LED MOVING HEAD 144W WASH 4in1 RGBW - Flash
Contents
1. 4 2 Menu map RPON address code setting from A001 A512 AUO1 auto moving speediness AUO2 slow speed auto moving SNO01 Sound control for color changing SNO2 Sound control for strobe RPOF Set pan to forward rotating RPON Set pan circumrotate reverse RTOF Set tilt to forward rotating RTON Set tilt circumrotate reverse RDOF set the LED readout to non inverting RDON Set the LED readout to inverting DFON Default output setting Note output default setting address code is A001 pan is positive circumrotate tilt is positive circumrotate LED positively reveal 4 3 User configurations Setup single desk light s autocephaly moving mode auto running Press the MENU until it shows AUO1 Use the UP DOWN buttons to set to AUO1 or AUO2 Press ENTER to confirm Setup single desk light s autocephaly moving mode sound control Press the MENU button until it shows SNOF Use the UP DOWN buttons to set to SNOF press ENTER to confirm Master slave mode auto running sound control This mode will allow you to link up 32 units together without a controller Use standard DMX cables to daisy chain your units together via the DMX connector on the rear of the units Proper performance it may be necessary to use a terminator at the last fixture For more information about terminators Set the desired master mode Automatic program mode or sound controlled mode for the master device send the DMX address 1 for all slave dev2. F 40 C Date input output Product size N W Packing size G W 1pc 3pin XLR connection anlde socket 260 x260x350mm LxW xH 5 7kg 645 X 360 x 405mm L xX W x H 2pcs package 6 6kg
3. Save the carton and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture be returned in the original factory box and packing 1 3 AC Power To determin the power requirements for a particular fixture see the label affixed to the back plate of the fixture or refer to the fixtures specifications chart A fixture listed current rating is its average current draw under normal conditions All fixtures must be directly powered off a switched circuit and cannot be run off a rheostat variable resisto or dimmer circuit even if the rheostat or dimmer source voltage matches the fixtures requirement Check the fixture or device carefully to make sure that if a voltage selection switch exists that it sets to the correct line voltage you will use Warning Verify that the voltage select switch on your unit matches the line voltage applied Damage to your fixture may result if the line voltage applied does not match the voltage indicated on the voltage selector switch All fixtures must be connected to circuits with a suitable Earth ground 1 4 Safety instructions Pleese read these instructions cy it includes important information about the installation usage and maintenance of this product Please keep this user guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Always make sure that you are connecting to the prope
4. LED MOVING HEAD 144W WASH 4in1 RGBW User Manual www flash butrym pl Page 1 Table of contents 1 Preface 1 1 Packing list 1 2 Unpacking instructions 1 3 AC Power 1 4 Safety instructions 2 Introduction 2 1 Features 2 2 DMX channel 3 Setup 3 1 Fuse replacement 3 2 Fixture linking Data cabling DMX data cable 3 3 3 Pin to 5 Pin conversion chart 3 4 Setting up a DMX serial data link 3 5 Master Slave fixture linking 3 6 orientation 4 Operating instructions 4 1 Navigating the control panel 4 2 Menu map 4 3 User configurations Setup single desk light s autocephaly moving mode self motion move Setup single desk light s autocephaly moving mode sound control Master slave mode master sound master auto To set the pan to reverse or non inverting To set the tilt to reverse or non inverting To set the LED readout to inverting or non inverting resume reverse windows default DMX mode 4 4 DMX channel values 5 Technical specifications oO NON NON NO D OO M OO O O O O Gi UC CG HW HNHNNDN 1 Preface 1 1 Packing list quantity Mini Moving Head Light 1 2 Unpacking instructions On receiving a fixture carefully unpack the carton check the contents to ensure that all parts are presented and have been received in a good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows sign of mishandling
5. e data grade cables that can carry a high quality signal and are less prone to electromagnetic interference DMX data cable Use a belden 9841 or equivalent cable which meets the specifications for EIA RS 485 applications Standard microphone cables cannot transmit DMX data reliably over long distances The cable will have the following character 2 conductor twisted pair plus a shield maximum capacitance between conductors 30 pF ft maximum capacitance between conductor and shield 55 pF ft maximum resistance of 20 ohms 1000ft nominal impedance 100 140 ohms 3 3 3 Pin to 5 Pin conversion chart Note If you use a controller with a 5 pin DMX output connector you will need to use a 5pin to 3 pin asapter CHAUVET Model No DMX5M orDMX 5F The chart below details a proper cable conversion Occupation of the XLR connection DMX output DMX input XLR mounting sockets rear view XLR mounting plugs rear view dn Shield o ND Signal Signal Not connected Not connected 3 4 Setting up a DMX serial data link At first link the first light and DMX control through XLR connection signal cable then devolute the light in series as follows Iz Dm DMX 512 DMX 512 DMX Controller 3 5 Master Slave fixture linking 1 Connect the male 3 pin connector side of the DMX cable to the output female 3pin connector of the first fixture 2 Connect the end of the cable coming from the first f
6. electronic strobe Variable electronic dimmer 0 100 LED display menu with invert Reset to factory settings option Pan tilt invert option Fan cooled 2 2 DMX Channel 1 Pan 3 1l 2 J Tit J 3 Pan TiltSpeed XJ 4 Rd O 5 Gen 6 B A 4L0 O ae 8 HPMicoo Z J J4 9 StrobeandReset 10 Dimmer O 11 PanFne A bi 12 Tilt Fine 3 Setup 2 3 4 D 7 10 11 12 Disconnect the power cord before replacing a fuse and always replace with the same type fuse 3 1 Fuse replacement With a flat head screwdriver wedge the fuse hold out of its housing Remove the damaged fuse from its holder and replace with exact same type fuse Insert the fuse holder back in its place and reconnect power 3 2 Fixture linking You will need a serial data link to run light show of one or more fixtures using a DMX 512 controller or to run synchronized on two or more fixtures set to a master slave operating mode The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support Maximum recommended serial data link distance 500 meters 1640ft Maximum recommended number of fixtures on a serial data link 32 fixtures Data cabling To link fixtures together you must obtain data cables If you choose to create your own cable please us
7. ices Please refer to the instruction under control board To set the pan to reverse Press the MENU until it shows RPOF Use the UP DOWN buttons show RPON press ENTER to confirm To set the tilt to reverse Press the MENU until it shows RTOF Use the UP DOWN buttons show RTON press ENTER to confirm To set the LED readout to 180 rotating Press the MENU until it shows RDOF Use the UP DOWN buttons show RDON press ENTER to confirm Resume reverse Windows default Press the MENU until it shows DFON press ENTER to confirm DMX mode This mode allows the unit to be controlled by any universal DMX controller The default mode for the fixture is DMX as follows 4 4 DMX channel values 0255 Panmovement 00 0 255 Pan movement BNET ne 0 255 Tilt movement Red 0 255 0 100 Red Green 0 255 0 100 Green Blue 0 255 0 100 Blue Amber 0 255 0 100 Amber Mixed Color No function Macro 1 Macro 2 Macro 3 Macro 4 Macro 5 Macro 6 No function Strobe and Reset LED off LED on Heset Strobe effect with increasing speed Random strobe effect with increasing spped LED on 0 oessod p dmme O OOO 0 255 0 100 dimme ass BR 0 255 Pan fine pese OOOO O 0 255 Tilt fine 5 Technic data 3 Pan Tilt Speed 0 255 Pan Tilt Speed Voltage 230V 50Hz Fuse 5A 5x20mm Lamp resource 12pcs 12w LED Pan 630 16bit fine Tilt 2 0 16bit fine Tiptop environment temperature 104
8. ixture which will have a female 3 pin connector to the input connector of the next fixture consisting of a male 3 pin connector Then proceed to connect from the output as stated above to the input of the following fixture and so on 3 6 orientation This fixture may be mounted in any position provided there is adequate room for ventilation 4 Operating instructions 4 1 Navigating the control panel Access control panel functions using the four panel buttons located directly under the LCD Display MENU Used to access the menu or return to a previous menu option EEG ian i E N i O i o 0 0 0 0 0 0 0 ia in 1905 DOWN ib through menu options in descending Scrolls through menu options in ascending order C C C ENTER Used to select and store the current menu or option within a menu MENU DOWN UP ENTER When a menu function is selected the display will show immediately the first available option for the selected menu function To select a menu item press lt ENTER gt Press the MENU button repeatedly until you reach the desired menu function Use the UP and lt DOWN gt buttons to navigate the menu options Press the ENTER button to select the menu function currently displayed or to enable a menu option To return to the previous option or menu without changing the value press the lt MENU gt button No alteratived worth that return re option or menu press MENU button
9. r voltage and that the line voltage you are connection to is not higher than that stated on the decal or rear panel of the fixture This product is intended for indoor use only To prevent risk of fire or shock do not expose fixture to rain or moisture Make sure that there are no flammable materials close to the unit while operation The unit must be installed in a location with adequate ventilation at least 20in 51cm from adjacent surfaces Be sure that no ventilation slots are blocked Always disconnect from power source before servicing or replacing fuse and be sure to be replaced with same fuse size and type Secure fixture to fastening device using a safety chain Never carry the fixture solely by its head Use its carrying handles Maximum ambient temperature Ta is 104 F 40 C Do not operate fixture at temperature higher than this In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people will lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to a dimmer device Make sure the power cord never crimped or damaged Never disconnect the power cord by pulling the cord Avoid directing eye exposure to the light source while it is on 2 Introduction 2 1 Features 12 channel DMX 512 Pan 630 tilt 270 Variable
Download Pdf Manuals
Related Search