6,000W Shop Heater
Contents
1. There is no user maintenance part except regular cleaning as following description All other servicing or maintenance should be performed by qualified service personnel Before any cleaning make sure that 1 Disconnect power supply at source Switch off the circuit breaker 2 Wait for 60 minutes to ensure the heating element has cool down and your heater is now ready for cleaning Regular Cleaning 1 Do not use cleaning liquid or other chemicals to spray on the unit 2 Interior dust can often be removed by using a vacuum cleaner with a crevice tool attachment 3 To clean enclosure use a clean soft and lightly damp cloth to gently wipe off the dirt from the surface of the unit Be sure not to wet the heating element and the switches Allow the unit to dry completely before using it CAUTION DO NOT ALLOW WATER TO RUN INTO THE INTERIOR OF THE HEATER AS THIS COULD CREATE A FIRE OR ELECTRIC SHOCK HAZARD DAMAGING THE UNIT If your heater fails to operate please follow these procedures This heater is intended to be a ceiling mounted heater It has a thermal cut off protection If the thermal cut off protection trips then switch 10 For technical questions call 1 800 665 8685 8553521 6 000W Shop Heater V 3 05 off the power Switch off the circuit breaker The unit should reset automatically after 10 minutes If the thermal cut off protection trips again consult a certified electrician to determine the reason for2. overheating Problem Probable Cause Solution Unit is not Overheat protection has Turn the heater OFF Switch heating temporarily deactivated off the circuit breaker Wait 10 the heater minutes before turning on the heater Room temperature has To increase the room been warmed up to temperature adjust thermostat thermostat setting control knob to a higher setting Breaker Fuse has been tripped Check your electrical box to confirm the breaker has not been blown This may occur if the receptacle is shared between other high consumption appliances The Check amp ensure there are no Remove any combustible items heater is combustible materials within from the heater producing 0 9 meters 3 feet surrounding a burning the heater smell A drop of oil fell on the heating Ensure room in which heater is coil during the manufacturing situated is well ventilated process It will quickly evaporate and should not occur again Ensure a minimum clearance of Reposition the heater so there is 36 inches 90 cm from both enough space around the heater sides and rear of heater to to the adjacent walls adjacent walls PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF DOING SO COULD CAUSE DAMAGE OR PERSONAL INJURY Visit www princessauto com for more information 11
3. minimum distance must be maintained 2 Do not install closer than 1 foot or 0 3 m to any adjacent vertical surfaces or walls 3 Keep at least 4 5 inches 11 5cm from the back wall with or without using the wall hanging mounting bracket 4 Mark the drill hole positions in the wall or ceiling for the mounting bracket 5 Drill the required holes with diameter fit for the anchor provided for positioning the mounting bracket 6 Insert the anchors 7 Attach the mounting bracket to the wall or ceiling and secure with mounting screws 8 Hook the unit to the mounting bracket and let the unit hang from the mounting bracket 7 48 Nin CEILING MOUNT WALL MOUNT Visit www princessauto com for more information 7 V 3 05 6 000W Shop Heater 8553521 9 Insert the screw through the mounting bracket and the heater handle tighten the nut 10 Loosen the screw to remove the wiring compartment connection cover in the rear of the heater 11 Run the electrical power supply cable in flexible conduit and connect to the wiring compartment via the knock out at back side of the unit 12 Make the connections properly with connectors which are suitable for the conductor size including grounding wirings After making the connections arrange the pigtail leads of unit and power supply wires in the wiring compartment 13 Replace the wiring compartment connection cover and lock in place with the screw WARNING The heater mus
4. ING Read all instructions before using this heater 2 This heater is hot when in use To avoid burns do not let bare skin touch hot surfaces Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least 3 ft 0 9 m from the front of the heater and keep them away from the sides and rear 3 Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended 4 Always switch off the heater when not in use 5 Do not operate any heater after the heater malfunctions has been dropped or damaged in any manner Disconnect power at service panel and have heater inspected by a reputable electrician before reusing 6 Do not use outdoors 7 To disconnect heater turn off power to heater circuit at main disconnect panel 8 Do not install less than 8 feet 2 4m high from the floor and closer than 1 foot 0 3m to any adjacent vertical surfaces or walls Keep at least 4 5 inches 11 5cm from the back wall with or without using the wall hanging mounting bracket 9 Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the heater a a S E E O E E Visit www princessauto com for more information 3 V 3 05 6 000W Shop Heater 8553521 10 To prevent a possible fire do not block air intakes or exhaust in any manner 11 A heater has hot an
5. V 3 05 8553521 PRO POINT 6 000W Shop Heater User Manual e U us LISTED E360195 Please read this manual before use V 3 05 8553521 PRO POINT 6 000W SHOP HEATER SPECIFICATIONS BTU Rating 20 472 BTU Heating Capability 600 sq ft Heat Settings 3 000 6 000W Current Rating 25A Voltage Rating 240V Feature s Adjustable thermostat Hi Low switch and auto reset overheat protection Adjustable tilt and louvers to direct heat where you need it most Additional Info Powder coated steel construction Overall Dimensions 16 3 4 x 17 3 4 x 15 3 4 in CUL CUL KKWS 7 E360195 l For technical questions call 1 800 665 8685 N 8553521 6 000W Shop Heater V 3 05 IMPORTANT INSTRUCTIONS PLEASE READ ALL INSTRUCTIONS BEFORE USING THIS HEATER NOTE There may be a trace of smoke or odor when unit is first operated Don t be alarmed This indicates that a drop of oil fell on the heating coil during the manufacturing process It will quickly evaporate and should not re occur Make sure that the room in which the appliance is located is well ventilated during this operation It is normal for the appliance to emit small cracking sounds when you turn it on for the first time Do not be alarmed WHEN USING ELECTRICAL APPLIANCES BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE RISK OF FIRE ELECTRICAL SHOCK AND INJURY TO PERSONS OR PROPERTY INCLUDING THE FOLLOW
6. a thermostat setting e Ambient temperature is regulated by adjusting the thermostat to a desired position Allow the unit to operate and warm up the room When the desired temperature is reached turn the control knob counterclockwise until the heater turns off This is your ideal setting The heater will start automatically when the room temperature drops below this set point and will turn off when the set point is reached To turn off the heater switch off the circuit breaker The circuit breaker serves as the power disconnection means e This heater includes a visual alarm to warn that parts of the heater are getting excessively hot If the alarm flashes immediately turn the E Visit www princessauto com for more information 9 V 3 05 6 000W Shop Heater 8553521 heater OFF and inspect for any objects on or adjacent to the heater that may cause high temperatures DO NOT OPERATE THE HEATER WITH THE ALARM FLASHING To reset the heater switch the circuit breaker OFF and wait five to ten minutes for the unit to cool down before turning the heater on There is no user maintenance part except regular cleaning as following description All other servicing or maintenance should be performed by qualified service personnel Before any cleaning make sure that 1 Disconnect power supply at source Switch off the circuit breaker 2 Wait for 60 minutes to ensure the heating element has cool down and your heater is now ready for cleaning
7. d arcing or sparking parts inside To reduce the risk of fire Do not use it in areas where gasoline paint or flammable vapors and liquids are used or stored 12 Use this heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons 13 This product must be installed by a certified electrician in accordance with local codes 14 For supply cables use 10 AWG 5 3 mm copper wires 15 This heater includes a visual alarm to warn that parts of the heater are getting excessively hot If the alarm flashes immediately turn the heater OFF and inspect for any objects on or adjacent to the heater that may cause high temperatures DO NOT OPERATE THE HEATER WITH THE ALARM FLASHING To reset the heater switch the CIRCUIT BREAKER OFF and wait five to ten minutes for the unit to cool down before turning the heater on CAUTION High temperature risk of fire keep electrical cords drapery furnishings and other combustibles at least 3 feet 0 9 m from the front of the heater and away from the side and rear 4 For technical questions call 1 800 665 8685 8553521 6 000W Shop Heater V 3 05 SAVE THESE INSTRUCTIONS WALL CEILING MOUNT HEATER Model PH 960 Volt 240 V Watts 6000 W Frequency 60 Hz BTU h 20472 WIRING DIAGRAM SOW 300W AND HEATER START AC240V 60HZ 1P Visit www princessauto com for more informatio
8. n 5 V 3 05 6 000W Shop Heater 8553521 A Upper Enclosure B Tilt adjustable knob C Front Exhaust Grill D Louver for air direction E Control panel F Power Indicator G Alarm LED H Rocker Switch High Low select I Temperature Setting Knob WARNING All wiring must be installed by a certified electrician according to the electrical safety The ceiling heater must be grounded in accordance with all national and local building codes All Wiring procedures and connections shall be in accordance with the national and local codes having jurisdiction S 6 For technical questions call 1 800 665 8685 8553521 6 000W Shop Heater V 3 05 BEFORE INSTALLATION Disconnect the main supply connection Supply cables shall be 10 AWG 5 3 mm copper wires The heater must be connected to individual branch circuit protected by 35 Amp circuit breaker only Supply cables must be equipped with a dual pole circuit breaker rating at least 240V 35A pole as main cutoff switch of power connection to the heater CAUTION High temperature risk of fire keep electrical cords drapery furnishings and other combustibles at least 3 feet 0 9 m from the front of the heater and away from the side and rear WARNING To reduce the risk of fire do not store or use gasoline or other flammable vapors and liquids in the vicinity of the heater INSTALLATION INSTRUCTION 1 Keep the unit at least 8 feet 2 4m away from the floor This
9. t be properly installed before it is used SSS eed 8 For technical questions call 1 800 665 8685 8553521 6 000W Shop Heater V 3 05 HAZARD OF ELECTRIC SHOCK EXPLOSION OR ARC FLASH e Apply appropriate personal protective equipment PPE and follow safe electrical work practices See NFPA 7OE e A circuit breaker must be installed and serviced only by qualified electrical personnel e Always use a properly rated voltage sensing device to confirm power is off The Select switch on the heater is only for function selection Use circuit breaker as power ON OFF device The circuit breaker is to be installed by certified electrician and shall be located in line of sight from the heater location or shall be capable of being locked in open position Follow the operating instruction to reduce the risk of fire electric shock injury or death to persons e Switch on the circuit breaker to turn on the heater e Then turn the thermostat to the farthest clockwise position The fan should start and the unit begins heating the room and lamp is light After the room reaches comfort level turn the thermostat counterclockwise until the heater shuts off The heater will automatically cycle around this preset temperature To increase the temperature turn the thermostat knob clockwise To lower the temperature turn the thermostat counterclockwise e Press the switch to High or Low position for heat selection HIGH 6000W LOW 3000W e Select
Download Pdf Manuals
Related Search