Users manual
Contents
1. Breathing of gaseous LPG causes after some time of action headache nausea weariness dissipated attention drowsiness If not ignited the gaseous LPG may cause suffocation of the operators though it is not poisonous directly like e g the city gas As it is heavier than air it is accumulated close to the earth and in the recesses and the laying person lost consciousness in case of injury etc may occur in the oppressive atmosphere Gaseous LPG also causes skin degreasing The liquefied LPG is evaporated after the steep drop of overpressure to the atmospheric pressure e g leak of the liquefied LPG out of the device by boiling under the temperature of 42 C and therefore contact of the skin with the liquefied LPG results in frostbites USER MANUAL 18 2 DW LPG DISPENSERS SHARK 1 LPG Dispensers TATSUNO BENC 1 1 Basic Specifications Dispensed medium liquid propane butane Max flow rate Qmax 50 dm min Min flow rate Qnin 5 dm min Min volume of refueling V min 5 dn Operating pressure p 1 6 MPa Max operating pressure Pmax 1 8 MPa Rated pressure PN 2 5 MPa Accuracy of dispensing 1 Operating temperature of the ambient air 30 50 C Operating temperature of the medium 20 50 C Electronic calculator Power 230 V 10 15 50 Hz 5 Hz max 84 VA 2 Basic Functions and Dispenser Setting Setting of the LPG dispensers is done by the set of parameters by which functional dispenser par2. Enter gt the operation is permitted Preset depressing of corresponding preset T Direct switching to the parameter with preset uid key No 1 CZK 100 lt 0 gt az lt 9 gt number Preset depressing of corresponding preset 5 key No 2 CZK 10 lt REG gt End of selected mode lt 6 gt Cancel of preset on one fuel dispenser side CHANGE OF PARAMETER VALUE AND LOADING OF preset key No 5 Cancel ACCESS lt 7 gt Lighting fuel dispenser ON 0 a2 9 Loading of value of the edited digit and Switching to the next figure 8 Displa ying a Powered CNG qus volume tne lt gt Increase of value of just edited parameter digit function is activated 9 Lighting fuel dispenser OFF Shift lt gt dm of value of just edited parameter lt Next gt Switching to editing of the next parameter digit START OF SETTING MODES lt Shift gt lt Next gt d to editing of the previous parameter Shift REG Commences the operator mode lt Enter gt End of change and loading of a new value lt REG gt Gommences Uie manager mode Upon loading lt Shift gt lt Enter gt End of change w o loading of a new value the password USER MANUAL 18 2 DW LPG DISPENSERS SHARK 2 1 2 Setting of Parameters on Dispenser with Fuel Volume Display The process of setting is similar to that of the classic three line display only functions of certain keys on the remote controller keyboard differ Basic principles of setting in th
3. display side A B 0 code of the last tenth error of the dispenser on display side B A 1 code of the last but one ninth error of the dispenser on side A B 1 code of the last but one ninth error of the dispenser on side B A 9 code of the error first in the history of the dispenser on side A B 9 code of the error first in the history of the dispenser on side B 12344 5 2304 00 kr 06A0 Vic 12 2 1 5 7 Displaying of History of Dispensing code 07 The function serves for displaying of the history of the latest 10 dispensing transactions on each side realized on the dispenser Data layout of this parameter on the display is as follows 5000 12344 5 J vii 2304 00 ko 07A0 vc 20 00 A Price Fuelling Time Fuelling Date Parameter aux code item number description A 0 last transaction tenth on side A B 0 last transaction tenth on side B A 1 last but one transaction ninth on side A B 1 last but one transaction ninth on side A gt transaction first in the sequence on side A B 9 transaction first in the sequence on side B The first and second line contain price cash amount and dispensed volume The unit price of the transaction with the parameter number and the auxiliary code with the item number take turns on the third line Number of the item means position in the history of transactions 0 is the last newest transac
4. in the boot After the manager mode is recalled the display shows the prompt for loading the 4 digit access password To have the password secret the loaded digits are displayed as points The manufacturer has set the access password 1111 Example Depress the keys lt 1 gt lt 1 gt lt 1 gt lt 1 gt and lt Enter gt After the valid password is loaded the display shows the parameter number 00 by depressing the key lt Enter gt you can continue by automatic switching to the parameter No 01 or it is possible to load the parameter number and lt Enter gt for direct switching to the requested parameter After the manager mode is recalled value of the first parameter will be displayed Cg USER MANUAL The manager mode enables to display and change set the following parameters EE Non resetable totalizers e LE EES Daily totalizers 12 Fueldispenser operating mode Current time and date Current operating temperature Version of program and CRC number 11 12 History of failures Operating check number 19 1 2 4 5 Reset of daily totalizers 6 ily totali i i O7 i 07 08 Accesspassword 09 Historyofmaintenance 1 9 Displayngofdispaysegmentemor 10 unued ll Parameters marked by asterisk can be viewed only in the manager mode not set The manager mode is ended by depressing the key REG on the remote controller The mode is also ended automati
5. lamps When raising possible claims the following data have to be specified e Serial number and name see the rating plate e Precise description of fault and the circumstances under which the fault occurred The claim will not be acknowledged provided that damaged seals or non permitted intervention into the unit were established Defects and drawbacks following from incorrect operation inspection and maintenance of the fuel dispenser or its functional assemblies are out of scope of the warranty e g the problems caused by presence of water and impurities in the tank and the hydraulic system Check for presence of water and impurities and possible cleaning is necessary in the course of operation 4 4 Accessories e Installation and User Manual e Certificate of Quality and Completeness e Certificate of Conformity e Pressure Test Report e IR controller for operation and programming of the calculator for the BG PDE el calculator e Foundation frame a special order 21 USER MANUAL ithe DW LPG DISPENSERS SHARK 5 Declaration of conformity 5 1 Fuel Dispensers line BMP500 S LPG QPP LAPP LLL LLL AL AAPL PPL PLL LLLP LPPLL IY ESOSLEN_S VI TATSUNO BENC EUROPE a s TATSUNO Pra sk 2325 68 678 01 Blansko Czech republic Registration No 26221454 ES DECLARATION OF CONFORMITY Hereby we declare that the product Electronic Fuel Liquefied Petroleum Gas Dispensers Type series BMP 5XX S LPG Purpose and scope of produ
6. permanent damage of lacquers of untreated body parts and or to intercrystalline corrosion guards made of stainless steel Regular maintenance of fuel dispenser body is carried out by water and or by solution of detergents and available car cosmetic preparations Owner of the fuel dispenser shall e Appoint one staff member liable for operation and workability of the fuel dispenser e Provide inspections testing repairs and maintenance by the professional method e File documents and operating records e An and all activities connected with operation and service of the LPG fuel dispenser may be carried out only and exclusively by the staff with relevant authorization 20 Principles of LPG Fuel Dispenser Checking Check of equipment tanks pipe distribution lines and fuel dispensers are carried out with the periodicity fixed by the bylaws of the filling station in accordance with the valid regulations e Check the fuel dispenser hydraulic system for tightness by soap solution e Check of machinery equipment e Check of non return and safety valve for correct functioning e Inspection calibration and official verification of the LPG fuel dispenser is carried out by the relevant institute abroad e The inspection is preceded by cleaning of the whole device clearing the tanks of dust water and other impurities Fuel Dispenser Error Messages Defect of the fuel dispenser leads to locking of the operation of refueling and to displ
7. the position ON 2 1 5 11 Error Statistics code 13 The function serves for displaying statistics of the errors which took place on the fuel dispenser since the moment of initialization or resetting of the electronic calculator This parameter has differing data arrangement on the display Error frequency Parameter The first and second line contain the fault code and the frequency rate of the fault in question 2 1 5 12 Current Operating Temperature code 14 The function displays the current temperature measured by the temperature sensor placed on the processor board e line 1 Amount operating calculator temperature e line 2 Litres temperature of the product 1 2 3 or 4 only if the temperature sensors are installed 14 2 1 5 13 Daily Totalizer Resetting code 15 The function serves for resetting of all daily totalizers registers of the dispensing hoses After setting the parameter value to 1 and after confirmation all totalizers will be reset 2 1 5 14 Operating Check Number code 16 The function serves for displaying of the 6 digit operating check number and for operating code loading e line 1 Amount operating check number 2 1 5 15 Text messages code 18 If the fuel dispenser is equipped by the alphanumeric display the function enables to set the text messages which will appear on the alphanumeric display 2 1 5 16 Displaying of Display Segment Error code 19 The function enables dis
8. A AAA AAA LAP ALAAALLL ALD LDA AAA AAA AAA OOOO K AAAS AAAS SAA NNN NNN 22 5 2 Fuel Dispensers line BMP2000 S LPG REENEN ES20LEN S VI TATSUNO BENC EUROPE a s TATSUNO Pra sk 2325 68 678 01 Blansko Czech republic Registration No 26221454 ES DECLARATION OF CONFORMITY Hereby we declare that the product Electronic Fuel Liquefied Petroleum Gas Dispensers Type series BMP 2XXX S LPG Purpose and scope of product use The equipment serves for pumpinc Complies with the technical requirements contained in the ical standard and regulations of the EC Directives Equipment and protective systems inten for use in potentially explosive atmospher 94 9 EC The producer certifies hereby Ei that properties of the above mentioned cet and all requirements set by the quoted technical standards and the EC Di above and the equipment is safe for the specifie We have adopted the measures by which conf rmity of commi documentation and basic requirements is provid The said equipment was certified as the produc by The Physical Technical 1 esting Institute Ostrava Radvanice notified body number 1026 On the basis of carried out certification th entificate No FTZU 03 ATEX 0025 was issued on 5 of May m Place and Date of issue Name and Signature of the autheriz TT EUROPE 6 78 OF Blaniko 2 MBOX 49 Cresh R e moii banc bea D L nun Se ur aue Gier Katalog QS do
9. TATSUNO TATSUNO BENC EUROPE A S Fuel Dispensers of liquefied petroleum gas BMP500 S LPG and BMP2000 S LPG version SHARK User Manual TATSUNO BENG EUROPE a s 25 08 2005 UP021 EN USER MANUAL Lex UW LPG DISPENSERS SHARK Fuel Dispensers of Liquefied Petroleum Gas BMP500 S LPG and BMP2000 S LPG version SHARK TATSUNO BENC EUROPE a s Prazsk 2325 68 e 67801 Blansko Tel 420 516 428411 Fax 420 516 428410 Czech Republic e mail benc benc cz http www benc cz ATSUING C Bene Copyright Neither the manual in full nor any part of it may be reproduced without the explicit approval of TATSUNO BENC EUROPE a s LIST OF CONTENTS 0 INTRODUCTORY INFORMATION 0 cscsscsscsssscsscssccscsssesssscsssssessssessnesencsseessesssessssscsssnsesnsesssessessessoess 4 0 1 READ THE MANUAL THOROUGHLY Per 4 0 2 BRIEF CHARACTERISTICS OF THE USED MM 5 1 LPG DISPENSERS TATSUNO BEN eener 6 Lil s BASIC SPECIFICATIONS eeh tr PE E e Re orte pr e AE SS 6 2 BASIC FUNCTIONS AND DISPENSER SETTING eeeeeeeee eese e enses tnn tn netus tassa seta seta sees ses sens snnee 6 2 T PDE CAECULATOR E derer EE Ibat OO E IIS 6 2 4 1 Remote Fuel Dispenser Control eet o ie ee e th tee euet ete e e To vore 7 2 1 2 Setting of Parameters on Dispenser with Fuel Volume Display eene amp 2 1 3 Data Monitoring in Setting Modes enrii a e Eii aa a aE E a Ea E EERTE 8 244 TE 9 2 1 5 Maria
10. ables displaying of the display segment error El by the processor FI eh Description value 0 Do not display the error of the display segment 1 Display the error of the display segment default setting 2 2 Calculators Puma HT TE and Puma MPD The calculators Puma HT TE and Puma MPD produced by the company Gilbarco Veederoot S p A the former company Logitron are set by the three key keyboard Functions of the keys are as follows Key Function Entry into the price setting mode after calculator switching lt gt A Selection of figures on the unit price display lt gt Value increase Price setting for manual mode Unit price setting is done in the manual mode namely as follows e switching the calculator ON OFF e display mask removal depressing the key lt gt the calculator is switched to the price setting mode e selection of the figure for the price the value of which is to be changed by the key lt gt e setting of the value of the selected figure by the key lt gt e display mask mounting e switching the calculator ON OFF Setting or monitoring of parameters This operation is reserved to service technicians servicemen only 15 7 e gt USER MANUAL Bent 3 3 Calculators ADP M and ADPMPD M The calculators ADP and ADPMPD produced by the company Beta Control s r o are set using the IR manager keyboard KL MANINF provided with four keys
11. after 10 seconds irrespectively of the control button The data remain displayed on the calculator The fuel dispensers equipped by electronic pre selection enable to preset precise requested amount determined by volume or by price These fuel dispensers ate equipped by the double stage electromagnetic valve DUTIES OF LPG FUEL DISPENSER OPERATOR e Adhere to the bylaws and operation manuals of gas appliances e Maintain the operated device in safe and workable state e Notify any fault defect unusual phenomena revealed during operation to the filling station owner immediately e Put the device out of operation in case of gas leak or another danger e Keep the device in order and clean and prevent unauthorized persons from access e Notify the events making the operator s work problematic difficult to the owner e Record the data concerning start and end of every shift inspections repairs and reviews duly into the operating log book e Operator of the fuel dispenser and fuel tank may neither carry out any repairs by himself nor change setting of the equipment or safety fittings OPERATOR S OUTFIT e soap foamy solution brush for detection of leaks leather gloves e the first aid kit log book writing utensils operating and safety rules wiring diagram of the fittings and fire extinguisher must be available in the filling station kiosk 3 3 2 Safety of LPG Fuel Dispenser Operation Owner of the filling
12. ameters can be controlled mode and behaviour of the dispenser in different situations changed materially Values of the parameters can be monitored and changed either by the remote IR controller or by the functional keys placed directly on the calculator or on a simple keyboard being the integral part of the calculator assembly Method of setting of the fuel dispenser differs depending on the type of the used calculator placed in the dispenser head The section below describes basic functions and setting for the calculators PDE Puma HT TE Puma MPD ADP and ADPMPD 2 1 PDE Calculator The calculator PDE manufactured by the company TATSUNO BENC EUROPE a s is set by the remote IR controller marked PDERT The setting mode serves for monitoring and change of the parameters and provides the following operations e displaying of non resetable electronic volume and cash amount totalizers of all hoses e displaying and reset of daily electronic volume and cash amount totalizers of all hoses e setting of unit product prices manual mode e sctting of different functional parameters of the dispenser The setting mode can be recalled on the dispenser by the method below only if the dispenser is at rest completed dispensing all nozzles are accommodated in the boots There ate two setting modes available e Operator mode specified for filling station operators the operator can only read values of electronic totalizers and values of
13. aying of the error message on the fuel dispenser display Nearly all error messages may be cleared by nozzle release and back suspension by switching the electronic unit feeder ON OFF and or by depressing 0 on the remote controller only the PDE electronic unit 4 2 LPG Fuel Dispenser Service e setvice operations are carried out in conformity with the operation rules of the filling station e prior to start the works the fuel dispenser must be put out of operation the fuel dispenser must be affixed by a visible label OUT OF OPERATION and the approach lane must be marked by the sign NO ENTRY e the fuel dispenser must be disconnected from the power source switching OFF the master switch in the switchboard e propane butane must be forced out of the whole system incl the fuel dispenser except for the tank by nitrogen prior to start any works e valves on the supply and return piping must be closed fully e traffic of the vehicles must be prevented at the distance of 5 m round the fuel dispenser in the coutse of setvice activities e fire extinguisher must be available for the staff e the service intervention must be carried out by the trained staff of the service company 4 3 Warranty and Complaints The contractual warranty is determined the manufacturer warrants for the supplied unit for 2 years or 1 million liters of dispensed medium as a standard The warranty does not cover the consumables e g the tubular discharge
14. basic dispenser parameters The operator can neither reset nor change their values e Manager mode specified for the filling station managet The manager is authorized both to read the values reset daily totalizers and to set basic operating parameters of the LPG dispenser The manager must load the access password to be able to work in the manager mode 2 1 1 Remote Fuel Dispenser Control A special remote IR controller must be used for reading dispenser values totalizers change of the dispenser mode or for setting different calculator parameters on the LPG dispensers equipped by the PDE calculator The Remote controller keyboard had the following keys and their layout Key function key function OPERATING STATE Release of dispenser side after payment or CALCULATOR PARAMETER READING lt Shift gt lt Enter gt failure lt Next gt Switching to next parameter Release of both sides whole fuel dispenser n 0 after payment or failure lt Shift gt lt Next gt Switching to previous parameter Preset depressing of corresponding preset S 1 key No 3 10 litres lt gt Switching to next parameter item Preset depressing of corresponding preset f 2 key No 4 1 litre Shift lt gt Switching to previous parameter item d Changed value of the displayed parameter if 3 Displaying of the latest refilling on the display lt
15. cally if no key is depressed for 60 seconds 2 1 5 1 Non resetable totalizers code 01 Electronic totalizers of all hoses meters are stored in electronic calculator memory These totalizers are non resetable and show how many litres were dispensed by individual hoses item number description 1 volume dispensed by the hose 1 in litres 2 volume dispensed by the hose 2 in litres 9 volume dispensed by the hose 9 in litres H volume dispensed by the hose 10 in litres 2 1 5 2 Daily totalizers code 02 The electronic daily totalizers of all hoses meters ate stored in electronic calculator memory These totalizers can be reset at any time manager mode parameter 15 The daily totalizers show what fuel volume cash was dispensed by individual hoses since the latest resetting aux code item number description L 1 volume dispensed by the hose No 1 in litres A 1 amount dispensed by the hose No 1 in currency L 2 volume dispensed by the hose No 2 in litres A 9 amount dispensed by the hose No 9 in currency L H volume dispensed by the hose No 10 in litres A H amount dispensed by the hose No 10 in currency 2 1 5 3 Fuel Product Unit Prices code 03 The function enables to display and set current unit prices of all fuel products i e prices per 1 litre of fuel sold for cash item number description default setting 1 unit price of product 1 00 00 2 unit
16. ct use The equipment serves d petroleum gas Complies with the technical requi ents contai n th d technical standard and regulations of the EC Directivesz pa by P 7 e Equipment and protective systems intended for use in potentially exp osive atmosphere 4 9 EC Electromagnetic compatibility 89 336 EC CSN EN 50081 1 1994 CSN EN 50082 1 1999 OIML R 118 part 4 4 4 5 4 6 4 7 4 8 CSN EN 60204 1 2000 The producer certifies hereby that properties of the above ned equipment meet and all requirements set by the quoted technical standards and the ECsDirectives above and the equipment is safe for the specified scope of use We have adopt led the measures by which conformity of commissioned equipment with technical documentation and basic requirements is provided and guaranteed d as the product bysThe Physical T chnical Testing Institute Ostrava The said equipm nt was certifi Radvanice notified body ndmber 1026 On the basis of c rried ouf certification the Type Certificate No FTZU 03 ATEX 0025 was issued on May 5 2003 EMC was verifi technical Test Institute No 3018 I and the Certificate No 1012139 on November 22 2001 Blansko January 5 2005 TATSUNO ENC EUROPE rafsha 65 674 O1 bisnnhe 2 Po BOX 49 Crech Republic Le 262114534 Maren 10556 105 e 420 50A 428410 QS dokument amp ESOSLEN_S Vi pdf Katalog APP AP SA AAA ALLL AAA AAA AA
17. e manager and setvice mode 1 The manager mode is entered by depressing the key lt REG gt The word CODE appears for ca 1 second on the display Now the password must be loaded After loading the correct password and confirmation by the key lt Enter gt the volume display will shown 0 and the dispenser waits for loading the relevant parameter digit 2 Switching between the parameters by the keys lt Next gt and lt Shift gt lt Next gt between sub parametets by lt gt and Next lt gt 3 To display value of the parameter on the line Litres fuel volume depress the key 1 To display value of the parameter on the line Price cash amount depress the key lt 2 gt The key Shift lt Enter gt again displays the number of the parameter i e displays the line K litr unit grade price 4 Change editing of parameter value by the key Enter 5 Mode exit by the key lt REG gt Viewing of the parameters totalizers in the operator mode is done in the same way When depressing the key Shift lt REG gt the first parameter 01 will appear automatically Switching between the parameters by the keys lt Next gt and Shift lt Next gt between sub parameters by lt gt and Shift lt gt By depressing the keys lt 1 gt and 2 parameter values can be monitored Operator mode exit by depressing the key lt REG gt 2 1 3 Data Monitoring in Setting Mode All data in
18. ed e feeding of valve switching 230V non stabilized All points above are protected by relevant circuit breakers by which the fuel dispensers are switched ON OFF LPG dispensers with calculators Puma HT TE and Puma MPD have only the outlet for electronic calculator feeding 230V stabilized in the main switchboard 17 CE USER MANUAL D Ce LPG DISPENSERS SHARK 3 3 Operation of LPG Fuel Dispenser Prior to start refueling the fuel dispenser operator shall check whether the tank has the homologation mark and whether the motor and el equipment of the vehicle are switched off The operator also inspects state and or wear of the filler which might cause gas leaks If serious defects are revealed the operator may reject tank refueling In case of gas leaks or any danger the operator stops refueling 3 3 1 Vehicle Refueling by LPG Operation of the fuel dispenser itself is provided by the filling station staff who releases the nozzle from the fuel dispenser and connects it with the fuel tank of the vehicle which must be braked reliably When depressing the control button on the calculator box the el calculator is reset and the pump el motor placed next to the standby fuel reservoir started Refueling can be stopped at any time be releasing the control button When filling the full tank the filling tank neck is closed as soon as 80 of the tank volume is refueled and the safety controller el calculator interrupts refueling
19. eese eene enne en rennen nenne tenete nen nennen nenne 22 5 2 FUEL DISPENSERS LINE BMP2000 S LPG craro eere se eene enne nein en eene netten entren nennen nenne 23 CER yN USER MANUAL 7 LPG DISPENSERS SHARK 0 Introductory Information 0 1 Read the Manual Thoroughly First Read the relevant parts of the User Manual prior to start installing or operating the fuel dispenser Consider all hazards attentions and notes contained in the Manual The Manual worked out by the manufacturer is the integral part of fuel dispenser accessories The user is liable fully for use of the Manual any and all operations not described here shall be considered forbidden The operator carrying such operations shall be liable fully for consequences of his her actions Each fuel dispenser has been tested from the points of its function safety and metrology by the manufacturing plant Delivery of each individual fuel dispenser is accompanied by the certification documents which shall be submitted to the competent authorities by the user if asked to do so e The equipment has to be installed by the staff qualified and authorized pursuant to relevant standards regulations local limitations and pursuant to the Manual e Smoking and open fire handling is prohibited in the vicinity of the dispenser e Always adhere to the rules for LPG handling e Monitor all leaks in the dispenser Should you establish fuel leaks disconnect power supply line and contact
20. en tren trente enne en eene innere tnne tenete 17 3 2 PUTTING LPG DISPENSER INTO OPERATION enne nene teen nhen trennen reete enne rennen nennen 17 3 3 OPERATION OF LPG FUEL DISPENSER poisas sets eseese esene enne eSEE EEE E trennen eren enne EEE eter tenete 18 3 341 Vehicle Refueling DY LPG nn eb dg eer ee DEE Ee 18 3 3 2 Safety of LPG Fuel Dispenser Operation eese eene teen rene rennen ener 18 3 3 3 Pre selection Keyboard d a edm eee pete reel Tg pu M ete ee 19 3 3 4 Electromechanical LitreTotalizers eae o ee tiene eee ENEE Nee 19 3 3 5 Fuel Dispenser Display Back lighting eee eee eese 19 3 3 6 Signaling Diode SIG on the Display derenan piii n e eee enne enne nennen a a a 19 3 3 7 Signaling Diode PWR on the Display AEN 19 4 MAINTENANCE AND SERVICE eerie eene enses n ense natuss tn netus tasa tasa tosta sets sts sens sens enne en netus s taste ann 20 4 1 SURVEY OF MAIN PRINCIPLES OF LPG FUEL DISPENSER MAINTENANCE ceceeeeeeeeeeenen eene een rennen 20 4 2 LPG FUEL DISPENSER SERVICE a edeettolp ee eonim eee rt e A ie e etui 21 4 3 WARRANTY AND COMPLAINTS trennen nennen eene EE enne tene tnee tene tene E tester en nennen enne 21 AA ACCESSORIES 5nd eso i eme boda estesa e 21 5 DECLARATION OF CONFORM ITY eeeeeeee eee eene en estas tns ta seta stes stas tn stes sts sens sens ense ense sn netus seta sna 22 5 1 FUEL DISPENSERS LINE BMP500 S LPG
21. er is subject to the error message E 18 which appears on the display If value of the parameter equals to 1 the fuel dispenser is operated in the manual mode see the mode No 3 until it is connected to the master computer Then the computer is switched automatically to the automatic mode see the mode No 1 Interrupted communication between the computer and the fuel dispenser is subject to the error message E 18 which appears on the display If value of the parameter equals to 2 the fuel dispenser is operated in the manual mode see the mode No 3 until it is connected to the master computer Then the computer is switched automatically to the automatic mode see the mode No 1 Unlike the mode 2 the fuel dispenser is locked after each transaction and has to be unlocked by the magnets or by the remote controller by depressing the key 0 Interrupted communication between the computer and the fuel dispenser is subject to the error message E 18 which appeats on the display e If value of the parameter equals to 3 the fuel dispenser is operated in the pure manual mode The fuel dispenser is independent fully cannot be connected to the computer Unit fuel prices may be set by the fuel dispenser parameter No 3 If value of the parameter equals to 4 the fuel dispenser is operated in the credit mode The fuel dispenser may be switched to this mode only if the fuel dispenser is equipped by the credit module PDECRE and the switch cash Credit is in
22. ger Mode ise metere ae eGR AE EAE eee ATE 9 2 1 5 1 Non resetable totalizers code OI 10 2 1 5 2 Ddily totalizers code 02 i cece t SR d e der SR RETE pe eda ees 10 2 1 5 3 Fuel Product Unit Prices code 03 esses eee eene enne nennen enne E R 10 2 1 5 4 Current Time and Date code 04 n urra maenna i i E E E A tenente seen entes entretenir 12 2 1 5 5 Displaying of Program Version and Check Sum code 05 eene 12 2 1 5 6 Displaying of Latest Error Conditions of Fuel Dispenser code UO 12 2 1 5 7 Displaying of History of Dispensing code UI 13 231298 Access Password code EE 13 2 1 5 9 History of Maintenance code 09 eese eene ene tnnt nennen enne nein tenerent enne 13 2 1 5 10 Operating Fuel Dispenser Mode code 12 eee eere 13 2d Tl ErrorStausties code T3 EE 14 2 1 5 12 Current Operating Temperature code 14 eee esee eren enne 14 241 5 13 Daily Totalizer Resetting Code I5 5 e pe D e rU IR gin erbe big d 15 2 1 5 14 Operating Check Number code Jl 15 24 3 15 Text messages code 18 oae a er Ce ace sun ie C ve EIS FO ge espe sep ges 15 2 1 5 16 Displaying of Display Segment Error code 19 esee eee eene 15 2 2 CALCULATORS PUMA HT TE AND PUMA MI 15 3 3 CALCULATORS ADP M AND ADPMPD M AAA 16 3 ORERA wurenpe 17 3 1 INSTRUCTIONS FOR SAFE OPERATION essent emet nenne tene tr
23. hazard LPG is not poisonous but is suffocating In case of breathing failure carry out apply artificial breathing immediately In case of blood circulation failure combine artificial breathing with indirect heart massage Transfer the affected person the heath facility immediately Frostbites liquid LPG In case of steep drop of overpressure to the atmospheric pressure the liquid LPG is evaporated under the temperature of 42 C Leak of the liquid LPG may result in frostbites when in contact with the skin Do not rub the frostbitten parts of the body but cover by a sterile dressing and call the doctor Eyes affected by LPG shall be flushed by plenty of water Call the doctor Burns fire When burnt cool the injuty by cold water do not lubricate cover by a sterile dressing and call the doctor Do not remove the dress If the clothes are burnt do not run extinguish by water blanket by rolling about 3 3 3 Pre selection Keyboard The LPG dispensers TATSUNO BENC can be completed by the pre selection preset keyboard for presetting of the sum or volume directly on the fuel dispenser by the customer himself Prior to start refueling the customer can decide how much fuel or for what price he wants to refuel himself 3 3 4 Electromechanical Litre Totalizers The fuel dispensers TATSUNO BENC are equipped by electromechanical totalizers as the standard for monitoring of the total fuel volume dispensed by each hose The totalizers are placed o
24. izers for other nozzles will appear totalizer reading is ended by depressing the key lt 0 gt Setting or monitoring of parameters This operation is reserved to service technicians servicemen only 16 3 Operation 3 1 Instructions for Safe Operation Technical and technological equipment must comply with the approved conditions which comprise the instructions for safe operation and maintenance as well as solution of emergency states Snow fire extinguishers must be available close to the device in conformity with the fire safety rules Only the persons that have provably passed the training may operate the LPG pumping station The fuel dispenser is equipped by the STOP button for emergency situations the procedure in case of fire or emergency situation is determined precisely by the local bylaws the operator must be trained correspondingly The STOP line must be placed 5 m from the fuel dispenser as a minimum e LPG storage tanks pipelines and the dispenser must be earthed the earthing point for the road tanker must be marked explicitly e When refueling re pumping and emptying LPG the issued regulations have to be adhered to arrival and operation in the specified pumping station premises prevented according to the local conditions When selling and pumping LPG the determined procedure has to be adhered to in case of any danger the device must be put out of operation immediately When refue
25. kument amp ESZ LEN S VLpdf APAAA AAA AA Pr PS PS P PS P PSP PS PP Pr PS Pr PS PS PPS PP PSP PSP PPS PS P a mmu merda wma Fa ASAP APP AA Ap NNN NNN NNN N NNN NNN NNN NN NNN NN NNN NNN NNNSNN YNNN YNN YNNN AN 23
26. ling the operator of the pumping station must be present refueling is prohibited during storms danger of atmospheric discharges e It is necessary to keep the preset deadlines for regular inspections and checks of the complete installed unit intervention of the persons without relevant competence capability and qualification into the installed technology incl the gas appliance must be prevented safely e The operator may not carry out any repairs of the devices and change setting of the safety fittings Regular maintenance and service may be carried out by the authorized service company only e The operator shall keep the device in intact and safe state any defect or unusual phenomenon shall be notified to the service organization immediately in case of danger of delayed intervention the device must be put out of operation CAUTION e Smoking and open fire handling is prohibited in the vicinity of the dispenser e Smoking is prohibited also for the persons sitting in the car e tis prohibited to use the mobile phone in the vicinity of the dispenser e tis prohibited to dispense if the motor is running 3 2 Putting LPG Dispenser into Operation Switching the fuel dispenser ON OFF is carried out in the master switchboard of the filling station where fuel dispenser feeders are connected Each fuel dispenser has three power supply outlets in the master switchboard e feeding of electronic calculator 230V stabiliz
27. lt R gt 02 lt gt and lt gt Functions of the keys are as follows Key Function 0 Entry into the price setting mode after calculator switching lt gt Selection of figures on the unit price display Selection of the product grade for pricing lt gt Value increase Entry into the mode of totalizer reading fuel dispenser at rest Price setting for manual mode Unit price setting is done in the manual mode only namely as follows switching the calculator ON OFF directing the fuel dispenser display by the IR keyboard and depressing the key lt 0 gt selection of the figure for the price the value of which is to be changed by the key lt gt setting of the value of the selected figure by the key lt gt switching to another product grade dispensing hose by the key lt gt end of setting by depressing the key lt 0 gt Displaying of electronic totalizers Displaying of the electronic totalizer is carried out as follows the fuel dispenser is at rest all transactions are transferred to the POS and all nozzles are suspended in the boot by directing the IR keyboard onto the fuel dispenser display and by depressing the key lt gt the volume litre totalizer of the first nozzle will appear e g U0000012345 90 by depressing the key lt gt the sum totalizer of the first nozzle will appear e g A00000235678 9 by depressing the key lt gt volume and price total
28. n the LPG dispenser display One 7 digit totalizer showing the number of full litres pumped by the relevant hose cotresponds to each dispensing hose 3 3 5 Fuel Dispenser Display Back lighting Displays of all fuel dispensers ate back lighted by SMD LED diodes In case of the PDE calculator intensity of back lighting is controlled as follows the maximum intensity during dispensing and reduced to one third if the data on the display ate not changed automatic switching after expiration of 30 seconds 3 3 6 Signaling Diode SIG on the Display The signaling diode signaling the state of payment blocking and fault of the fuel dispenser red The signaling diode SIG is switched to continuous red light if the fuel dispenser waits for paying or is in the blocked state and is switched to the blinking red light if the fuel dispenser is faulty 3 3 7 Signaling Diode PWR on the Display The orange signaling diode PWR serves for signaling of dispenser calculator feeding If the diode is ON the dispenser calculator is actuated 19 USER MANUAL Bend 4 Maintenance and Service Prior to start any maintenance intervention into mechanical hydraulic or electric parts assemblies it is always necessaty to disconnect the fuel dispenser from the power supply source and to protect it from re connection reliably DO NOT OPEN THE JUNCTION BOX COVER IF THE FUEL DISPENSER IS ENERGIZED CAUTION Each handling and dismantling operation
29. of the parts and assemblies above even filter cover opening is conditioned by forcing the medium out of the fuel dispenser hydraulic system using nitrogen or inert gas Electric and electronic parts assemblies may be serviced only and exclusively by the specialist liable for safety of the device After completed intervention the conductors must be reinstated Correct conductor installation must prevent any contact with the moving parts of the winding module Caution After each service intervention tightness of hydraulic assemblies has to be inspected possible medium leaks have to be removed 4 1 Survey of main principles of LPG fuel dispenser maintenance e maintain all fuel dispenser assemblies clean so that possible unforeseeable fault can be identified easily and removed quickly e check condition of the nozzle and decide its repair or replacement depending on revealed defect e check door locks and nozzle accommodation boot for correct functioning e maintain the fuel dispenser clean pay attention particularly to cleanliness of calculator glass e lubricate the nozzle by silicone oil twice a week Maintenance of fuel dispenser body Parts of the fuel dispenser body lacquered or made of stainless steel need regular maintenance A great attention shall be paid to these parts particularly in winter season because aerosols of chloride preparations arisen from the salts used for road maintenance can result in
30. price of product 2 00 00 3 unit price of product 3 00 00 4 unit price of product 4 00 00 5 unit price of product 5 00 00 10 If the fuel dispenser calculator is connected to the control system then the price is updated after each calculator activation namely by the product values set in the control system 11 USER MANUAL ith DE LPG DISPENSERS SHARK 2 1 5 4 Current Time and Date code 04 The function enables to display and set the current date and time Setting can be done by depressing the key lt Enter gt and by loading date and time 17345 0 vii 2405 00 ie 04 DXX Parameter The first line displays time in the format HHMMSS hours minutes and seconds the second line displays date in the format DDMMYY day month and year example 17 34 50 24 05 00 2 1 5 5 Displaying of Program Version and Check Sum code 05 The function displays the number of the program version of the dispenser calculator and the check sum of memory parameters e Line 1 amount check sum e Line 2 litres version number e g 3 34 version 3 34 2 1 5 6 Displaying of Latest Error Conditions of Fuel Dispenser code 06 The function serves for displaying of the history of the latest ten error codes of faults occurred on the dispenser Table of error messages can be found in the Appendix D aux code item number description A 0 code of the last tenth error of the dispenser on
31. station is liable for its operation which shall be entrusted to the trained staff only having relevant authorization The operator refuels vehicle tanks by LPG professionally checks state of the fuel dispenser and the technology in the preset time intervals checks operation of the whole unit and maintains operating records The prohibit of smoking and open fire handing in the area of 10 m must be fixed on a visible places next to the fuel dispenser The notice of necessary motor switch off max volume of refueling 80 and braking the vehicle from undesirable motion has also be placed here From the design point of view the fuel dispensers and all components which might initiate explosion are approved by the state authorized institution the State Testing Laboratory No 210 FTZ Ostrava Radvanice which issues the necessary certificates Environmental safety is supported by I P Certificate No 90 00 895 01 TOM For detection of possible gas leaks relevant detectors sensors can be installed in the fuel dispenser area the sensors ate out of scope of the basic offer From the hygienic point of view the device is harmless for the operator and the owner When operating and maintaining the device it is advisable to protect the hands by gloves 18 FIRST AID Poisoning gaseous LPG When refueling avoid LPG vapor inhalation danger of suffocation The injured person must be taken out of the contaminated area Attention Fire and explosion
32. the service organization see Section 5 e El wiring must be carried out by the qualified staff e Assure that the operable fire extinguisher is available e When handling the device use suitable protective aids 0 2 Brief Characteristics of the Used Medium LPG is the trade name for liquefied mix of light hydrocarbons predominantly with three to four carbon atoms in the molecule LPG is obtained by synthetic petrol production and recently also by natural gas processing The liquefied LPG is a clear easily volatile liquid of specific odor By releasing overpressure the liquefied LPG is evaporated quickly and flammable gas roughly twice as heavy as air is generated By evaporation of liquefied LPG into air is generated explosive mix which is heavier than air and it is accumulated close to the earth Physical properties of liquid state propane butane formula C3Ha Gi molecular weight 44 09 58 12 boiling temperature C 42 6 0 6 density kg m at 20 C 502 579 Physical properties of gaseous state density kg m at atmospheric pressure 1 865 2 76 consistency air 1 1 562 2 091 LHV MJ m at 0 C and atmospheric pressure 93 57 123 76 Explosion limit when mixed with air in vol bottom 1 7 1 3 upper 10 9 9 3 ignition temperature in C 465 365 Table 1 Physical properties of main LPG mix components Gaseous LPG has moderately narcotic effect on the human organism
33. the setting modes are displayed on the dispenser display When controlling by the remote controller the data are displayed on the dispenser side which the setting mode was recalled from by the controller Individual parameters are displayed as follows 00003 2 svi 7890 13 ir 0 1 e L2 P r i ce Parameter number 01 Item number 2 Auxiliary code L Parameter value 327890 13 Auxiliary code Parameter number 2 1 4 Operator Mode The operator mode is started by pointing the dispenser display by the IR remote controller at the distance of ca 1 m from the dispenser and by depressing the key Shift and then the key lt REG gt All nozzles must be locked securely in the boot After the operator mode is recalled value of the first parameter is displayed Switching to the next parameters and their items is carried out using the keys lt Next gt and lt gt see sec 3 1 1 The operator mode enables to display but not change the following parameters po Description 04 06 History of failures o The operator mode is ended by depressing the key lt REG gt on the remote controller The mode is also ended automatically if no key is depressed for 60 seconds 2 1 5 Manager Mode The manager mode is started by pointing the dispenser display by the remote controller at the distance of ca 1 m from the dispenser and by depressing the key lt REG gt All nozzles must be locked securely
34. tion 9 is the oldest stored transaction The auxiliary code means the dispenser side A or B If the memory stack for the history of transactions is empty i e there is no transaction in the history error appears on the display 2 1 5 8 Access Password code 08 The function enables to display and change the access password into the manager mode Default setting is 1111 2 1 5 9 History of Maintenance code 09 The function enables to display codes of the last 10 service remote controllers which the calculator parameters wete set by 2 1 5 10 Operating Fuel Dispenser Mode code 12 The function defines the type of operating fuel dispenser mode parameter 3 alc Operating fuel dispenser mode 0 Automatic mode Manual with switching to the automatic mode default 1 2 Manual with switching to the automatic mode and locking 3 Manual stand alone mode 4 Credit internal credit Chipper 13 USER MANUAL 18 2 UW LPG DISPENSERS SHARK The parameter may obtain the values in the range from 0 to 4 the value 4 may be set for the credit version PDE only e If value of the parameter equals to 0 the fuel dispenser is operated in the pure automatic mode i e it is connected to the master computer console The fuel dispenser is controlled by the computer fully fuel dispenser release locking setting of fuel prices etc Interrupted communication between the computer and the fuel dispens
Download Pdf Manuals
Related Search