- Divelbiss Corporation
Contents
1. 1 800 245 2327 www divelbiss com Getting Started To install the ICM EBB XXX s kernel 1 Verify the target has been configured see Configuring the ICM EBB XXX Target in EZ LADDER Toolkit 2 Connect the Programming cable s from the computer to the ICM EBB XXX See Programming Port in the Features section 3 Create a small one rung program with a normally open direct contact and an output tied together You may also open a pre existing program for the EBB EZ LADDER version 1 0 4 4 and later includes a sub directory EZ LADDER Kernel Install Start Pro grams which has starter programs for each target to load the kernel Choose GetStarted ICM EBB 128K dld or GetStarted ICM EBB 256K dld based on the model number C 4 Click the Compile button 5 Click the button to change from the Edit to Monitor Mode m 6 Click the Connect button to connect to the target A dialog will appear automatically when no kernel is loaded If this dialog does not appear click PROJECT then BOOTLOADER 7 Click the BROWSE button and select the target s kernel by part number located by default at C Program Files EZ Ladder Kernel The following are kernel names and descriptions File Name Description To be Used on Partnumber EnhancedBabyBear_128k dat Kernel for 128K EBB ICM EBB 100 ICM EBB 200 ICM EBB 300 ICM EBB 400 ICM EBB 500 EnhancedBabyBear_256k dat Kernel f2. The transformer shown is optional The ICM EBB XXX is protected by a resetable fuse If the fuse should open the power LED is not illuminated remove the input power for 30 seconds and then reconnect the input power The fuse will automatically reset when the power is removed ICM EBB XXX User s Manual Document 2004007 9 pdf 9of 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com ICM EBB XXX Features TA Yellow Wire ON To Input Power Black Wires Yellow Wires on EBB To Input Power Yellow Wires EE 2 Green Wir _ 12VDC 120VAC 50 60Hz Green Wir Earth 22 AC SUPPLY WIRING METHOD Earth Ground DC SUPPLY WIRING METHOD Figure 2 2 Input Power Connections Input Power LED The ICM EBB XXX provides a visible status of the input power via the Input Power LED When illuminated the input power is ok Mounting amp Dimensions The ICM EBB XXX mounts to any sub plate using standard hardware including standoffs and screws See Figure 2 3 4 6 cms dm d ICM EBB XXX PROGRAMMIN PORT RS232 zl 0000 o 5 00000 T ICM EBB IO 54RE P 1 O Expander HHHEEEEHEEEEEE Figure 2 3 Mounting amp Dimensions ICM EBB XXX User s Manual Document 2004007 9 pdf PAGE 10 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown
3. EBB XXX User s Manual Document 2004007 9 pdf 16 of 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com ICM EBB XXX Features As one of the standard features of PLC on a Chip and EZ LADDER Toolkit the ICM EBB XXX supports the use EEPROM memory that may be used to store and recall boolean integer real and timer values in non volatile memory in the ladder diagram This can be used to store field adjustable set points and more The ICM EBB XXX supports 1768 Bytes of EEPROM memory Models 100 200 300 400 500 and 2792 bytes of EEPROM memory Models 600 700 This memory is accessed in the ladder diagram using the EEPROM_READ and EEPROM WRITE Function blocks The same variable type that writes to the EEPROM location should be used to read the EEPROM location A memory map is recom mended for organizing variables stored in EEPROM Each EEPROM address is absolute and is one byte in size Boolean variables fill two bytes while all other variable types fill four bytes of EEPROM When writing a boolean to address the actual variable will use addresses and 1 two bytes Should you write an integer variable into address O then it would use addresses 0 3 A memory map should be created and used to assign variable types and addresses prior to coding to ensure that variable size and types are accounted for Variable 1 Address Boolean 2 Variable
4. This is not a general purpose port and may not be used in any other capacity than programming the controller itself The Programming Port defaults to Baud 57600 Parity None Data Bits 8 Stop Bits 1 To program the ICM EBB XXX a null modem cable is required between the computer serial port and the controller s programming port This cable can be self made purchased locally or ordered from Divelbiss Use Divelbiss Part Number 126 102860 Figure 2 1 provides the Programming Port Pinout RS232 Programming Port Description Not Connected Receive Data Transmit Data Not Connected Signal Ground Not Connected Request To Send Clear To Send Not Connected 1 2 3 4 5 6 7 8 9 Figure 2 1 Programming Port Pin Out Watchdog LED Q The operating status of the ICM EBB XXX can be determined the by Watchdog LED When the Watchdog LED is flashing at a slow rate approximately once per second then there is no ladder program executing When the Watchdog LED is flashing at a fast rate approximately 10 times per second a program has been loaded and it is executing Should the Watchdog LED not flash at all first check the input power If the input power is correct and there is still no Watchdog LED contact Divelbiss Technical Services Input Power The ICM EBB XXX may be powered using 10VAC or 12VDC Apply power to CONN1 using the provided input power cable assembly PIMS CA 6 Refer to the input power schematic for details
5. 2 Address Integer 4 Variable 3 Address Boolean 2 bytes uses location 0 and 1 bytes uses location 2 3 4 and 5 bytes uses location 6 and 7 NT ojos 7 meae WoT ss Is Ts gt ATs _ Te wwweswwe 1 MEM Figure 2 15 EEPROM Memory Locations EEPROM storage area has a limited number of write cycles therefore it shouldn t be used to store data which changes often and must be re written often Writing often to the same location can cause the location to fail ICM EBB XXX User s Manual Document 2004007 9 pdf PAGE 17 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com ICM EBB XXX Features ICM EBB XXX Target Setting Options To use some of the function blocks and features on the ICM EBB XXX it may be required to configure additional target properties in the Project Settings Dialog Box Click PROJECT then SETTINGS With the Enhanced Baby Bear model selected click PROPERTIES The following are items that must be configured in the Enhanced Baby Bear Project Settings Properties Dialog J1939 Properties This is where SAE J1939 Communications is enabled and configured Refer to the J1939 section of the EZ LADDER Manual OptiCAN Properties This is where OptiCAN Communications is enabled and configured Refer to the OptiCAN section of the EZ LADDER Manual This is used if the Serial Print function block is to be
6. Ohio 43019 1 800 245 2327 www divelbiss com ICM EBB XXX Features The ICM EBB XXX includes 5 on board digital inputs They are identified in EZ LADDER Toolkit and this manual as DI1 03 through DI1 07 Each digital input can accept an input voltage of 10 30 VAC or DC The inputs may be wired as either sinking or sourcing and are wired through the provided terminal block TS1 See Figure 2 4 for typical wiring diagrams for sinking and sourcing inputs isolated both the and terminals for each must be connected for the input to operate properly For convenience terminals la beled V and C are provided These terminals are quick wiring points to wire devices to the inputs The V is approximately 12VDC while the C is the ground or common See Figure 2 6 The inputs are labeled on the printed circuit board as 0 4 representing DI1 03 through DI1 07 respectively As these inputs are To read a digital input status in a ladder diagram place and connect the appropriate contact for your needs The DIRECT CONTACT and INVERTED CONTACT functions are used to read digital inputs in the ladder diagram When placing the contact verify you select the correct input address DI1 03 DI1 07 from the provided drop down menu Depending upon the EZ LADDER version these variables may be created automatically 011 03 011 07 If not automatically created you must create them Refer to the EZ LADDER User s Manual Sourcing ACor DC Input AC
7. USER S MANUAL REVISION 9 A ERA erem y E er 3 TS E77 R13 2 M Et p 7 Ride m EMO M NUM TOA fom a AK TIM 2s OPE ES ae e a pli 82 678 24 er LE dr 3 Lo jei 79 ICM EBB XXX Enhanced Baby Bear Controller Covered Models ICM EBB 100 ICM EBB 400 ICM EBB 700 ICM EBB 200 ICM EBB 500 ICM EBB 300 ICM EBB 600 Divelbiss Corporation Toll Free 1 800 245 2327 IVa ISS 9778 Mt Gilead Road Web http www divelbiss com Fredericktown Ohio 43019 il i i CORPORATION Email sales divelbiss com 2004007 9 Table of Contents Manual Contents Getting Started How to Use this Manual 3 Configuring the ICM EBB XXX Target in EZ LADDER Toolkit 4 Loading the ICM EBB XXX Kernel 4 Getting to Know the ICM EBB XXX 6 ICM EBB XXX Features OSU VMI TET Watchdog LED M 9 InDUE smtp Input Power LED NTC 10 Mounting e DiMenSiOnS sesssssssssesesrerrsrererrseserrrsesesrereseseereresereeseseree 10 PIZO U een e E E E A SIME E ER 11 Digital OUDOT 12 Counter INpUt NETT 12 General Purpose Serial Port ccccccccescsescseceecccnseeeseeeceeeeeseeeseeeeees 13 Real Time CHOC T 15 CAN Networking POTTS siasicnsisicaccansniesresaaswsnediac
8. WKemelNEr Browse Target EnhancedBabyBear 256k Version 1033 Erase User Program Update Target 10 A dialog box will appear to show the status of the kernel installation This could take a couple of minutes to install 11 When the dialog windows close the installation is complete The Enhanced Baby Bear is ready to use and may be connected to and programs may be downloaded Q The Enhanced Baby Bear Serial Number is factory set and cannot be changed Getting to Know the ICM EBB XXX The ICM EBB XXX is available in multiple configurations based on the model number While many features are offered the actual supported features depends on the model number Figure 1 2 lists these features The ICM EBB XXX Controller is designed to provide powerful programmable features in an open board format Connections are made via terminal blocks and connectors Refer to Figure 1 3 as it illustrates the ICM EBB XXX ICM EBB XXX User s Manual Document 2004007 9 pdf PAGE 6of 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com Getting Started High Speed Counter Real Time 5 Inputs Serial Glock 5 Outputs Modbus Port Modbus Serial Option requires optional Serial Port Module specify RS232 RS422 or RS485 Refer to the Specifications Section for details on operating parameters for all fea
9. a cables The ICM HDIO XX boards are din rail mounted Their addressing is set via on board jumpers The High Density I O uses the same type of I O assignments as the Enhanced Baby Bear where either DI or DO for Digital Input or Digital Output the Page Number 0 7 and then actual I O point 00 15 The I O addressing for the ICM HDIO XX 1 0 are as follows Digital Inputs 010 00 010 15 011 00 011 07 are used on board the ICM EBB XX and are NOT valid 011 08 017 15 Digital Outputs DOO 00 000 15 DO1 00 DO1 07 are used on board the ICM EBB XX and are NOT valid DO1 08 DO7 15 Enhanced Baby Bear I O Expansion The ICM EBB 400 and ICM EBB 600 1 can be expanded with an additional 8 Inputs rated 10 32 VDC and 8 Relay Outputs using the ICM EBB IO 54RE P Baby Bear Expanders use the ICM EBB XXX s CONN8 The ICM EBB IO 54P connects directly to CONN8 and is mounted to the ICM EBB XXX stacking configuration The ICM EBB IO 54RE P is factory addressed and cannot be changed The Enhanced Baby Bear I O uses the same type of I O assignments as the Enhanced Baby Bear where either DI or DO for Digital Input or Digital Output the Page Number 1 and then actual I O point 08 15 The I O addressing for the ICM EBB IO 54P is always as follows Digital Inputs 011 08 011 15 Digital Outputs DO1 08 DO1 15 For mounting the Enhanced Baby Bear with a stacking I O Expander please see the Mounting and Dimensions section this manual ICM
10. arately Type Open Board Storage Temperature 40 60 C ICM EBB XXX User s Manual PAGE 18 of 18 Document 2004007 9 pdf Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com
11. asventesnadveceateaaatinaverdeavess 15 OcExpallisl Oi 15 BPR IV MONO TT E UU TUUM 17 ICM EBB XXX Target Setting Options eere 18 SOC IT Ca 85 18 WARNING The ICM EBB XXX as with other programmable controllers must not be used alone in applications which could be hazardous to personnel in the event of failure of this device Precautions must be taken by the user to provide mechanical and or electrical safeguards external to this device This device is NOT APPROVED for domestic or human medical use ICM EBB XXX User s Manual Document 2004007 9 pdf PAGE 10 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com Getting Started This section explains how to read this manual and understand the symbols and information that it contains To begin using your Enhanced Baby Bear Controller you will need to follow these steps e Install EZ LADDER Toolkit if not already installed not included e Configure the Enhanced Baby Bear Controller in the EZ LADDER Toolkit Project Settings e Using purchased or self made cables connect the Input Power and Programming Port e Write a ladder diagram program e Download and run the program on the Enhanced Baby Bear Controller Refer to the appropriate sections of this manual for details on the above items Getting Started In this manual the following conventions are used to distinguish e
12. lements of text BOLD Denotes labeling commands and literal portions of syntax that must appear exactly as shown italic Used for variables and placeholders that represent the type of text to be entered by the user SMALL CAPS Used to show key sequences or actual buttons such as OK where the user clicks the OK button In addition the following symbols appear periodically in the left margin to call the readers attention to specific details in the text Warns the reader of a potential danger or hazard associated with certain actions Q Appears when the text contains a tip that is especially useful Indicates the text contains information to which the reader should pay particularly close attention All Specifications and Information Subject to Change without Notice ICM EBB XXX User s Manual Document 2004007 9 pdf 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com m Getting Started Configuring the ICM EBB XXX Target in EZ LADDER Toolkit Before you can program and use the ICM EBB XXX Controller it must be configured as a target within the EZ LADDER Toolkit For help with installing or using EZ LADDER please refer to the EZ LADDER User s Manual 1 In EZ LADDER from the File Menu at the top click PROJECT then SETTINGS This will open the Project Settings Window Select Enhanced Baby Bear 128K or Enhanced Baby Bear 256K ba
13. n blocks The CAN ports should be wired according to established practices for CAN networks Figure 2 14 illustrates typical CAN Port con nections CAN DEVICE CAN DEVICE J1939 or OptiCAN J1939 or OptiCAN AN POR z OCL Typical Typical 120 120 _ Install Terminating Resistors at each end Shield Only Connect at one End Figure 2 14 Typical CAN Port Connections I O Expansion Certain models of the Enhanced Baby Bear Controller allow for I O Expansion using one of two methods Depending upon the model the controllers I O may be expanded using the Divelbiss High Density 1 0 product line cables and 1 0 cards or the En hanced Baby Bear I O Expansion The High Density I O products connect using a cable set to the controller and are DIN rail mounted The Enhanced Baby Bear 1 0 mounts to the controller in a stacking configuration ICM EBB XXX User s Manual Document 2004007 9 pdf 15 of 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com ICM EBB XXX Features High Density I O Expansion The ICM EBB 500 and ICM EBB 700 1 0 can be expanded with up to an additional 120 Inputs and 120 Outputs using the ICM HDIO XX series I O Expander boards The ICM HDIO XX series provides a wide range of input and output types and voltages High Density I O Expanders use the ICM EBB XXX s CONN6 for data and CONN3 for power These connections are made vi
14. or DC Figure 2 8 Output Terminations Counter Input The ICM EBB XXX provides an optional on board counter input model dependent This is an up counter input that can operate up to 100 KHz It is ideal for connecting pulse output devices such as flow meters and other sensors Figure 2 9 illustrates the counter input circuit Figure 2 10 illustrates a typical sourcing input device the device sources the voltage connected to the counter while Figure 2 11 illustrates a typical sinking input device the devices sinks the input to ground or com mon connected to the counter ICM EBB XXX User s Manual Document 2004007 9 pdf PAGE 12 of 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com ICM EBB XXX Features EBB COUNTER CIRCUIT Opto Coupler V Figure 2 9 Counter Input Circuit 12 24VDC 12 24VDC PULSE OUTPUT PULSE OUTPUT Figure 2 10 Sourcing Counter Input Figure 2 11 Sinking Counter Input vide a drop down menu to select channel 1 Refer to the EZ LADDER Toolkit User s Manual for details on the CNTRTMR and other Q To use the high speed counter you must use the CNTRMR function block This block when placed in the ladder diagram will pro function blocks The High Speed Counter is always Channel 1 General Purpose Serial Port The ICM EBB 600 and ICM EBB 700 support an optional second serial port COM 1 This serial p
15. or DC Device Sinking ACC or DC Input Device ACC or DC Figure 2 4 Typical Sinking Input Circuit Figure 2 5 Typical Sourcing Input Circuit pM cc T cs Fd mh Pel Figure 2 6 Input Terminations ICM EBB XXX User s Manual Document 2004007 9 pdf PAGE 110 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com ICM EBB XXX Features The ICM EBB XXX includes 5 on board digital outputs relay They are identified in the EZ LADDER Toolkit and this manual as DO1 03 DO1 07 These relay outputs are Form A SPST and Normally Open Commutating diodes or Metal Oxide Varistors MOVs should be installed on all output channels for noise immunity based on the voltage being used AC or DC See Figure 2 7 To control a digital output in a ladder diagram place and connect the appropriate coil for your needs The DIRECT COIL and INVERT ED COIL functions are used to control digital outputs in the ladder diagram When placing the coil verify you select the correct out put address DO1 03 DO1 07 from the provided drop down menu Depending upon the EZ LADDER version these variables may be created automatically 001 03 DIO 07 If not automatically created you must create them Refer to the EZ LADDER User s Manual All outputs connections are wired through the provided terminal block TS3 See Figure 2 8 AC or DC ACC
16. or 256K EBB ICM EBB 600 ICM EBB 700 29 Bootloader Current Target Settings Target EnhancedBabyBear 256k Version 1032 Bootloader Version 1007 Serial Number 00123456 Upload File FileName ad Open Jh EZ Ladder Auto Kernel Seach 1 Favorite Links Name Date modified 9 EnhancedBabyBear 128k dat EnhancedBabyBear 256k dat nC 1000 dat 9 HEC 1100 dat HEC 1200 dat Folders HEC 2000 dat Divelbiss Corporation HEC 4000 dat J AllianceWinForm2005 91CM MB 100 dat di Documents NE Desktop 5 dx Recent Places More Bootloader 9 PCS 1XX dat EZ Ladder Auto 9 PCS 2XX dat Ji data 9 PLCHIP M2 1280X dat Ji PLCHIP M2 2560X dat File EnhancedBabyBear 256k dat v EZ Ladder Update Files dai v aw ICM EBB XXX User s Manual Document 2004007 9 pdf PAGE 5 of 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com Getting Started 8 Click the OPEN button to finish the kernel selection Make sure the correct kernel is chosen 9 Click the UPDATE TARGET button to install the kernel uL Bootloader Bootloader Version Conall Upload File FileName C Program Files 86 Divelbiss Corporation NEZ Ladder Auto
17. ort is a general purpose serial port that supports serial printing This port may also be used to communicate to a Modbus Master Device the ICM EBB XXX is a Modbus Slave At this time the general purpose serial port is an output device only as there is no software support to read a serial input module plugs into and mounts to the ICM EBB XXX Controller For mounting the serial port module to the ICM EBB XXX controller Q This port may be factory ordered as ICM EBB RS232 RS232 ICM EBB RS422 RS422 or ICM EBB RS485 RS485 This serial port see Figure 2 12 For pin assignments refer to Figure 2 13 ICM EBB XXX User s Manual Document 2004007 9 pdf 13 of 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com ICM EBB XXX Features zu 28 T amp a gt a gt H Figure 2 12 General Purpose Serial Port Mounting RS232 Serial Port ICM EBB RS232 RS422 Serial Port ICM EBB RS422 Description Transmit Data Not Connected Not Connected Receive Data Ground Receive Data Not Connected Not Connected Transmit Data Description Not Connected Receive Data Transmit Data Not Connected Ground Not Connected Request to Send Clear to Send Not Connected I0 FN FE RS485 Serial Port ICM EBB RS485 Description Description Transmit Data Not Connected Not Connected N
18. ot Connected Not Connected Not Connected Not Connected Transmit Data Ground Figure 2 13 General Purpose Serial Port Pin Assignments ICM EBB XXX User s Manual Document 2004007 9 pdf 14 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 e www divelbiss com ICM EBB XXX Features Real Time Clock The ICM EBB XXX includes an optional Real Time Clock The real time clock after set provides Month Day Day of the Week Year Hour Minute and Second The real time clock maintains time when power is lost via lithium battery The life of the battery for the real time clock generally has years of life before replacement is needed Should the battery need to be replaced replace the battery with the same type and size as the original The battery is a Lithium Coin Cell Type BR2325 CAN Networking Ports A CAN port is provided for networking including SAE J1939 and the Divelbiss proprietary OptiCAN Network The on board CAN port is CAN O To use the ICM EBB XXX s CAN port as either SAE J1939 or OptiCAN it will be necessary to config ure certain parameters These parameters may be configured from the ICM EBB XXX Properties Window in the Project Settings As these settings vary greatly and are software based only please refer to the EZ LADDER Toolkit User s Manual for details on configur ing using and implementing CAN port networking including all relevant functio
19. sed on you actual model from the choices Refer to Figure 1 1 EZ Project Settings Target Version Options Divelbiss Corporation Harsh Environment PLC Divelbiss Corporation Harsh Environment PLC Divelbiss Corporation Harsh Environment PLC cro Bear PLC Divelbiss Corporation Micro Bear Controller o d 4 og on dar ame vm LI Port ICOM1 Baud Rate 5 600 Figure 1 1 Project Settings Window 2 Anew window will open Select the Model number of the Enhanced Baby Bear from the drop down menu Click OK This will close the Enhanced Baby Bear Properties dialog box 3 Click OK This will close the Project Settings Window saving the EBB Model selected as the target for this ladder diagram project Loading the Kernel THE ICM EBB XXX WILL NOT FUNCTION UNLESS THIS STEP KERNEL LOADING IS COMPLETED The kernel is the firmware for the controller and to provide greater flexibility and reliability Enhanced Baby Bear Controller ship ments are factory shipped without a kernel If this is a new unit from the factory it will be necessary to load the kernel before a ladder program be downloaded If the kernel is already loaded this step is not required To upgrade a kernel see the EZ LAD DER User s Manual ICM EBB XXX User s Manual Document 2004007 9 pdf PAGE 4 of 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019
20. tures Figure 1 2 ICM EBB XXX Features Battery Real Time Clock Input Power Optional Serial Port HDIO Port Digital Outputs 12VDC or 10VAC RS232 RS422 RS485 Power amp Data Relay SPST N O SCECH8 dd 5 8 wniHin A ZI 2 0055550000 O m _ em ec cet eet cee _ j 2 EBB I O Port 5 3 Power amp Data 7 amp 2 g E 2 1 BEES 010 LO 710 710 _ o g m Tele n i d o E PROGRAMMING PORT RS232 gt ro r 1 rey r 1 re B o 2 P i Be 4 ee 14 214 ee 214 ee 14 214 114 1147 p GBB o OOO 0O 9OO beoooeoeeoooo 2212 goor Program Port CAN PORT Digital Inputs RS232 Null Modem OptiCAN J1939 10 30 VAC VDC Power LED Watchdog LED High Speed Counter Input Power Status Indicator Up Count Figure 1 3 ICM EBB XXX ICM EBB XXX User s Manual Document 2004007 9 pdf PAGE 7 of 18 Divelbiss Corporation e 9778 Mt Gilead Road Fredericktown Ohio 43019 1 800 245 2327 www divelbiss com ICM EBB XXX Features This section explains the Enhanced Baby Bear Controller ICM EBB XXX hardware features options and information regarding EZ LADDER Toolkit for basic operation ICM EBB XXX Features Programming Port The ICM EBB XXX is programmed using its Programming Port 0 This RS232 serial port is only to be used for programming using Divelbiss EZ LADDER Toolkit software
21. used to transmit data to an external device using the General Purpose Serial port The serial port is configured here Serial Print Properties Specifications Processor PLC on a Chip Memory 128K 256K Flash 8K 12K RAM 1768 Bytes 2792 Bytes EEPROM Model Dependent Serial Ports 1 Programming Port 1 Optional Multipurpose Port RS232 RS422 or RS485 Sold Separately Supports Modbus Slave Networking 1 CAN Port for Divelbiss OptiCAN or J1939 Communications Digital Inputs 5 Inputs rated 10 30 VAC VDC Optically Isolated with Indicator LEDs Typical Turn On 4 5 VAC VDC Typical Turn Off 3 5 VAC VDC Typical Input Current 9mA 9 30VAC VDC Digital Inputs 5 Relay Outputs Normally Open Dry Contacts with Indicator LEDs Relay Ratings 1 8HP 125VAC 250VAC 5A 30VDC 250VAC Counters 1 High Speed Counter Channel Count Up Optically Isolated 100KHz Max Frequency I O Expansion Input Power Operating Temp Program Language Real Time Clock Up to 120 total Inputs amp 120 total Outputs using High Density I O Line or 12 total Inputs amp 12 total Outputs using Enhanced Baby Bear I O Expansion 10VAC or 12VDC 115VAC with Optional Transformer 40 60 C Ladder Logic using Divelbiss EZ LADDER Toolkit Optional Moth Day Year Day of Wee Hour Minute Second Battery Type Lithium Coin BR2325 3VDC Dimensions 4 00 Wide x 8 75 Length x 1 04 Tall Mounting Panel Mount requires standoffs or other hardware Sold Sep
Download Pdf Manuals
Related Search