JLDWS 1208 Dishwasher Instruction manual
Contents
1. please contact our extended warranty Something Not Working administrators by telephoning When you contact your local repair agent you 0870 010 7887 will need to give the following details They will give you details of your local Service 1 Your name address and post code Force Centre 2 Your telephone number 3 Clear and concise details of fault 31 The purchase date found on your receipt The model and serial number of the appliance found on the rating plate So that you always have these numbers at hand we recommend that you make a note of them here Your dishwasher is covered by a 3 year parts and labour guarantee see separate details given at point of sale Please retain your purchase receipt safely for the service engineer to verify the purchase details 32 Spare parts An authorised service engineer should service this product and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local repair agent by telephoning 0870 010 7887 33 34 35 John Lewis Partnership 171 Victoria Street London SW1E 5NN www johniewis com 117971580 00 022008 Subject to change without notice2. use abrasive products scouring pads or solvent acetone trichloroethylene etc Internal cleaning Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend every 3 months you run the wash programme for heavy soiled dishes using detergent but without dishes Prolonged periods of non operation If you are not using the machine for a prolonged period of time you are advised to 1 Unplug the appliance and then turn off the water 2 Leave the door ajar to prevent the formation of any unpleasant smells 3 Leave the inside of the machine clean Frost precautions 1 Unplug it ae i Turn the water tap off Avoid placing the machine in a location where P the temperature is below 0 C If this is 3 Remove the water inlet and discharge unavoidable empty the machine close the hoses appliance door disconnect the water inlet 4 Pull the machine out together with the pipe and empty it hoses Avoid over tilting the machine during Moving the machine transportation If you have to move the machine moving house etc Something not working The dishwasher will not start or stops during operation Certain problems are due to the lack of simple maintenance or oversights which can be solved with the help of the indications Important If you call out an engineer to a fault listed below or to repair a fault caused by incorrect use or
3. This optical signal will remain illuminated for all the duration of the washing programme Setting and starting the programme with delay start 1 After having selected the washing programme press the delay start button until the number of hours for the delay start appear in the digital display The start of the selected washing programme can be delayed for between 1 and 19 hours Close the dishwasher door the countdown starts automatically The countdown will decrease with steps of 1 hour The opening of the door will interrupt the countdown Close the door the countdown will continue from the point at which it was interrupted Once the delay start has elapsed the programme will start automatically Cancelling a delay start or a washing programme in progress e Simultaneously press and hold the two programme buttons positioned over the word Cancel until all the programme button lights come on 21 Cancelling a delay start involves also the cancelling of the washing programme set In this case you have to set the washing programme again If a new washing programme is to be selected check that there is detergent in the detergent dispenser Warning Interrupt or cancel a washing programme in progress ONLY if it s absolutely necessary Attention Hot steam may escape when the door is opened Open the door carefully Interrupt a washing programme in progress Open the dishwasher door the programm
4. and make sure that they remain with the appliance if it is moved or sold so that everyone using it through its life will be properly informed on appliance use and safety If you are unsure of the meanings of these warnings contact the John Lewis Never use the dishwasher if the electrical supply cable and water hoses are damaged or if the control panel work top or plinth area are damaged such that the inside of the appliance is freely accessible Contact your local repair agent in order to avoid hazard All sides of the dishwasher must never be drilled to prevent damage to hydraulic and electric components branch from which you purchased the For electrical and water connection appliance carefully follow the instructions given in the specific paragraphs Installation e This appliance is heavy Care should be Child safety taken when moving it e This appliance is designed to be operated e Check your dishwasher for any transport by adults Do not allow children to use the damage Never connect a damaged dishwasher unsupervised machine If your dishwasher is damaged e Keep all packaging well away from children contact your supplier There is a risk of suffocation e Keep all detergents in a safe place out of children s reach e Keep children well away from the dishwasher when the door is open Correct use e This dishwasher is only intended for washing household utensils suitable for machine washing e Do not put any
5. container cap is not properly closed Rinse aid was not used The rinse aid dispenser is empty 25 The wash results are not satisfactory There are streaks milky spots or a Decrease rinse aid dosage bluish coating on glasses and dishes Water drops have dried onto e Increase rinse aid dosage glasses and dishes e The detergent may be the cause Contact the detergent manufacturer s consumer care line 26 Technical data Dimensions Width 60 cm Height 85 cm Depth 60 cm Electrical connection Voltage Overall power Fuse Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door Water supply pressure Minimum 0 05 MPa 0 5 bar Maximum 0 8 MPa 8 bar Capacity 12 place settings cE Installation Warning It is dangerous to alter the Fitting under a counter specifications or attempt to modify this product in any way This appliance is heavy Care should be taken when moving it Care must be taken to ensure that the appliance does not stand on the electrical supply cable Any electrical work required to install this appliance must be carried out by a qualified electrician or competent person Any plumbing work required to install this appliance must be carried out by a qualified plumber or competent person Kitchen worktop or sink By removing the machine s worktop you ca
6. deactivate the Multi tab function before the start of a washing programme Once the programme is running the Multi tab function can NO longer be changed If you want to cancel the Multi tab function you have to cancel the programme setting and then deactivate the Multi tab function In this case you have to set a washing programme and desired options again Activation deactivation of the Multi tab function Simultaneously press and hold the two buttons positioned over the word Multi tab until the Multi tab indicator light illuminates This means that the function is active To deactivate the function press the same buttons again until the Multi tab indicator light turns off i If the drying results are not satisfactory we suggest that you 1 Fill up the rinse aid dispenser with rinse aid 2 Activate the rinse aid dispenser 3 Set the rinse aid dosage to position 2 e The activation deactivation of the rinse aid dispenser is only possible with the Multi tab function active Activation deactivation of the rinse aid dispenser 1 Press the On Off button The dishwasher must be in setting mode Simultaneously press and hold function buttons B and C until the lights of function buttons A B and C start flashing Press function button B the lights of function buttons A and C go off while the light of function button B continues to flash The digital display shows the current setting i 0 d rinse aid di
7. disposal facilities AN When a unit is no longer being used e Pull the plug out of the socket e Cut off the cable and plug and dispose of them e Dispose of the door catch This prevents children from trapping themselves inside and endangering their lives The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local council your household waste disposal service or the shop where you purchased the product Contents For the user Important safety information Description of the appliance The control panel The digital display Function buttons A B C D and E Audible signals Washing programmes When the dishwasher is first installed The water softener Filling with dishwasher salt Filling with rinse aid Adjusting the rinse aid dosage Daily use Loading cutlery and dishes The lower basket The cutlery basket The upper basket Adjusting the height of the upper basket Use of detergent Multi tab function Activation d
8. installation a charge will be made even if the appliance is under guarantee described in the chart without calling out an engineer Switch off the appliance and carry out the following suggested corrective actions Fault code and malfunction Possible cause and solution IL appears in the digital display The water tap is blocked or furred with limescale e Intermittent audible signal Clean the water tap Point shaped optical signal is flashing The water tap is turned off The dishwasher does not fill with Turn the water tap on water The filter where present in the threaded hose fitting at the water inlet valve is blocked Clean the filter in the threaded hose e The water inlet hose has not been correctly laid or it is bent or squashed Check the water inlet hose connection e Zl appears in the digital display e The sink spigot is blocked e Intermittent audible signal Clean out the sink spigot e Point shaped optical signal is flashing The water drain hose has not been correctly laid or it is The dishwasher will not drain bent or squashed Check the water drain hose connection 24 Fault code and malfunction Possible cause and solution e JU appears in the digital display e Intermittent audible signal e Point shaped optical signal is flashing Anti flood device is activated Close the water tap and contact our extended warranty administrators refer to Repairs Af
9. JLDWS 1208 Dishwasher Instruction manual John Lewis A Important safety information It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant warnings These warnings have been provided in the interest of safety You MUST read them carefully before installing or using the appliance If you are unsure of the meanings of these warnings contact the John Lewis branch from which you purchased the appliance B In the interest of your safety and to e All packaging must be removed before use ensure the correct use before e Any electrical and plumbing work required installing and first using the appliance to install this appliance must be carried out read this user manual carefully by a qualified and competent person including its hints and warnings To e For safety reasons it is dangerous to alter avoid unnecessary mistakes and the specifications or attempt to modify this accidents it is important to ensure that product in any way all people using the appliance are thoroughly familiar with its operation and safety features Save these instructions
10. ance and cleaning For information on maintenance and cleaning your dishwasher see the specific chapter in this instruction manual Service e This product should be serviced by an authorized service engineer and only genuine spare parts should be used Ecological hints To save water and energy and help protect the environment we recommend that you follow these hints Ensure that the water softener is correctly adjusted e Do not prewash under running water e Select the wash programme to suit the nature and degree of the soiling on the dishes e Do not use more detergent dishwasher salt and rinse aid than is recommended in these operating instructions and by the manufacturer of the respective product Delay start When possible programme your dishwasher to run over night to enable for example the use of economical overnight electricity tariffs Automatic Wash Programme This machine is fitted with a turbidity sensor which intelligently adjusts the temperature and rinsing cycles during the wash programme depending on the degree of soiling on the dishes This helps to reduce energy and water consumption on lightly soiled loads Environmental information The packaging materials are environmentally friendly and can be recycled The plastic components are identified by markings e g gt PE lt gt PS lt etc Please dispose of the packaging materials in the appropriate container at the community waste
11. anufacturer Glazed patterns may fade if machine washed frequently Silver and aluminium parts have a tendency to discolour during washing Residues e g egg white egg yolk and mustard often cause discolouring and staining on silver Therefore always clean left overs from silver immediately if it is not to be washed straight after use The lower basket The lower basket is designed to take saucepans lids plates salad bowls cutlery etc Serving dishes and large lids should be arranged around the edge of the basket ensuring that the spray arms can turn freely Ne YANAN UN i a The rows of prongs in the lower basket can lie flat to allow you to load pots pans and bowls 15 The cutlery basket Warning Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Take care when loading or unloading sharp items such as knives Forks and spoons should be placed in the removable cutlery basket with the handles facing downwards and the knives with their handles facing upwards If the handles protrude from the bottom of the basket obstructing the lower spray arm load the cutlery with the handles facing upwards Mix spoons with other cutler
12. asket aay raised With upper basket 27 cm lowered To move to the higher position proceed as follows 1 Pull out the basket until it stops 2 Carefully lift both sides upwards until the mechanism is engaged and the basket is stable x OA Pri a To lower the basket to the original position proceed as follows 1 Pull out the basket until it stops 2 Carefully lift both sides upwards and then allow the mechanism to drop back down slowly keeping hold of it Never lift or lower the basket on one side only With the upper basket raised we recommend you adjust the cup racks in the lowest position 17 Warning After loading your machine always close the door as an open door can be a hazard Use of detergent i Only use detergents specifically designed for use in dishwashers Please observe the manufacturer s dosing and storage recommendations as stated on the detergent packaging wy Using no more than the correct amount of detergent contributes to 20 approximately 20 g of detergent reducing pollution 30 approximately 30 g of detergent 3 All programmes with prewash need an Fill with detergent additional detergent dose 5 10 g that 1 Open the lid must be placed in the prewash detergent chamber 2 This detergent will be used during the prewash phase When using det
13. connections Water inlet connection This appliance must be connected to a cold water supply For making the connection itself the coupling nut fitted to the machine s inlet hose is designed to screw onto a 3 4 gas thread spout or to a purpose made quick coupling tap such as the Press block The water pressure must be within the limits given in the Technical data Your local Water Authority will advise you on the average mains pressure in your area 28 The water inlet hose must not be kinked crushed or entangled when it is being connected The appliance features inlet and drain hoses which can be turned either to the left or the right to suit the installation by means of the locknut The locknut must be correctly fitted to avoid water leaks Attention NOT all models of dishwashers have inlet and drain hoses provided with a locknut If the appliance is connected to new pipes or pipes which have not been used for a long time you should run the water for a few minutes before connecting the inlet hose DO NOT use connection hoses which have previously been used on an old appliance This appliance has been fitted with safety features which will prevent the water used in the appliance from returning back into the drinking water system This appliance complies with the applicable plumbing regulations Water drain connection The end of the drain hose can be connected in the following ways 1 To the sink outlet s
14. d off 1 Open the door remove the lower basket 2 The dishwasher filter system comprises a coarse filter A a microfilter B and a flat filter Unlock the filter system using the handle on the microfilter 3 Turn the handle about 1 4 a turn anticlockwise and remove the filter system 22 4 Take hold of the coarse filter A by the handle with the hole and remove from the microfilter B 5 Clean all filters thoroughly under running water 6 Remove the flat filter from the base of the washing compartment and clean both faces thoroughly 7 Put the flat filter back in the base of the washing compartment and ensure that it fits perfectly 8 Place the coarse filter A in the microfilter B and press together 9 Put the filter combination in place and lock by turning the handle clockwise to the stop During this process ensure that the flat filter does not protrude above the base of the washing compartment NEVER use the dishwasher without filters Incorrect repositioning and fitting of the filters will produce poor washing results and will result in damage to the appliance NEVER try to remove the spray arms If residues of soil have clogged the holes in the spray arms remove the debris with a cocktail stick i External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never
15. e washed in the dishwasher e Before loading the dishes you should Remove all left over food and debris Soften remnants of burnt food in pans e When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Lay small objects in the cutlery basket e Plastic items and pans with non stick coatings have a tendency to retain water drops these items will not dry as well as porcelain and steel items e Light items plastic bowls etc must be loaded in the upper basket and arranged so they do not move For washing in the dishwasher the following cutlery and dishes are not suitable are of limited suitability e Cutlery with wooden horn china or mother of pearls handles Plastic items that are not heat resistant Older cutlery with glued parts that are not temperature resistant Bonded cutlery items or dishes e Pewter or copper items e Lead crystal glass e Steel items prone to rusting e Wooden platters Items made from synthetics fibres Only wash stoneware in the dishwasher if it is specially marked as being dishwasher safe by the m
16. e will stop Close the door the programme will start from the point at which it was interrupted End of the washing programme The dishwasher will automatically stop and an audible signal informs you of the end of the washing programme When the washing programme has ended the optical signal on the floor beneath the dishwasher door will turn off Open the dishwasher door The indicator light of the programme just ended remains illuminated Switch off the dishwasher by pressing the On Off button Leave the dishwasher door ajar and wait a few minutes before removing the dishes in this way they will be cooler and the drying will be improved i When the washing programme has finished it is recommended that the dishwasher is unplugged and the water tap turned off Unloading the dishwasher e Hot dishes are sensitive to knocks The e Water may appear on the sides and the dishes should therefore be allowed to cool door of the dishwasher as the stainless steel down before removing from the appliance will eventually become cooler than the e Empty the lower basket first and then the dishes upper one this will avoid water dripping from the upper basket onto the dishes in the lower one Maintenance and cleaning Cleaning the filters The filters must be checked and cleaned from time to time Dirty filters will degrade the washing result Warning Before cleaning the filters ensure that the machine is switche
17. eactivation of the rinse aid dispenser Select and start a washing programme Unloading the dishwasher Maintenance and cleaning Cleaning the filters External cleaning Internal cleaning Something not working 20 20 22 22 22 23 24 For the installer Technical data Installation Unpacking Fitting under a counter Levelling Water connections Water inlet connection Water drain connection Electrical connection Repairs After sales service Guide to use the instruction manual 27 27 27 27 28 28 28 29 31 The following symbols will be found in the text to guide you throughout the instructions Safety instructions i Hints and tips we Environmental information Description Oe w Soa Upper basket Water hardness dial Salt container Detergent dispenser Rinse aid dispenser of the appliance 6 A 8 9 10 Rating plate Filters Lower spray arm Upper spray arm Worktop 10 The control panel m Rinse aid On Off m Muki ab Dey 70 Intensive Automatic SO Econemy Quick wash Rinse hold mm Salt 2 Delay start Digital display Delay start button Programme selection buttons Indicator lights On Off button Function buttons Os OT we a Indicator lights In addition to the programme indicator lights that allow you to see which programme is r
18. er basket from the dishwasher 3 Turn the water hardness dial to position 1 or 2 see table above 4 Replace the lower basket 11 Setting electronically i The dishwasher is factory set at level 5 1 Press the On Off button The dishwasher must be in setting mode Simultaneously press and hold function buttons B and C until the lights of function buttons A B and C start flashing Press function button A the lights of function buttons B and C go off while the light of function button A continues to flash The digital display shows the current level and a sequence of intermittent audible signals can be heard Examples 5 L displayed 5 intermittent audible signals pause etc level 5 iQ L displayed 10 intermittent audible signals pause etc level 10 To change the level press function button A Each time the button is pressed the level changes For the selection of the new level see the chart Examples If the current level is 5 by pressing function button A once level 6 is selected if the current level is 10 by pressing function button A once level 1 is selected To memorize the operation switch off the dishwasher by pressing the On Off button Filling with dishwasher salt Warning Only use salt specifically designed for use in dishwashers All other types of salt not specifically designed for use in a dishwasher especially table salt will damage the water softene
19. er when Multi tab function is active Activation deactivation of the audible signals Setting mode Press the On Off button if ALL programme button lights come on the appliance is in setting mode Always remember that when performing the following operations e Selecting a washing programme e Setting the water softener e Activating deactivating the rinse aid dispenser e Activating deactivating the audible signals the appliance MUST be in setting mode Press the On Off button if a programme button light comes on the last performed or selected programme is still set In this case to return to setting mode the programme has to be cancelled To cancel a set programme or a programme in progress Simultaneously press and hold the two function buttons B and C until all the programme button lights come on The programme has been cancelled and the appliance is now in setting mode Audible signals Audible signals have been introduced to help indicate which operations the dishwasher is performing Setting of the water softener End of programme Intervention of an alarm due to malfunction Factory setting audible signals activated i 1 Press the On Off button The dishwasher must be in setting mode It is possible to deactivate the audible signals using the function buttons on the control panel 2 Simultaneously press and hold function buttons B and C until the lights of function bu
20. ergent tablets place the tablet in compartment 1 2 Fill the detergent dispenser 1 with detergent The marking indicates the dosing levels 18 Detergent tablets Detergent tablets from different manufacturers dissolve at different rates For this reason some detergent tablets do not attain their full cleaning power during short washing programmes Therefore please use long washing programmes when using detergent tablets to ensure the complete removal of detergent residuals Multi tab function This appliance is equipped with the Multi tab function that allows the use of combi detergent tablets These products are detergents with a combined cleaning rinsing and salt functions They can also contain other different agents depending on which kind of tablets you choose 3 in 1 4 in 1 5 in 1 etc Check whether these detergents are suitable for your water hardness See the manufacturers instructions Once this function is selected it will remain active for all following wash programmes With the selection of this function the inflow of rinse aid and salt from each respective supply container is automatically deactivated and also the indicator lights for salt and rinse aid are deactivated When using the Multi tab function the cycle durations may change If this is the case the running time for the programme is automatically updated on the digital display Activate
21. n install it under a close fitting sink unit or a pre existing top providing the dimensions of the recess correspond to those shown in the picture Unpacking Remove all packaging before positioning the machine e If possible position the machine next to a water tap and a drain Proceed as follows 27 Remove the machine s worktop by unscrewing the two rear retaining screws 1 pull the worktop from the back of the machine 2 and slide out the front slots lifting the worktop 3 Insert the machine after adjusting the levelling with the adjustable feet When inserting the machine ensure that the water inlet and drain hoses are not kinked or squashed During all operations that involve accessibility to internal components the dishwasher has to be unplugged Be sure that once the appliance has been installed it is easily accessible for the service engineer in the event that a repair is required If the dishwasher is later used as a free standing appliance the original worktop must be re mounted The plinth on free standing appliances is not adjustable Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on either side of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level Water
22. ntent of these minerals and e Set the water softener level salts the harder your water is Water e Pour 1 litre of water into the salt container hardness is measured in equivalent scales and then fill with dishwasher salt Clarke degrees French degrees TH and e Fill the rinse aid dispenser mmol l millimol per litre international unit for the hardness of water i If you want to use combi detergent The softener should be adjusted according to tablets such as 3in1 4in1 5in1 the hardness of the water in your area Your etc set the Multi tab function see local Water Authority can advise you on the Multi tab function hardness of the water in your area 10 Water hardness Adjusting the water hardness setting Use of salt Clarke TH mmol l manually electronically 64 88 91 125 9 1 12 5 2 level 10 yes 53 63 76 90 7 6 8 9 2 evel 9 yes 46 52 65 75 6 5 7 5 2 evel 8 yes 36 45 51 64 5 1 6 4 2 evel 7 yes 28 35 40 50 4 0 5 0 2 evel 6 yes 23 27 33 39 3 3 3 9 2 evel 5 yes 18 22 26 32 2 6 3 2 1 evel 4 yes 13 17 19 25 1 9 2 5 1 evel 3 yes 5 12 7 18 0 7 1 8 1 evel 2 yes lt 5 lt 7 lt 0 7 1 evel 1 no Setting the water softener The water softener must be set in two ways manually using the water hardness dial and electronically Setting manually The dishwasher is factory set at position 2 1 Open the dishwasher door 2 Remove the low
23. pigot securing it to the underside of the work surface This will prevent waste water from the sink running into the machine 2 To a stand pipe provided with venthole minimum internal diameter 4 cm The waste connection must be at a height of between 30 cm minimum and 100 cm maximum from the bottom of the dishwasher DY To The drain hose can face either to the right or left of the dishwasher Ensure the drain hose is not bent or squashed as this could prevent or slow down the discharge of water The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided When connecting the drain hose to an under sink trap spigot the entire plastic membrane A must be removed Failure to remove all the membrane will result in food particles building up over time eventually blocking the dishwasher drain hose spigot 30 Our appliances are supplied with a security device to protect against the return of dirty water back into the machine If the spigot of your sink has a no return valve incorporated this can prevent the co
24. pon if the appliance is fully or partially loaded and if the dishes are lightly or heavily soiled The temperature of the water is automatically adjusted between 45 C and 70 C 2 Test programme for test institute 3 Ideal for washing a partially loaded dishwasher This is the perfect daily programme made to meet the needs of a family of 4 persons who only wish to load breakfast and dinner crockery and cutlery Consumption values Programme Programme Energy Water consumption duration consumption in litres in minutes in kWh 70 Intensive 1 4 1 6 16 18 Automatic 1 1 1 7 12 23 50 Economy 1 0 1 1 12 13 Quick wash 0 9 9 Rinse hold 0 1 4 1 The consumption values are intended as a guide and depends on the pressure and the temperature of the water and also by the variations of the power supply and the amount of dishes 2 The digital display shows the programme duration 3 Test programme for test institutes When the dishwasher is first installed Before using your dishwasher for the first The water softener time The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply which would have a detrimental or adverse effect on the operation of the appliance Ensure that the electrical and water connections comply with the installation instructions e Remove all packaging from inside the appliance The higher the co
25. r Only fill with salt just before starting one of the complete washing programmes This will prevent any grains of salt or salty water which may have been spilt remaining on the bottom of the machine for any period of time which may cause corrosion To fill 1 Open the door remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise Pour 1 litre of water into the container this is necessary only before filling with salt for the first time 3 Using the funnel provided pour in the salt until the container is full 4 Replace the cap making sure that there is G no trace of salt on the screw thread or on the gasket 5 Replace the cap tightly turning it clockwise until it stops with a click Do not worry if water overflows from the unit when filling with salt this is quite normal The salt indicator light on the control panel can remain on for 2 6 hours after the salt has been replenished assuming the dishwasher remains switched on If you are using salt that takes longer to dissolve then this can take longer The operation of the machine is not affected Filling with rinse aid 12 Warning Only use branded rinse aid for dishwashers Never fill the rinse aid dispenser with any other substances e g dishwasher cleaning agent liquid detergent This would damage the appliance Rinse aid ensures thorough rinsing and spot and streak free dr
26. rrect draining of your dishwasher We therefore advise you to remove it When connecting the drain hose to an under sink trap spigot the entire plastic membrane A must be removed Failure to remove all the membrane will result in food particles building up over time eventually blocking the dishwasher drain hose spigot Electrical connection Warning Safety standards require the appliance to be earthed Prior to using the appliance for the first time ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed The fuse rating is also to be found on the rating plate Always plug the mains plug into a correctly installed shockproof socket Multi way plugs connectors and extension cables must not be used This could constitute a fire hazard through overheating If necessary have the domestic wiring system socket replaced In case that the electrical cable has to be replaced contact your local repair agent The plug must be accessible after the appliance has been installed Never unplug the appliance by pulling on the cable Always pull the plug The manufacturer accepts no liability for failure to observe the above safety precautions Repairs After sales service Ifthe unlikely event of your appliance requiring Before calling out an engineer please ensure service or if you wish to purchase spare parts you have read the details under the heading
27. solvents in the dishwasher This could cause an explosion e Knives and other items with sharp points must be loaded in the cutlery basket with their points down or placed in a horizontal position in the upper basket e Only use products detergent salt and rinse aid suitable for dishwashers e Avoid opening the door whilst the appliance is in operation hot steam may escape Do not take any dishes out of the dishwasher before the end of the washing cycle e After use isolate the appliance from the power supply and turn off the water supply e This product should be serviced only by an authorized service engineer and only genuine spare parts should be used e Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons could cause injury or serious malfunctioning Contact your local repair agent Always insist on genuine spare parts General safety e Dishwasher detergents can cause chemical burns to eyes mouth and throat Could endanger life Comply with the safety instructions of the dishwasher detergent manufacturer e The water in your dishwasher is not for drinking Detergent residues may still be present in your machine e Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves Do not sit or stand on the open door Mainten
28. spenser deactivated i d rinse aid dispenser activated To change the setting press function button B again the digital display shows the new setting To memorize the operation switch off the dishwasher by pressing the On off button If you decide to revert back to the use of individual detergents we advise that you 1 Deactivate the Multi tab function 2 Fill up the salt container and the rinse aid dispenser again 3 Adjust the water hardness setting to the highest setting and perform 1 normal washing programme without loading any dishes 4 Adjust the water hardness setting according to the hardness of the water in your area 5 Adjust the rinse aid dosage Select and start a washing programme Select the washing programme and delay start with the door slightly opened The start of the programme or the countdown of the delay start will occur only after the closure of the door Until then it is possible to modify the settings 20 Check that the baskets have been loaded correctly and that the spray arms are free to rotate Check that the water tap is opened Press the On Off button The dishwasher must be in setting mode Press the button corresponding to the required programme see Washing programmes chart Close the dishwasher door the programme starts automatically Once the washing programme has started a point shaped optical signal appears on the floor beneath the dishwasher door
29. ter Sales Service on the following pages Malfunction Possible cause and solution The programme does not start The dishwasher door has not been properly closed Close the door The main plug is not plugged in Insert the main plug The fuse has blown out in the household fuse box Replace the fuse Delay start has been set If dishes are to be washed immediately cancel the delay start Once these checks have been carried out warranty administrators refer to section switch on the appliance Repairs After Sales Service The programme will continue from the point at which it was interrupted If the malfunction fault code reappears or if other fault codes not described in the charts appear please contact our extended The wash results are not satisfactory The dishes are not clean The dishes are wet and dull The wrong programme has been selected The dishes are arranged in such a way as to stop water reaching all parts of the surface The baskets must not be overloaded The spray arms do not rotate freely due to incorrect arrangement of the load The filters in the base of the washing compartment are dirty or incorrectly positioned Too little or no detergent has been used Where there are limescales deposits on the dishes the salt container is empty or the incorrect level of the water softener has been set The drain hose connection is not correct The salt
30. ttons A B and C start flashing 3 Press function button C the lights of function buttons A and B go off while the light of function button C continues to flash The digital display shows the current setting lib Audible signals activated To change the setting press again function button C Each time the button is pressed the level changes the digital display shows the new setting Ob Audible signals deactivated 5 To memorize the operation switch off the dishwasher by pressing the On Off button Washing programmes Programme Degree of soil Type of load Programme description Prewash Crockery Main wash 70 Intensive Heavy soil cutlery pots and 1 intermediate rinse pans Final rinse Drying Prewash Crockery Main wash Automatic 1 Any cutlery pots and 1 or 2 intermediate rinses pans Final rinse Drying Prewash Crockery and Main wash 50 Economy 2 Normal soil 1 intermediate rinse cutlery ne Final rinse Drying Quick wash 3 Normal light soil Crockery and Main wash cutlery Final rinse Rinse hold Any Partial load to be completed later in the day 1 cold rinse to avoid food scraps from sticking This programme does not require the use of detergent 1 During the Automatic washing programme the level of soiling on the dishes is determined by how cloudy the water is The programme duration water and energy consumption levels can vary this depends u
31. unning or has been selected other indicator lights will help you in the use and maintenance of your dishwasher Indicator lights Comes on when the special salt has run out Salt 1 Comes on when the rinse aid has run out Rinse aid 1 70 Intensive Automatic 50 Economy Quick wash Rinse hold mm Salt E g Rinse aid me Multi tab Indicator lights Multi tab Indicates the activation deactivation of the Multi tab function See Multi tab function 1 The salt and rinse aid indicator lights are never on while a washing programme is running even if filling with salt and or rinse aid is necessary The digital display i The digital display indicates The level of hardness to which the water softener is set The approximate remaining time of the running programme Activation deactivation of the rinse aid dispenser ONLY with Multi tab function active The end of a washing programme the digital display shows zero The countdown of the delay start Fault codes concerning malfunction of the dishwasher Activation deactivation of the audible signals Function buttons A B C D and E The following functions can be set using these buttons e Setting the water softener level e Cancelling a washing programme or a delay start in progress Activation deactivation of the Multi tab function Activation deactivation of the rinse aid dispens
32. y to prevent them from sticking together For best results we recommend you use the cutlery grids If the size and dimensions of the cutlery do not allow the use of the grids they can be easily hidden or removed The upper basket The upper basket is designed for saucers salad bowls cups glasses pots and lids Arrange items on and underneath the cup racks so that water can reach all surfaces Glasses with long stems can be placed upside down in the cup racks The cup racks can be adjusted in three different positions to improve loading flexibility 16 For glasses with long stems according to the size and dimensions set the glass holder to the left or right position The central rows of prongs can be easily lowered to improve loading flexibility Before closing the door ensure that the spray arms can rotate freely Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position Maximum height of the dishes in the lower basket With upper b
33. ying Rinse aid is automatically added during the last rinse i 1 Open the container by pressing the release button A 2 Add the rinse aid in the container The maximum level for filling is indicated by 13 The dispenser holds about 110 ml of rinse aid which is sufficient for between 16 and 40 dishwashing cycles depending upon the dosage setting Ensure that the lid is closed after every refill Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Adjusting the rinse aid dosage According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector position 1 minimum dosage position 6 maximum dosage The dose is factory set in position 4 Increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades Daily use e Check if it s necessary to refill with dishwasher salt or rinse aid e Open the door and slide out the baskets to load the dishes e Load cutlery and dishes into the dishwasher e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme Loading cutlery and dishes Sponges household cloths and any object that can absorb water may not b
Download Pdf Manuals
Related Search