ekf 416 ud ekf 416 ud ekf 416 ud
Contents
1. at a height of at least 85 cm from the floor The bench or support must be able to support the weight of the machine and house it correctly The appliance contains electrical parts and must never be washed with a jet of water or steam The appliance is electrically connected before attempting any cleaning operation cut power to the appliance To prevent incorrect connection of the appliance the relevant electrical and water connections are marked by identification plates Do not use the door handle to move the appliance the glass panel may break When the tilting door is wide open do not use the internal surface to place objects to avoid damaging permanently the door hinges 7 How to use the control panel TECNOEKA Srl use and instruction manual ion 120 Fig 3 Fig 4 Fig 5 Programming cooking time To run the oven turn the programmer knob Fig 3 in line with symbol W continuous operation or in line with the selected cooking time up to 120 minutes In the second case end of cooking Is signalled by the oven switching OFF automatically Programming cooking temperature Turn the knob of the adjustment thermostat Fig 4 in line with the temperature selected for cooking Programming vapour quantity To generate vapour while the oven is in operation cooking compartment hot turn the knob of the automatic humidifier Fig 5 in line with the required value from 1 to 5 If you turn the knob to posi2. Machine Directive 2006 42 CE Directive on the general safety of products 2001 95 CE Directive on the restriction in the use of dangerous substances in electrical and electronic appliances 2011 65 CE Directive on waste from electrical and electronic appliances 2002 96 CE RAEE TECNOEKA Srl declares that the mentioned above products meet the CE 1907 2006 REACH Regulation Borgoricco 21 01 2015 CRISTINA LORA XASgg PRODOTTNI FORNNFORNO ELETTRICO LEka MANUALI D USO Forno Elettrico 40 60 90 LEka Lingua Inglese NUOVA GAMMA EHlnstruction manual EKF 411 UD EKF 416 UD EKF 464 UD EKF 464 UD 001 HT EKF 464 UD 002 HT GB rev 3 doc Electric Ovens rev 4 10 11 12 13 14 15 Index Technical service General warnings Technical specifications Instructions for the installer Use instructions for the user Residual risks for the user How to use the control panel Oven cooking Cooking advice Routine cleaning and maintenance Technical assistance Informations to the consumers Wiring layouts The Warranty Availability and supply of spare parts ___EKF 411 UD EKF 416 UD EKF 464 UD EKF 411 UD 001 EKF 464 UD 001 HT EKF 464 UD 002 HT TECNOEKA Srl use and instruction manual 1 Technical service A technical check up once or twice a year helps prolong the life of the appliance and guarantees better operation Make sure that assistance is carried out solely and exclusivel
3. The appliance must be connected to the electrical mains according to current legal regulations Before making the connection make sure of the following the voltage and frequency values of the power supply system match the values on the technical data plate affixed on the appliance the limiting valve and the system are able to support the appliance s load see the technical data plate the power supply system has an adequate earth connection according to current legal regulations aomnipolar switch with minimum between contacts aperture of 3 mm sized to the load and conforming to current legal regulations is titted between the appliance and the mains in the direct connection to the mains the omnipolar switch used for connection is easy to reach when the appliance is installed the yellow green earth wire is not interrupted by the switch the power supply when the appliance is operating must not deviate from the rated voltage value by 10 make sure that after inserting the power supply cord into the terminal block it does not come into contact with any of the cooking range s hot parts if the supply cable is damaged then it must be replaced by the manufacturer or by your technical support or by a qualified person to avoid any risk Connection to the water mains The appliance must be fed with softened drinking water with hardness from 0 5 F to 5 F it is obligatory to use a softener to reduce the formation of l
4. ame Win HHI HH HEN fn E mail info tecnoeka com rev 4 gt T gt O O U a O LA v Ses O k Kees YO o LI Z O O mn 2 M U LUJ S e C o O O O LA T gt Ms gt EKF 411 UD 001 EKF 464 UD 001 HT EKF 464 UD 002 HT f A USE AND INSTRUCTION MANUAL MODD EKF 411 UD EKF 416 UD EKF 464 UD ee E en CO Z STR ENTRY GI a S Re HH HHH HHR GC Pi fin EERE Tel 39 049 9300344 39 049 5791479 Fax 39 049 5794387 TECNOEKA SRL VIA MARCO POLO 11 35010 BORGORICCO PADOVA ITALY TEL 39 049 5791479 39 049 9300344 FAX 39 049 5794387 E MAIL INFO TECNOEKA COM WWW TECNOEKA COM WWW TECNOEKA RU COD FISC P IVA 00747580280 REA N 133205 CAP SOC EURO 119 000 00 I V CE DECLARATION OF CONFORMITY Annexed document II A of directive 2006 42 EC Model EKF 411 UD EKF 416 UD EKF 464 UD EKF 411 UD 001 EKF 464 UD 001 HT EKF 464 UD 002 HT TECNOEKA Srl declares that the mentioned above products meet the following safety regulations Low voltage directive 2006 95 CE Electromagnetic compatibility Directive 2004 108 CE TECNOEKA Srl declares that the mentioned above products meet the following harmonised standards CEI EN 60335 1 CEI EN 60335 2 42 CEI EN 55014 1 CEI EN 61000 3 2 CEI EN 61000 3 3 CEI EN 62233 TECNOEKA Srl declares that the mentioned above products meet the following directives
5. and according to current legal regulations Any operation must be performed with electrical power cut to the appliance Before using the appliance carefully remove the special adhesive film protecting the parts in stainless steel Do not leave any glue residues on the surfaces If necessary remove them at once with an appropriate solvent Fitting the feet The feet are inside the appliance and must be secured on the four threaded holes on the base If necessary the height of the feet can be adjusted by screwing or unscrewing Positioning Position the appliance perfectly horizontally on a table or similar support the table or support must be at least 85 cm above the floor Position it at a distance of not less than 10 cm from the side and rear walls to enable natural ventilating air to circulate freely around it The appliance is ventilated through specitic openings on the metal walls of the outer housing and ensures efficiency and long life For this reason it is strictly forbidden to obstruct these ventilation openings even partially or for short periods Failure to observe this specific prohibition releases the manufacturer of the appliance from all responsibility and immediately voids any guarantee rights for the said appliance because its constructive conformity has been voluntarily compromised Furthermore the appliance is not suitable for embedding and Tor grouped positioning with other identical appliances Electrical connection
6. e with direct water jets because If any water enters it could limit the machine s safety Before doing any maintenance or cleaning jobs disconnect the appliance Trom the electrical mains and allow it to cool When the tilting door is wide open do not put anything on the surface because the door hinges could be irreparably damaged Do not attempt to carry out the periodic controls or any repairs by yourself Contact the nearest Service Centre and use only original spare parts N B Improper or incorrect use and failure to observe the installation instructions shall release the manufacture from all responsibility In this connection the directives in the POSITIONING paragraph must be strictly observed 3 Technical specifications Grill heating element kw O S Max absorbed poweri TI I Power cable oe 3x4 mm Typeofcable HORN F Connecting electric cable P Class e Degree aaa protection against humidity ta Water pressure kPa 100 200 The noise level of the appliance in operation is below 70 dB A The technical data plate is positioned on the rear panel of the appliance Electric Ovens rev 4 e EKE 411 UD EKF 416 UD EKF 464 UD EKF 411 UD 001 EKF 464 UD 001 HT EKF 464 UD 002 HT 4 Instructions for the installer The following instructions are aimed at the qualified installer to ensure that he carries out the installation adjustment and maintenance operations as correctly as possible
7. emperature and the humiditier know the desired steam quantity Defreezing Operate the oven and turn the thermo state knob and the humidifier knob in correspondence of position OFF e 9 Cooking advice Convection cooking Heat is transferred to the foods by pre heated air forced to circulate by in the cooking chamber The heat quickly and uniformly reaches all parts of the chamber enabling simultaneous cooking of different types of food providing they have the same cooking temperature placed on the shelves without mixing tastes and smells Convection cooking is page 8 Electric Ovens rev A EKF 411 UD EKF 416 UD EKF 464 UD EKF 411 UD 001 EKF 464 UD 001 HT EKF 464 UD 002 HT particularly convenient for rapid defreezing and for sterilising preserves and drying mushrooms and fruit Cooking desserts Desserts require a very high temperature usually from 150 to 200 C and a pre heated oven about ten minutes The oven door must not be opened until at least 3 4 of the cooking time has elapsed Whipped dough must be difficult to detach from a spoon because excessive fluidity would prolong cooking time to no avail Cooking meat Meat to be cooked should weight at least 1 Kg to prevent it drying too much Very tender red meats to be cooked rare which must be cooked on the outside to keep all their gravy require short cooking time at high temperature 200 250 C The gravy ingredients must be placed immediately in the pan on
8. f water enters this could limit the appliance s safety Do not use corrosive substances e g hydrochloric acid to clean the oven s support bench Cleaning the oven It is good practice to clean the oven interior at the end of every day of duty In this way it will be easier to remove cooking residues preventing them from burning when the oven Is next used Clean it accurately with hot water and soap or with the appropriate oft the shelf products Cleaning the oven door To clean the oven door thoroughly proceed as follows fully open the door insert the equipped plugs in the A holes on the hinges Fig 6 lift the door gently and withdraw it Fig 7 put back the door In the initial position by operating inverserly page 9 TECNOEKA Srl use and instruction manual Replacing oven lamp Electrically switch off the appliance unscrew the protective glass cap remove the faulty halogen lamp and insert the new one by using paper or cloth to not touch the lamp with bare hands Please note that the new halogen lamp must have the same characteristics as the one removed Put back the lamp cover with the gaskets and turn on the electricity 11 Technical assistance Before leaving the factory the appliance was completely regulated and tested by expert specialised personnel to guarantee the best operating results All repairs and settings must be performed with utmost care and attention respecting national safety reg
9. he product in light of the instructions given in the user s handbook supplied with the product 5 use of the product for uses different from the one for which it was built or anyway in a manner not compliant with the instructions given in the user s handbook supplied with the product 6 tampering with the product 7 adjustments and or maintenance and or repairs carried out by unauthorised personnel and or with non original spare parts 8 inadequate or careless maintenance of the product in contrast with the user s handbook supplied with the product 9 damages caused by fire natural disasters and accident as well as by any cause not attributable to TECNOEKA SRL In addition painted or enamelled parts knobs handles mobile or removal plastic parts light globes glass parts refractory stones electronic parts and any accessory parts and transport from the consumers final user and or purchases location to Tecnoeka srl and vice versa are excluded from the warranty Replacement costs of the oven and relative installation expenses are also excluded from the warranty TECNOEKA SRL cannot be held responsible for any damages either direct or indirect caused by the product breaking down or following its non use Any repairs carried out during the warranty do not cause said warranty to be extended or renewed Nobody is authorised to modify the terms and conditions of the warranty or to issue new verbal or written warranties Any dispute
10. ime inside the cooking chamber and pressure in the range trom 100 to 200 kPa 1 0 2 0 bar Connection to the water mains should be made through the threaded 3 4 solenoid valve on the rear on the bottom of the appliance fitting in between a mechanical filter and an on of tap before you connect the filter allow a certain quantity of water to flow out In order to drain any waste from the pipe TECNOEKA Srl use and instruction manual Water drainage A drain pipe see Fig 1 comes out trom the rear of the appliance to drain the oven cavity This pipe must be connected up to a pipe made to resist steam temperatures 90 C 100 C with an internal diameter of 30 mm DN 30 To prevent choking it is best to use a rigid pipe and make sure there are no elbow bends anywhere along the drain line Furthermore the drain line must slope down minimum slope 5 along its full length the length in question is from the appliance s drain pipe to the drain point and must not exceed 2 metres The drain line must run into an open floor drain Fig 2 In addition there must be a Tree air gap of at least 25 mm distance between the drain line coming trom the appliance and the funnel on the drain standpipe Whatever the case in order to comply with current hygiene Standards the line connected to the appliance s drain pipe must not come into direct contact with the drain point It is advisable to include a suitable trap in the line connecting the applia
11. ly if the cooking temperature is brief otherwise they should be added during the last half hour You can check the degree of cooking by squashing the meat with a spoon if the meat does not yield it is correctly cooked For roast beef and fillet which must remain pink inside cooking time must be very brief Meats may be placed on a plate Suitable Tor oven cooking or directly on the grill under which you should place a tray to collect the gravy When cooking has finished we advise you to wait for 15 minutes before cutting the meat so that the gravy does not come out Before being served the dishes may be kept hot in the oven at minimum temperature 10 Routine cleaning and maintenance WARNING Cut power to the appliance before every operation General cleaning Clean the oven when it is cold Wash enamelled parts with lukewarm water and soap do not use abrasive products steel wool or acids which could ruin them To clean the steel parts do not use products containing chlorine sodium hypochlorite hydrochloric acid etc even if diluted Use specific off the shelf products or a little hot vinegar Rinse thoroughly with water and dry with a soft cloth Clean the glass door of the oven with hot water only and do not use rough cloths Do not allow foods especially acid foods such as salt vinegar lemon etc to Stagnate on the stainless steel parts because they could deteriorate Do not wash the appliance with direct jets of water because i
12. manually reset safety thermal breaker It protects against excessive dangerous over temperatures which could be accidentally generated inside the appliance This device is located on the back of the oven 5 Use instructions for the user For first use we advise you to let the appliance to run load free at maximum temperature for about one hour In this way any unpleasant smells due to thermal insulation and residual work grease are eliminated This appliance must be used solely for the purpose for which it was expressly designed i e cooking foods in the oven Any other use is considered unsuitable The appliance can be used for all oven cooking of deserts pizzas meat fish vegetables as well as for gratinating and for re conditioning cooled and frozen foods When placing food in the cooking compartment leave a space of at least 40 mm between pans in order not to over obstruct air circulation Do not use pans with higher than necessary edges edges are barriers which prevent the circulation of hot air Warm up the oven before every cooking operation to obtain maximum uniformity Do not salt foods in the cooking compartment 6 Residual risks for the user After a cooking operation open the door cautiously to avoid a violent outflow of heat which could cause burns While the oven is in operation pay attention to the hot zones marked on the appliance of its external surfaces Place the machine on a bench or similar support
13. nce s drain outlet to the grey water waste system thus stopping the steam coming back out of the drain max 000mm max 2000mm FIG 1 FIG 2 Connecting the power cable To access the terminal board just remove the appliance s rear side panel Loosen the cable gripper and allow the cable to pass through It Arrange the conductors so that the earth conductor Is the last to detach from its terminal if the cable goes into a state of faulty traction Connect the phase conductors to the terminals marked L1 and L2 connecting the neutral conductor to the terminal marked N and the earth conductor to the terminal marked with the symbol according to the following lay out 220 230 V AC 380 400 V 2N AC this electrical connection lay out is located near the power supply terminal board Tighten the cable gripper and reit the rear side panel of the appliance The appliance must be connected to an equipotential system whose efficiency must first be checked according to current legal regulations Electric Ovens rev 4 0 gt gt SS o EKF 411 UD EKF 416 UD EKF 464 UD EKF 411 UD 001 EKF 464 UD 001 HT EKF 464 UD 002 HT This connection must be made between different appliances by using the appropriate terminal marked with the symbol The equipotential conductor must have a minimum diameter of 2 5 mm The equipotential terminal is at the rear of the appliance Safety thermal breaker The appliance has a
14. ntilator Capacitors Operating direction reversing element Contactors coil Programmer indicator light Thermostat indicator light Humidity indicator light TECNOEKA Srl use and instruction manual 14 The Warranty Your appliance is covered by warranty The seller will replace or repair and his decision will be final free of charge for the customer only those parts that are defective due to a manufacturing fault on condition that under penalty of forfeiture for domestic equipment the customer notifies the fault within two months from the date when he she discovered it and anyway within 2 years form the date of purchase for professional equipment the customer notifies the fault within 8 days from the date when he she discovered it and anyway within 12 months from the date of purchase enclosing a copy of the invoice or receipt proving the purchase Apart trom the case when the customer cannot produce the invoice or receipt proving the purchase or when the above mentioned terms are not complied with the warranty is expressly excluded in the following cases 1 faults or breakage caused by the transport 2 wrong or incorrect installation of the product for instance because of insufficient draught of the flue or exhausts in light of the instructions given in the user s handbook supplied with the product 3 inadequate or abnormal electrical hydraulic and or gas supplies carelessness negligence or incompetence in using t
15. shall be settled by the competent Court in Padua Warning for the Buyer 1 the cooking appliance is designed only Tor cooking purposes while the heating appliance is designed only for heating domestic environments 2 TECNOEKA S r l does not install the appliances the seller shall be responsible for any installation carried out 3 TECNOEKA S r l cannot be held responsible for any damages either direct or indirect to people pets or property caused by the appliance breaking down or following its non use The Manufacturer cannot be held responsible for any inaccuracies due to misprints or mistakes in copying in this handbook The Manufacturer reserves the right to modity the products as he deems Tit also in the interest of the user without affecting the vital characteristics of functionality and safety 15 Availability and supply of spare parts TECNOEKA SRL keeps and ensures the availability of spare parts for a maximum of 24 months from the date of the sales invoice of the finished product to the dealer Availability cannot be guaranteed after said period page 12
16. tion e OFF the humidifier will stop operating Control thermostat indicator light The control thermostat orange indicator light goes OFF whenever the programmed temperature is reached inside the cooking compartment It lights up again when the thermostat Is tripped to re establish this temperature Automatic humidifier indicator light The orange indicator light of the automatic humidifier indicates that the water solenoid valve is operating and therefore vapour is being produced in the cooking compartment End of cooking programmer indicator light The programmer green indicator light indicate that the oven is operating and that cooking time Is active Oven internal light The light is always on when the oven is operating To switch off the oven Turn OFF the knobs of the end of cooking programmer and of the thermostat When you have finished using the oven shut off the water ON OFF tap upstream of the appliance and cut out electric power 8 Oven cooking For cooking betore putting food in warm up the oven to the required temperature When the oven reaches the temperature put the food in and check cooking time Switch off the oven 5 minutes before the theoretical time in order to recover stored heat Convection cooking Activate the oven and turn the thermostat knob in line with the required temperature Convection cooking steam dry heat wet heat Operate the oven and turn the thermo state knob to the desired t
17. ulations in force Always contact your retailer or our nearest Service Centre giving details of the problem the appliance model and the serial number on the rating plate on the rear panel For any maintenance the user can contact Tecnoeka by calling the teleohone numbers on the cover or going to www tecnoeka com 12 Informations to the consumers Further to Directive 2002 96 EC the symbol of the crossed rubbish skip on the appliance means that at the end of its life the product must be disposed of separately from the other rubbish The user must hand the appliance to a specialised waste collection centre for electric and electronic equipment The separate collection of the rubbish and subsequent treatment recovery and disposal help to produce other equipment using recycled materials reducing the negative effects on the environment and public health which would be caused by incorrect management of the rubbish Should the user dispose of the product abusively administrative sanctions would be applied Electric Ovens rev 4 13 Wiring layouts KSM EKF 411 UD EKF 416 UD EKF 464 UD EKF 411 UD 001 EKF 464 UD 001 HT EKF 464 UD 002 HT M Power terminal board Pr End of cooking programmer MI Door microswitch T1 Safety thermostat T2 Control thermostat R1 R2 Circular heating elements E Humidifier solenoid valve U Humidifier switch L1 Lighting lamp Radial motoventilators Tangential motorised ve
18. y by qualitied personnel For any spare parts orders or for any Information about the appliance always mention the serial number and model data indicated on the technical data plate at the rear of the oven 2 General warnings Very important keep this instruction book together with the appliance for future consultation These warnings were drafted for your safety and for that of others Please read them carefully before installing or using the appliance If on receipt of the goods the packaging is damaged write the following on the delivery note REVERSE THE RIGHT TO CONTROL THE GOODS specify the damage and get the driver to sign In acceptance send a claim in writing to the seller within 4 calendar days trom the date of receipt No claim shall be accepted after such period The warehouse inside temperature must not be lower than 9 C otherwise the thermostat regulation and safety thermostat control devices of the machine will be damaged Failure to observe this prohibition invalidates any responsibility of the manufacturer of the machine The appliance is intended for professional use and must be utilised by qualified personnel trained to use it Any moditication which may be necessary on the electrical system to enable installation of the appliance must be carried out solely by competent personnel tis dangerous to modify or attempt to modify the characteristics of this appliance Never clean the applianc
Download Pdf Manuals
Related Search