USER GUIDE TO THE ARENA OPERATION
Contents
1. 14 Viewing and editing the routing III 1 It s possible to modify the routing parameters per channel from its Routing button Pre Post Fader Str MonoL MonoR Mono L R Active sends Non active sends 15 Page change Press A V Take into account that if the Memory function is activated the first page will appear as A Activating channels 1 Activate E or deactivate E Take into account that working in Bus Send Mode the ON button will work as ON OFF and the OFF button will work as CUE 16 Control of external equipment AEQ codec and hybrids 1 Previously we have defined two three keys per equipment 2 When a call is received the RING WAIT button starts flashing To get the call and send the codec to WAIT mode pres the button To put the codec ON AIR press the other key ON AIR 3 With a Cleanfeed function or acting over the routing we can decide the signals sent as a feedback to the codec Any output can be MixMinus or N X SEE CLEANFEEDS PAGE 17 Studio selection 1 Previously we ll have defined the studios and their assignment of signals Remote PFL Cough cut Monitors Green and red light relays 2 Select the studio Max 3 with red and green lights Max 7 with red light only 3 Set the signals sended and the level 18 Execute a salvo or a GPO 1 Previosuly we ll have defined in the SW the salvos gpo s and the keys ass2. menu and accept e 3 Select the desired Mode Stereo Mono L Mono R Mono L R lt gt and accept e 4 Do the same way to select the Phase L R L R L R L R r 7 YPE ORMAT 6 Stereo Ainolog CUE Monitoring inputs as PFL outputs as AFL 1 Press the CUE button of the channel s 2 Select the listening level with the CUE pot 3 Watch level and phase of the CUE bus 4 Deactivate the sends to PFL by pressing the PFL buttons of the channels sended to CUE or pressing the CUE RESET to deactivate all the CUE sends at the same time Control Room Monitors and headphones 1 Select the default signals to monitor in the SW Choose if they are exclusive or non exclusive 2 Select the listening level with the MONITOR or HEADPHONES encoders 3 Activate the signals LL 4 If want to listen other PTTILLLi signal s press the F5 Monitor or Headphones encoder turn it until you find the desired signal and press the encoder to select it Go back to step 2 Applying a Dynamic effect 1 Press the DYN button 2 Move over the effect to apply A Y Compressor Noise gate Delay or Rever 3 Select ON OFF lt gt and accept e A Heseeee Eres Applying an EQ effect 1 Press the EQ button 2 Move over the effect to apply A Y Equalizer or Filter 3 Select ON OFF lt gt and accept e 10 Selecting another Preset f
3. of a microphone adjust the sensitivity and activate or not the 48 v Phantom power Processing 1 Press SELECT 2 Select PROCESSING using the third encoder and pressing it to select 3 Select the desired effect Equalizer Filter Delay Compressor Reverb Noise gate 24 Processing II 1 Vary the parameters with the encoders and keys 2 Save or load the presets 3 Save or load the group of effects stored for a channel 2 Sa ee HECE 2st ae 25 Talkback 1 Select the output level of the talkback mic Select where to send the orders f i 1 J a x Studio monitors m y 7 A 5 i Primary headphones group m Secondary headphones group m 3 Or select to send orders to all at the same time m 26 User change 1 Select CHANGE USER 2 Move over the user with the third encoder and select it pressing the encoder Load the selection Activating the clock manually 1 Select TIMER FUNCTIONS 2 Start in manual mode 3 Reset the counter Activating the timer manually Select TIMER FUNCTIONS If it is not selected press IMER 1 2 Select the initial time 3 Start Stop 4 Elapse i IR PTTIiiiti E aE ee j i ee ETTEN unnsa Ja EENE Save Load a memory 1 Select WORKING CONFIG 2 Select the memory with the third encoder and select it e 3 S
4. USER GUIDE TO THE ARENA OPERATION The mean of this guide is to help as aa quick reference guide to the operation of the most common functions of the ARENA console It is not a substitute of the operation user manual Software configurations previous to the operation are not included DEFINITIONS Movement through menus of the displays at the top Buttons are represented as A up down lt left right y accept g Rotary encoder turn to vary a value and press to accept Page swap keys Represented as A and V Cy Programmable key It can be defined as PTT Push to Talk au Selection key of the main display of the DM module ON OFF channel keys a Fader Assign signals to faders 1 Set in the SW which signals are selectable at each fader 2 Press the encoder 3 Press three times Up A A A to go to Input menu and accept e 4 Turn the encoder to select the desired signal and accept 5 Leave the screen pressing the encoder o going to Exit V V V and accepting e Vary the input gain 1 Turn the encoder 2 Select gain between 12dB and 12dB for line inputs and 24 y 24 dB for microphones Vary the Ballance of a channel 1 With the textL_ Rin the channl display activate the ballance pressing the botton right next to the encoder 2 Vary the ballance turning the encoder Vary Mode and Phase 1 Press the Input Gain encoder 2 Press twice Up A A to go to Mode
5. ave Load Delete the selection MEMORY CON IGURATION SELEC NEM al lave mamn TH CURRENT t Save Load a configuration 1 Select WORKING CONFIG 2 Select WORKING CONFIG 3 Select the configuration 4 Save Load Delete the selection SELEC NEW a WORKING DELETE LOAD SAVE CONFIG SELECTN SELECTN CURRENT J f 7 F pales E l 1 MACRO AOM TM WEMORY CANCEL LOAD SAVE SE E CONFIG SELECTN SELECTN CURRENT Load the Programmable keys config 1 Press MACRO CONFIG 2 Select the configuration to be applied 3 Load it 32 System Setup 1 Select SYSTEM SETUP 2 Write the password if it was defined in the sw with the programmable keys 1 to 8 3 Choose an option Change the frame and console IP s 1 In the System Setup select Mixer address or Frame address 2 Turn the encoder to vary the value and press the encoder to vary the field 34 mn lan See the DSP conssumption 1 In the main display we see the dsp conssumption of the dsp 2 boards assigned to effect 2 In the System setup selecting Dsp Cpu ae a used the amount of dsp on CONF JSER me process per dsp and its AT TITTI EENNHENHNN function is shown ng TETERE Sennnnne Bees 5 pee OOo Evros Disconnect all audio process DSP 1 From the System setup select Disconnect all audio Process Check the Firmware versions 1 From t
6. he System setup select Firmware version information 36 Check signals DSP assignment 1 From the System setup select Dsp Output List 2 Check the signals controlled by each DSP board To change the shown DSP press the encoder Changing date and time 1 From the System setup press Date or Time Turn the encoder to vary the value and press it to change the field SET Ea k IGITAL STUDIO LO 38
7. igned to them 2 Press the key to activate the salvo or gpo When you press the key again the inverse action is executed P S it is possible to define the behaviour of the keys as a PTT where the action is active while the key is press and the inverse function is executed when you release the key 19 Cleanfeeds 1 Previously we ll have defined in the sw the keys assigned to Cleanfeeds outputs 2 Keep the Cleanfeed key pressed 3 The signals sent to the cleanfeed are shown by its routing button blinking If it is blinking the signal is being sended and if not it is not being sended an you can send it pressing the routing button 4 Once the desired channels are sended to the cleanfeed release the key 20 Info amp setup display operation 1 Press SELECT 2 In the DM display all the information of the channel is shown Processing Tone and noise generation I O setup 3 To move through the menus we use the 3 encoders and the 5 keys next to the display 21 Test signals generation 1 Press SELECT 2 Select TEST SIGNAL GENERATION using the third encoder and pressing it to select 3 Select Tone Pink Noise or White Noise 4 Select the level in every case and frequency for the tone L a I O Setup 1 Press SELECT 2 Select INPUT OUTPUT SETUP using the third encoder and pressing it to select 3 Vary the Phase and Mode In case
8. or an effect 1 Press the DYN 6 EQ buttons 2 Move over the effect to apply A Y 3 Move over the preset gt gt gt and accept e 4 Select PRESET LIST gt gt gt and accept e 5 Select the desired preset A WV and load it LOAD 11 Varying the parameters of an effect 1 Press the DYN or EQ button 2 Move over the effect to apply A WV and accept e 3 Select the preset lt gt and accept e 4 Select CHANGE PARMs gt gt and accept e 5 Select the parameter to vary A Y and modify it with the encoder Viewing and editing the routing Press the Up or Down buttons A W to see the complete routing of the 10 channels of a page It can be necessary to do a scroll pressing Down Menu e A send is activated when the symbol is shown and deactivated when is shown ENRSNENNE U Pressing the encoder and aes turning we access to the sends of the channels and we are able to activate or deactivate them with the contiguous button With the light on the send is activated and viceversa Swen TTTTITin 13 Viewing and editing the routing II 1 Press the ROUTING button to see the complete routing of the channel It can be necessary to do a scroll pressing Down Menu e 2 Activate and deactivate the sends moving with the scroll WV A and pressing the button e A send is activated when the symbol is shown and deactivated when is shown
Download Pdf Manuals
Related Search