Wireless Unit - starbike.com
Contents
1. INSTALLATION gt D Installation of the wireless unit Secure the electric wire to the frame CAUTION If the electric wire is too long it may interfere with the cassette sprocket or chain Use plastic tape etc to secure the slack electric wire to the frame 10 SHIMANG SHIMANO AMERICAN CORPORATION One Holland Irvine California 92618 U S A Phone 1 949 951 5003 SHIMANO EUROPE B V Industrieweg 24 8071 CT Nunspeet The Netherlands Phone 31 341 272222 SHIMANO INC 3 77 Oimatsu cho Sakai ku Sakai shi Osaka 590 8577 Japan Please note specifications are subject to change for improvement without notice English Jan 2014 by Shimano Inc HTR2. English DM WU0001 00 Dealer s Manual Wireless Unit SM EWWO01 IMPORTANT NOTICE IMPORTANT NOTICE e This dealer s manual is intended primarily for use by professional bicycle mechanics Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the dealer s manuals If any part of the information on the manual is unclear to you do not proceed with the installation Instead contact your place of purchase or a local bicycle dealer for their assistance e Make sure to read all instruction manuals included with the product e Do not disassemble or modify the product other than as stated in the information contained in this dealer s manual e All dealer s manuals and instruction manuals can be viewed on line on our website http si shimano com e Please observe the appropriate rules and regulations of the country state or region in which you conduct your business as a dealer For safety be sure to read this dealer s manual thoroughly before use and follow it for correct use The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment and surroundings The instructions are classified according to the degree of danger or damage which may occur if the product is used incorrectly AV DANGER Failure to follow the instructions will result in death or serious injury AV WARNING Failure to follow the in
3. avoid subjecting them to any strong shocks e Do not use thinners or similar substances to clean the products Such substances may damage the surfaces e Do not leave the product in an area exposed to strong sunlight for an extended period of time e Do not disassemble the product as it cannot be reassembled e When cleaning the product use a cloth moistened with a diluted neutral detergent e Contact the place of purchase for updates of the product software The most up to date information is available on the Shimano website e Products are not guaranteed against natural wear and deterioration from normal use and aging e For maximum performance we highly recommend Shimano lubricants and maintenance products Connection and communication with the PC PC linkage devices can be used to connect a PC to the bicycle system or components and an E tube Project can be used to carry out tasks such as customizing single components or the whole system and updating their firmware e PC linkage device SM PCE1 SM BCR2 e E tube Project the PC application e Firmware the software inside each component TO ENSURE SAFETY gt For Installation to the Bicycle and Maintenance W For Installation to the Bicycle and Maintenance NOTE e Always be sure to use the TL EW02 special tool to remove the electric wires e Be sure to use the specified electric wire e Secure the electric wires with plastic tape so that they do not interfere with the
4. the spacer and attach the spacer to the wireless unit Be careful about the orientation of the rubber sheet Attach it with its wider side facing the connector A ro A Wireless unit B Spacer at After attaching the rubber sheet hold down the entire surface with your finger for approximately 1 minute Temporarily fix the wireless unit to the frame with the fixing band Put the fixing band on one hook and pull the band to put it on the other hook C Frame D Fixing band E Hook Fix it at a height of 110 to 130 mm above the rear hub axle 110 130 mm CAUTION There is no guarantee that the wireless unit will be able to communicate normally if it is attached to the inside of the bicycle frame or anywhere other than to the seat stay at You need an additional electric wire 200 mm or longer to connect the wireless unit to the rear derailleur 3i To be continued on next page INSTALLATION gt D Installation of the wireless unit Disconnect the electric wire from the rear derailleur CAUTION Use the special tool TL EW02 for installation and removal of the electric wire Pass the electric wire through TL EW02 Set so that the projection on the connector is aligned with the groove on the narrow end F TL Ewo2 G Plug CAUTION When installing the electric wire do not forcib
5. chainrings sprockets and tires e The strength of the adhesive is fairly weak to prevent the paint on the frame from being peeled off at the same time when removing the double sided tape on the wireless unit for reasons such as replacing the electric wires If the double sided tape on the wireless unit peels off replace it with a new one When removing the double sided tape on the wireless unit do not peel it off too vigorously If this is not observed the paint on the frame will peel off too Notes when reinstalling and replacing components e When the product is reassembled or replaced it is automatically recognized by the system to allow operation according to the settings e If the component configuration changes or malfunction is observed use the E tube Project software to update the firmware of each component to the latest version and perform a check again Also make sure that the E tube Project software is the latest version If the software is not the latest version the component compatibility or the product functions may not be sufficiently available e When installing to the bicycle do not forcibly bend the electric wire plug It may result in a poor contact e After removing the wireless unit from the bicycle frame the double sided tape for the spacer may remain on the frame In that case wipe it off with a cleaner The actual product may differ from the illustration because this manual is intended chiefly to explain the proced
6. ly bend the plug It may result in a poor contact When connecting the electric wire push it in until it clicks in place Connect the following two electric wires to the wireless unit e Electric wire disconnected from the rear derailleur e Additional electric wire at Hold the wireless unit in your hand when connecting or disconnecting the electric wire from the wireless unit Connect the electric wire to the rear derailleur 3i To be continued on next page INSTALLATION gt D Installation of the wireless unit Check the excess length of the electric wire For a racing type rear derailleur push up the rear derailleur by hand until it touches the frame and check the electric wire while holding the rear derailleur in that position If the electric wire does not have enough slack make some fine adjustments to the height of the wireless unit Secure the wireless unit to the frame Remove the fixing band and use the double sided tape provided to attach the wireless unit to the frame CAUTION Make sure that the double sided tape is oriented correctly Attach it with the brown release liner facing the spacer and the white release liner facing the frame Fix it again with the fixing band CAUTION The wireless unit cannot be sufficiently secured without the use of the fixing band 3i To be continued on next page
7. structions could result in death or serious injury Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings TO ENSURE SAFETY PP Introduction TO ENSURE SAFETY E Introduction A WARNING e When installing components be sure to follow the instructions that are given in the instruction manuals It is recommended that you use only genuine Shimano parts If parts such as bolts and nuts become loose or damaged the bicycle may suddenly fall over which may cause serious injury In addition if adjustments are not carried out correctly problems may occur and the bicycle may suddenly fall over which may cause serious injury Be sure to wear safety glasses or goggles to protect your eyes while performing maintenance tasks such as replacing parts e After reading the dealer s manual thoroughly keep it in a safe place for later reference NOTE Be sure to also inform users of the following e This is a small waterproof connector Do not repeat connecting and disconnecting it It may impair the function e Be careful not to let water get into the terminal e The components are designed to be fully waterproofed to withstand wet weather riding conditions however do not deliberately place them into water e Do not clean the bicycle in a high pressure wash If water gets into any of the components operating problems or rusting may result e Handle the products carefully and
8. ures for using the product BEFORE INSTALLATION BEFORE INSTALLATION Compatible cycle computers A compatible cycle computer is required to use SM EWW01 For details refer to the manual for the cycle computer at For information on how to perform pairing refer to the user s manual The types of information displayed depend on the products Refer to the manual for your cycle computer Updating firmware For SM BMR1 SM BMR2 and SM BTR2 the following firmware versions are required Use SM PCE1 or SM BCR2 to update the firmware in E tube Project SM BMR1 Version 2 1 1 or later SM BMR2 Version 2 3 1 or later SM BTR2 Version 2 3 1 or later INSTALLATION INSTALLATION Shape and size of the frame A Wireless unit B Electric wire at Attach the wireless unit to the seat stay of the bicycle frame Installable circumference of the seat stay 40 mm 75mm A B CAUTION Even if the circumference is within the above range the wireless unit cannot be attached to a seat stay with a cross section that is much wider than the wireless unit INSTALLATION PP Installation of the wireless unit E Installation of the wireless unit Shift to the largest front chainring and to the smallest rear sprocket Wipe the dirt and dust off the frame and if the frame is wet dry it well before attaching Remove the release back sheet from
Download Pdf Manuals
Related Search