USER MANUAL - mPower Jump!
Contents
1. LIM TRUCK USER MANUAL Thank you for choosing the mPower Truck Jump Starter Always follow basic safety precautions when using electrical appliances Read all instructions carefully Please keep this instruction manual for easy reference rrivflowtticer_ technologies A PRODUCT LAYOUT Indicators m 12V Indicator E 24 V Indicator Test Butt 14V1A Input Battery Clamps B OPERATION GUIDANCE Switch Instruction 1 Test Button For checking battery storage level 2 Unit is Auto On Auto Off If unit does not detect voltage be sure to know the battery voltage system If voltage system is 12V press 12V button and hold for 2 seconds If voltage system is 24V press 24V button and hold for 2 seconds Indicators Press the test button to check the storage level of Jump Starter Indicator Unlit 5 Flashing 1 solid 2 solid 3 solid 4 solid 5 solid Storage level 0 10 20 40 60 80 100 The indicator will flash one by one during the period of charging Different numbers of solid indicators show different storage level of Jump Starter All indicator lights will turn off when charging is completed The 12V indicator will light up if voltage is detected and ready to jumpstart the 12V vehicle The 24V indicator will light up if voltage is detected and ready to jumpstart the2. 5 We do not assume responsibility for any loss or damage incurred during shipment or as aresult of a force majeure 6 We are not liable for any incidental or consequential damages arising from the use or misuse of this product 7 All warranty claims are limited to repair or replacement of the defective product and at the sole discretion of us 8 1f we repair or replace the product the product will be covered for the remaining time of the original warranty period Repair or replacement may involve the use of reconditioned units which are equivalent in function Replaced part or product becomes the property of us 9 Consumable components such as batteries are not covered by the warranty mPower Technologies Inc 777 Passaic Ave Clifton NJ 07012 VU 9 Overcharge and Overdischarge Protection Applied Standard GB T 18287 2000 C FC S ap RoHS The productis insured by Everest Fuse Protection Against reverse Plug
3. 24V vehicle 2 mPower Truck Jump Charging Instructions 1 Plug home adapter into the wall outlet 2 Connect 14V 1A input port of mPower Truck Jump to the other end of home adapter Or 1 Plug the car adapter into the socket of cigarette lighter 2 Connect 14V 1A input port of mPower Truck Jump to the other end of car adapter mPower Truck Jump Start Vehicle Instructions 1 Make sure the number of indicators is not less than 3 2 Connect the RED clamp to the vehicle s battery positive termi nal and connect the BLACK clamp to the vehicle s battery negative terminal 3 The unit will automatically identify the 12V 24V auto voltage intelligent identification function If unit does not detect voltage be sure to know the battery voltage system If voltage system is 12V press 12V button and hold for 2 seconds If voltage system is 24V press 24V button and hold for 2 seconds 4 Start the vehicle 5 When the vehicle is started disconnect the RED and BLACK clamps from the battery Leave the vehicle s engine running If there is no Jump start Reaction please operate as the following steps 1 Checking the battery clamps whether connected correctly if not the Jump Starter won t supply power to vehicle Please try again after connecting the battery clamps correctly 2 If the battery clamps are connected correctly but there is still no Jump Start and if little or no voltage is present manually
4. select 12V or 24V if you know your voltage system and hold for 2 seconds 3 Be sure to know your battery voltage system Do not select 12V or 24V if you do not know your battery voltage system It can be dangerous 4 If still no Jump Start after above steps please check the vehicle to see if there are other problems with the vehicle C PARTS LIST Parts Name Quantity 1 Host 1 2 Home adapter 1 3 _Car adapter 1 4 User Manual 1 D TECHNICAL SPECIFICATIONS Dimension 9 25 x 8 88 x 3 16 Weight 3 65 Ibs Output 12V Jump Start 24V Jump Start Starting Current 12V 500A 24V 250A Peak Current 12V 1000A 24V 500A Input 14V 1A Full charging time 8 hours Operating temperature 20 C 60 C 4 F 140 F Battery Type Capacity LiPo 88 8Wh E FAQ Q Can this product jump start 12V and 24V vehicles A Yes This product can intelligently recognize the vehicle battery voltage or you can manually choose the 12V voltage output accord ingly so it can jump start both 12V and 24V vehicles Q How many times can this product jump start the vehicle A Normally it can jump start 12V vehicles approx 30 times and can jump start 24V vehicles 15 times Q How long does it take to fully charge the jump starter A Approx 8 hours through the 14V1A input Q How long is the lifetime on this product A About 3 5 yea
5. e of flammable liquids gases or dust Do not modify or disassemble mPower Jump Plus Only a repair technician may repair this unit Do not expose the appliance to heat Do not store in locations where the temperature may exceed 158 F Charge only at ambient temperatures between 4 F and 140 F Charge only using the charger provided with the appliance Under extreme conditions battery leakage may occur Carefully wipe the liquid off using a cloth and avoid skin contact when you notice liquid on the batteries In case of skin or eye contact rinse immediately with clean water and seek medical attention At the end of their useful life discard the appliance with due care for our D 990 O YVUUHS environment and in accordance with government regulations I WARRANTY INFORMATION 1 We offer a limited warranty for this product against any defects in material and workmanship for a period of 6 months from the date of purchase by the end user consumer The conditions of the warranty are as follows 2 The warranty is only valid upon presentation of the original receipt from dealer retailer by the original purchaser with the product to be repaired or replaced 3 The warranty is void if the serial number date of purchase and label has been removed 4 The warranty does not cover damage or product failure resulting from normal wear and tear physical abuse improper installation misuse modification or repairs by unauthorized third parties
6. n 3 if so Don t attempt to jump start the vehicle 2 DO NOT connect the 12V vehicle battery system when the indicator light is on at 24V position 3 DO NOT connect the 24V vehicle battery system when the indicator light is on at 12V position 4 When 12V or 24V indicator light is on DO NOT connect vehicle battery positive and negative incorrectly It may be dangerous 5 DO NOT connect the battery clamps to vehicle battery by mistake 12V position connect 12V vehicle battery system 24V position connect 24V vehicle battery system Otherwise it may be dangerous 6 DO NOT connect the two clamps when both the 12V position and 24V position indicator lights are on Otherwise it may be dangerous 7 Remove the Jump Starter in 30 seconds after the vehicle is started 8 Always check if the jumper clamps are well connected check if the vehicle battery connector is rusted or dirty clean it before jump starting the vehicle DO NOT jump start again after 3 attempts Otherwise it will damage the host And check your vehicle if it has other trouble 9 DO NOT disassemble the host Otherwise it may be dangerous Always take care when using the appliance This appliance is not intended for use by young or infirm persons without supervision Do not use as a toy Do not allow the appliance to become wet Do not immerse the appliance in water Do not operate the appliance in explosive atmospheres such asin the presenc
7. rs Q How long does the battery last after fully charged A 6 12 months however we suggest you recharge it every 3 months F TROUBLE SHOOTING Finding Cause Remedies No response when Low voltage protection of Jump Plug the adapter into the pressing the test Starter is started 14V1A input port to button reset The appliance would be locked up Unlock it by holding down for safety protection which means test button for 5 seconds the short circuit may have been activated 12V 24V indicators are flashing frequently Findings Cause Remedies Do not use unit wait 10 minutes After cool down try again The storage level indicators are all flashing The battery overload safety protection is activated 12V 24V indicators blinking when connected to vehicle battery Red and Black clamps are Correct connections if reverse connected to the positive clamps are reversed and negative of vehicle battery Reverse Polarity Safety Protection is activated G TOXIC AND HARMFUL SUBSTANCES Composition and amount of toxic and harmful substances in unit Pb Hg Cd Cr Vi PBB PBDE O O O O O O O Indicate all homogeneous materials hazardous substances content are below the MCV limit specified in the Standard 2002 95 EC RoHs H Warning 1 Check the number of indicator lights is no less tha
Download Pdf Manuals
Related Search