Clean Me & Check Me - LINAK Actuator
Contents
1. IPX6 X Wash with a brush and water The water can be under pressure but the system must not be hosed down directly with a high pressure cleaner Max 20 C IPX6 Washable Clean by the use of water tunnels X can have a value of between 1 and 6 The following products can be marked with IP x6 but they are still allowed for wash tunnels ACP ACM mini ACM new BA18 CB12 14 DJB FS2 HB40 LA28 LA32 LA34 stand LA34 comp The materials are resistant to the majority of cleaners and disinfectants used in the hospital and nursing home sector Cleaning with a steam cleaner for example is not permitted as it will not be possible to maintain a minimum distance of 300 mm from the electrical parts IP66 Washable products can be washed in wash tunnels that washes according to the Maschinelle Dekontamination provided that the following guidelines are complied with e The cleaning and disinfection cycle in the wash tunnel must not last longer than 10 minutes e The nozzle pressure in the wash tunnel must not exceed 10 bar e The distance between the nozzle and the electrical parts must be at least 300 mm e The handset and motor plug must be pushed right in e The water temperature must not exceed 65 C e Cooling with cold water is not permitted To avoid degreasing of the piston rod the actuator should be retracted to minimum stroke before washing The following directions regarding cleaners and disinfectants2. LUXEMBOURG LINAK Actuator Systems NV SA Phone 32 0 92 30 01 09 Fax 32 0 92 30 88 80 E mail info linak be www linak be BRAZIL LINAK Do Brasil Com rcio De Atuadores Ltda Phone 55 11 28 32 70 70 Fax 55 11 28 32 70 60 E mail info linak com br www linak com br CANADA LINAK Canada Inc Phone 1 50 22 53 55 95 Fax 1 4162 55 77 20 E mail info linak ca www linak us com CZECH REPUBLIC LINAK C amp S S R O Phone 420 58 17 41 814 Fax 420 58 17 02 452 E mail ponizil linak cz www linak cz DISTRIBUTORS ARGENTINA Novotec Argentina SRL Phone 54 11 4303 8900 89 Fax 54 11 4032 0184 E mail info novotecargentina com www novotecargentina com AUSTRALIA Ballarat Industrial Supplies www ballind com au BL Shipways amp Co www blshipway com au Gas Strut Marine and Industrial www gasstrutmarine com au Prime Motion amp Control www primehyd com au West Vic Industrial Supplies www westvicindustrial com au COLOMBIA MEM Ltda Phone 57 1 334 7666 Fax 57 1 282 1684 E mail servicioalcliente memltda com co www memltda com co INDONESIA Pt Himalaya Everest Jaya Phone 62 21 54 48 956 65 Fax 62 21 61 94 658 1925 E mail hejplastic div centrin net id www hej co id IRAN Bod Inc Phone 98 21 88 99 86 35 6 Fax 98 21 88 95 44 81 E mail info bod ir www bod ir DENMARK LINAK A S Group Headquarters Guderup Phone 45 73 15 15 15 Fax 45 74 45
3. 80 48 Fax Sales 45 73 15 16 13 E mail info linak com www linak com DENMARK LINAK Danmark A S Phone 45 86 80 36 11 Fax 45 86 82 90 51 E mail linak linak silkeborg dk www linak dk FINLAND LINAK OY Phone 358 10 84 18 700 Fax 358 10 84 18 729 E mail linak linak fi www linak fi FRANCE LINAK France E U R L Phone 33 0 2 41 36 34 34 Fax 33 0 2 41 36 35 00 E mail linak linak fr www linak fr GERMANY LINAK GmbH Phone 49 60 43 96 55 0 Fax 49 60 43 96 55 60 E mail info linak de www linak de INDIA LINAK A S India Liaison Office Phone 91 12 04 39 33 35 Fax 91 12 04 27 37 08 E mail info linak in www linak in IRELAND LINAK UK Limited Ireland Phone 44 0 121 544 2211 Fax 44 0 121 544 2552 E mail sales linak co uk www linak co uk MEXICO ILSA S A de C V Phone 52 55 53 88 39 60 Fax 52 55 53 88 39 66 E mail linak ilsamexico com www ilsamexico com PERU Percy Martin Del Aguila Ubillus Phone 51 99 88 39 879 RUSSIAN FEDERATION 000 FAM Phone 7 81 23 31 93 33 Fax 7 81 23 27 1454 E mail purchase fam drive ru www fam drive ru SINGAPORE Servo Dynamics Pte Ltd Phone 65 68 44 02 88 Fax 65 68 44 00 70 E mail servodynamics servo com sg www servo com sg SOUTH AFRICA Industrial Specialised Applications CC Phone 27 1131 22 292 or 27 11 20 77 600 Fax 27 1131 56 999 E mail gartht isagroup co za www isaza co za UNI
4. CleanMe Check Me functional for 12 years software timer controlled from production date The 12 years is based on the Clean Me Check Me being used 80 on battery supply and 20 with mains supply The lifetime can change according to the way that the Clean Me Check Me is being used LINAK TS ee lt 80 C 176 F WE IMPROVE YOUR LIFE Item CME90001 0 Li ion Date 2009 05 05 IPX5 Washable 0 7654321 NOT TO BE OPENED BY UNAUTHORIZED PERSONNEL MADE BY LINAK A S DENMARK XS CULL E P 0 123456 0001 M576 Page 20 of 24 DRAWING APPENDIX Clean Me Check Me w lt L a Lu gt Page 21 of 24 DECLARATION OF CONFORMITY LINAK A S Smedeveenget 8 DK 6430 Nordborg hereby declares that LINAK Actuator System Accessory CME CleanMe CheckMe CleanMe CheckMe And Control Box CB6S and or Control Box CB16 and or Control Box CB20 complies with the EMC Directive 2004 108 EC according to following standards EN 61000 4 2 1995 A1 A2 EN 61000 4 3 2006 EN 61000 4 4 2004 EN 61000 4 5 1995 A1 EN 61000 4 6 1996 A1 EN 55011 1998 A1 A2 Class B and complies with Low Voltage Directive 2006 95 EC according to the standard EN 60601 1 1990 Medical electrical equipment cl 20 3 Dielectric strength 500 V DC Date 2009 06 11 Signature Dofar MEP 7 John Kling Page 22 of 24 LINAK APPLICATION POLICY The purpose of the application policy is to define areas of r
5. FEDERATION 000 LINAK Phone 7 49 52 80 14 26 Fax 7 49 56 87 14 26 E mail info linak ru www linak ru SOUTH KOREA LINAK Korea Ltd Phone 82 0 2 6231 1515 Fax 82 0 2 6231 1516 E mail scully linak kr www linak kr SPAIN LINAK Actuadores S L u Phone 34 93 58 82 777 Fax 34 93 58 82 785 E mail linakact linak es www linak es SWEDEN LINAK Scandinavia AB Phone 46 87 32 20 00 Fax 46 87 32 20 50 E mail info linak se www linak se SWITZERLAND LINAK AG Phone 41 43 38 83 188 Fax 41 43 38 83 187 E mail info linak ch www linak ch Terms of use TAIWAN LINAK A S Taiwan Representative Office Phone 886 22 72 90 068 Fax 886 98 92 92 100 E mail michael chen linak com tw www linak com tw TURKEY LINAK Turkey Representative Office Phone 90 31 24 72 63 38 Fax 90 31 24 72 66 35 E mail irul linak com tr www linak com tr UNITED KINGDOM LINAK UK Limited Phone 44 0 121 544 2211 Fax 44 0 121 544 2552 E mail sales linak co uk www linak co uk The user is responsible for determining the suitability of LINAK products for specific application LINAK takes great care in providing accurate and up to date information on its products However due to continuous development in order to improve its products LINAK products are subject to frequent modifications and changes without prior notice Therefore LINAK cannot guarantee the correct and actual status of said information on its
6. products While LINAK uses its best efforts to fulfil orders LINAK cannot for the same reasons as mentioned above guarantee the availability of any particular product Therefore LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK All sales are subject to the Standard Terms of Sale and Delivery for LINAK For a copy hereof please contact LINAK LINAK A S reserve the right to make technical alterations Copyright LINAK 2010 10 MA M9 02 335 B LINAK amp WE IMPROVE YOUR LIFE
7. 1 5 11 External radiation Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility The relevant technical documentation is compiled in accordance with part B of Annex VII and that this documentation or part hereof will be transmitted by post or electronically to a reasoned request by the national authorities This partly completed machinery must not be put into service until the final machinery into which it is to be incorporated has been declared in conformity with the provisions of this Directive where appropriate Date 2010 01 01 Signature Dolina Pi John Kling Certification and Regulatory Affairs Page 8 of 24 Misc on the Clean Me Check Me system Warranty and service life The LINAK warranty covers manufacturing defects in the products starting from the date of manufacture There is 18 months for MEDLINE and CARELINE products The warranty is limited to the value of the LINAK product LINAK s guarantee is only valid so far as the products have been used and maintained correctly and has not been tampered with Furthermore the products must not be exposed to violent treatment In the event of this the warranty will be ineffective invalid LINAK s warranty is only valid if the system is unopened and has been used correctly All LINAK products are designed to have an optimum service life as a matter of course but the expected service life in a specific appl
8. MEDLINE CARELINE IMPROVING EFFICIENCY IMPROVING EFFICIENCY Clean Me Check Me LINARK 3 WWW LINAK COM WE IMPROVE YOUR LIFE Page 1 of 24 To learn more about LINAK please visit Page 2 of 24 Contents A EE E ded caus E E EE E E E 4 Important o A A nnan cee ee ane nanne nnne 5 Safety MISTI UICTONNS eenaa e A E Ee aaa aaar aee aaa 5 Before installation reinstallation or troubleshooting ooooconnococcccccncnccccnnanoncnnnccnoncnononannnannncnnnnncncrncnnnnnnnrs 6 A eraoo e eA a Aaa a aE a TEO aaae a aeaaaee aa aa a a 6 D ring Operations a aa aa dea aaa iaa Aae da aaa AE a Oaea aa EEA 6 RED GINS ose E A E E EE E E sios 7 Manufacturer s declara A Rs 8 Misc on the LINAK Clean Me Check Me system Warranty and AAA cutie e a a aere ada Daaa E Ee aaa E aaea da aa aaa 9 MIA os 9 IP Protection degree ccir e e iaa iianmen ee a a aa aaa aae aAa a a a a 10 Environmental conditions ii aaRiciaaa 11 Keys to SYIMDOIS aaa 12 Description of the LINAK Clean Me amp Check Me system How to connect Clean Me amp Check Me oooccocococccoccccccccccononanonnncnnnncnnnonnnnnn nn nc nnnnnnncrrrnnnnnnnnnnrncnnrrrrnnnnnnnnnncnnns 14 Functionality of the user interface idad 15 Reset procedure of Clean Me Check Me ccccccccccceeeceeeceeeeeeeeeeeeeeeseeeeseseeeeeeeseeeseeessseeeeseeeesseesseeeseeeeeanens 16 User interface confirguration Clean Me oooooooonocicccnnccnnonnnnnnnonnnnnnnnnnnnnnnnnnnnnnn corno nnnrnrnnnnnnnn nn n
9. TED ARAB EMIRATES Mechatronics Phone 971 4 26 74 311 Fax 971 4 26 74 312 E mail mechtron emirates net ae www mechatronics ae SLOVAKIA LINAK Slovakia s r o Phone 421 51 75 63 414 Fax 421 51 75 63 410 E mail pOlinak sk www linak com ITALY LINAK Italia S r l Phone 39 02 48 46 33 66 Fax 39 02 48 46 82 52 E mail info linak it www linak it JAPAN LINAK K K Phone 81 45 53 30 802 Fax 81 45 53 30 803 E mail linak linak jp www linak jp MALAYSIA LINAK Actuators Sdn Bhd Phone 60 42 10 65 00 Fax 60 42 26 89 01 E mail info linak asia com www linak my NETHERLANDS LINAK Actuator Systems B V Phone 31 76 5 42 44 40 Fax 31 76542 61 10 E mail info linak nl www linak nl NEW ZEALAND LINAK New Zealand Ltd Phone 64 95 80 20 71 Fax 64 95 80 20 72 E mail nzsales linak com au www linak co nz NORWAY LINAK Norge AS Phone 47 32 82 90 90 Fax 47 32 82 90 98 E mail info linak no www linak no For contact details on other countries please visit www linak com or contact LINAK INTERNATIONAL Phone 45 73 15 15 15 Fax 45 74 45 90 10 E mail info linak com www linak com Page 24 of 24 USA LINAK U S Inc North and South American Headquarters Phone 1 50 22 53 55 95 Fax 150 22 53 55 96 E mail info linak us com www linak us com POLAND LINAK Polska Phone 48 22 500 28 74 Fax 48 22 500 28 75 E mail dkreh linak dk www linak pl RUSSIAN
10. aba A a O m E Page 13 of 24 UL file number UL file number UL file number CSA PSE Mark Product with a thermofuse For indoor use House Safety isolating transformer Electronics scrap Equipment KI 2 Double square Patient part of type B Mand Patient part of type BF Earth protection Equipment class1 Earth CE Mark C TICK Discription of the LINAK Clean Me 8 Check Me system How to connect Clean Me amp Check Me OpenBus CB CB20 Clean Me amp Check Me Handset Alternatively OpenBus CB CB20 Clean Me amp Check Me Handset Page 14 of 24 Functionality of the user interface Clean Me and Check Me are single user interfaces that can also be combined into one When a diode is alight it indicates the time or number of washes to the next cleaning or service e g if the Clean Me is set to be cleaned every 14 days the diode will start at the first green diode on the left and every second day 8 diodes from start until time of cleaning move towards the yellow diode 8 indicating that it is time to clean the bed These interval settings can be adjusted both for Clean Me and Check Me CheckMe Start Service o o o gt Start Wash CleanMe The diodes will only be alight as long as the application is connected to the mains The battery backup will supply the necessary power to keep the Clean Me Check Me functional counting just not visible
11. ch is authorized to repair LINAK products Changes in installation and use of LINAK systems can affect their operation and durability The products are not to be opened by unauthorized person nel The User Manual has been written on the basis of our present technical knowledge We are constantly working on updating the information and we therefore reserve the right to carry out technical modifications LINAK A S Page 4 of 24 Important information Description of the various signs used in this manual Warning Failure to comply with these instructions may result in accidents involving serious personal injury pal Failing to follow these instructions can result in the product being damaged or destroyed Safety instructions Safe use of the system is possible only when the operating instructions are read completely and the instructions contained are strictly observed Failure to comply with instructions marked with the NOTE symbol may result in serious damage to the system or one of its components Persons who do not have the necessary experience or knowledge of the product products must not use the product products Besides persons with reduced physical or mental abilities must not use the product products unless they are under surveillance or they have been thoroughly instructed in the use of the apparatus by a person who is responsible for the safety of these persons Moreover children must be under surveillance to ensur
12. diodes not lit If the OpenBus control box that the Clean Me Check Me is connected to has a battery then you will be able to activate the diodes for a short period of time when pressing a button on the Control connected to the application on the Clean Me Check Me e It is possible to wake up the Clean ME Check Me in two ways to see the diode status 1 push a button on the CleanME CheckME this will wake up the CleanMe CheckME for 1 min but it will not wake up the CB 2 Push a button on a Control HB ACO this will wake up the CB and the Clean ME Check Me for 2 min Vbus power down time 1 min CME power down time 12 years end of life indication e If the start and Service Wash diodes start to blink the Clean Me Check me is out of battery power The battery is not replaceable the Clean Me Check Me must be replaced Page 15 of 24 Reset procedure of Clean Me Check Me CheckMe A gt Button 1 gt N Uy D ul m N 00 TE Button 2 40 j 94 Button 3 amb N UY amp vI HN e 0O 0n CleanMe Manual Reset e Button 1 check Me Button 3 Clean Me is held down for 5sec e Diode 8 begins to blink release buttons 1 or 3 and press down again in order to reset e The Check Me Clean Me is ready for use Diode 1 lights Automatic Reset after wash wash tunnel With the built in wash temperature sensor the Clean Me Check Me detects a wash when the temperature r
13. e that they do not play with the product It is important for everyone who is to connect install or use the systems to have the necessary information and access to this User Manual The appliance is not intended for use by young children or infirm E If there is visible damage to the product it must not be installed pa e persons without supervision pal Young children should be supervised to ensure that they do not play MY with the appliance Page 5 of 24 Residual risk A Some of the products contains software based components LINAK has done various possible efforts to assure that the software is free of errors and that the software has been developed according to the rules of IEC 60601 1 4 software in Medical products That involves Risk Analysis which shows a small residual risk for unwanted unintended movement of actuators under specific conditions According to the above rules it must be informed and if necessary considered in the Risk analysis of the final application More details to residual risk can be provided by LINAK if necessary Warning The plastic parts in the system cannot tolerate cutting oil Warning A LINAK s actuators and electronics are not constructed for use within the following fields e Planes and other aircrafts e Explosive environments e Nuclear power generation Warnings A If faults are observed the products must be replaced Never spray directly on the products with a high pressure cleane
14. eaches 50 C and counts the wash for Check Me and resets Clean me when the temperature drops below 40 C again Read out It is possible to read out the actual interval setting Push button 1 2 Check Me or 2 3 Clean ME for 10 sec The last saved settings will be shown If you do not want to change the settings don t make any further selections on the buttons 1 2 or 3 wait until the Clean Me Check Me confirm by blinking with the diodes shown Page 16 of 24 User interface configuration Clean Me CheckMe lt Button 2 k 2 3 4 AA o o o ooo 0 4 4 Button 3 t cleane Diode 1 7 Green Diode 8 Yellow Interval adjustment Both buttons 2 3 are pressed down for 10 sec Thereafter one of the diodes will start to blink It will always show the last used setting 4 default first time Press button 3 and the diode changes direction towards diode number 1 After reaching diode 1 it will start again at diode number 8 8 diode Wash now 7 diode Wash after 3 days 6 diode Wash after 7 days 5 diode Wash after 10 days 4 diode Wash after 14 days default installation 3 diode Wash after 18 days 2 diode Wash after 21 days 1 diode Wash after 30 days If no button is pressed for 5 sec the chosen diode blinks 3 times to confirm the setting The Clean Me system is ready for use The chosen interval is not updated before you have followed the reset procedure on page 9 Pressing buttons 2 3 during the
15. earth connection in LINAK Control Boxes class 1 it is recommended to use equipment delivering a test current of no less than 5A The resulting voltage will correspond to the resistance in the earth connection Test currents below 5A would yield no exact measurements Key to symbols The following symbols are used on the label on the LINAK products 0 R Type B equipment as per EN 60601 1 Lock function Protection against contact foreign Release function IPXX matter first character and water second character as per EN60529 Charge indicator Class 2 equipment ei For indoor use 8 Double insulated transformer D Protective earth Safety switch enable button r g Pr gt E Alternating Current oe Direct current Attention consult accompanying documents Page 12 of 24 O APPROVAL V94265 APPROVAL NO 97122 ee I U V Bauart gepr ft PRODUCT SERVICE ee es rere ieee ea a E i CS95145V LGA WPI Uy Du LISTED Demko approval Fimko approval Australian approval mark Australian approval mark Recognised Component Mark Canadian Recognised Component Mark Recognised Component Mark for Canada and the United States T Mark RW T v approval Tuv Produkt Service TUVRheinland ETL C ETL LGA UL Listing Mark C UL Listing Mark C UL US Listing Mark UL Listing Mark File E97199 File E175209 File E151104 OP gt O Xx
16. en diode blinks 3 times to confirm the setting and jumps to step 2 time setting Page 18 of 24 Step 2 e One of the diodes will start to blink 1 2 3 or 4 The last used setting will always be shown 1 default f rst time e Press button 1 and the diode changes direction towards 1 After o reaching diode 1 it will start again at number 4 g 4 diode Service after 1 month lt 3 diode Service after 3 months 2 diode Service after 6 months 1 diode Service after 12 months default installation e If no button is pressed for 5 sec the chosen diode blinks 3 times to confirm the setting and jmp to step 3 Step 3 Display e The diodes for wash 5 6 7 8 or the diodes for Time 1 2 3 4 will start to blink The last used settings will always Diodes 5 8 Display setting after wash default Diodes 1 4 Display setting after Time e If no button is pressed for 5 sec the chosen setting blinks 3 times to confirm the choice E be shown 5 e Press button 1 and the diodes change to light in 1 2 3 40r gt 5 6 7 8 A 2 e The Check Me system is ready for use The chosen interval is not updated before you have followed the reset procedure e Pressing buttons 1 2 during the interval adjustment will bring you back to the starting point again last saved setting Page 19 of 24 Labels ora ATEN Sia es MC z di Z a Battery Lifetime The built in battery is able to supply the necessary power to keep the
17. esponsibilities in relation to applying a LINAK product defined as hardware software technical advice etc related to an existing or new customer application LINAK products as defined above are applicable for a wide range of applications within the Medical Furniture Desk and Industry areas Yet LINAK cannot know all the conditions under which LINAK products will be installed used and operated as each individual application is unique The suitability and functionality of the LINAK product and its performance under varying conditions application vibration load humidity temperature frequency etc can only be verified by testing and shall ultimately be the responsibility of the LINAK customer using any LINAK product LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question Page 23 of 24 FACTORIES CHINA LINAK Shenzhen Actuator Systems Ltd Phone 86 75 58 61 06 656 Fax 86 75 58 61 06 990 E mail sales linak cn www linak cn SUBSIDIARIES AUSTRALIA LINAK Australia Pty Ltd Phone 61 38 79 69 777 Fax 61 38 79 69 778 E mail sales linak com au www linak com au AUSTRIA LINAK Reprasentanz Osterreich Wien Phone 43 1 890 74 46 Fax 43 1 890 74 46 15 E mail info linak de www linak at BELGIUM amp
18. ication is very dependent on how the products are used Maintenance e The LINAK products must be cleaned at regular intervals to remove dust and dirt and inspected for mechanical damage wear and breaks e The LINAK Clean Me amp Check Me are closed units and require no internal maintenance e IP 66 Washable tolerates being washed in tunnels e The LINAK products must be IP 66 washable when cleaning in wash tunnels Make sure that the plugs are correctly fitted with O rings before washing e O rings When individual parts are replaced in a LINAK IP66 or IP66 washable system the O rings on all parts must be replaced at the same time On control boxes with a replaceable mains fuse the O ring in the fuse cover must be replaced every time the cover has been removed The O rings must be greased in water free Vaseline when replacing them Make sure that the counterpart the socket is clean and undamaged e Electronics must be inspected at attachment points wires cabinet and plugs e Inspect the connections cables cabinet and plugs and check for correct functioning Page 9 of 24 IP Protection degree All LINAK products can be cleaned as followed according to their IP protection which is stated on the product label Cleaning instrucions Clean with a damp cloth Clean with a damp cloth Clean with a damp cloth Clean with a damp cloth Clean with a damp cloth IPX5 Wash with a brush and water but not water under pressure
19. in sorting of waste we can mention the following Metal plastic cable scrap combustible material and collection for recoverable resources Some of these main groups can be sub divided into groups e g metal can be divided into iron stainless steel and aluminium and alloy steel Plastic can e g be divided into ABS PA PE and PP The Clean Me amp Check Me can be disassembled and sorted into the following recycling groups Clean Me _ Plastic housing Plastic recycling or combustion amp Cable Cable scrap or combustion Check Me pc_board Electronics Scrap By now all our casted plastic units are provided with an interior code for plastic types and fiber contents if any Page 7 of 24 LINAK 3 WE IMPROVE YOUR LIFE DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY LINAK A S Smedevanget 8 DK 6430 Nordborg Name and address of the person authorized to compile the relevant technical documentation John Kling Group Headquarters Guderup DK 6430 Nordborg email jkli inak com Herewith declares that LINAK Actuators and Actuator Systems comply with the following parts of the Machinery Directive 2006 42 EC ANNEX Essential health and safety requirements relating to the design and construction of machinery 1 5 1 Electricity supply Directive 2006 95 EC on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits 1 5 10 Radiation
20. interval adjustment will bring you back to the starting point again last saved setting Page 17 of 24 User interface configuration Check Me The interval setting between inspections can be adjusted on demand choosing both services after washes and after time It is your choice which setting you want displayed after the interval adjustment Using the default settings as an example The user interface Check Me is set to service after 25 washes and 12 months It is the number of washes before service that the display will show moving from 1 8 where 8 time for service With default settings the service diode will light after 12 months are reached before the bed has been washed 25 times the displayed light will move to diode 8 to indicate time for service CheckMe Time Wash D a o e e 0 4 1 2 3 IN FB Display setting oe Button 2 a Button 1 CleanMe Service Interval adjustment is carried out in 3 steps Step 1 e Both buttons 1 2 are pressed down for 10 sec e Thereafter one of the diodes 5 8 will start to blink It will always show the last used setting 7 default first time e Press button 1 and the diode changes direction towards number 5 After reaching diode 5 it will start again at number 8 8 diode Service now 7 diode Service after 25 washes default installation 6 diode Service after 50 washes 5 diode Service after 100 washes After Washes e If no button is pressed for 5 sec the chos
21. must be complied with e They must not be highly alkaline or acidic pH value 6 8 e They must not contain caustic agents Page 10 of 24 e Their contents must not be able to change the structure of the surface or adhesion of the plastic e They must not break down grease The following disinfectants detergents are recommended e Neodischer Dekonta dosage 1 3 made by CHEMISCHE FABRIK Dr WEIGERT e CCOTRADE RW dosage 0 5 made by CCOTRADE GmbH Warning The systems must not be sprayed directly with a high pressure cleaner Mounting information e The Clean Me Check Me must be mounted vertically in order to maintain the IP degree Gore tex membrane At the rear of the product housing there is a gore tex membrane if this becomes damaged LINAK cannot guarantee the IP degree Environmental conditions Environment conditions 2222222 Operating SSS Temperature 5 C to 40 C Relative humidity 20 to 90 30 C not condensing Atmospheric pressure 700 to 1060 hPa storage PS Temperature 10 C to 50 C Relative humidity 20 to 90 30 C not condensing Atmospheric pressure 700 to 1060 hPa Valid where nothing otherwise is stated under the specific products in a later section Page 11 of 24 Insulation class LINAK control boxes are available in insulation class 1 and insulation class 2 Class 1 means with earth connection Class 2 means without earth connection When measuring the resistance in the
22. n nnnnrnrnnnnnnennnnnnns 17 User interface configuration Check Me ooocoooonococccncccocononnnononnnnnononnnnnnnnnnn nono nnnnnnnnrnrnnnnnn nn nn nn nnnnrnrnnnnnnnnnnnnnns 18 Troubleshooting labels o A E E E R Taree terre toe 20 Battery LISTING a 20 Drawing appendix ura vausudiuesdduanesouddusinar iaiaaeaia ei eaae bik lev aiei reie ienee 21 Declaration of CONTO ttrt nec cueanaeieek dokawaypun te nasee cee coecncawendauvervse te EEEE vaaseeeccetes 22 AOS die 24 Page 3 of 24 Preface We are delighted that you have chosen a product from LINAK LINAK systems are high tech products based on many years of experience in the manufacture and development of actuators electric control boxes controls and chargers This User Manual will tell you how to install use and maintain your LINAK electronics We are sure that your LINAK system will give you many years of problem free operation Before our products leave the factory they undergo full function and quality testing Should you nevertheless experience problems with your systems you are always welcome to contact your local dealer LINAK subsidiaries and some distributors situated all over the world have authorized service centres which are always ready to help you LINAK provides a warranty on all its products This warranty however is subject to correct use in accordance with the specifications maintenance being done correctly and any repairs being carried out at a service centre whi
23. r TE The LINAK products cannot tolerate the influence of strong solvents a basic or alkaline liquids Before installation re installation or troubleshooting e Stop the application e Switch off the power supply and pull out the mains plug e Relieve the application of any loads which may be released during the work Before start up e Make sure that the system has been installed as instructed in the User Manual e Make sure that the voltage of the control box is correct before the system is connected to the mains e System connection The individual parts must be connected before the control box is connected to the mains During operation e Ensure that the cables are not damaged e Unplug the mains cable on mobile equipment before it is moved Page 6 of 24 Repairs In order to avoid the risk of malfunction all repairs must only be carried out by authorized LINAK workshops or repairers as special tools must be used and special gaskets must be fitted Products under warranty must also be returned to authorized LINAK workshops Warning A If any of the LINAK products are opened there will be a risk of subsequent malfunction Disposal of LINAK s products LINAK s products may be disposed of possibly by dividing them into different waste groups for recycling or combustion We recommend that our product is disassembled as much as possible at the disposal and that you try to recycle it As an example of main groups with
Download Pdf Manuals
Related Search