ENARCO, S.A.
Contents
1. STATIONARY RING 2000 950 ROWELS WITH ELECTRIC OR PETROL ENGINE 3 USAGE CONDITIONS N WARNING READ AND UNDERSTAND EVERY INSTRUCTION GENERAL INSTRUCTIONS Machine must be operated by reliable operators who read and understand the operation o manual of age above 18 Keep all unauthorized untrained people and children out of the working area while the trowel is in operation Keep your working area clean and well lit Cluttered benches and dark areas may cause A accidents Know your working area is necessary to know possible obstacles inclinations and underground utility lines Be observant of other workers bystanders and other machinery placed in the working area Before starting the work inspect the machine thoroughly check all safety devices indicators and controls Do not operate power tools in explosive atmospheres such as in the presence of flammable A liquids gases or dust Do not work with a petrol engine in closed or poorly ventilated areas Concentrated exhaust fumes are dangerous to health Never unattended the machine while the engine 15 running Keep children and visitors away while operating a power tool Never start the petrol engine in closed areas unless proper ventilation is ensured Do not abuse the cords Keep cords away from heat oil sharp edges or moving parts Replace damaged cords immediate2. GASOLINE 1000 1400 STATIONARY RING e qu 5 BLADES 1390 2000 2000 950 TROWELS WITH ELECTRIC OR PETROL ENGINE BLADE ADJUSTMENT MECHANISM STEERING ME 2100 LIFTING EYE SAFETY STOP SWITCH ENGINE CARRYING PIPE 2100 2 2 ELECTRIC MOTOR MODELS WEIGTH ELECTRIC DIMENSIONS MAXIMUM MOTOR LxWxH mm TORQUE rpm TIFON 600 E 65 kg 2 2 Kw TD 1400 x 650 x 1000 TIFON 900 E 80 kg 1 8 2 8 kW 2100 x 950 x 1040 SAFETY STOP SWITCH 600 E STEERING BLADE ADJUSTMENT MECHANISM GASOLINE 1400 STATIONARY RING BLADES 900 E X 7 BLADE ADJUSTMENT MECHANISM STEERING LIFTING EYE ELECTRIC MOTOR 2000
3. machine must stop working If the machine doesn t stop working check again the connections of the safety system TROWELS WITH ELECTRIC OR PETROL ENGINE
4. moving parts Use safety equipment and check all safety devices before start the engine TROWELS WITH ELECTRIC OR PETROL ENGINE Hold the machine firmly Pay extra attention when operating the machine at the edges of digs holes etc to avoid rolling over or falling down of the machine The operation of the machine may require walking backwards so be aware of the obstacles Stepping in or tripping over such obstacles will cause the operator to lose control of the machine and can result in injury Be sure that safety stop switch on your machine is working properly Ignition supply must be cut off at once in case of emergency Never disable or disconnect the safety devices Never fill the fuel tank while the engine is running turn the engine off and allow it to cool before A refuelling Never refuel near open flame or sparks while smoking and in poor ventilated areas Never overfill fuel tanks or fluid reservoirs In the event of a fuel spill do not attempt to start the engine until the fuel residue has been completely wiped up and the area surrounding the engine is dry When you are going to leave the machine after termination or interruption of the work secure the machine from unauthorized use or accidental movement P P TRANSPORTATION When loading and transporting the machine fasten the machine with its lifting eye properly O Make sure the crossbars on the safety catches are in good condition if so equipped Never trans
5. FRATASADORAS TIFON 600 900 1200 CON MOTOR ELECTRICO O DE GASOLINA TIFON 600 900 1200 POWER TROWELS WITH ELECTRIC MOTOR OR PETROL ENGINE TRUELLE TIFON 600 900 1200 AVEC MOTEUR ELECTRIQUE OU DE ESSENCE Manual de instrucciones User s manual Manuel d instructions MX TIFON 1008 INDICE 1 PR LOGO 2 CARACTER STICAS T CNICAS 2 1 FRATASADORAS CON MOTOR DE GASOLINA 2 2 FRATASADORAS CON MOTOR EL CTRICO 3 CONDICIONES DE UTILIZACI N PUESTA EN MARCHA FUNCIONAMIENTO Y MANTENIMIENTO DE LA M QUINA LOCALIZACI N DE AVER AS INSTRUCCIONES PARA PEDIR REPUESTOS ESQUEMA EL CTRICO TIFON 900E MONTAJE DEL ACELERADOR Y DEL SISTEMA DE SEGURIDAD HOMBRE MUERTO TIFON 900H Y TIFON 1200H Oo oO A FRATASADORAS TIFON 600 900 1200 CON MOTOR EL CTRICO O DE GASOLINA C A C OO N 12 12 13 14 1 PR LOGO Agradecemos la confianza depositada en la marca ENAR Para el m ximo aprovechamiento de su equipo recomendamos que lea y entienda las normas de seguridad mantenimiento y utilizaci n recogidas en este manual de instrucciones Las piezas defectuosas deben ser reemplazadas inmediatamente para evitar problemas mayores El grado de disponibilidad de la m quina aumentar si sigue las indicaciones de este manual Para cualquier comentario o sugerencia sobre nuestras m quinas estamos a su total disposici n FRATASADORAS TIFON 600 900 1200 CON MOTOR EL CTRICO O DE GASOLINA 2 CARACTER STICAS T C
6. IFON 900 and 107 2dB TIFON 1200 Proper protective equipment must be used Vibration caused by machinery is a risk for health The screed must always be handled using isolated gloves and all the necessary safety equipment Besides the user must rest each hour of effective work The hand arm vibration levels are 1 39m s TIFON 600 1 61m s TIFON 900 and 0 88m s TIFON 1200 FURTHERMORE THE OPERATOR IS COMPELLED TO RESPECT ADDITIONAL REGULATIONS ENFORCED TROWELS WITH ELECTRIC OR PETROL ENGINE 4 OPERATION AND MAINTENANCE STARTING PROCEDURE Electric models Insert the plug into its place Put the safety stop switch on ON position TIF N 600 E Just turn the switch to position 1 TIF N 900 E Turn the switch to position 1 If the machine does not start and just makes noise that shows you selected the wrong direction of rotation Stop the machine and turn the switch to position 1 on the opposite side To increase the rotation speed of the blades turn the switch to position 2 Petrol models Be sure the fuel tank is full Use the recommended gasoline to run the engine from its instruction book Check the engine oil levels Turn the engine stop switch to the position ON Open the fuel cock Set the speed control lever 1 3 of the way towards the high speed position If the engine is warm or the ambient temperature is high close the choke lever half way or keep it open fully If the engine
7. NICAS 2 1 FRATASADORAS CON MOTOR DE GASOLINA VELOCIDAD MOTOR POTENCIA DIMENSIONES M XIMA DE MOTOR FvrENGIA mm MAAIMA DE HONDA 65 kg GX160 5 5 1400 x 650 x 1000 HONDA 80 kg GX160 5 5 CV 2100 x 950 x 1040 600 H a STEERING ELADE ADJUSTMENT MECHANISM GASOLINE 1400 1000 STATIONARY RING e qu 5 BLADES 1390 2000 2000 950 FRATASADORAS TIFON 600 900 1200 CON MOTOR EL CTRICO O DE GASOLINA GAS SWITCH BLADE ADJUSTMENT MECHANISM STEERING ME al LIFTING SAFETY STOP SWITCH ENGINE CARRYING PIPE STATIONARY RING 2100 VELOCIDAD Modelo MOTOR DIMENSIONES mm MAXIMA DE GIRO rpm TIFON 600 E 65 kg 2 2 Kw TD 1400 x 650 x 1000 TIFON 900 E 80 kg 1 8 2 8 kW 2400 x 950 x 1040 GAS SWITCH SAFETY STOP SWITCH 600 E STEERING BLADE ADJUSTMENT MECHANISM GASOLINE 1400 STATIONAR
8. Y RING BLADES 900 E BLADE ADJUSTMENT MECHANISM STEERING LIFTING EYE SAFETY STOP WITCH ELECTRIC MOTOR 2000 CARRYING PIPE 2000 STATIONARY RING FRATASADORAS TIFON 600 900 1200 CON MOTOR EL CTRICO O DE GASOLINA 1 INTRODUCTION Thank you for trusting the ENAR brand For the maximum performance of the equipment we recommend to read carefully the safety recommendations maintenance and usage listed in this manual Defective parts should be replaced immediately to avoid major problems The effective longevity of the equipment will increase if the manual instructions are followed We will be glad to help you with any comments or suggestions in reference to our equipment TROWELS WITH ELECTRIC OR PETROL ENGINE 2 TECHNICAL SPECIFICATIONS 2 1 PETROL ENGINE MODELS WEIGTH PETROL ENGINE DIMENSIONS MAXIMUM POWER LxWxH mm TORQUE rpm TIFON 600 H 65 kg Ea 5 5HP 1400 x 650 x 1000 TIFON 900 H 80 kg 5 5 2100 950 1040 TIFON 1200 115 kg pens 2100 x 1250 x 1040 600 H a STEERING ELADE ADJUSTMENT MECHANISM
9. e It is located in the V belt plastic cover 3 Let us to know the right shipping instructions including the wished route the address and the consignee complete name 4 Do not return the parts without authorisation the return is done with freight prepaid 6 2 INSTRUCTIONS TO REQUEST WARRANTIES 1 The warranty is valid for 1 year after the purchasing of the machine the warranty will cover parts i with manufacturing defects In any case the warranty will cover a malfunction due to improper usage of the equipment The customer will always pay labour and shipping fees if the warranty is denied 2 In all warranty requests THE MACHINE MUST BE SENT TO ENARCO S A or to an AUTHORIZED DEALER always including the complete address and name of the consignee 3 The Technical Assistance Service will immediately notify to the customer if the warranty is accepted and if requested it will send a technical report 4 The warranty will be void if any equipment has been previously handled by personnel outside of ENARCO S A or not authorized by it NB ENARCO S A reserves the right to modify any part of this manual without prior notice TROWELS WITH ELECTRIC OR PETROL ENGINE 7 ELECTRIC SCHEME TIFON 900E Power trowel TIFON 900 E is served with the handle disassembled from the machine So the customer must assemble it to the machine and also connect the power cables to the motor The assembly of the handle is easy just place the ha
10. hine is in operation When transporting the trowel on a truck always keep blades fully horizontal flat on the floating disc MAINTENANCE TABLES Power trowels with petrol engine CLEAN THE MACHINE BYE PRESSURIZED WATER X CHECK THE BLADE PITCH ADJUSTMENT CHECK THE BLADE PITCH BOLTS AND CHECK OTHER BOLTS OF THE MACHINE IF NECESSARY TIGHTEN THEM CHECK ENGINE OIL LEVEL TROWELS WITH ELECTRIC OR PETROL ENGINE Power trowels with electric motor DAILY WEEKLY CLEAN THE MACHINE BY PRESSURIZED WATER X CHECK THE BLADE PITCH ADJUSTMENT X CHECK THE BLADE PITCH BOLTS AND CHECK OTHER BOLTS OF X THE MACHINE IF NECESSARY TIGHTEN THEM CHECK THE V BELT TIGHTNESS CHECK THE BLADES PUT OIL TO THE GREASE FITTINGS GEARBOX Check the gearbox oil level before every operation change the gearbox oil every year On the side of the gearbox there is a plug Use SHELL TIVELA COMPOUNDS A 400gr gear oil or equivalent MACHINE CLEANING Clean the machine after it has been used to prevent the collection of hardened cement Hard concrete cement paste is very difficult to remove To clean it use an old brush or hand brush CHANGE OF BLADES Be careful when replacing old blades Due to the way the blades wear the old blades become very sharp like a knife blade As a safety precaution use very heavy duty gloves during this operation to prevent the hands being cut Remove bolts and lock washers on each trowel arm and remove the blades Befo
11. is cold or the ambient temperature is low close the choke lever Pull the starter handle slowly until the resistance is felt Return the handle to its original position and pull swiftly Allow a longer warm up period in cold weather temperatures OPERATION Get into the operator s position behind the centre of the handle Attain a good feet position and start the machine A Push handle down to move the machine right B lift handle up to move the machine left gently C The machine will remain stationary it you do not apply any force up and or down n S CI OFF LA J LM Y Y M ET ON TROWELS WITH ELECTRIC OR PETROL ENGINE STOPPING THE MACHINE Electric motor Put direction switch on 0 position and get the plug out Do not leave the machine before getting the plug out Petrol engine Never use the choke to stop the engine Leave the machine run at an idle speed for 2 3 minutes to cool down Move the Gas lever to minimum throttle Turn the button which is on the gasoline engine to the OFF position to stop the machine lastly BLADE ADJUSTMENT The blade pitch control wheel is easy to reach for the operator To adjust the pitch just turn the wheel clockwise or anticlockwise depending on the desired pitch position During finishing setting up hardening may vary from area to area across the floor so the pitch adjustment can be changed to suit accordingly while the mac
12. ly Damaged cords increase the risk of electric shock Check the electrical cords for damage and worn Damaged cords can result to serious injuries Keep the motor switch and electrical cords dry Don t expose power tools to rain or wet conditions Never remove neutral grounding Don t do any modification on the plug Always check the power supply before running the trowel Using the wrong voltage supply will damage th motor Know the machine start up procedures Read the operator s manual For the proper use of this equipment please assure that the operator has been correctly informed of the content of this manual before using it SAFETY INSTRUCTIONS WHILE OPERATING THE MACHINE Stay alert watch what you are doing and use common sense when operating a power tool Do not use machines when you are tired or under the influence of drugs alcohol or medication Dress properly Hard hat heavy gloves eye protection ear protectors safety shoes dust mask or Q respirator are necessary Do not wear loose clothes or jewelry Loose clothes jewelry or long hair can be caught in moving parts O Keep properly fed and balanced at all times Check all adjustments of the machine Before start working check the machine functions work properly Q Check the cracked loosen missing parts of the machine and replace them by a new one if necessary Do not operate the trowel if the steering is free Keep your hair clothes and gloves away from
13. ndle base in the bolts placed in the side the gearbox Then put the washers and the nuts and tighten them firmly To connect the power cables to the motor these stops must be followed Remove the cover of the connections box Remove the gland seal of the connection box and the inner cap Insert the power cables into the connections box In this step is very important to avoid that the small plastic parts with numbers get lost These numbers will help to connect the cables Connect the cables following the scheme of the picture Finally put the connections box cover in its place TROWELS WITH ELECTRIC OR PETROL ENGINE 8 ASSEMBLY OF THE ACCELERATOR AND CONNECTION OF THE DEAD MAN SAFETY SYSTEM TIFON 900H AND TIFON 1200H Power trowels TIF N 900H and TIFON1200H are supplied with the accelerator and the dead man safety system disassembled so they must be assembled and connected before working To do this firstly it is necessary to connect the accelerator cable to the engine Remove the cover of the filter and then remove the filter Fix the accelerator cable cover with its clamp as shown in the picture below and put the accelerator cable into the prisoner of the engine Q REMOVE THE COVER OF THE FILTER SWITCH CABLE FROM THE HANDLE To check the dead man safety system works correctly start the engine with the lever of the safety system pulled Once the machine is working release the lever the
14. port or hoist the machine when the pans are attached to the trowel Never hoist the trowel over areas where people are standing or working On a carrier secure the machine safely to prevent its movement or its rolling over SERVICE Service must be performed only by qualified service technicians In order your trowel operates safely and properly for a long period of time periodic maintenance and occasional repairs are necessary Check the maintenance table to make the periodic maintenance Use genuine spare parts only The manufacturer does not bear any responsibility for damages arising from use of non original spare parts Do not remove while the trowel is hanging overhead Always support the trowel securely on a flat level surface before changing blades or pans Always use a safe nonflammable solvent when you clean parts Do not use flammable fluids or fluids that give off harmful vapors Do not make any service or maintenance without stopping the engine SPECIFIC SAFETY RULES Keep the rotating parts and stationary ring clean Pay extra care while operating the machine on wet working surfaces Wet surfaces may cause accidents Do not use the trowel for any purpose different than its intended purposes or applications Always store equipment properly when it is not being used Equipment should be stored in a clean dry location out of reach of children The acoustic power level of this machine can reach 107 2dB TIFON 600 106 8dB T
15. re installing new blades clean all concrete cement from bottom and side of the trowel be sure trowelling edge of the blade is behind the trowel arm Install bolts and lock washers on each trowel arm and fasten securely TIGHTEN THE V BELTS If you notice a loose on V belt check the tightness Especially in first using and V belt change Check the V belt tightness after 8 hours later Using your head finger push the V belt from its middle point lt must strech about 2cm If it strechs more it is loose For tightening loose the motor fixing screws tiil motor moves away on the table Loose the motor lock nut Loose the screws push the motor backward Checking the V belt tighteness do the same operations Until tighteness of V belt is desired value screw the motor luck nut and then screw the motor fixing screws TROWELS WITH ELECTRIC OR PETROL ENGINE V BELTS INSTALLATION AND MAINTENANCE WHILE INSTALLING THE V BELT Install the V belt by closing the centre of pulleys to each other and tighten While installing the V belt do not use a crowbar Adjust the pulley edges with respect to pulley shafts and V belt grooves to be on the same plane Fix the unbalanced pulleys V belts lengths should be the same in multi grooved pulleys Change all V belts at the same time in multi grooved pulleys to prevent worn out TROUBLES AND REASONS APPEARING IN V BELTS PROBLEMS CAUSES Ribbed belt breaking forcing the belt over pulle
16. y during use proper installation after a short period of installation techniques time ingress of foreign body fit and effective guard drive stalled check for lubrication Cuts and splits in the ambient temperature is too high Ensure good ventilating ribs abnormal belt slip contamination by chemical check drive tension protect the drive Severe belt vibration too low belt tension re tension the drive Excessive wear of ribs belt catching on protruding parts remove protrusions too low belt tension re tension the drive Excessive noise contamination by oil grease or protect the drive chemicals TROWELS WITH ELECTRIC OR PETROL ENGINE FACTORS AFFECTING THE V BELT LIFE AND POWER Couching the bottom Not fixed on to groove pulley surface of the pulley Overloading Unequal machined pulley grooves Stretching i Incorrect axial alignment Run out of pulley Dirt and dust Broken edge pulleys TROWELS WITH ELECTRIC OR PETROL ENGINE 5 LOCATING MALFUNCTIONS PROBLEM CAUSES SOLUTIONS The motor doesn t work Check the gas level Lo Check the gas admission key is open 6 INSTRUCTIONS TO ORDER SPARE PARTS 6 1 INSTRUCTIONS TO ORDER SPARE PARTS i 1 Every spare parts order must include PART CODE NUMBER AS STATED IN THE PARTS LIST We recommend including the MACHINE SERIAL NUMBER 2 The identification plate with serial and model number is located in the plate of the machin
Download Pdf Manuals
Related Search