DV-2000MT - Mackenzie Laboratories, Inc
Contents
1. Message On Hold input Connect the other side of this cable to the DV 2000MT s LINE OUT There are two audio outputs on the DV 2000MT LINE OUT Low 4dB into 600 ohms and SPKR OUT High 1W into 8 ohms Use the LINE OUT first adjusting the audio output volume potentiometer to obtain the correct audio level If this does not provide enough audio level then switch to the SPKR OUT 2 4 Connection to the PA equipment 1 Connect one side of the supplied RCA RCA cable to the PA amplifier s line level input Connect the other side of this cable to the DV 2000MT s LINE OUT There are two Audio outputs on the DV 2000MT LINE OUT Low 4dB into 600 ohms and SPKR OUT High 1W into 8 ohms Use the LINE OUT first adjusting the audio output volume potentiometer to obtain the correct audio level If this does not provide enough audio level then switch to the SPKR OUT ca o 0 D o L ome A ge 2 E m ee ro WW N Q fi ye E SS peso sy l ol l i A i z USE LINE CONNECTION 1 FIRST IF LEVEL IS TO 120VAC TOO LOW SWITCH TO 80 2 CONNECTION 60 Hz AUDIO OUTPUT TO MESSAGE FROM BGM ON HOLD INPUT OF TELEPHONE source A ME Swatchine EQUIPMENT OR INPUT OF PUBLIC ADDRESS SYSTEM 3 Operation 3 1 Message Downloading When you receive the new DV 2000MT Storecasting system its memory will be bl2. prior to a pre recorded message play 3 3 Manual message playback A manual Start control input is provided on the Remote connector of the DV 2000MT The user initiates manual message playback by shorting the two control pins provided on the Remote connector together When the system is in manual playback mode the Audio LED will only light when the DV 2000MT is playing a pre recorded message When in this mode the system will only play messages when the Start input is activated by the user ignoring the delay time setting on the rotary switches The system plays the messages in the same order as they would be played in automatic mode One message is played per Start activation If the user issues another Start activation while a message is playing the DV 2000MT will stop the currently playing message and immediately start the next message If the Start activation is held active indefinitely the DV 2000MT will play messages sequentially with no pause time between them until the Start activation is removed When the Start activation is removed the system will finish playing the active message and then stop and await the next Start activation The user cannot stop a message once it has been started on the DV 2000MT To get out of manual activation mode deactivate and then activate the monitor speaker Note Even if you are in manual message playback mode a message download will configure the system for Automatic message playba
3. recorded message plays Music and Message Default This mode allows Pre recorded messages to be played sequentially based on the Music Interval setting When a message is playing the BGM audio will be mixed in with the pre recorded audio Between pre recorded message plays the BGM Audio will be routed directly to the audio output Speaker pushbutton Black locking A monitor speaker on the front side of the unit allows the local user to hear the Audio being output by the DV 2000MT Pressing this button will activate the monitor speaker Releasing the button will deactivate the monitor speaker The volume of the monitor speaker is determined by the volume setting of the Audio output If the phone system requires a particularly low level from the DV 2000MT the volume of the monitor speaker will also be low Note Do not adjust the Audio output level adjustment in order to hear the monitor speaker level better Doing this will adjust the level of the Audio output which may not be acceptable 3 5 LED Light Emitting Diodes descriptions Four LEDs are provided on the top of the DV 2000MT unit to display the current status of the system Eject LED Yellow This LED will light whenever the tape is ejected i e no tape in the system When a tape is inserted and loaded i e tape is completely inside the machine this LED will go out Record LED Red This LED will light when the DV 2000MT starts recording an Audio program and wil
4. turning the unit off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient the radio or TV receiving antenna Relocate the unit with respect to the radio or TV receiver or vice versa Plug the unit into a different outlet so that it and the radio or TV receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The silence portion between messages is not included in the maximum recording time The audio should be set to a nominal level of OVU 4dBm For best results the audio should be filtered to cutoff any frequencies higher than 3 4kHz for Table of Contents the STD version and 6 8kHz for the PRO version 1 OVERVIEW soe soos os sce cot oes A aus cate Sid saat S A 4 The dynamic range of the production should be held low so as to allow the production to be 1 1 Features and Benefits cece cccccccccssssssceecceeseseeeeeeeeseeeseeaaeeeeeeeeeeeaaas 4 recorded at the highest possible level without exceeding 5VU 1dBm 1 2 General Specifications eiten aee ae ae iaa aa E 4 e The system requires 6 seconds of constant audio at a level greater than 20dBm for the 2 Installation 5 system to acknowledge the production and start recording This is required so that the aS a Fi a Pa aae A ae A Eai E a aaa ra REE Ea system can discriminate between t
5. ANA nerap a P ATT Sn inga rewind the tape It will automatically start playing the ia E EA message s from the digital audio memory Enabled message If pressed during the recording process the recording will be stopped NO TAPE LED Yellow light ON indicates there is no cassette inserted Yellow light OFF indicates the cassette is in place RECORD LED Used to determine tape loading mode Red light ON indicates message s is being loaded into memory PLAYING LED This green LED is ON when the system is playing a Pre Recorded message SPEAKER PUSH BUTTON Turns local Monitor ON OFF aHa enero APHEX MIX AUXILIARY REMOTE CONNECTOR PLAY MODE SWITCH pplee p pier Adjusts the amount of high frequency Used for external remote control UP music only enhancement necessary to deliver the best 1 3 applications where single step or play on MID music amp message BGM LEVEL overall system performance command is required Contact activation DOWN message only Adjusts level of external music source UDIO OUTROr UNE 1 6 Relay output 2 5 and Audio line 3 4 d gt 5 MUSIC INTERVAL BGM INPUT Audio output level of up to 4 into 600 0 MONITOR SPEAKER MINUTE SECOND SWITCH Select Connect to external source of music this is a standard level far most applications 14 Allows user to preview message between minute or second mode recording and play back TENS AND ONES ROTARY To set musical interval AUDI TPUT POWER A The Mac
6. Return Address MACKENZIE LABORATORIES INC 1163 Nicole Court Glendora CA 91740 USA OTHER MACKENZIE PRODUCT LINES Digital Message Repeaters Mackenzie s line of Digital Message repeaters are the ideal audio announcement solutions for Public Address Amusement Entertainment Museum and Exhibit applications Self contained solid state systems offer unparalleled reliability A variety of channel connection bandwidth and memory configurations are available Controls and Peripherals Many applications require additional equipment to optimize the performance of Mackenzie products This area focuses on items developed or sourced for their compatibility ease of use and value Included are input output controllers speakers amplifiers motion sensors and pushbuttons among others Transit Mackenzie is making a difference in transit applications with innovative solutions for ADA compliance and Passenger Information Systems These products address a variety of audio and text messaging requirements and support both in vehicle and wayside installations Overhead Page Management Mackenzie s OPM and FE series of Digital Page Stacker Repeater and Feedback Eliminators offer advanced features for the most difficult paging and intercom applications A unique design makes feedback virtually impossible by recording then repeating pages which opens the loop between the input microphone and speakers Various models are available to support simple repetit
7. ank To load new messages into the DV 2000MT s memory simply insert a pre recorded and properly formatted cassette tape into the DV 2000MT unit Make sure to insert the tape with the Audio side up When a new tape is inserted the DV 2000MT will automatically rewind the cassette to the beginning and start playing it The DV 2000MT will record the audio program s ignoring the silence segments on the cassette When the Audio program on the tape starts the red Record light will come on signifying that Audio is being recorded At the end of the Audio program when the DV 2000MT detects 6 seconds of silence the Record LED will go out The system will keep playing the tape while it looks for another message on the tape If another message exists the red Record light will go on signifying that another message is being recorded When the last message on the tape is recorded signified by 10 seconds of silence the system will automatically rewind the cassette tape 3 1 1 Message Download Mode 1 Replace All When this mode is used the system will erase all the messages in memory as soon as the tape is inserted The system will begin recording the messages from the cassette tape into memory starting from message 1 and continuing through the last message on the tape Use this mode any time all of the messages on the DV 2000MT system need to be updated Important Once a tape is inserted into the DV 2000MT system in this mode all of the m
8. ape noise and message material 2 1 all or ab e Installati n i neien aaia aa iiki 5 2 2 Connecting the power Pack cccceeeeeesseeeeeeeeeeeeeenceeeeeeeeeeeeeneeeeeeeeess 5 7 WARRANTY SERVICE amp RETURNS 2 3 Connection to Telephone EquipMent ccceeceeeeseeeeeeeeeeeeenteeeeeeeees 5 The industrial grade housing and quality construction of the Mackenzie DV 2000MT virtually 2 4 Connection to the PA equipment meia enana oa a nea aE 5 eliminates the need for service or maintenance There are no user serviceable components 3 Operation o n LEEEEEEEEEEEEEEEEEENEEESEEEntEEstEsettsetttetetenetetettnetetettteeeteeeneent 5 within the Mackenzie DV 2000MT Refer all servicing to the factory 3 1 Message Downloading ccccecceeeeeeeeeenneeeeeeeeeeeenaaaeeeeeeeeeeeeneeeeeeeeees 5 3 1 1 Message Download Mode 1 Replace All eeeeeeeeeeeeeeeeeeee 6 7 1 Warranty Coverage 3 2 Automatic message playback ccccccccccccccccceceeceeeeeeeeeeeeeeeeeseeseseees 6 The Mackenzie DV 2000MT is tested and checked before shipment and are guaranteed 3 3 Manual message playback cecceceseeeeteeeeeesteeeeeeeeeeeeteeteeeaeeeteeeaes 7 against defective material or workmanship for a period of three 3 year from the date of 3 4 Pushbutton GeSCriptionS cccccccccceceeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 7 purchase Should trouble ever develop contact the Factory directly by telephone or in w
9. attached to the DV 2000MT and the phone system Turn the output level adjustment clockwise to increase the Audio output level Use the 8 ohm output instead of the line level output Can t hear anything through the monitor speaker If both Record and M O H LEDs are off there are no recorded messages on the system Press the Speaker button so that it locks in the depressed position If the audio output is adjusted low the level from the monitor speaker will also be low The system didn t record all the messages on the tape If there is noise in the silence portions separating the messages on the cassette tape multiple messages can get grouped into a single message location on the system 6 Audio Tape Production Format MESSAGE 1 MESSAGE 2 MESSAGE 3 LAST MESSAGE TAPE SILENCE i SILENCE ih SILENCE i SILENCE A SILENCE TAPE START 6 9 SEC j 6 9 SEC yf 6 9 SEC y 6 9SEC W 9 11 SEC END Messages must be recorded on the left channel or track A The length of individual messages do not have to be the same but the total length of all messages should not exceed the total memory capacity of the unit Music Interval Two Rotary switches and a slide switch make up the Music Interval setting The two rotary switches allow for a setting from 00 to 99 The left rotary switch represents the tens position while the right rotary switch represents the ones position The slide switch to the right of the ro
10. ck After messages are downloaded the system will immediately begin playback The user must initiate manual message playback by shorting the two control pins of the Remote connector after a message download 3 4 Pushbutton descriptions Two pushbuttons are provided on the DV 2000MT system Eject Rec Stop pushbutton Red momentary Allows the user to stop the recording process in several ways and or eject the tape When the system is not recording the button functions as an Eject button When the DV 2000MT is recording audio whenever the Record LED is on pressing this button momentarily will stop the recording and save the Audio which was just recorded The system will rewind the tape but not eject it If this button is pressed and held for two seconds while the DV 2000MT is recording the message just recorded will be deleted and the tape will be ejected without being rewound If the button is pressed momentarily while the DV 2000MT is recording audio and then pressed momentarily again the system will stop the recording process save the Audio just recorded and eject the cassette tape without rewinding it Model DV 2000 MT amp DV 2000 MT PRO DIGITAL AUTOLOAD MESSAGE ON HOLD amp MUSIC THRU SYSTEM NOTE Insert Pre Recorded tape Cassette as shown Tape up Facing label system will rewind tape then start loading Red LED is on at the end of downloading the n message s the Red LED will turn off system will E
11. e Messages are digitized and stored in non volatile FLASH memory that protects them from loss during power outage The DV 2000MT supports up to 20 individual messages The Background Music BGM input is for combining messages with an external music source such as CD or satellite A built in timer lets the user determine the time between message plays Multiple audio outputs 6000hm 80hm with level control Aphex and high quality sampling allow the sound of the DV 2000MT to be optimized for almost any phone or public address system insuring that the message gets heard 1 2 General Specifications Power 12VDC Audio Fidelity 3 4kHz STD 6 8kHz PRO 60aB Signal to Noise BGM Input RCA mono 10K ohm Audio Outputs RCA mono 600 ohm RCA mono 1W 80hm Remote Trigger RJ 12 trigger relay audio out Manual Controls BGM level BGM fade level Aphex mix Output volume Eject Speaker Delay Switches Play mode Delay min sec Package Painted steel chassis Aphex Aphex Aural Exciter and AX are patented registered trademarks of Aphex Systems Ltd 5 Troubleshooting guide Before contacting the factory please review the following answers to some common problems No LEDs are active on the DV 2000MT When a tape is inserted and before audio is detected by the system all LEDs will be off Verify that the AC DC power adapter is plugged into non switched AC power outlet Verify that the power connector is plugged com
12. ered BGM Fade Down pushbutton Black momentary Pressing this button will increase the ducking amount or in other words lower the BGM audio being mixed in with the audio output when a pre recorded message is played Pressing the button one time will attenuate the BGM audio approximately 1dB If the button is pressed and held the BGM level will be lowered approximately 8dB per second BGM Fade Up pushbutton Black momentary Pressing this button will decrease the ducking amount or in other words increase the amount of BGM audio being mixed in with the audio output when a pre recorded message is played Pressing the button one time will raise the BGM audio approximately 1dB If the button is pressed and held the BGM level will be raised approximately 8dB per second 3 7 Slide Switch descriptions Several slide switches are provided on the top cover of the DV 2000MT These switches control the functions described below Play Mode The DV 2000MT system has three play modes Music Only Message Only and Music and Message A three position slide switch sets the mode of the system Music Only No pre recorded messages are played when the system is in this mode The system will simply route the BGM audio directly to the output Message Only Pre recorded messages will be played sequentially based on the Music Interval setting The BGM audio will be muted however No audio will be present on the audio output connector between pre
13. essages in memory will be deleted immediately Even if the tape is then ejected prior to recording any audio the DV 2000MT s memory will be empty 3 2 Automatic message playback After messages have been recorded into memory the DV 2000MT will automatically begin playing them through the audio outputs There is no control or user input required to initiate the playback The green Audio LED will light whenever the system is playing messages Messages will be played back sequentially The messages in memory are automatically played back sequentially with a user programmed delay time inserted between them This delay time is set using the two rotary switches on the top cover The rotary switches provide a range between 0 and 99 A slide switch to the right of the rotary switches allows the setting to be represented in seconds or in minutes BGM In This sets the overall level of the background music being fed into the DV 2000MT Turning this potentiometer counter clockwise will lower the BGM level Turning this potentiometer clockwise will raise the BGM level BGM Fade Two pushbuttons are provided on the top cover allowing the user to set the amount of ducking to be applied to the BGM audio when a pre recorded message is played by the system The BGM audio is mixed with the pre recorded message audio and this setting governs the amount of BGM audio being mixed Ducking is the amount which the BGM audio level is attenuated or low
14. etain your original packing material in the event that you need to ship your DV 2000MT system When sending your DV 2000MT system to the factory include your name address phone number proof of date of purchase and a description of the operating problem After repairing or replacing your DV 2000MT system we will ship it to your return address at no cost to you within the USA Repair or replacement of your DV 2000MT system at our factory is your exclusive remedy 7 3 What this warranty does not cover This warranty does not cover defects resulting from accidents damage while in transit to factory alterations unauthorized repairs failure to follow instructions misuse fire flood and acts of God 1 OVERVIEW The DV 2000MT is a versatile Message On Hold and Storecasting system The MT combines high quality audio playback background music and remote control features for use in even the most demanding applications 1 1 Features and Benefits The DV 2000MT is a highly reliable audio playback system specifically designed for Message On Hold and Storecasting applications The system allows music and marketing messages while clients are waiting on hold or in your retail location This heightens awareness and minimizes frustration thus increasing sales Message material is loaded into the system via a ruggedized electronically controlled cassette mechanism originally designed for automotive applications and providing years of reliable servic
15. install during lightning storm 11 Never touch un insulated wires or terminals unless the unit is disconnected from both power and Seller the rest of the phone system 12 Use Caution when installing or modifying configuration switches or control lines Address 13 Install in a protected location where no one can step on or trip over power and line cords 14 The unit must be securely attached to a wall board rack or table mounted s 15 Use correct power source Use only the power pack supplied City State ____ Zip Phone Fax Email CAUTIO N a f any wiring from the system leaves the premises Return warranty card via you must use proper electrical protectors FAX 909 394 9411 MAIL Address on reverse side ONLINE www macklabs com registration htm Regulations FCC Part 15 Radio Frequency Interference The DV 2000MT generates and uses radio frequency energy and if not installed and used in strict accordance with the manufacturer s instructions may cause interference to radio and television reception Unit complies with the limits for Class A devices in accordance with the specifications in Subpart J of Part 15 of the FCC Rules This testing is designed to provide reasonable protection against such interference However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by
16. ion multiple page stacking and multiple input channels MACKENZIE DV 2000MT Digital Autoload Storecaster amp Music Thru System User s Manual Version 1 0 Revised 10 21 2004 Doc 99 20 181 25 00 MACKENZIE LABORATORIES INC 1163 Nicole Court Glendora CA 91740 USA Tel 909 394 9007 Fax 909 394 9411 Email info macklabs com Web www macklabs com Warranty amp Registration Card for the General Safety Instructions DV 2000MT Digital Autoload Storecaster amp Music Thru System Always follow these basic safety precautions when using the system Date Serial No 1 Read carefully and understand all instructions 2 Follow all warnings and instructions marked on the product Purchaser 3 DO NOT block or cover ventilation slots and openings 4 DO NOT place the product in a closed enclosure or cabinet unless proper ventilation is provided i 5 Never spill liquid on the product or drop objects into the ventilation slots and openings Doing so Address may result in serious damage to the components 6 Repair or service must be performed by a factory authorized repair facility City State Zip 7 DO NOT staple or otherwise attach the power supply cord to building surface 8 DO NOT use the product near or in wet or damp places such as wet basements a 9 DO NOT use extension cord Install within 6 feet of a grounded outlet receptacle Phone Fax Em il 10 DO NOT
17. itor speaker Playing relay Pins 2 and 5 When in automatic playback mode these contacts will be closed continuously When recording they will be open When the system is in manual playback mode the contacts will only close when a pre recorded message is playing The contacts on the relay are rated at 24VDC at 1 amp non inductive load Audio output Pins 3 and 4 The line level audio output signal from the RCA connector is paralleled on these pins Note Even if you are in manual message playback mode a message download will configure the system for Automatic message playback After messages are downloaded the system will immediately begin playback The user must initiate manual message playback by shorting the two control pins of the Remote connector after a message download 4 Power failure recovery The DV 2000MT uses FLASH memory which is not dependent upon power or battery backup to retain its memory This eliminates problems associated with brown outs or unexpected power losses When power is returned the system will immediately start the operation it was in prior to power being removed 2 Installation This section provides complete instructions for mounting the DV 2000MT Before you install the DV 2000MT system make sure you have A message or music on hold input on your phone system or line level input to your public address system A non switchable 110VAC electrical outlet near the location where the unit is
18. kenzie Dynavox Aides oust otis up to into 8 ohm Use this between message playing Set the rotary switches to the DV 2000 MT amp MT PHO Quikey output if more drive is needed to reach a more BGM FADE UP DOWN PUSH BUTTON desired lime between 00 and 22 N TOTED 27 200 comfortable listening level 1 5 Adjusts the Amount the BGM input is Mackenzie Laboratories Inc ducked when a message is played 1163 Nicole CT Glendora CA 91740 USA ENEE TEL 909 394 9007 FAX 909 394 9411 aren Adjusts the volume to the line level www macklabs com or power audio outputs
19. l go out when the recording process stops The Record LED will blink one time when the DV 2000MT is powered on indicating that the memory operational M O H LED Green This LED will light whenever the DV 2000MT is in automatic playback mode and playing messages or outputting the BGM audio When the system is in manual playback mode this LED will light only when a pre recorded message is actually playing 3 6 Audio adjustments There are three potentiometers and two pushbuttons on the DV 2000MT system allowing the user to tailor the BGM level the audio output level and high frequency response These potentiometers are located on the front side of the device directly above the audio connectors Audio level The level of the both 600 and 8 ohm Audio outputs are simultaneously adjusted using the Audio level adjustment pot Turning this potentiometer counter clockwise will lower the Audio level Turning this potentiometer clockwise will raise the Audio level Aphex A special psycho acoustical processing extends the high frequency response of the DV 2000MT Turning this potentiometer clockwise amplifies the high frequencies while turning it counter clockwise attenuates the high frequencies In between pre recorded message plays the DV 2000MT will output the background music BGM audio to the audio output The DV 2000MT will gently fade the BGM audio up after a pre recorded message is played and it will gently fade the BGM audio down just
20. pletely into the jack on the DV 2000MT The system will not mechanically load the tape into the system Push the cassette tape completely into the DV 2000MT Verify that the AC DC power adapter is plugged into non switched AC power outlet Verify that the power connector is plugged completely into the jack on the DV 2000MT The system ejects the tape immediately after it is loaded The system will eject the tape immediately after loading it if the memory is full The system will eject the tape immediately after loading it if all of the messages are used The system will eject the tape immediately after loading it if it is an endless loop tape The Record LED never comes on after the cassette tape is loaded into the system Verify that the tape was inserted right side up If the tape is blank the Record LED will never come on Verify that the nominal level of the Audio recorded on the tape is over 20dB After recording the tape the tape ejected and the system is not playing a message Pressing and holding the edit eject button while recording will eject the tape immediately Verify that the tape was inserted right side up If there is no audio on the tape it will eject automatically when it reaches the end of the tape Can t hear anything from the audio output If both Record and M O H LEDs are off there is no audio being output by the system Verify that the RCA to RCA connector is securely
21. riting 3 5 LED Light Emitting Diodes descriptions ect tees e teens 10 If it is determined that the equipment requires Factory service return it to the Factory If our i h 2 3 6 Audio adjustments ccccccccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeseeeeeeeeeeeeeeeaaaaaaes 10 inspection shows that the trouble was caused by defective material or workmanship we will 37 Slide Switch d ipti 11 repair or replace the equipment without charge and return prepaid Repairs made necessary g ide wi CN GESCIIPUONS iias aa eisai ai aeeoa a ei by abuse improper use unauthorized service or maintenance and or improper installation as 3 8 COMMECTIONS sitiasion siestar beara t ea iroa te caeeeteeteesaecaseeteesesaeeeteetaes 12 i Power failure r COVETY e a a a re aa r rara re a a aeoea eaaa aeeai aien 12 Troubleshooting QUICE cccccccccceccceeceeeeeceeeeeeeeeeececeeeeeeeceeeeeeeeteeteeetetes 13 Audio Tape Production Format ccccccccccccccececceececeeeeceeeeeeeeeseeeeeeetess 13 well as out of warranty repairs will be charged at our regular repair prices in effect at the time The obligation under this warranty shall be limited to the replacement repair or refund of any such defective device within the warranty period NOOR This warranty is in lieu of and excludes all other warranties expressed or implied and in no WARRANTY SERVICE amp RETURNS csccccccceeeeseeeseeeeeeeeseeaeeeees 14 even
22. t shall MACKENZIE be responsible for dam age to other equipment or property for any 7 1 Warranty Coverage ME eS ie wee enh manera rat em arp wie cre wpa A E E are 14 anticipated profits consequential damages loss of item or other operation or use of this 7 2 What we ask you to dO ccccccccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 14 product and MACKENZIE S maximum liability shall not ever be greater than the price paid for 7 3 What this warranty does NOt COVES cccceeecceeeeeeeceeeeeeeteeeeseeeeeneeeeaes 14 the equipment This warranty gives you specific legal right Your rights may vary from state to state Inquiries regarding use repair and service should be made to Shipping Container Contents MACKENZIE LABORATORIES INC 1163 Nicole Court Glendora CA 91740 USA Telephone 909 394 9007 FAX No 909 394 9411 Email info macklabs com WWW www macklabs com The following items should be found in the container of the DV 2000MT Autoload Storecaster amp Music Thru System DV 2000MT System Power pack Audio cable Mounting hardware 7 2 What we ask you to do User s manual To get warranty service for your DV 2000MT system you must provide proof of the date of original purchase In the event you need to ship your DV 2000MT system to the factory for service call us for a return authorization number When you ship your DV 2000MT system you must prepay all shipping cost We suggest that you r
23. tary switches sets whether the 00 to 99 setting is in minutes or seconds These switches are read by the system during operation so changing the setting can be performed while the unit is playing messages 3 8 Connections 12VDC 2 5mm Barrel connector The system is powered by 12VDC Use only the AC DC power adapter supplied by the manufacturer to guarantee proper operation BGM IN RCA connector A 10K ohm transformer isolated audio input When installing the DV 2000MT system connect this input to the output of the background music source LINE OUT RCA connector A 600 ohm transformer isolated Audio output When installing the DV 2000MT system connect this output to the phone system first SPKR OUT RCA connector An amplified 1 watt into 8 ohm Audio output Use this Audio output if the Audio from the Line output can t drive the on hold circuit to a high enough level Remote RJ11 6 connector An auxiliary connector provides an alternative to interface to the DV 2000MT system This connector provides the line level audio output Start activation signal and a Normally open relay contact closure Start Activation signal Pins 1 and 6 Shorting these two pins together with a relay contact or a switch will put the system into manual playback mode When in manual playback mode the system will only play messages when a Start activation signal is received To get out of manual activation mode deactivate and then activate the mon
24. to be installed 2 1 Wall or Table Installation 1 Locate a proper space on the telephone equipment board or wall You can mount the DV 2000MT unit in one of three positions flat side or horizontal 2 Position the unit on the board mark the mounting hole locations 3 Using the mounting screws provided secure the DV 2000MT system to the board or wall 4 If table top mounting the DV 2000MT stick the enclosed rubber feet on the bottom of the unit O m 5 B cS c go O a FA GAL Auro ORDe TonECASTER E Msro THRU STEER Mounting Options 20 A Back of unit ERCAN against wall flat 10 x 8 o i D o be B Left side of unit RSA 5 fot ee i against wall side 2 2 x 8 3 a oas ae C Left side of unit TUTT U against wall horizontally 8 x 2 2 a N Q Q 2 2 Connecting the power pack 1 Plug the power pack into a 110VAC power outlet which is not connected to a switch 2 Plug the power plug into the DV 2000MT system s power jack marked POWER 3 There is no power switch on the DV 2000MT system so as soon as power is connected the system will be active 2 3 Connection to Telephone equipment 1 Connect one side of the supplied RCA cable to the telephone equipment s
Download Pdf Manuals
Related Search