Evolve™ Full Body Harnesses User Manual
Contents
1. User Instruction Manual Part Numbers RL 15502D RL 15503D RL 15502G S M RL 15502G L X RL 15503G S M RL 15503G L X RL 15502DB S M RL 15502DB L X RL 15502GB S M RL 15502GB L X R GID LIFELINES ISO 9001 2008 Registered Manual 103 0060 General Safety Information Under Penalty of Law This User Instruction Manual is not to be removed except by the user of this equipment m Current User Instruction Manuals must always be available to the user m Read and understand these instructions before using equipment Do not throw away these instructions Misuse or failure to follow warnings and instructions may result in serious personal injury or death Users must read and understand the User Instruction Manual provided with the product and be properly trained by their employer prior to use per OSHA 29 CFR 1910 66 and 1926 503 or applicable local standards Compliant fall protection and emergency rescue systems help prevent serious injury during fall arrest For instructions about proper use refer to supervisor User Instruction Manual or call Rigid Lifelines at 844 467 4443 Rigid Lifelines Evolve Full Body Harnesses Manual 2 844 467 4443 Purpose Rigid Lifelines Evolve Full Body Harnesses are designed to be used as part of a personal fall arrest controlled descent restraint rescue or work positioning system Fall Arrest System Components System Components Overview2. Attachment Points Donning Materials Accessories Training Inspection Cleaning Maintenance and Storage Labeling Inspection Log Service Policy One Year Equipment Warranty Rigid Lifelines Evolve Full Body Harnesses Manual 844 467 4443 co ao n om 6G Gc M 27 Back Cover Instructions For Use Failure to follow all instructions and limitations on the use of this equipment may result in serious personal injury or death Before using a personal fall arrest system employees shall be trained in accordance with the requirements of OSHA 29 CFR 1910 66 in the safe use of the system and its components Prior to each use inspect all personal fall arrest system equipment for wear damage and other deterioration Defective components must be removed from service immediately in accordance with the requirements of OSHA 29 CFR 1910 66 and 1926 502 After a fall or if any part of the oad indicator warning is showing the Evolve Full Body Harness must be removed from service and destroyed immediately Thoroughly evaluate and plan all elements of your fall protection system s before using your equipment Make sure that your system is appropriate for your needs and facility Also be sure to calculate fall clearance and swing fall clearance Users must have a rescue plan and the means to implement it This plan must provide prompt employee rescue or assure that employees have the ability to rescue themselves in
3. Body Harnesses Manual 844 467 4443 Rigid Lifelines Evolve Full Body Harnesses Manual 26 844 467 4443 Service Policy 1 Obtain as much information as possible concerning the problem through personal observation by yourself or other authorized personnel familiar with the job and equipment include model serial and or part numbers voltages speeds and any other special identifying features Be prepared to discuss the situation in detail All authorized labor charges will be based on straight time Hourly rates estimated man hours and not to exceed total dollar amount required for corrections are to be agreed upon before authorization is given There will be no allowances for overtime except in dire emergencies and then only with prior approval A verbal agreement may be reached immediately on both the method of correction and the approximate cost A warranty authorization number will be assigned for the specific incident A confirming written authorization will be torwarded to the distributor The distributor must send an itemized invoice showing our release number or invoice number and warranty authorization number after authorized corrections have been made A credit memo will be issued by accounting after the invoice has been received and approved Warranty charges ARE NOT to be deducted from outstanding open account invoices under any circumstances Any field corrections made prior to an authorization by Rigid Life
4. Employers are responsible for providing training to any employee who may be exposed to fall hazards Training will enable an employee to recognize and reduce fall hazards Training must be conducted by a Competent or Qualified Person Trainer and trainees must not be exposed to fall hazards during the training course Rigid Lifelines Evolve Full 1 9 Body Harnesses Manual 844 467 4443 Inspection Frequency Evolve Full Body Harnesses must be inspected prior to each use and annually by an OSHA defined Competent Person other than the user After a fall occurs or if any part of the load indicator warning located on webbing below dorsal D ring pad is showing the Evolve Full Body Harness must be removed from service If inspection reveals any defect inadequate maintenance or unsafe condition remove from service immediately Any harness with noticeable wear or damage must be removed from service immediately Contact Rigid Lifelines for help with replacement Any equipment that has been subjected to the forces of arresting a fall must be removed from service immediately Note Only manufacturer or entities authorized in writing by the manufacturer may make repairs to the product Otherwise equipment must not be altered in any way All components of the Evolve Full Body Harness must be inspected Inspect labels for presence and legibility Rigid Lifelines Evolve Full Body Harnesses Manual 20 844 467 44
5. Slip shoulder strap over one shoulder then pull the other shoulder strap around the back and over the second shoulder much like putting on a jacket The dorsal D ring will be located on your back while the chest strap is located in the front Straps must not be tangled as the harness hangs freely trom shoulders 3 Pull one leg strap between your legs and connect it to the opposite end on the same side Repeat with second leg strap Ensure that the leg straps are not twisted or crossed Leg straps must be comfortably snug to achieve proper adjustment Rigid Lifelines Evolve Full Body Harnesses Manual 1 4 844 467 4443 Failure to have the leg straps of the Evolve Full Body Harness properly adjusted during fall arrest may result in serious personal injury or death Rigid Lifelines Evolve Full 1 5 Body Harnesses Manual 844 467 4443 4 Fasten the chest strap just above the nipple line Chest strap should be snug with excess strap length secured through the web keepers 5 Adjust shoulder straps with the two adjusters located at the lower end of the shoulder strap Adjust the left and right sides to the same length The chest strap and front D ring if applicable must be centered on your lower chest Rigid Lifelines Evolve Full Body Harnesses Manual 1 6 844 467 4443 Adjustment of the shoulder straps may cause the dorsal D ring to move and may need to be repositioned up or down as need
6. anchored at foot level and measured from the anchorage point of lanyard to the nearest obstruction below The total fall clearance combines the sum of the length of the lanyard free fall distance the maximum elongation of the lanyard 5 feet or 1 5 meters the average distance between the worker s dorsal D ring 5 feet or 1 5 meters and the safety factor 3 feet or 0 9 meters Image 2 Shock Absorbing Lanyard SAL U From Connection Point of Lanvard to Anchorage Point Before Fall Length of Lanyard 6 feet Deceleration Distance 48 inches or 60 inches Required Fall Clearance Average Height to Worker s Dorsal D Ring 5 feet Safety Factor 3 feet Rigid Lifelines Evolve Full Body Harnesses Manual 1 0 844 467 4443 Swing Fall To minimize the possibility of a swing fall work as directly under the anchorage connector as possible Striking objects horizontally due to the pendulum effect may cause serious injury Swing falls also increase the vertical fall distance of a worker compared to a fall directly below the anchorage connector Swing falls may be reduced by using overhead anchorage connectors that move with the worker Workers accessing areas greater than 30 off plumb from overhead anchorage are at a higher risk for severe injury Striking objects horizontally due to the pendulum effect of a swing fall may cause serious injury or death Swing Fall WARNING Workers accessing areas greater than 3
7. with ANSI 2359 13 and 6 ft Free Fall are designed for up to 6 tt free fall applications with a maximum capacity up to 310 Ib 141 kg including clothing tools etc Evolve Full Body Harnesses shall be used as part of a personal fall arrest system that limits the maximum Tree fall distance to 6 ft 1 8 m If used with appropriate connecting system Evolve Full Body Harnesses may be used with tree falls exceeding 6 ft 1 8 m Full Body Harnesses shall only be used as part of a controlled descent or rescue system that eliminates free fall unless attached to the dorsal D ring When attached to the dorsal D ring the maximum free fall distance is 6 ft 1 8 m Full Body Harnesses shall only be used as part of a work positioning system that limits the maximum Tree fall distance to 2 ft 0 6 m Only use components rated for the same weight capacity Not all fall protection components are rated for the same user weight capacity Proper precautions should always be taken to remove any obstructions debris material or other recognized hazards from the work area that could cause injuries or interfere with the effective operation of the system Do not use fall protection equipment for towing or hoisting Protect all synthetic material from slag hot sparks open flames or other heat SOUICES Rigid Lifelines Evolve Full Body Harnesses Manual 6 844 467 4443 Do not expose equipment to environmental hazards an
8. 0 off plumb from overhead anchorage are at a higher risk for severe injury Rigid Lifelines Evolve Full 1 1 Body Harnesses Manual 844 467 4443 Attachment Points The dorsal back D ring affixed to all Rigid Litelines Evolve Full Body Harnesses is for fall arrest or restraint systems The dorsal D ring may also be used for rescue applications Hip D rings are used for positioning and restraint systems Always use both hip D ring connections when securing work positioning devices Hip D rings are not for fall arrest or climbing applications e Rigid Lifelines Evolve Full Body Harnesses Manual 1 2 844 467 4443 Donning Not all fall protection components are rated for the same user weight capacity Only use components rated for the same weight capacity There must be a functional rescue plan if users of fall protection systems cannot rescue themselves Note Sewn terminations should be secure complete and not visibly damaged No load indicators shall be deployed Damaged and other deteriorated and defective components must be immediately removed from service in accordance with the requirements of OSHA 29 CFR 1910 66 and 1926 502 Fitting an Evolve Full Body Harness 1 Hold the dorsal back D ring of the harness and shake to allow all straps to fall into place Straps must not be buckled or twisted Rigid Lifelines Evolve Full 1 3 Body Harnesses Manual 844 467 4443 2
9. 43 To Inspect Webbing Bend a portion of the webbing 6 8 in 15 20 cm into an upside down U shape Continue along all webbing inspecting for tears cuts fraying abrasion discoloration burns holes mold pulled or broken stitches or other signs of wear and damage Adjust all keepers buckles padding and D ring to inspect webbing hidden by these components Sewn terminations must be secure complete and not visibly damaged Check all buckles for damage distortion cracks breaks and rough or sharp edges Inspect for any unusual wear frayed or cut fibers or broken stitching of the buckle attachments Make sure buckles properly engage Tongue buckle grommet tongues should be free of distortion in shape and motion They should overlap the buckle frame and move freely back and forth in their socket The roller should turn freely on frame Inspect for loose distorted or broken grommets Webbing should not have additional punched holes Rigid Lifelines Evolve Full 21 Bodv Harnesses Manual 844 467 4443 The outer bars and center bars on friction and slotted mating buckles must be Straight Ensure that the Quick Connect buckle s dual tab release mechanism is free of debris and engages properly Double check the buckle locking mechanism by tugging on both halves of the buckle to make sure It is firmly connected and will not disengage All markings must be legible and attached to the product All hardw
10. A complete fall arrest system consists of the following components Anchorage Body Support and Connecting Devices Note For continuous protection more than one system may be needed Anchorage OSHA 29 CFR 1926 502 states that an anchorage Shall be independent of any anchorage being used to support or suspend plattorms and capable of supporting at least 5 000 pounds 22 2 kilonewtons per employee attached or shall be designed installed and used as follows as part of a complete personal fall arrest system which maintains a safety factor of at least two and under the supervision of a qualified person Body Support A body support is the component of a personal fall arrest system that is worn on or around the body Per OSHA 29 CFR 1926 502 effective January 1 1998 body belts are not acceptable as part of a personal fall arrest system Full body harnesses must be used for all fall arrest systems Note The use of a body belt is acceptable in a positioning device system Connecting Devices A connecting device is the link between the body support and anchorage Connecting devices will vary depending on the application Rigid Lifelines Evolve Full 3 Body Harnesses Manual 844 467 4443 Table of Contents General Safety Information Purpose Fall Arrest Components Instructions For Use Limitations For Use Anchorage Requirements Connection Compatibility Limitations Fall Clearance Clear Fall Charts Swing Fall
11. Manual 844 467 4443 Limitations For Use This equipment is designed to be used in temperatures ranging from 40 F to 130 F 40 C to 54 C Do not expose this equipment to chemicals or harsh solutions that may have a harmful effect Contact Rigid Lifelines with any questions Use caution when working with this product near moving machinery electrical hazards sharp edges or abrasive surfaces as contact may cause equipment failure personal injury or death Minors pregnant women and anyone with a history of back and or neck problems should not use this equipment Do not use or install equipment without proper training from a Competent Person as defined by OSHA 29 CFR 1926 32 f Only Rigid Lifelines or entities authorized in writing by Rigid Lifelines shall make repairs or alterations to the equipment Evolve Full Body Harnesses are designed for users with a maximum capacity up to 310 141 kg including clothing tools etc If the system is used by an employee having a combined tool and body weight between 310 Ib 140 6 kg and 400 Ib 181 4 kg then the employer must appropriately modify the criteria and protocols to provide proper protection for such heavier weights or the system will not be deemed to be in compliance with the requirements of OSHA 1926 502 d 16 ANSI capacity range is 130 Ib 310 Ib 59 kg 140 6 kg Personal Energy Absorbers and Energy Absorbing Lanyards marked
12. are must be free of cracks sharp edges deformation corrosion or any evidence of defect Cleaning Maintenance and Storage Wear proper Personal Protective Equipment when performing Inspection Cleaning and Maintenance procedures Safety glasses and gloves are recommended Cleaning Rigid Lifelines Evolve Full Body Harnesses can be wiped down with a mild detergent and rinsed with a clean cloth to remove detergent The hardware can also be wiped down with a clean dry cloth to remove grease or dirt Maintenance Any Rigid Lifelines Evolve Full Body Harness requiring maintenance must be tagged unusable and removed from service Only Rigid Lifelines or persons or entities authorized in writing by Rigid Lifelines shall make repairs or alterations to the equipment Cleaning and maintenance may be performed by the user Rigid Lifelines Evolve Full Body Harnesses Manual 2 2 844 467 4443 Storage When not in use Rigid Lifelines Evolve Full Body Harnesses should be stored in a cool dry place out of direct sunlight Do not store in areas where damage from environmental factors such as heat light excessive moisture oil chemicals and their vapors or other degrading elements may be present Do not store damaged equipment or equipment in need of maintenance in the Same area as product approved for use Equipment must be cleaned and dried prior to storage Equipment that has been stored
13. d chemicals which may produce a harmful effect Polyester should be used in certain chemical or acidic environments Do not allow equipment to come in contact with anything that will damage it including but not limited to sharp edges abrasive surfaces moving machinery or high temperature applications like welding heat sources and electrical areas Evaluate space below work area to ensure potential fall path is clear of obstructions Allow adequate fall clearance below the work surface Consult chart on page 9 Anchorage Requirements All anchorages to which the Personal Energy Absorbers and Energy Absorbing Lanyards attach must meet the requirements of OSHA 29 CFR 1910 66 and ANSI 2359 1 2007 OSHA states Anchorages to which personal fall arrest equipment is attached shall be capable of supporting at least 5 000 Ib 22 2 kN per employee attached or shall be designed installed and used as part of a complete personal fall arrest system which maintains a safety factor of at least two under the supervision of a qualified person ANSI Z359 1 2007 states that anchorages in a personal fall arrest system must have strength capable of sustaining static loads applied in all directions permitted by the system of at least a Two times the maximum arrest force permitted on the system with certification or 5 000 Ib 22 2 kN in the absence of certification When more than one personal fall arrest system is attached t
14. ed to achieve correct position 6 After all straps have been tightened and harness fits snugly secure all excess Straps through the web keepers Materials Webbing All Rigid Lifelines9 Evolve Full Body Harnesses are constructed with 1 75 in 44 mm polyester webbing Hardware All hardware on the Evolve Full Body Harness meets the ANSI Z359 1 2007 standard and OSHA 29 CFR 1910 66 and 1926 502 requirements Rigid Lifelines Evolve Full 1 7 Body Harnesses Manual 844 467 4443 Accessories Rigid Lifelines Suspension Trauma Relief Pack The Rigid Lifelines Suspension Trauma Relief Pack RL TRP is available for use on all Rigid Lifelines Evolve Full Body Harnesses The Suspension Trauma Relief Pack must be choked onto the vertical torso straps of the harness located above the primary connection opening of the hip joint Refer to the Suspension Trauma Relief Pack User Instructions for more intormation Lanyard Storage Keepers Approved lanyard storage keepers are located on all Rigid Lifelines Evolve Full Body Harnesses where the shoulder strap meets the chest strap Lanyard storage keepers are only approved for the connection of the unused lanyard length to the harness Rigid Lifelines Evolve Full Body Harnesses Manual 1 8 844 467 4443 Never attach the unused length of the lanyard back to the Evolve Full Body Harness at any location other than an approved lanyard storage keeper Training
15. ents materials and anchorage to match the system application the work work place hazards and the environment Connectors used on this harness must be compatible dimensionally to prevent accidental roll out or accidental disconnection Do not expose to acid acid fumes chemicals corrosives UV rays solar exposure or environments or temperatures above 190 degrees F that could weaken the parts of this harness Do not misuse harness abuse alter or attempt repairs to 4 this product Product complies with ANSI 2359 1 and OSHA standards A rescue plan must be in place and user must be properly trained R GID before using this product LIIFELINES RIGID LIFELINES Morgantown PA 19543 e 800 869 2080 or 610 286 7200 rigidlifelines com Evolve M Fall Indicator FALL INDICATOR Do not re use any unit that has arrested a fall or has this fall indicator deploved Remove from service immediatelv Rigid Lifelines Evolve Full 23 Body Harnesses Manual 844 467 4443 Evolve Long Label WARNING WARNING REMOVE FROM SERVICE Read all instructions EVO V 3 if subject to a fall arrest or before use Do not remove if unit fails inspection product labels Remove WARNING Follow the manufacturer s instructions included with the equipment at the time of shipment before using Improper use of this equipment could result in serious injury or death Date of MFG Model Size Universal Material Pol
16. for an extended period must be inspected as described in these User Instructions prior to use Labeling All labeling must be legible and attached to the full body harness Evolve logo Evolva Evolve Warning Label A This entire label must be read and understood before using this harness The entire user s manual for this harness must also be read and understood before using this harness lf you do not have the user s manual for this harness contact RIGID LIFELINES for a free copy WARNINGS THIS HARNESS MUST BE INSPECTED PRIOR TO EACH USE Inspect for rips tears fraying excessive wear dry rot deterioration UV rays or solar exposure paint chemical salt water acid acid fume contamination or any possible reason that would compromise the harness during a fall Failure to do so may result in serious injury or death Always use common sense Harness must be removed from service immediately if there is any suspicion that the harness could be compromised during a fall if there is a fall or if the unit fails inspection Maximum capacity including man tools clothes and equipment is 310 LBS The inspection log must be maintained by a fall protection competent person at least every six months The maximum arresting force force of the fall shall be no greater than 900 LBS Avoid contact of harness with sharp or abrasive edges Do not remove this or any labels This harness is part of a system A qualified person must select the compon
17. lines will not be accepted as a warranty charge or the responsibility of Rigid Lifelines Any modification to the equipment made without prior approval of the seller will void all warranties A verbal authorization for modification may be obtained in which event a warranty authorization number will be assigned for the specific modification A confirming written authorization will be forwarded to the distributor Rigid Lifelines Evolve Full 27 Body Harnesses Manual 844 467 4443 One Year Equipment Warranty Rigid Lifelines warrants all Rigid Lifelines fall protection soft goods devices connectors and accessories to be free from defects in material and workmanship for a period of one 1 year commencing on the date of shipment to the first retail purchaser Purchaser Rigid Lifelines is dedicated to offering superior service and quality products to all of our customers If you would like to contact a customer service representative please call the following number 1 844 467 4443 We will be happy to assist you in any way that we can These warranties do not extend to equipment which has been subject to misuse use in excess of rated capacity negligent operation use beyond Rigid Lifelines published service factors improper installation or maintenance adverse environments and does not apply to any equipment which has been repaired or altered without Rigid Lifelines written authorization This warranty is void for any p
18. nect to the equipment in question The following conditions can result in rollout when a non locking snap hook is used Avoid the following connections Direct connection of a snap hook to horizontal lifeline Two or more snap hooks connected to one D ring Two snap hooks connected to each other A snap hook connected back on its integral lanyard A snap hook connected to a webbing loop or webbing lanyard Improper dimensions of the D ring rebar or other connection point in relation to the snap hook dimensions that would allow the snap hook keeper to be depressed by a turning motion of the snap hook Rollout A process by which a snap hook or carabiner unintentionally disengages trom another connector or object to which it is coupled ANSI Z359 0 2007 Rigid Lifelines Evolve Full Body Harnesses Manual 8 844 467 4443 Fall Clearance Clear Fall Charts Clearance Requirements These illustrations are an example of how to calculate fall clearance when using a self retracting lanyard or a shock absorbing lanyard Image 1 shows a self retracting lanyard anchored overhead with the other end connected to the dorsal D ring of a full body harness When positioning a self retracting lanyard include the following distances in your calculations Using the Rigid Lifelines Defy Selt Retracting Lanyard will require a total fall clearance of approximately 7 5 feet 2 3 meters as measured from the working level to the nea
19. o the anchorage the strength in a and must be multiplied by the number of personal fall arrest systems attached to the anchorage Anchorages used in controlled descent and rescue systems must be capable of supporting loads of 3 100 ft lb 13 8 kN for non certified anchorages or a 5 1 safety factor for certified anchorages per ANSI Z359 4 2007 Anchorages used in restraint systems must be capable of supporting loads of 1 000 ft Ib 4 5 kN for non certified anchorages or two times the foreseeable force for certified anchorages per ANSI Z359 2 2007 Anchorages used in work positioning systems must be capable of supporting loads of 3 000 ft lb 13 3 KN for non certified anchorages or two times the foreseeable force for certified anchorages per ANSI Z359 2 2007 Anchorages should be located as vertically as possible above the user s head and be positioned as not to exceed the maximum allowable free fall for the system Rigid Lifelines Evolve Full 7 Body Harnesses Manual 844 467 4443 Connection Compatibility Limitations All Rigid Liftelines equipment must be coupled to compatible connectors OSHA 29 CFR 1926 502 prohibits snap hooks from being engaged to certain objects unless two requirements are met 1 It must be a locking type snap hook 2 It must be designed for making such a connection a Designed tor means that the manufacturer of the snap hook specifically created the snap hook to be used to con
20. rest obstruction below The total fall clearance combines the sum of the maximum allowable fall arrest distance of 54 inches or 4 5 feet 1 4 meters and the safety factor of 3 feet 0 9 meters Image 1 Self Retracting Lanyard SRL Before Fall From Walking Working Surface Maximum Arrest Distance 54 inches Required Fall Clearance Safety Factor 3 feet Rigid Lifelines Evolve Full 9 Body Harnesses Manual 844 467 4443 Image 2 shows a shock absorbing lanyard anchored overhead with the other end connected to the dorsal D ring of a full body harness Note that the length of your shock absorbing lanyard in relation to where it is attached is directly related to the amount of fall clearance that you will need When using a shock absorbing lanyard include the following distances in your calculations Using the 6 Foot Rigid Lifelines Connex Shock Absorbing Lanyard will require a total fall clearance of approximately 18 feet 5 5 meters as measured from the anchorage point of lanyard to the nearest obstruction below The total fall clearance combines the sum of the length of the lanyard the maximum elongation of the lanyard 4 feet or 1 2 meters the average distance between the worker s dorsal D ring 5 feet or 1 5 meters and the safety factor 3 feet or 0 9 meters Using an extended free fall 12 foot Connex Shock Absorbing Lanyard will require a total fall clearance of approximately 20 feet 6 1 meters when
21. roduct that is designed to deform or absorb energy during a fall event and needs to be replaced after a fall event has occurred Written notice of any claimed defect must be given to Rigid Lifelines within thirty 30 days after such defect is discovered Rigid Lifelines obligation and Purchaser s sole remedy under this warranty is limited to at Rigid Lifelines discretion the replacement or repair of the equipment at Rigid Lifelines factory or at a location approved by Rigid Lifelines THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES WHATSOEVER WHETHER EXPRESS IMPLIED OR STATUTORY SELLER MAKES NO WARRANTY AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE EQUIPMENT AND MAKES NO OTHER WARRANTY EITHER EXPRESS OR IMPLIED Rigid Lifelines shall not be liable under any circumstances for any indirect special or consequential damages including but not limited to lost profits increased operating costs or loss of production This warranty shall not extend to damages including but not limited to lost profits increased operating costs or loss of production This warranty shall not extend to any components or accessories not manufactured by Rigid Lifelines example casters with the exception of the components systems or accessories involved with XSPlatforms and purchaser s remedy for such components and accessories shall be determined by the terms and conditions of any warranty provided by the manufacturer of
22. such components and accessories Rigid Lifelines 730 Hemlock Road Suite 104 aa Morgantown PA 19543 GID Toll Free 844 467 4443 a RoS Local 610 286 8030 FELINES 610 286 6108 RigidLifelines com info rigidlifelines com 2014 All rights reserved Specifications subject to change without prior notice RLL EFBHO114V1
23. the event of a fall Store this equipment in a cool dry and clean environment that is out of direct sunlight when not in use After a fall occurs this equipment must be removed from service and destroyed immediately Failure to follow all instructions and limitations on the use of Personal Energy Absorbers and Energy Absorbing Lanyards may result in serious personal injury or death Failure to have the leg straps of the Evolve Full Body Harness properly adjusted in the event of a fall arrest may result in serious personal injury or death Never attach the unused leg of the lanyard back to the Evolve Full Body Harness anywhere other than an approved lanyard storage keeper To minimize the potential for accidental disengagement a Competent Person must ensure system compatibility All equipment must be inspected before each use according to the instructions found in this User Instruction Manual All equipment should be inspected by a qualified person on a regular basis Never use fall protection equipment for purposes other than those for which it was designed Environmental hazards should be considered when selecting fall protection equipment Do not expose the equipment to any hazard which it is not designed to withstand Consult Rigid Lifelines in cases of doubt Never remove product labels because they include important warnings and information for the Authorized Person User Rigid Lifelines Evolve Full 5 Body Harnesses
24. yester Serial DO NOT REMOVE THIS LABEL Rigid Lifelines Evolve Full Body Harnesses Manual 844 467 4443 ASN HIVI 100438 193dSNI LSNW YISN 1511 JO 3460 168 G SI JINPOJA JO 991AJ9S DO NOT REMOVE THIS LABEL 24 from service if subject to fall Avoid sharp edges and abrasive surfaces Inspect before each use Use only compatible connections Dorsal D Ring for fall arrest attachment If present side D Rings for positioning only A Shoulder Strap B Chest Strap C Front Adjustment Strap D Back D Ring E Lanyard Keeper Inspection Log Notes If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE User must inspect prior to EACH use Competent Person other than user must complete formal inspection at least every 6 months Competent Person to inspect and initial Date of first use Product lifetime is 5 years as long as it passes pre use and Competent Person inspections REMOVE FROM SERVICE 5 years after date of first use or if not recorded from date of manufacture This inspection log must be specific to one Internal Shock Lanyard Separate inspection logs must be used for each Internal Shock Lanyard All inspection records must be made visible and available to all users at all times Sample 5 Year Inspection Grid pyr i 2 5 5 po Rigid Lifelines Evolve Full 2 5
Download Pdf Manuals
Related Search