Razor Beam
Contents
1. Sh Razor Beam 5 x 9W CW Beam Bar User Manual Order code LEDJ264 Safety advice WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP e Before your initial start up please make sure that there is no damage caused during transportation e Should there be any damage consult your dealer and do not use the equipment e To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual e Please note that damages caused by user modifications to this equipment are not subject to warranty CAUTION CAUTION TAKE CARE USING KEEP THIS EQUIPMENT THIS EQUIPMENT AWAY FROM RAIN MOISTURE AND LIQUIDS HIGH VOLTAGE RISK OF ELECTRIC SHOCK IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other If the equipment is dropped or damaged disconnect the cables Handle the power cable and all mains voltage mains power supply immediately and have a qualified connections with particular caution engineer inspect the equipment before operating again e Never remove warning or informative labels from the unit If the equipment has been exposed to drastic Do not open the equipment and do not modi2. For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA cable DMX cable requirements for DMX operation This fixture can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output see image below Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers Please quote CABL10 2m CABL11 5m CABL12 10m Note DMX cable must be daisy chained and cannot be split www prolight co uk Razor Beam User Manual 10 DMX setup Notice Be sure to follow the diagrams below when making your own cables Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out DMX 512 in 3 pin XLR 3 pin XLR EN ne OM RENEE XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground o Pin 2 Negative 3Hot 3Hot Pin 3 Postive Special note Line termination When longer runs of cabl
3. LEDJ264 Om 1m 2m 3m 4m 5m 400mm 225mm WWO8 PN www prolight co uk Razor Beam User Manual 3 Technical specifications POWER IN RAZOR BEAM OOOO www prolight co uk MODE SETUP uP CEJ 100 240V 50 60HzV POWER OUT 01 Bracket 05 Function buttons 09 PowerCON out socket 02 Bracket tightening knobs 06 DMX input socket 10 Rigging lock Naa AF 03 Earth point 07 DMX output socket 11 Safety bond point Ax user manual 04 LED display 08 PowerCON in socket 12 Fuse 1A 250V 2A 125V www prolight co uk Razor Beam User Manual 4 dj Multiple fixture array _RARA mi 3 T SRR BE E amp lt W DMXIN ARRA me D The LEDJ Razor Beam Bar features guarter turn locks on all sides for linking and aligning multiple fix tures into linear strips or vertical arrays The quarter turn system requires a standard 5 0mm hex key not supplied Note When rigging multiple Razor Beam Bars each bar should be fixed to the trussing with a seperate truss clamp and safety bond Care should be taken to ensure the quarter turn locks are fully located and secure www prolight co uk Razor Beam User Manual 5 Operating instructions DMX channel mode Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to customising or creating a show In this mode you will be able to control each individual trait of the fixture and each fixture independe
4. MODE button www prolight co uk Razor Beam User Manual 9 DMX setup Setting the DMX address The DMX mode enables the use of a universal DMX controller Each fixture requires a start address from 1 511 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 105 and 106 Choose a start address so that the channels used do not overlap E g the next unit in the chain starts at 107 DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing
5. Yu _ Use the UP and DOWN buttons to select the sensitivity 01 being the least sensitive and 31 being the most sensitive Master slave mode To access the master slave mode press MODE until the display shows 51 Aw This ensures the unit is in Slave mode In this mode all the internal programmig is disabled which allows for the unit to follow the standard DMX 512 protocol It may be controlled by abother identical light fixture or by a standard DMX controller Use the UP and DOWN buttons to select the sensitivity 01 being the least sensitive and 31 being the most sensitive Restore factory settings To perform a factory reset make sure the unit is powered off Simultaneously press the MODE and SETUP Whilst holding these buttons power the unit on The unit display will flash r 575 this will restore the unit to its factory settings To exit out of any of the above options press the MODE button Please ensure that all slave units are set to the same DMX channel mode as the master unit www prolight co uk Razor Beam User Manual 8 Operating instructions Product information Press the MODE button until the display shows nF a Now press the SETUP button and then use the UP and DOWN buttons to view the following options When the display shows HE r press the SETUP button to view the product version To exit out of any of the above options press the
6. e are used Termination reduces signal transmission you may need to use a terminator on problems and interference It is always the last unit to avoid erratic behaviour advisable to connect a DMX terminal resistance 120 Ohm 1 4 W between pin 2 Using a cable terminator will decrease DMX and pin 3 DMX of the last fixture the possibilities of erratic behaviour 3 pin Order ref CABL9O 5 pin Order ref CABL89 S pin XLR DMX connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The diagram below details the correct cable conversion F B A E 5 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal 5 pin XLR socket 3 pin XLR socket Pin 1 GND screen Pin 1 GND screen se NX 9 Pin 2 Signal Pin 2 Signal Pin 3 Signal Pin 3 Signal Pin 4 N C Pin 5 N C www prolight co uk Razor Beam User Manual 11 WEEE notice Correct Disposal of this Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries Si with separate collection systems This marking shown on the product or its l
7. fy the unit temperature fluctuation e g after transportation do not connect power or switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors If your product fails to function correctly stop use e Do not expose to flammable sources liquids or gases immediately Pack the unit securely preferably in the e Always disconnect the power from the mains when original packing material and return it to your Pro Light equipment is not in use or before cleaning Only handle dealer for service the power cable by the plug Never pull out the plug by pulling the power cable Repairs servicing and power connection must only be e Make sure that the available voltage is between carried out by a qualified technician THIS UNIT CONTAINS 100 240V 50 60Hz NO USER SERVICEABLE PARTS e Make sure that the power cable is never crimped or WARRANTY One year from date of purchase damaged Check the equipment and the power cable periodically Only use fuses of same type and rating OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation
8. iterature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal CEL www prolight co uk Razor Beam User Manual 12 www prolight co uk Razor Beam User Manual 13 www prolight co uk Razor Beam User Manual 14
9. may lead to danger e g short circuit burns and electric shocks etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and or property www prolight co uk Razor Beam User Manual 2 Product overview amp technical specifications Razor Beam The LEDJ Razor Beam Bar utilises 5 x 9W high power cool white LEDs to produce intense narrow razor sharp beams The LEDJ Razor Beam Bar offers a range of control options including full pixel control via DMX sound active and auto run modes The rugged chassis is built around a single aluminium extrusion which forms the heatsink for the fixture and removes the need for fan cooling also built into the chassis are a series of quarter turn locks allowing the user to align the Razor Beam Bars into linear strips or vertical arrays e 5 x 9W cool white LEDs e Beam angle 3 e 6 2kHz refresh rate e Individually controllable LEDs e DMX channels 3 5 or 9 selectable e Sound active auto and master slave modes plus built in programs e 0 100 dimming and variable strobe 4 push button menu with LED display e PowerCON in out sockets e 3 Pin XLR in out socket e Convection cooled e Quarter turn quick lock alignment system 3 Lux 44700 16500 7560 3900 2540 Specifications Razor Beam Power consumption 53W A A Power supply 100 240V 50 60Hz Dimensions 80 x 400 x 225mm i A EA Na Weight 3 25kg Order code
10. ntly To access the DMX channel mode press the MODE button on the rear of the unit to show d on the LED display Now press the SETUP button twice and the channel mode will be displayed Use the UP and DOWN buttons to choose one of the 3 5 or 9 DMX channel modes Press the SETUP button again the display will now display dO O 1 Use the UP and DOWN buttons to set the DMX channel To exit out of any of the above options press the MODE button 3 channel mode be eee 9 fewer 10 Blackout 20 255 LED strobe active when CH1 value is 20 119 Does not control sound active mode 5 channel mode 000 255 LED 1 0 100 000 255 LED 2 0 100 000 255 LED 4 0 100 000 255 LED 5 0 100 1 o 0 100 www prolight co uk Razor Beam User Manual 6 2 9 channel mode Channel 1 LED 1 0 100 LED 5 0 100 09 No tunetion No function 20 255 LED strobe active when CH7 value is 20 119 Does not control sound active Operating instructions www prolight co uk Razor Beam User Manual 7 Operating instructions Built in program mode To access the built in program mode press the MODE button on the rear of the unit to show Pr _ is displayed the default is Pr U 1 There are 10 available programs each has a unique sentence of lighting fades and chases Use the UP and DOWN buttons to select Pr I through Pr IU Whil
11. st using this program press the SETUP button the display will now show 5P _ Use the UP and DOWN buttons to select any numerical value from OO to 99 to adjust the speed of the program 99 being the fastest To strobe the LEDs press the SETUP button the display will read F5 00 Use the UP and DOWN buttons to adjust the units strobe settings F5 00 is full on F5 01 to F5 99 will adjust the speed of the strobe F5 99 being the fastest Auto run mode To access the auto run mode press MODE until the display shows AL 10 The unit will then automatically sequence through it s ten available programs as described above Static mode To access the static colour mode press MODE until Ur AF shows on the LED display In this mode all five LEDs will be illuminated With the display showing Lr AF press the SETUP button The display will show L _ Use the UP and DOWN buttons to adjust the brightness of the LEDs You are able to adjust this from L U UG off to full brightness 1 055 To strobe the LEDs press the SETUP but ton the display will read F5 00 Use the UP and DOWN buttons to adjust the units strobe settings F5 00 is full on F5 01 to F5 99 will adjust the speed of the strobe F5 99 being the fastest Sound active mode To access the sound active mode press MODE until the display shows Sund Press the SETUP button for the unit to display
Download Pdf Manuals
Related Search