BG90_Instruction and Installation Manual
Contents
1. buttonGeepage 18 control button Air temperature control AN LOW Press HIGH V button e To set air temperature press water pressure air temp O wj button e Air temperature can be set in four 4 different levels and heater OFF e Air temperature can not be set after drying operation is completed Be sure to set the air temperature right after pressing the dryer button Display lamp O ON Heater OFF LOW AIR TEMP gt HIGH Water temperature control Press button e Water temperature can be set in three different levels and water heater OFF Display lamp O ON OFF o o O o O O o Low Med Heater OFF High e Temperature setting is changed each time the button is pressed Seat temperature control Press button e Seat temperature can be set in three different levels and seat heater OFF Display lamp O ON OFF e Temperature setting is changed each time the button is pressed O O O O O O O Low Med Heater OFF High e Feature to prevent low temperature burn This feature automatically lowers the toilet seat temperature with HIGH setting to MEDIUM 10 minutes after the seat was occupied in order to prevent low temperature burn Note eActual seat temperature depends on the ambient temperature Keep the seat cover closed to keep the seat warm and conserve energy thus reducing the electric bill 18 Power saving mode2. cleanser or nylon scrubber when cleaning the Disconnect Failure to do so may cause electric shock or Prohibited power plug injury product Doing so may damage plastic or metallic parts 1 Disconnect the power plug from wall outlet 2 Use a soft and wet with water cloth only when cleaning the unit 3 Clean with a soft and wet with neutral detergent cloth if the unit is very dirty and wipe off the detergent with wet with water cloth Check the detergent type before using the detergent Seat cover may be separated for cleaning 4 Connect the power plug to the wall outlet after cleaning is complete Separation and reassembly of toilet seat cover Seat cover gt ae we Seat cover Separation Reassembly of seat cover Close the cover Insert seat cover to the right side shaft Stretch out right side shaft of seat cover Fit the seat cover into left side of main unit Pull out left side of seat cover Remove the seat cover Note e Do not close toilet seat or seat cover forcibly Doing so may damage the rotation shaft thus preventing easy opening and closing How to take care of this product CAUTION Close water valve before removing the filtering mesh Filtering mesh should be installed securely after cleaning to avoid water leakage Close Failure to do so may cause water leakage Cleaning filtering net Disconnect the power plug from the wall outlet 2 Close the wa
3. deactivated deodorization continues ie i Hitches need to reset the nozzle position as you wish each time you use for about one minute thereafter and stops automatically E A E A E ne i p l e f deodorization button is pressed while more than 15 minutes deodorization is operated deodorization lamp will Deodorization filter is inside the maim unit Water pressure control be OFF operation stops and the setting is cancelled l ying Press tc button to set the water ue bs 2 Med O O O pressure level aov p Press button MedLo O O O e 4 levels may be set w 5 5 a e To stop drying operation press 0 button e Unless reset the pressure level for the last time is aes e Drying operation will stop automatically in five minutes automatically called Low lt Water pressure gt High Press the button again for continued drying operation e The level of water pressure used in cleansing or bidet Display lamp ON OFF e Using dry tissue to remove moisture in user s sensitive product A water pressure level displayed in the product while not in use is the one used in cleansing or bidet cleansing operation for the last time continued 17 Power saving button See page 18 STOP e WASH e BIDET AUTO CARE i TURBO WASH eeMOVE WASH ee MOVE BIDET DRY e AUTO AUTO NOZZLE e POSITION S 7 POWER Se SAVING ee CHILD Warm airtemp Seat temp Water temp Water pump control button control button
4. may lead to water leakage Failure to observe may lead to water leakage See page 20 for cleaning of the filtering mesh Close Do not pull forcibly or apply excessive force to the water feed hose Doing so may cause water to leak Prohibited Select the installation place out of the direct Do not stand on or give a shock to the main sun ray ultraviolet unit Doing so may result in worsening of product surface Doing so may lead to deformation or breakage of the such as discoloration or fading and or product product further resulting in bodily injury degradation Prohibited continued 5 Before use Never use acidic or alkaline bathroom detergent benzene thinner cleanser or nylon scrubber when cleaning the product Doing so may damage plastic or metallic parts Prohibited Keep warm O gt O Z O gt Cc O Z O gt Cc O Z CAUTION for usage CAUTION for usage Do not place or drop the product in into water It may lead to a product failure or electric shock Never place In water Freezing may break pipes and may cause leakage When freezing is highly expected drain the water from the water tank The user of this bidet product should not weigh more than 264 5 lbs 120kg Any person having a female specific disorder skin disorder or disease in the sensitive private area should consult a physician before
5. using this product This product is not medical equipment Water pressure setting should be positioned to Low or Very Low when the product is used by a person having sensitive skin or a disease in the sensitive private area the elderly the invalid or the disabled Failure to do so may lead to damage to skin Please use the genuine water filter only We will not take any responsibility for the problems resulting from the use of other filters In the event that the product is reinstalled at different location due to movement or relocation of bidet product close water valve disconnect power plug from electrical outlet and completely drain and remove water from the main unit before packaging the product for movement e f the product is moved with some water inside the main unit water leakage from water tank may cause electric shock fire or product failure e Please refer to page 28 of this manual concerning how to remove water from the main unit e Please contact the dealer or retailer where the product was purchased for further information Operational Instructions Water supply to the toilet water tank may be interrupted if the ball tap connecting screw is tightened when disassembling the water pipe or connecting water feed hose Do not touch ball tap connecting screw Have a specialized plumber install the hot water feed pipe and the flush valve in the cold area Contact specialized technician Keep the
6. Press button e Pressing the button once will set Lo Econo Pressing the button the second time will set Hi Econo Pressing the button the third time will cancel the power saving mode Lo Econo e When the product is not in use water temperature 77 F 25C and seat temperature 82 4 F 28 C are set respectively regardless of the settings Electric power is saved through a shorter application time of electric current unless water temperature and seat temperature are set to OFF e When cleansing bidet cleansing auto child cleansing turbo cleansing or drying is operated water temperature and seat temperature are raised to the set temperature by applying electricity It takes about five 5 minutes to get to the set temperatures e When cleansing bidet cleansing auto child cleansing turbo cleansing or drying stops water temperature and seat temperature are again set to 77F 25C and 82 4 F 28 C respectively regardless of the settings Hi Econo e When the product is not in use electric power is cut off to water heater and seat heater regardless of the settings Lo Me Hi e When cleansing bidet cleansing auto child cleansing turbo cleansing or drying is operated water temperature and seat temperature are raised to the set temperature by applying electricity It takes about 5 minutes to get to the set temperatures All the lamps other than Econo lamp are turned on e When cleansing bidet cleansing auto child cle
7. UTO ee CHILD AUTO CARE x POWER POWER SAVE DEODORIZATION Fao AN HIGH WATER PRESSURE DRY TEMP LOW FRONT NOZZLE TEMP POSITION CONTROL NOZZLE WATER REAR Auto Child cleansing button Seat temperature control button Water pump button i Nozzle cleaning button Feminine cleansing button Posterior cleansing button Water pressure warm air temperature control button Accessories Items required for installation LI Mounting bolt Hemisphere packing Brush for cleaning 1pc Mounting plate 2pcs Washer Y Nut ry i Water filter 1pc Water tank hose Water feed hose Mounting plate 13 7in 0 35m 1pc 19 6in 0 5m 1pc T connector 1pc guide 1pcs includes packing includes packing Packing 1pc Mounting bolt set 1 set Deodorization button Before use Installation Instruction Close water valve Check if any appliance is used with water before closing the valve Close the valve by turning the handle or using a screwdriver Note Check any nearby tap water if water dose not run after the valve is closed 2 Remove the existing toilet seat Remove the seat by untightening the nut using a tool Note Keep the removed seat seat cover nuts etc in the safe place for future use just in case 3 Attach T connector valve WE Standard water valve inner screw type water valve 1 Connect
8. Wait at least 5 to 7 minutes after the cleansing function is used by a different user to make tank water warm e Cancel the power saving mode Water in tank gets warm e Press power button e Set the seat temperature to Med or Hi e Wait about 5 minutes after occupying the seat to make the seat warm e Press power button e Tighten the screw e Check the main unit installation and correct the problem if any e f this happens regardless of season contact authorized service center e Set the temperature to Med or Hi e Press dryer button again specifications Model BG93 Power Source AC 120V 60Hz 650W 10 15 108 77 psi 0 07 0 75MPa Approx 41 F 95 F 5C 35C 0 13 0 18gal min 0 5 0 7L 0 13 0 18gal min 0 5 0 7L Rated Power Consumption Effective Tap Water Pressure Range Effective Tap Water Temperature Range Posterior Cleansing gal min Feminine Cleansing gal min Water Pressure Control Low Med Low 4 Phases each for Posterior Feminine Cleansing ediumHigh 3 Phases Appox 91 4 F 104 F 33C 40 of control and Heater off 6 Positions for each of Posterior and Feminine Cleansing 600W Water Tank Capacity Approx 0 17gal 0 67L Safety Device Temperature Control Nozzle Location Control Water Heater 99149 BHulsuee 9 Jaye WEM Thermo s wlprevention of overheating Temperature fuse Water level sensor eo Temperature Control 3 Phases Appox 91 4 F 102 2 F 330 39C of control and H
9. When the product is aged over time screw bolt may get loose In such case tighten the nut again The distance between the bolts can be adjusted in the range from 5 1 inch 130mm to 7 8 inch 200mm depending on the hole locations on the toilet bowl CAUTION Carefully align the center of main unit to that of toilet bowl when attaching and fixing the main unit Use the wrench enclosed with bidet when tightening Water tank Water feed hose T connector Mounting plate Mounting bolt guide AT KI z W B Mounting plate guide Installation Hemisphere packing Washer B Nut continued 11 12 Installation Instruction 4 Align the center of main unit to the center of the plate guide and push all the way until click sounds 5 Check if or not the main unit easily comes off by moving the unit in four different directions When the main unit is installed to toilet bowl it may be a little movable which does not indicate abnormality This happens as the main unit removable type Note The main unit may become heavily movable if used over an extended period of time due to loose bolts Fully tighten the bolt if that happens Grounding Instructions This product should be grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing an escape wire for the electric cur
10. aned with tooth brush etc clockwise the stainless part with the hole facing downward Note Check if the stainless part may not come off easily Note check if the stainless part may not come off easily 7 Put the cleaned nozzle tip back to nozzle body while holding the nozzle body Nozzle body Nozzle tip Note e Do not damage the nozzle hole e Do not apply excessive force to nozzle e Do not separate and clean the nozzle too often Doing so may cause a problem e Cleansing nozzle tip is assembled a little tightly to secure air tightness e Be careful so that no bodily injury may occur when separating the nozzle tip for cleaning Press 0 button on the main unit control panel e Nozzle retracts only when a button is pressed after cleaning is done Note e There may be a strange sound when nozzle retracts which does not indicate product failure Put back the nozzle cleaning cover and close toilet seat and cover slowly 24 How to prevent freezing and to care for the product when it is not in use over an extended period of time Remove moisture around the water feed system as freezing may lead to a breakage of the system Remove moisture when the product is not in use for an extended period of time Water may become spoiled causing skin irritation Prevention of freezing and long term care for product I 2 Unplug the power plug e Disconnect the plug from the wall outlet Close water valv
11. ansing turbo cleansing or drying stops electric power to water heater and seat heater is cut off again Other tips for saving electric power Refer to the following methods for power saving Keep seat cover closed Setting a lower temperature Unplug the power plug when the product is not As long as you do not feel cold Disconnect the power plug to in use set a lower temperature whenever reduce power consumption when possible It will somehow the product is not used over an Keeping seat cover closed will l Pma contribute to power saving extended period of time help reduce electric power consumption as the heat radiation from the surface of toilet seat is significantly decreased Water pump Press button e When pump lamp is ON pump will operate to increase water pressure during cleansing bidet cleansing auto child cleansing and turbo cleansing If the pressure level is too high adjust the level using water pressure control button e When pump lamp is OFF pump will not operate Initially the product is set to pump OFF e f the pressure reaches 14 2 psi 1 0 Kgf cm the pressure level will remain the same even if pump operates e f the pressure is too high stop pump operation as it may lead to injury 19 20 How to take care of this product WARNING CAUTION Disconnect the power plug while Never use acidic or alkaline toilet cleaning the product detergent benzene thinner
12. ar children or invalids Use this product only for its intended use as described in this manual Do not use attachments not recommended by the manufacturer Never operate this product if it has a damaged cord or plug if it is not working properly if it has been dropped or damaged or dropped into water Return the product to a service center for examination and repair 5 Keep the cord away from heated surfaces 6 Never block the air openings of the product or place it on a soft surface such as a bed or couch where the air openings may be blocked Keep the air openings free of lint hair and the like 7 Never use while sleeping or drowsy 8 Never drop or insert any object into any opening or hose 9 Do not use outdoors or operate where aerosol spray products are being used or where oxygen is being administrered 10 Connect this product to a properly grounded outlet only See Grounding Instruction 11 Unplug this product before filling Fill reservoir with water only unless otherwise specified by manufacturer Do not overfill or specify filling instructions SAVE THESE INSTRUCTIONS MEMO MEMO
13. ck if nozzle extends and discharges warm water Cover up the nozzle to prevent water from spraying outside 7 After confirming that warm water is coming from the nozzle press stop button or separate the palms from the sitting sensor so that the operation may be stopped Cleansing operation stops and nozzle retracts How to use basic features WARNING Set the Seat Temp Control Button to Off or Low if the product is used by the following person Young children the aged or users incapable of adequately setting the temperature People with sensitive skin and or skin irritation People having taken sleep inducing medicine such as sleeping pill or cold medicine CAUTION People suffering from hangover or severe physical fatigue Failure to do so may lead to the low temperature burn or injury STOP WASH e BIDET AUTO CARE ers TURBO WASH eeMOVE WASH ee MOVE BIDET DRY e AUTO lt POWER FRONT SAVING Q AUTO e A NOZZLE A TEMP POWER SAVE DEODORIZATION oe POSITION Te CONTROL 2 REAR WATER PUMP ee CHILD gt Stop button Feminine Oscillating Feminine cleansing button Posterior Oscillating cleansing button Sit on the seat 2 Press OF A putton Note e Nozzle cleaning starts when Cleansing or Bidet button is pressed e Nozzle position can be adjusted as desired when Nozzle position control button is used e The continuous operation of Cleansing or Bidet function will depl
14. e e Use the blade type screwdriver to close the water feed valve lf the valve is manual type use hands to close the valve Drain warm water tank e Drain water from water tank after rotating and removing the drain plug while lifting and holding the main unit by using the main unit mounting button Prepare and use a container of which capacity is not less than 0 52 gallon 2 liters to keep the drained water e Put the drain plug back after draining water completely from the tank gt eS x Use coin when and if the water tank cap oS is not opened easily O Drain water from inside water feed hose e Disconnect the water feed hose from the water feed inlet of main unit and place the end of the hose in a container for holding water a aa Tvar feed hose Container with wider mouth How to cancel the freezing prevention arrangement and to start to use the product again IT Put the drain plug back to the water tank 2 Connect the water feed hose as is the original condition Refer to installation instruction e Make sure and check before connecting the hose that there is a packing in hose joint 3 Open the water feed valve 4 Connect the power plug to the wall outlet e Press Cleansing button to fill the tank with water Flickering Warning Lamps Display Bec Trouble in water temperature 2O g 9 e Inability to control warm water O7 temperature due to failure of water tem
15. eater off Ta Toilet Seat Heater 47W Safety Device Temperature fuse z Temperature Control 4 Phases Appox 95 F 131F 35 C 55C of control and Heater off z Dryer Heater 290W 2 Air Velocity Approx 0 009mi s 15m s O Safety Device Temperature fuse Bimetal Deodorization O Water Filter O Water Pressure Pump O sounyea4 HOJA Power Saving Mode Lo Econo Hi Econo Built in Circuit Breaker 19 1in Width x 21 4in 19 8in Length x 6 0in Height 487mm Width x 545mm 505mm Length x 154mm Height Approx 10 5lb 4 8kg Approx 39 3in 1 0m Additional safety Devices Exterior Dimension Net Weight Length of Power Cord 28 Important Safeguards When using electrical products especially when children arre present basic safety precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING DANGER To reduce the risk of electrocution 1 2 3 4 5 Always unplug this product immediately after using Do not use while bathing Do not place or store product where it can fall or be pulled into a tub or sink Do not place in or drop into water or other liquid Do not reach for a product that has fallen into water Unplug immediately WARNING To reduce the risk of burns electrocution fire or injury to persons de 2 3 A product should never be left unattended when plugged in Close supervision is necessary when this product is used by on or ne
16. ete the supply of warm cleansing water dropping the water temperature Therefore it is recommended that Cleansing or Bidet function be stopped and used again only after the cleansing water gets warm e Water temperature and or seat temperature may be adjusted while cleansing or bidet cleansing is used e Do not apply excessive force when pressing a button Doing so may make the button inoperable Oscillating cleansing Oscillating bidet cleansing 3 Press or R button one more time while cleansing or bidet cleansing is operated so that oscillating function may be activated e Nozzle moves back and forth to provide cleansing of wider area e Press Cleansing or Bidet button one more time to deactivate the oscillating function 4 Press 0 button to stop cleansing operation Note e Continued use of cleansing for more than 90 seconds will activate the timer thus stopping the cleansing operation automatically For continued operation press Cleansing button again e Cleansing lamp or bidet lamp will be turned out Nozzle moves back and forth three times around the nozzle inlet for self cleaning e During about six 6 seconds of the nozzle cleaning cleansing or bidet cleansing may not be selected Stand up Note e Water coming out of nozzle right after cleansing operation does not indicate a product failure It stops fr mMm th automatically in about two minutes after the remaining water in the hose is completely released 0 e S
17. il 1 Open water valve 2 Open water feed valve and check if water leaks from any pipe joints If water leaks 1 Close water valve 2 Disassemble the joint where water is leaking and connect properly again Note e f water continues leaking close water valve and contact a nearest authorized service center Operational Check Check the operation of the product in the following order 1 Open water valve Applicable only when closed 2 Open water feed valve with a blade type screwdriver Use hands for handle type Check if water leaks from pipe water tank hose or water feed hose joints lf water leaks close the water feed valve separate the valve and check if rubber packing is inserted If not insert the packing and reassemble the water feed valve 3 Connect the power plug to the wall outlet Nozzle extends and retracts once and the control panel lamps keep blinking at initial operation 4 Press button on the control panel Water pressure Dry Air lamp goes off when the tank is full of water and Seat Temperature Water Temperature and Water Pressure are set to Low respectively Wait until cleansing water gets warm It takes about 5 minutes Check if the seat gets warm too 5 Approach hands to sitting sensor within 1 9 inch 5 cm so that it may be activated 6 If the tank is full of water press button one more time and check if the posterior cleansing is correctly operated Che
18. inute of oscillating cleansing followed by two e Warm water is sprayed for one minute with water pressure set to Hi e Water temperature and toilet seat minutes of drying and stops You may reset the level of pressure during the turbo cleansing operation temperature saved respectively in the e During the child cleansing operation water pressure is elf you are ready for bowel movement press 0 button to stop the turbo operation MAN nae CAINEA orally set to Lo and temperatures of water seat and drying e Massaging effect is produced while air are set to Med automatically a water pressure level changes automatically Nozzle position control Deodorization Press a L button while cleansing or bidet cleansing is operated Tad N l Press H button C H B e Initially nozzle is positioned in center location and it moves in three steps forward Operation and three steps backward during cleansing or bidet cleansing Deedorization lamecwil be ON and deodorzation wil Start e Each time is pressed deodorization is activated and Display lamp G ON OFF Note deactivated and the process will continue AA e Nozzle position used for the last time is not automatically saved in the product e When the seat is occupied and sitting sensor is Note Aa unit eee returns Pa position center once cleansing or bidet activated deodorization will start ar eer eee pee oe eee eer ree Geese OPel ation gt compete i e When sitting sensor is
19. mall amount of water running out of nozzle from time to time does not indicate a product failure or seat abnormality This occurs because of the expansion of water that gets warm in the water tank e f the water runs continuously in an unusual manner contact nearest authorized service center after closing the water valve and disconnecting the power plug from the wall outlet Operation continued 15 How to use additional features How to use additional features AUTO CARE ore WASH e BIDET STOP STOP e WASH BIDET AUTO CARE ae h N EE NT E A e Ae TURBO WASH eeMOVEWASH ee MOVE BIDET e AUTO lt te FRONT HIGH 0 B S FRONT SAVING SH e CHILD Pe Seis gt PUMP Turbo cleansing button Nozzle position Water pressure Drying button Auto child cleansing button Deodorization button control button control button Turbo cleansing Auto child cleansing auto For Auto Cleansing operation For Child Cleansing operation A AUTO Upon sitting on the toilet seat press 0 button in advance press button only once press button twice l l m l e One minute and 20 seconds of oscillating e The button needs to be pressed twice at an interval e Warm cleansing water is sprayed and touches the skin as if it produces a massaging effect while cleansing followed by two minutes of not exceeding three seconds Heme ahs PACK ANG TONA l a drying and stops e One m
20. not use the product for other usage than described in this user manual Failure to do so may lead to fire electric shock or injury 9 5 Prohibited Do not put stove heater or cigarettes nearby the product Doing so may lead to fire discoloration or malfunctioning Prohibited Grab the plug knob for unplugging the power plug Failure to do so may result in electric shock electric short circuit or fire Disconnect power plug Do not rest against the seat cover when sitting on the seat This may cause the seat cover to break which may further lead to the back injury if the user loses his her balance and tumbles over Prohibited Do not insert fingers into or block off the warm air blower outlet Doing so may result in burn or injury Do not insert fingers or other objects into warm air outlet or nozzle gate nor spray water Doing so may lead to electric shock or product mal functioning Prohibited Prohibited Do not let a child alone use this product He she may Always press the control panel button while fall into the toilet bowl the seat is occupied The child needs to be attended by an adult Otherwise the person standing by the product or the floor may get wet due to warm water coming out of nozzle CAUTION CAUTION Shut off the water valve before removing the filtering mesh for cleaning Make sure to fasten it up after the cleaning Failure to observe
21. novita BG90 BG93 Instruction and Installation Manual Table of Contents 3 Safety Instructions 2 6 Operational Instructions 7 2 Name of components 8 9 __ Accessories g Installation Instructions 10 12 O Grounding Instructions 13 5 Cc Things to be checked after installation 14 How to Use Basic Features 15 How to Use Additional Features 16 19 How to take care of this Product 20 23 Prevention of Freezing 24 25 Flickering Warning Signals 25 Troubleshooting 26 Specification 27 Important Safeguards 28 safety instru ctions Be sure to observe the following e Be sure to read the following safety instructions carefully and use the product only as instructed in this manual to prevent bodily injuries and or property damage which might happen while using this product e Thoroughly understand each of the following symbols marks and graphical signs read all instructions and precautions and follow them Never use a damaged power cord damaged Power plug should be plugged into the wall Eels fo E nnnOr inc eer aa eee T power plug or a loose electrical outlet outlet securely AN WARNING following might result in AN CAUTION following might A in minor Doing so may result in fire electric shock short circuit Failure to do so may result in electric short circuit critical injury or death injury and or product damage smoke generation or ignition electric shock smoke generation or ignition Ta S Strictly prohibi
22. onsumer mistakes and or misuse and abuse of the product or the use of the product under abnormal condition Manufacturer takes no responsibility for any incidental damages resulting from the use of the product or inability to use the product lost profits or suspension of business etc Manufacturer takes no responsibility for any damages resulting from the failure to observe the contents contained in this manual Drain water Prohibited When a child the elderly or the invalid uses the Do not scratch crack bend forcibly twist or pull the Use tap water or portable water only P Do not spray water or wastewater into the unit or Using recycled water or industrial water may cause cystitis or power plug product the seat temperature adjustment button electrical power cord Do not apply heat to or place should be set to OFF position heavy objects on the cord T the elderly people S sensitive oen B of Damaged power cord may lead to fire or electrical shock Do not E er a E E tae attempt to replace a damaged power cord on your own Contact a inducing medicine sleeping pill or cold j medicine etc or people with hangover nearest authorized service center for replacement or severe weariness may sustain low S Use tap water irritation to skin Doing so may cause fire or electric shock Prohibited temperature burn or injury O F F W for kids the elderly etc Prohibite CAUTION Keep the po
23. perature sensor e Trouble in seat temperature e Inability to control seat temperature due to failure of Das seat temperature sensor No water or water shortage in tank All lamps are blinking Inability to control water level due to malfunctioning water level sensor Display lamp O ON OFF Estimated cause and action to be taken Stop using the product and contact a nearest authorized service center for repair service Disconnect the plug and reconnect Then press cleansing button to fill tank with water If the lamps still flicker then disconnect the plug and contact authorized service center Care amp Cleaning Before you call for service NO O1 26 Before making a call for service essees Product not working Cleansing water not coming Water pressure too weak Cleansing water sufficiently warm Seat not sufficiently warm Main unit does not sit on the toilet bowl securely Seat or seat cover is not closed smoothly and gently Air temperature too low Drying stops during operation Cause e Check power outage Check if circuit breaker operated e Check if the plug is plugged in e Check if power is cut off by the use of power button e Check water supply e Check if water feed valve is closed e Check if water feed hose is frozen e Check if all lamps are blinking e Check any foreign material in filtering mesh e Check if water feed hose is fo
24. rcibly bent e Check if nozzle opening is clogged e Check if water pressure is set to Lo e Check if tap water pressure is less than 10 1 psi 0 07MPa e Check if water temperature is set to OFF or Lo e Check if cleansing is used continuously e Check if Econo mode is set e Check if power is cut off By the use of power button e Check if seat temperature is set to OFF or Lo e Check if Econo mode is set e Check if power is cut off by the use of power button e Check if mounting bolt is tightened securely e This happens when ambient temperature is high or when the product becomes aged over time e Check if air temperature is set to Lo e Check if five or more minutes have passed since the dryer button was pressed Time required for water to get warm depends on ambient temperature How to handle e Wait for power restoration e Disconnect the plug and reconnect e Connect the plug e Press power button if power is cut off e Wait for water back to service e Open water feed valve e Make the frozen part warm using hot and wet cloth or make the room warmer to unfreeze Do not unfreeze using hot water or hot air It may cause a breakage of the hose e Contact authorized service center e Clean the mesh e Straighten the hose e Clean the nozzle opening e Set the pressure to Hi e Water pressure should be between 10 1 108 7 psi 0 07 0 75MPa e Set the temperature to Med or Hi e
25. rent This product is equipped with a cord having a grounding wire with a grounding plug The plug must be plugged into an outlet that is properly installed and grounded DANGER Improper use of the grounding plug can result in a risk of electric shock If repair or replacement of the cord or plug is necessary do not connect the grounding wire to either flat blade terminal The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire Check with a qualified electrician or serviceman if the grounding instructions are not completely understood or if in doubt as to whether the product is properly grounded If it is necessary to use an extension cord use only a three wire extension cord that has a three blade grounding plug and a three slot receptacle that will accept the plug on the product Replace or repair a damaged cord GROUNDED OUTLET S GROUNDED HY OUTLET BOX GROUNDING PIN Installation 13 Things io be checked after installation Check for water leakage Check the water leakage from any of the pipe connection after installation gt Inspection areas Inspection points e Check if packing was all used in the installation If there is any packing left check where it is missing disassemble the joint where it is missing and properly use it e Check if there is any loose connection or joint before feeding water il Erron EEA EEA ott S
26. s the button again if you wish to further use Keep clean the nozzle and warm air blower outlet against the possible stain from urine by a male user It may cause malfunction When the product is operated while toilet seat is not occupied as in the following cases be careful as water may splash e When a child intentionally press a button e When a button is pressed during cleaning e When an object is placed on the control panel Deodorization will stop automatically after 15 minutes of continuous use Please stand up and sit again for longer use The main purpose of deodorization is to remove the odor in toilet bowl It s not for the whole bathroom Before use Name of componenis _ A The number in the mark indicate the number of pages where the terms shall appear Front side of main unit a Seat cover Main unit T connector Sitting sensor N Nozzle Water feed hose ae SS 9 11Page 7 Control panel 9 14 18Page Toilet seat heated toilet seat Rear side of main unit Water inlet NN Warm water tank drain Warm air blower outlet deodorization Mounting demounting button deodorization Control Panel Control panel layout may vary depending on the models Power saving button i Warm water Nozzle position temperature control button control button Stop Turbo button Drying button STOP e WASH e BIDET TURB WASH eeMOVE WASH ee MOVE BIDET DRY e A
27. ted Z Be sure to unplug the electric power plug Never disassemble or modify this I S Do not place in or drop into water product l Prohibited Proper grounding required to Q e e alied lt Things that have to be observed Insert securely Disconnect the power plug from the wall outlet and Do not water the product Do not install the product in 1 Serious injury includes loss of eyesight severe wound burn high low temperature electric shock bone fracture poisoning etc leaving drain water from water tank in the case that the wet or damp places This product is intended for use aftereffect and requiring hospitalization or regular hospital visit for a long time for recovery i 2 Injury means minor wound burn or electric shock that does not require hospitalization or regular hospital visit for a long time for recovery product is not used over an in toilet only and should not be used for any other 3 Property damage refers to extensive damage relating to house furniture livestock or pet etc extended period of time purpose Exemption from liability If not drained the water may Failure to observe may lead to be contaminated electric shock electric short circuit Manufacturer takes no responsibility for any damages resulting from natural disasters such as earthquakes lightening and wind damage and flooding fires not caused by the manufacturer or the bidet product covered by this manual other accidents c
28. ter feed valve using a blade type screwdriver Use hands if the water feed valve is manual type 3 Separate the water feed hose from the main unit e Be careful so that the floor does not get wet due to water remaining inside the hose 4 Clean inside the filtering mesh using toothbrush etc e The filtering mesh is built in the water feed inlet of main unit 5 Connect the water feed hose to the main unit and open the water feed valve e Check if or not water leaks Connect the power plug to the wall outlet Connect the power plug to wall outlet Open seat cover and toilet seat 3 Press nozzle cleaning button on the main unit control button e Nozzle moves back and forth 3 times for self cleaning and stops moving under fully extended condition Clean the nozzle while it is fully extended 1 Separate the nozzle cleaning cover 2 Put inside soft sponge brush cloth or toothbrush that gets wet with water and clean Note Be careful so that water may not get into warm air outlet Note Be careful so that water may not get into warm air outlet 3 Pull nozzle tip from nozzle body while holding the nozzle body and separate the tip 4 Using a tool inside the separated tip push bidet nozzle so that it may be cleaned with soft sponge brush or cloth 22 5 Rotate the stainless part of nozzle body counterclockwise and separate the stainless so that it may be cle
29. the T connector to the toilet water tank Over tightening by using excessive force may caution lead to a breakage 2 Connect the T connector and the water valve with the water tank ee hose Pa H 1 Water leakage may occur if the packing is A w CAUTION not used when connecting WT TI Hold the T connector valve firmly when j R connecting the hose so that the T connector Packing NZ valve does not rotate Water valve gt 3 Connect the water filter to the T connector Make sure and check before connecting the hose that there is a packing in hose joint Connect the water feed hose to T connector which is connected with the water valve Water tank Packing for water tank hose Water tank hose 4 Connect the water feed hose to the water filter Make sure and check before connecting the hose that there is a packing in hose joint 10 Installation Instruction 4 Connect the water feed hose Connect the water feed hose to the main unit Check if there is the packing in the hose connection before connecting 5 Install the main unit 1 Remove hemisphere packing washer and nut from mounting bolt and insert the mounting bolt to the mounting plate 2 The head of mounting bolt should come in direct contact with the mounting plate 3 Insert mounting bolts to the toilet bowl holes while aligning the bolts to the holes and connect hemisphere packing washer and nut in such order Note
30. unused water pipes for future use Do not open close the toilet seat and cover using excessive force Doing so may lead to breakage or malfunction Water may keep running out of nozzle after cleansing It does not indicate abnormality It is residual water from the inside pipes It will stop after 2 minutes Drain water completely out of warm water tank to prevent possible water leakage and unplug the power cord when the product is not in use for a long time Wipe up the main unit with a soft cloth when it s dirty Clean with a diluted neutral detergent using soft cloth and then wipe off with the remaining with damp cloth if it is excessively dirty Keep clean the nozzle against the contamination It may cause bad odor or malfunction Small amount of water may run out of nozzle occasionally It does not indicate abnormality This occurs due to the expansion of water that gets warm in the water tank If water runs continuously in an unusual manner shut off the valve unplug the power cord and call the service centre or the dealer No cleansing water will be supplied from nozzle if water pressure control is set to low in the area of low tap water pressure Please set the water pressure control to high Do not press the buttons on the control panel too hard when operating the product Doing so may lead to a failure Cleansing will stop automatically by the timer after about 90 seconds of use Pres
31. wer plug dust free by removing the dust When plugging and unplugging the power plug never Use electric wall outlet independently which is Never disassemble repair or modify the using a dry cloth use wet hands suitable for AC 120V rating over 7 Ampere product Failure to do so may cause a fire Doing so may lead to electric shock Use of extension cord or sharing an outlet with other Doing so may cause fire electrical shock or injury product may lead to fire of electric shock Contact a nearest authorized service center for repair ZH Y Wet hands prohibited Disassembly Prohibited continued 3 Before use When cleaning the product always disconnect the power plug from the wall outlet Failure to do so may result in electric shock Discontinue using the product in case of malfunctioning Disconnect the power plug from the electrical outlet and close the water valve if any of the following occurs e Water leaks from either the main unit or the water pipe or injury e The product makes odd noise or produces unpleasant odor e Abnormal heat from the main body e Fuming from main body Continuing use of a malfunctioning product as mentioned above may lead to fire electric shock or water leakage Please contact the dealer or an authorized service centre for repair Disconnect power plug safety Precaution Disconnect power plug e Crack or break on main body N CAUTION Please do
Download Pdf Manuals
Related Search