Technical Guide 2010 Panasonic 3D Plasma TV (13th Generation)
Contents
1. olide 58 Gaw Power On Operation 3D Model TC P50VT20 The power command from the power switch on the A board or the remote control receiver on the K board is provided to the CPU IC1100 in the A board The CPU on the A board outputs 2 commands 1 The TV SUB ON command 2 The PANEL STB ON command The TV SUB ON 3 2V command is provided to the power supply on pin 5 of connector P7 The power supply outputs F15V to the A board when it receives this command The F15V from pins 6 8 of connector P6 on the P board is applied to pins 6 8 of connector A6 in the A board This voltage is applied to a regulator circuit that generates SUB1 2V SUB1 5V SUB3 3V SUB5V and SUB9V These SUB Voltages are used for signal processing The PANEL STB ON 3 2V is output from the Main CPU IC1100 after it has confirmed the presence of all the SUB voltages This command is used to turn on circuits in the both the A board and the D board e Inthe A board it is responsible for generating the voltages used by the MIHO 3D 1C5800 and the 3D Eyewear Driver Transmitter circuit e Inthe D board it s used to turn on the 3 3V regulator 1 9400 olide 59 Power On Operation P6 9 oon SND 15V of 0 7 AT oi TV SUB ON 5 N P15V LO ol f Ic9804 F25 Panel Drive Slide 60 er Power On Operation When 1 9400 is turned on it2. USB Wi Fi Ready HS 232C VT25 Only The Panasonic 3D plasma TVs also support DLNA DNA Slide 45 Internet Connection Wireless LAN Internet Connection Make sure that the connection speed exceeds the following Atleast 1 5 Mbps for SD Standard Definition e 6Mbps for HD picture quality Note Dial up Internet service cannot be used for VIERA CAST Wireless LAN The DY WL10PP K Panasonic wireless LAN adaptor can connect with your TV Connection with the following Access point has been confirmed for use of wireless LAN adaptor DY WL10PP K with your TV NETGEAR WNDR3300 WNR2000 Linksys WRT400N WRT120N e D LINK DIR 655 Slide 46 Connection HDMI Cable There are two types of HDMI cables Standard HDMI Cable and High Speed HDMI Cable Use High Speed HDMI Cable corresponding to FULL HD 3D Connecting a BD player to a 3D Plasma TV Connecting a BD player and a Home Theater to Only a HDMI cable is needed a 3D Plasma TV 2 HDMI cables are needed Connection of optical digital cable is not necessary The Audio signal is transmitted from 3D Plasma TV video audio input terminal to HDMI video audio output terminal of theater HDMI Video 3D Plasma TV Audio HDMI 1 eater Terminal Slide 47 Slide 48 TC P50VI20 2 ki t m um Ex Um ee Slide 49 3D Model TC P50VT20 ee de 50 SI
3. FE ZX LI m Relays clk on and continous W TV s Behavior After Connectors Removal MODEL NO TC P50VT20 a Removal on the SC Board Es an 2 SOS 6 Blinks SC20 nm SOS 6 Blinks sca sossme 9 MODEL NO TC P50VT20 Connectors Removal on the SS combination of connectors m on and SC board onnector o SC B Connector u NEN 222227 x 27 Wa on SS330rC33 50578 5 2 S 7 Blinks ZZ m 5533 or C33 nn 5 20 SOS 6 Blinks 5533 or C33 5 20 SOS 6 Blinks SS11 5533 or 33 20 SOS 6 Blinks olide 97 Glossary Resolution Resolution is a combination of values that express the quality of displayed images A display s resolution is indicated by the number of dots in the horizontal and vertical directions of the screen such as 1024 x 768 dots Higher values indicate clearer sharper image reproduction larger the screen size the higher the required resolution HD high definition panel The HD panel has a resolution of 1 366 x 768 pixels and an aspect ratio of 16 9 It is designed for displaying the beautiful images of digital high definition broadcasts Full HD high definition panel The term full HD panel refers to 1 920 x 1 080 pixel panels that display progressive images of full specification HDTV si
4. 4 Enlarged Discharge Area improves brightness and contrast with less power consumption The new cell structure materials and phosphors made it possible to enlarge the discharge area of each cell This increases both brightness and contrast so you enjoy a bright vibrant picture while using less energy High Contrast Images with Lower Power Consumption a j Conventional Slide 10 New Plasma Display Panel 2 ANew Filter It blocks ambient light to increase contrast and brightness A newly developed film minimizes reflection from ambient lighting and increases contrast also improves light transmittance which boosts brightness The result is reproduction of images that look breathtakingly beautiful in any viewing environment glass m Filter Ambient light Rich Gradation and Extreme Deep Black NN Pre dischar ge piLat Light Conventional 2010 New Cell 3 Reduced Pre Discharge Reduces grey and enhances black gradation To minimize light leakage we found a way to reduce the level of pre discharge required for plasma light emission This helps achieve deeper richer blacks that give images exceptional depth and presence Slide 11 THX THX reproduces film images exactly as the film s creators intended them The aim is to recreate the audio and visual ambience that filmmakers intended To receive THX certification TVs undergo stringe
5. Select Change On 4 Off B _ 2 ee 5 P d IN 4 di _ f s 2 E nm 3D settings 3D Eyewear Left Right swap Diagonal line filter Safety precautions Select Change enETURN powered 1asonic How to change from 2D to 3D Change it from Auto to Top and bottom 3D settings 3D Eyewear 3D input format Left Right swap Normal Diagonal line filter Off Safety precautions Select Change eRETURN Slide 41 sf hik wa x m nem NEW 0 4 pu Slide 42 How to change from 2D to 3D Then press the EXIT button on the remote INPUT GAME VIEfA EXIT MUTE FORMAT INFO FAVORIT Slide 43 Slide 44 USB Ports R It is not warranted that all USB devices will work with I Sid It allows playback for photos video clips and music E Rear It does not read hard drives It does not support USB device charging ear FAT12 FAT16 and FAT32 file systems are _HDMI1 Position Rear supported This unit supports USB 2 0 High Speed Using the USB ports the TV is also WiFi ready but you need to purchase a dongle separately Wireless LAN Adaptor DY WL10 C5ZZZ0000048 SD Function Movie amp Photo
6. 9300 or 109400 triggers a shutdown and the power LED blinks 9 times olide 80 D Board SOS Detect Block Diagram I 25 025 2 1 3 3V REG gt P 15V DET SC POWER 2 2 le SOS2 7X VCC Vsus DET Vda DET 63 15 DET PANEL z z n 701 POWER MCU PANEL POWER PART SOS DET pr 5 8 7 F STBY ON 52 1100 SYSTEM CPU olide 81 8 Blinks Error Code 6251 Comparator R16284 50358 816280 FeCDET _ OT 505 4 016280 Su D16281 5521 7 55241 7 olide 82 8 Blinks Error Code R16284 f gt R16281 016245 816359 o TPSOS8 5533 AA 5058 TP36 816280 FPC m 01520 KON T 16281 2 5521 im slide 83 9 Blinks Error Code This condition can cause the TV to shutdown and the power LED to blink 9 times 1 No communication between 1C9300 9004 and IC9003 Since these ICs are located on the D board only the D board can cause the TV to shutdown with 9 blinks of the power LED SLAVE MASTER IC9400 IC9300 Plasma Al x x PD4 IC9003 CPG with x Plasma Al x GenX7 H V Sync Control CPG with SS Ponel nen Trece H V Sync Control B27 E Sub Field Processor _B27
7. Connectors Location olide 51 Slide 52 otart up Process Upon connecting the Panasonic 3D Plasma Display Television to the AC line the sound of relays being triggered can be heard from the Power Supply board Also a red light from the Optical jack on the back of the TV can be observed Approximately 15 seconds later the click sound from the relays can be heard again and the red LED inside the Optical jack turns off This condition is normal and by paying attention to this sequence of events we can confirm the operation of several circuits inside the TV olide 53 TV Start Up Procedure The power supply generates the voltages necessary for signal process and panel drive operations When the power is turned on the power supply outputs F15V and P15V Sound amp to the A board for signal processing Then Vsus Vda and P15V are output to the panel drive section Signal Processing F15V Video I P15V Sound Scan Control Sustain Control Vsus Vda P45V Data Control Power AA Supply Panel Drive Voltage F15V Video P15V Audio Amp Voltages ENS Vsus Vda P15V Power This is an illustration of the actual signal processing section and the panel drive section olide 54 otandby Operation Signal Processing To Main CPU amp K board R C Rec Panel Drive The STB5V from the Power Supply is connected to the A and the D boards During standb
8. All Panasonic VIERA VT25 Series models also feature 600HZ Sub field Drive 1080p Lines Moving Picture Resolution VIERA Image ViewerTM VIERA LinkTM Connectivity with Network Cameras 24p Cinematic Playback two USB Ports PC Input and are ENERGY STAR 4 0 compliant Slide 7 Surround Sound Control Balance Control Lip Sync Improvement AM1 Type Position UJ UJ m AV2 Type Position Component Type Position Component2 Type Position HDMI1 Position HDMI2 Position HDMIS3 Position HDMI4 Position PC Input Digital Audio Out Ethernet VT SERIES RCA S Rear RCA Side RCA Rear RCA Rear Rear Rear Rear Side lt Specifications Resolution Contrast Native Gradation Filter Remote THX Deep Color X V Color Game Mode Motion Reality VT SERIES 1920X1080 Infinite 1 6144 Louver Direct filter w Viera Cast 1080 lines SD Card Slot SD Card LED Color SD Function USB Wi Fi Ready RS 232C DLNA IPTV VT SERIES Blue Movie amp Photo VT25 Only Viera Cast slide 8 FHD 3D Panasonic Consumer Products 3D Plasma IV BD Player Home Theater 40 20 DMP BDT300PP SC ZT2 TC P50VT25 DMP BDT350PP MEM TC P54VT25 DMP BDT100PP olide 9 New Plasma Display Panel The new panel used on the 2010 3D plasma TVs has 3 areas of improvement 1 Enlarge discharge area 2 New filter 3 Reduced pre discharge
9. SOS DDC olide 84 D Board SOS Detect Circuit Explanation One of the multiple functions of IC701 Power MICOM is to detects abnormalities on the Power Supply Abnormalities in the P board are reported to IC9003 via the SOS4 input The 5052 15V 5053 5055 detect input lines of IC9003 monitor for missing voltage or short circuit of the 15V 3 3V and inputs to the D board The remaining 5056 and SOS 7 inputs monitor for abnormal operation of the SC and SS boards A defective D board may also be responsible for the 2 3 4 5 6 7 8 or 9 blinks of the power LED A defective component on the D board may supply the MPU IC9003 an erroneous input that causes the unit to shut down with the power LED blinking a number of times the D board does not control the blinking pattern of the power LED any detected SOS condition must be reported to the A board MPU IC1100 The alarm pin of IC9003 reports all SOS detections to the A board MPU The ready pin of IC9003 is an acknowledgement line that reports the operational status of the D board to the A board MPU olide 85 11 Blinks Error Code Fans A30 1 X2 KS X4 X56 K7 X8 X9 000382 1610 50 17 05749 FAN STOP sanla 11V Zener SOS DET TV SUB ON olide 86 11 Blinks Error Code Explanation The internal temperature of the unit is monitored by the digital temperature sensor 169002 Variations in temperature are sensed by the IC and report
10. To Exit the Self Check Mode Press and hold the Power button on the TV for 5 seconds or disconnect the AC cord from the wall outlet Heset Procedure Reset forces the TV to factory shipment setting Note All customer programmed parameters will be erased To Reset the TV Press and hold the VOLUME button on the TV and press the MENU button on the remote control for more than 3 seconds To Exit Disconnect the AC cord from wall outlet To Exit Disconnect the AC cord from wall outlet Slide 91 Mirror Function This feature allows the picture to be rotated 180 horizontally or 180 vertically When servicing plasma TVs with horizontal lines this feature can help to determine if the A board is causing the problem or not For vertical lines problems this feature can help to determine if the problem is the A board or the panel The rear cover does not have to be removed to do this If the position of the line lines changes when performing this function the A board is possibly defective If the line lines do not move 1 For horizontal lines check between the panel and the SM board 1 For vertical lines change the panel To enter the Mirror Function From the Service Mode Menu select OPTION Press 3 or 4 to select MIRROR Press the VOLUME up or down button to change the Mirror s data Data 00 is the default data Mirror feature is off Data 01 The picture is flipped 180 horizontally Data 02
11. from creating catastrophic damage A shutdown condition occurs when a there is an over voltage a short or a drop in any of the voltage lines Also when the fans are drawing more current than normal the shutdown circuit is triggered Normally the CPU of the D board and the CPU of the A board detect when a shutdown condition has been triggered When an abnormality has occurred the unit protection circuit operates and the 15 reset 10 the stand by mode At this time the defective block can be identified by the number of blinks of the POWER LED on the front of the unit 9003 of the D board detects conditions that make the power LED blinks 2 3 4 6 7 8 or 9 times IC 1100 on the A board detects conditions that make the power LED blinks 10 11 and 12 times Slide 77 Power LED Error Code Definition 1 of 2 The following table identifies the areas where a problem is suspected according to the number of times that the POWER LED blinks Panel Infomation SOS Communication problem between the System CPU Panel AlarmSOS IC1100 and the Panel CPU IC9003 Missing 15 P15V is not been generated by the P board 2 BLINKS P15V formthe P board e P15V is been affected by one of the boards it is connected to A short circuit of the 15 Wrong diagnostic by the D board Missing P3 3V Reasons The A board is nct generating the 3 3V 9 The 33V is been affected by one of the C boards or the Panel A short circuit of t
12. INFO button of the remote control three times within 2 seconds Service Mode Screen DTVSOCSOFT 1 090 RB Cnt 1 01 0167 1 31 00 1 00 01 01 00 0187 02 00 SERVICE ADJUST WB ADJ OPTION VSUS AGING SRV TOOL 33 43 73 03 33 41 200 1 button Main items Selection in forward direction 2 button Main items Selection in reverse direction 3 button Sub items Selection in forward direction 4 button Sub items Selection in reverse direction VOL button Value of sub items change in forward direction in reverse direction How to exit Switch off the power with the POWER button on the main unit or the POWER button on the remote control Slide 90 Self Check Reset 1 Checks the communication IIC bus lines 2 Provides a SOS History To Access the Self Check Mode turn the TV on and while pressing VOLUME button on the main unit press the OK button on the remote control for more than 3 seconds TV volume down amp OK on remote only does a basic IC self check It does NOT clear any unit settings It does not clear channel programmed settings picture settings channel labels LOCK mode settings or password Using this method it shows the unit firmware version Peaks 1 050 and GenX 1 00 and it checks IC communications ONLY This is more useful to identify the firmware version without having to decode the info in the setup menu About Version screen
13. The picture is flipped 180 vertically olide 92 Mirror Function Picture flipped Horizontally Normal View Defective A board 1 2 MAIN SELECT 3 4 SUB SELECT 9 PICTURE MENU SELECT VOL ADJUST i Normal View Picture flipped Vertically OPTION VIVID Defective A board Er pn ET WEMN 2ETEC1 2ETECL 1 2 MAIN SELECT 3 4 SUB SELECT 9 PICTURE MENU SELECT WIBBOB 0 110 Slide 93 TV s Behavior After Connectors Removal 50 20 mE Bil o 9 p p ve we uf 9 1 jo 2 2 23 0 Slide 94 TV s Behavior After Connectors Removal stays ON wit ack bottom right quadrant HM __ SOS 6 Blinks 77 SOS 6 Blinks G G G Ep Z TV turns on by itself at plug in wit x No fans _ OO 1 connectors are unplugged 2202 8 SOS 1 Blink D32 D33 D34 I N C SOS6Blnks B31 baa bai bas 022 56s olide 95 TV s Behavior After Connectors Removal PEAS 2 E non 25 25 SS SSS B IE 1 7 2 2 2 S m YY v ed ee 62 U ep er e
14. Ver 1 4 Under HDMI Digital signal HDMI Ver 1 4 HDMI Ver 1 3 vlr HDMI Ver 1 4 under 1 R L c Support Situation HDMI Ver1 4 HDMI Ver1 4 Auto User manual Setting method Auto Other User setting manual setting BD contents use BD recorder Format used for cannot accept PC etc this T amp B format this FS format Only HDMI Ver 1 4 can recognize 3D signal 3D signal is only for the digital input PC and an external analog input etc do not accept 3D signal Slide 17 3D Display Formats Methods Line by Line Field Sequential Frame Sequential Left eye images Right eye images A sequential 3D TV can display sequential 3D this means the TV converts it Blu ray outputs the video at 1080p 24 frames per second per eye or 48 frames per second This signal goes to the TV but the glasses are what ensures each eye sees the correct image The side by side systems a single 1080p frame that holds both the right and left eye s images is sent at 24 frames per second The TV receives this signal splits it into two frames displays them sequentially and then stretches them out This is not as good as Blu ray but it uses way less bandwidth and makes it so that the TV Station Like DirecTV can just release a firmware update instead of replacing all the set top boxes It is expected that cable companies will use the same technique Auto Stereoscopic TV is the future The 3D image i
15. features new faster screen phosphors short stroke which when coupled with the VIERA VT25 s 600Hz sub field drive outputs alternating imagery at 60 frames per second to each eye Working in unison with the required Active Shutter Eyewear the human brain then combines the images and interprets them as a Full HD 3D image for the highest possible realistic visual experience in effect mimicking what the human eye sees in real life Active Shutter Eyewear All Panasonic VIERA VT25 Series models come with one pair of Panasonic 3D Active Shutter Eyewear TY EW3D10U Additional pairs of Panasonic 3D Eyewear are available at retail with an SHP of 149 95 Infinite Black Pro Panel A new phosphor technology that produces deep blacks 5 000 000 1 native contrast 2 and vivid images with minimal reflection THX Certified Display Ensures that every Panasonic Full HD 3D IV displays motion pictures and television content with exactly the quality and color palette that the director intended VIERA CAST WiFi with Skype Capability Panasonic s innovative Internet programming package gives viewers the ability to access feature films plus information and communication offerings including Amazon Video on Demand Bloomberg News Fox Sports Netflix and Skype on Your VIERA 1V3 among others Access to a broadband Internet connection is required Panasonic s Communication Camera 1 Y CC10W is required for Skype video functionality and sold separately
16. fromthe panel Open or loose connection between connectors C10 C20 Vong diagnostic by the D board Defective panel Failure of IC9300 VWrong diagnostic by the D board Abnorrralities of the FSV Reasons The P board is not generating the F A5V SUB Voltages are affected by the K board or by rretal object preserx in the SD card slot Shorted Vsus By the SS board or SC board Shorted Vda By the panel or any of the C board di the board Fans A board Connection and Cables between fans and A board Slide 79 SOS Detect Circuit 1 Blink SOS Communication error between System CPU 161100 and Panel CPU 169003 2 Blinks SOS Pin 62 of the CPU IC9003 monitors the 15V line During normal operation the pin 62 is high If the 15V line is missing or shorted a low is provided to pin 62 As a result the unit shuts down and the power LED blinks 2 times 3 Blinks SOS 169802 is a 3 3V regulator located on the D board Its output is monitored by IC9003 If the 3 3V is not present at pin 61 the MPU shuts down the unit The power LED blinks 3 times 4 Blinks SOS When an over voltage condition of the voltage lines from the power supply occurs pin 16 of 1C701 goes high This high is provided to pin 67 of 19003 of the D board triggering the POWER SOS circuit When this happens the TV shuts down and the power LED blinks 4 times 5 Blinks SOS Pin 60 of the CPU IC9003 monitors the 5V line During normal operat
17. images for the left and right eyes in frame sequential is unique to Panasonic The Panasonic 3D PDP utilizes new phosphor technology for real deep black and unsaturated brightness and employ proprietary 3D drive technology circuitry to minimize crosstalk between alternating images olide 3 Slide 4 oeries Line up SEHRIES MODELS VI SERIES TC P50VT25 TC P54VT25 TC P58VT25 TC P65VT25 FHD Premium 3D TC P50VT20 Differences between the 20 and VT25 models The VT25 Series models offer ISFccc calibrated with an RS232C jack and Studio reference mode and Pro Setting ISFccc is a protocol used to help professional BB ISF calibrators to adjust the TV for a perfect picture RS232C Jack VT25 for custom installations The bezel color of the VT20 is qunmetal silver grey while The bezel color of the VT25 Series models is a deep brown metallic olide 5 New Features High Picture Quality FHD 3D Dual Sca Short Stroke 27 THX Certified Moving Picture 1080 Lines 600Hz Sub field Drive Infinite Black Plus Native CR gt 2 Mil 1 Smart Networking Viera Cast IPTV Wi Fi Ready USB x2 VIERA Image Viewer Movie amp Photo Viera Link 4 HDMI Ports Stylish Design Metallic C Environmentally Energy Saving Louver Filter Friendly Mercury amp Lead Free 100 000 hrs Eco Mode olide 6 Features Full HD 3D Technology For a true Full 1080p 3D image Panasonic s VI25 Series
18. D expression of the images 1 Change the switch to 3D and 2D repeatedly 2 Glass color is changed to dark and bright by detecting a Shutter On Off signal from TV if they are working propely nn p bod TV outputs IR signal from 2 positions Even if one IR signal is blocked the 3D 2D Shutter Off 3D Shutter On 2D Shutter Off eyewear will receive the other IR signal After 5 sec olide 26 How to check signal from IV set Detail 3D setting Set the 3D 2D select switch on the user menu to 3D to confirm the IR output signal from the TV by using Mobile Phone s Camera Left Right phase reversal Attention 9 Note This will not work with cameras with IR filters eem Sec Change RETURN 3D Auto 3D gt 2D gA ewe 2D IR Output OFF There are total six IR output LED 3D IR Output ON 2D IR Output OFF 3D IR Output O Cell Phone s camera LED are indicated if TV is working propery Slide 27 Slide 28 Basic Components Source 3D Eyewear Display High Speed HDMI Cable 1 4 3D UID Only the HDMI inputs are compatible with the 3D mode Slide 29 3D Sources 3D Blu ray Player Satellite Cable and Over the Air Signal Digital or HD service subscription and a direct cable connection or an HD STB Set Top Box are required e lf a STB is used an HDMI connection between the cable box and the TV is required e
19. ER HDMI I F RECEIVER A31 05 TMDS DATA LVDS DATA LEFT LVDS MIHO 3D HDMI3 HDMI4 TMDS DATA 8300 IFD OUT FRONT END CHODATA AV SW IC3001 IR_L PEAKS LDA2 IC8000 3D EYEWEAR DRIVER 105814 A OUT LVDS DATA Zar B IN Slide 67 Digital Signal Processor Explanation The main function of the A board is to select and process one of the incoming video signals Analog signal from Video inputs 1 and 2 Component Inputs 1 and 2 PC input and the composite video output of the tuner are all connected to IC3001 for selection The video output signal Y Pb Pr enters the PEAKS LDA2 IC IC8000 for processing The digital signal from the 4 HDMI ports is also provided to IC8000 Only HDMI is ARC Audio Return Channel compatible The data from HDMI 1 and HDMI2 are connected to an Equalizer to allow for longer cables to be connected to these 2 ports USB data Ethernet data and JPEG data of the SD card are also connected to IC8000 All picture control operations such as brightness contrast color tint etc are performed by IC8000 On Screen Display data such as channel numbers Digital TV closed caption and picture adjustments are mixed with the video data The signal is then converted LVDS Low Voltage Differential Signaling The LVDS data from IC8000 enters the MIHO 3D 1C5800 IC5800 separates the LVDS data into right LVDS and left LVDS and also outputs the IR synchronizi
20. Panasonic Applies to models TC P50VT20 TC P54VT20 TC P50VT25 TC P54VT25 TC P58VT25 TC P65VT25 Technical Guide Panasonic Service and Technology Company National Training TTG090507CP REV090717 Prepared by Cesar Perdomo Panasonic Service and Technology Company National Training HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC Copyright 2009 by Panasonic Service and Technology Company All rights reserved Unauthorized copying and distribution is a violation of law Warning This service information is designed for experienced repair technicians only and is not designed for use by the general public It does not contain warnings or cautions to advise non technical individuals of potential dangers in attempting to service a product Products powered by electricity should be serviced or repaired only by experienced professional technicians Any attempt to service or repair the product or products dealt with in this service information by anyone else could result in serious injury or death Slide 2 Introduction The Panasonic 3D Plasma TV uses what s called Frame Sequential Method By using this method the TV outputs alternating imagery at 60 frames per second to each eye The brain then combines the images and interprets them as 3D The PDP high speed light emission technology utilized to display high picture quality full HD video
21. The or STB needs to be tuned to the channel with the 3D broadcast e Stereoscopic 3D glasses are required Customers should contact their cable or satellite service providers to see if they are subscribed to a service which provides 3D content or check their local listings for channels this will be carried on for off air broadcasts The issue is that there may not be a 3D Content Flag embedded in the signal which would cause the TV to automatically change to the correct 3D Input Format so customer may have to make this change in the TV s menu manually They may need to manually change this setting until the EDID VSI information that will allow our TVs to automatically switch to 3D mode is included in the broadcast olide 30 3D Settings Menu There are two ways to enter the 3D menu to adjust the 3D settings 1 By pressing the VIERA Tools on the remote control Press remote VIERA Tools button then select 3D 2 By pressing the Menu button on the remote control Press remote MENU button then select Setup gt 3D settings Note Both are actually same menu as next page However from VIERA Tools the message below will be displayed except when TV ANT In Antenna or HDMI input is selected instead of 3D settings Enjoy an entirely new viewing experience with Panasonic 3D Display 3D content via an HDMI connected device or 3D DTV signals via the Antenna input Slide 31 3D Settings Menu 3D settin
22. ated design guidelines for a new generation of DLNA Certified products that can work together no matter the brand DLNA Certified devices today connect discover and communicate with each other over a home network Slide 100 The End Slide 101
23. e transmitted so when connecting home theater system between VIERA and DIGA use 3D home theater system 1080 lines x60 frames second 1080lines x60 frames second Note FULL HD SD Video signal have double the information data of 2D video signal Slide 20 Eyewear EW3D10U EW3D10 Full HD 3D Eye ware High Precision shutter control sends clear images to each eye Highly precise control completely closes the shutters for both eyes at the instant that the images change for the left and right eyes This masks unwanted afterimages to enable clear and comfortable 3D viewing Features Adjustable durable frame The Eyewear can be easily adjusted to fit various face shapes and sizes from children to adults Designed for use together with ordinary glasses The 3D Eyewear can also be comfortably worn right over ordinary prescription glasses Power on off switch An Auto Power Off function automatically turns the glasses off if they are placed in a location outside the viewing range or IR receiving distance 3 2m 10 5 for 5 minutes even if the TV remains turned on 3D Eyewear case included The 3D TV comes with 1 pair of 3D Eyewear necessary to view the 3D content Additional 3D Eyewear may be purchased separately Warning In the event that you experience dizziness nausea or other discomfort while viewing 3D images discontinue use and rest your eyes Parents guardians should monitor children s viewing habits to avoid their prolo
24. ed to the D board MPU 9003 via the SDA02 bus line IC9003 then conveys the information to the A board MPU IC1100 via the SDA1 bus line Fan speed is controlled by IC9003 The ventilation fans are monitored to be sure they are operating properly If one of the fans opens or increases resistance the resulting current change is applied to pin 61 of the main CPU IC1100 The fan drive circuit is located on the A board To control the speed of the fan a control voltage from the microprocessor IC1 100 is applied to 5740 If any of the fans is removed or becomes defective a high is output at the corresponding pin pin 3 9 or 12 of the fan connector A30 to forward bias the inline diode The DC output of the diode Is provided to pin 61 of IC1100 to trigger the SOS condition olide 87 12 Blinks Error Code Sound 1100 27 N SOS SYSTEM CPU SOUND SOS SOS NORMAL SOUND PWM A PROCESSOR 2302 The transistor 022300 monitors the speaker amplifiers ICs 12301 and 2302 Pin of both ICs is normally high If any of these ICs or one of the speakers develops a short circuit pin 3 goes low causing Q2300 to go into conduction and output a low to the base of Q2300 As a result Q2300 comes on and outputs a high to pin 27 of the System CPU IC1100 on the A board olide 88 Slide 89 Service Mode While pressing the VOLUME button of the main unit press the
25. gnals without the use of up sampling Number of pixels The number of pixels indicates the resolution of the Image The number of pixels of a digital image is expressed by the product of the number of pixels dots in the horizontal direction and the number of pixels dots in the vertical direction higher the number of pixels the better the image quality For plasma TVs and LCD TVs the number of pixels is sometimes expressed by the following equation number of pixels in horizontal direction x number of pixels in vertical direction x 3 B Pixel A pixel is a tiny dot that forms the smallest basic unit of a displayed image Digital images are composed of pixels with all of the text and images displayed on the screen consisting of dots Digital images are usually rendered by square pixels arranged vertically and horizontally in an orderly manner Plasma panel A key component of the plasma display A plasma panel is a collection of millions of tiny fluorescent lights By firing these lights on and off at a rapid rate the plasma panel produces images olide 98 Glossary THX is a trade name of a high fidelity sound reproduction standard for movie theaters screening rooms home theaters computer speakers gaming consoles and car audio systems THX stands for Tomlinson Holman s eXperiment The THX system is not a recording technology and it does not specify a sound recording format all sound formats whether digital Do
26. gs Function 3D Eyewear On Default option Select when Eyewear Glasses is used for watching Select when Eyewear Glasses is not used including even when 3D signal is Side by side received Because customer cannot watch 3D images without the glasses 3D input format o For details see next page omon Fun Diagonal line filter On Auto Default option Select 3D 2D automatically regardless of input format safety precautions Side Side by side side Select 3D Select 3D manually when input format is Side by side such as DirecTV when input format is Side by side such as DirecTV and 3D manually when input format is and bottom bottom Native Display the input signals as is on the screen For customers service Because TV cannot detect left right phase in some 3D signal formats this option is used when customers feel strange in depth perception Function Normal Default option To set Left Right phase straight Swapped To set Left Right phase reversed option _ _ Processing input video as Quincunx matrix signal only when Side By Side or Top And Bottom is received Default option Processing input video as Horizontal sub sampling signal only when Side By Side or Top And Bottom is received To display Safety Precautions message Slide 32 9D input format Matrix Between Menu and Actual Cor
27. he P3 3V Wrong diagnostic by the D board Regulation issues with any of the voltages output fromthe Power Supply output 4BLINKS power supply voltages I Wrong diagnostic by the D board Missing 5 Reasons 5BLINKS P5V fromthe A board e Theb5V is been affected by the SC SS or C2 board A short circuit of the P5V Wrong diagnostic by the D board An increase or reduction of the Energy Recovery Circuit output MID Open connection between connector D20 on the D board and SC20 on the SC board 6BLINKS SC Energy Recovery Circuit Open connection between any of the ribbon cables on the C boards and the D board Open connection between the ribbon cable cables interconnecting the C boards Wrong diagnostic by the D board Slide 78 3BLINKS P3 3V fromthe D board Power LED Error Code Definition 2 of 2 Scan Drive Circuit and Connection between the SC board and the SM board 7 BLINKS Sustain Drive Circuit and Connection between the SS board and the Panel Discharge Control Circuit Missing Vsus Abnomrelity of the scan circuit output the 15V F the scn pro and Vscn circuit Loose or open Connection between the SC board and the SM board SCA SCA2 SC46 Open or loose connection between connectors SC2 P2 Vong diagnostic by the D board Defective panel Abnorrrality of the sustain drive circuit Open or loose connection between the SS bd and FPCs
28. hen the oM board is isolated The jig is a small connector with a jumper between pin 1 and pin 2 The part number is TZSC09187 It plugs into connector SC50 on the SC board Note If the SC jig is not available install a jumper between pins 1 and 2 of connector SC50 on the SC board Remove the jig or the jumper after completing the isolation procedure When this is done the display is completely black No picture Slide 75 When an abnormality occurs in the unit the SOS Detect circuit is triggered and the TV shuts down The power LED on the front panel will flash a pattern indicating the circuit that has failed Cautions If the power LED continues to blink even after the TV is unplugged press and hold the power switch on the TV for a few seconds until the LED turns off oome steps require removal of connectors and sometimes PC boards removal Do not allow the TV to run for more than 30 seconds while connectors or boards are disconnected Warning The Vsus line has large capacitors that hold the charge for some time even after the has been turned off and unplugged When disconnecting P2 SC2 or 11 551 bleed the remaining charge of the Vsus before reconnecting the cable Use a 500 ohms 5W At least resistor to discharge the Vsus line before reconnecting P2 SC2 or P11 SS11 Slide 76 SOS Detect Circuit Protection circuits are incorporated in the unit to prevent the failure of a single circuit or component
29. ion the 69 is high If the 5V line is missing or shorted a low is provided to pin 60 As a result the unit shuts down and the power LED blinks 5 times 6 Blinks SOS Pin 65 of the CPU IC9003 monitors the status of the SC board During normal operation a low is applied to pin 65 If the SC board becomes defective a high is provided to pin 65 As a result the unit shuts down and the power LED blinks 6 times 7 Blinks SOS Pin 68 of the CPU IC9003 monitors the status of the SC SU SD board During normal operation a low is applied to pin 68 If the SC SU or SD board becomes defective a high is provided to pin 68 As a result the unit shuts down and the power LED blinks 7 times 8 Blinks SOS Pin 66 of the MPU IC9003 monitors the status of the SS board During normal operation pin 7 of connector 5533 outputs a low to 66 If the 55 board becomes defective a high Is provided to pin 66 As a result the unit shuts down and the power LED blinks 8 times Another SOS Detect circuit in the Sustain board monitors for physical connection between the SS board and the panel If any of the flex cables from the panel is not connected or is not properly seated a high is provided to pin 66 of the CPU in the D board When this happened the TV shuts down and the power LED blinks 8 times 9 Blinks SOS Pins 85 and 86 of the MPU IC9003 monitor the status of 9300 and IC9400 During normal operation pin 85 and pin 86 are low A malfunction of
30. ke the 3D objects they are viewing as real objects causing him to move suddenly This may cause damage to surrounding objects leading to injury Slide 14 Can Everybody See 3D No There s a small percentage of human 596 1096 of Americans that lack the ability to properly see different images for each eye This condition is called Stereo Blindness Slide 15 3D Display Formats Methods There are a few methods used to separate the left and right eye images on a 3D display Frame Sequential Side by Side Mu and Bottom Checker Pattern Field Sequential Line By Line SEPT CEP Da Burn nun nu Su Bl aa el un PE OT ee Pane an ln a PO icta ii quise fce cantor bw ewm ee io mr FR t Frame Sequentia Plasma In the frame sequential eid images for each eye are ae reproduced in its full resolution This means a separate 1920 x 1080 Full HD image is sent to each of eye enabling the viewers to fully immerse themselves in the 3D landscape presented Frame sequential is what the Blu Fray nee and active shutter TVs use Side By Side Supporte as
31. lby Digital SDDS or analog Dolby Stereo Ultra Stereo can be shown in THX THX is mainly a quality assurance system THX certified theaters provide a high quality predictable playback environment to ensure that any film soundtrack mixed in THX will sound as near as possible to the intentions of the mixing engineer AVCHD Advanced Video Codec High Definition is a high definition and standard definition recording format for use in digital tape less camcorders and digital cameras It is based on the H 264 MPEG 4 AVC video compression standard Audio is stored in compressed form Dolby 3 The container format for the audio and video is MPEG transport stream H 264 H 264 is a standard for video compression and is equivalent to MPEG 4 Part 10 or MPEG 4 AVC for Advanced Video Coding As of 2008 it is the latest block oriented motion compensation based codec standard The final drafting work on the first version of the standard was completed in May 2003 The intent of the H 264 AVC project was to create a standard capable of providing good video quality at substantially lower bit rates than previous standards e g half or less the bit rate of MPEG 2 H 263 or MPEG 4 Part 2 without increasing the complexity of design so much that it would be impractical or excessively expensive to implement YUV YUV is used for a specific analog encoding of color information in television systems Y stands for the luma component the brightness a
32. les between the C boards follow this procedure in order to prevent the panel from becoming damaged 1 1 Disconnect the TV cos 2 Remove P65 Vda and 82 Ribbon Cables P35 Vda from the power Between the gt 95 9 Supplv C Boards E T pply 3 Reconnect the ribbon cables 4 Reconnect P65 and P35 Slide 73 SU and SD Boards Isolation Procedure The 2008 2009 and 2010 plasma models are designed not to turn on if either the SU or SD board is disconnected Disconnecting either causes the unit to shutdown and the power LED to blink 7 times Unplugging any of the connectors SC41 SU41 SU11 SD11 and SC42 SD42 opens the interlocked connection between VF GND and CHA on the SC board This triggers the 7 blinks SOS detect circuit shutting down the TV and making the power LED blink 7 times Slide 74 oU and SD Boards Isolation Procedure This procedure is useful when troubleshooting 7 blinks problems If the power LED continues to blink even after the TV is unplugged press and hold the power switch on the TV for a few seconds until the LED turns off To isolate the SM board is not necessary to remove any boards L Remove the 4 VF GND screws on the SU and SD boards Unplug connectors SC41 SC46 and SC42 on the SC board Place the SC jig cable TZ8C09187 between pins 1 and 2 of connector SC50 on the SC board The SC test fixture Jig can be used w
33. nd U and V are the chrominance color components olide 99 Glossary YUV Is The color encoding system used for analog television worldwide NTSC PAL and SECAM The YUV color space differs from RGB which is what the camera captures and what humans view Composite Video and S video The original TV standard combined luma Y and both color signals B Y R Y into one channel which uses one cable and is known as composite video An option known as S video or Y C video keeps the luma separate from the color signals using one cable but with separate wires internally S video is a bit sharper than composite video Component Video When luma and each of the color signals B Y and R Y are maintained in separate channels it is called component video designated as YPbPr when in the analog domain and YCbCr when it is digital ASIC An Application Specific Integrated Circuit ASIC is an integrated circuit IC customized for a particular use rather than intended for general purpose use S PDIF Is a Data Link Layer protocol and a set of Physical Layer specifications for carrying digital audio signals between devices and stereo components over either optical or electrical cable The name stands for Sony Philips Digital Interconnect Format More commonly known as Sony Philips Digital Interface DLNA Digital Living Network Alliance A collaboration of the world s leading consumer electronics PC and mobile companies DLNA has cre
34. ng signal to the eyewear The Right and Left LVDS data is then output to the D board olide 68 oymptom Created By a Defective A Board This symptom is an example of a problem created by a defective A board The Right LVDS signal from the A board is missing The A board on previous models never caused this type of problem This is due to the right and left LVDS separation in the A board The D board normally causes this type of problem m ed 3 EN Esa kaa I Eh uli au p et CAL J I i J E ELE Lux panel Drive Control Pulses DEDE 4 ku y d m mcm Pa 517 VIDEO DATA C4 DATA DRIVER RIGHT DATA DRIVER LEFT VIDEO DATA DATA DRIVER fu SCAN OUT UPPER VIDEO DATA D 2 56 SCAN DRIVE SUSTAIN DRIVE LVDS DATA LVDS DATA SCAN CONTROL SUSTAIN CONTROL SCAN CONTROL VIDEO DATA SCAN OUT LOWER SUSTAIN CONTROL VIDEO DATA SUSTAIN CONNECTOR LOWER SUSTAIN CONTROL VIDEO DATA VIDEO DATA DATA DRIVER RIGHT DATA DRIVER CENTER 621 1 DATA DRIVER LEFT C 2 SUSTAIN CONTROL VIDEO DATA VIDEO DATA c26 c36 VIDEO DATA DRIVERS Slide 70 Circuit Explanation The D board consists of a Video Panel Control circuit a Discharge Control circuit and a Microp
35. nged use without rest periods Use only the 3D Eyewear recommended for this TV Slide 21 3D Eyewear Specification Liquid Crystal Shutter Frame sequential type Coin shaped lithium battery CR2032 Approx 75 hours in a row 177 x 46 x 174 mm 7 0 x 1 9 x 6 9 DC 3 V Main body Resin Lens section Liquid crystal glass Approx 63 g 2 2 ozs Transmitter for 3D Eyewear Within 3 2 m 10 5 from front surface Within 35 degree horizontal 20 bat vertical 0 C 40 82 F 104 F The location of the 3D Eyewear transmitter differs depending on the model of television There are differences in the viewing range of the 3D Eyewear among individuals Infra red receiver Receives infra red signals from the television The liquid crystal shutter open close timing is controlled by receiving infra red signals from the television which provide 3D expression of the images Slide 22 Image for left eye Vision principle with 3D glasses Image for right eye Brain recognizes the 3D stereopsis vision according to parallaxes of right and left eyes Composite image Slide 23 Difference Between the Passive Plastic Glasses With Polarized Lenses Used at the Movies and The Active Shutter System Glasses Used with 3D TVs With active shutter glasses crosstalk is eliminated easier than passive glasses Crosstalk is a phenomenon where an image intended for one eye is seen by the other causing gh
36. nt tests to determine elf the exact same brightness and color are displayed at all screen locations elf black levels satisfy standard criteria Panasonic 3D Plasma TVs meets the high standards set by the THX Certified Display Program Ps in mam 14 m Evaluation Points for THX Certified Displays Luminance Gamma Scaling video signal processing Contrast Uniformity Deinterlacing Colour gamut Max resolution Motion video conversion Slide 12 Contrast Ratio Note Native Contrast is expressed as a ratio of the minimum of luminance levels of blacks and the maximum of luminance levels of whites that are displayed and measured at the same time on the same screen in a dark room on a plasma panel module Panasonic s Native Contrast measurement expresses the maximum contrast ratio of the plasma panel measured at the time of manufacture and does not express a contrast ratio measured during ordinary viewing conditions by a consumer For 2010 plasma television models Panasonic measures Native Contrast in a Dynamic mode using a static white rectangular pattern with 496 area size This allows consumers to compare more easily the Native Contrast ratios reported for Panasonic plasma televisions with the Dynamic Contrast ratios reported by many manufacturers of LCD televisions Depending on the model Native Contrast of the panel has been measured as either 5 000 000 1 or 2 000 000 1 Unlike measurement
37. onic 3D Plasme x _ broadcasts in which 2D and 3D alongside each other to ensure a seamless simulcast to the receiver If signal is not processed as 3D the image on the TV will look like 2 pictures side by 8106 Used by Direct TV Top and Bottom Manual setting is necessary Blu ray do not support this format Checker Pattern Field Sequential In the field sequential method the screen is divided in clusters of pixels Because the images are laid out in a checkered pattern the image data that reaches each eye only has only half the number of pixels than that of a Full HD image thus resulting in a lower quality picture Line By Line In the line by line method the screen s lines are divided into even and odd lines by a polarizer filter This encodes the light in a plane that the odd lines can be only perceived by the left eye and the even only by the right eye Because the data for both eyes is displayed on one image the vertical resolution is only 50 96 of that of frame sequential technology resulting in a lower quality picture As well The polarizer filter with the polarizer glasses have limitations of its viewing angle when sitting higher or lower than the screen so called ghosting will appear olide 16 3D Display Formats Methods 3D Multiple Broadcasting FS Top amp Bottom Checker Pattern Frame Sequential Side by Side amp Also Called Line by Line Field Sequential HDMI
38. ost images to appear With the active shutter glasses both eyes can be closed off for a split second between each frame his reduces ghosting or crosstalk Passive glasses are used with TVs where a polarized filter in the TV has to switch directions for each eye Slide 24 Procedures To Check The 3D Eyewear Determining if a the 3D eyewear is working or not can be easily done if another set of working eyewear Is available When another set of eyewear is not available perform the following tests to determine if the glasses are OK 1 Battery voltage check 2 Shutter operation check 1 Battery voltage check e Normal charge 2 5V to 3V is indicated when the power switch is turned on and the Power LED turns on for approximately 2 seconds and then it goes off e Power LED blinks times when the power is turned off e low charge is indicated when the Power LED blinks for 5 times instead of just once after the power is turned on The voltage at this point is between 2V to 2 5V Note he IH receiving distance is shortened when the power supply voltage decreases e When the voltage drops below 2V the power doesn t turn on Replace the battery Slide 25 Procedures Check The 3D Eyewear 2 Shutter operation check Check shutter open close operation by changing 2D 3D select switch on the user menu The liquid crystal shutter open close timing is controlled by receiving IR signals from the TV which provide 3
39. ot disable the A board To completely disable the A board 1 Unplug the TV 2 Remove connectors P6 and from the power supply See note on previous slide 3 Plugin the TV Do not press the power button e TV partially turns on by itself e screen stays black e fan operation e The LEDs on the SS board and SC board are on To force the TV to display a white screen 1 Unplug the TV With P6 and P7 disconnected disconnect D5 from the from the D A board Plug in the TV Now the TV turns on by itself with a white screen ps uer iN olide 63 Helays Triggering Commands The AC relays in the power supply are triggered when the TV SUB ON command 3 2V is output from the A board Note The PANEL MAI N ON command 3 2V from the D board can also trigger the relays but since it s preceded by TV SUB ON it has not effect on the relays because by the time this command is output the relays are already energized signal Processing IC1100 Power 9003 Supply olide 64 er Method To Turn On the Panel Drive Circuit Only A Board is Isolated Power srTANDBY 5155 CIRCUIT 9801 2 1033 02 P15Vregz TT gloz 9003 P15V G Oivi IC9804 P2 5V Panel Drive Slide 65 Slide 66 oignal Process Block Diagram Q4537 OPTICAL AUDIO OUT A ARC one ARC_OFF 1C4500 TMDS DATA HOMI HDMI EQUALIZ
40. outputs the STB D3 3V and the reset pulse to the Panel CPU 1C9003 on the D board When the CPU on the D board is energized it outputs 2 commands PANEL MAIN ON e The POWER ON OFF The PANEL MAIN ON command turns on the power supply circuit that outputs the Vsus Vda 15V and 5V The POWER ON OFF command turns on the Video Panel Control and the Discharge Control circuits in the D board slide 61 Note Before following the procedure on the next slide make sure that connector P34 on the power supply has a jumper from pin 1 to pin 3 Some TVs may not have a jumper on P34 instead they have a jumper between pins 12 and 14 of connector P7 rre ff k Se 807MVH N 22 10 gt Ld SLA et Waaa u am rn NU es im 80 M T wt T 71 f imi Dec se pa wor ee P board with jumper on P34 nom Power Supply P board with jumper on P7 olide 62 er Method To Turn On the Panel Drive Circuit Only A Board is Isolated Its possible to have the Panel Drive Section running with the Signal Processing Section A board disconnected By separating the 2 sections it could be determined if the symptom on the TV is created by the A board or one of the boards on the Panel Drive Section Note Disconnecting D3 A32 and D5 A31 allows the TV to turn on by itself with a white screen after it is plugged in to the AC line This procedure does n
41. rect 3D image blue Normal 2D image non color Menu 3D Eyewear Menu Input format side bottom side bottom 3D Frame Sequential DIGA Side by side DirecTV Top 2 bottom 1 Displays image only when Side by Side ID is detected in the signal Devices compliant with HDMI v1 4 If ID is not detected image is displayed as Native image 2 Displays 3D image only when Top and Bottom ID is detected in signal Devices compliant with HDMI v1 4a If ID is not detected image is displayed as Native image olide 33 If you see something like this you need to change the TV s 3D input format to Side by Side powered by Panasonic How to change from 2D to 3D If you see something like this you need to change the TV s 3D input format to Top and Bottom t E 2 olide 35 How to change from 2D to 3D The best way to do this is on the remote press the VIERA TOOLS button on the remote T amp ART LIGHI SDCARU L INPUT 1117 EXIT MUTE FORMAT INFO FAVORITE olide 36 How to change from 2D to 3D After you press the VIERA TOOLS button this screen will come up Press the OK when the 3D option is highlighted ie Lei a VIERA CAST VIERA Link VIERA IMAGE VIEWER Media player z 6 slide 37 3D settings 3D Eyewear Left Right swap Diagonal line filter Safety precautions
42. rocessor Control circuit The right LVDS Low Voltage Differential Signaling signal from the A board is processed by the Video Panel Control circuit 169400 and the left LVDS is control by 109300 IC9400 output the video data to the data drive circuit boards C1 C2 C4 and C5 These boards output video data to the panel drive ICs that control the right side of the panel The Discharge Control circuit outputs the Control Data Sustain Data and Scan Control Data The Control Data is used by the Data Drive Circuit boards C3 and C6 boards to control the left side of the panel The Sustain Control Pulses are used by the Sustain board and the Scan Control Pulses are used by the Scan board Supply voltages P15V P5V and STBSV from the power supply are used to drive the circuits on the D board Other voltages 1 2V 2 5V and 3 3V derived from the P15V are used by the Video Panel Control IC IC9300 and the Video Panel Control Discharge Control IC 169400 71 Panasonic ideas for life de 71 Slide 72 Caution When Heconnecting Ribbon Cables Between C boards Its not save to reconnect any or all the ribbon cables between the C board if the TV has been energized while they re disconnected A residual voltage in the Vda line remains for a few minutes after the TV has been disconnected The panel can be damaged if there is a charge on the Vda line while the ribbon cables are been reconnected Warning Before reconnecting the ribbon cab
43. s created without the need for glasses but this is 10 to 15 years away Slide 18 Frame Sequential Method Frame Sequential Method Panasonic uses full HD sequential playback to achieve a level of reality that far exceeds conventional 3D systems Called the Frame Sequential Method it s the same method that is used in Hollywood s 3D films It reflects our commitment to 3D imaging detail Separate images recorded in 1920 x 1080 pixel resolution for both the left and right eyes are alternately displayed at the ultra high speed of 120 frames per second Viewing them with high precision 3D Eyewear produces 3D images in full HD quality Note The frame rate varies depending on the 3D image signal being reproduced For example 3D images are reproduced at 120 fps frames per second for a 60Hz input signal and 100 fps for a 50Hz input signal Slide 19 FULL HD 3D Video Picture Format FULL HD 2D Video Picture FULL HD Video Video of 60 frames of about 2 million pixels 1920 lines 1080line X60 frames second FULL HD 3D Video Picture FULL HD 3D Video Video of 60 frames for right eye and left eye total 120 frames of FULL HD Video 1920 x 1080 are alternately transmitted per second 1920 lines a x 1920 lines Z g F Full HD Full HD picture quality picture quality For left eye gt For right eye FULL HD 3D Video Two times of information data of FULL HD video pictures must b
44. s taken for previous models Pre Discharges do not occur for the images used in the 2010 model measurements so the results should not be compared to contrast ratios reported for earlier year Panasonic models Most manufacturers use the Dynamic Contrast methodology in measuring contrast ratios for LCD televisions This methodology unlike the Panasonic Native Contrast ratio measurement for plasma televisions compares the maximum luminance levels on full white signal in one picture with the minimum luminance levels on full black signal in another picture Slide 13 Precautions View the screen at a distance at least 3 times the height of the screen Recommended distance For a 50 inch TV 1 9 m 6 23359 or more For a 54 inch TV 2 0 m 6 56167 or more 2 When watching 3D movies take an appropriate length break after watching a movie m When watching 3D content on interactive devices such as games or computers take an appropriate length break after using for 30 60 minutes As a guide 3D Eyewear should not be used by children younger than 5 6 years old As it is difficult to judge younger children s reactions to fatigue or discomfort you may not prevent them from suddenly getting sick When this product is being used by a child the parent or guardian should check to ensure that the child s eyes are not becoming tired m When using the 3D Eyewear do not place breakable objects near the user The user may mista
45. y this voltage is not used by the D board In the A board the STB5V is applied to a 3 3V regulator 175480 to generate the STB3 3V to power the MAIN MICON Genx8 IC1100 The STB3 3V is also connected to the K board for remote control operation and to the power LED Not shown here olide 55 Turn On at Plug in Signal Processing gt Video Signal SS 1100 2 A32 2 03 D25 JSTB5V AN 9004 CIRCUIT 9003 _ Panel 4 CPU _ Panel Dri Drive When the A board receives the STB5V at pin 1 of connector A7from the power supply it outputs the IV SUB ON command for approximately 15 seconds This command is applied to the power supply board to generate the F15V The F STB15V is applied to the A board The A board has a DC DC converter circuit that generates the SUB voltages used by signal processing circuit olide 56 Illustration of The Boards Being Temporarily Energized At Plug in This is an illustration of the boards being temporarily energized when AC is applied to the TV When the I V is plugged in for the first time the P A and K boards are energized for approximately 15 seconds olide 57 Power On Operation Signal Processing Video Signal CPU 1100 1 2V 3 3V ICS 00 5v Trv Ev 1 MIHO 3D Circuit E m DATA CIRCUIT Power supply
Download Pdf Manuals
Related Search