USER MANUAL
Contents
1. Device message format Start Address optional Delimiter Sender_id message ICR Device long response Echoing command Address Body optional Sender_id command SF param param2 resull Delimiter CRI Carriage return ASCII 13 0x0D LF Line feed ASCII 10 0x0A ISP Space ASCII 32 0x20 FC 340 Kramer Protocol 10 2 Command Part Details Command Sequence of ASCII letters A Z a z and Command will separate from parameters with at least single space Parameters Sequence of Alfa Numeric ASCII chars 0 9 A Z a z and some special chars for specific commands parameters will be separated by commas Message string Every command must to be entered as part of message string that begin with message starting char and end with message closing char note that string can contain more then one command separated by pipe I char Message starting char for host command query for machine response Device address Optional for KNET KNET Device ID follow by char Query sign will follow after some commands to define query request Message closing char Host messages Carriage Return ASCII 13 will be referred to by CR in this document Machine messages Carriage Return ASCII 13 Line Feed ASCII 10 will be referred to by CRLF Spaces between param2. 1 Press the Enter button to display the menu The menu is displayed 2 Using the up A or down button move through the menu options until the flashing cursor is on Video Out Operating the FC 340 13 7 2 Press Enter The Video Out options are displayed Using the up 4 or down button move through the Video Out options until the flashing cursor is on Resolution Press Enter The Resolution options are displayed Using the up A or down button select the required output resolution Press Enter The selected output resolution is saved Note The CV output follows the frame rate of the selected resolution For 50Hz resolutions the PAL standard is used and for 59 94 60Hz resolutions NTSC is used Using the Menu The menu is shown on the display when the Enter button is pressed If there is no button activity for approximately 30 seconds the display reverts back to the Input Output display Navigation through the menu is performed as follows Enter display the menu or select a parameter value Up 4 or Right gt scroll up through the parameter value list Down or Left lt scroll down through the parameter value list ESC Move to the first level menu The main menu comprises six sections Video Out see Section 7 2 1 Audio Out see Section 7 2 2 Status see Section 7 2 3 Comm Settings see Section 7 2 4 System see Section 7 2 5 7 2 1 Video Out Sub menu Th
3. 2 1 Achieving the Best Performance 2 2 Safety Instructions 2 3 Recycling Kramer Products 3 Overview 4 Defining the FC 340 5 Installing the FC 340 in a Rack 6 Connecting the FC 340 6 1 Connecting a Serial Controller to the FC 340 6 2 Connecting to the FC 340 via Ethernet 6 3 Connecting the Balanced Unbalanced Stereo Audio Output 7 Operating the FC 340 7 1 Changing the Output Resolution 7 2 Using the Menu 7 3 Resetting the Device to Factory Default Configuration 7 4 Locking and Unlocking the Front Panel 7 5 Updating the Firmware Using the K Upload Software 8 Technical Specifications 9 Default Parameters 9 1 Default Communication Parameters 10 Kramer Protocol 10 1 Protocol 3000 Syntax 10 2 Command Part Details 10 3 Kramer Protocol 3000 Commands Figures Figure 1 FC 340 SDI Scaler Embedder Scan Converter Front Panel Figure 2 FC 340 SDI Scaler Embedder Scan Converter Rear Panel Figure 3 Connecting the FC 340 SDI Scaler Embedder Scan Converter Figure 4 Local Area Connection Properties Window Figure 5 Internet Protocol TCP IP Properties Window Figure 6 Balanced Stereo Audio Connection Figure 7 Unbalanced Stereo Audio Connection ODAN O RA ONNN Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a
4. Overview The FC 340 SDI Scaler Embedder Scan Converter is ideal as a broadcast quality video scaler and audio embedder de embedder for digital signals up to 3G HD SDI All mentions of SDI in this manual include signals up to and including 3G HD SDI The FC 340 features e Amaximum data rate of 3Gpbs e 1 SDI video input and 2 SDI video outputs e 1 re clocked looping video output e 1 composite video output e 1 balanced audio output e 2 AES 3id audio inputs and 2 AES 3id audio outputs Note Some machines may have AES EBU printed instead of AES 3id e The option to select either the embedded audio or to embed two independent audio groups e Kramer reKlocking amp Equalization Technology that rebuilds the digital signal to travel longer distances e An LCD text display for easy configuration and operation MAIA2AO ObE O4 4 Defining the FC 340 Figure 1 defines the front panel of the FC 340 SDI Scaler Embedder Scan Converter Figure 1 FC 340 SDI Scaler Embedder Scan Converter Front Panel Function LCD Readout Displays either the input output resolution currently selected or the menu during configuration 2 Menu Navigation Buttons Press the Enter up A down left lt 4 and right buttons to navigate the menu and modify parameters or values see Section 7 2 PANEL LOCK Button Press and hold to lock the front panel buttons Press and hold again to unlock the buttons see Section 7 4 4 ESC
5. Area Connection Properties General Advanced Connect using E9 Intel R 82566DC 2 Gigabit Network C This connection uses the following items M II Client for Microsoft Networks A File and Printer Sharing for Microsoft Networks dE QoS Packet Scheduler Internet Protocol TCP IP Description Allows your computer to access resources on a Microsoft network C Show icon in notification area when connected Notify me when this connection has limited or no connectivity Figure 4 Local Area Connection Properties Window FC 340 Connecting the FC 340 6 Select Use the following IP Address and enter the details as shown in Figure 5 You can use any IP address in the range 192 168 1 1 to 192 168 1 255 excluding 192 168 1 39 that is provided by your IT department Internet Protocol TCP IP Properties eT General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings Obtain an IP address automatically Use the following IP address IP address 192 168 1 38 Subnet mask 255 255 255 0 Default gateway 9 0 0 0 Use the following DNS server addresses Preferred DNS server Altemate DNS server Figure 5 Internet Protocol TCP IP Properties Window 7 Click OK 6 2 2 Connecting to the Ethernet Port vi
6. power surges or other acts of nature This limited warranty does not cover any damage deterioration or malfunction resulting from the installation or removal of this product from any installation any unauthorized tampering with this product any repairs attempted by anyone unauthorized by Kramer Electronics to make such repairs or any other cause which does not relate directly to a defect in materials and or workmanship of this product This limited warranty does not cover cartons equipment enclosures cables or accessories used in conjunction with this product Without limiting any other exclusion herein Kramer Electronics does not warrant that the product covered hereby including without limitation the technology and or integrated circuit s included in the product will not become obsolete or that such items are or will remain compatible with any other product or technology with which the product may be used How Long Does this Coverage Last Seven years as of this printing please check our Web site for the most current and accurate warranty information Whois Covered Only the original purchaser of this product is covered under this limited warranty This limited warranty is not transferable to subsequent purchasers or owners of this product What Kramer Electronics will do Kramer Electronics will at its sole option provide one of the following three remedies to whatever extent it shall deem necessary to satisfy a proper claim un
7. Button Press to move back one level through the menu see Section 7 2 Figure 2 defines the rear panel of the FC 340 Ove 949u4 Bulud Ove O4 Figure 2 FC 340 SDI Scaler Embedder Scan Converter Rear Panel Connect to a balanced audio acceptor see Section 6 Connect to a balanced audio acceptor Connect to a serial controller see Section 6 1 Connect to a PC controller via a LAN see Section 6 2 6 INSDIBNC Connector sis Connect to an SDI signal source Press and hold while switching on the device to reset to factory default H RESET Button parameters see Section 9 IN TBNG Connector AESA 5 Installing the FC 340 in a Rack Before installing in a rack be sure that the environment is within the recommended range OPERATING TEMPERATURE STORAGE TEMPERATURE HUMIDITY T CAUTION When installing on a 19 rack avoid hazards by taking care that 1 Itis located within the recommended environmental conditions as the operating ambient temperature of a closed or multi unit rack assembly may exceed the room ambient temperature 2 Once rack mounted enough air will still flow around the machine 3 The machine is placed straight in the correct horizontal position 4 You do not overload the circuit s When connecting the machine to the supply circuit overloading the circuits might have a detrimental effect on overcurrent protection and supply wiring Refer to the appropriate nameplate ratings for info
8. D UNDER APPLICABLE LAW Other Conditions This limited warranty gives you specific legal rights and you may have other rights which vary from country to country or state to state This limited warranty is void if i the label bearing the serial number of this product has been removed or defaced ii the product is not distributed by Kramer Electronics or iii this product is not purchased from an authorized Kramer Electronics reseller If you are unsure whether a reseller is an authorized Kramer Electronics reseller please visit our Web site at www kramerelectronics com or contact a Kramer Electronics office from the list at the end of this document Your rights under this limited warranty are not diminished if you do not complete and return the product registration form or complete and submit the online product registration form Kramer Electronics thanks you for purchasing a Kramer Electronics product We hope it will give you years of satisfaction For the latest information on our products and a list of Kramer distributors visit our Web site where updates to this user manual may be found We welcome your questions comments and feedback Web site www kramerelectronics com KRAMER E mail info kramerel com SAFETY WARNING Disconnect the unit from the power supply before opening and servicing P N 2900 000768 Rev 4
9. ESULTING FROM ANY BREACH OF WARRANTY OR CONDITION OR UNDER ANY OTHER LEGAL THEORY Some countries districts or states do not allow the exclusion or limitation of relief special incidental consequential or indirect damages or the limitation of liability to specified amounts so the above limitations or exclusions may not apply to you Exclusive Remedy TO THE MAXIMUM EXTENT PERMITTED BY LAW THIS LIMITED WARRANTY AND THE REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES REMEDIES AND CONDITIONS WHETHER ORAL OR WRITTEN EXPRESS OR IMPLIED TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IF KRAMER ELECTRONICS CANNOT LAWFULLY DISCLAIM OR EXCLUDE IMPLIED WARRANTIES UNDER APPLICABLE LAW THEN ALL IMPLIED WARRANTIES COVERING THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY TO THIS PRODUCT AS PROVIDED UNDER APPICABLE LAW IF ANY PRODUCT TO WHICH THIS LIMITED WARRANTY APPLIES IS A CONSUMER PRODUCT UNDER THE MAGNUSON MOSS WARRANTY ACT 15 U S C A 2301 ET SEQ OR OTHER APPICABLE LAW THE FOREGOING DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO YOU AND ALL IMPLIED WARRANTIES ON THIS PRODUCT INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR THE PARTICULAR PURPOSE SHALL APPLY AS PROVIDE
10. KRAMER ELECTRONICS LTD USER MANUAL MODEL FCc 340 SDI Scaler Embedder Scan Converter P N 2900 000768 Rev 4 FC 340 SDI Scaler Embedded Scan Converter Quick Start Guide This guide helps you install and use your product for the first time For more detailed information go to h http www kramerelectronics com support product_downloads asp to download the latest manual or scan the k QR code on the left Step 1 Check what s in the box A FC 340 SDI Scaler Embedder Scan Converter A 1 Quick Start Guide Power cord 2 Rack ears 4 Rubber feet Step 2 Install the FC 340 Mount the device in a rack using the supplied rack ears or place it on a shelf Step 3 Connect the inputs and outputs Switch off the power to all devices before connecting them to your FC 340 Oma q a ey eS CT Ge 8 io WY ODO OSs ng N AA AA AOC ONGA OAAR SASS 2N Step 4 Connect the power a Connect the FC 340 to the mains supply using the supplied power cord Step 5 Operate the device Operate the device using the front panel controls RS 232 and Ethernet as Press and hold to lock the front panel buttons EY E Press and hold again to unlock the buttons Use the keypad to navigate the menu and modify parameters Kon esc lt y O Press ESC to move back one level in the menu Contents 1 Introduction 2 Getting Started
11. a a Network Switch Hub To connect to the Ethernet port on the FC 340 via a network switch hub e Connect the PC to the Ethernet network switch hub using a straight through cable FC 340 Connecting the FC 34 6 3 Connecting the Balanced Unbalanced Stereo Audio Output This section illustrates how to wire the devices to the balanced audio output e A balanced stereo output connection see Figure 6 e Anunbalanced stereo output connection see Figure 7 L L G R R Figure 6 Balanced Stereo Audio Connection L L G R R Figure 7 Unbalanced Stereo Audio Connection FC 340 Connecting the FC 340 7 1 Operating the FC 340 In general operation the video signal received on the SDI IN connector is output simultaneously on both SDI OUT connectors as well as the composite video ANALOG OUTPUT connector The audio embedded in the SDI input signal is output on both AES 3id connectors simultaneously as well as on the balanced audio ANALOG OUTPUT When the FC 340 is powered on the following is displayed briefly FC340 KRAMER The device then performs a self test If the test is successful the Menu is displayed as shown below VIDEO OUT gt AUDIO OUT gt If there is no button activity for approximately 30 seconds the display reverts to displaying the input status and output resolution similar to that shown below IN unlocked OUT 1080p59 94 Changing the Output Resolution To change the output resolution
12. a an RS 232 connection using for example a PC To connect to the FC 340 via RS 232 e Connect the 3 pin terminal block on the rear panel port of the FC 340 pin G to pin 5 pin Rx to pin 3 pin Tx to pin 2 to the RS 232 9 pin D sub port on your PC Connecting to the FC 340 via Ethernet You can connect the FC 340 via Ethernet via either of the following methods e A crossover cable see Section 6 2 1 for direct connection to the PC e A straight through cable see Section 6 2 2 for connection via a network hub or network router After connecting the Ethernet port you have to install and configure your Ethernet Port For detailed instructions see the Ethernet Configuration Guide Lantronix in the technical support section on our Web site http www kramerelectronics com 6 2 1 Connecting the Ethernet Port Directly to a PC You can connect the Ethernet port on the FC 340 to the Ethernet port on your PC via a crossover cable with RJ 45 connectors This type of connection is recommended for identification of the factory default IP Address of the FC 340 during the initial configuration To configure your PC after connecting the Ethernet port 1 Right click the My Network Places icon on your desktop 2 Select Properties 3 Right click Local Area Connection Properties 4 Select Properties The Local Area Connection Properties window appears 5 Select the Internet Protocol TCP IP and click the Properties Button t Local
13. d display the serial communications values Parameter NETWORK IP address Sets the IP network address Any valid IP address Default 192 168 001 039 IP mask Sets the IP network mask Any valid subnet Default 255 255 000 000 IP gateway Sets the IP gateway address Any valid gateway address Default 000 000 000 000 IP port Sets the IP port number Any valid TCP port Default 05000 RS 232 Baud Displays the baud rate 115200 Parity Displays the parity bit setting none 7 2 5 System Sub menu The parameters in the System sub menu display the device versions and set the LCD display characteristics Parameter Description FIRMWARE The device firmware version FPGA VER The device FPGA version S N The device serial number 7 3 Resetting the Device to Factory Default Configuration To reset the device to the factory default configuration 1 Turn the device off Press and hold the Reset button on the rear panel of the device While holding the button depressed turn the device on Hold the button depressed for 10 seconds and release the button The configuration is reset to the factory default 7 4 7 5 Locking and Unlocking the Front Panel You can lock the front panel buttons to prevent unwanted key presses from changing the current configuration To lock the front panel e Press and hold the Panel Lock button The button lights the Locked message is displayed b
14. daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Routers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters and GROUP 11 Sierra Products Congratulations on purchasing your FC 340 SDI Scaler Embedder Scan Converter which is ideal for broadcast and production studios as well as digital and analog AV authoring 2 1 2 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual to check for up to date user manuals application programs and to check if firmware upgrades are available where appropriate i Go to http www kramerelectronics com support product_downloads asp Achieving the Best Performance To achieve the best performance e Use only good quality connection cables we recommend Kramer high performance high resolution cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated
15. der this limited warranty 1 Elect to repair or facilitate the repair of any defective parts within a reasonable period of time free of any charge for the necessary parts and labor to complete the repair and restore this product to its proper operating condition Kramer Electronics will also pay the shipping costs necessary to return this product once the repair is complete 2 Replace this product with a direct replacement or with a similar product deemed by Kramer Electronics to perform substantially the same function as the original product 3 Issue a refund of the original purchase price less depreciation to be determined based on the age of the product at the time remedy is sought under this limited warranty What Kramer Electronics will not do Under This Limited Warranty If this product is returned to Kramer Electronics or the authorized dealer from which it was purchased or any other party authorized to repair Kramer Electronics products this product must be insured during shipment with the insurance and shipping charges prepaid by you If this product is returned uninsured you assume all risks of loss or damage during shipment Kramer Electronics will not be responsible for any costs related to the removal or re installation of this product from or into any installation Kramer Electronics will not be responsible for any costs related to any setting up this product any adjustment of user controls or any programming required for a specif
16. e parameters in the Video Out sub menu set the output video characteristics Parameter Resolution Sets the output 1080p59 94 1080p60 1080p50 NTSC PAL resolution 720p59 94 720p60 720p50 1080i59 94 1080i60 1080i50 Default 720p 59 94 Genlock Sets the source for No Genlock Input Mode the genlock signal Default No Genlock Note The CV output frame rate follows the above settings see Section 7 1 7 2 2 Audio Out Sub menu The parameters in the Audio Out sub menu set the audio output characteristics Embedding gt Sets the audio group to Off Embedded input AES input embed Group 1 Group Default Embedded input 2 Group 3 and Group 4 AES Out 1 Embeds the AES audio Gr Pair1 Gri Pair2 Gr2 Pair1 Gr2 Pair2 input 1 Gr3 Pair1 Gr3 Pair2 Gr4 Pair1 Gr4 Pair2 AES In1 AES In2 Off Default Gr1 Pair1 AES Out 2 Embeds the AES audio Gr Pair1 Gri Pair2 Gr2 Pair1 Gr2 Pair2 input 2 Gr3 Pair1 Gr3 Pair2 Gr4 Pair1 Gr4 Pair2 AES In1 AES In2 Off Default Gr1 Pair2 7 2 3 Status Sub menu The parameters in the Status sub menu display the input conditions Video Input gt Displays the locked unlocked status of the video format and genlock Displays the audio group status Format Unlocked Genlock Unlocked G1 G2 G3 G4 Audio Input FC 340 Operating the FC 3 tU 7 2 4 Comm Settings Sub menu The parameters in the Comm Settings sub menu set the network IP an
17. eters or command parts will be ignored Commands chain separator char When message string contains more than one command commands will be separated by pipe I YY Commands entering If terminal software used to connect over serial ethernet USB port that possible to directly enter all commands characters CR will be entered by Enter key that key send also ILA but this char will be ignored by commands parser Sending commands from some controllers like Crestron require coding some characters in special form like X Anyway there is a way to enter all ASCII characters so it is possible to send all commands also from controller Similar way can use for URL Telnet support that maybe will be added in future Commands forms Some commands have short name syntax beside the full name to allow faster typing response is always in long syntax Commands chaining It is possible to enter multiple commands in same string by l char pipe In this case the message starting char and the message closing char will be entered just one time in the string beginning and at the end All the commands in string will not execute until the closing char will be entered Separate response will be sent for every command in the chain Input string max length 64 characters Backward support Design note transparent supporting for protocol 2000 will be implemented by switch protocol command from pr
18. g to output frame rate Digital Audio _ 2 AES 3id audio on BNC connectors Sample conversion rate 48kHz Analog Audio __ 2 Balanced stereo audio on a 5 pin terminal block Bandwidth 20kHz POWER CONSUMPTION 100 240V AC 50 60Hz 22VA OPERATING TEMPERATURE 0 to 40 C 32 to 104 F STORAGE TEMPERATURE 40 to 70 C 40 to 158 F HUMIDITY 10 to 90 RHL non condensing DIMENSIONS 19 x 7 2 x 1U W D H rack mountable WEIGHT 1 6kg 3 53lbs approx ACCESSORIES Rack ears pecificatio 9 Default Parameters 9 1 Default Communication Parameters RS 232 C Soss hooo SyS C Nn Ethernet FC 340 Default Pa 10 10 1 Kramer Protocol The FC 340 supports the Kramer Protocol 3000 The Protocol 3000 RS 232 communication protocol lets you control the machine from any standard terminal software for example Windows HyperTerminal Application Protocol 3000 Syntax Host message format Address Body Delimiter optional Destination_id message Simple command commands string with only one command without addressing start body delimiter Command SP Parameter_1 Parameter_2 CRI Commands string formal syntax with commands concatenation and addressing Address Command_1 Parameter1_1 Parameter1_2 Command_2 Parameter2_1 Parameter2_2 Command_3 Parameter3_1 Parameter3_2 CRI
19. ic installation of this product How to Obtain a Remedy under this Limited Warranty To obtain a remedy under this limited warranty you must contact either the authorized Kramer Electronics reseller from whom you purchased this product or the Kramer Electronics office nearest you For a list of authorized Kramer Electronics resellers and or Kramer Electronics authorized service providers please visit our web site at www kramerelectronics com or contact the Kramer Electronics office nearest you In order to pursue any remedy under this limited warranty you must possess an original dated receipt as proof of purchase from an authorized Kramer Electronics reseller If this product is returned under this limited warranty a return authorization number obtained from Kramer Electronics will be required You may also be directed to an authorized reseller or a person authorized by Kramer Electronics to repair the product If itis decided that this product should be returned directly to Kramer Electronics this product should be properly packed preferably in the original carton for shipping Cartons not bearing a return authorization number will be refused Limitation on Liability THE MAXIMUM LIABILITY OF KRAMER ELECTRONICS UNDER THIS LIMITED WARRANTY SHALL NOT EXCEED THE ACTUAL PURCHASE PRICE PAID FOR THE PRODUCT TO THE MAXIMUM EXTENT PERMITTED BY LAW KRAMER ELECTRONICS IS NOT RESPONSIBLE FOR DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES R
20. otocol 3000 to protocol 2000 in protocol 2000 there is already such a command to switch protocol to ASCII protocol 56 H38 H80 H83 H81 FC 340 Kramer Protocol Par 10 3 Kramer Protocol 3000 Commands Full details for each command are presented in the Kramer Protocol 3000 document available for download from http www kramerelectronics com Cmd Command Short Description Permission ft T T Protocolhandshaking EndUser BULD DATE Read device buld dato EndUsr FACTORY Resetto factory defaut configuration mee f ist ofcommands End User i PFW f oad new firmware User SW mema moo Readaevicemod Enduser PROT veER Read device protocol version EndUser PRESET Reset device d Administrator _ SN Read device serialnumber Enduser venson Read device firmware version EndUser____ FC 340 Kramer Protocol LIMITED WARRANTY The warranty obligations of Kramer Electronics for this product are limited to the terms set forth below Whatis Covered This limited warranty covers defects in materials and workmanship in this product What is Not Covered This limited warranty does not cover any damage deterioration or malfunction resulting from any alteration modification improper or unreasonable use or maintenance misuse abuse accident neglect exposure to excess moisture fire improper packing and shipping such claims must be presented to the carrier lightning
21. r to all devices before connecting them to your FC 340 After connecting your FC 340 connect its power and then switch on the power to the other devices Composite Video Recorder Amplifier Digital Camera Display 1 Display 2 DAT Recorder Figure 3 Connecting the FC 340 SDI Scaler Embedder Scan Converter To connect the FC 340 as illustrated in the example in Figure 3 1 Connect an SD HD 3G HD SDI source for example an HD digital video camera to the SDI IN BNC connector 2 Connect the SDI OUT 1 BNC connector to an SDI acceptor for example an SDI display FC 340 Connecting the FC 340 6 1 6 2 FC 340 Connecting the FC 340 3 Connect the SDI OUT 2 BNC connector to an SDI acceptor for example an SDI display 4 Connect the CV ANALOG OUTPUT BNC connector to a composite video acceptor for example a composite video recorder See the Note in Section 7 1 5 Connect the CV 5 pin terminal block to a balanced audio acceptor for example an amplifier 6 Connect AES digital audio sources for example DAT players to the AES 3id IN 1 and IN 2 BNC connectors 7 Connect the AES 3id OUT 1 BNC connector to an AES digital audio acceptor for example a DAT recorder Some machines may have AES EBU printed instead of AES 3id 8 Optional Connect a controller via either RS 232 or a LAN to the Ethernet RJ 45 connector Connecting a Serial Controller to the FC 340 You can connect to the FC 340 vi
22. riefly and the front panel buttons are locked Pressing any button causes the Locked message to display briefly and the Panel Lock button to flash To unlock the front panel e Press and hold the Panel Lock button The button no longer lights and the front panel buttons are unlocked Updating the Firmware Using the K Upload Software The FC 340 uses a microcontroller that runs firmware located in flash memory The latest version of firmware and upgrade instructions Kramer K Upload Guide can be downloaded from the Kramer Web site at http www kramerelectronics com 340 Operating the FC 340 i 17 8 Technical Specifications INPUTS Digital Video 1 SDI serial video 75Q on SD SMPTE 259M SMPTE 125M 480i 59 94 BNC connectors ITU R BT 656 5_ 576i 50 HD SMPTE 292 SMPTE 296M 720p 59 94 60 50 SMPTE 274M 1080i 59 94 60 50 1080p 29 97 30 25 23 98 24 23 98sF 24sF 3G SMPTE 424M SMPTE 296M 1080p 59 94 60 50 Max input level 800mVpp 75Q Digital Audio 2 AES 3id audio on BNC Sample conversion rate 48kHz connectors OUTPUTS Digital Video 2 SDI video 750 on BNC SD SMPTE 259M SMPTE 125M 480i 59 94 connectors ITU R BT 656 5 576i 50 HD SMPTE 292M SMPTE 296M 720p 59 94 60 50 SMPTE 274M 1080i 59 94 60 50 3G__ SMPTE 424M SMPTE 296M 1080p 59 94 60 50 Max output level 800mVpp 75Q Analog Video _ 1 Composite on a BNC connector PAL NTSC accordin
23. rmation For example for fuse replacement see the value printed on the product label 5 The machine is earthed grounded in a reliable way and is connected only to an electricity socket with grounding Pay particular attention to situations where electricity is supplied indirectly when the power cord is not plugged directly into the socket in the wall for example when using an extension cable or a power strip and that you use only the power cord that is supplied with the machine O to 40 C 32 to 104 F 40 to 70 C 40 to 158 F 10 to 90 RHL non condensing FC 340 Installing the FC 340 in a Rack To rack mount a machine 1 Attach both ear brackets to the machine To do so remove the screws from each side of the machine 3 on each side and replace those screws through the ear brackets 2 Place the ears of the machine against the rack rails and insert the proper screws not provided through each of the four holes in the rack ears Note In some models the front panel may feature built in rack ears Detachable rack ears can be removed for desktop use Always mount the machine in the rack before you attach any cables or connect the machine to the power If you are using a Kramer rack adapter kit for a machine that is not 19 see the Rack Adapters user manual for installation instructions available from our Web site 6 Connecting the FC 340 Switch off the powe
24. with low quality cables e Do not secure the cables in tight bundles or roll the slack into tight coils e Avoid interference from neighboring electrical appliances that may adversely influence signal quality e Position your Kramer FC 340 away from moisture excessive sunlight and dust This equipment is to be used only inside a building It may only be connected to other equipment that is installed inside a building Safety Instructions Caution There are no operator serviceable parts inside the unit Warning Use only the power cord that is supplied with the unit Warning Do not open the unit High voltages can cause electrical shock Servicing by qualified personnel only Warning Disconnect the power and unplug the unit from the wall before installing 340 Getting Started 2 3 Recycling Kramer Products The Waste Electrical and Electronic Equipment WEEE Directive 2002 96 EC aims to reduce the amount of WEEE sent for disposal to landfill or incineration by requiring it to be collected and recycled To comply with the WEEE Directive Kramer Electronics has made arrangements with the European Advanced Recycling Network EARN and will cover any costs of treatment recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility For details of Kramer s recycling arrangements in your particular country go to our recycling pages at http www kramerelectronics com support recycling
Download Pdf Manuals
Related Search