Enterprise PoE IP Phone VIP
Contents
1. Outside IP Set the outside Wan port IP address of DMZ Inside IP Set the inside LAN port IP address of DMZ Click the Add button to add new table click the Delete button to delete the selected mapping table Notice 10M 100M adaptive means the network card and other equipment physical consultations speed testing speed under bridge mode near to 100M in order to ensure the quality of voice and communications real time performance we made some sacrifices of NAT under the transmission performance Transmit with full capability only when system is idle so can not guarantee that the transmission speed reach to 100M VPN Config This web page provides us a safe connect mode by which we can make remote access to enterprise inner network from public network That is to say you can set it to connect public networks in different areas into inner network via a special tunnel Physical Network SECURITY Bomar emter MOST nat ve VPN IP VPN Mode UDP Tunnel C Enable VPN UDP Tunnel VPN Server addr 00 00 VPN Server Port o Server Group ID VPN Server Area Code 12345 VPN Configuration Field name explanation VPN IP Shows the current VPN IP address VPN Mode UDP Tunnel O L2TP CO Enable PN Select UDP Tunnel VPN Tunnel or VPN L2TP You can choose only one for current state After you select it you d better save configuration and reboot your phone Enable VPN Select it or not to enable or disable2. PLANET Networking amp Communication e Enterprise PoE IP Phone VIP 360PT User s manual Version 1 0 0 Copyright Copyright C 2010 PLANET Technology Corp All rights reserved The products and programs described in this User s Manual are licensed products of PLANET Technology This User s Manual contains proprietary information protected by copyright and this User s Manual and all accompanying hardware software and documentation are copyrighted No part of this User s Manual may be copied photocopied reproduced translated or reduced to any electronic medium or machine readable form by any means by electronic or mechanical Including photocopying recording or information storage and retrieval systems for any purpose other than the purchaser s personal use and without the prior express written permission of PLANET Technology Disclaimer PLANET Technology does not warrant that the hardware will work properly in all environments and applications and makes no warranty and representation either implied or expressed with respect to the quality performance merchantability or fitness for a particular purpose PLANET has made every effort to ensure that this User s Manual is accurate PLANET disclaims liability for any inaccuracies or omissions that may have occurred Information in this User s Manual is subject to change without notice and does not represent a commitment on the part of PLANET PLANET a
3. MMI Filter Table Start IP MMI Filter IP Table list MMI Filter Table Set Start IP 000 jerde A ad Add or delete the IP address segments that access to the phone Set initial IP address in the Start IP column Set end IP address in the End IP column and click Add to add this IP segment You can also click Delete to delete the selected IP segment MMI Filter Select it or not to enable or disable MMI Filter Click Apply to make it effective Notice Do not set your visiting IP outside the MMI filter range otherwise you can not login through the web Firewall SECURITY nat ven Firewall Type M access Enable C Out access Enable Firewall Input Rule Table Index Deny Permitprotocolsrcaddr Srcmask pes adar Hrewall Output Rule Table o deny Temp 192 168 1 14 255 255 255 0 192 168 1 118 255 255 255 0 Firewall Set Protocole uoe v frems OOO Rule Delete Firewall Configuration In this web interface you can set up firewall to prevent unauthorized Internet users from accessing private networks connected to the Internet input rule or prevent unauthorized private network devices from accessing the Internet output rule Firewall supports two types of rules input access rule and output access rule Each type supports at most 10 items Through this web page you could set up and enable disable firewall with input output rules System could prevent unauthorized access or access other networ
4. and then you can not dial out any phone number whose prefix is 001 X and are wildcard The x means matching any single digit for example 4xxx expresses any number with prefix 4 which length is 4 will be forbidden to dialed out The DOT means matching any arbitrary number digit for example 6 expresses any number with prefix 6 will be forbidden to dialed out Notice Black List and Limit List can record at most10 items respectively Digital Map Configuration This system supports 4 dial modes 1 End with dial your desired number and then press 2 Fixed Length the phone will intersect the number according to your specified length 3 Time Out After you stop dialing and waiting time out system will send the number collected 4 User defined you can customize digital map rules to make dialing more flexible It is realized by defining the prefix of phone number and number length of dialing In order to keep some users secondary dialing manner when dialing the external line with PBX phone can be added a special rule to realize it So user can dial a number as external line prefix and get the secondary dial tone to keep dial the external number After finishing dialing phone will send the prefix and external number totally to the server For example there is a rule 9 xxxxxxxx in the digital map table After dialing 9 phone will send the secondary dial tone user may keep going dialing After finish
5. VLAN IDs by setting signal voice VLAN and data VLAN The VLAN application of this phone is very flexible Do not use VLAN After switchboard recelved the Broadcast Frame transmit to every other port except the send port Switchboard Broadcast Frame Use VLAN After Switchboard received Switchboard the Broadcast Frame only transmit it to other e port which belong to same Pa VLAN with send port Y y F if d Broadcast Frame E g He nn gt Broadcast lt gt w Domain Ps Wigs Pa Chart 2 o a S pme Domain _ Az In chart 1 there is a layer 2 switches without setting VLAN Any broadcast frame will be transmitted to the other ports except the send port For example a broadcast information is sent out from port 1 then transmitted to port 2 3and 4 In chart 2 red and blue indicate two different VLANs in the switch and port 1 and port 2 belong to red VLAN port 3 and port 4 belong to blue VLAN If a broadcast frame is sent out from port 1 switch will transmit it to port 2 the other port in the red VLAN and not transmit it to port3 and port 4 in blue VLAN By this means VLAN divide the broadcast domain via restricting the range of broadcast frame transmission Note chart 2 use red and blue to identify the different VLAN but in practice VLAN uses different VLAN IDs to identify NETWORK MAN MES oos KEHAGA ES EA VLAN ID Check Enable Voice Data VLAN differentiated Un
6. of the crossed out wheeled bin symbol Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately Trademarks The PLANET logo is a trademark of PLANET Technology This documentation may refer to numerous hardware and software products by their trade names In most if not all cases their respective companies claim these designations as trademarks or registered trademarks Revision User s Manual for PLANET Enterprise PoE IP Phone Model VIP 360PT Rev 1 0 2010 Auguest Part No EM VIP360PT TABLE OF CONTENTS Cpap pter T IMM OCUC HOR aerie aio 6 VV MU O OR A A aa MA Aaa la 6 O A 6 _ _ _ RR de steak Silt Ate Sls sek st ok sie Sal he ah 7 PACK AGS CON aa ala ai ikka laiast T ENysical Detalla a dal ele a tel oleh Sieh otal A T Chapter 2 System Setup and Basic Operating rsnennenennnne annan 10 System Connguratlons TOF CECD y WED circa 10 ee 10 eee 14 eee 17 Chapter 3 SIP Service Configurations occccccccccconnncccnnnccnnnnonocnnonncnononenononenononenonono 31 Configuring SIP setting for IP Phone cooccoococcconcnconcconocononononanonncconononononenanconccanonos 31 _ E ee A AAA E MAA MA AA 31 SIPC ONO o m0 A A eet TU 33 IAX2 CONIO ucuncdniciiniionicio eiii ibas 36 IAX 2 O O o doo 36 UNO dad 37 DIAL PEER Std iia as 38 M a isaks taal otata E kal ESO OOO E laadal aada kena eset 42 DSP CONO sass ces ed ee edad laial 42 Call Se
7. out of band DTMF Relay RFC 2833 and SIP INFO e Three way Conference Caller ID Speed Dial e Call Hold Mute Forward Transfer Waiting Voice processing VAD CNG AEC Adaptive Jitter Buffer Management Package Content The contents of your product should contain the following items Enterprise PoE IP Phone VIP 360PT unit Power Adapter Quick Installation Guide CD ROM containing the user s manual Phone Stand RJ 45 cable Physical Details The following figure illustrates the front rear panel of IP Phone Hook switch LCD screen Soft Function key Speaker E Additional Service button OOO RLS Menu Handset Voice Mail OS Roid DOC Mite Mic Handset connector Dial button Navigation key SIP Line key Keypad Description 1 2 O O N O OI 11 12 13 14 15 16 17 18 19 Digit character map table 7 ABC A LCD Display SIP Line Key Soft button Memory Key PBook R Send Speaker Vol Vol Up Down Left Right OK Hold Mute Key Transfer RLS Envelop Menu and all status shall be displayed for users To make 3 line accounts dial call by pressing the Line1 Line 3 To control SMS SDial Memo etc function button Users could store their commonly used number in these keys and call them as speed dial Access the phonebook Redial the last dialed number Access redial menu Enable user to use the phone without handset Cycle through the phone menu Adjusting Volume loude
8. web browse port the defaultis 80 port if you want to enhance system safety vou d better change itinto non 80 standard port Example The IP address is 192 168 1 70 and the port value is 8090 the accessing address is http 192 168 1 70 8090 Telnet Port Set Telnet Port the default is 23 You can change the value into others Example The IP address is 192 168 1 70 the telnet port value is 8023 the accessing address is telnet 192 168 1 70 8023 RTP Initial Port Set the RTP Initial Port It is dynamic allocation RTP Port Quantity Set the maximum quantity of RTP Port the default is 200 Notice 1 You need save the configuration and reboot the phone after set this page 2 If you modify the port of Telnet and HTTP you would better set the value more than 1024 because the port value less than 1024 is system port reserved 3 if you set 0 for the HTTP port it will disable HTTP service DHCP SERVER NETWORK RS KESE KS EE pace server RE Cis DHCP Leased Table DHCP Lease Table lan 192 168 10 1 192 168 10 30 1440 255 255 255 0 192 168 10 1 192 168 10 1 DHCP Lease Table Setting DHCP Lease Table Delete DNS relay Setting DHCP SERVER Field name explanation DHCP Leased IP MAC mapping table If the LAN port of the phone connects to a device this Table table will show the IP and MAC address of this device DHCP Lease Table lan 192 168 10 1 192 168 10 20 1440 255 255 255 0 192 168 10 1 192 168 10 1 Shows the DH
9. Ban Anonymous Call Forward Type Forward Phone Number Server Type DTMF Mode RFC Protocol Edition For the phone supports the transfer of certain special features server set interval time between sending bye and hanging up after the phone transfers a call Enable the option the phone will receive the notify from the server Enable Disable Keep Authentication System will take the last authentication field which is passed the authentication by server to the request packet It will decrease the server s repeat authorization work if it is enable Enable Disable keeps NAT of SIP alive If some server refuse to register with too short interval time and has no packets sending to device in private network to keep NAT alive user could set this function ON It need set the keep alive interval time less than the NAT server s Enable Disable system to support RFC3581 Via rport is special way to realize SIP NAT Enable or disable SIP PRACK function suggest use the default config Set more parameters in contact field connection with SEM server Convert to 23 when send the URI Set call out by proxy without registration Set to ban Anonymous Call Select call forward mode the default is Off Off Close down calling forward Busy If the phone is busy incoming calls will be forwarded to the appointed phone No answer If there is no answer incoming calls will be forwarded to the appointed phone Always Incoming call
10. CP Lease Table the unit of Lease time is Minute Lease Table Name Specify the name of the lease table Start IP Set the start IP address of the lease table End IP Set the end IP address of the lease table the network device connected to LAN port will get IP address between Start IP and End IP by DHCP Netmask Set the Netmask of the lease table Gateway Set the Gateway of the lease table Lease Time Set the Lease Time of the lease table DNS Set the default DNS server IP of the lease table Click the Add button to submit and add this lease table DHCP Lease Table Delete Lease Table Name Select name of lease table click the Delete button will delete the selected lease table from DHCP lease table DNS Relay Select DNS Relay the default is enabled Click the Apply button to become effective Notice 1 The size of lease table can not be larger than the quantity of C network IP address We recommend you to use the default lease table and not modify it 2 If you modifies the DHCP lease table you need save the configuration and reboot SNTP Setting time zone and SNTP Simple Network Time Protocol server according to your location you can also manually adjust date and time in this web page NETWORK OO KESA Mees Eile IEEE SNTP 00 SNTP Time Set gg 00 Beijing Chongging Hong Kong Urumqi peon fe mo O a 2 wie ZN 3 7 5 A Wn al Daylight Timeset ji JE o zl D TEE JA
11. E lu ols sig RS ME 2 5 ee E J Ti Manual Timeset APPLY SNTP Field name explanation Server Set SNTP Server IP address Time Zone Select the Time zone according to your location Time Out Set the time out the default is 60 seconds 12 Hours Switch the time mechanism between 12 hours and 24 hours Systems Default is 24 hours mode SNTP Select the SNTP and click Apply to make the SNTP Times effective Enable Daylight Enable daylight saving time Time Setup the variety length shift minutes Month Setup stat and end month Week Setup start and end week Day Setup start and end day Hour Setup start and end hours Minute Setup start and end minutes APPLY Notice You need specify the above all items Chapter 3 SIP Service Configurations Configuring SIP setting for IP Phone SIP is a request response protocol dealing with requests from clients and responses from servers Participants are identified by SIP URLs Requests can be sent through any transport protocol SIP determines the end system to be used for the session the communication media and media parameters and the called party s desire to engage in the communication Once these are assured SIP establishes call parameters at either end of the communication and handles call transfer and termination SIP Config Set your SIP server in the following interface Prony Server address Prony Server Port SS proxy Userna
12. F SIP Info Security 802 1p QoS 802 1q VLAN Features Call Features Caller ID display Address Book 500 Missed Calls 100 Received Calls 100 Placed Calls 100 Date Time Display Speed dial configuration Network and Configuration Internet Connection Type Management Dimension W x D x H Operating Environment Power Requirement EMC EMI Network Setting Time Zone Setting SIP port configurable RTP port configurable Call Forward Call Waiting Call Transfer Call Hold 3 way Conference Black list for reject authenticated call White list Limit call No disturb Caller ID CLIR reject the anonymous call CLIP make a call with anonymous Support SMS Support Memo Alarm clock XML Configuration Fixed IP DHCP PPPoE LCD Keypad UI Web HTTP Remote Software Upgrade TFP FTP Auto Provision TFTP 295 x 205 x 75 mm 0 45 Degree C 0 65 humidity 5 VDC CE FCC
13. File Name ype Protocol Field name Web Update Server Username Password File name Application update FIP Update explanation Click the browse button find out the config file saved before or provided by manufacturer download it to the phone directly press Update to save You can also update downloaded update file logo picture ring mmiset file by web Set the FTP TFTP server address for download upload The address can be IP address or Domain name with subdirectory Set the FTP server Username for download upload Set the FTP server password for download upload Set the name of update file or config file The default name is the MAC of the phone such as 000102030405 Notice You can modify the exported config file And you can also download config file which includes several modules that need to be imported For example you can download a config file just keep with SIP module After reboot other modules of system still use previous setting and are not lost Type Protocol Action type that system want to execute 1 Application update download system update file 2 Config file export Upload the config file to FTP TFTP server name and save it 3 Config fie import Download the config file to phone from FTP TFTP server The configuration will be effective after the phone is reset Select FTP TFTP server Account Config You can add or delete user account and change the authority
14. P Set Syslog server IP address Server Port Set Syslog server port MGR Log Level Set the level of MGR log SIP Log Level Set the level of SIP log IAX2 Log Level Set the level of IAX2 log Enable Syslog Select it or not to enable or disable syslog Config Setting MAINTENANCE Pa Macri CONFIG KN Kee Museen 2 22 si Save Configuration Press the Save button to save the configuration files Backup Configuration Save all Network and VoIP settings Right Click here to Save as Config File txt Clear Configuration Press the Clear button to Clear the configuration files Config Setting Field name explanation Save Config You can save all changes of configurations Click the Save button all changes of configuration will be saved and be effective immediately Backup Config Right clicks on Right click here and select Save Target As then you will save the config file in txt format Clear Config User can restore factory default configuration and reboot the phone If you login as Admin the phone will reset all configurations and restore factory default if you login as Guest the phone will reset all configurations except for VoIP accounts SIP1 2 and IAX2 and version number Update You can update your configuration with your config file in this web page MAINTENANCE AUTO provision systoc conrrc UPDATE sccounr rcsooT Ol Web Update FTP Update Username Password
15. VPN UDP Tunnel VPN Server Addr 0 0 0 0 VPN Server Port BA Server Group ID VPN Server Area Code 12345 VPN Server Addr Set VPN Server IP Address VPN Server Port Set VPN Server Port L2TP VPN Server Addr Set VPN L2TP Server IP address VPN User Name Set User Name access to VPN L2TP Server VPN Password Set Password access to VPN L2TP Server System Logout Press the Logout button to Logout Phone Logout Click Logout and you will exit web page If you want to enter it next time you need input user name and password again Appendix A VIP 360PT Specifications Product Enterprise PoE IP Phone Model VIP 360PT Hardware AN 1 x 10 100 Base TX RJ 45 port 802 3af support Display LCD with backlight Function Keys 3 x Line Buttons Yellow LED 6 x Memory Key 3 x Soft Buttons Navigation Buttons 2 x Volume Buttons 8 x Fixed Function Buttons Phone Book RLS Envelope LED inside Hold MUTE Transfer Redial Speaker Protocols and Standard Standard SIP 2 0 RFC 3261 RTP RFC 2833 STUN RFC 3481 SNTP RFC 2030 TCP IP UDP HTTP TELNET DNS G 711 A law u law G 729 A B G 723 1 G 722 G 726 Voice Standard Auto negotiation Acoustic echo cancellation for integrated speakerphone operations Voice activity detection Silence suppression Comfort noise generation Dynamic Jitter buffer Call Progress Tone Generation DTMF Support In band Out of band DTMF RFC 2833 Out of band DTM
16. ange to Static mode Press button the screen shows Static the screen shows the IP address and gateway which were set just now if the phone could display the right time it shows that Static IP mode takes effect Network Mode Static IP 192 168 0 36 GW 192 168 0 1 Network Setup PPPoE By using PPPoE you don t have to setup IP address by yourself Instead an IP address will be issued to your IP phone by internet service provider automatically which is more convenient To complete your network setup using PPPoE please follow instructions described in this chapter 1 Get PPPoE account and password first 2 Ad button on IP Phone System Config Menu User Config Network 3 Press 4 a key until Network is selected then press OK or Soft2 Enter key Menu system Config User Config Network LCD screen will display WAN Network 4 Press OK or Soft2 Enter then choose PPPoE Net Mode Static DHCP lt gt PPPoE 5 Press Soft1 Edit the screen will display Account The screen will show the current account information Press Soft1 Del to delete it then input your PPPoE account and press Soft2 Save With saved displayed screen will jump to password settings PPPoE Set Account User123 PPPoE Set Password kkkkkkkkkkk 6 Press Soft2 Del again then input your PPPoE password and press Soft2 OK With Saved display
17. b s or 6 3kb s is available Set up the ring by default Select Signal Standard Select it or not to enable or disable VAD If enable VAD G729 Payload length could not be set over 20ms Call Service In this web page you can configure Hotline Call Transfer Call Waiting 3 Ways Call Black List white list Limit List and so on PHONE ee caL SERVICE MA RT Muesli eam 0 Call Service Setting No Answer ime 20 seconds Enable Call Transfer Enable Three Way Call Black List cay fe O 0 00 A per Call Service Field name explanation Hotline Specify Hotline number If you set the number you can not dial any other numbers No Answer Time Specify No Answer Time P2P IP Prefix Set Prefix in peer to peer IP call For example what you want to dial is 192 168 1 119 If you define P2P IP Prefix as 192 168 1 you dial only 119 to reach 192 168 1 119 Default is If there is no Set it means to disable dialing IP Remote Record No Set Remote Record number Via dialing this number you can hear all voice records in your VolP server Do Not Disturb Select NO Disturb the phone will reject any incoming call the callers will be reminded by busy but any outgoing call from the phone will work well Ban Outgoing If you select Ban Outgoing to enable it and you can not dial out any number Enable Call Transfer Enable Call Transfer by selecting it Enable Call Waiting Enable Call Waiting by selecting it Enable T
18. ber for each memory key After set it you can dial the number you set by pressing this memory key Key event function mode Remark You can set speed dial function by Memory Key mode For example you need set speed dial 8000 via sip 1 Select memory key in F4 s function key type then fill 3000 1 f in the corresponding right table You can set shortcut key of pbook redial DND MWI call forward or callers by Key Event mode in function key type Select key event in function key type then fill F_ PBOOK F_REDIAL F_DND F_MWI F_CFWD or F_CALLERS in the corresponding right table For example Maintenance Auto Provision MAINTENANCE AUTO PROVISION EEGI Mea KO Me eeet Kia Auto Update Setting a 3 m on i l D Ll El hd Field name Current Config Version Server Address Username Password Config File Name Config Encrypt Key Protocol Type Update Interval Time Update Mode a Auto Provision explanation Show the current config file s version Set FTP TFTP HTTP server IP address for auto update The address can be IP address or Domain name with subdirectory Set FTP server Username System will use anonymous if username keep blank Set FTP server Password Set configuration file s name which need to update System will use MAC as config file name if config file name keep blank For example 000102030405 Input the Encrypt Key if the configuration
19. d IP address Your need input new IP address in the address column to logon in the phone 3 If networks ID which is DHCP server distributed is same as network ID which is used by LAN of system system will use the DHCP IP to set WAN and modify LAN s networks ID for example system will change LAN IP from 192 168 10 1 to 192 168 11 1 when system uses DHCP client to get IP in startup If system uses DHCP client to get IP in running status and network ID is also same as LAN s system will refuse to accept the IP to configure WAN So WAN s active IP will be 0 0 0 0 LAN Config NETWORK E wan on ii EHA Bee E LAN Setting DHCP Service Bridge Mode LAN Config LAN IP Specify LAN static IP Netmask Specify LAN Netmask DHCP Service Select the DHCP server of LAN port or not After you modify the LAN IP address phone will amend and adjust the DHCP Lease Table and save the result amended automatically according to the IP address and Netmask You need restart the phone and the DHCP server setting will take effect NAT Select NAT or not Bridge Mode Select Bridge Mode or not If you select Bridge Mode the phone will no longer set IP address for LAN physical port LAN and WAN will join in the same network Click Apply the phone will reboot Notice If you choose the bridge mode the LAN configuration will be disabled Qos Config The VOIP phone support 802 1Q P protocol and DiffServ configuration VLAN functionality can use different
20. differentiated Y QoS Configuration Field name explanation VLAN Enable Before select it to enable VLAN you need enable Bridge mode in LAN config VLAN ID Check Enable Enable VLAN ID check by selecting it After enable VLAN ID check if VLAN ID of a data package is not the same with the phones or a data package do not have VLAN ID the data package will be discarded Voice Data VLAN After enable VLAN system will set packets with different type of VLAN ID differentiated Undifferentiated means after using VLAN both VoIP packets and other data packets will use the voice VLAN ID tag differentiated means after using VLAN VolP signal and voice packets will add voice VLAN ID and other data packets will add data VLAN ID data untagged means after using VLAN only VoIP packets will add voice VLAN ID Other data packets will not use VLAN DiffServ Enable Select it or not to Enable or disable DiffServ DiffServ Value Set DiffServ value the common value is 0x00 Voice 802 1P Priority Specify 802 1P Priority of voice signal data package Data 802 1P Priority Set 802 1p of data VLAN Non VolP data such as http telnet ping etc will use this value to set VLAN package Voice VLAN ID Set VLAN ID of voice signal data package Data VLAN ID Set 802 1q of data VLAN ID Non VolP data such as http telnet ping etc will use this value to set VLAN package Notice 1 Startup VLAN if set Voice Data VLAN differentiated as Undifferentiated all packets will u
21. e A PLANET NETWORK wan MEN MIT MESA KM E WAN Status BASIC NETWORK VOIP Current Gateway PHONE 20091119 WAN Setting MAINTENANCE SECURITY LOGOUT Obtain DNS server automatically 3 here you can choose connection mode static IP PPPoE or DHCP enter IP address for static IP mode and enter PPPoE username and password directly on web page If you want to enable VLAN function of PC and phone Ethernet port of this IP Phone you can also set it up here After you have entered the setting you need remember to click APPLY button located at the bottom of the web page PLANET NETWORK wan KE BE E Me i KAAN Menem 090 Active IP 192 168 0 109 Current Gateway 192 168 0 1 Get MAC Time BASIC NETWORK VOIP MAC Address 00 30 4F 00 6e 20 WAN Setting PHONE MAINTENANCE SECURITY LOGOUT WAN Config WAN Status MAC Address 00 30 4 00 60 20 Active IP The current IP address of the phone Current Netmask The current Netmask address MAC Address The current MAC address of the phone Current Gateway The current Gateway IP address Get MAC Time Shows the time of getting MAC address Static DHCP PPPOE O Please select the proper network mode according to the network condition VIP 360PT provides three different network settings Static If your ISP server provides you the static IP address please select this mode and then finish Static Mode setting If y
22. ed phone will call the number which starts with 9 actually the number sent out is 9 digit with 9 PHONE KSM KAMMI DIGITAL MAP Kit MT 00000 Oo faem eoo APPLY Digital Rule table Digital Map Configuration Field name explanation End with Set Enable Disable the phone ended with FF dial Fixed Length Specify the Fixed Length of phone ending with Time out Set the timeout of the last dial digit The call will be sent after timeout Digital Rule table Below is user defined digital map rule Specifies a range that will match digit May be a range a list of ranges separated by commas or a list of digits The x Match any single digit that is dialed The Match any arbitrary number of digits including none bh m II Tn Indicates an additional time out period before digits are sent of n seconds in length n is mandatory and can have a value of 0 to 9 seconds Tn must be the last 2 characters of a dial plan If Tn is not specified it is assumed to be TO by default on all dial plans 99118 74 Cause extensions 1000 8999 to be dialed immediately Cause 8 digit numbers started with 9 to be dialed immediately Cause 911 to be dialed immediately after it is entered Cause 99 to be dialed after 4 seconds Cause any number started with 9911 to be dialed 4 seconds after dialing ceases Notice End with Fixed Length Time out and Digital Map Table can be used simultan
23. ed screen will display the current password press soft2 OK to save the Account and password The screen will show Saved and then jump to show the current net mode Net Mode Static DHCP lt gt PPPoE RLS 7 Press KS Soft3 Quit thrice return to standby at this time the phone is trying to change to PPPoE mode Press 4 for checking the status If the screen shows Negotiating it shows that the phone is trying to access to the PPPoE Server if it shows an IP address then the phone has already get IP with PPPoE Network Mode PPPoE Negotiating Network Setup DHCP By using DHCP you don t have to setup IP address by yourself Instead an IP address will be issued to your IP phone by DHCP server on your local network automatically which is more convenient To complete your network setup using DHCP please follow instructions described in this chapter 1 Press button on IP Phone Menu System Config User Config Network 2 Press A a key until Network is selected then press OK or Soft2 Enter key Menu System Config User Config Network LCD screen will display WAN Network 3 Press OK or Soft2 Enter then choose DHCP Net Mode Static lt gt DHCP PPPoE 4 Press Soft2 Save with saved shown screen will jump to show the current net mode Net Mode Static lt gt DHCP PPPoE 9 Press CI Soft3 Auit
24. eously System will stop dialing and send number according to your set rules Phone Book You can input the name phone number and select ring type for each name here PHONE EA KOSE Marne PHONE BOOK MA S Phonebook Table Phone Book Field name explanation si Shows the detail of current phonebook Name Shows the name corresponding to the phone number Number Shows the phone number Ring Type Shows the ring type of the incoming call Click Modify to change the selected information and click the Delete to delete the selected record Notice the maximum capability of the phonebook is 500 items Function Key PHONE KM AMES KSG ESE eetet FUNCTION KEY Interface Configuration Contrast 5 o 19 Luminance fi 0 1 MWI Number NA Function Key Setting F_MWI ji I Function Key Field name explanation Contrast Set contrast of screen Luminance Set luminance of screen MWI Number To listening record in server we defined the function key F10 After you set it you can pick up or hands free and then press E to listen record in server Function Key Setting limit II Es memory y SSS koo mees OP EZ among y 000 Fe memory y SSS ES memory y SSS Line select SIP1 SIP2 SIP3 Dial peer or IAX2 in function key type After you set it you pick up handset or hands free press this function key and then you can use the corresponding IP line Memory Key you can set a num
25. fig LCD screen will display WAN User Config Network LCD screen will display WAN Network 3 Press OK or Soft2 Enter then choose Static Net Mode lt gt Static DHCP PPPoE 4 Press Soft1Edit and screen will show IP then press Soft1 Del to delete Input your IP address and press Soft2 Save to save what you input After Saved shown the screen will jump to show the Net mask information Static Set IP 192 168 0 36_ Static Set Netmask 255 255 255 0 5 Press Soft1 Del to delete Input your Net mask and press Soft2 Save After Saved shown the screen will jump to show the Gateway information Static Set Gateway 192 168 0 1 6 Press Soft1 Del to delete Input your gateway and press Soft2 Save After Saved shown the screen will jump to show the DNS information Static Set 7 Press Soft1 Del to delete Input your DNS server address and press Soft2 Save After Saved shown the screen will return to show IP information Static Set IP 192 168 0 36_ 8 Press Soft3 Quit once the screen shows Net Mode the cursor stay at lt gt Static with Soft2 Save pressed the screen shows Saved and then shows the current net mode Net Mode lt gt Static DHCP PPPoE RLS gt M np 0 9 Press CG Soft3 Quit thrice return to main interface and at this time the phone is trying to ch
26. file is encrypted Select the Protocol type FTP TFTP or HTTP Set update interval time unit is hour Different update modes 1 Disable means no update 2 Update after reboot means update after reboot 3 Update at time interval means periodic update Syslog Config Syslog is a protocol which is used to record the log messages with client server mechanism Syslog server receives the messages from clients and classifies them based on priority and type Then these messages will be written into log by some rules which administrator can configure This is a better way for log management 8 levels in debug information Level 0 emergency This is highest default debug info level You system can not work Level 1 alert Your system has deadly problem Level 2 critical Your system has serious problem Level 3 error The error will affect your system working Level 4 warning There are some potential dangers But your system can work Level 5 notice Your system works well in special condition but you need to check its working environment and parameter Level 6 info the daily debugging info Level 7 debug the lowest debug info Professional debugging info from R amp D person At present the lowest level of debug information send to Syslog is info debug level only can be displayed on telnet MAINTENANCE EE systos EMA iu E E O sd Syslog Set 51 Syslog Configuration Field name explanation Server I
27. hen you dial 1477 the SIP1 server will receive 1470011 Phone DSP Config In this page you can configure voice codec input output volume and so on PHONE psp MAME Marie cm Mure tee al Mittes nem DSP Configuration g711Ulaw64k Second Codec 4723 se g729 Fourth Codec o711Alaw64k First Codec Third Codec Fifth Codec Input Volume Handfree Volume 5 3 1 9 Output Volume 7 1 9 4 1 9 Ring Volume j 1 9 i w G72 Timestamps Default Ring Type Field name First Codec Second Codec Third Codec Forth Codec Fifth Codec Input Volume Hands free Volume G729 Payload Length Handdown Time Ring Type Output Volume Ring Volume G722 Timestamps G723 Bit Rate Default Ring Type Signal Standard VAD 160 20ms we G723 Bit Rate 6 3kb s v Type 1 Y E 0 DSP Configuration explanation The fist preferential DSP codec G 711A u G 722 G 723 G 729 The second preferential DSP codec G 711A u G 722 G 723 G 729 The third preferential DSP codec G 711A u G 722 G 723 G 729 The forth preferential DSP codec G 711A u G 722 G 723 G 729 The fifth preferential DSP codec G 711A u G 722 G 723 G 729 Specify Input MIC Volume grade Specify Hands free Volume grade Set 6729 Payload Length Specify the least reflection time of Handdown the default is 200ms Select Ring Type Specify Output receiver Volume grade Specify Ring Volume grade 160 20ms or 320 20ms is available 5 3k
28. hree Way Call Enable Three Way Call Accept Any Call If select it the phone will accept the call even if the called number is not belong to the phone Auto Answer If select it the phone will auto answer when there is an incoming call Use Record Server Select it or not to Enable or disable Use Record Server Auto handdown The phone will hang up and return to standby automatically at hands free mode Black List Set Add Delete Black list If user does not want to answer some phone calls add these phone numbers to the Black List and these calls will be rejected X and are wildcard The x means matching any single digit for example 4xxx expresses any number with prefix 4 which length is 4 will be forbidden to dialed out DOT means matching any arbitrary number digit For example 6 expresses any number with prefix 6 will be forbidden to dialed out If user wants to allow a number or a series of number incoming he may add the number s to the list as the white list rule the configuration rule is number for example 123456 or 1234xx Black List 4119 Means any incoming number is forbidden except for 4119 Note End with DOT when set up the white list Limit List Set Add Delete Limit List Please input the prefix of those phone numbers which you forbid the phone to dial out For example if you want to forbid those phones of 001 as prefix to be dialed out you need input 001 in the blank of limit list
29. ice provider Phone will not register if there is no phone number configured Set the display name Set proxy server IP address Usually Register SIP Server configuration is the same as Proxy SIP Server But if your VoIP service provider give different configurations between Register SIP Server and Proxy SIP Server you need make different settings Set your Proxy SIP server port Input your Proxy SIP server account Input your Proxy SIP server password Set the sip domain if needed otherwise this VoIP phone will use the Register server address as sip domain automatically Usually it is same with registered server and proxy server IP address Start to register or not by selecting it or not Set expire time of SIP server register default is 60 seconds If the register time of the server requested is longer or shorter than the expire time set the phone will change automatically the time into the time recommended by the server and register again Set examining interval of the server default is 60 seconds Set the user agent if have the default is VoIP Phone 1 0 Set the key for signal encryption Set the key for RTP encryption Set sip port of each line Set ring type of each line Set hot line number of each line Configure conference number in server conference Transfer Expire Time Enable subscribe Enable Keep Authentication NAT Keep Alive Enable Via rport Enable PRACK Long Contact Enable URI Convert Dial Without Register
30. ks set in rules for security Firewall is also called access list is a simple implementation of a Cisco like access list firewall It supports two access lists one for filtering input packets and the other for filtering output packets Each kind of list could be added 10 items We will give you an instance for your reference C In_access Enable Out access Enable Input Output Input v Sreadar fF Deny Permit Deny v Des add ff eny Y Field name explanation In access enable Select it to Enable in_ access rule out access enable Select itto Enable out_ access rule Input Output Specify current adding rule by selecting input rule or output rule Deny Permit Specify current adding rule by selecting Deny rule or Permit rule Protocol Type Filter protocol type You can select TCP UDP ICMP or IP Port Range Set the filter Port range Src Addr Set source address lt can be single IP address network address complete address 0 0 0 0 or network address similar to 0 Des Addr Set the destination address lt can be IP address network address complete address 0 0 0 0 or network address similar to Src Mask Set the source address mask For example 255 255 255 255 means just point to one host 255 255 255 0 means point to a network which network ID is C type Des Mask Set the destination address mask For example 255 255 255 255 means just point to one host 255 255 255 0 means point to a network which netwo
31. led numbers automatically 2 Specifies a range that will match digit It may be a range a list of ranges separated by commas or a list of digits lf user makes the above configuration after user dials 11 digit numbers started with from 135 to 139 the phone will send out 0 plus the dialed numbers automatically Use this phone you can realize dialing out via different lines without switch in web interface VOIP KSG rv MEA DIAL PEER Dial Peer Table 150 jenassamns soso se moaltas fno sutt fo a pooo foso fsm frevoro fosu f iaa Jooo Joso fsm faato fosati fo Add Dial Peer Destination optional Alias optional SIP gt Delete Length optional Dial Peer Option DIAL PEER Field name explanation Phone number There are two types of matching conditions one is full matching the other is prefix matching In the Full matching you need input your desired phone number in this blank and then you need dial the phone number to realize calling to what the phone number is mapped In the prefix matching you need input your desired prefix number and T then dial the prefix and a phone number to realize calling to what your prefix number is mapped The prefix number supports at most 30 digits Destination Port Alias Note There are four types of aliases Set Destination address This is optional config item If you want to set peer to peer call please input destination IP address or domain name If you want t
32. live Local SIP Port Set the SIP port Set Sip Line Enable Stun EEA Choose line to set info about SIP There are 3 lines to choose You can switch by Load button Use Stun Enable Disable SIP STUN Notice SIP STUN is used to realize SIP penetration to NAT If your phone configures STUN Server IP and Port default is 3478 and enable SIP Stun you can use the ordinary SIP Server to realize penetration to NAT DIAL PEER setting This functionality offers you more flexible dial rule you can refer to the following content to know how to use this dial rule When you want to dial an IP address the entry of IP addresses is very cumbersome but by this functionality you can set number 156 to replace 192 168 1 119 here rl When you want to dial a long distance call to Beijing you need dial an area code 010 before local phone number but you can also dial number 1 instead of 010 after we make a setting according to this dial rule For example you want to dial 01062213123 but you need dial only 162213123 to realize your long distance call after you make this setting 1T 1 0 0 0 0 5060 SIP rep 010 no suffix umber bestmaton Port pode amas Sum peltengt aa 000 foso SIP add fno sut 0 13 5 9 pocooooxx 0 0 0 0 5060 SIP add 0 no suffix o 1 x Match any single digit that is dialed lf user makes the above configuration after user dials 11 digit numbers started with 13 the phone will send out 0 plus the dia
33. me proxy Password SS Domain Realm S Enable Register O o Advanced Set Advanced SIP Setting Register Expire Time ET seconds MAT Keep Alive Interval 0 seconds Forward Phone Number ff Enable Conference number I O LS eurora Signal encode Rencode OO Enable Session Timer O Answer With Single codec O Auto Ter a RNE 7 oo 0 i User Agent Signal Key Media Key Local Port Ring Type Hot Line Number Conference Number Transfer Expire Time Enable Subscribe Enable Keep Authentication MAT Keep Alive Enable Via rport Enable PRACK Long Contact Enable URI Convert Dial Without Register Enable Strict Proxy Enable GRUU Ban Anonymous Call Enable DNS SRY Enable Displayname Quote IML SIP Config SIP Line Select SIP 1 Field name Register Status Server Name Server Address Server Port Account Name Password Phone Number Display Name Proxy Server Address Proxy Server Port Proxy Username Proxy Password Domain Realm Enable Register Register Expire Time NAT Keep Alive Interval User Agent Signal Key Media Key Local port Ring type Hot line Number Conference Number explanation Shows if the phone has been registered the SIP server or not or so show Unapplied Set the server name Input your SIP server address Set your SIP server port Input your SIP register account name Input your SIP register password Input the phone number assigned by your VoIP serv
34. o use this dial rule on SIP2 line you need input 255 255 255 255 or 0 0 0 2 in it SIP3 into 0 0 0 3 Set the Signal port the default is 5060 for SIP Set alias This is optional config item If you don t set Alias it will show 1 add xxx it means that you need dial xxx in front of phone number which will reduce dialing number length 2 all xxx it means that xxx will replace some phone number 3 del It means that phone will delete the number with length appointed 4 Rep It means that phone will replace the number with length and number appointed You can refer to the following examples of different alias application to know more how to use different aliases and this dial rule Call Mode Select different signal protocol SIP or IAX2 Suffix Set suffix this is optional config item It will show no suffix if you don t set it Delete Length Set delete length This is optional config item For example if the delete length is 3 the phone will delete the first 3 digits then send out the rest digits You can refer to examples of different alias application to know how to set delete length Examples of different alias application Set by web explanation example You need set phone number If you dial 93333 Destination Alias and Delete the SIP2 server Length will receive 3333 Phone number is XXXT Destination is 255 255 255 255 0 0 0 2 and Alias is del This means any phone No that sta
35. of each user account in this web page MAINTENANCE 155608 ESG Meat MU ACCOUNT K gi Set Keyboard Password User Set 77 ASK SKK guest Add User Account Option Account Configuration Field name explanation Keyboard Password Set the password for entering the setting menu of the phone by the phone s key board The password is digit User Name User Level mi a a This table shows the current user existed User Name Set account user name User Level Set user level Root user has the right to modify configuration General can only read Password Set the password Confirm Confirm the password Select the account and click the Modify to modify the selected account and click the Delete to delete the selected account General user only can add the user whose level is General Reboot MAINTENANCE MUSSO E KESA KU EM REBOOT Reboot Phone Press the Reboot button to reboot Phone If you modified some configurations which need the phone s reboot to be effective you need click the Reboot then the phone will reboot immediately Notice Before reboot you need confirm that you have saved all configurations MMI Filter SECURITY Tur MEGS AASS MMI Filter Table 192 168 1 15 192 168 1 20 Modify MMI Filter Table Set MMI Filter Table Set MMI Filter User could make some device own IP which is pre specified access to the MMI of the phone to config and manage the phone
36. ou don t know about parameters of Static Mode setting please ask your ISP for them DHCP In this mode you will get the information from the DHCP server automatically need not to input this information artificially PPPoE In this mode your must input your ADSL account and password Get DNS server automatically Select it to use DHCP mode to get DNS address if you don t select it you will use static DNS server The default is selecting it Static IP Address EEE O 36 Primary DNS no Alter DNS 202 96 128 68 If you use static mode you need set it IP Address Input the IP address distributed to you Netmask Input the Netmask distributed to you Gateway Input the Gateway address distributed to you DNS Domain Set DNS domain postfix When the domain which you input can not be parsed phone will automatically add this domain to the end of the domain which you input before and parse it again Primary DNS Input your primary DNS server address Alter DNS Input your hac ee DNS server address PPPOE Server Username Password If you uses PPPoE mode you need to make the above setting PPPoE Server It will be provided by ISP Username Input your ADSL account Password Input your ADSL password Notice 1 Click Apply button after finished your setting IP Phone will save the setting automatically and new setting will take effect 2 If you modify the IP address the web will not response by the ol
37. phone features offering and powerful voice processing power as possible The VIP 360PT can effortlessly deliver toll voice quality equivalent to the regular VoIP IP PBX connections utilizing cutting edge 802 1p QoS Quality of Service capabilities to encompass 802 1q VLAN tagging echo cancellation comfort noise generation CNG and voice compensation technology Meanwhile the dual Ethernet interfaces on the IP phone allow users to install in an existing network location without interfering with connections of desktop PC networks The VIP 360PT has streamlined wired IP telephone that provides additional features such as built in PPPoE DHCP clients password protected machine management call hold forwarding mute transfer waiting pickup caller ID speed dial 3 way conference last number redial incoming message indicator multiple call appearances and user intuitive web administration system Product Features e IEEE 802 3af Power over Ethernet e Full Featured enterprise SIP Desktop Phone e 802 1p QoS 802 1q VLAN e Full duplex speakerphone mic and speaker e Pixel based monochrome LCD with backlight e Efficient installation deployment of IP PBX solution Reversible base stand wall mount VoIP Features e SIP 2 0 RFC3261 compliant e Supports up to 3 service domains Interoperability with leading PLANET IP PBX platforms e Voice codec support G 711 A Law u Law G 723 1 G 729 A B G 722 G 726 e In band
38. r Cycle through the phone menu Adjusting Volume lower Checking Missed Call Checking IP info Checking Incoming call Checking line status Enter into the phone s menu Place the person on the other line on hold answering call waiting Press to mute sounds when at talk mode Transfer the person you are conversing to another line Release a call without off hook and quit LED inside if blinks remind user have new voicemail 2ABCabc E 7 A 7 e ypad OO OB a 4 n i JKL 5 Physical Interfaces Ethernet Cable Ethernet Cable headset Power on off WAN connection port POE Switch LAN connection port RJ 45 connector for Internet access connected directly to Switch Hub through straight CAT 5 cable 1 WAN The WAN interface also can be connected with 802 3af PoE switch or converter for power supply Chapter 2 System Setup and Basic Operating System Configurations for LCD WEB After Power on IP phone you should see some text on the LCD screen of IP phone now If not please redo step 5 to 6 until you can see some text on the LCD screen PLANET 13 40 45 2010 08 08 Sunday VOIP PHONE Network Setup Static To setup static IP address please follow instructions described in this chapter 1 Press button on IP Phone System Config Menu User Config Network 2 Press 4 key until Network is selected then press OK or Soft2 Enter key Menu System Con
39. replies SIP message with just one codec which phone supports Enable Disable the function when call is incoming phone replies SIP message with just one codec which phone supports Set to use automatically TCP protocol to guarantee usability of transport as message is above 1300 byte Support the special SIP server when phone receives the packets sent from server gt phone will use the source IP address not the address in via field Set to support GRUU Set to make quotation mark to display name as the phone sends out signal in order to be compatible with server Set to support GRUU IAX2 Config VOIP E sr 22 BS A ons arn TAK2 Server Add all Refresh Time Enable Register A O 1 BE IAX2 Config Field name explanation Register Status Shows if the phone has been registered the IAX2 server or not IAX2 Server Addr Input your IAX2 server address IAX2 Server Port Set your lAX2 server port the default is 4569 Account Name Input your IAX2 register account name Account Password Input your IAX2 register password Phone Number Input your assigned phone number usually it is same you re your IAX2 account name Local Port Set your local sport the default is 4569 Voice Mail Number Specify the voice mail s number Voice Mail Text Specify the voice mail s name Echo Test Number Set echo test number If IAX2 server supports echo test and echo test number is non numeric system could set an echo test number to replace the echo te
40. rk ID is C type Click the Add button if you want to add a new output rule Firewall Output Rule Table Index Deny Permit Protocol Src Addr Src Mask Des Addr DesMask Range Port 0 deny ICMP 192 168 1 14 255 255 255 0 192 168 1 118 255 255 255 0 morethan 1 Then enable out access and click the Apply button So when devices execute to ping 192 168 1 118 system will deny the request to send ICMP request to 192 168 1 118 for the out access rule But if devices ping other devices which network ID is 192 168 1 0 it will be normal Rule Delete Input Output Input v Index To Be Deleted Poo Delete Click the Delete button to delete the selected rule NAT Config NAT is abbreviated from Net Address Translation it s a protocol responsible for IP address translation In other word it is responsible for transforming IP and port of private network to public also is the IP address mapping which we usually say Legal IP address u0 T e SUBI NAT Equipment Inner network DMZ config In order to make some intranet equipments support better service for extranet and make internal network security more effectively these equipments open to extranet need be separated from the other equipments not open to extranet by the corresponding isolation method according to different demands We can provide the different security level protection in terms of the different resources by building a DMZ region which can p
41. rovide the network level protection for the equipments environment reduce the risk which is caused by providing service to distrust customer and is the best position to put public information The following chart describes the network access control of DMZ Inner Network area SECURITY Protocol Set IPSec ALG FTP ALG PPTP ALG APPLY NAT Table Inside TCP Port Outside TCP Port Inside UDP Port Outside UDP Port DMZ Table NAT Configuration Field name explanation IPSec ALG It is an encryption technology Select it to enable IPSec ALG the default is enable FTP ALG FTP is a service of connection layer which can transform intranet IP into extranet IP when intranet IP is sending out packet Select it to enable FTP ALG the default is enable PPTP ALG Select it enable PPTP ALG the default is enable Shows the NAT TCP mapping table Shows the NAT UDP mapping table MAT Table Option m 2122 O PS jo jeen Oop Transfer Type Select the NAT mapping protocol style TCP or UDP Inside IP Set the IP address of device which is connected to LAN interface to do NAT mapping Inside Port Set the LAN port of the NAT mapping Outside Port Set the WAN port of the NAT mapping Notice After finish setting click the Add button to add new mapping table click the Delete button to delete the selected mapping table DMZ Table 192 168 1 119 192 168 10 23 Shows the outside WAN port IP address and the inside LAN port IP address
42. rts with your set phone number will be sent via SIP2 line after the first several digits of your dialed phone number are deleted according to delete length Suffix optional Delete Length optional Phone Number Destination optional Port optional Alias optional Call Mode Suffix optional Delete Length optional Phone Number Destination optional Port optional Alias optional Call Mode Suffix optional Delete Length optional Destination optional rep 008610 SIP Y 3 This setting will realize speed dial function after you dialing the numeric key 2 the number after all will be sent out The phone will automatically send out alias number adding your dialed number if your dialed number starts with your set phone number You need set Phone Number Alias and Delete Length Phone number is XXXT and Alias is rep Xxx If your dialed phone number starts with your set phone number the first digits same as your set phone number will be replaced by the alias number specified and New phone number will be send out If your dialed phone number starts with your set phone number The phone will send out your dialed phone number adding suffix number When you dial 2 the SIP1 server will receive 33334444 When you dial 8309 the SIP 1 server will receive 07558309 When you dial 0106228 the SIP1 server will receive 0086106228 W
43. rvic unida 43 Digital Map Configuration ernernneennne nene nnnn anne nnne anne nnna naene 44 Phone BOOK Aaa a a t 46 FUNCION KEY A rae E ti 47 O iii 49 AUW ad OVISIO M tre ee a a ee ee Te re 49 Syslog CON so ii eel odo dia 0d 50 Config Send ni a ds 51 o A Ee eee ee ee 52 Js A A Oe ee RES Rar ee aia Vaade 54 JA E ooo 5 An 54 MIENTO ais alia a 54 Firewall A hse cece ad nas Sotto tad eee eae EME KE DME 99 NAT CONTO caca 57 VEN CONDRO conii a amaan aaa ki alas 60 PAD DEMO DCR HAAA e A CT PEO ER O t haa nae 63 7411910 RTO PECICA ON Soi 63 Chapter 1 Introduction Overview PLANET continues to bring innovation to the Voice over IP communications market with cutting edge products and Internet telephony manufacturing experience PLANET now introduces a new desktop PoE IP phone family the VIP 360PT The standard features of the VIP 360PT includes 3 line dual 10 100 switched Ethernet ports and integrated IEEE power over Ethernet 802 3af circuitry for offering a choice of powering and cabling options to help reduce cabling expenses and cord clutter To give most flexibility to users the VIP 360PT platform contains a graphic LCD with Back light 3 Line keys 6 memory key 3 soft buttons 9 fixed function keys and a navigation key The PLANET VIP 360PT desktop phone is engineered to make Easy to install communications cost effective to deploy self contained service integrated intelligent
44. s will be forwarded to the appoint phone directly The phone will Prompt the incoming while doing forward Appoint your forward phone number Select the special type of server which is encrypted or has some unique requirements or call flows Select DTMF sending mode there are three modes DTMF_RELAY DTMF_RFC2833 DTMF_SIP_INFO Different VoIP Service providers may provide different modes Select SIP protocol version to adapt for the SIP server which uses the same version as you select For example if the server is CISCO5300 you need to change to RFC2543 else phone may not cancel call normally System uses RFC3261 as default Transport Protocol RFC Privacy Edition Subscribe Expire Time Enable Conference number MWI Number Click to Talk Signal Encode RTP Encode Enable Session Timer Answer With Single Codec Answer With Single Codec Auto TCP Enable Strict Proxy Enable GRUU Enable Display name Quote Enable GRUU Set transport protocols TCP or UDP Set Anonymous call out safely Support RFC3323and RFC3325 Overtime of resending subscribe packet Suggest using the default config Set to use sever conference Input the number of the server s voice mail box Set click to Talk need practical software support Enable Disable Signal Encrypt Enable Disable RTP Encrypt Set Enable Disable Session Timer whether support RFC4028 It will refresh the SIP sessions Enable Disable the function when call is incoming phone
45. se the Voice VLAN ID as the tag 2 Startup VLAN if set Voice Data VLAN differentiated as tag differentiated and disables the DiffServ then system will not distinguish the voice and data all packets will use the Voice VLAN ID as the tag 3 Startup VLAN if set Voice Data VLAN differentiated as tag differentiated and enables the DiffServ then system will distinguish the voice and data and add the VLAN ID each other 4 Startup VLAN if set Voice Data VLAN differentiated as data untagged then the packet of the signal voice will use the Voice VLAN ID as the tag but the data packets will not take the VLAN tag 5 If Disable the VLAN regardless to set the Voice Data VLAN differentiated or not all packets will not take the VLAN tag If enable the DiffServ all packets will only take the DiffServ value 6 One must to notice enable the VLAN ID Check Enable that is default If enable it the phone will match the VLAN ID strictly When others VLAN ID not matches with us the packets will discard Contrarily the phone will accept the packets with the distinct VLAN ID 7 You must gain the IP with the Static mode when you set VLAN otherwise can t gain the IP in the VLAN and also can not dial with point to point Service Port You can set the port of telnet HTTP RTP by this page NETWORK KG MES SE serivce port eS EAA 0 Service Port 0 RTP Initial Port fi 000 RTP Port Quantity 200 SERVICE PORT Field name explanation HTTP Port set
46. ssumes no responsibility for any inaccuracies that may be contained in this User s Manual PLANET makes no commitment to update or keep current the information in this User s Manual and reserves the right to make improvements to this User s Manual and or to the products described in this User s Manual at any time without notice If you find information in this manual that is incorrect misleading or incomplete we would appreciate your comments and suggestions CE mark Warning The is a class B device In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Energy Saving Note of the Device This power required device does not support Stand by mode operation For energy saving please remove the DC plug or push the hardware Power Switch to OFF position to disconnect the device from the power circuit Without remove the DC plug or switch off the device the devices will still consuming power from the power circuit In the view of Saving the Energy and reduce the unnecessary power consuming it is strongly suggested to switch off or remove the DC plug for the device if this device is not intended to be active WEEE Warning To avoid the potential effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment end users of electrical and electronic equipment should understand the meaning
47. st text So user can dial the numeric number to test echo voice test This function is provided with server to make endpoint to test whether endpoint could talk through server normally Echo Test Text Specify echo test text s name Refresh Time Set expire time of IAX2 server register you can set it between 60 and 3600 seconds Enable Register Start to register the lAX2 server or not by selecting it or not Enable G 729 Enable or disable code G 729 by selecting it or not Stun Config In this web page you can config SIP STUN STUN By STUN server the phone in private network could know the type of NAT and the NAT mapping IP and port of SIP The phone might register itself to SIP server with global IP and port to realize the device both calling and being called in private network send request to Stun server from 5060 port apping sort 12345 AT stun server tell ant to receive data from 5050 aort Public Network Private Network VOIP SIP 1 STUN Field name explanation STUN NAT Transverse Shows STUN NAT Transverse estimation true means STUN can penetrate NAT while False means not STUN Server Addr Set your SIP STUN Server IP address STUN Server Port Set your SIP STUN Server Port STUN Effect Time Set STUN Effective Time If NAT server finds that a NAT mapping is idle after time out it will release the mapping and the system need send a STUN packet to keep the mapping effective and a
48. thrice back to main interface and at this time phone is trying to change to DHCP mode Press E until the phone shows DHCP If the screen shows the IP address and gateway which were set just now it shows that DHCP mode takes effect Network Mode DHCP IP 192 168 0 109 GW 192 168 0 1 Network set up from web 1 Use the web browser on your computer to connect to the IP address of IP Phone For example The IP Phone s default IP address is 192 168 0 1 please type http 192 168 0 1 in the browser s address bar A login window will appear please enter the username and password If you do not know the IP address you can look it up on the phone s display by pressing A button NOTE default username is admin and password is 123 A n a PLANETA T m 4 51 70 A gt XN 3 A f Networking Communication PA ogm lt After you configure the IP phone you need click save button in config under Maintenance in the left catalog to save your configuration Otherwise the phone will lose your modification after power off and on 2 After you have logged in you ll see the brief information of current network setting Please click Network link on the left PLANET BASIC NETWORK VOIP PHONE MAINTENANCE SECURITY BASIC status UN MIME Bes Connect Mode DHCP IP Address 192 168 1 36 MAC Address 00 30 4F 00 6e 20 DHCP Server OFF Phone Number ojejo 157 mwa 777 a
Download Pdf Manuals
Related Search