Installation Guide
Contents
1. on the left small hole on the bottom of device see following figure Use the tool plug into the hole refer to the picture on right then plug out The machine is able to restart Reset key 4 2 Anti dismantle button Anti dismantle button is on bottom of device whose function is realized by back cover pressing the anti dismantle button When the device is being dismantled it will send a alarm signal through the terminal 18 F10 Installation GuideV2 2 4 3 Built in EM card reader Optional Built in a contactless EM card reader module the distance of flashing card is 5 10 cm it completely supports the thick card 1 88mm middle card 1 05mm and thin card 0 88mm whose operating frequency is at 125 KHZ the card area as following illustration 4 4 Built in MIFARE card reader Optional Contain a contact less MIFARE card reader module the distance to detect card is 5 10cm it completely supports MIFARE cards that provide operating frequency 13 56MHZ communication speed 106KBPS the card area is as following illustration RF area Trouble Shooting 5 Trouble shooting Trouble Cause amp Measure Power LED is off Cause No power or lack of voltage Measure Check and examine the connection of PWR GND make sure they contact well Measure the supply voltage ensure that it is 12VDC Device is unable to connect with PC Cause The connection problem Measure Check and examin2. when there is no external reader No mater what you must cut this wire and wrap it to keep away short circuit You must ensure that hookup is correct follow the above table before power up and use Installation 3 2 Connect with Peripheral Equipment To help avoid possible damage serious damage to equipment before connecting or disconnecting Peripheral Equipment should ensure disconnect power from system by unplugging power cable Please observe and follow the guidecable to connect the external equipment Access Controller An external card reader Alarm p various network F10 Installation GuideV2 2 supporting auxiliary communication interface Power supply 3 2 1 Connect to the Access Controller F10 as a fingerprint reader until it connect with the access controller unable to work alone only serve as a fingerprint identification front end for system and provide the controller with a standard or self define Wiegand signal such as other Proxy Card Reader adopt the standard signal D0 D1 GND connection method see standard connection illustration These extension wire LED Red LED Green Beep Out are used to get Installation signal from the Access Controller Depending on the Access controller setting to control the red green Indicator beep which produce the corresponding active for linking way please refer to the reader connect with alarm Notice Whatever the power of F10 s
3. distance and the network to 485signal stability RS232 485 converters drive capability no enough Measure D the farthest distance of communications theory between fingerprint reader and access controller is the 1 200 meters actual project is not recommended more than 500 meters after more 22 F10 Installation GuideV2 2 than plus repeaters communication baud rate adjust to 9600 3 RS485 bus in the starting point of terminal equipment and at the end of terminal equipment match with terminal resistance resistance is about 120 9 improve communications surrounding environment use a good shielding cable and smaller distributed capacitance wires to reduce external interference Cut off power of fingerprint reader one by one then perform an machines troubleshooting step by step mounted over the network reducing the number of machines or to increase all the way RS232 485 converters and 485 network proposed RS232 485 converter with power Some users finger prints sometimes can t be verified Cause The fingerprint quality is poor Measure You d better select fine fingerprint less crinkle no desquamation clear image when enroll fingerprint make your finger touch fingerprint sensor with larger area a comparable test should be made after enrollment we suggest you enroll more fingerprints By the way our device supports 1 1 match method and password identified function yo
4. up network using 9600 baud rate Only increase this data rate after the system is operating properly at 9600 uonensn i uonoeuuoo piepuels System Configure Japesy Jeujo 014 J lolluo 9 OLA Jo 0 ju0 7 2d Oo opyok IQ ewuwuseub Td eytuwueeb ss 0d woje ot ueeJb uee16 0 aa G4oejq IND yoeIq IN 0e q 0N oce eyuwpe AGT pe A pes AG JapaAU0D aS8h sewzezsu vegt F10 Installation GuideV2 2 3 Installation 3 1 Install back panel This product is designed for indoor installation if it has to be installed it outdoor please place the equipment in proper surroundings you must beware of not exposing it to water or harsh condition we remind to cover up the cable into the wall if it isn t capable to do you must obtain the user s permission before to install Locate a comfortable height for finger place firstly use the screwdriver along with the unit to turn off the screw in the bottom of the unit and take away mounting plate there are four fix hole in the mounting plate see right illustration a b c d keep secure it on the wall using supplied screw and fix the F10 reader body on the mounting plate please strictly complied with the wire definition and colour after finish the hookup cut the expose part of the unwanted wire especially red white wire and use the insulating tape to wrap it because the red white wire provide a output 12VDC voltage
5. F10 Installation Guide F10 Installation GuideV2 2 Contents Before Inst lling nae uns e d 1 1 1 Notice about installing i 1 122 FIO DeSGriptioni iiiter eee eee e ERR eG 3 2 System Configuration sa 5 2 1 Standard connection illustration sse 5 3 Installation ois cet set cete e tait J 3 Install back panel i 7 3 2 Connect with Peripheral Equipment 8 3 2 1 Connect to the Access Controller 9 3 2 2 Connect to Alarm i 11 3 2 3 External Reader una assaka 13 3 2 4 RS485 connection sss 14 3 2 5 Complementary communications 15 3 2 6 power connections as oia 16 3 3 fixed fingerprint machine essen 17 dorso ao ai ii da cal ni ni nio 18 4T ReS6b ccn ect eee Ra rete 18 4 2 Anti dismantle button i 18 4 3 Built in EM card reader Optional 19 4 4 Built in MIFARE card reader Optional 19 5 Trouble shooting uim ie ter iE Ee 20 F10 Installation GuideV2 2 1 Before Installing 1 1 Notice about installing Access Control Station is a mass produced product It strictly tested comply with the standard of China U S A and EU This file contains important in
6. about 50 mA operating current of about 300 mA please use only approved the power adapter the power adapter must be rated for the product and for the voltage and current marked on the product s electrical rating otherwise it will cause serious damage See standard connecting figure Power requirements DC 12V 2V 1A Note F10 directly power on through the power supply of the access controller can also be an external sources of power The define of terminal connection Terminal Functional GND Cathode 12V Positive DC 12V F10 Installation GuideV2 2 3 3 fixed fingerprint machine After be sure all cable are inserted correctly into fix installed backplane and mount F10 on the backplane Note Please strictly in accordance with the definition and color to connect and connect completed All exposed part of connection wire end cannot be exceeded 5mm to prevent the bared wire accidental connection which leads to machine break down in particular the red cable as a 12 V output voltage when there is no an external card reader in any case ensure to cut this cable and use the insulation adhesive plaster to dress it so as to avoid short circuit 17 Installation 4 Others 4 1 Reset Due to operation error or other accidence which leads the machine not to work you can restart machine through reset key take a small tool which diameter is no more than 2mm find reset mark of res
7. e the connection of RS232 RS485 or TCP IP whether its connection is correct or not After power is on LCD device display shows Please try again always Cause For long time used surface of fingerprint sensor becomes dirty or there are some scratches on it the device takes it as a Fingerprint connection cable of fingerprint sensor is loosed 3 fingerprint and does verification Chip on board is broken Measure 1 Under such situation you can use scotch tape to adhibit the dirt 8 Need to contact suppler and ask for repair Startup bar cycles and can t enter menu Cause D Fingerprint connection cable of fingerprint sensor insert improperly Fingerprint sensor broke down Chip on board is broken 20 F10 Installation GuideV2 2 Measure D Please take out the Fingerprint connection cable from slot of fingerprint sensor plug it again 3 It need to contact suppler to repair WIEGAND output problems After correctly match fingerprint or punch card but the controller can not accept the card number or numbers error Cause communication distance between fingerprint reader and access controller is too long poor communications environment Access Controllers request fingerprint reader have a stronger signal drive capability 4 Output circuit damage put a multimeter to DC profile and measure WDO WD1 pin when verification
8. formation It is better for you to read it carefully prior to use If you ignore it the incorrect installation may cause the unit damage Although we could do our best to offer you service the neglect to the file could cause unwanted cost for you 1 Before installation please make sure the power is cut off because it is very dangerous if the power is on The short circuit of power cable may cause the core parts damage 2 All exposed part of connection wire end cannot be exceeded 5mm to prevent the bared wire accidental connection which leads to machine break down And also suggest using different color cable to connect 3 In the place where the static is strong or in winter please connect the grounding firstly in order to prevent the instant mass static damage the machine 4 Connect power supply with device in the last for the wiring connection If you find any unusual thing occur please firstly cut off the power then go to examine Keep in mind wiring operation under power on will lead to machine sudden damage we are not liable for damages System Configure and trouble due to such operation 5 The height to mount device is about 1 4 1 5 meter 6 After installation please take off protection film on the fingerprint sensor to get best recognize result 7 After installation finish when go to test the exit door button please keep a personal in the outside because sometimes the accidental issue can bring on you are
9. nate this disturbance traditional RS485 networks require a 120 terminal resistor to be installed at the end of the bus cables based on the physical layout of the pair twisted cables In the normal condition the resistor is not installed only if the bus is extended to over 100 meters the termination must be connected with a terminal resistor The define of terminal connection 5 PIN Terminal Function 485A RS 485 communication 485B RS 485 communication GND Ground Spare Spare F10 Installation GuideV2 2 qospa 485B e 485A 4858 RS485 Bus 485A tal RS485 Converter For RS232 Communication g E For TCP IP Communication Cable 8PIN cable provides Ethernet and RS232 connection connection method shown above Special Note there is a assisted communication interface at the device bottom that do not need to remove the machines establish a connection 15 Installation through cable so when the official use in any case must be set up communications password that is passwords for equipment and software communications Software to set your own The define of terminal connection 5 PIN Number of terminal Functional TXO RJ45 1 TXO RJ45 2 RXI RJ45 3 RXD TXD of RS232 GND GND of RS232 RXI RJ45 4 TXD RS232 AY RXD Spare 3 2 6 power connections F10 power supply is 12 VDC standby current
10. not able to go outside 8 it is good a idea to use more than 12 V 1 5A independent DC power supply with this equipment and the controller or to reduce the electric locking interference current ripple wave is less than 150 mV 9 When the system power supply from Access Controllers should pay attention to the drive output capability of Access Controllers Access Controller should be able to provide more than 500 mA current 10 when hook up the Fingerprint reader network with the cable 8 shielding cable RVVP 8X0 3MM2 is recommended to reduce the interference in the course of transmission please read and always follow Quick connect Guide closely Because the wrong wiring will cause the core block and sensor to burn out insult in device to break down at this cause ZK Software is not liable for any damages and trouble 11 12 V DC power supply cable by two core power cord RVV 2X2 5MM2 If the space between power adapters and device is too long please do not use the twisted pair or other type ferrules for the power wire When the power wire is selected you should pay attenuation for voltage which has passed long distance transfer F10 Installation GuideV2 2 12 Please use specialized RS485 cable the internationally popular RVVP shielded twisted pair is recommended Model RVVP 2x0 5 1 5mm2 two core shielded twisted pair and the RS232 485 converter with power to hookup the network the bus structure apply to connect with each de
11. successful two pin voltage is subject to fluctuations without fluctuations or 0 V the circuit has proved that damage Measure D fingerprint reader and access control communications controller farthest distance of 100 meters after more than to increase conversion circuit improve communications environment use a good shielding cable to reduce external interference the first WIEGAND output signal of the fingerprint reader will be modified adjust low pulse cycle to 500 uS adjusted cycle to 2 mS and then through adding the resistance offset input pull up resistor of the Access Controller will be contact vendor for 21 Trouble Shooting warranty The fingerprint sensor light is off Cause D Fingerprint connection cable of fingerprint sensor connection is broken fingerprint sensor broke down Measure D Please take out the FFC from slot of fingerprint sensor plug it again 2 Contact suppler ask for repair Failed RS485 communication Cause D RS485 communications cable miss connection on the contrary communications baud rate is too high In the proposed multiple device networking as 9600 too far distance of communication or poor communication environment among network a RS485 chip of the fingerprint reader damage caused network paralysis two machines have the same address mounted over the network the machine will be affected too much to the network transmission
12. the mounting plate to keep press the button T Alarm connection 12 F10 Installation GuideV2 2 3 2 3 External Reader F10 utilize the function of wiegand input to support a external reader at the same time F10 connect external reader via standard way and the pin of reader D0 D1 12V according to the pin of F10 Wiegand In DO Wiegand In DI GND 12VOUT one by one to connect see standard connection Illustration Special Notice when there is a Mifare module in the F10 the Wiegand input is invalid if there is no external reader don t need to do this connection Definition terminal connection 3 PIN Number of terminal Function 1 GND Ground 2 IWDI Receive wiegand signal data 1 3 IWDO Receive wiegand signal data 0 Card reader Installation 3 2 4 RS485 connection RS 485 systems using a bus structure configuration connect the driver to the receiver The transmission cable is made by a group of pair twisted cable Each transmitted signal has a pair of conductors consisting of inverted and non inverted signal Cable The inverted cable is generally indicated by the index A or with the non inverted cable designated as B or The receiver simply evaluates the difference between the two Cable so that common mode noise on the transmission cable will not result in a falsifying of the actual signal however on the cable may be produced a difference mode disturbing In order to elimi
13. u could choose one of them 23 Information in this document is subject to change without notice Printed in China
14. upply by the access controller or doesn t it the two equipment s GND must be in common connection Do not replace Weigand signal power GND with GND of powe to ensure transfer the wiegand signal steady please separately plot wiring e lt gt lt gt WDO SS gt ET WDI SS Specifications TDW pulse 100 um TIW cycle 1 mm Output drive capability 200mA F10 Installation GuideV2 2 Definition terminal connection 7 PIN Cable Number of terminal Functional 1 GND Ground 2 WDO output signal wiegand data 0 3 WDI output signal wiegand data 1 4 Spare 5 Spare 6 Spare 7 ALM alarm signal 3 2 2 Connect to Alarm F10 can connect a signal alarm to system which mainly use to remind Installation that the F10 has been dismantled no matter what condition when it is removed F10 will trigger alarm output brown wire in the power on state in normal condition the wire doesn t send any signal F10 will link GND through the wire if the system be trigger follow this principle we can achieve the remind function of dismantled alarm connect the cathode of alarm power to alarm output brown wire the positive of alarm power link to the positive of F10 power see right Figure F10 alarm output only support 12VDC alarm Notice There is a button to anti dismantle in the bottom of F10 realize function is to utilize the cylinder on
15. vice When a long cable is used to transfer signal it is need to connect a matching resistance to receiver and its value is 1200 13 Signal cable such as RS485 cable and high power electricity cable do not such as AC electric locking cable place in parallel not put in the same pipe Other more details items please see also the user manual the operating instructions and the appendix and so on 1 2 F10 Description Pass Fail Indicator amp Button Fingerprint Sensor Power Indicator Pass Fail Indicator amp Activate Button The indicator glow green which the flash interval is 1sec in normal ready working state and constantly glow green for 3 sec as the identification is positive if the authentications fail it will constantly glow red light for 3 sec When the sliding ID card or Mifare Card nearby RF sense area of the reader if the card to be verified is valid the indicator displays rapidly green flash System Configure it interval time is 1 sec press this button to activate the reader while it in normal working state and wait for 3 sec switch the reader into idle state Fingerprint Sensor Enroll or match fingerprint Power Indicator It constantly glow green in the normal supply or idle state F10 Installation GuideV2 2 2 System Configuration 2 1 Standard connection illustration There are two ways RS 485 Ethernet to create network for F10 see standard connection illustration RS 485 network Set
Download Pdf Manuals
Related Search