Home

AX2065A

1. USER MANUAL AX2065A active vertical array loudspeaker KEY FEATURES e High output line array element e Transmission Line back loading for clean mid bass reproduction e Compact size very good output to weight ratio e Natural sound Transmission Line HF projection wave forming device e High quality low compression low distortion HF driver e 96KHz 40 bit floating point CORE processing with PRONET remote control e Very stable horizontal coverage e Digitally controlled Class D amplifier module with SMPS INTRODUCTION The AX2065A Vertical Line Array element is designed for a wide range of sound reinforcement applications where a flexible and easy to use vertical array systems is needed The AX2065A has been designed both for rental live sound applications and for fixed installations and has been engineered for the simplest use possible but without sacrificing anything in sound quality and performance very natural sound A transmission line wave forming waveguide has been used to load the HF driver in order to provide a detailed and natural sound and to achieve a long distance HF projecting amp Capacity The two 6 5 woofers are back loaded by a short hybrid transmission line that minimizes the effect of the box resonances and eliminates the boxy mid bass sound commonly obtained from regular bassreflex enclosures The AX2065A is processed by 40bit 96kHz floating point CORE DSP and powered by DA SERIES digital power modules a n
2. 93 Input Impedance 20 kQ balanced Taper angle 5 Input Sensitivity 4 dBu 1 25 V Construction 15 mm reinforced Phenolic Birch l CORE processing 96kHz 40bit floating Paint High resistance water based paint Signal Processing point SHARC DSP 24 bit AD DA converters Suspension system 4 Presets Standard Long Throw Down Fill Front Suspension Aluminium Fast Link structure with Fast Pin Direct access Controls Single Box User Back Suspension High Strength Steel with Fast Pin Network Termination GND Link Net Weight 22 5 Kg 49 6 lbs Nominal consumption is measured with pink noise with a crest factor of 12 dB this can be considered a standard music program AXIOM MECHANICAL DRAWING ob OPTIONAL ACCESSORIES AXCASE05 AXCASE06 NAC3FCA NAC3FCB NE8MCB NC3MXXBAG NC3FXXBAG SW215A SW215AF Carrying Case for 4 box unit Flying Bar AX2065P Carrying Case for 4 box unit USB2CAN Neutrik Powercon BLUE PLUG KPTSW215 Neutrik Powercon WHITE PLUG KPTAX2065 Neutrik Ethercon PLUG BOARDAC2P Neutrik XLR M KPAX265 Neutrik XLR F KP010 Active Subwoofer DHSS10M20 Flyable Active Subwoofer see www proel com for detailed description and other available accessories SPARE PARTS NAC3MPA NAC3MPB 94SP12265 PLG716 91AMD2065 AX2065 used as conventional system Passive vertical array loudspeaker PRONET network converter Fly bar for Axiom AX2065 and SW215 Loudspeakers Fly bar for Axiom AX2065 o
3. network transmission of remote control data over long distance or multiple unit applications TERMINATE In a PRONET network the last loudspeaker device must be terminated with an inner load resistance especially AX2065P ONLY in a long run cabling press this switch if you want to terminate the unit POWER OUT AX2065A is able to power an additional passive AX2065P module through the available power output on the back panel POWER OUT x A N WARNING connect a single AX2065P module only MIN LOAD 8 0 AIMING and SUSPENDING INSTRUCTIONS PREDICTION EASE Focus 2 To aim correctly a complete system we suggests to use always the Aiming Software EASE Focus 2 The EASE Focus 2 Aiming Software is a 3D Acoustic Modelling Software that serves for the configuration and modelling of Line Arrays and conventional speakers close to reality It only considers the direct field created by the complex addition of the sound contributions of the individual loudspeakers or array components The design of EASE Focus is targeted at the end user It allows the easy and quick prediction of the array performance in a given venue The scientific base of EASE Focus stems from EASE the professional electro and room acoustic simulation software developed by AFMG Technologies GmbH It is based on the EASE GLL loudspeaker data file required for its use AXIOM_AX Series_v2_0 GLL please note that the version must be 2 0 or more The GLL file contains the da
4. 7 0 76 TE a lz og O frr Note that the ideal aiming angle often doesn t correspond to the pinpoint there is often a little difference between ideal aiming and real aiming and its value is the Delta angle positive delta angle can be adjusted a little using two ropes negative delta angle are self adjusted a little because the cables weighs on the back of the array With some experience it s possible to consider preventively these required little adjustments During the flown set up you can connect the elements of the array to their cables We suggest to discharge the weight of the cables from the flying pinpoint by tying them with a textile fibre rope instead of letting them hang freely in this way the position of the array will be much more similar to the simulation produced by the software CENTRE OF GRAVITY Pin locking and splay angles set up LOUDSPEAKER SPLAY ANGLES SET UP The figure below shows how to insert correctly the locking pin and how to set up the splay angle between loudspeakers HINGE BAR OF PREVIOUS BOX LOCK THE PIN IN THE HOLE TO OBTAIN THE 95AXM014 LOCKING PIN REQUIRED SPLAY ANGLE aN 0 1 c e lt 3 press and 4 insert 5 4 DROP LINK tee 6 BLOCK CAM 70 HOLE m gt CA 8 release and oeni l lock HOLE 10 0 10 gt USE THIS HOLE TO LOCK THE HINGE BAR WHEN THE Wind loads LOUDSPEAKER IS REST When planning an open air event it is essential to obtain current weather and wind inf
5. Fly bar serving as ground support are allowed to be set up as ground max splay angle 10 stack In the stack configuration you have to use the three optional max splay angle 10 BOARDAC2P feet and the fly bar must be mounted upside down on the ground Coupling system in the front do not require any adjustment using two locking pins each loudspeaker box is fixed to the previous The slotted bar in the back is inserted in a U shaped frame which features a series of numbered holes Sliding the slotted bar in the U shaped frame of the next loudspeaker and inserting a locking pin in one of the numbered holes it is possible to adjust the relative splay angle between two adjacent loudspeakers in the array column The optimal splay angles can be simulated using the EASE Focus 2 software max splay angle 10 y T max splay angle 10 POWER AMPLIFIERS The AX2065A is powered by DA SERIES digital power modules a new generation of CLASS D power amplifier with digitally controlled SMPS The innovative technology used for these amplifiers including also the use of a variable switching frequency offers performances at the top of the range such as a superior sound definition at any audio frequency very high dynamics also for low level signals and very low distortion even at the maximum power The superior sound quality can be compared with top of the range AB class analog systems while the DA modules feature a higher dynamics very comp
6. OUT Powercon NAC3FCB power output connector grey This is connected in parallel with the MAINS IN The maximum load applicable depends on the mains voltage With 230V we suggest to link a maximum of 4 AX2065A loudspeakers with 120V we suggest to link a maximum of 2 AX2065A loudspeaker INPUT Audio signal input with locking XLR connector It has a fully electronically balanced circuitry including AD conversion for the best S N ratio and input headroom LINK A direct connection from the input connector to link other speakers with same audio signal ON This LED indicates power on status PROT This red LED lights when the amplifier module is in protect mode for an internal me 7 fault and consequently the amplifier is muted W SIGN LIMIT This LED lights in green to indicate the presence of the signal and lights in red when an internal limiter reduces the input level GND LIFT This switch lift the ground of the balanced on audio inputs from the earth ground of the amplifier module PROT PRESET BUTTON This button has two function 1 Pressing it while powering on the unit ID ASSIGN the internal DSP assigns a new ID to the unit for the PRONET remote control operation Each loudspeaker must have a unique ID to be visible in the PRONET network When you assign a new TERMINATE ID all the other loudspeakers with the ID already assigned must be ON and connected to the network 2 Pressing it with
7. act size and light weight and efficiency above 90 The DA module employed for powering the AX2065A deliver in an ultra compact package a maximum power of 2000W 1000W are delivered to the internal speakers the other 1000W are delivered to the AX2065P connected in parallel using the POWER OUT speakon connector Soo cd00CO 000008 SIGNAL PROCESSING The system processing is based on the CORE DSP platform which has been designed by the PROEL R amp D Laboratories using one of the most advanced SHARC DSP for audio application It features 40bit 96kHz floating point resolution and high quality 24bit AD DA converters for a perfect signal integrity a dynamic range in excess of 110dB and a superior sonic performance Thanks to its massive processing power the CORE platform is capable of providing the most sophisticated algorithms for speaker processing together with remote control and networking capability The PRONET control software working on a solid and reliable CANBUS based network protocol provides an intuitive interface for the remote control of the whole system with the possibility of eqing delaying increasing the protections and monitoring the status of the amplifier PRONET Network PRONET software has been developed in collaboration with sound engineers and sound designers in order to offer an easy to use tool to setup and manage your audio system With PRONET you can visualize signal levels monitor internal status and
8. an the other or with a earth connection Make sure that power supply mains line has a proper earth connection Power supply cord should be unplugged from the outlet during strong thunderstorm or when left unused for a long period of time CE CONFORMITY Proel products comply with directive 2004 108 EC EMC as stated in EN 55103 1 and EN 55103 2 standards and with directive 2006 95 CE LVD as stated in EN 60065 standard PROEL S p A World Headquarter Via alla Ruenia 37 43 64027 Sant Omero Te ITALY Tel 39 0861 81241 Fax 39 0861 887862 www proel com AXIOM
9. by the aiming software When lifting the system always proceed gradually step by step paying attention to secure the fly bar to the box and the box to the other boxes before pulling up the system this makes easier to insert properly the locking KPTSW215 FLY BAR AND ACCESSORIES M10 FOOT FOR STRAIGHT SHACKLE 16mm STACKED INSTALLATION i OPTIONAL 16mm IDENTIFICATION AND cos Pad N FRONT BOX PIN ATTACHMENT pins Also when the system is released down unlock gradually the pins During the lifting be very careful to not let the cables enter the space between one enclosure and the other as their compression could cut them SUSPEND HOLE INDICATOR SUSPEND HOLES FRONT BOX 7 PIN ATTACHMENT REAR BOX PIN ATTACHMENT AXIOM Fly bar suspension and angle setup centre of gravity The first figure shows where the normal centre of gravity is with one box or several boxes arranged in a line Usually the boxes are arranged to make an arc for the best coverage of the audience so the center of gravity moves backward The aiming software suggests the ideal suspension pinpoint taking into account this behaviour fix the straight shackle in this position KPTSW215 FLY BAR FOR FLOWN ARRAY __ _ _ _KPTSW215 FLOWN PINPOINT SINGLE PINPOINT FOR STRAIGHT SHACKLE Position amp Orientation X m 0 00 Ver 7 Y m Z m Rigging Box Count Weight E Pinpoint 5 Delta
10. d to verify the vertical array angle It can be used at the top or at the bottom of the array In this case you have to sum all splay angles so the maximum precision is needed for aiming the vertical array particularly for long throw applications LASER DISTANCE METER This instrument can be useful to measure the height of the vertical array and to know the distance between FOH Subs and FOH Array for setting the delay time SMAART or similar acoustic measurement system Madd V7 These are useful to measure delays phase and response of the system EXAMPLE OF INSTALLATION IN A THEATRE WITH BALCONY Here below you can see an example of the use of different PRESETS in an AX2065 flown array installed in a big theatre with balcony The TOP BOXES of the array are aiming at the balcony while the DOWN FILL box is aiming at the audience close to the stage I 25 00 25 50 75 100 125 60 175 200 225 20 2S FARE Oyarwe 921 3S0 325 OP BOXES the power level at the end of the balcony is lower as well as the high frequency level TOP BOX DOWN FILL BOXES the power level in the proximity of the stage is higher as well as the high frequency level AX2065A PRESET RESPONSE LONG THROW SINGLE DOWNFILL STANDARD In order to optimize the array performances for this specific application the PRESETS should be used in the following way Load the STANDARD preset in the central box
11. edit all the parameters of each connected device You can download the PRONET software from the PROEL website at http www proel com click on the link in the AX2065A product page The AXIOM active loudspeaker devices can be connected in a network and controlled by the PRONET software For the network connection the PROEL USB2CAN converter optional accessory is needed The first time you connect a device with the USB2CAN converter Windows O S will ask you to install the driver files which you can find in the Driver folder within the Pronet application folder by default is C Program Files Proel Pronet Driver or if you changed it lt your path gt Driver Please refer also to Installation and Drivers paragraphs in the Pronet documentation The PRONET NETWORK is based on a robust reliable and fast communication protocol called CANBUS The devices in a PRONET NETWORK are connected together with a linear bus topology The USB2CAN converter must be connected to the network input of the first device the network output of the first device is connected to the input of the second and so on For the network connections simple RJ45 cat 5 or cat 6 ethernet cables can be used please don t confuse a ethernet network with a PRONET network these are completely different and must be fully separated also both use the same kind of cable The beginning and the end of a PRONET NETWORK must be terminated One side is terminated by the USB2CAN conve
12. es Load the LONG THROW preset in the TOP 1 or 2 boxes in order to compensate the loss of power level and high frequencies of the program sent the upper deck of the theatre Load the DOWN FILL SINGLE BOX preset in the BOTTOM box in order to smooth the high frequency content of the program sent to the audience close to the stage 20 50 100 200 500 1K 2K 5K 10K 20K Hz LIMITED WARRANTY Proel warrants all materials workmanship and proper operation of this product for a period of two years from the original date of purchase If any defects are found in the materials or workmanship or if the product fails to function properly during the applicable warranty period the owner should inform about these defects the dealer or the distributor providing receipt or invoice of date of purchase and defect detailed description This warranty does not extend to damage resulting from improper installation misuse neglect or abuse Proel S p A will verify damage on returned units and when the unit has been properly used and warranty is still valid then the unit will be replaced or repaired Proel S p A is not responsible for any direct damage or indirect damage caused by product defectiveness e This unit package has been submitted to ISTA 1A integrity tests We suggest you control the unit conditions immediately after unpacking it e If any damage i
13. ew generation of CLASS D power amplifier with digitally controlled SMPS The DA module employed for powering the AX2065A delivers in an ultra compact package a maximum power of 2000W and each AX2065A is able to power an additional passive AX2065P module through the available power output on the back panel This feature will allows to assemble very competitive hybrid solutions both for rental and installation applications TECHNICAL SPECIFICATION Acoustical Remote Controls PRONET control software Line Array Element Network protocol CANBUS System type Short Transmission Line LF Back Loading Class D with Variable Switching Frequency Acoustic Transmission Line HF Waveguide Amplifier Type and SMPS Two 6 5 165 mm 1 5 38 mm aluminium Output Power 2x 1000 W Low frequency transducer voice coil 16Q each paralleled Mains Voltage Range Vac 230 V 15 or 115 V 15 50 60 Hz One 1 4 driver 2 5 64 mm edgewound Mains Connector PowerCon NAC3MPA NAC3MPB High frequency transducer voice coil titanium diaphragm Consumption 700 W nominal 1700 W max 8Q each paralleled IN OUT Connectors Neutrik XLR M XLR F Speakon NL4MP Frequency response 3 dB 80 Hz 18 kHz Processed IN OUT Network Connectors ETHERCON NE8FAV Horizontal Coverage Angle 110 6 dB Mechanical Vertical Coverage Angle 12 6 dB Width 583 mm 22 95 Maximum Peak SPL 1m 129 dB Height 244 mm 9 60 Electrical Depth 481 mm 18
14. ext one left free These operations ensure that every device has it s own unique ID if you need to add a new device to the network you simply repeat the operation of step 4 Every device maintains its ID also when it is turned off because the identifier is stored in the internal memory and it is cleared only by another Assign ID step as explained above This means that if your network is made always of the same devices the assigning ID procedure must be executed only the first time the system is turned on For more detailed instruction about PRONET see the PRONET USER S MANUAL included with the software EXAMPLE OF PRONET NETWORK WITH AX2065A AND SW215A PC NOTEBOOK USB2CAN ae USB 2 0 port 2S vec network a not pressed last device ouT NETWORK t network ouT NETWORK AX2065A D Gus TERMINATE er rT rE aTh l AX2065A aE ASA Fm JP ve i D le SW215A Useful tools to set up properly a vertical array system This is a list of tools that can be very useful to set properly a vertical array system CABLE TESTER It is a good practice to check all cables before each installation because even one faulty cable can compromise heavily the system performance INCLINOMETER WITH LEVER This tool can be use
15. nly M10 foot for stacked installation Pole Adaptor 0 to 10 tilt adaptor Sub Speaker 635mm Pole with M20 screw MAX 2x AX2065 KP010 O E50 O mlO Neutrik Powercon BLUE SOCKET Neutrik Powercon WHITE SOCKET Locking Pin for AX2265 Straight Shackle 16 mm for Fly bar Power amplifier module with mechanical assembly 1x SW215 91DSPKT3 98AXM6W16 98DRI2065 98MBN2065 AXIOM KPAX265 DHSS10M20 Input amp DSP module with panel assembly 6 5 woofer 1 5 VC 1 4 2 5 compression driver titanium diaphragm for 1 4 driver 24 4 cm 9 60 I O AND CONTROL OPERATIONS MAINS OUT MAINS IN Powercon NAC3FCA power input connector blue To switch the amplifier on insert the Powercon connector and turn it clockwise into the ON position To switch the amplifier off pull back the switch on the connector and turn it counter clockwise into the POWER OFF position WARNING In the case of product failure or fuse replacement disconnect the unit completely from the mains power The power cable must only be connected to a socket corresponding to the specifications indicated on the amplifier unit The power supply must be protected by a suitably rated thermo magnetic breaker Preferably use a Suitable switch to power on the whole audio system leaving the Powercon always connected to each speaker this simple trick extend the life of the Powercon connectors INPUT MAINS
16. ormation When loudspeaker arrays are flown in an open air environment possible wind effects must be taken into account Wind load produces additional dynamic forces acting on the rigging components and the suspension which may lead to a dangerous situation If according to the forecast wind forces higher than 5 bft 29 38 Km h are possible the following actions have to be taken The actual on site wind speed has to be monitored permanently Be aware that wind speed typically increases with height above ground Suspension and securing points of the array should be designed to support double the static load in order to withstand any additional dynamic forces WARNING A N Flying loudspeakers overhead at wind forces higher than 6 bft 39 49 Km h is not recommended If the wind force exceeds 7 bft 50 61 Km h there is a risk of mechanical damage to the components which may lead to a dangerous situation for persons in the vicinity of the flown array Stop the event and make sure that no person remains in the vicinity of the array Lower and secure the array AXIOM Stacked installation KPTSW215 STACKED ARRAY WARNING A N e The ground where the KPTSW215 Fly bar serving as ground support is placed needs to be absolutely stable and compact e Adjust the feet so to lie the bar perfectly horizontal e Always secure ground stacked setups against movement and possible tipping over e A maximum of 4 x AX2065 cabinets with the KPTSW215
17. rter the other side must be terminated pressing the TERMINATE switch on the last device All devices between these two points must have the TERMINATE switch lifted Assign the ID number To work properly in a PRONET network each connected device must have a unique identifier number called ID By default the USB2CAN PC controller has ID 0 and there can be only one PC controller Every other device connected must have its own unique ID equal or greater than 1 in the network cannot exist two devices with the same ID An ID number is assigned automatically to each devices when they are turned on for the first time connected to a network In order to correctly assign a new available ID to each device for working properly in a Pronet network follow these instructions 1 Switch off all the devices AXIOM 2 Connect them correctly to the network cables 3 TERMINATE the latest device in the network connection 4 Switch on the first device keep pressed PRESET button on the control panel 5 Leaving the previous device switched on repeat the previous operation on the next device until the latest device is turned on The Assign ID procedure for a device makes the internal network controller to perform two operations reset the current ID search the first free ID in the network starting from ID 1 If no other devices are connected and powered on the controller assume ID 1 that is the first free ID otherwise it searches the n
18. s Thanks to a suspension mechanism designed to be functional flexible and safe each system must be suspended or stacked using the KPTSW215 fly bar The loudspeakers are linked together in a column using a series of couplers integrated in the frame of each enclosure Each system is set up properly both acoustically and mechanically only using the aiming software Coupling system in the front does not require any adjustment using two locking pins each loudspeaker box is fixed to the previous The slotted bar in the back is inserted in a U shaped frame which features a series of numbered holes Sliding the slotted bar in the U shaped frame of the next loudspeaker and inserting a locking pin in one of the numbered holes it is possible to adjust the relative splay angle between two adjacent loudspeakers in the array column KPTSW215 fly bar maximum capacity is 540 Kg 1190 Ibs with the 0 angle It can support with a safety factor of 10 1 up to A N e 8 AX2065A 8 AX2065P flybar from 0 to 10 e 12 AX2065A flybar from 0 to 10 KPTSW215 FLY BAR ASSEMBLY SEQUENCE e 2 SW215AF 4 AX2065A 4 AX2065P flybar at 0 S e 2 SW215AF 8 AX2065A flybar at 0 e 6 SW215AF flybar from 0 to 5 Follow the sequence in the figure for fixing the fly bar at the first box Usually this is the first step before lifting up the system Be careful to insert properly all the locking pins 1 2 and 3 4 then the shackle 5 in the right holes as specified
19. s found immediately advise the dealer Keep all unit packaging parts to allow inspection e Proel is not responsible for any damage that occurs during shipment e Products are sold delivered ex warehouse and shipment is at charge and risk of the buyer e Possible damages to unit should be immediately notified to forwarder Each complaint for package tampered with should be done within eight days from product receipt SAFETY INSTRUCTIONS To reduce the risk close supervision is necessary when the product is used near children Protect the apparatus from atmospheric agents and keep it away from water rain and high humidity places This product should be site away from heat sources such as radiators lamps and any other device that generate heat This product should be located so that its location or position does not interfere with its proper ventilation and heating dissipation Care should be taken so that objects and liquids do not go inside the product The product should be connected to a power supply mains line only of the type described on the operating instructions or as marked on the product Connect the apparatus to a power supply using only power cord included making always sure it is in good conditions WARNING The mains plug is used as disconnect device the disconnect device shall remain readily operable Do not cancel the safety feature assured by means of a polarized line plug one blade wider th
20. ta that defines the Line Array with regard to its possible configurations as well as to its geometrical and acoustical properties For detailed explanation of how to use the software and how to obtain a correct aiming refer to EASE Focus documentation and other on line manuals http focus afmg eu index php fc software en html t WARNING CAREFULLY READ THE FOLLOWING INSTRUCTIONS AND CONDITION OF USE e This loudspeaker is designed exclusively for Professional audio applications The product must be installed by qualified personal only e Proel strongly recommends that this loudspeaker cabinet be suspended taking into consideration all current National Federal State and Local regulations Please contact the manufacturer for further information e Proel do not accept any liability for damage caused to third parties due to improper installation lack of maintenance tampering or improper use of this product including disregard of acceptable and applicable safety standards e During assembly pay attention to the possible risk of crushing Wear suitable protective clothing Observe all instructions given on the rigging components and the loudspeaker cabinets When chain hoists are in operation ensure that there is nobody directly underneath or in the vicinity of the load Do not under any circumstances climb on the array KPTSW215 Fly Bar and accessories The AX2065 Systems are built to allow the suspension of array with variable shape and dimension
21. the unit ON you can select the DSP PRESET The selected PRESET is indicated by the corresponding LED STANDARD This PRESET is suitable for vertical flown arrays that may range from 4 to 8 boxes or for the centre region of a bigger flown array IN OUT It can be used also for stacked arrays NETWORK LONG THROW This PRESET can be used in arrays bigger than 6 or 8 boxes and loaded in the top 1 or 2 boxes in order to obtain a more even distribution of the sound pressure especially if they point very far away or to the upper deck of a large theatre SIGN LIMIT DOWN FILL This PRESET which features a much smoother high frequency response can be loaded in the bottom boxes usually 1 or 2 SINGLE BOX boxes of a large flown array in order to reach conveniently the audience close to the stage This preset could be very useful also when the box is used just on its own as a Front Fill element in the front of very large stages USER This LED lights when the USER PRESET is loaded This preset corresponds to USER MEMORY no 1 of the DSP and as a factory setting it s the same to STANDARD If you want to modify it you have to connect MF gt 1 1 the unit to a PC edit the parameters with PRONET software and save the PRESET into USER MEMORY no 1 Note see also the PRONET example further on this manual HF gt 2 2 NETWORK IN OUT These are a standard RJ45 CAT5 connectors with optional NEUTRIK NE8MC RJ45 cable connector carrier used for PRONET

AX2065A

Contents

Download Pdf Manuals

Related Search

Related Contents