SK18A User`s Manual
Contents
1. For the usage of UICOOA please refer to UICOOA User s Manual RB7 and RB6 have been connected to UICOOA connector both these pins are used for ICSP User is advice not to use these pin as input Even when using as output RB7 or RB6 pin are recommended to be used in controlling non critical device such as LED LCD 7 segments or buzzer It is recommended to isolated ICSP signals from application circuit by using series resistor range 220 ohm and above Please refer to UICOOA User s Manual for further details Hence in SK18A RB7 and RB6 were designed as active High LED output Created by Cytron Technologies Sdn Bhd All Rights Reserved 7 Cytron 5 ROBOT HEAD to TOE Technologie Product User s Manual SK18A 6 GETTING STARTED SKI18A is ready to be plug and use no extra driver or software is necessary It is a hardware platform for the use of UICOOA please install the necessary driver or configure the correct setting in window SK18A is ready be used to start the electronics interface The I O of the microcontroller can be accessed through few methods 1 I O port to electronic components e Connect the components that are needed onto the I O port Connect the electronic device to PIC MCU I O port through Header pin Extend the I O port to development area using jumper wire User may also solder the necessary interface to PCB like ordinary donut board 2 I O port to multi meter e Put the multi meter probe on2. for PIC MCU Created by Cytron Technologies Sdn Bhd All Rights Reserved 5 Cytr on gt ROBOT HEAD to TOE Technologie Product User s Manual SK18A 4 PRODUCT SPECIFICATION SK18A is designed to offer starting up platform for development the specification of PIC MCU used should be referred Absolute Maximum Rating Symbol Parameter Min Max Unit Operating voltage Battery or DC adaptor can be used Note Only 1 power supply should be provided to SKI8A Created by Cytron Technologies Sdn Bhd All Rights Reserved 6 Cytr on 5 ROBOT HEAD to TOE Technologie Product User s Manual SK78A 5 INSTALLATION HARDWARE SK18A come with UICOOA ICSP USB programmer connector to offer simple way for downloading program From user feedback and experience using UICOOA ICSP programmer is very easy and save plenty of development time 5 1 Loading Program Using UICO0A Programmer Connect SK18A as shown in following figure bo O O 00000003 Sa T ar Py C LET U LED2 Gnd RB5 RB4 RB5 RAI RA2 RAS RA4 RBS RB2 RB1 RBO 5V 12V From UICOOA eae agaaeaunnae 1 ay r a t a e a a a a 3 d 5 s r SK18A should be powered either from battery or DC adaptor Plug 18 pins PIC16F microcontroller please ensure the first pin of microcontroller is plugged correctly Power up SK18A by turning the slide switch to ON Now the hex code is ready to be loaded to SK18A
3. Cytron Technologie SKISA 18 Pins PIC START UP KIT cal LHiAr AAP haoAo k z Ee DO 3 3 Ls Te 8 ee CYTRON SKIBA i tn User s Manual V1 1 Dec 2007 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates It is your responsibility to ensure that your application meets with your specifications No representation or warranty is given and no liability is assumed by Cytron Technologies Incorporated with respect to the accuracy or use of such information or infringement of patents or other intellectual property rights arising from such use or otherwise Use of Cytron Technologies s products as critical components in life support systems is not authorized except with express written approval by Cytron Technologies No licenses are conveyed implicitly or otherwise under any intellectual property rights T a ee ee a Cytron 5 Technologie Index Introduction and Overview Packing List Board Layout Product Specification Installation hardware 5 1 Loading Program Using UICOOA Programmer Getting Started Warranty Appendix A schematic Created by Cytron Technologies Sdn Bhd All Rights Reserved ROBOT HEAD to TOE Product User s Manual SK78A So Oo NN N A A W N p lt Cytr on gt ROBOT HEAD to TOE Technologie Product User s Manual SK18A 1 INTROD
4. UCTION AND OVERVIEW SK18A is designed to offer an easy to start board for PIC MCU user However all interface and program should be developed by user This board comes with basic element for user to begin project development It offers plug and use features This kit is designed to offer e Nice outlook e Industrial grade PCB e Every board is being tested before shipped to customer e Compact powerful flexible and robust start up platform e Suitable for hobbyists and experts e Save development and soldering time e No extra components required for the PIC to function e 11 T O pins are nicely labeled to avoid miss connection by users e Connector for UICOOA low cost USB ICSP PIC Programmer offer simple and fast method to load program e No more frustrated work plugging PIC out and back for re programming e Perfectly fit for 18 pins PIC16F MCU e With UICOOA program can be loaded in less than 4 seconds e Dimension 13 3cm x 6 9cm SKI8A come with e 5V voltage regulator 1A max e 20MHz oscillator e Reset button e x programmable push button e 2x programmable LED e Box header for UICOOA e On Off switch for main power e DC adaptor socket as power input e And all the necessities to eliminate users difficulty in using PIC Users are able to utilize the function of PIC by directly plugging in the I O connectors in whatever way that is convenient to user With UICOOA connector on board user can start developing projects a
5. nd have fun with this kit right away This kit comes WITHOUT PIC microcontroller to give the freedom for user to choose PIC type This document explains the method to use SK18A Created by Cytron Technologies Sdn Bhd All Rights Reserved 2 C Ver on 5 ROBOT HEAD to TOE pe tee oct ser s Manual oni 2 PACKING LIST Please check the parts and components according to the packing list If there are any parts missing please contact us at sales cytron com my immediately 1 x SK18A board with all components shown soldered PIC MCU Not included please purchase separately from Cytron website UICOOA Not included please purchase separately from Cytron website User Manual Not included please download from Cytron website a Created by Cytron Technologies Sdn Bhd All Rights Reserved 3 Cytron 5 ROBOT HEAD to TOE Technologies Product User s Manual SK78A 3 BOARD LAYOUT A O K 3 J O lo 3 3 lt g Pin 1 of PIC OAS DC power adaptor socket L 18 pin IC socket for PIC MCU B Banery connector _ Battery connector H_ Header pin and turn pin Box Header for UICOOA Power indicator LED Programmer D__ Output LEDs from PIC MCU J Reset button lt Slide switch for main power supply SV regulator Ld A is a DC power adaptor socket for user to plug in DC adaptor The input voltage should be ranged from 7 to 15V B is a 2510 2 way connector for battery i
6. nput The battery voltage should be between 7 to 15V Please ensure the polarity of voltage is correctly plugged before power up SKI8A The and is have been labeled at the side of connector C is a 2x5 box header for UICOOA USB ICSP PIC Programmer D consist of 2 LEDs connected to RB6 and RB7 as active High output for PIC MCU These LEDs are controllable from PIC MCU E is a slide switch to On Off the power supply from DC adaptor or Battery connector Pushing the switch down will ON SKI8A F is a 5V voltage regulator 1A maximum G 18 pin IC socket for user to plug in any 18 pin PIC16F MCU 8 bit Of course the IC package should be PDIP Please ensure the first pin is at the top side Created by Cytron Technologies Sdn Bhd All Rights Reserved 4 Cytr on gt ROBOT HEAD to TOE Technologie Product User s Manual SK18A H Consist of 14 lines of header pin and turn pin It is fully compatible between SKI8A Turn pin offer simple way to check voltage with multi meter probe 14 pins of PIC MCU are extended out to these pin except OSC connected to crystal RB6 and RB7 connected to LEDs and UICOOA box Header I is on board 5V indicator LED It will light ON as long as the input power is correctly connected and the slide switch is ON J is a push button with the function of Reset for PIC MCU K is a development area for user to solder electronic components as input or output
7. the turn pin to check the voltage Created by Cytron Technologies Sdn Bhd All Rights Reserved 8 Cytr on gt ROBOT HEAD to TOE Technologie Product User s Manual SK18A 7 WARRANTY gt Product warranty is valid for 6 months gt Warranty only applies to manufacturing defect gt Damage caused by miss use is not covered under warranty gt Warranty does not cover freight cost for both ways Prepared by Cytron Technologies Sdn Bhd 19 Jalan Kebudayaan IA Taman Universiti 81300 Skudai Johor Malaysia Tel 607 521 3178 Fax 607 521 1861 URL www cytron com my Email support cytron com my sales cytron com my Created by Cytron Technologies Sdn Bhd All Rights Reserved 9 Cytron Technologie Appendix A Adaptor Socket1 PYR2 5 T Vin i Power Connector 7 3 j 1 Slide Switch 2310 02 VPP Header 3X2 PICIOFS4A ROBOT HEAD to TOE Product User s Manual SK18A D1 7805 U1 1 3 on 5V IN4007 Cl Rl LQuF25V 330 POWER OSC2 CLKOUT Vdd RB RB4 MCLR JP Header 14 Created by Cytron Technologies Sdn Bhd All Rights Reserved 10
Download Pdf Manuals
Related Search