Reader Programming Guide
Contents
1. Colour Function Description Pink BELL_A Doorbell button one end Pale blue BELL B Doorbell button to the other end Green DO WG output DO White D1 WG output D1 Grey ALARM Alarm negative alarm positive connected 12 V Yellow OPEN Exit button one end the other end connected GND Brown D_IN Magnetic switch one end the other end connected GND Red 12V 12V DC Regulated Power Input Black GND 12V DC Regulated Power Input Blue NO Relay normally on end Connect positive electric lock Purple COM Relay Public end connect GND Orange NC Relay Closed end connect negative electric lock Magnetic lock and Fail Safe lock diagram Wiring Guide For Fail Safe Locks With D8P Output Expander Connections Labels May Vary with REX Device Brand Example REX Motion Sensor Example Exit Button Rerferance Button Manual for Contact Information LED c NONC naan Referance your owners manual for actual contact configuration Purple Common 18 6 Stranded Cable Yellow REX Magnetic Lock Fail Safe Lock S Electric Strike and Fail Secure wiring diagram Wiring Guide For Fail Safe Locks With D8P Output Expander Connections Labels May Vary with REX Device Brand Purple Comman BLUE NO Yellow REX 18 2 or 18 4 Stranded Cable Orange NC 8 To Reset to Factory Default a Disconnect power from the unit b Press and ho2. 2 User ID number for a PIN user or 2 Read Card for a card user Users can be deleted continuously without exiting programming mode To unlock the door for a PIN user Enter the PIN then press To unlock the door for a card user Present the card 3 Description The unit is single door multifunction standalone access controller or a Wiegand output keypad or card reader It is suitable for mounting either indoor or outdoor in harsh environments It is housed in a strong sturdy and vandal proof Zinc Alloy electroplated case which is available in either a bright silver or matt silver finish The electronics are fully potted so the unit is waterproof and conforms to IP68 This unit supports up to 2000 users in either a Card 4 digit PIN or a Card PIN option The inbuilt card reader supports 125KHZ EM cards 13 56MHz Mifare cards The unit has many extra features including lock output current short circuit protection Wiegand output and a backlit keypad These features make the unit an ideal choice for door access not only for small shops and domestic households but also for commercial and industrial applications such as factories warehouses laboratories banks and prisons 4 Features Waterproof conforms to IP68 Strong Zinc Alloy Electroplated anti vandal case Full programming from the keypad 2000 uses supports Card PIN Card
3. Alarm and inside buzzer operate 72 To remove the alarm To reset the Door Forced Open warning Read valid cardi or Master Code To reset the Door Open Too Long warning Close the door or Read valid cardi or Master Code 10 12 The unit operating as a Wiegand Output Reader In this mode the unit supports a Wiegand 26 bit output so the Wiegand data lines can be connected to any controller which supports a Wiegand 26 bit input BELL_A g BELL_B DO D1 ALARM OPEN D_IN 12V GND NO Access Controller COM Purple Orange NC lt n Connect 11
4. PIN Can be used as a stand alone keypad Backlight keys Wiegand 26 input for connection to external reader Wiegand 26 output for connection to a controller Adjustable Door Output time Alarm time Door Open time Very low power consumption 30mA Fast operating speed lt 20ms with 2000 users Lock output current short circuit protection Easy to install and program Built in light dependent resistor LDR for anti tamper Built in buzzer Red Yellow and Green LEDS display the working status 5 Specifications Operating Voltage DC 12V 10 User Capacity 2000 Card Reading Distance 3 6 cm Active Current lt 60mA Idle Current 25 5 mA Lock Output Load Max 3A Alarm Output Load Max 20A Operating Temperature 45 C 60 C Operating Humidity 10 90 RH Waterproof Conforms to IP68 Adjustable Door Relay time 0 99 seconds Adjustable Alarm Time 0 3 minutes Wiegand Interface Wiegand 26 bit Wiring Connections Electric Lock Exit Button External Alarm External reader 6 Installation Remove the back cover from the keypad using the supplied special screw driver Drill 2 holes on the wall for the Self tapping screws and hole for the cable Put the supplied rubber bungs to into the two holes Fix the back cover firmly on the wall with 2 Self tapping screws Thread the cable through the cable hole Attach the keypad to the back cover 7 Wiring
5. programming mode User ID is allocated to a card Only one user ID can be allocated to a single card To add a card user Method 3 1 Card number Card number is the last 8 digits printed User can be added continuously without exiting on the back of the card user ID number Programming mode auto generation To add a card user Method 4 1 ID number Card number In this method a User ID is allocated toa User can be added continuously without exiting card number Only one user ID can be programming mode allocated to the card number To delete a card user by card Note users 2 Read Card can be deleted continuously without exiting programming mode To delete a card user by user ID This 2 UserID option can be used when a user has lost their card To delete a card user by card number 2 Card number This option can be used when the user Note users can be deleted continuously without want to make the change but the card exiting programming mode has lost To add a card and PIN user in card and PIN mode 8 1 To Add a card and Pin user Add the card as for a card user The PIN is any four digits between 0000 Press to exit from the programming mode amp 9999 with the exception of 1234 which Then a
6. 7 0 99 is to set the door relay time 0 99 seconds Door Open Detection Door Open Too Long DOTL warning When used with an optional magnetic contact or built in magnetic contact of the lock if the door is opened normally but not closed after 1 minute the inside buzzer will beep automatically to remind people to close the door and continue for 1 minute before switching off automatically Door Forced Open warning When used with an optional magnetic contact or built in magnetic contact of the lock if the door is forced open or if the door is opened after 20 seconds the inside buzzer and alarm output will both operate The Alarm Output time is adjustable between 0 3 minutes with the default being 1 minute To disable door open detection Factory 6 0 default To enable door open detection 6 1 1 Alarm output time To set the alarm output time 0 3 minutes 5 0 3 Factory default is 1 minute Keypad Lockout amp Alarm Output options If there are 10 invalid cards or 10 incorrect PIN numbers in a 10 minute period either the keypad will lockout for 10 minutes or both the alarm and the inside buzzer will operate for 10 minutes depending on the option selected below Normal status No keypad lockout or 7 0 Factory default setting alarm factory default Keypad Lockout 7 1 4F
7. LOCASTATE LS S100 LS N100 Standalone Keypad Access Control User Manual Please read the manual carefully before use this unit 1 Packing List Name Quantity Remarks Keypad 1 User manual 1 Screw driver 1 20mmx60mm Special for keypad Rubber plug 2 6mmx30 mm used for fixing Self tapping screws 2 4mmxz28 mm used for fixing Star screws 1 O3mmx6mm used for fixing Please ensure that all the above contents are correct If any are missing please notify the supplier of the unit 2 Quick Reference Programming Guide To enter the programming mode Master code 999999 is the default factory master code To exit from the programming mode Note that to undertake the following programming the master user must be logged in To change the master code 0 New code New code The master code can be 6 to 8 digits To add a PIN user 1 User ID number IPINI The ID number is any number between 1 amp 2000 The PIN is any four digits between 0000 amp 9999 with the exception of 1234 which is reserved Users can be added continuously without exiting programming mode To add a card user 1 Read Card Cards can be added continuously without exiting programming mode To delete a PIN or a card user
8. is by card only Set valid card and PIN users 3 1 4 Entry is by card and PIN together Set valid card or PIN users 3 2 Entry is by either card or PIN default To add a user in either card or PIN mode i e in the 8 2 mode Default setting To add a Pin user 1 User ID number PIN The ID number is any number between 1 amp 2000 The PIN is any four digits between 0000 amp 9999 with the exception of 1234 which is reserved Users can be added continuously without exiting programming mode as follows 1 User ID no 1 PIN User ID no 2 PIN To delete a PIN user 2 User ID number Users can be deleted continuously without exiting programming mode To change the PIN of a PIN user This step must be done out of ID number Old PIN New PIN New PIN programming mode To add a card user Method 1 1 Read card This is the fastest way to enter cards Cards can be added continuously without exiting user ID number auto generation programming mode To add a card user Method 2 1 ID numker Read card H This is the alternative way to enter cards User can be added continuously without exiting using User ID Allocation In this method a
9. ld key whilst powering the unit back up c On hearing two Di release key system is now back factory settings Please note only installer data is restored user data will not be affected 9 Anti Tamper Alarm The unit uses a LDR light dependent resistor as an anti tamper alarm If the keypad is removed from the cover then the tamper alarm will operate 10 Sound and Light indication Operation Status Red Light Green Light Yellow Light Buzzer Power on Bright Di Stand by Bright Press keypad Di Operation successful Bright Di Operation failed DiDiDi Enter into programming mode Bright In the programming mode Bright Di Exit from the programming Bright J Di mode Open the door Bright Di Alarm Bright Alarm 11 Detailed Programming Guide 11 1 User Settings To enter the programming mode Master code 999999 is the default factory master code To exit from the programming mode Note that to undertake the following programming the master user must be logged in To change the master code 0 New code HE HF New code The master code can be 6 to 8 digits long Setting the working mode Set valid card only users 3 0 Entry
10. llocate the card a PIN as follows is reserved z Read cardi 11234 PIN PIN To change a PIN in card and PIN mode Method 1 Note that this is done outside programming mode so the user can undertake this themselves Read Cardi Old PIN New PIN New PIN To change a PIN in card and PIN mode Method 2 Note that this is done outside programming mode so the user can undertake this themselves ID number Old PIN New PIN New PIN To delete a Card and PIN user just delete the card 2 UserID To add a card user in card mode 3 0 To Add and Delete a card user The operating is the same as adding and deleting a card user in 12 To delete All users To delete ALL users Note that this is a dangerous option so use with care 2 0000 To unlock the door For a PIN user Enter the PIN then press For a card User Read card For a card and PIN user Read cardi then enter PIN 11 2 Door Settings Relay Output Delay Time To set door relay strike time Master code H 4 0 99
Download Pdf Manuals
Related Search