Owner`s Manual Digital Recording Systems
Contents
1. Switch to Multi screen Call the Auto Pan function display Select an active Monitor Calla Preset NO N NO NO Cruise F i aan Open the Function Bar Call the Cruise function Up Down Left Right PTZ control of Motordome 30 Joystick Enter and Esc Cameras English Rear View 1 DC12V power port Power supply connection 2 RS 485 communication port Camera and or DVR connection RS485 WNWOO RS485 3 RS 232 communication port Firmware update or DVR connection _RS232 1 0 S N Definition S N Definition _ eae A ooo 6S S Se 3 2 RS232 T __ J7 6 3 RS232 R Z a S a 5 Communication Ground o Z o SS 5 2 System Setup The CCTV System Control Keyboard can connect and control various front end terminal equipment such as Motordome Cameras DVRs and Decoders via the RS 485 communication port You can access the operation and configuration functions of these by directly connecting them to the keyboard 5 3 Connection to a Motordome Camera Connect a Motordome Camera directly to the Keyboard by connecting the and of the RS 485 port with the corresponding and ports of the Motordome Camera Set both devices to the same protocol and baud rate RS485 Connection PELCO D Keyboard PTZ 6 English 5 4 Connection to a GRUNDIG DVR Connect a GRUNDIG Recorder directly to the Keyboard by connecting the and of the RS 485 port with2. The following table explains how to call and save functions of the Motordome Camera connected to a GRUNDIG DVR using the GRUNDIG Protocol Function Keys to press Enter the CAM mode Disable Enable the Keyboard Sound ID ID Select a Camera Enter the administrator mode ID 0On Password 123456 Leave the administrator mode D Off Auto Search for protocol amp baud rate Select a protocol manually Select a baud rate manually 12 English Function Keys to press Set Focus to Far Call a Preset Preset No Enter Preset No On Call a Sequence Call a Cruise Save a Cruise Move PTZ with Joystick to Start Position Cruise No On Move PTZ with Joystick to Pan Tilt and Zoom Cruise No Off Call an Autopan Auto Pan No Enter Save an Autopan Move PTZ with Joystick to Start Position Auto Pan No On Move PTZ with Joystick to End Position Auto Pan No Off English Note If you have the Motordome Camera connected directly to the Keyboard using the PELCO D protocol all of the functions of the above table will work only the functionalities in the table below are different Function Keys to press Select something in the PTZ OSD Leave the PTZ OSD Close 14 English Specifications GKB A0110M Serial Interface s Protocol Multi protocol camera 1x RS 232 1x RS 485 GRUNDIG proprietary Pelco D Pelco P Panasonic Samsung DM SonyD70 VCL MIKAMI CBC B01 B02 SonyD70_R
3. Humidity To clean the product gently wipe the outside with a clean dry cloth 3 This Product uses AC power of 110V 240V Be cautious not to cause electric damages to the product 4 Be careful not to drop the product Physical shocks may harm the product including the internal HDD In addition be sure the product is secured after installation 9 This Product is made of metal Therefore you can hurt human beings if you throw it to them or hit it on them When installing the product be cautious to locate it in safe places where children cannot reach it 6 If the product does not operate properly please contact the closest GRUNDIG distributor for after sales service Tampering or disassembling the product will cause expiration of the warranty 7 Security surveillance laws may differ for each country Therefore please contact the local region first to avoid any surveillance law violations 8 Experience and technical skills are needed for the installation of this product as an improper installation may cause fire electric shocks or defects Any installation job should be performed by the vendor you purchased this product from The content of this manual can differ according to firmware or software upgrading The standard and appearance of the products may be changed for the improvement of quality without prior notice 4 Package Contents These parts are included Keyboard Power supply Power cord Cleaning towel RS 232 connecto
4. the corresponding and ports of COM Port of the GRUNDIG DVR Set the serial settings of the corresponding COM port of the DVR to GKB A0110M or WKC 100 depending on the firmware Device o D k os Device Keyboard WKC100 Se Properties Interface R5232 R5485 E P l I i l l l Baud Rate 1200 3400 4800 9600 19200 38400 57600 115200 Framing Stop Bit 1 bit 2 bits Data Bit 7bits 8 bits Parity Bit None Even The Keyboard is already configured under DVR mode Motordome cameras that are connected to the DVR and configured in the DVR can be controlled by the keyboard too A ae St aS Sa a ARSE RS485 Connection RS232 RS485 PELCO D Connection Keyboard PTZ GRUNDIG Protocol Com2 Com3 Keyboard DVR Com1 Com2 Com3 GRUNDIG NOTE You can also use a RS232 cable to control the DVR Connect an appropriate cable to the connectors of the keyboard and the DVR and configure the COM1 port of the DVR as described above English 5 5 Connection to DVRs and Motordome Cameras It is also possible to connect several GRUNDIG DVRs and Motordome Cameras directly to the keyboard There will be no serial connection between the cameras and the DVRs but the PTZ control will be more fluent DVR ID 1 DVR ID 2 CAM ID CAM ID e E O Sema i aaa ee EEE i z Q goannas E R R R R RS232 RS485 Connection RS485 Connection GRUNDIG Protocol PE
5. 57600 115200 Baud Rate Framing Stop Bit 1 bit 2 bits Data Bit 7 bits 8 bits Parity Bit None Even Picture Default settings for the Keyboard in the DVR 6 DVR Control The System Keyboard can take over all the functions on the front panel or the On screen Menu of the DVR Therefore all the buttons that are named the same as a button on the front panel will execute the same functionality Please check the DVR manual for reference what these buttons do The Joystick will perform the Up Down Left amp Right functionality of the direction keys and can also execute the Esc and Enter button if you turn it counter or clockwise To select a DVR please enter the DVR mode by pressing the button DVR Then select the ID of the DVR by pressing ID then pressing the number and Enter in the end in the table ID No Enter The ID of the DVR can be changed in the system menu of the DVR under System gt Utilitiy gt Keyboard ID To select the Single Channel View press the dedicated number of the channel and then press Enter No Enter in the table for example 3 Enter for Channel 3 or 1 2 Enter for channel 12 English 7 If the Channel is a Motordome Camera you will directly access the Pan Tilt and Zoom functionality of the camera without switching to CAM mode To get access to more functionalities like loading presets and sequences you will need to switch to CAM mode by pressing the CAM button Fun
6. FOR A GOOD REASON GRUNDIG en Owner s Manual Digital Recording Systems GKB A0110M Keyboard with 3D joystick GKB A0110M 62 1 04 06 2012 ASP AG Content 4 Connection to a GRUNDIG DVR 5 Connection to DVRs and Motordomes 1 Introduction 6 Combined Connection Recommended 7 8 2 Key Features of the Keyboard 2 8 3 Important Safety Instructions 2 7 Camera Protocol Setup 8 4 Package Contents 2 8 DVR Protocol Setup 5 Installation 3 9 Keyboard Setup ina GRUNDIG DVR 7 1 Part Names and Functions 3 6 DVR Control 9 2 System Setup 7 Camera Control 12 6 3 Connection to a Motordome Camera 1 Introduction Before product installation and operation please become thoroughly familiar with this user manual and other manuals referenced by this manual This user manual the software and the hardware described here are protected by copyright law With the exception of copying for general use within fair use copying and reprinting the user manual either partially or in entirety or translating it into another language without the consent of ASP AG is strictly prohibited This specification may change without prior notice for improvement of product performance Product Warranty and Limits of Responsibility The manufacturer does not assume any responsibility concerning the sale of this product and does not delegate any right to any third party to take any responsibility on its behalf No warrant
7. GRUNDIG VC LILIN Baud Rate Control LCD Panel size Pan Tilt Control 1 200 19 200bps Up to 99 DVRs 2x16 Gray Graphic LCD Pan Left Right Tilt Up Down Lens Control Iris Close Open Focus Near Far Zoom Tele Wide DVR Control RW Stop Play FF Rec PTZ Menu Search Backup Monitors PTZ Control Auto PAN Preset Sequence and Cruise Function Support Humidity 20 70 RH Storage Temperature 40 C 70 C Operating Temperature 10 C 50 C Supply Voltage 12 VDC power adaptor included Power Consumption 1 5 W Weight 2 5 kg Dimensions wxhxd 299 x 94 x 188 5 mm Dimensions 188 5 English 15 EC Declaration of Conformity 4 GKB A0110M Keyboard with 3D joystick It is hereby certified that the products meet the standards in the following relevant provisions EC EMC Directive 2004 108 EC Low Voltage Directive 2006 95 EC Applied harmonised standards and technical specifications EN 59022 2003 EN 61000 6 2 2002 EN 61000 6 3 2002 EN 61000 4 2 2001 EN 61000 4 3 2003 EN 61000 4 4 2002 EN 61000 4 5 2001 EN 61000 4 6 2001 ASP AG L ttringhauser Str 9 42897 Remscheid Germany Remscheid 04 06 2012 Ludwig Bergschneider CEO English
8. LCO D Keyboard DVR Com1 Com2 Com3 Keyboard PTZ 5 6 Combined Connection Recommended Another option to connect the Keyboard to a DVR and a Motordome Camera would be to connect them all directly together using a triangle connection This will give you full control of the DVR and the Motordome while adding a slighty better performance under CAM mode using the PELCO D protocol of the camera 2 5 PRE REDRE RS485 Connection PELCO D RS232 RS485 Connection Keyboard DVR Com2 Com3 RS485 Connection GRUNDIG Protocol Keyboard PTZ Keyboard DVR Com1 Com2 Com3 5 7 Camera Protocol Setup If the Motordome Camera is connected to the DVR and not directly to the Keyboard you do not need to setup the protocol and baud rate The Keyboard will use the GRUNDIG protocol to send the commands to the DVR which will forward them to the Motordome Camera 8 English If you have the Motordome Camera connected directly to the Keyboard you will need to set up the protocol and the baud rate of the Motordome Camera in the keyboard To change the protocol of the CAM mode you will need to get administrator access to the keyboard first Press ID and afterwards ON then enter the admin password 123456 and press Enter afterwards Select the camera for which you want to change the protocol by pressing the Camera ID and Enter afterwards and change the protocol by pressing the key Protocol until the used protoco
9. ction Keys to press Enter the DVR mode DVR Disable Enable the Keyboard Sound ID ID Select a DVR ID No Enter ee Open the Search Menu Search Open the Lock Front Key Menu Activate dig Zoom single channel view Dig Zoom Activate a Relay Relay No Enter Deactivate a Relay Relay Relay No Enter Select a Channel Rewind Increase rewinding speed raus w 10 English Function Keys to press Forward Increase forwarding speed Stop Playback Go back to Live mode Enter the Playback mode Start Manual Recording English 7 Camera Control Under CAM mode you will be able to access more functions of the Motordome Camera depending of the protocol that is used in the Motordome Camera With GRUNDIG cameras and the PELCO D protocol you can load Presets Sequences Auto Pans and Cruises It is also possible to save Presets Auto Pans and Cruises Of course you can also access the OSD of the camera and do all the configuration of the Motordome Camera from remote If you switch from DVR mode to CAM mode the Keyboard will set the ID of the CAM mode camera to the last selected single channel view If you want to change the ID of the camera please press a number and Enter afterwards No Enter in the table for example 1 1 Enter to select the Camera with the ID 11 You can control the PTZ function with the 3D Joystick by moving it left right up amp down and turn the Joystick wheel counter and clockwise
10. l appears on the display then press Enter to confirm To adjust the baud rate press the Baudrate button until the used baud rate appears on the display Press Enter to confirm the selected baudrate You can also use the Search button to automatically search for the protocol and baud rate Follow the instructions on the display to find the correct protocol and baud rate Leave the administrator mode after you have set up the protocol and baud rate by pressing ID and Off afterwards 5 8 DVR Protocol Setup Under DVR mode the keyboard Is set automatically to the GRUNDIG proprietary DVR protocol that should work straight away If you need to change the protocol or baudrate of the DVR mode just enter the administrator mode the procedure is similar to the one for CAM mode 5 9 Keyboard Setup ina GRUNDIG DVR The Keyboard needs to be configured in the Main Menu of the DVR under Device gt Serial It can be configured for each Serial connection Com1 RS232 or Com2 and Com3 RS485 Just select the serial connection to which the keyboard is attached to and change the protocol to WKC100 or GKB A0110M depending on the firmware version Under default settings the baud rate is set to 9600 If you have changed the baudrate of the keyboard under DVR mode please adjust the DVR correspondingly Device 3 amp Device Keyboard WKC100 Properties InterFace R5232 R5485 I I I EL I I I I 1200 2400 4800 9600 19200 38400
11. r RS 485 connector Owner s manual 2 English 5 Installation 5 1 Part Names and Functions Top View os 3 4 om OS gogo English Z Key Function DVR Mode Function CAM Mode Open the Backup Backup dialogue Screenshot in None Pause Menu None Esc Clear Automatic search for the Open the Search dialog protocol of the Motordome Protocol Quick setting of CAM Quick setting of CAM DVR DVR protocol protocol Baudrate Quick setting of CAM Quick setting of CAM DVR DVR baud rate baud rate Locking front panel buttons of the DVR None Increase the aperture Open the dig Zoom Zoom in with the Tele dig Zoom Close Lock Reduce the aperture Motordome function Zoom out with the O None Motordome Activate the relay Manual focus function Open the PTZ control l Manual focus dialogue Near Relay 12 Far PTZ ow English z Function DVR Mode Function CAM Mode None Key DVR O DVR control mode Select CAM DVR ID Select CAM DVR ID CO Pause Playback Call the Aux function Start Playback Start Manual recording No O NS NO NO sO CO O1 ice NJ NO O NO NO gt x ON gt Es Run No O Start a Sequence Call the Sequence function O Ti Tl A Auto Pan Multi
12. y is offered for any attachments or parts not supplied by the manufacturer The product warranty does not cover cases of accidents negligence alteration misuse or abuse for example Malfunctions due to negligence by the user Deliberate disassembly and replacement by the user Connection of a power source other than a properly rated power source Malfunctions caused by natural disasters fire flood tidal wave etc This product is not for exclusive use of crime prevention but also for assistance in cases of fire We take no responsibility for damage from any incident Caution This equipment underwent EMC registration and is suitable for business purposes Distributors and users are aware of this point Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures English 1 2 Key Features of the Keyboard Full control over GRUNDIG Recorders of the GRH or GDV series and GRUNDIG Motordome Cameras of the GCA and GCH series Auto protocol search function for easy installation of Motordome Cameras Multiple protocols implemented Pelco D Pelco P Panasonic Sony Samsung etc 3 Important Safety Instructions 1 Do not place heavy objects on the top of the product 2 This Product is for indoor use It is not weatherproof Please use the product considering its environmental specifications Temperature amp
Download Pdf Manuals
Related Search