User Manual - MSR Electronic
Contents
1. e At power up it emits a short beep and performs a 30 seconds countdown for the meter warm up then enters normal mode with current CO level and temperature readings displayed CO2PpM 5 2 Measurements The meter starts measurement when power on and updates the readings every second In case of operating environment change e g from high to low temp the sensor needs 30 seconds to respond Attention Do not hold the meter close to faces in case exhalation affects CO levels 5 3 Air Temperature The ambient air temperature is displayed down left 5 4 Data Hold Press the HOLD button to freeze the readings HOLD is displayed on the left top of the LCD All current readings are kept unchanged except STEL and TWA Press the HOLD button again to cancel the hold function 5 5 Backlight Hold down the MODE button for more than 1 second to activate and cancel backlight function 5 6 MIN MAX STEL TWA In normal mode press the MNX AV button to see the minimum maximum and weighted average readings With each press on the MNX AV button it displays MIN MAX STEL and TWA in sequence and returns to normal mode In MIN and MAX modes it shows the minimum and maximum readings of CO on the main display and of air on the lower display In STEL and TWA modes the main display shows the weighted average of CO readings for the past 15 minutes STEL and 8 hours TWA The lower display is the current air temperature Note2. C to 70 C Visualisation General performance O ABS PC blend Enclosure material ABS PC blend Dimensions H x W x D 209 x 70 x 58 mm Weight Approx 180 g Pe ee Approvals Listings po EMC Directive 89 336 EEC 1 year material PolyGard is a registered trademark of MSR GAPTB821160_E_0908 Tel 0049 0 8531 9004 0 Fax 0049 0 853 1 9004 54 Subject to technical changes MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de Made in Germany User Manual PolyGard CO Meter Va PTB821160 Besa An a coo MSR 13 Notes and General Information It is important to read this user manual thoroughly and clearly in order to understand the information and instructions The PolyGard devices must be used within product specification capabilities The appropriate operating and maintenance instructions and recommendations must be followed Due to on going product development MSR reserves the right to change specifications without notice The information contained herein is based upon data considered to be accurate However no guarantee is expressed or implied regarding the accuracy of this data 13 1 Intended Product Application The PolyGard devices are designed and manufactured for control applications and air quality compliance in commercial buildings and manufacturing plants 13 2 Installers Responsibilities It is the installer s responsibility to ensure that all PolyGard devices
3. 1 Ifthe meter is turned on for shorter than 15 minutes the STEL value will be the weighted average of readings taken since power on Same for TWA values appear before 8 hours 2 Ittakes at least 5 minutes to calculate STEL and TWA The display shows during the first 5 minutes from power on 3 While all readings are held unchanged STEL and TWA will keep updating every 5 minutes PolyGard is a registered trademark of MSR GAPTB821160_E_0908 Tel 0049 0 8531 9004 0 Fax 0049 0 8531 9004 54 Subject to technical changes MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de Made in Germany User Manual PolyGard CO Meter lan j R PTB821160 Page 6 el I 5 7 Alarm The meter features an audible alarm to give warnings when COs concentration exceeds the limit see P1 0 in setup for setting alarm threshold It emits beeps about 80dB when CO level goes over the set value and stops when any key but the SET button was pressed or readings fall below the set value lt beeps again when the value goes over the limit Restart the meter if the beeper can t be stopped 6 Auto Power Off The meter turns off automatically after 20 minutes of inactivity To override the function hold down the SET and the HOLD button for 2 seconds to turn on the meter until n appears NOTE Auto sleep function will be disabled during calibration mode 7 Setup Hold down the SET button in normal mode for more than
4. 1 sec to enter setup mode To exit setup press the CAL ESC button in P1 0 or P3 0 and it returns to normal mode Note P2 0 is not applicable in these models but for future model with CO and CO measurement 7 1 P1 0 CO Alarm When entering setup mode P1 0 and AL are displayed on the LCD Press the MNX AV button to go into P1 1 for setting the CO alarm threshold The current set value will be blinking on the LCD Press the MODE button to increase the value or the DP WBT button to decrease Each press tunes 100 ppm and the alarm range is from 100 to 9900 ppm When the preferred alarm value is set press the MNX AV button to save the settings or the CAL ESC button to return to P1 0 without saving 7 2 P3 0 Temperature Range Press the MODE button or the DP WBT button in P1 0 to access P3 0 for setting up temperature scale see fig Press the MNX AV button to access to P3 1 with blinking C or F current set on the lower left display To switch C or F press the MODE button and the DP WBT button Then press the MNX AV button to save the setting or the CAL ESC button to return to P3 0 without saving PolyGard is a registered trademark of MSR GAPTB821160_E_0908 Tel 0049 0 8531 9004 0 Fax 0049 0 853 1 9004 54 Subject to technical changes MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de Made in Germany User Manual PolyGard CO Meter ES PTB821160 MSR 8 CO Calibration The mete
5. GmbH shall not be liable for any incidental or consequential damages arising out of or related to the use of the PolyGard devices PolyGard is a registered trademark of MSR GAPTB821160_E_0908 Tel 0049 0 8531 9004 0 Fax 0049 0 853 1 9004 54 Subject to technical changes MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de Made in Germany
6. No 10 PolyGard is a registered trademark of MSR Tel 0049 0 8531 9004 0 Fax 0049 0 8531 9004 54 MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de Germany GAPTB821160_E_0908 Subject to technical changes Made in a User Manual PolyGard CO Meter qn PTB821160 Page 3 q Portable Carbon dioxide CO2 meter with temperature measurement 1 Description The portable PolyGard CO meter PTB821160 is designed to measure the carbon dioxide concentration and temperature in the surrounding air The two values are displayed on the large illuminated LCD simultaneously An audible alarm is included The integrated gold plated sensor is based on state of the art non dispersive infrared technology The built in data output RS232 makes it simple to log data The instrument is delivered with a hard carrying case batteries and manual 2 Application The portable instrument is used in residential commercial and industrial ranges for diagnosing ventilation and indoor air quality by measuring the carbon dioxide concentration Poor indoor air quality is considered unhealthy because it causes tiredness loss of ability to concentrate and even illness IAQ monitoring and survey especially on CO level and air ventilation become widely applied in public areas such as offices classrooms factories hospitals and hotels It is also applicable for measurements in incubators greenhouses mushroom farms e
7. are installed in compliance with all national and local codes and OSHA requirements Installation should be implemented only by technicians familiar with proper installation techniques and with codes standards and proper safety procedures for control installations and the latest edition of the National Electrical Code ANSI NFPA70 It is also essential to follow strictly all instructions as provided in the user manual 13 3 Maintenance It is recommended checking the PolyGard devices regularly Due to regular maintenance any performance deviations may easily be corrected Re calibration and part replacement in the field may be implemented by a qualified technician and with the appropriate tools 13 4 Limited Warranty MSR Electronic GmbH warrants the PolyGard device for a period of one 1 year from the date of shipment against defects in material or workmanship Should any evidence of defects in material or workmanship occur during the warranty period MSR Electronic GmbH will repair or replace the product at their own discretion without charge This warranty does not apply to units that have been altered had attempted repair or been subject to abuse accidental or otherwise The warranty also does not apply to units in which the sensor element has been overexposed or gas poisoned The above warranty is in lieu of all other express warranties obligations or liabilities This warranty applies only to the PolyGard device MSR Electronic
8. PolyGard PTB821160 Portable Carbon Dioxide Meter including Temperature Measurement User Manual September 2008 PolyGard is a registered trademark of MSR Tel 0049 0 853 1 9004 0 Fax 0049 0 8531 9004 54 MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de GAPTB821160_E_0908 Subject to technical changes Made in Germany User Manual PolyGard CO Meter AA MSR PTB821160 page 2 MOR 1 Description ii A ia 3 2 ANDO DNC QUO da acoce sie 3 3 A O 3 A gt FUncuonal DESCHIDUON esserne aa aaas aa teed wece 4 4 1 A ie ee ee ee 4 A27 ADDIS OA escuela se see eae 4 AS Keypads a ia 4 5 QDGFAUON aiii ia 5 5 1 FOIS OM ene ee ere ee eee Per mmr Rr nee er noe te ner Pe ner eee eee ee eee eee 5 IN ASUS Mot idiotas cet See ecm tetace 5 29 FAI FEMDOM AUO add 5 IA Wal Ol o on 5 2S A A E A eer er eee ee ee eee 5 96 MIN AX STEL TWA id 5 A 6 6 AUTO POWer Olla occ ia 6 FE SC 6 7 1 PEO GOA acotar toc a E a A 6 a IPOD emperalle IRAN ree Ou A 6 8 COSCAMA MIN ia 7 8 1 Calpa Uon ole saetas aladas 7 A o Ann A 7 TroUDIeSNOO UNO tb 7 10 PC CORMCCUON srt ina 8 11 CQ gt Levels and G ideliNeS ri 8 12 SDECMICATIONS sesiapa OKANANA aAa aE EAn EREE 9 13 Notes and General Information ccccccseeseeseceneecesesensesensesensesensesenseseneeses 10 132 Hended Product ADONCA ON ensce a a 10 132 IMSTAIGES RESPOMSIDINN CS a a a aaa a iaa 10 1383 Maltenanconni aid 10 134 MO A e a
9. alue stands for the average carbon dioxide level exposure during 8 hours working day is 5000 ppm 5 days STEL Short Term Exposure Limit value shows the last 15 minutes CO concentration and is 30 000 ppm ASHARE Standard 62 1989 Sec 6 1 3 Comfort odour criteria are likely to be satisfied if the ventilation rate is set so that 1 000 ppm of CO is not exceeded PolyGard is a registered trademark of MSR GAPTB821160_E_0908 Tel 0049 0 8531 9004 0 Fax 0049 0 853 1 9004 54 Subject to technical changes MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de Made in Germany User Manual PolyGard CO Meter i PTB821160 MISR 12 Specifications Electrica gt Gas Sensor Performance gt gt gt Sensor element Non dispersive infrared sensor with gold plated optical cell diffusion 2001 9999 ppm accuracy not specified Accuracy at NTP 25 C 5 of reading or 75 pom gt 15 years Pressure dependence 1 6 reading increase per kPa deviation from normal pressure Temperature Sensor Performance gt gt O Measuring range 10 C to 60 C Accuracy 1 0 5 C Logger and Software Logger and Software Digital interface Special cable RS232 option PC software Windows 95 98 NT ME 2000 XP software option Operating Environment OperatingEnvironment Humidity range 0 95 RH non condensing Working temperature 10 C to 50 C Storage temperature 20
10. apter cannot be used as a battery charger When the battery voltage gets low LH and Lob will appear on the display Additionally the beeper starts to sound In case of insufficient voltage the CO sensor is not able to work so it peeps to indicate a failed CO measurement The readings won t be displayed Press any key but to stop the beeping Please replace with fresh batteries or connect with an adapter Symbols Time weighted average value 8 hours Short term exposure limit 15 min average value Readings are freezed unchanged Minimum maximum readings Low battery indicator Air temperature Celsius Fahrenheit Turns on and off the meter Enters setup mode Sets as non sleep mode with Exits setup page mode Enters CO calibration with de Freezes the current readings Cancels the data hold function Activates or cancels the backlight Selects unit or increases a value in setup Selects unit or decreases a value in setup Activates MIN MAX STEL TWA function Saves and finishes settings PolyGard is a registered trademark of MSR Tel 0049 0 8531 9004 0 Fax 0049 0 853 1 9004 54 MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de Germany GAPTB821160_E_0908 Subject to technical changes Made in User Manual PolyGard CO Meter PTB821160 ES Ke tg Page 5 5 Operation 5 1 Power On Off e Press to turn the meter on and off
11. e air flow channels on the rear were blocked PolyGard is a registered trademark of MSR GAPTB821160_E_0908 Tel 0049 0 8531 9004 0 Fax 0049 0 8531 9004 54 Subject to technical changes MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de Made in Germany User Manual PolyGard CO Meter ian PTB821160 ae Error messages SN E01 CO sensor damaged E02 The value is under range E03 The value is over range E07 Too low voltage to measure COs Replace batteries or use an adaptor E17 Retry CO calibration E31 Temperature sensor damaged 10 PC Connection The meter can do PC link for on line logging and data analysis via RS232 interface and software The protocol is as follows A 9600 bps 8 data bits no parity B Format ASCII Cxxxxppm Txxx xC F LRC CRLF Description COz Air LRC CRLF 11 CO Levels and Guidelines The following are excerpts from ANSI ASHRAE addendum standard 62 1 2004 Enforceable and or regulatory levels e OSHA Occupational Safety and Health Administration 5000 ppm e MAK Maximale Arbeitsplatz Konzentration maximum allowable concentration 5000 ppm or 10000 ppm 1 h Non enforced guidelines and reference levels e Canadian 3500 long term e NIOSH U S National Institutes of Health 5000 ppm or 30000 ppm 15 min e ACGIH American Conference of Governmental Industrial Hygienists 5000 ppm or 30000 ppm Notes TWA Time Weighted Average v
12. r defaults to be calibrated manually in the ambient air where CO concentration is around 400 ppm Caution Do not calibrate the meter in the air with unknown CO concentration Otherwise it will be calibrated as 400 ppm by default and leads to inaccurate measurements 8 1 Calibration Site It is suggested to calibrate the CO sensor in fresh outdoor air that is well ventilated and better in sunny weather Do not calibrate the meter in places crowded with people or in places with high CO concentration such as ventilating outlets or fireplaces 8 2 Procedure Place the meter in the calibration site Turn on the meter and hold down the CAL ESC and the MODE buttons simultaneously to enter the CO calibration mode 400 ppm and CAL are blinking on the LCD while performing calibration Wait about 10 minutes until the blinking stops and the calibration is completed automatically and back to normal mode To abort the calibration turn off the meter at any time Note Ensure that the batteries are with full voltage during the calibration to prevent from interruption or failed calibration 9 Troubleshooting Trouble Solution Can t power on Press SET button for more than 0 3 seconds and try again Check whether the batteries are in good contact and correct polarity Check whether the adaptor is well plugged Fixed readings Check whether data hold function was activated HOLD icon at the left top Slow response Check whether th
13. tc where correct levels are essential 3 Features The meter contains the following features State of the art non dispersive infrared NDIR technology Measuring range 0 2000 ppm Data output RS232 Great liability and long term stability Audible alarm Internal batteries capacity more than 24 hours Internal automatic self diagnostic function Easy calibration Large clear LCD display temperature concentration for simultaneous display of current CO concentration and temperature Display of TWA 8 hours STEL 15 minutes minimum maximum and average values Pocket sized 209 x 70 x 58 mm Extremely light only 180g without batteries RS232 software Windows 95 98 NT ME 2000 XP software option Special cable for digital interface RS232 option Adapter 9 V 100 240 VAC Option PolyGard is a registered trademark of MSR GAPTB821160_E_0908 Tel 0049 0 8531 9004 0 Fax 0049 0 853 1 9004 54 Subject to technical changes MSR Electronic GmbH Wiirdinger Str 27 D 94060 Pocking www msr electronic de Made in Germany User Manual PolyGard CO Meter PTB821160 4 Functional Description 4 1 Power Supply The meter is powered by either 4 AA batteries or a DC adapter 9V 1A output 4 2 LCD Display Install the batteries into the battery compartment on the rear and make sure that they are in correct polarity and good contact When an adapter is used it will cut off the power supply from batteries The ad
Download Pdf Manuals
Related Search