manual - Ring Automotive
Contents
1. user The E Can contains no user serviceable parts Do not open Power Supply The battery or power supply must provide between 10 5 and 14 5 Volts DC a car battery will usually provide this and must be able to provide sufficient current to operate the load the item you require to power The power supply used may be a battery or a regulated DC power supply In order to find out if your power supply is large enough divide the power consumption of the load in watts by the voltage 12v in the case of the E Can inverter this will give you the current in amps that the power supply must deliver EXAMPLE Load is rated at 48W 12v 4 Amps Connecting to your power supply Connect the DC plug on the E Can inverter to the vehicle battery by plugging directly into the 12v DC socket cigarette lighter socket The LED power monitor illuminates green when power is on The E Can must only be used on vehicles where the centre contact of the cigarette lighter socket holder is positive Ensure the load requirements are within the specification max 120w of the E Can output Plug your appliance into the socket of the E Can inverter Positioning of the E Can inverter The following points should be noted CAUTION The E Can inverter is not waterproof Take care if adjacent drinks holders contain or have contained liquids The E Can should be used in a ventilated area Do not obstruct the vent at the rear of the E Can Do not put t2. RIND Power POWERING Seam Can Inverter Troubleshooting guide PROBLEM Low output voltage Possible Cause E Can inverter is overloaded Unsure about the appliance rating Suggested Remedy Reduce load not exceeding E Can maximum rating Consider upgrade RINV300 to 3000 Check the data label on the appliance or the instructions If this is unsuccessful consult the manufacturer PROBLEM Re occurring low battery shutdown Possible Cause Inadequate power or excessive voltage drop Poor battery condition PROBLEM No power output Possible Cause E Can inverter in thermal shut down condition Low battery voltage E Can inverter blown fuse Vehicle blown fuse DC socket Poor DC plug connection Suggested Remedy Check connections from battery to E Can inverter Replace or charge battery Suggested Remedy Remove power and load allow to cool 10 minutes Charge or replace battery Check replace the 15Amp fuse in the DC plug Check vehicle handbook to locate relevant fuse Use the DC plug switch to ensure a good connection PROBLEM Liquid ingress Possible Cause Drinks spillage Suggested Remedy Unplug the E Can and wipe immediately with a dry cloth Permanent damage can occur with liquid ingress SPECIFICATIONS PowerSource Model E Can Part Number RINVC120 Max Continuous power Watts 120w 5 mins 100w 4 hours Peak Power Watts 0 01 Seconds 200
3. he E Can on or near sources of direct heat or expose to direct sunlight Do not operate the E Can in or around flammable environments Ensure cables and leads connected to the E Can do not interfere in the safe operation of the vehicle e When not in use store securely in a cool dry dust free environment Do not leave connected to 12v DC socket unattended Remove from 12v DC socket when not in use as the unit will continue to draw 0 3 Amps stand by current Do not operate continuously for more than 4 hours Do not use the power lead to move or carry the E Can Operating Tips NOTE The PowerSource is not designed to run products that provide heat such as hair dryers heaters and irons Do not handle the E Can inverter with wet hands or if it has come into contact with liquid e Ensure while driving all accessories powered by the E Can inverter are positioned securely Do not use distracting accessories such as mobile phones whilst driving To ensure optimum performance from the E Can adjust the DC plug switch for the correct fit in the vehicles DC socket Maintenance Cleaning Only clean the E Can inverter using a clean dry cloth Do not use cleaning products Fuse Replacement The fuse is located in the E Can DC plug Unscrew the end of the DC plug and extract the 15 Amp fuse Check the fuse and replace if necessary with an equivalent 15 Amp fuse Protective features Auto shutdown The E Can inver
4. ter will automatically shut down if the supply voltage is less than 10v At this point the green LED will go out The inverter will automatically restart when the input voltage is above 10v Overload protection The E Can inverter will automatically shut down if the continuous power draw exceeds the maximum rating Short circuit protection via automatic thermal resetting fuse Temperature Protection If the temperature of the internal heat sink reaches gt 65 C the E Can will shut down automatically Remove from power and allow to reset when cool before using
5. w Standby current Amps lt 0 3A Waveform Modified Sine Wave Efficiency 90 Input Voltage Range 10v 15v DC AC Socket 3 Pin mains 230v AC Product Dimensions mm D x H 66 x 160 Pack Dimensions mm L x W x H 150 x 100 x 210 Cable length mm 450 Percentage of battery power to mains voltage power C and approved This inverter should only be used to power Class II non earthed products identified by the symbol O RING Distributed by Ring Automotive Limited Volvox House Gelderd Road Leeds England LS12 6NA Automotive G 44 0 113 213 2000 44 0 113 231 0266 autosales ringautomotive co uk www ringautomotive co uk Portable Power POWERING Seen Can Inverter 12v DC to 230v AC Mains Inverter RINVC120 User Manual www ringautomotive co uk RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE Ox __ Power POWERING Seam Can Inverter Introduction The Ring E Can inverter is an electronic device that converts a low voltage 12v DC current from a battery or other power supply and provides 230v AC current Special attention should be made to CAUTION statements in this user manual CAUTION statements identify conditions or practices that could result in damage to your E Can or to the equipment you are using with it CAUTION Do not exceed the maximum input voltage 15 Volts DC Improper use of the E Can inverter can cause damage to property and possibly harm to the
Download Pdf Manuals
Related Search