on its face and the readiness indicator icon is illuminated additionally Setting a Weekly Timer Table 7 11 Presetting the Weekly Timer Mode of Operation Press to activate the menu bar then use to select the Settings icon and press to confirm Press to switch to the Timer menu item and confirm the selection with C3 2010 04 12 10 14pm Timer 4 Weekly p Press rR to select
8. The Error menu item from the Settings submenu appears in the multifunctional display pane Thermo Scientific Heratherm 7 23 Handling and Control Settings Table 7 25 Entering the Calibration Reference Temperature Manually 2010 04 06 1 33PM 4 Calibration Press to switch to the Calibration menu item and confirm the selection with SER 2010 04 06 1 33PM Calibration NECE In the Calibration selection screen press to choose the preselected option Manual 2010 04 06 1 33PM Calibration In the settings dialog that appears set the temperature measured with the external reference sensor by using or and confirm the settings with c3 36 9 C The newly entered value will be stored and used to calibrate the internal temperature sensors with the value measured by the reference sensor The display returns to its default mode The Settings icon in the menu bar will go out Date and Time The Settings gt Time Date option allows for switching between the international time and date display formats and for setting the time and date of the internal clock There are two display formats to choose from European date format DD MM YYYY and 24 hours time format Example 07 04 2010 and 15 05 US standard date format YYYY MM DD and 12 hour time format with AM PM suffix Example 2010 04 07 and 3 05 PM Table 7 26 Setting the Date Format Press to activate the menu b
9. and time Toggling the temperature display unit between C and F Entering a configuration control code Instructions for using these features are given in the following Also supported is an option for presetting the timer mode of operation as explained previously in the section Timer on page 7 8 Users calling customer service for support may be asked by the Thermo Fisher Scientific agent to supply information from the error log of the incubator This internal memory may be accessed by choosing the Settings gt Error menu item It enables the user to browse through the most recent 22 alarm messages that were caused by hardware or control loop errors Each error is displayed with the date and time of its occurrence a brief clear text description and an internal error code Error codes and instructions for clearing alarm conditions appear in the section Error Codes on page 12 1 Table 7 24 Reading the Error Log Press to activate the menu bar then use 23 or MENU to select the Settings icon and press E to confirm PP Press to select the Error item from the Settings submenu 4 Error gt Pa The first entry of the error log is displayed named Error 0 Error 0 2010 04 06 1 31PM Fan Error E009 Heratherm Thermo Scientific Handling and Control Settings Table 7 24 Reading the Error Log 2010 04 06 1 37pm Error 1 2010 04 06 1 34PM Heat Relay E109 Pre
10. display The device is completely inoperative Call service Disinfection Routine Error E006 Process error in decontam ination routine Controller heater or fan error etc Abort decontamination Audible alarm activated alarm relay energized message shown on dis play Acknowledge by pressing Co Relaunch decon tamination If this doesn t solve the problem call ser vice Thermo Scientific Heratherm Error Codes Table 12 1 Heratherm Incubator Error Codes Error Message amp Code Power Down Error E007 Root Cause Power has been cut off power outage while the device was running Alarm Response Audible alarm activated alarm relay energized message shown on dis play Alarm Clearing Instructions Check the power supply Power up then device then acknowledge the alarm by pressing co Fan Error E009 Fan speed out of range Audible alarm activated alarm relay energized message shown on dis play Heater disabled by controller Acknowledge by pressing Co If this doesn t solve the problem call service Config Error E012 General device configura tion error Audible alarm activated alarm relay energized message shown on dis play The device is com pletely inoperative Call service OTP error E013 Klixon contact not closed Overtemperature Protec tion fault Audible alarm activated alarm relay ener gi
11. incubators and heating amp drying ovens 50127447 Kit door handle with lock left Heratherm incubators and heating amp drying ovens 50127449 Temperature sensor for Heratherm incubators Thermo Scientific Heratherm 14 1 Spare Parts and Accessories 14 2 Material No Description 50127450 Upper door hinge for Heratherm incubators and heating amp drying ovens 50127451 Lower door hinge for Heratherm incubators and heating amp drying ovens 50127455 Outer door for Heratherm IGS 100 IMH 100 IMH 100 S OMS 100 OMH 100 OMH 100 S OGS 100 OGH 100 and OGH 100 S with a door stop on the right side 50127456 Outer door for Heratherm IGS 180 IMH 180 IMH 180 S OMS 180 OMH 180 OMH 180 S OGS 180 OGH 180 and OGH 180 S with a door stop on the right side 50127457 Kit operating panel Heratherm General Protocol incubators and heating amp drying ovens 50127458 Kit operating panel Heratherm Advanced Protocol and Advanced Protocol Security incubators and heating amp drying ovens 50127461 Kit electronic insert Heratherm General Protocol incubators and heating amp drying ovens 50127462 Kit electronic insert Heratherm Advanced Protocol and Advanced Protocol Security incubators and heating amp drying ovens without main board fan 50127463 Mainboard cable for Heratherm incubators and heating amp drying ovens 50127468 Glass door hinges for Heratherm incubat
12. instructions and hygiene guidelines Wear safety gloves Wear safety goggles Wear mouth and respiratory system protection gear to protect your mucous membranes Observe the safety instructions of the disinfectant s manufacturer and the hygiene supervisor 9 2 Heratherm Thermo Scientific Cleaning and Disinfection Wipe Spray Disinfection Predisinfection 1 Remove all samples from the work space and store them in a safe place 2 Spray disinfectant onto the surfaces of the work space and of the accessories or wipe the surfaces clean using disinfectant Risk of injury caused by breaking of glass panel The glass panel may only be removed by properly trained and authorized specialists The glass panel must be held by two persons 3 Allow time for the disinfectant to act as specified by the manufacturer N O TE Disinfecting hard to reach components Spray the sensor and other hard to reach components with disinfectant Thermo Scientific Heratherm 9 3 Cleaning and Disinfection Wipe Spray Disinfection Cleaning 1 Remove all internals from the specimen chamber 2 Wipe off the specimen chamber surfaces and the internals that have been removed from the chamber using lukewarm water mixed with standard rinsing agents Completely remove any tenacious impurities using rinsing agent and warm water 3 Re rinse the cleansed surfaces 3 to 5 times with autoclave
13. of one tenth of a degree up to 105 C 221 F e a variable speed work space fan adjustable on the control panel At high ambient temperatures the maximum speed is reduced countdown fixed time and weekly timers for timed process control two perforated shelves e an access port for tubing sensor leads etc power outlet Thermo Scientific Heratherm 4 1 Product Description Heratherm IMH Series Incubator Overview The individual features of IMH Series incubators are shown in the figures below Ga s 9 a2 39 AR 060000060 2 B a a E UR n Figure 4 1 Heratherm IMH 60 IMH 100 IMH 180 Front View Outer door Door latch cutout Door latch and handle Door hinge lower Levelling foot Nameplate Temperature sensor Support rail for perforated shelf Shelf support Fan opening air baffle Door hook catch Air baffle Door seal Stacking pad Spring Power outlet Access port rn L r mrm 5cc ccGxwu amp duot XO 00 ON VA 4 Q2 N2 A OSE CS CS CC I a en ee a ren Lr on c SS C IC NO ccc Glass door 4 2 Heratherm Thermo Scientific Product Description Heratherm IMH Series Incubator Overview F oN ON Unum ULbP p Lamp Pm Thermo Scientific igure 4 2 Heratherm IMH 60 IMH 100 IMH 180 Rear View Door latch and handle Control panel Stacking pad Access port Fan Electronics compartment Levelling foot Samp
14. process depends on the set temperature that is in place before decontamination is started on the initial temperature of the work space and miscellaneous other factors The incubator will be unavailable during that period of time Be sure to close off the access port with the provided closure plug before starting the decontamination routine Table 7 18 Launching Decontamination Press to activate the menu bar then use LZ to MENU select the Decontamination icon and press E to confirm 2010 03 31 1 34pm On ott In the selection screen that appears confirm the selected On option by pressing ES If a Stop Timer prompt appears while decontamination is launching If a timer is running an additional Stop Timer prompt appears at this point see Stopping an On Timer Before it Expires on page 7 13 When you answer that prompt with Yes the timer will be aborted and decontamination be launched instead Choosing No allows the timer to continue However if decontamination and a timer overlap decontamination has priority over the timer that is the timer will be put on hold and start later after the decontamination routine has finished 2010 03 31 1 34PM Decontamination Open door and check interior After pressing to launch decontamination you will be prompted to open the door and perform a safety check to make sure that all cultures or other temperature sensitive items have been removed fro
15. shelf table top incubators 2 Shelf support 4 Power cord 1 Connector potential free contact 1 Clip springs for table top incubators 2 Plug 1 Anti tilt anchor 1 Operating manual 1 Short reference guide 1 Heratherm Thermo Scientific O E Installation Ambient Conditions Location Requirements Built in incubators can heating and drying ovens must be operated with an air exhaust system and exhaust hose only original Thermo accessory should be used For safety reasons the installation space should be made of non combustible materials according to DIN 4102 During installation of built in units ensure that the N O TE escaping air will be safely discharged out of the installation space The incubator must only be operated in a location that meets all of the ambient condition requirements listed below Installation location indoors in dry areas free from drafts The dust burden may not exceed the contamination category 2 based on EN 61010 1 Using the incubator in an atmosphere with electrically conductive dust is prohibited The minimal distance to adjacent surfaces must be observed on all sides see Section Space Requirement on page 3 3 The operating room must be equipped with appropriate ventilation Solid level fire proof surface no flammable materials opposite to the rear panel of the incubator e Vibration proof substructure floor stand lab table capable of bearing the dead weight of the inc
16. specific days of the week The process for setting the preferences for this option is described in table 7 11 on page 7 11 while instructions for programming the daily turn on and turn off times are given in table 7 12 on page 7 11 Programming a turn on time causes the incubator to switch off until it is scheduled to restart while a turn off time keeps the device running before it shuts down at the user specified time The timer starts running immediately as soon as the user confirms his or her entries The decontamination routine see Decontamination on page 7 16 overrides timer schedules that is a pre programmed timer will not start before decontamination is finished Table 7 5 Presetting the Countdown Timer Mode of Operation Press to activate the menu bar then use QA to n select the Settings icon and press to confirm Press to switch to the Timer menu item and confirm the selection with c2 AE Press A or CB io select the Count Down timer mode of operation then use to confirm the Mets Berun gt selection The display returns to its default mode Thermo Scientific Handling and Control Timer Table 7 6 Setting a Countdown type off Timer Press to activate the menu bar then use 122 to select the Timer icon and press to confirm 2010 03 29 12 59Pm On Off gt Press to select the off timer option Off 2010 03 29 1 05pm Off Timer 00 00 Se
17. the Time Date menu item and confirm the selection with C23 2010 04 07 3 05PM Time Date 4 Date gt The Format Date menu item is flashing in the multifunctional display pane Thermo Scientific Heratherm 7 25 Handling and Control Settings Table 7 27 Setting the Time Format AA in the flashing Format Date menu item press to Time Date switch to the Format Time option and confirm the mE selection with 333 The Format Date menu item is flashing in the multifunctional display pane along with the time field in the upper right corner A Press or to switch to the desired time format a hh mm or hh mm AM PM and confirm the selection with 4 Time p The time field in the upper right corner will change its appearance according to your selection and stop flashing The display returns to its default mode n The Settings icon in the menu bar will go out Table 7 28 Setting Date and Time Press to activate the menu bar then use C23 or to select the Settings icon and press E to confirm rra The Error menu item from the Settings submenu appears in the multifunctional display pane 4 Error gt Sane Press to switch to the Time Date menu item and 4 Time Date confirm the selection with E The Format Date menu item is flashing in the multifunctional display pane Time Date 4 Date p 7 26 Heratherm Thermo Scientific Handling and Control Settings
18. the incubator for overall cleanliness and remove any residues from previous processes Check the locking screw for the glass panel To avoid incubator operation without an appropriate fresh air supply check the air filter optional in the air inlet path for contamination Semi annual Inspection Check integrity and proper seating of the seal Swap the fresh air filter accessory in air inlet Perform functional check of the control panel and of the incubator s built in controller Perform electrical safety check in accordance with the relevant national regulations Thermo Scientific Heratherm 10 1 Maintenance Service Intervals N O TE Functional Check If safety devices were removed or disabled for inspections the incubator must not be operated before the safety devices have been reinstalled and checked for their correct function A WARNING Spare Parts and User Modifications To avoid major malfunctions of the incubator and associated safety hazards that may result in death serious injuries or damage to the incubator and other equipment use spare parts approved by Thermo Scientific only Third party spares without Thermo Scientific approval void the limited warranty Do not modify the incubator in any way without obtaining the prior written authorization from Thermo Scientific Unauthorized modifications may compromise operational safety and give rise to hazards that may result in death serious injurie
19. 0L 50127146 Fresh air filter IMH IMH S 50127431 Outer door for Heratherm IGS 60 IMH 60 IMH 60 S OMS 60 OMH 60 OMH 60 S OGS 60 OGH 60 and OGH 60 S with a door stop on the left side 50127432 Outer door for Heratherm IGS 100 IMH 100 IMH 100 S OMS 100 OMH 100 OMH 100 S OGS 100 OGH 100 and OGH 100 S with a door stop on the left side 50127433 Outer door for Heratherm IGS 180 IMH 180 IMH 180 S OMS 180 OMH 180 OMH 180 S OGS 180 OGH 180 and OGH 180 S with a door stop on the left side 50127434 Outer door for Heratherm IGS 60 IMH 60 IMH 60 S OMS 60 OMH 60 OMH 60 S OGS 60 OGH 60 and OGH 60 S with a door stop on the right side 50127435 Staple feet Heratherm incubators and heating amp drying ovens 50127436 Kit door seal for Heratherm 60L 50127437 Kit door seal for Heratherm 100L 50127438 Kit door seal for Heratherm 180L 50127439 Kit door clips for Heratherm 60L 100L 180 L 50127440 Door inner panel seal for Heratherm IMH 60 and IMH 60 S 50127441 Door inner panel seal for Heratherm IMH 100 and IMH 100 S 50127442 Door inner panel seal for Heratherm IMH 180 and IMH 180 S 50127443 Levelling feet for Heratherm incubators and heating amp drying ovens 50127444 Kit door handle right Heratherm incubators and heating amp drying ovens 50127445 Kit door handle left Heratherm incubators and heating amp drying ovens 50127446 Kit door handle with lock right Heratherm
20. 11 00 c0 1 0011 08 31 07 10 d2 Date Time only 0012 00 c3 1 0012 08 01 02 23 dc 5 10 Heratherm Time Thermo Scientific Installation procedures Wiring the Alarm Contact Table 5 1 Terminal Commands for Querying Data Command Syntax Response Example Temperature Set Value T1 Current Work Space Temperature T2 Reference Temperature T3 Sample Sensor Temperature T4 3010 00 c2 1 3010 1f 125 00 124 96 000 000 000 00 b0 T1 T2 T3 T4 Wiring the Alarm Contact Skilled work Thermo Scientific warrants the operational safety and the operativeness of the incubator only if installation and repairs are performed by skilled personnel The connection of the incubator to an external alarm system must only be carried out by adequately trained and authorized electrical engineering or telecommunications expert personnel Functional Description When system errors and failures occur in the temperature control circuits an alarm message is issued to the connected alarm monitoring system The potential free contact single changeover type contact has been designed for the circuit configuration specified below NO TE Switching behavior The alarm relay is energized by all error conditions reported by internal control loops Alarm Relay Specifications Circuit Circuits with system voltage max 250 V SELV E circuits f VDEO100 Part 410 120V Thermo Scientific Heratherm
21. 5 11 Installation procedures Wiring the Alarm Contact Alarm contact electrical compatibility considerations To avoid overloading and damaging the alarm contact check the electrical interfacing parameters of the alarm receiving system for compatibility with the alarm relay specifications given above Connection Example The connector 5 for the interface cable is supplied with the incubator as a standard item Specifications for the operating voltage and the fusing of external alarm circuitry are given in the table above 1 Wire the individual conductors 1 through 4 of the interface cable as shown in the wiring diagram 2 Route the alarm cable along a path that does not cross hot exhaust air piping tables aisles or passageways With stacked devices keep the alarm cable away from hot spots on the other incubator in the stack 3 Plug the alarm system interface cable connector into the interface port 5 in the rear panel of the incubator M Figure 5 11 Alarm Contact Connection Example The circuit diagram shown above represents the undisturbed condition of operation In case of an error condition including a power outage contact closure occurs on the path between contacts 1 4 5 12 Heratherm Thermo Scientific CCC Operation Preparing the Incubator The incubator must not be released for operation before all major start up activiti
22. 80 and OMH 180 S 230 V 50127567 Fresh air filter for IMH IMH S 50127741 Support stand with castors for Heratherm 60L 50127742 Support stand with castors for Heratherm 100L 50127743 Support stand with castors for Heratherm 180L 50127764 Wire mesh shelf IGS 60 100 180 IMH 60 100 180 IMH 60 100 180 S including 2 shelf supports 50127768 Sample sensor for IMH 60 S IMH 100 S IMH 180 S 50127770 Stainless steel perforated shelf IGS 60 including 2 shelf supports 50127771 Stainless steel perforated shelf IGS 100 including 2 shelf supports 50127772 Stainless steel perforated shelf IGS 180 including 2 shelf supports 50127773 Stainless steel perforated shelf IMH 60 IMH 60 S OMH 60 OMH 60 S OMS 60 100 180 including 2 shelf supports 50127774 Stainless steel perforated shelf IMH 100 IMH 100 S OMH 100 OMH 100 S OMS 60 100 180 including 2 shelf supports 50127777 Stainless steel perforated shelf IMH 180 IMH 180 S OMH 180 OMH 180 S OMS 60 100 180 including 2 shelf supports 50127861 Retaining springs for Heratherm incubators and heating amp drying ovens 50127862 Support rail for Heratherm IGS 60 IMH 60 IMH 60 S OMS 60 OMH 60 OMH 60 S 50127863 Support rail for Heratherm IGS 100 IMH 100 IMH 100 S OMS 100 OMH 100 OMH 100 S 50127864 Support rail for Heratherm IGS 180 IMH 180 IMH 180 S OMS 180 OMH 180 OMH 180
23. 8962 Kit Shelving system with glass door lock IGS 180 IMH 180 IMH 180 S 50130657 Kit Viton door seal 60 L Heratherm 50130658 Kit Viton door seal 100 L Heratherm 50130659 Kit Viton door seal 180 L Heratherm 50134116 Kit Heating coil IGS 400 750 120 V centre 50134117 Kit Heating coil IGS 400 750 230 V centre 50134120 Kit Heating coil IGS 750 120 V outside 50134121 Kit Heating coil IGS 750 230 V outside 50134122 Kit Heating coil IMH 750 120 V ring heater 50134123 Kit heating coil IMH 750 230 V ring heater 50134315 Kit DS bus cable cpl 400 750 50134322 Kit glass door cpl 400 HTM 50134323 Kit glass door ri le cpl 750 HTM 50134326 Door gasket 400 L HTM 50134327 Door gasket 750 L HTM 50134328 Kit profile gasket 750 L HTM 50134329 Kit door conn clips 400 750 HTM 50134333 Kit castors 400 750 HTM 50134334 Kit shelf rack set cpl HTM 400 750 50135043 Kit electric insert cpl HTM H floorstand 50135044 Kit electric insert cpl HTM S floorstand 50135055 Kit electric insert cpl HTM 3 PH floor 50135056 Kit glass door hinges cpl 400 750 L HTM 50135058 Kit door lock 750 left cpl HTM Heratherm Thermo Scientific Material No 50135059 Spare Parts and Accessories Description Kit door lock 750 right cpl HTM 50135060 Door outer casing left HTM 400 50135061 Door outer casing right HTM 400 50135062 Door outer casing left HTM 750 50135063 Door outer casing right HTM 750 50135150 Kit temp sensor cpl
24. 90 23 2 690 27 2 814 32 80 3 2 Thermo Scientific Technical Data Table 13 1 Technical Data Series IMH 60 100 180 and IMH 60 S 100 S 180 S Parameter Unit IMH 60 Minimum bottom mm in clearance Minimum top clearance mm in IMH 100 IMH 180 200 8 300 12 Table 13 2 Technical Data Series IMH 400 S IMH 750 S Parameter Process Work space atmosphere Min Max Temperature deviation from set value at 37 C 99 F spatial Max value typical value Temperature deviation from set value at 37 C 99 F over time Heat up time work space unoccupied from 25 C 77 F to 98 of set temperature of 37 C 99 F Recovery time work space unoccupied door open for 30 s Max value Typical value Heat dissipation to environment at set temperature of 37 C 99 F and room temperature of 25 C 77 F Overall dimensions Height with casters Width Depth Overall weight Loading capacity Max overall loading capacity per device Electrical data Power rating Max Current Earthing system e g 1 N PE Power line frequency Thermo Scientific Unit IMH 400 S C F Amb temp plus 5 C 41 F C F 105 C 221 F K 0 3 0 2 K 0 2 min 35 min lt 3 lt 2 W 87 10 mm in 1655 65 2 mm in 755 29 7 mm in 770 30 3 kg lbs 145 320 kg lbs 30 66 kg lbs 75 1165 W 1380 A 11 5 1 N PE Hz IMH 60 S IMH 100 S IMH 180 S 200 8 300 12 IMH 750 S Amb temp plus 5 C 41
25. ARNING Risk of Burning on Hot Surface The surface around the tube access ports may become extremely hot Thermo Scientific Heratherm 4 17 Product Description Tube Access Ports 4 18 Heratherm Thermo Scientific A m Installation procedures Table top incubators Installing the Shelf System The installation of the shelf system does not require any tools The support rails are secured in place by spring action Once the shelf support brackets have been inserted into the rails the perforated shelves can be simply pushed onto their support hooks to complete the installation The support rails of the floor stand incubators cannot be removed Initial Installation 1 Peel off the protective foil from the support rails 2 Push the retaining spring 1 into the guide on the support rail 2 making sure that the locking nub 3 on the retaining spring safely engages with the matching hole in the support rail Figure 5 1 Sliding the Retaining Spring into the Support Rail Thermo Scientific Heratherm 5 1 Installation procedures Installing the Perforated Shelves Installing the Perforated Shelves The illustration below shows the placement of the shelf system elements 1 Air Baffles 2 Retaining Springs only for table top incubators 3 Support Rails 4 Shelf Support 5 Shelves Figure 5 2 Installing the Shelving Preparing the useable space Upon delivery Herat
26. H mm inch I mm inch 120 4 7 50 2 0 200 7 9 350 13 8 3 6 Heratherm Thermo Scientific Installation Transport Transport Table top incubators For transport do not lift the incubator using the doors or components attached to the incubator as lift points Figure 3 4 Lift Points NCAUTION Heavy loads Lift with care To avoid injury through physical strain such as strain traumata and slipped discs do not attempt to lift the incubator alone To avoid injury through dropped loads be sure to wear Personal Protection Equipment such as safety shoes when lifting the incubator To avoid crushing your fingers or hands particularly in a closing door or damaging the incubator do not use any other lift points than those indicated in the illustration above Thermo Scientific Heratherm 3 7 Installation Transport Floor stand incubators The floor stand incubators come equipped with four 4 casters The lever for releasing the caster is located above the locking lever After positioning the unit in its installation location ensure that the locking levers are pressed down on the casters To ensure the degree of stability specified by safety requirements the front casters must be turned so that they are facing forward after the unit has been positioned in its installation location and the locking levers pressed down on these casters Danger of tipping when moving Before moving the unit ensur
27. HTM incubator floor 50135153 Kit door lock 400 right cpl HTM 50135154 Thermo Scientific Kit door lock 400 left cpl HTM Heratherm 14 5 Spare Parts and Accessories 14 6 Heratherm Thermo Scientific Y A Device Log Incubator type Part number Serial number Service number Location Operator s note Work carried out Notes Date Signature Thermo Scientific Heratherm 15 1 Device Log 15 2 Heratherm Thermo Scientific LLL Contact Overview of Thermo Fisher International Sales Organization Postal address USA Thermo Scientific 275 Aiken Road Asheville NC 28804 USA Enquiries from USA Canada Sales 1 866 984 3766 Service 1 800 438 4851 Enquiries from Latin America Sales 1 866 984 3766 Service 1 866 984 3766 Enquiries from Asia China Sales 86 10 8419 3588 Service Toll free 8008105118 Support Mobile 4006505118 or 86 10 8419 3588 India Sales 91 22 6716 2200 Service Toll free 1 800 22 8374 or 91 22 6716 2200 Japan Sales 81 45 453 9220 Service 81 45 453 9224 Enquiries from the Rest of Asia Australia New Zealand Sales 852 2885 4613 Service 65 6872 9720 Enquiries from Countries not listed Rest of EMEA Sales 49 6184 90 6940 or 33 2 2803 2000 Service 49 6184 90 6940 Thermo Scientific Heratherm 16 1 Contact 16 2 Enquiries from Eur
28. Handling and Control Floor stand incubators Table 7 22 Turning on the Fan 03 04 2012 12 45 LT gt Press as often as needed to reach the second fan speed level then confirm with mm The multifunctional display pane will show the current fan speed level as a percentage 60 or 100 Additionally the matching number of chevrons will be illuminated in the bar graph to the right The display returns to its default mode The Fan icon in the menu bar is illuminated now to indicate that the fan is running Table 7 23 Adjusting Fan Speed or Turning the Fan Off table top incubators only Press to activate the menu bar then use or to select the Fan icon and press to confirm 03 04 2012 12 46 4 100 gt The settings dialog shown at left appears in the multifunctional display pane now with the current fan speed setting flashing already Change the fan speed with or ED then press to confirm The display returns to its default mode The fan continues to run until the unit is switched off Thermo Scientific Heratherm 7 21 Handling and Control Settings Error Log 7 22 Settings The Settings menu item opens a submenu populated with various commands for viewing general status information on the Heratherm unit and setting for the operation of the incubator or its display window Read access to error log e Calibrating the incubator Setting date
29. IMH 60 S 530 20 1 565 22 2 720 28 3 540 21 3 IMH 100 S 640 25 2 565 22 2 820 32 3 650 25 6 IMH 180 S 640 25 2 738 29 1 920 36 2 650 25 6 Depth of handle display 66 mm 2 6 in not included in overall depth specified height of adjustable feet 36 mm 1 4 in not included in overall height specified Table 3 2 Required Clearances E mm F mm G mm H mm 80 3 1 50 2 0 200 7 9 300 11 8 3 4 Heratherm Thermo Scientific Installation Room Ventilation Floor Stand Incubators 400 liter units WwW ec a Figure 3 2 Floor stand incubators dimensions and required clearances Table 3 3 Incubator Dimensions Model A mm inch B mm inch C mm inch D mm inch IMH 400 S 755 29 7 770 30 3 1655 65 2 810 31 9 Depth of handle display 66 mm 2 6 in not included in overall depth specified Width of hinge 23 mm not included in overall width Table 3 4 Required Clearances E mm inch F mm inch H mm inch mm inch 120 4 7 50 2 200 8 200 7 9 Thermo Scientific Heratherm 3 5 Installation Room Ventilation 750 liter units Figure 3 3 Floor stand incubators dimensions and required clearances Table 3 5 Incubator Dimensions Model A mm inch B mm inch C mm inch D mm inch IMH 750 S 1215 47 8 770 30 3 1655 65 2 670 26 4 Depth of handle display 66 mm 2 6 in not included in overall depth specified Width of hinge 23 mm not included in overall width Table 3 6 Required Clearances E mm inch F mm inch
30. N PE Power line frequency Power line voltage 10 IP protection system Protection class Overvoltage category Device fusing building side Device fusing on PCB Unit mm in kg lbs kg lbs kg lbs Hz Environmental conditions Min ambient temperature C F Max ambient temperature C F Max humidity in service non condensing Min storage temperature Max storage temperature Max humidity in storage non condensing Post transport acclimation time Noise level Pollution degree Site conditions Maximum altitude above sea level Minimum side clearance Minimum front clearance Minimum back wall clearance Heratherm r F r H C F C F r F 96 r H h dB A m y NN mm in mm in 590 23 2 690 27 2 814 32 mm in IMH 60 IMH 100 565 565 25 2 25 2 45 99 56 123 25 55 50 110 50 110 600 840 5 0 7 0 1 N PE 1 N PE 60 120 IP 20 Il 16 2x16 18 65 32 90 IMH 180 738 29 1 70 154 75 165 1020 8 5 1 N PE 80 non condensing 20 68 60 140 90 non condensing 45 2000 2187 50 2 80 3 2 IMH 60 S 565 25 2 45 99 50 110 1390 11 6 1 N PE IMH 100 S IMH 180 S 565 738 25 2 29 1 56 123 70 154 25 55 50 110 75 165 1390 1390 11 6 11 6 1 N PE 1 N PE 60 120 IP 20 Il 16 2x16 18 65 32 90 80 non condensing 20 68 60 140 90 non condensing 45 2000 2187 50 2 5
31. S 50128179 Kit Fuses T2A Incubators 120 V 50128184 Sample sensor connection for Heratherm incubators and heating amp drying ovens 50128197 Power socket for Heratherm IMH 50128203 Kit Fuses T2A Incubators 230 V 50128212 Fuse holder for Heratherm IMH 50128237 Kit Key for door handle with lock Heratherm 50128265 Lowenstein holder IGS 100 IMH 10 IMH 100 S IGS 180 IMH 180 IMH 180 S 50128683 Drip tray IGS IMH IMH S 60L 50128704 Kit Anti tilt anchor 50128791 Drip tray IGS IMH IMH S 100L 50128792 Thermo Scientific Drip tray IGS IMH IMH S 180L Heratherm 14 3 Spare Parts and Accessories 14 4 Material No Description Glass door lock for Heratherm IGS IMH und IMH S 50128793 Petri dish holder 50 mm 2 inch IGS 60 IMH 60 IMH 60 S 50128794 Petri dish holder 50 mm 2 inch IGS 100 IMH 100 IMH 100 S 50128815 Petri dish holder 50 mm 2 inch IGS 180 IMH 180 IMH 180 S 50128816 Petri dish holder 90 mm 3 54 inch IGS 60 IMH 60 IMH 60 S 50128818 Petri dish holder 90 mm 3 54 inch IGS 100 IMH 100 IMH 100 S 50128819 Petri dish holder 90 mm 3 54 inch IGS 180 IMH 180 IMH 180 S 50128960 Kit Shelving system with glass door lock IGS 60 IMH 60 IMH 60 S 50128961 Kit Shelving system with glass door lock IGS 100 IMH 100 IMH 100 S 5012
32. act M cr 4 13 PC POWer s 1 PTT 4 13 I C PC 4 13 Mones pato COPOS Aia 4 14 Inner aaa eite oe dere edet NN oda 4 14 Connecting Nozzles for Fresh air Filters Accessory Items eee 4 14 AECE PI A e dete A A ia 4 15 Tube Access Portu ide hd ree eee ee pe Eee ueniet ar eb IRE Ree aire eu cda ede 4 17 Installation procedures cS 5 1 Table t p incubators nod O n 5 1 Tistallinig the Shelf Systemi iere Oeo eie da vta decernimus 5 1 Initial Forse ll tdi dilo ias 5 1 Installine the Perforated Selves alo tidad E ehga 5 2 Preparing the useable paces 5 2 Installation or Removal of the Support Rails ciar di elas 5 3 Installing and Uninstalling the Aif Baflle dad iia 5 4 Lev lling the CUBO Rd ATR ER 5 4 Commissioning of floor stand cubital ia laca 5 5 Installing Removing air baffles IMH S Series usina lia ic 5 5 Comm ssioning AA eiaa ie aee aaia E n SA A a ASS 5 6 Installing the Shelf Support Brackets asno dci id 5 6 Tnstallino the Perforated Shelves conici A dit 5 7 Mains A AAA NI 5 7 Connecting to the Power Supply SOU dns 5 8 Connecting theRS 232 Interac cacaos lt ies rr ben aD 5 9 Interconnecting the Incubator with a Complet eee reo e nete treten aie sdasebichicabsnesdabonseias 5 9 Wiring the A TURION Gontact esnie tnos oa OA 5 11 Funcional escopeta ub scie ite 5 11 Alarm Relay Specifications moe A eese esci ode Duro loti o Ra cpu quin e adde tuse 5 11 Connection Examp
33. all service 12 2 Heratherm Thermo Scientific Table 12 1 Heratherm Incubator Error Codes Error Message amp Code Temperature Not Plau sible E103 Root Cause The difference between the control and reference sen sors exceeds the maximum permissible deviation ren dering the measurement implausible Alarm Response Device uses the sensor that indicates the higher temperature for servo con trol Audible alarm acti vated alarm relay energized message shown on display Error can be acknowledged and doesn t reset Error Codes Alarm Clearing Instructions If the error occurs repeat edly call service Calibration Value Too High E104 The calibration reference value calculated on the basis of the user input falls short of the upper limit for calibration references Fallback to previous cali bration reference Audible alarm activated alarm relay energized message shown on display Check the external refer ence sensor for proper function and replace if necessary If this does not solve the problem call ser vice Calibration Value Too low E105 The calibration reference value calculated on the basis of the user input exceeds the lower limit for calibration references Fall back to previous cali bration reference Audible alarm activated alarm relay energized message shown on display Check the external refer ence sensor for proper function and replace i
34. ally the incubator starts over with the decontamination cycle without any need for user intervention upon return of power Users who fail to notice the power outage may open the door and or load the incubator with samples thus exposing themselves or their samples to bio hazards without being aware of that risk The Decontamination icon in the menu bar is illuminated to indicate that the decontamination process is running Thermo Scientific Heratherm 7 17 Handling and Control Decontamination Table 7 18 Launching Decontamination When decontamination is completed the message Decontamination Decontamination finished appears in the multifunctional finished display pane Press the button to acknowledge that message The Decontamination icon in the menu bar will go out The settings that were in place before the decontamination routine was started for example fan speed will be restored Table 7 19 Stopping Decontamination Prematurely Press to activate the menu bar then use to select the Decontamination icon and press to confirm 2010 03 31 1 34pm In the selection screen that appears press Z to Quit Decon 4 No Yes switch to Yes and confirm the selection with The display returns to its default mode The Decontamination icon in the menu bar will go out The settings that were in place before the decontamination routine was started for example fan s
35. and the illuminated readiness indicator icon in the status display area indicates that the timer is running Instructions Timer on page 7 8 a 2 Power Outlet IMH Series only table top incubators only Toggles the AC outlet in the work space of the incubator on and off Instructions Power Outlet table top incubators only on page 7 15 7 4 Heratherm Thermo Scientific Handling and Control Table 7 3 Menu Bar Icons Icon Function Decontamination IMH S Series only Activates the built in decontamination routine Instructions Decontamination on page 7 16 Fan Turns the fan on and allows for choosing the fan speed levels described under D6 The current setting is shown by the bar graph located directly above the icon and spelled out as a numeric value in the display pane at D2 Instructions Fan on page 7 19 Settings Invokes a submenu with the following functions Read access to error log Calibrating the incubator Setting date and time Toggling the temperature display unit between C and F Selecting the timer mode of operation countdown fixed time of day weekday timer Entering a configuration control code Instructions Settings on page 7 22 Thermo Scientific Heratherm 7 5 Handling and Control Powering Up Powering Up 1 Plug the power plug of the incubator into a suitable protection earthed AC power outle
36. ar then use A or to select the Settings icon and press to confirm 2010 04 06 1 33PM 4 Error gt The Error menu item from the Settings submenu appears in the multifunctional display pane 7 24 Heratherm Thermo Scientific Handling and Control Settings Table 7 26 Setting the Date Format 2010 04 07 3 05PM 4 Time Date gt Press to switch to the Time Date menu item and confirm the selection with Ed 2010 04 07 3 05PM Time Date Date gt The Format Date menu item is flashing in the multifunctional display pane Choose the preselected option Format Date by pressing The date field will start flashing in the upper left corner of the multifunctional display pane 07 04 2010 3 05pm Time Date 4 Date gt Press or to switch to the desired date format DD MM YYYY or YYYY MM DD and confirm the selection with Ea The date field in the upper left corner will change its appearance according to your selection and stop flashing The display returns to its default mode The Settings icon in the menu bar will go out Table 7 27 Setting the Time Format Press to activate the menu bar then use or to select the Settings icon and press to confirm 2010 04 06 1 33PM Error gt The Error menu item from the Settings submenu appears in the multifunctional display pane 2010 04 07 3 05PM 4 Time Date gt Press to switch to
37. ave any questions regarding compliance with national standards regulations and directives applicable for your country please contact your Thermo Fisher Scientific sales organization 1 6 Heratherm Thermo Scientific ee Delivery of the Incubator Packaging Heratherm incubators are delivered in a rugged packaging box All packaging materials can be separated and are reusable Packaging materials Packaging carton Recycled paper Foam elements Styrofoam CFC free Pallet Chemically untreated wood Packaging film Polyethylene Packaging ribbons Polypropylene Acceptance Inspection After the incubator has been delivered check the delivery immediately for completeness possible damage If components are missing or damage is found on the incubator or the packaging in particular damage caused by humidity and or water please notify the carrier as well as Thermo Scientific Technical Support immediately ZA WARNING Risk of injury Should sharp edges have formed in damaged areas or elsewhere on the device take all necessary precautions to protect personnel handling the incubator For example have them wear protective gloves and other personal protection equipment Thermo Scientific Heratherm 2 1 Delivery of the Incubator Scope of Supply Scope of Supply 2 2 Incubators Quantity of components supplied pieces bett Perforated shelves 2 Support rail for
38. cting nozzle can be closed off using the 1 8 closure plug delivered with the unit after opening the plastic cap The connecting nozzle for the Heratherm IMH 60 100 180 and IMH 60 S 100 S 180 S incubators has a G 1 8 threaded fitting 4 14 Heratherm Thermo Scientific Product Description Work Space Components Figure 4 12 Connecting Nozzle for Fresh air Filters Accessory Item Access Port A re sealable capped access port can be closed off using the plugs delivered with the unit Heratherm IMH 60 100 180 and IMH 60 S 100 S 180 S 400 S 750 S only see figure 4 7 allows cables hoses or additional sensor leads to be routed into the work space of the incubator The access port 2 has a diameter of 42 mm NOTE Operating conditions When accessories are to be operated in the work space of the incubator the ambient condition requirements must be observed see table below The energy introduced into the work space has an impact on the lower end of the temperature control range When additional heating sources are introduced into the work space temperature control may be adversely affected Shelf System The incubator is supplied with two perforated shelves The shelf support rails 1 have an alternating pattern of oblong and round perforations spaced evenly at 30 mm allowing the shelf support brackets 8 to be inserted without any room for error yet in a very flexible way to accommodate any required hei
39. d IMH S Series incubators are shipped from the factory with the air baffle readily pre installed Before the air baffle can be removed from the back wall the support rails need to uninstalled DaoOpoogsO i Figure 5 4 Removing the Air Baffle 1 Losen the two screws 1 that hold the air baffle to the interior container back wall 2 Grab the two retaining springs 2 at their tabs and pull them downwards out of the embossings then take off the air baffle from the back wall 3 For the air baffle to install correctly the retaining springs must be facing upwards Place the air baffle on the lower embossings and tilt it upwards against the back wall of the work space 4 Clamp the two retaining springs 2 into the upper embossings 5 Secure the air baffle against the interior container back wall by fastening the two screws at 1 Levelling the Incubator 1 Position a bubble level onto the center shelf 2 Manually adjust the levelling feet until the shelf is horizontally aligned in all directions Perform the adjustment of the levelling feet from left to right and from rear to front 5 4 Heratherm Thermo Scientific Installation procedures Commissioning of floor stand incubators Commissioning of floor stand incubators Installing Removing air baffles IMH S Series The section below describes how to install remove the bottom plate Figure 5 5 Removing the bottom plate 1 Loosen and remove the fou
40. d water to completely remove any cleaning agent residues 4 After this wipe the cleansed surfaces and internals dry with a soft sterile cloth Final Disinfection 1 Spray the specimen chamber surfaces and the internals removed from this chamber again with disinfectant or wipe them down 2 Let the disinfectant work on the surfaces internals as detailed in the manufacturer s instructions 3 Re install the internals in the specimen chamber Starting the Decontamination Routine For detailed instructions please refer to Decontamination on page 7 16 only applicable for IMH S Series Be sure to close off the access port with the provided closure plug before starting the decontamination routine N O Js Recommendations for decontamination The user should be familiar with the internationally recognized Laboratory Biosafety Manual from the World Health Organization WHO and with national pertinent recommendations These manuals recommendations provide information about decontaminants their use dilution properties and possible applications NO TE Opening the door during the decontamination routine If the door will be opened and closed again whilst decontamination is running the routine returns to a phase which will ensure a continuation without faults 9 4 Heratherm Thermo Scientific Cleaning and Disinfection Wipe Spray Disinfection Be sure to determine the current op
41. ded when working with Heratherm incubators Warranty 1 2 Observe the sample weight limits specified for your Heratherm incubator as a whole and its shelving in particular see Technical Data on page 13 1 Do not load the bottom of the interior workspace to avoid the risk of overheating any samples placed there and to prevent the temperature sensor from being damaged Arrange the samples evenly throughout the work space making sure not to place them too closely to the interior walls to ensure a uniform temperature distribution Do not load your Heratherm incubator with substances that exceed the capabilities of the available lab apparatus and Personal Protection Equipment to provide sufficient degrees of protection to users and third parties Check the door seal every six months for proper sealing performance and possible damage Do not process any samples containing hazardous chemical substances that may be released into the ambient air through defective seals or may cause corrosion or other defects on parts of the Heratherm incubator Thermo Fisher Scientific warrants the operational safety and functions of the Heratherm incubators only under the condition that the incubator is operated and serviced exclusively in accordance with its intended purpose and as described in these operating instructions the incubator is not modified only original spare parts and accessories that have been approved by Thermo Scientific are us
42. e stacking adapter Fix the anti tilt anchor to a solid part of the building Floor stand incubators Heratherm floor stand incubators must always be attached to the wall using two 2 retaining brackets on the outer left and right side on the back of the unit Thermo Scientific Heratherm 3 11 Installation Installing the Anti tilt Anchor Remove the screws Attach the end of the retaining bracket that is facing downward to the unit Align the device at roughly 90 20 to the retaining bracket Affix the retaining bracket to the wall NCAUTION Unsafe part of the building Install the anti tilt anchor to a solid part of the building which is able for shoring loads The installation has to be carried out by qualified personnel only The connection to the building must be carried out with appropriate screws and dowels according to the consistence of the building part Additionally the following caution notes must be heeded at all times NCAUTION Risk of overheating with stacked devices To avoid the risk of electrical components and the outer enclosure overheating or temperature control failing due to insufficient ventilation do not exceed the specified stacking height A CAUTION Risk of tipping and dropping of stacked devices You should be aware at all times that stacked devices do not form a stable unit even when the stacking pads and frames are correctly used The top device may tip ove
43. e icon see table 7 3 on page 7 4 is highlighted by a red border to indicate that thermal protection has kicked in 4 12 Heratherm Thermo Scientific Product Description Data Communications amp Alarm Interface Data Communications amp Alarm Interface All signal connections are installed in the electrical interface panel at the rear of the incubator RS 232 Interface The RS 232 interface item 2 in figure 4 11 below may be used to connect Heratherm incubators to the serial interface port of a computer to allow for the computer aided acquisition and documentation of major operating parameters temperature error codes etc Sample Sensor connection only IMH S RS 232 interface Alarm contact Power socket 2fuses2 A for socket and lamp aero VA us GO Nm SSS Figure 4 11 Signal Interfaces and Power Socket Alarm Contact The incubator can be connected to an on site external alarm system such as a private branch telephone exchange a facility monitoring system visual or audible alarm indicators For this purpose the devices come with a pre wired potential free alarm contact item 3 in figure 4 11 The alarm contact is energized whenever an error occurs in an internal control loop or the incubator s electrical circuits or hardware AC Power Socket The incubator is connected to the AC supply mains via the socket item 4 in figure 4 11 which accepts a power cord with an IEC standard plug Fuses T
44. e power source 2 Connect the IEC connector to the socket at the rear of the incubator 3 Route the power cord along a path that does not cross exhaust air piping or passageways and aisles With stacked devices keep the power cord away from hot spots on the other incubator in the stack 4 Connect the protection earthed plug of the power cord to a correctly protection earthed and earth leakage circuit breaker fused power socket 5 Make sure the power cord is not subjected to tensile or compressive force N O TE Keep the power outlet accessible To allow a rapid disconnection of power in case of an emergency make sure that power outlets remain freely accessible at all times Figure 5 10 AC Power Supply Socket Condensation When taking the incubator into operation for the first time allow some time before switching on for stabilization to avoid condensation forming on live parts 5 8 Heratherm Thermo Scientific Installation procedures Connecting the RS 232 Interface Connecting the RS 232 Interface Replacement should only be carried out by skilled and authorized qualified personnel of electrotechnology signal engineering The RS 232 data communication interface supports the querying of status information and temperature data from the incubator by entering basic commands in a standard terminal window provided by your computer s operating system The interconnection
45. e that it has been unplugged Move the Heratherm floor stand incubators with caution Quick starts and stops can result in tipping Always ensure that the doors are closed when moving the unit 3 8 Heratherm Thermo Scientific Installation Stacking kit Stacking kit The stacking adapter is available only for table top incubators Material Number Description 50126665 Stacking adapter Heratherm 60L 50126666 Stacking adapter Heratherm 100L 50126667 Stacking adapter Heratherm 180L Scope of delivery 1 Stacking adapter 1 Anti tilt anchor 1 Plastic bag with 2 stacking feet and 2 M x16 Torx screws Required Tools Slotted screwdriver 5 5x100 or Torx screwdriver 20x100 Installing the Stacking Feet Remove the left and right blank plugs at the top Install the stacking feet with the enclosed screws using a slotted or Torx screwdriver Thermo Scientific Heratherm 3 9 Installation Installing the Stacking Adapter Installing the Stacking Adapter 1 Anti tilt anchor Stack as follows when using a stacking adapter numbers denote incubator volumes in liters e for 601 or 100 l on 180 use stacking adapter Heratherm 180L e for 601 on 1001 use stacking adapter Heratherm100L To prevent the top device from slipping and dropping down the following requirements must be fulfilled before devices may be stacked Only two units may be stacked together When stacking devices with the
46. ed third party spares without Thermo Scientific approval void the limited warranty inspections and maintenance are performed at the specified intervals an operation verification test is performed after each repair activity The warranty is valid from the date of delivery of the incubator to the customer Heratherm Thermo Scientific Satety Notes Explanation of Safety Information and Symbols Explanation of Safety Information and Symbols Safety Notes and Symbols Used Throughout These Operating Instructions Indicates a hazardous situation which if not avoided will result in death or serious injuries Indicates a hazardous situation which if not avoided could result in death or serious injuries Indicates a situation which if not avoided could result in damage to equipment or property NOTE Is used for useful hints and information regarding the application Thermo Scientific Heratherm 1 3 Safety Notes Explanation of Safety Information and Symbols Additional Symbols for Safety Information 1 4 Wear safety gloves Wear safety goggles Harmful liquids Electric shock Hot surfaces Fire hazard Explosion hazard Suffocation hazard Biological hazard Contamination hazard Dope e FL ew O a Danger of tipping Heratherm Thermo Scientific Safety Notes Explanation of Safety Information and Symbol
47. er value for example the temperature set value in D5 or the fan speed level at D6 Hold ing this button depressed for a few seconds changes the selected value in quick run mode Moves the selection in the multifunctional display pane in D2 in the currently activated menu item to the next option on the left for example from the Off state of the timer to On K3 On Off Button Holding this button depressed for 2 seconds switches the incu bator off The display window goes out except for the readiness indicator icon in the status display area at item D4 The temperature display field D1 provides a dimmed readout of the work space temperature provided that the temperature exceeds 50 C 122 F K4 Right button After the first press of Menu Enter button Moves the selection in the menu see item D3 to the next icon on the right Once a menu item has been selected Increases an adjustable parameter value for example the temperature set value in D5 or the fan speed level at D6 Hold ing this button depressed for a few seconds changes the selected value in quick run mode Moves the selection in the multifunctional display pane in D2 in the currently activated menu item to the next option on the left for example from the Off state of the timer to On K5 Escape button E3 Returns to the previous level of the menu or standard display Upon exiting from the current menu item the user may be prompted to save any previou
48. erating condition of the incubator before you open the door Under specific circumstances there is a risk that bacteria viruses fungi prions and other biological substances survive when the decontamination routine is aborted due to a power outage Normally the incubator starts over with the decontamination cycle without any need for user intervention upon return of power Users who fail to notice the power outage may open the door and or load the incubator with samples thus exposing themselves or their samples to bio hazards without being aware of that risk Decontamination must be performed immediately if any biohazardous material is spilled in or on the incubator Thermo Scientific Heratherm 9 5 Cleaning and Disinfection Wipe Spray Disinfection 9 6 Heratherm Thermo Scientific LLL Em Maintenance Maintenance and inspection at regular intervals of the features and components listed below are mission critical to maintain the product in a fully operative and safe condition and avoid malfunctions due to ageing and wear Failure to perform maintenance on a regular basis may result in deviations in heating performance damage to samples loss of control over temperature distribution throughout the work space Inspections and Checks To ensure the operational performance and safety of the incubator and its functions the components listed below must be checked at regular intervals Regular Checks Check
49. erm Incubator Error Codes Error Message amp Code Heating Triac Error E110 Root Cause The voltage measurement has indicated a defect in the triac Alarm Response Audible alarm activated alarm relay energized message shown on dis play Overheat protection activated to prevent destruction of the samples Audible alarm returns upon acknowledgement Alarm Clearing Instructions Call service and switch the device off Temperature Too High E111 The actual measured value exceeds the upper limit of the permissible error range Audible alarm activated alarm relay energized message shown on dis play Heater turned off until upper limit of hysteresis is recovered Servo control operations continue Alarm can be acknowledged and goes away when the differ ence between the actual and set values ceases to exist Note This error does not indicate a defective triac Open the door to speed up cool down Check whether the device was loaded with a hot object if so remove Ensure that the equipment was operated with at least one perforated shelve and with the door not opened longer than 10 min If this doesn t solve the problem call service Sensor Error E112 The measured actual value is out of range Audible alarm activated alarm relay energized message shown on dis play Control continues on process sensor If both sensors are defective all control circuits will be dis abled
50. es have been completed see Installation procedures on page 5 1 Device Check Prior to starting operation the following incubator components must be checked for their correct function The door seal in the front frame must not be damaged The glass door must not be damaged The shelving components must be installed safely e Disinfecting the Incubators Work Space Run the decontamination routine Heratherm IMH 60 100 180 400 750 S devices only see section Decontamination on page 7 16 or disinfect the work space according to the operator specified hygiene guidelines Starting Operation 1 Turn the incubator on using the control panel 2 Adjust the temperature set value on the control panel 3 Launch decontamination optional with Heratherm IMH 60 100 180 400 750 S devices only see Decontamination on page 7 16 4 The temperature controller starts adjusting the work space to the user specified temperature set value now Thermo Scientific Heratherm 6 1 Operation Starting Operation y To avoid any risk of explosion or fire Ja E e refrain from loading the incubator with any of the substances listed in the section Incorrect Use on page 1 6 make sure that the ambient air is free of any solvents do not operate the incubator in areas with an explosion hazard 6 Load the work space with samples 7 r j a c Hot surfaces The screen of the g
51. ettings Table 7 29 Toggling the Temperature Display Unit a Press to switch to the C F menu item and MENU c i F confirm the selection with E Pra Ihemultifunctional display pane changes to the following selection screen with the currently unused temperature display unit factory setting is C flashing Confirm the selection with BEN C F dec p gt 2010 04 07 10 31am C F F The temperatures in the display field item D1 in figure 7 1 on page 7 1 and settings pane Set item D5 in the same figure will be displayed with the newly selected unit The display returns to its default mode The Settings icon in the menu bar will go out 7 28 Heratherm Thermo Scientific EN E Shut down Shutting the Incubator Down This chapter provides instructions for shutting the incubator down for prolonged periods of time that is at least for several days in a row A WARNING Contamination hazard If the work space surfaces are contaminated harmful biological material may spread to the environment of the incubator To rule out any risk for subsequent users perform a full cleaning disinfection and decontamination cycle to the standards set out in the section Cleaning and Disinfection on page 9 1 if you suspect or if you are positive that harmful biological material has been processed with the incubator 1 Remove the containers wi
52. eyna bert b aUa RERUM I LM E Ge 5 1 Figure 5 2 Installing the Shelving aran AAA TRIP RS QN Pap Ve t UAE VEDI dan RI 5 2 Figure 5 3 Support Rail Installations MT 5 3 Figure 5 4 Removing the Air Baffle dt is 5 4 Figure 5 5 Removing the b ttom plate sia isih ireid s pud eg bae RUE 5 5 Figure 5 6 Removing the left and right support profiles inanici n 5 5 Figure 5 7 Removing the rear air baffle IMH 400 S 730 8 sacd iii 5 6 Figure 5 8 Shelf Support Bracket Installation an idea 5 6 Figure 5 9 Perforated Shelf iaria lado aeaa a a AE artesa A ed RETETE 5 7 Figure 5 10 AC Power Supply Ora neiii Fita dU airaa EE AAE EEEE 5 8 Figure 5 11 Alarm Contact Connection Explain 5 12 Figure 7 1 Control Panel for Heratherm IMH Series and IMH S Series Incubators eee 7 1 Figure 10 1 Door Seal Replica 10 4 Thermo Scientific Heratherm i List of Figures ii Heratherm Thermo Scientific CC 6i Safety Notes Basic Operating Precautions These operating instructions describe Heratherm incubators Heratherm incubators have been manufactured to the latest state of the art and have been tested thoroughly for flawless functioning prior to shipping However the incubator may present potential hazards particularly if it is operated by inadequately trained personnel or if it is not used in accordance with the intended purpose Therefore the following must be observed for the sake of accident prevention Herathe
53. f necessary If this does not solve the problem call ser vice sor Signal E108 of the A D converter out put for the sample sensor has changed over a spe cific time period Constant Sensor Sig None of the decimal places Control transferred to refer Call service nal E106 of the A D converter out ence sensor audible alarm put for the process sensor activated alarm relay ener has changed over a spe gized message shown on cific time period display If both sensors are defective all control circuits will be disabled Constant Reference None of the decimal places Control continues on pro Call service Sensor Signal E107 of the A D converter out cess sensor audible alarm put for the reference sen activated alarm relay ener sor has changed over a gized message shown on specific time period display If both sensors are defective all control circuits will be disabled Constant Sample Sen None of the decimal places Audible alarm activated Call service alarm relay energized message shown on dis play Heating Relay Error E109 The voltage measurement has indicated a defect in the heater circuit relay Device completely inopera tive audible alarm acti vated alarm relay energized message shown on display Be sure to pull the power plug and disconnect the device from the AC mains Call service Thermo Scientific Heratherm 12 3 Error Codes Table 12 1 Herath
54. following clearances should be kept Fig 3 A B C and D see Operating Instructions of the unit E mm inch F mm inch G mm inch H mm inch 100 4 50 2 80 3 2 30 1 2 Installation Built in Units IGS Clearances without exhaust hose IMH IMH S Clearances close air port with plug supplied with the unit OGS OMS Clearances with additional space to operate to air slide with air exhaust system and exhaust hose 40 mm 1 58 in 1 5 m 59 in original Thermo accessory shortened to required length OGH OGH S Clearances with air exhaust system and exhaust hose 40 mm 1 58 in 1 5 m OMH OMH S 59 in original Thermo accessory shortened to required length Operating temperature up to max 250 C 482 F After connecting the built in unit to the electrical N Q TE power supply avoid damaging the power cord then sliding into the installation position When installing the incubator make sure that the installation and supply connections remain freely accessible The specified side clearances represent minimum distances Thermo Scientific Heratherm 3 3 Installation Room Ventilation Table top incubators Figure 3 1 Table top incubators dimensions and required clearances Table 3 1 Incubator Dimensions Model A mm B mm C mm D mm IMH 60 530 20 1 565 22 2 720 28 3 540 21 3 IMH 100 640 25 2 565 22 2 820 32 3 650 25 6 IMH 180 640 25 2 738 29 1 920 36 2 650 25 6
55. ght of sample container The shelves 2 have an integrated tilt protection and pull out stop For details on using the shelf system see Installing the Shelf System on page 5 1 Thermo Scientific Heratherm 4 15 Product Description Work Space Components y 3 m o m pooooobDoDoDo ho C 1 Air Baffles 2 Retaining Springs only for table top incubators 3 Support Rails 4 Shelf Support 5 Shelves Figure 4 13 Shelf System 4 16 Heratherm Thermo Scientific Product Description Tube Access Ports Tube Access Ports Heratherm incubators may be equipped with additional tube access ports in the side and top panels Available tube access port options are listed in table 4 1 below Tabelle 4 1 Tube Access Ports for Heratherm Incubators Option Side Panel Mounted Port Top Panel Mounted Port Model dia in mm inch dia in mm inch IMH and IMH S 24 0 95 or 58 2 28 24 0 95 or 58 2 28 The tube access ports are mounted in fixed locations in the side and top panels see figure 4 14 E Figure 4 14 Tube Access Ports 1 Top panel mounted tube access port 2 Side panel mounted tube access port 3 Sealing cap for side panel mounted tube access port Once the cables tubes or other conduits have been inserted the tube access ports must be padded with the heat resistant fiber pads shipped with the device and the cap must be mounted to seal the port as far as possible W
56. gizing the AC outlet in the work space as well as a variety of other functions Under normal operating conditions the display presents user with the work space temperature The display returns to its default mode upon completion of the adjustments or whenever no entries have been made for a period of 30 seconds The graphic below shows the Heratherm IMH 60 100 180 and IMH 60 100 180 400 750 S control panel with all of its visualization elements and controls Figure 7 1 Control Panel for Heratherm IMH Series and IMH S Series Incubators n n E D1 UI s 7 D6 D3 K1 K4 a K5 The table below contains brief descriptions of the buttons on the control panel items K1 through K5 in figure 7 1 Thermo Scientific Heratherm 7 1 Handling and Control Table 7 1 Control Buttons Icon Item Function MEN K1 Menu Enter button First key press Activates the menu highlighting the first menu item with a red border see D3 Second key press Selects the currently activated menu item as highlighted by the red border Depending on the currently selected function pressing this button enables entries with item D2 D5 or D6 Third key press once a setting has been changed Confirms a previous entry or selection K2 Left button After the first press of the Menu Enter button Moves the selection in the menu see item D3 to the next icon on the left Once a menu item has been selected Decreases an adjustable paramet
57. herm incubators are not in a sterile state Before the initial start up the incubator must be decontaminated The following work space components should be checked for cleanliness and disinfected prior to use Support rails Shelf support Perforated shelves e Useable space surfaces Work space seals and gaskets Glass door 5 2 Heratherm Thermo Scientific Installation procedures Preparing the useable space N O TE Cleaning and disinfection For details about the cleaning and disinfection of the incubator please refer to Cleaning on page 9 1 Installation or Removal of the Support Rails 0 0 Figure 5 3 Support Rail Installation The embossings at 2 and 5 act as lateral guides for the support rails while the embossings at 1 and 6 secure the support rails in place For the support rails to install correctly the retaining spring 3 must be facing upwards 1 Place the support rail 4 on the lower embossing 6 and tilt it upwards against the work space side wall so that the rail is positioned over the two embossings at 5 and 2 2 Clamp the retaining spring 3 behind the upper embossing 1 3 To remove the support rails pull the retaining spring tab down out of the embossing and remove the support rail assembly Thermo Scientific Heratherm 5 3 Installation procedures Preparing the useable space Installing and Uninstalling the Air Baffle Heratherm IMH an
58. hrough overheating in case of contoller failure an overheat protection cut out feature that shuts down the incubators IMH S completely when excessive temperatures occur in the workspace an alarm relay that is energized along with audible and visual alarms to indicate errors encountered during operation dual fuses rated at 16 amperes Work Space Atmosphere To ensure undisturbed operation the ambient temperature in the operating room must be at least 18 C 64 4 F The heating system uses this temperature threshold to control the ambient temperature plus 5 C 41 F up to the maximum of 105 C 221 F Door Switch Heratherm IMH 60 100 180 400 750 S incubators come with a door switch 1 integrated into the latch mechanism If the door switch is activated by opening the door heating operations in the work space are suspended and an icon is illuminated in the display window see D4 in figure 7 1 on page 7 1 If the door remains open for more than 30 seconds a short audible alarm is sounded in addition to the icon in the display window If the door is left open for more than 10 minutes an audible alarm is sounded a door open E001 alarm message appears in the display and is issued through the RS 232 interface and the alarm relay is energized Thermo Scientific Heratherm 4 11 Product Description Sensing and Control System Sensing and Control System The PT 100 type sensor for the control of the w
59. iba 9 3 MM TD ad EN Y 9 4 Final EHSIHICCEIOB sus O setate e 9 4 Starting the Decontamination ROD rra qid oe rage redeo pod del atero Deed eius 9 4 Chapter 10 iore P 10 1 Inspectionsand CHECKS iresi t hu Io dab eso used teu aa 10 1 Regular Enea anillas dida dali 10 1 Set annual special teet erui 10 1 A AS 10 2 TAO CS AR cas 10 2 ASC o 10 2 Preparing Temperature Calibrador ghee des A nda 10 3 Comparison Measurement Proc iii ida si riadas 10 3 Temperature Calibration Procedure nadal didas te 10 4 Replacing the Door Selina A bed rici cto au DN du RAE Ub n 10 4 Replacing the Power Cordial talado ia adapta 10 5 Ret rns fot Re pala A A A A ad 10 5 Chapter TI DISPO al rs HL tm 11 1 Overview of Materials Used a A rc 11 1 Chapter 12 Error Codes 0 A Use uias epe cu ten ema deduc aaua kaa anaia 12 1 Chapter 13 Technical Data 13 1 Chapter 14 Spare Parts and Accessories ccssseeeceeeeeeeeeeseeeeeeeeseeeeeseseneeeeenseneeeeesseeeeeeseeeeeeenseees 14 1 Chapter 15 Device Log iuris edt brides chcavensmadtanteudsn d Lu aM URN dd 15 1 Chapter 15 Contact Er heh ead eect cade as ea t uiia qeu i mu eI cha 16 1 Thermo Scientific Heratherm iii Contents iv Heratherm Thermo Scientific ee List of Figures Figure 3 1 Tabletop incubators dimensions add required clearances iii ser cekttn tribes trn eia Hia ei
60. ions of the individual menu items are given in table 7 3 below Note Ifa menu item cannot be selected then the function it represents is not part of the equipment configuration of your unit D4 Status display area with three icons representing specific sta tuses of the incubator from left to right The Door Open icon appears when the front door of the incu bator is open or has not been closed correctly see Door Switch on page 4 11 Note The Door Open icon is only functional with IMH S Series devices Upon occurrence of an error condition the red alarm icon will be illuminated At the same time the current error code will flash in the display field at D2 The alarm may be acknowledged by pressing the co button The readiness indicator icon appears when the incubator has been switched off using the On Off button item K3 in figure 7 1 Settings pane labeled Set for temperature set value in either C or F depending on the user s preferences see Temperature Display Unit on page 7 27 At temperatures below 105 C or 221 F the temperature readout has one digit after the decimal point while temperatures beyond are shown without any deci mal places Thermo Scientific Heratherm 7 3 Handling and Control Table 7 2 Display Features Feature Item Function D6 The left one of the two vertical bar graphs belongs to the Fan icon directly beneath it and displays the current fa
61. lass door the interior panel of the outer door as well as the surfaces of the shelving and the work space become hot while the incubator is running through its heating cycles and need some time to cool down When removing samples from a running or recently completed heating cycle always wear safety gloves and other appropriate personal protection equipment to avoid burns on hot surfaces Risk of overloading Overloading may damage the shelves or cause the shelves and or the incubator to tilt when the shelves are being drawn out ultimately destroying the samples To avoid overloading the incubator or its shelving be sure to observe the sample weight limits specified in chapter 13 Technical Data NO TE Proper loading To ensure sufficient air circulation and uniform heating of the samples do not use more than 70 of the maximum surface area of the work space Bulky objects in the work space that dissipate heat may impair heat distribution 6 2 Heratherm Thermo Scientific A UN Handling and Control Heratherm IMH Series and IMH S Series incubators come with a front panel mounted control unit consisting of a multifunctional display four control buttons and an on off button The four control buttons interact with the display window to let users access all of the user control functions and adjustments of the incubator including for example the temperature set value timer energizing de ener
62. le 7 4 Adjusting the Temperature Set Value Press to activate the menu bar then use to select the Temperature icon and press to confirm In the flashing settings pane Set press or ESB to ed tO adjust a new temperature set value then press confirm your settings The display returns to its default mode The actual temperature measured in the work space and shown in the temperature display area starts to change until it reaches the newly adjusted set value Thermo Scientific Heratherm 7 7 Handling and Control Timer 7 8 Timer The Timer feature from the menu bar enables the user to turn the incubator on and off at scheduled times The timer supports three different modes of operation depending on the user s preferences Countdown type on or off timer Turns the incubator on or off after a user specified period of time Instructions on setting the preferences for this option are given in table 7 5 while its use as an off timer and on timer are described in table 7 6 on page 7 9 and table 7 7 on page 7 9 respectively Fixed time on or off timer Turns the incubator on or off at a scheduled time Instructions on setting the preferences for this option are given in table 7 8 on page 7 10 while its use as an off timer and on timer are described in table 7 9 on page 7 10 and table 7 10 on page 7 10 respectively Weekly timer Turns the incubator on or off at scheduled times on
63. le sensor connection IMH S only Heratherm 4 3 Product Description Heratherm IMH S Incubator Overview Heratherm IMH S Incubator Overview IMH S Series advanced protocol security microbiological mechanical convection incubators come equipped with the features also found in IMH Series devices including high precision work space temperature control adjustable in steps of one tenth of a degree up to 105 C 221 F a variable speed work space fan adjustable on the control panel at high ambient temperatures the maximum speed is reduced At high ambient temperatures the maximum speed is reduced countdown fixed time and weekly timers for timed process control two perforated shelves for sample containers an access port for tubing sensor leads etc Additionally IMH S Series incubators offer the following extra functionality 4 4 Heratherm Monitoring of lower temperature Connection for Acceptable temperature sensor accessory must be ordered separately a lockable door to secure a running process against unauthorized access a door switch and indicator on the control panel to indicate that the door is open a built in fully automatic decontamination routine Thermo Scientific Product Description Heratherm IMH S Incubator Overview The individual features of IMH S Series incubators are shown in the figures below Figure 4 3 Heratherm IMH 60 S IMH 100 S IMH 180 S Series Front View Outer doo
64. les sitaona a Erabebu isset abuelo tasa lacada 5 12 iiri mer ia 6 1 Pr paring thie Incubator oeste de do abel eios 6 1 Starting Operai Oni ER 6 1 Handling and Control cocina 7 1 Poweting lJ pusiste tette tein oi ende Hec D MERE 7 6 Switching the Incubator Off Powering Down siii a dla 7 6 Temperature Set V alieno diues ici tail ios 7 7 AE iso tee eder tenir e e eed eee io 7 8 Setting a Fused time Onor OTT EIE sacos edades e tun T basta e GbR dud Ua I Mead 7 10 Setting Weekly D 81 adc esa aa iN Dada eda eie idus 7 11 StOPping M Bird 7 13 Posyer Outdec rable topancubatorsoDbBo oa eao aivae obese see Qt ood eee tig egeat edad etas 7 15 D contaminati n it A ee teo alee ee ed AE ee d e siae eee Ee 7 16 do ide 7 19 Table top Inc bators dai O da o dude AS Ad 7 19 ii Heratherm Thermo Scientific Contents Floor stand incubators a E NEESI OSEKE ae ica 7 20 Nunc 7 22 TPO ROG NN NN 7 22 CADA A AS AAA ANN i 7 23 DS Naci 7 24 Temperature Display UE aaa 7 27 Chapter 8 Sh t dOWLi a nii nnmnnn annnm IR tei eet amine 8 1 Shutting the Incubator Doc doi aria 8 1 Chapter 9 Cleaning and Disinfection eeeeeeeeeeeeeeeeeeeeeeeee eene nennen nennen nenne nnne nnns nnn 9 1 Cleaning o5 nsn AI NS d Mod EAS 9 1 Cleaning Exterior Surfaces ta 9 1 Viper Spray DUISIBfec Habbo id id 9 1 Preparing the Manual Wipe Spray Disinfection iii 9 2 isdisinfectUl ini dinastia iio aida anda iio
65. ly using a solution of lukewarm water and commercial detergent Wipe the surfaces clean using a clean cloth and clear water Then wipe the surfaces dry using a clean cloth Wipe Spray Disinfection The manual wipe and spray disinfection is a three stage process predisinfection cleaning final disinfection Thermo Scientific Heratherm 9 1 Cleaning and Disinfection Wipe Spray Disinfection NCAUTION Alcoholic disinfectants Disinfectants having an alcohol content of more than 1096 may form in combination with air easily combustible and explosive gas mixtures When using such disinfectants avoid open flames or exposure to excessive heat during the entire disinfection process Use such disinfectants only in adequately ventilated rooms After the disinfectant has been allowed to react wipe the cleaned incubator components thoroughly dry Observe safety regulations to avoid fire and or explosion hazard caused by alcohol containing disinfectants NCAUTION Chloride containing disinfectants Chloride containing disinfectants can corrode stainless steel Use only disinfectants that do not affect stainless steel Preparing the Manual Wipe Spray Disinfection The surfaces of the work space may be contaminated Contact with contaminated cleaning liquids may cause infections Disinfectants may contain harmful substances When cleaning and disinfecting always observe the safety IN
66. m the work space Perform the check as requested close the door and finally launch decontamination 7 16 Heratherm Thermo Scientific Handling and Control Decontamination Table 7 18 Launching Decontamination 2010 03 31 1 34PM Decontamination 12 15 A progress bar and a residual time readout for the decontamination process appear in the multifunctional display pane Opening the door while decontamination is running Opening the front door during the heating and holding phases causes the decontamination routine to stop and wait for the door to be closed At the same time the Door Open icon middle item of the group D4 on page 7 1 is lit in the display window As soon as the door is closed decontamination starts over cycling through the entire process from the start This may extend the overall duration of the decontamination effort substantially Power Outage during a Decontamination Run A power outage relaunches the decontamination routine automatically The Alarm icon leftmost item of the group D4 on page 7 1 is illuminated in the display window and a E007 Power Down Error message appears at the end of the process Press the button to acknowledge that alarm Put up bio hazard warning signs Under specific circumstances there is a risk that bacteria viruses fungi prions and other biological substances survive when the decontamination routine is aborted due to a power outage Norm
67. mal container Do not use a container filled with water as an isothermal container because the evaporation of water will result in a lower temperature reading Excessive work space temperatures Excessive work space temperatures after the calibration may be reduced by leaving the doors open for approx 30 seconds Comparison Measurement Procedure 1 Turn the incubator on using the power switch 2 Set the temperature set value and allow the incubator to stabilize This may take several hours 3 Place the measuring device in the center area of the work space Alternatively a temperature sensor may be positioned in this location Route the connecting cable between the glass panel and the interior tank 4 Close the doors 5 Wait until the temperature value displayed on the measuring instrument has stabilized 6 Use the temperature reading from the measuring device to calibrate temperature control manually as explained Entering the Calibration Reference Temperature Manually on page 7 23 Thermo Scientific Heratherm 10 3 Maintenance Temperature Calibration Procedure Temperature Calibration Procedure For detailed instructions on how to perform a manual temperature calibration please refer to the instructions in the section Calibration on page 7 23 N O TE Excessive work space temperature Excessive work space temperatures after the calibration can be reduced by leaving the doors open for app
68. n speed level Fan speed level for table top incubators Bar graph for fan speed setting in 6 steps O 5 0 no chevron illuminated 2096 chevron 1 illuminated 4096 chevrons 1 and 2 illuminated 6096 chevrons 1 through 3 illuminated 8096 chevrons 1 through 4 illuminated 10096 chevrons 1 through 5 illuminated Fan speed level for floor stand incubators Bar graph for fan speed setting in 2 steps Minimum fan speed level chevrons 1 through 3 illuminated Maximum fan speed level chevrons 1 through 5 illuminated Lh XV The table below contains brief descriptions of the menu bar icons item D3 in figure 7 1 Table 7 3 Menu Bar Icons Icon Function Temperature Set Value Allows for changing the temperature set value factory preset to 37 C 99 F within the permissible temperature range The set value can be changed by pressing the Left and Right item K2 or K4 and you can after confirming your changes with the Menu Enter button item K1 track the impact on the actual temperature in the temperature display field at D1 Instructions Temperature Set Value on page 7 7 Timer Allows for having the incubator turn on or off upon expiry of a user speci fied countdown period or at a fixed on or off time or having it operate on a complete weekly schedule of daily on and off times When the user enables an on timer the display goes out A rotating hand in the Timer icon
69. o be ordered separately Contaminants such as bacteria viruses fungi prions and other biological substances may use the open door to migrate easily from the floor into the incubator s work space Intermediate Storage When the incubator is placed in intermediate storage which is permissible for a maximum of four weeks make sure that the ambient temperature is between 20 C to 60 C 68 F to 140 F and the maximum relative humidity does not exceed 90 non condensing Room Ventilation Heat dissipating from the incubator during continuous operation may cause a change in the room climate 3 2 Heratherm Therefore the incubator must only be installed in rooms with sufficient ventilation Do not install the incubator in room recesses without ventilation When several devices are to be placed in the same room additional ventilation may have to be provided as necessary To avoid any impact of the heat dissipated by the incubator on the ambient climate the room must be vented by means of a laboratory grade ventilation system that complies with applicable local and national health and safety regulations and has sufficient capacity If excessive temperatures tend to occur in the operating room be sure to provide a thermal protection means that cuts out the power supply to mitigate the impact of overtemperature scenarios Thermo Scientific Installation Room Ventilation Space Requirement For built in units
70. o change without notice All technical information in this document is for reference purposes only System configurations and specifications in this document supersede all previous information received by the purchaser Thermo Fisher Scientific Inc makes no representations that this document is complete accurate or error free and assumes no responsibility and will not be liable for any errors omissions damage or loss that might result from any use of this document even if the information in the document is followed properly This document is not part of any sales contract between Thermo Fisher Scientific Inc and a purchaser This document shall in no way govern or modify any Terms and Conditions of Sale which Terms and Conditions of Sale shall govern all conflicting information between the two documents i ii Heratherm Thermo Scientific Oo M Contents Chapter 1 Safety 1 1 Basic Operating AAA AT 1 1 Op r tional Safety Bole ara ta 1 2 NE A O RN 1 2 Explanation of Safety Information and Souiboleus aieo tilda 1 3 Safety Notes and Symbols Used Throughout These Operating Instructions eee 1 3 Additional Symbols for Safety Information ici 1 4 Symbols on the Inc bator ciet e ie OR RETE ERE E PEE RR notado alain 1 5 Intended Purpose of the Encub atatueiocestesei respicit i eiui ia iia 1 6 Intended Purpose obs Incubator nai deere iniaua ne esi baise esi o
71. of the incubator and its components Prior to return shipment it is therefore mandatory that all incubator components be properly decontaminated Clean the incubator components thoroughly then disinfect or decontaminate them depending on application Fill in and attach a safety declaration with details on decontamination activities performed to the items that are to be repaired Thermo Scientific Heratherm 10 5 Maintenance Returns for Repair 10 6 Heratherm Thermo Scientific LL mm Disposal ZA WARNING Contamination hazard The incubator may have been used for treating and processing infectious substances which may have caused contamination of the disposed of incubator and its components Prior to disposal it is therefore mandatory that all incubator components be properly decontaminated Clean the incubator components thoroughly then disinfect or decontaminate them depending on application Attach a declaration of decontamination with details on decontamination activities performed to the items that are to be Overview of Materials Used Component Thermal insulation components Material Glass wool Printed circuit boards Coated electrical components contain various plastics materials Components mounted on circuit boards containing epoxy resin bonder Plastic components general see material labelling Exterior housing Galvanized s
72. ont Pull out Stop Shelf Figure 5 9 Perforated Shelf 1 Push the shelf 4 onto the shelf support brackets with the tilt protection devices 2 facing the rear panel of the incubator 2 Slightly raise the perforated shelf so that the pull out stops 1 and 3 can slide over the shelf support brackets 3 Make sure that the shelves and both of their tilt protection devices are free to move over the shelf support brackets Mains connection Contact with live electrical components may cause a lethal electric shock Before connecting the incubator to the power supply check the power cord and the plug for damage Do not use damaged cables for connecting the incubator to the power supply The incubator has a class I protection earthed enclosure To minimize the risk of electrical shock use the AC power cord supplied to connect the incubator to a correctly installed and protection earthed power supply source with the following features in place for each incubator T 16 A slow blow fusing e B 16 circuit breaker Thermo Scientific Heratherm 5 7 Installation procedures Mains connection Connecting to the Power Supply Source 1 Before connecting the incubator to the power source check to see if the power supply voltage corresponds with the specifications on the nameplate on the front of the incubator If the voltage V and current A ratings given are not as required do not connect the incubator to th
73. ope Austria Sales 43 1 801 400 Service 43 1 801 400 Belgium Sales 32 53 73 4241 Service 32 53 73 4241 Finland Nordic Baltic countries Sales 4358 9 329 100 Service 358 9 329 100 France Sales 433 2 2803 2180 Service 33 825 800 119 Germany Postal Address Germany Thermo Electron LED GmbH Robert Bosch Strafse 1 D 63505 Langenselbold Phone Sales Toll free 0800 1 536 376 or 49 6184 90 6940 Service Toll free 0800 1 112110 or 49 6184 90 6940 E Mail info labequipment de thermofisher com Italy Sales 39 02 95059 341 Service 39 02 95059 250 Netherlands Sales 31 76 579 5555 Service 31 76 579 5639 Russia CIS Sales 7 812 703 4215 Service 7 812 703 4215 Spain Portugal Sales 34 93 223 0918 Service 34 93 223 0918 Switzerland 41 44 454 1212 Service 41 44 454 1212 UK Ireland Service 44 870 609 9203 Sales 44 870 609 9203 Heratherm Thermo Scientific Contact Thermo Scientific Heratherm 16 3 Part of Thermo Fisher Scientific SCIENTIFIC
74. ork space temperature and for the thermal protection 1 is installed on the bottom of table top incubators and in the top of floor stand incubators Figure 4 9 Sensor System for table top incubators Figure 4 10 Sensor System for floor stand incubators The work space temperature sensor provides the inputs to the incubator s built in controller which continuously compares the measured values to the user specified set value and adjusts the heaters according to the result Do not remove the protection hose from the sensor Protect the sensor from mechanical damage The unit features a thermal protection function that is factory preprogrammed and not adjustable It protects the cultures in the work space from overheating Thermal protection kicks in on a brief violation of the upper limit based on the defined setpoint temperature at between 2 and 3 C 35 6 F and 37 4 F 37 C 99 F 2 C 35 6 F gt 50 C 122 F 3 C 37 4 F automatically reducing the work space temperature to the user specified set value and allowing the incubation process to be continued even in case of a controller malfunction If the thermal protection is activated the error message E111 Temperature too high appears in the display window and an audible alarm is sounded When the user acknowledges the error message the red alarm icon D4 in figure 7 1 on page 7 1 is illuminated and the Temperature Set Valu
75. ors 50127469 Door switch for the right side of Heratherm incubators and heating amp drying ovens 50127470 Door switch for the left side of Heratherm incubators and heating amp drying oven 50127472 Kit glass door IGS 60 IMH 60 IMH 60 S 50127473 Kit glass door IGS 100 IMH 100 IMH 100 S 50127474 Kit glass door IGS 180 IMH 180 IMH 180 S 50127478 Temperatur limiter for IMH S 50127480 Door hook catch for Heratherm incubators and heating amp drying ovens with a door stop on the right side 50127481 Door hook catch for Heratherm incubators and heating amp drying ovens with a door stop on the left side 50127482 Magnetic door hook catch for Heratherm incubators and heating amp drying ovens with a door stop on the right side 50127483 Magnetic door hook catch for Heratherm incubators and heating amp drying ovens with a door stop on the left sid 50127497 Heating coils for Heratherm IMH S at a voltage of 120 V 50127498 Heating coils for Heratherm IMH S at a voltage of 230 V 50127504 Kit Heating coils IMH 120 V 50127511 Kit fan system Heratherm IMH 60 IMH 60 S OMH 60 and OMH 60 S IMH 100 IMH 100 S IMH 180 and OMH 180 S 120 V 50127515 Kit Heating coils IMH 230 V 50127531 Circulation fan IMH IMH S D 160 mm 6 3 inch H 28 mm 1 1 inch Heratherm Thermo Scientific Material No 50127555 Spare Parts and Accessories Description Kit fan system Heratherm IMH 60 IMH 60 S OMH 60 and OMH 60 S IMH 100 IMH 100 S IMH 1
76. peed will be restored 7 18 Heratherm Thermo Scientific Handling and Control Fan ES Fan XN This menu item allows for turning on the fan inside the work space and gradually adjusting its speed in one go The current setting of the fan is indicated by the illuminated Fan icon in the menu bar and the five level bar graph see item D6 in figure 7 1 on page 7 1 for the fan speed setting located directly above the icon Table top incubators The fan can be adjusted in 6 levels 0 all chevrons extinguished e 20 1 chevron illuminated e 40 2 chevrons illuminated 60 3 chevrons illuminated e 80 4 chevrons illuminated 10096 5 chevrons illuminated Table 7 20 Turning on the Fan f Press to activate the menu bar then use or N to select the Fan icon and press to confirm The settings dialog shown at left appears in the multifunctional display pane now with the value 0 flashing already 31 03 2010 14 15 0 gt 31 03 2010 14 15 Press as often as needed to reach the desired fan AES D speed level then confirm with ES The multifunctional display pane will show the current fan speed level as a percentage 20 40 60 80 ORGANE TO or 100 Additionally the matching number of NA chevrons will be illuminated in the bar graph to the right The display returns to its default mode N The Fan icon in the menu bar is illuminated now to indicate that the fan is
77. r Door switch Door latch and handle with lock Door hinge lower Levelling foot Nameplate Temperature sensor Support rail for perforated shelf Shelf support Fan opening air baffle Door hook catch Air baffle Door seal Stacking pad Spring Access port e a Aa Aa A o pl el 1D 00 AN KRW ND na XO 00 ON VA 4X Q2 NO e OSV CS CS CC I a o a re cc SS eS NO e A aaa Glass door Thermo Scientific Heratherm 4 5 Product Description Heratherm IMH S Incubator Overview Figure 4 4 Heratherm IMH 60 S IMH 100 S IMH 180 S Series Rear View 1 Door latch and handle 2 Control panel 3 Stacking pad 4 Access port 5 Fan 6 Electronics compartment 7 Levelling foot 8 Sample Sensor connection 4 6 Heratherm Thermo Scientific Figure 4 5 Heratherm IMH 400 S Series Front View NN Rm Ln Ln n Al A 21000 OV KWH c4 QC XO 00 1 ON VA 4X Q2 NO eo OSS CS CS CO a nM a ee oc cocco ee L C C Cc ccc a O a Thermo Scientific Outer door Door latch Unit caster Air baffle Perforated shelf Door hook catch Glass door latch Temperature sensor Access port Glass door Fan opening air baffle Product Description Heratherm IMH S Incubator Overview Heratherm 4 7 Product Description Heratherm IMH S Incubator Overview 4 8 Figure 4 6 Heratherm IMH 400 S Rear View RO C XO Oo 1 ON VA dx Q2 NO A ooo CCS L c VC CX CV O Li A Heratherm Outer door Unit caster
78. r 4 screws in the bottom plate and then remove the bottom plate completely 28828885 4 a 4 4 2ocoocoo H 4 i 4 4 3 k poco Coooooo L a k s x E E K K N 3 y Figure 5 6 Removing the left and right support profiles Loosen and remove the eight 8 screws for the left and right support profiles and then take out the lateral air baffles Thermo Scientific Heratherm 5 5 Installation procedures Commissioning general o Js D a m m i a ii E 2 o B a T a Im QU B o s B m B i E 8 la 5 ae o CI qi s En a Do o a a o a o o o B c oo 8B Figure 5 7 Removing the rear air baffle IMH 400 S 750 S On the IMH S 400 model loosen and remove the six 6 screws for the rear air baffle and for model IMH S 750 loosen and remove the six 6 screws for the top and bottom air baffles and then remove the air baffle s Commissioning general Installing the Shelf Support Brackets 1 Insert the shelf support bracket 3 into the perforations 1 of the support rail and tilt it downwards 2 Make sure that the two vertical elements 2 of the shelf support bracket butt against the support rail Figure 5 8 Shelf Support Bracket Installation 5 6 Heratherm Thermo Scientific Installation procedures Mains connection Installing the Perforated Shelves Rear Pull out Stop Tilt Protection Device Fr
79. r and drop down when being transported in a stack To avoid injury to persons and damage to equipment do not attempt to move stacked devices as a unit Separate and move each device one by one then restack them 3 12 Heratherm Thermo Scientific Installation Floor stand unit spacers Floor stand unit spacers The spacer on the electrical module must be pulled out and fixed in place before installing the floor stand unit at its installation location UA 1 Loosen the 2 screws 2 Pull out the spacer and slide the screws into the recesses 3 Tighten the two screws Thermo Scientific Heratherm 3 13 Installation Floor stand unit spacers 3 14 Heratherm Thermo Scientific A a Product Description This section describes Heratherm advanced protocol microbiological incubators for high end laboratory applications which are available in two different versions distinguished by safety level Heratherm IMH Series advanced protocol microbiological fan convection incubators see Heratherm IMH Series Incubator Overview on page 4 1 Heratherm IMH S Series advanced protocol security microbiological fan convection incubator for more exacting safety level requirements see Heratherm IMH S Incubator Overview on page 4 4 Heratherm IMH Series Incubator Overview IMH Series advanced protocol microbiological incubators come equipped with the following features high precision work space temperature control adjustable in steps
80. r second Thermo Scientific Heratherm 5 9 Installation procedures Connecting the RS 232 Interface 8 data bits 1 stop bit No Parity 7 Once your terminal indicates that serial communication has been established successfully enter any of the commands listed in table 5 1 below depending on what type of information you want to query 8 Use the following generic command syntax aaaa bb cc lt CR gt Where identifies the command line as a query aaaa is the parameter address bb is a query that must be left at 00 for technical reasons cc is for a command specific checksum listed in the table below lt CR gt is for carriage return You will receive a response of the following general format laaaa bb XXXXX cc CR where k identifies the line as a response to a query aaaa is the parameter address entered with the query bb is the number of payload bytes in hexadecimal code for example 1F for the decimal value 31 s XXXXXX is the significant status information queried cc is a check sum technically an inverted XOR of all bytes returned excluding the check sum bytes and the CR character lt CR gt is for carriage return Table 5 1 Terminal Commands for Querying Data Command Syntax Combined Date and Time Response Example 0010 00 c1 1 0010 11 31 07 10 01 02 23 e2 Date Time Date only 2 00
81. re disabled by default If there is no need to set the turn on and or turn off times for a specific weekday press 89 and om to go back and forth to the previous and next day respectively RA When prompted to save your changes press E to vdd confirm 4d4No Yesp Note This prompt for saving also appears when you press the Esc button while working on the weekly timer s settings ARESE PAT To enable the weekly timer press C3 Timer 4 On Alternatively press and to select the Off option if the weekly timer you have just saved should be activated at a later date In the menu bar the Timer icon is illuminated and a hand is rotating on the icon s face 7 12 Heratherm Thermo Scientific Stopping a Timer Handling and Control Timer Table 7 13 Stopping an Off Timer Before It Expires Press to activate the menu bar then use 122 to select the Timer icon and press to confirm 2010 03 29 1 12Pm Stop Timer q No Yes gt Press to confirm the Yes default selection 2010 03 29 4 05Pw Timer stopped The message Timer stopped appears as a confirmation The display will return to the main menu In the menu bar the Timer icon will go out Table 7 14 Stopping an On Timer Before it Expires To cancel a pre programmed on timer while the incubator is switched off hold the On Off button depressed for a few seconds 2010 03 29 1 12Pm Stop Timer 4 No Yes gt In the Stop Timer prompt
82. requires a standard RS 232 cable with 9 pin connectors and a straight 1 1 pinout without any crossed wires which is not supplied with the incubator Users may employ the RS 232 command inventory listed in table 5 1 below for automating process data logging for example by embedding these commands in scripts that run on a remote computer NCAUTION RS 232 interface compatibility To avoid overloading and damaging the RS 232 interface check the interfacing parameters against the pin out description given above and make sure that computer s interface port works with a signal level of 5V DC Interconnecting the Incubator with a Computer 1 Turn the computer off 2 Route the serial interface cable along a path that does not cross hot exhaust air piping tables aisles or passageways With stacked devices keep the serial interface cable away from hot spots on the other incubator in the stack 3 Connect one connector of the serial interface cable cable length 5 to max 10 m not supplied as a standard item to the socket labeled RS 223 in the computer and alarm interface section at the rear of the incubator see Signal Interfaces and Power Socket on page 4 13 4 Connect the second connector to an unused COM 1 COM 2 or other serial port on the computer 5 Boot the computer 6 Launch our standard terminal rogram and set u the connection with the followin y prog p 8 parameters 57600 bits pe
83. rm incubators must be operated by adequately trained and authorized professional personnel Heratherm incubators must not be operated unless these operating instructions have been fully read and understood The present operating instructions applicable safety data sheets plant hygiene guidelines and the corresponding technical rules issued by the operator shall be used to create written procedures targeted at personnel working with the subject matter device detailing the decontamination measures to be employed for the incubator and the accessories used with it the safety precautions to be taken when processing specific agents the measures to be taken in case of accidents Repair work on the incubator must be carried out only by trained and authorized expert personnel The contents of these operating instructions are subject to change at any time without further notice Concerning translations into foreign languages the German version of these operating instructions is binding Keep these operating instructions close to the incubator so that safety instructions and important information are always accessible Should you encounter problems that are not detailed adequately in these operating instructions please contact Thermo Electron LED GmbH immediately for your own safety Thermo Scientific Heratherm 1 1 Safety Notes Operational Safety Rules Operational Safety Rules The following rules must be hee
84. rox 30 seconds Replacing the Door Seal The door seal of the outer door is located in the retaining slot The door seal should be inspected for any signs of embrittlement at half yearly intervals No tools are required to replace the seal Figure 10 1 Door Seal Replacement 1 Pull the seal out of the guide slot 2 Starting on the hinge side of the door position the end of the new seal at the location indicated by the arrow in figure 10 1 above 3 Gently press the seal into the slot working around the circumference of the door In corner areas in particular ensure that the seal lip is installed without any wrinkles and that the seal is not stretched or compressed 4 Make sure that the seal is positioned correctly in the slot and flush with the door frame Correct if necessary 10 4 Heratherm Thermo Scientific Maintenance Replacing the Power Cord Replacing the Power Cord If the power cord is damaged it must be replaced by an original spare part Using a standard power cord with a lower thermal withstand capabilities is prohibited Returns for Repair Prior to returning any materials please contact our Customer Service Department for a Return Materials Authorization number RMA Material returned without an RMA number will be refused A WARNING Contamination hazard The incubator may have been used for treating and processing infectious substances which may have caused contamination
85. rror E002 Display communication error The built in control ler was unable to restore communication with the control panel Audible alarm activated alarm relay energized message shown on dis play Reset after 30 s Power cycle the device by unplugging then recon necting the power cord If this doesn t solve the prob lem call service Mirrored Parameter Loaded E003 The controller was unable to read the user specific settings and had to resort to an emergency parame ter set held in mirrored stor age Alarm relay energized Fall back to mirrored parame ter storage Device continues to run without loss of functionality includ ing user specific settings Check the latest settings for example the set value Factory Parameter Loaded E004 The controller was unable to read the mirrored param eter set and had to resort to factory preset parameters Fallback to factory preset parameters Audible alarm activated alarm relay ener gized message shown on display User specific set tings may be lost for example the temperature display unit preference or user programs Acknowledge by pressing Co Re enter cus tomer specific settings Default Parameter Loaded E005 The controller was unable to read the factory preset parameters and had to resort to default settings Fallback to default parame ters Audible alarm acti vated alarm relay energized message shown on
86. rs Rr UP C SRI 1 6 Incorrect Ur oia das 1 6 Standardsand DM VES iria AA DA 1 6 Chapter 2 Delivery of the IncUbalor ec eorr rane enint un ite ranas nume ta nans am suat e Ee nia 2 1 A O UN 2 1 Acceptance Inspection uie NN 2 1 o A iaEoE 2 2 Chapters Installation 3 1 Pl ERO MIND O AR OE OEE 3 1 Wore is oW nU 3 1 Intermediate PUEDE Boca dapi od RUD MA rud Eas pu VOU A t e e rue 3 2 ROSY en EH OH a AAA AA 3 2 NAAA TA 3 3 Installation Built in Di A 3 3 RC On Incubators ri A AEEA ETA a 3 4 Flo t Stand TS ida D T 3 5 MS NN 3 7 A A 3 9 Installing the Stacking Pra 3 9 Pura dris joo rior PTT 3 10 Installing the Anti tilt ADE as 3 11 Floor stand nit spacers essiri enese AA A DU URNA A AA 3 13 Chapter 4 Product Description lt iccoisamisianio nnne nan tnn cns ua ta caesa pna Ra Man cca nd MEER n ERR Rn P rR RR RUSSES 4 1 Heratherm IMH Series Incubator Overview augue ipe pa nias A AER VAL NU EA RE 4 1 Heratherm IMH S Incubator Overview ducsrassevi esee pore ee 4 4 Safety D ar MPH 4 11 Work Space Atmosphere MT TT 4 11 Door Switch MDC aiei en heat ENa ERE PTT 4 11 Sensing and Control Syste A UA EN EE RN asians 4 12 Thermo Scientific Heratherm i Contents Chapter 5 Chapter 6 Chapter 7 Data Communications amp Alarm Intetf36e o pri ds UI ERR 4 13 AA A A 4 13 Alarm Cont
87. running Thermo Scientific Heratherm 7 19 Handling and Control Floor stand incubators Table 7 21 Adjusting Fan Speed or Turning the Fan Off a Press to activate the menu bar then use or VN to select the Fan icon and press to confirm The settings dialog shown at left appears in the multifunctional display pane now with the current fan speed setting flashing already 31 03 2010 14 15 4 20 gt 31 03 2010 Change the fan speed with or C then press rq to confirm 31 03 2010 To turn off the fan use to reset its speed to 0 4 0 El E then press to confirm The display returns to its default mode If you have just changed the fan speed level the Fan will remain illuminated in the menu bar If you choose to turn off the fan altogether the Fan icon in the menu bar will be extinguished Floor stand incubators The unit contains a regulated fan fan speed can be lowered adjusted in 2 stages Minimum fan speed level chevrons 1 through 3 illuminated Maximum fan speed level chevrons 1 through 5 illuminated Table 7 22 Turning on the Fan LY Press to activate the menu bar then use 4 or XA to select the Fan icon and press to confirm The settings dialog shown at left appears in the multifunctional display pane now with the value 096 A flashing already 03 04 2012 12 46 4 60 gt Y 7 20 Heratherm Thermo Scientific
88. s Symbols on the Incubator Observe operating instructions Re Mark of conformity USA Canada C US 120 Volts AC power socket Alarm contact Thermo Scientific Heratherm 1 5 Safety Notes Intended Purpose of the Incubator Intended Purpose of the Incubator Intended Purpose of the Incubator Heratherm incubators are laboratory devices for preparing and cultivating cell and tissue cultures The devices employ precision temperature control for simulating the specific physiological ambient conditions for these cultures Incorrect Use To avoid the risk of explosion do not load the incubator with tissue material or liquids that are easily flammable or explosive release vapor or dust that forms combustible or explosive mixtures when exposed to air release poisons do not pour any liquids on the bottom of the interior surface or into a collecting basin inside the unit release dust exhibit exothermic reactions are pyrotechnical substances refrain also from pouring any liquids onto the internal base plate or inserting bowls filled with liquids into the sample compartment Standards and Directives The incubator complies with the following standards and guidelines IEC EN 61010 1 IEC EN 61010 2 010 Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC Additionally the incubator is in compliance with many other international standards regulations and directives not listed here Should you h
89. s or damage to the incubator and other equipment Service Intervals During running operation the following service works must be performed 3 monthly service Perform the comparative temperature measurement outlined in the following section Annual Service Have the incubator inspected and services by a Thermo Scientific authorized Technical Service agent N O TE Service contract comprising all necessary tests and service work Thermo Electron LED GmbH offer a product specific service contract 10 2 Heratherm Thermo Scientific Maintenance Preparing Temperature Calibration Preparing Temperature Calibration To determine the exact measured value of the incubator s integral temperature sensor a temperature comparison measurement must be performed every three months If a major temperature deviation is found during this check temperature calibration is required During this process the temperature controller of the incubator is set to the value measured during the temperature comparison measurement Use a calibrated measuring instrument with an accuracy of lt 0 1 C 0 18 F for this test To minimize temperature variations during the measurement put the measuring sensor in an isothermal container such as a bowl filled with glycerol before placing it in the work space Use the center of the work space as the reference location for the comparison measurement Isother
90. same type of enclosure yet with a different footprint the device with the smaller footprint must be placed on top of the one with the larger footprint at all times The bottom device must be correctly levelled Place the corresponding stacking adapter The levelling feet on the top device must be screwed in all the way Thelevelling feet of the top device must be aligned with and placed exactly on the stacking pads of the stacking adapter Theanti tilt anchor must be installed at the top device 3 10 Heratherm Thermo Scientific Installation Installing the Anti tilt Anchor Installing the Anti tilt Anchor Table top incubators The anti tilt anchor secures the top device in a stack to a solid part of a building The anti tilt anchor is to be mounted on the side opposite of the door hinges Bend the fixing tabs of the anti tilt anchor up on one side and down on the other by an angle of approx 90 1 Do not use this position if the door is hinged on this side Right hand hinges represent the standard configuration 2 Preferred position 3 Alternative position Do not use if the door is hinged on this side Remove the bracket screws Use the preferred position if possible Fix the anti tilt anchor with the bracket side down to the unit Position the unit with the anti tilt anchor to in an angle of approx 90 20 Take care that the stacking feet of the unit are still in correct place on the lower unit or on th
91. screen that appears press A or to switch to the On option and confirm the selected On option by pressing c3 2010 03 31 1 34pm The selected option On remains in the display pane for a few seconds to let you track your action The display returns to its default mode The AC Outlet icon in the menu bar is illuminated to indicate that the outlet is live Table 7 17 Turning the AC outlet off Press to activate the menu bar then use 122 to select the Power Outlet icon and press to confirm 2010 03 31 31 34PM On Off gt In the selection screen that appears press A or to switch to the OFF option and confirm the selected Off option by pressing E 2010 03 31 1 35pm Off The selected option Off remains in the display pane for a few seconds to let you track your action The display returns to its default mode The AC Outlet icon in the menu bar is extinguished to indicate that the outlet is switched off Thermo Scientific Heratherm 7 15 Handling and Control Decontamination Decontamination This menu item available on IMH S Series devices only launches the built in decontamination routine of the incubator The decontamination routine consists of a factory preprogrammed multi phase workflow heating holding cooling It works with a temperature set value of 140 C 284 F which is held over a period of six hours The overall duration of the
92. sly made settings The table below contains brief descriptions of the display features of the control panel items D1 through D6 in figure 7 1 the identifiers K1 through K4 refer to the buttons shown in that figure 7 2 Heratherm Thermo Scientific Handling and Control Table 7 2 Display Features Feature Item Function D1 Display field showing a permanent readout of the actual temper ature in the work space either in C or F depending on the user s preferences see Temperature Display Unit on page 7 27 At temperatures below 105 C or 221 F the temper ature readout has one digit after the decimal point while temper atures beyond are shown without any decimal places Alternatively a flashing time entry prompt of the general format hh mm hours minutes both with two digits appears in this place while the user is setting the incubator s built in clock 29 03 2010 12 59 heating relay D2 Four line multifunctional display pane with fields for date and time a display area for the specific options of the selected menu item alarm codes progress indicators for continuous processes for example program controlled temperature ramping etc D3 Menu bar with iconized representations of adjustable parame ters A red border is used to highlight the current menu item as selected using the Menu K1 and arrow buttons Left K2 and Right K4 Brief descript
93. ss to go to the next entry or to go back to the previous one After the entry numbered 21 the display wraps and returns to the beginning of the error log displaying Error 0 again To exit from the error log and return to normal display mode press twice The Settings icon in the menu bar will go out Calibration The Settings gt Calibration menu item enables the user to initiate a temperature calibration process see Temperature Calibration Procedure on page 10 4 for the built in temperature sensors and choose whether calibration should be accomplished manually or automatically The Manual option allows for entering an absolute temperature directly as measured for example using an external reference sensor N O TE Calibration Prerequisites Maintain the ambient conditions within the specified limits of the incubator before launching calibration Varying ambient conditions may impact the result of the calibration routine which may lead to misadjustment of the controller and unreliable temperature control operation Table 7 25 Entering the Calibration Reference Temperature Manually Prepare for temperature calibration see Preparing Tem perature Calibration and Comparison Measurement Pro cedure on page 10 3 Press to activate the menu bar then use or to select the Settings icon and press to confirm 2010 04 06 1 33PM 4 Error gt
94. t In the display window on the front panel the readiness indicator icon rightmost icon in the status display area at D4 in figure 7 1 on page 7 1 is illuminated Keep the On Off button depressed for two seconds An initialization routine will be run after the incubator has been powered up On completion of the initialization the display will light up and the current work space temperature will appear in the temperature display field item D1 in figure 7 1 on page 7 1 The incubator is ready for use now Switching the Incubator Off Powering Down 1 Keep the On Off button depressed for two seconds 7 6 The display window goes out except for the readiness indicator icon rightmost icon in the status display area at D4 in figure 7 1 on page 7 1 and a residual heat temperature readout in case the work space temperature is still higher than 50 C 122 F The incubator is switched off now 2 If required unplug the AC power plug to power down the incubator completely Heratherm Thermo Scientific Handling and Control Temperature Set Value n Temperature Set Value Heratherm incubators allow for setting the desired work space temperature directly using only a few button presses After confirming the new temperature set value in the settings pane Set item D5 in figure 7 1 on page 7 1 the user may trace the resulting temperature change in the temperature display field item D1 in figure 7 1 on page 7 1 Tab
95. t the hours and minutes until the incubator is supposed to shut down by pressing r then press to confirm The display returns to its default mode In the menu bar the Timer icon is illuminated and a hand is rotating on the icon s face Table 7 7 Setting a Countdown type On Timer Press to activate the menu bar then use to select the Timer icon and press to confirm 2010 03 29 12 59Pm 4On Off Press to select the on timer option On then to confirm 2010 03 29 1 05pm On Timer 00 00 Set the hours and minutes until the incubator is supposed to turn on by pressing oc then press to confirm The incubator switches off The display goes out the Timer icon is illuminated in the menu bar with a rotating hand on its face Additionally the readiness indicator icon is illuminated Thermo Scientific Heratherm 7 9 Handling and Control Timer Setting a Fixed time On or Off Timer Table 7 8 Presetting the Fixed time Timer Mode of Operation Press to activate the menu bar then use QA to select the Settings icon and press to confirm Press to switch to the Timer menu item and confirm the selection with C23 2010 04 12 10 14pm Timer 4 Absolute p Press orm to select the Absolute fixed time timer mode of operation then to confirm the selection The display returns to its default mode Table 7 9 Setting a Fixed time Off Timer
96. teel sheet painted Device rear panel Galvanized steel sheet Outer door Galvanized steel sheet painted stain less steel optional Door inner panel Stainless steel 1 4301 Control panel and display window protective foil Polyethylene Heater Thermo Scientific Silicone sheathed resistance heater wires stainless steel jacketed resistance heater wires with the IMH S model Heratherm 11 1 Disposal Overview of Materials Used Component Material Work space containers installed Stainless steel 1 4301 components and shelves Door frame seal Silicone Glass screen Sodium silicate glass Fan wheel Stainless steel 1 4016 Cables Plastic sheathed stranded copper wire Packaging Corrugated board polyethylene film and styrofoam chemically untreated wood 11 2 Heratherm Thermo Scientific A Error Codes Table 12 1 below lists the error messages that may appear in the control panel display window see Error Log on page 7 22 and provides instructions for clearing such alarms Table 12 1 Heratherm Incubator Error Codes Error Message amp Code Door Open Error E001 Root Cause The door switch IMH S Series only has triggered an alarm because the door has been open for more than 10 minutes Alarm Response Audible alarm activated alarm relay energized message shown on dis play Alarm Clearing Instructions Close the door Display E
97. th the cultures all accessories and other objects from the work space 2 Clean and disinfect the work space as explained in the section Cleaning and Disinfection on page 9 1 or if the above warning note applies run the dry decontamination routine at 140 C 284 F see Decontamination on page 7 16 3 When cleaning and disinfection and or decontamination are done turn the incubator off using the control panel 4 Unplug the power cord and secure it against accidental reconnection 5 Until the incubator is shut down the work space must be continuously ventilated Leave the glass door and the outer door open and secure them against accidental closure Thermo Scientific Heratherm 8 1 Shut down Shutting the Incubator Down 8 2 Heratherm Thermo Scientific LLL Cleaning and Disinfection Cleaning scAUTION _ conar Some incubator components are made of plastics Solvents may attack plastics Strong acids or alkaline solutions may cause embrittlement of plastics NCAUTION Moisture sensitive components Do not spray cleaning agent onto the control panel and the interfaces at the rear of the incubator When wiping the incubator clean always make sure that no moisture enters into these components Wipe the display window down with a slightly dampened cloth then wipe dry with a rag made of 100 microfiber Cleaning Exterior Surfaces Remove dirt residues and depositions thorough
98. that appears confirm the default selection Yes by pressing E 2010 03 29 4 05Pw Timer stopped The message Timer stopped appears as a confirmation The display will return to the main menu In the menu bar the Timer icon will go out Thermo Scientific Heratherm 7 13 Handling and Control Timer Table 7 15 Stopping a Weekly Timer Before It Expires Press to activate the menu bar then use QA to select the Timer icon and press to confirm a The flashing word On appears in the multifunctional Timer display pane 4 On gt Press to switch to Off state then press to confirm 2010 03 29 12 59Pm Timer 4 Off a The message Timer stopped appears as a confirmation Timer stopped In the menu bar the Timer icon will go out The display returns to the entry screen for the current type of timer 7 14 Heratherm Thermo Scientific Handling and Control Power Outlet table top incubators only Power Outlet table top incubators only This menu item IMH Series only toggles the built in AC outlet in the work space of the incubator on and off While the outlet is in live state the Power Outlet icon is illuminated in the menu bar Table 7 16 Turning the AC Outlet On Press to activate the menu bar then use UY to select the Power Outlet icon and press to confirm 2010 03 31 31 34PM q On Off gt In the selection
99. the Weekly timer mode of operation then to confirm the selection The display returns to its default mode Table 7 12 Setting a Weekly Timer Press to activate the menu bar then use 122 to select the Timer icon and press to confirm 2010 03 29 12 59PM Timer 4 On In the selection screen shown at left press 1223 to switch from the default On to the Edit option 2010 03 29 12 59PM Timer 4 Edit gt MENU Select the Edit option by pressing Thermo Scientific Heratherm Handling and Control Timer Table 7 12 Setting a Weekly Timer PTL ere Press to select the turn on time for Monday which POL ies d should start flashing when selected or continue to the EM desired weekday by pressing M which will cause the turn on time of that day to start flashing Press orm to set the hours then continue to minutes by pressing E Use or to set the minutes then continue to the turn off time by pressing SS Set the turn off time as explained above then press to continue to Tuesday or any other desired weekday To prevent the incubator from turning on and back off on a specific day set both hours and minutes to mSm cet the scheduled turn on and turn off times for each 4 Sunday p single day of the week all the way to Sunday and press On 1 AM Off PM ES The turn on and turn off times for Saturday and Sunday a
100. ubator and its accessories particularly if two devices are stacked The electrical circuitry of the incubator has been designed for an operating height of up to 2000 m above sea level Relative humidity up to 80 maximum preferably 60 70 non condensing Should condensation exist wait until the moisture has evaporated completely before connecting the incubator to a power source and powering up The ambient temperature must be within a range of 18 C to 32 C 64 4 F to 89 6 F Avoid direct exposure to sunlight Thermo Scientific Heratherm 3 1 Installation Intermediate Storage Devices that produce excessive amounts of heat must not be placed near the incubator Place the incubator on a floor stand option to be ordered separately never on the lab floor This prevents the penetration of dust or dirt into the device Power line voltage variations must not exceed 10 of the nominal voltage Transient surges must lie within the range of levels that normally occur in the power supply system The impulse withstand voltage based on surge category II of IEC 60364 4 443 shall be applied at the nominal voltage level Consider installing one dedicated upstream circuit breaker per incubator to avoid multiple device failures in case of an electrical fault Contamination hazard Do not place the incubator directly on the lab floor but mount it on the floor stand or on a lab work surface option t
101. vai 3 4 Figure 3 2 Floor stand incubators dimensions and required clearances eterne etos ttroannos 3 5 Figure 3 3 Floor stand incubators dimensions and required clearancesisccususcxtsvrsdvneondevsanntdsnssetennarondonsanraneianivvesanes 3 6 A o o A 3 7 Figure 4 1 Heratherm IMH 60 IMH 100 IMH 180 Front View eeso eoo teta rebar pl rines ear Yeh se cio OR a 4 2 Figure 4 2 Heratherm IMH 60 IMH 1007 IMH 180 Rear VIwicsasssseeeesk repetito bs petite beta vitia the koi 4 3 Figure 4 3 Heratherm IMH 60 S IMH 100 S IMH 180 S Series Front View eese 4 5 Figure 4 4 Heratherm IMH 60 S IMH 100 S IMH 180 S Series Rear View eese 4 6 Figure 4 5 Heather IMH 400 5 Series Front View secet rasihabts eia iones 4 7 Figure 4 6 Heratherm IMH 400 S Rear Visit 4 8 Fig re 4 7 Heratherm IMH 750 S Eront Vide AIR 4 9 Figure 4 8 Heratherm IM 730 5 Rear Vi ia A 4 10 Figure 4 9 Sensor System for table top IneuDatols small 4 12 Figure 4 10 Sensor System for floor stand incubators ssseesessssessesesrssssiststsstsrsrsrsesstsrsrsrsttrtstsrsesesstsrsrsreenesrsreee 4 12 Figure 4 11 Signal Interfaces and Power Socket cie ita 4 13 Figure 4 12 Connecting Nozzle for Fresh air Filters Accessory Item eene 4 15 Figure 4 13 Shelf System imissni dert e rin Un In A eR a om Ua 4 16 Figure 4 14 Tube Access Ogden retenta idad tdacin 4 17 Figure 5 1 Sliding the Retaining Spring into the Support Ball iiic pda ox R
102. wo 16 A slow blow fuses mounted on the incubator s main electronic circuit board protect internal circuitry from the impact of excessive power consumption Thermo Scientific Heratherm 4 13 Product Description Work Space Components Replacement should only be carried out by skilled and authorized qualified personnel of electrotechnology signal engineering N O LE Fuse replacement The device fuses are not user serviceable When the incubator exhibits the typical signs of a blown fuse no response to pressing the On Off button control panel remains extinguished no heating operation call Thermo Fisher Scientific Customer Service to have the fuses replaced Work Space Components Inner Chamber All components of the work space are made of corrosion resistant stainless steel and have an absolutely smooth and easy to clean surface Any embossings have a large radius Connecting Nozzles for Fresh air Filters Accessory Items Observe the following note for IMH Series and IMH S Series incubators with connecting nozzles for fresh air filters accessory item N Q TE Connecting nozzle for fresh air filters The connecting nozzle for the fresh air filter accessory item may neither be extended with nor be diverted through other tubing A fresh air filter can be attached to the connecting nozzle After puncturing the plastic cap the fresh air filter can be screwed onto the nozzle The conne
103. zed message shown on display Bridging across Klixon contact has failed Restart the device If this doesn t solve the problem call service Incorrect voltage E014 The applied voltage is too high or too low Audible alarm activated error message shown on display Apply the correct voltage as indicated on the name plate and acknowledge the error Sensor Error E100 Process sensor damaged The actual measured value is out of range Audible alarm activated alarm relay energized message shown on dis play Control transferred to reference sensor If both sensors are defective dis able all control circuits Call service Temperature Too High E101 Actual measured value exceeds permissible range The Triac is defective Process protection acti vated control continues on set value Audible alarm activated alarm relay ener gized E101 message shown on display If the error occurs repeat edly call service Temperature Too Low E102 Actual measured value falls short of permissible range Only on devices equipped with a door switch Audible alarm activated alarm relay energized message shown on dis play Temperature control continued Check the AC mains sup ply for an undervoltage condition and have the problem remedied if nec essary Check whether the incubator has been over loaded with samples If this is not the root cause of the problem c

User Manual - Laboratory ovens, furnaces

Contents

Download Pdf Manuals

Related Search

Related Contents