dsu iq quick start guide
Contents
1. PASSWORD 8 PREVIOUS 3 DISABLE 2 IP ADDRESS 9 ADD 3 SUBNET MASK 1TERMINAL 10 DELETE 1 TRAP MANAGER DLCI 3 SYSTEM 4 GATEWAY IP ADDRESS 2 SLIP PROTOCOL 2 TRAP MANAGER IP ADDRESS 1NONE 5 CONTROL PORT OPTIONS 3 PPP PROTOCOL 3 TRAP MANAGER PORT 2 DTE PORT 6 READ COMMUNITY NAME 4 NEXT 3 NETWORK PORT 7 WRITE COMMUNITY NAME 5 PREVIOUS 4 CONTROL PORT 8 TRAP MGR OPTIONS 6 ADD 5 ETHERNET PORT 7 DELETE 9 PROTOCOL 1 1NONE 1 DTE PORT 10 PROTOCOL2 2IP 2 NETWORK PORT 31PX 3 LAYER 3 STATS 11 SYSTEM TIME 15 MINUTES 4 ARP 4 TOP TALKERS 12 SYSTEM DATE 2 10 MINUTES 5SNA 2 VIEW STATISTICS 5 DLCILIST 13 HISTORY INTERVAL SIZE 3 15 MINUTES 6 UNKNOWN 6 SYSTEM 4 20 MINUTES 7 RESET STATISTICS 5 30 MINUTES 3TEST 1PING 1PING ADDRESS 2 START PING 1 DLCI 2 PVC LOOPBACK 2 TEST LEN MIN lt O UNTIMED gt 3 START TEST 4 STOP TEST 14 LOGOUT 5 VIEW TEST 6 RESET TEST STATS 7 VIEW DLCILIST These options are only available when the Ethernet card is installed Ifa Dial Backup DBU card is installed refer to the DSU IQ User Manual for a menu tree of the related DBU and Dialing configuration options DSU IQ Quick Start Guide 61200212L1 13A ApiRan2. C CONFIG and the Management Options CONFIG gt SYSTEM as desired for your application Troubleshooting Unit not in sync with DDS 1 Ensure that the timing source is correct By default the DSU IQ derives timing from the network CONFIG gt NETWORK PORT gt PHYS LYR OPT gt CLOCK SOURCE The factory default setting for the network loop rate is AUTO Setting the unit to 56K or 64K to match the network connection may correct the problem CONFIG gt NETWORK PORT gt PHYS LYR OPT gt LOOP RATE Network Signaling State is down The factory default setting for the signaling type is AUTO Setting the unit to the expected PVC signaling format may correct the problem CONFIG gt NETWORK PORT gt FR OPT gt SIGNAL Testing To verify data integrity across the frame relay network perform a PVC loopback test for each PVC TEST gt PVC LOOPBACK This test is non intrusive and can be performed on all PVCs or on an individual PVC ApiRan DSU IQ Quick Start Guide Front Panel Keys Enter Selects the active menu item Arrows Scroll through and activate the menu items of the current menu The flashing cursor indicates the active parameter Cancel Stops current activity and returns to previous menu Numeric Keypad Activates menu items and enters numeric informa tion Next Prev Add and Delete For use when editing tables such as the PVC Options table You must press and release the Shift key first to activate th
3. DSU IQ QUICK START GUIDE Installation and Configuration Plug in AC power press and hold the Quick key and turn unit on This sets the unit to the factory default settings If a problem is detected during Self Test contact ADTRAN Technical Support Activate menu item selections either by pressing the corresponding number if applicable on the keypad or by scrolling to the selection using the arrow keys The cursor will flash on the first character of the activated selection Press Enter to select the activated menu item See the Front Panel Keys section in the right column of this page for more guidelines on using the front panel interface Using a 4 wire telco cable connect the DSU IQ s telco connector to the telco jack The unit should establish synchronization with the DDS network Verify synchronization by viewing the DSU Loop State STATS gt NETWORK PORT gt DSU LOOP STATE If this field displays a message other than 56K or 64K NORMAL refer to the Troubleshooting section below Connect unit to a router using either an EIA 232 or V 35 cable If EIA 232 is used select E A 232 as the Interface Type CONFIG gt DTE PORT gt PHYS LAYER gt INTERFACE EIA 232 The DSU IQ should be exchanging frame relay PVC signaling messages with the network If the Signaling State STATS gt NETWORK PORT gt SIGNAL STATE displays DOWN after one minute see the Troubleshooting section below Configure the PVC Options CONFIG gt NETWORK PORT gt PV
4. ese keys Quick Resets the unit to factory default settings To reset press and hold this key when turning the DSU IQ power on When defaults are successfully loaded the unit name displayed in the LCD is followed by an exclamation point ADRAN 901 Explorer Boulevard P O Box 140000 Huntsville AL 35814 4000 Technical Support 888 4ADTRAN 1999 ADTRAN Inc All rights reserved Printed in USA 61200212L1 13A 1DTE PORT 2 NETWORK PORT DSU IQ TERMINAL MENU TREE 1 PHYSICAL LAYER 2 FRAME RELAY OPTIONS 4 MANAGEMENT DLCI 5 MANAGEMENT PVC OPTION 6 SIGNALING RESPONSES 1ENABLED 2 DISABLED 1PHYSICAL LAYER OPTIONS 1LOOPRATE 2 CLOCK SOURCE 1INTERFACE TYPE 2 TD CLOCK SOURCE 3 FLOW CONTROL 1EIA 232 2V 35 1 INTERNAL 2 EXTERNAL 1 NONE 2 HARDWARE 3 FECN BECN 4 CTS OPTION 1 FORCED ON 1ALWAYS ON 2 FOLLOW RTS 2 FOLLOW NETWORK 5 DSR OPTION 1 FORCED ON 156K 6 CD OPTION 2 NORMAL 264K 3 AUTO 1 SIGNAL TYPE 1 NONE INTERNAL 2 LMI 2 FROM NETWORK 3 ANSIT1 617 D 2 FRAME RELAY OPTIONS 4 ITU T Q 933 A 1 CONFIGURATION 3 MANAGEMENT DLCI1 5 AUTO 4 MANAGEMENT DLCI 2 1DLCI 5 MANAGEMENT DLCI 1 MODE 1SHARED 2 DBUDLCI 6 MANAGEMENT DLCI2 MODE 2 DEDICATED 3 CIR Kbps 7 MAX PVC COUNT 4 SEQ NUM CHECKING 1DISABLED 8 HISTORY INTERVAL COUNT 5 DELAY MEASUREMENT 2 ENABLED 9 PVC OPTIONS 6 STATS OPTION 1 AUTO 7 NEXT 2 ENABLE 1 CHANGE
Download Pdf Manuals
Related Search