Home

TECHNICAL MANUAL ALPINE - the salomon technician programme

1. lt lt 528 ZZ lt osm LL SALOMON WARRANTY POLICY 3 SKI LENGTH 6 MAINTENANCE REPAIRS 8 RETAILS Technical 16 Mounting ens 17 Special cases in mounting amp adjusting 20 Adjusting 32 Final 36 RENTAL Mounting 39 WS DOC 42 FOOT ANATOMY AND 72 HELMET SALOMON WARRANTY POLICY Thank you for buying this SALOMON product They are built to last SALOMON distributes its products through its worldwide network of authorized SALOMON distributors and retailers and on the SALOMON Online Store at the URL www salomon com www salomonrunning com www salomonfreeski com SALOMON Online Store You will find herein below all SALOMON warranty policy details offered by SALOMON and the SALOMON authorized retailers WARRANTY DEFINITION THIS WARRANTY POLICY IS VALID AS OF NOVEMBER 1ST 2010 SALOMON provides this warranty to buyers who purchased the SALOMON product Product to SALOMON SALOMON Products are guaranteed against all manufacturing or ma
2. EDGE FINISHING For non equiped retailers they can do a classic tuning Lateral finish We recommend grinding the edges with a cup grinding disc see 7 Check the angle adjustment beforehand Lateral finishing with lubricated 220 belt or use the smallest grit possible Make sure the stones are well lubricated P ee um Make sure the edges are not burnt brown color au tM ML _ For a performance preparation polish the base edge with a polishing stone Check the tuning lengths Ret or whetstone to eliminate any file marks on the edges Remove burrs and polish edges with a lubricated Scotch Brite belt machine at a slow speed careful to lubricate sufficiently to avoid burning the base Carefully remove all burrs with a soft stone Quickly wipe the ski to avoid staining from the dried lubricant A well sharpened ski is always sharper underfoot than at the extremities of the ski Smooth the edges by hand with a soft stone or Scotch Brite Make sure all burrs are removed and smooth down again if necessary WAXING SCRAPING AND BRUSHING Tools Wax remover Wax applicator Brush with thermostat Plastic scraper It s best to use melted wax Clean the base thoroughly Make sure the iron is set at the appropriate temperature so that only the wax is melted Temperature 110 C
3. 5 C or 230 F 10 F Excess heat above 120 C or 248 F can be harmful to both wax and ski and can even cause permanent loss of glide qualities in the base Choose a wax according to the wax manufacturer s recommendations Melt the selected wax over the entire length of the base and let the wax cool to room temperature Remove the excess wax with a plastic scraper from tip to tail to leave only a very thin layer Remove wax from the base groove and ski edges as well P C lt gt is m Brush the base with a nylon brush or other type depending on the structure desired working from tip to tail Arotating brush removes the structure of the base for good glide Strap the skis together Position the straps at the base contact points Note The skis can be stored ready waxed unscraped for an extended period of time e g between ski seasons 10 HAND TUNING Tools Square 20 cm 8 inch file Whetstone Soft stone Scrapers Brushes Scotchbrite Sandpaper 220 320 grit Central holding vise Swix wax A true bar is the basic tool for checking and assessing Ski base flatness that the edge Is slightly recessed from the base the extent of base scratches and appropriate repair The edge angle checking tool is used to verify that the edge has an angle of 90 SKI CHECK UP Check the base and edges of your skis with a true bar
4. NOTE Salomon does not recommend the use of the custom fit machine or any other similar machine because it allows not an acceptable and effective Thermolight liner process CUSTOMFIT THERMOFORMING THERMOFORMABLE ZONES 1 Straight and anatomical tongue thermoformable internal side that provides precision and comfort An external side that is more rigid on the tibia and more supple in the flex area for excellent pressure distribution without hindering flex 2 Opened ankle area For ideal morphological adaptation regardless of the size and shape of the bones NON THERMOFORMABLE ZONES 3 Asymmetrical and rigid cuff Distributes pressure for instantaneous transmission of efforts 4 Watertight gusset 5 Specific cuts For women and men to avoid pressure points on the lower calf 6 More supple zones Allow for easy entry exit of the boot T Forefoot The space in front of the metatarsal is not thermoformable which allows the toes to move freely THERMOFORMING MACHINE Before using the machine for the first time return the guarrantee card to your Customer Service Representative Follow the instructions for the thermoforming machine closely and pay particular attention to the rules on safety To guarantee good thermoforming we have adapted a thermal sensor to our machines If something is abnormal during the heating process the machine will work alternately If this is the case contact the cust
5. 2 Toes 2 Heels mounted on a sliding part 2 Brakes Thin Plates m n Manni 1 Notice MOUNTING AND AJUSTING 1 Insert the Thin Plate in the seating ahead the plate fig 1 2 Place it correctly with a rotational motion fic 3 Identify the length of the boot 4 Identify the letter that corresponds your sole length If you are between two choose the higher one f 5 Screw the center mounting track to this letter 4Nm Torque fig 4 Mount the Toe piece as usual 6 From the rear slide the Heel piece on the interface using the manual lock to authorize the sliding fi T Mount the Brake following the usual procedure fig 8 Position your boot in the toe and slide the heel until it touches the boot fi 9 Step in the boot and check forward pressure fic The arrow on the housing must be within the scribed area Info The rear is an indication for quick adjustment of the second ski fi LIGHTRAK PLATE JL amp HL TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY MOUNTING AND AJUSTING 1 2 Open and set the blade in straight position and place it on the plate with a rotational motion fig 1 Identify the length of the boot sole 3 Mounting of the toe piece J L model Identify the letter that corresponds the sole length and screw the toe piece if you are between two letters choose the higher one HL model From the rear slide th
6. If repairs are necessary see instructions below SMOOTHING THE BASE AND EDGES Classic finish If damage is only minor use a file to tune otherwise the ski must be tuned on a machine Beveled Recessed finish the recommended bevel is between 1 and 1 5 EDGE SHARPENING Sharpen base edges Sharpen side edges On classic finish make sure the edges are at 90 On Beveled Recessed finish make sure that the beveled and recessed edge angle is between 1 and 1 5 Round off the tip and tail slightly Remove any burrs with soft stone or Scotchbrite POLISHING THE EDGES Polish the edges with a whetstone starting first on the base and then the sides DE TUNING THE EDGE ANGLE AT THE EXTREMITIES WAXING SCRAPING AND BRUSHING Follow the same instructions as in machine tuning Important After all finishing operations by hand or machine it is essential to remove any burrs from edges and to polish the edges to ensure good ski performance CLEANING THE SKIS Pressurized cleaners are prohibited as well as the following solvents Acetone 95 alcohol due to risk of damaging the cosmetics of the top surface of the ski MAINTENANCE SPECIFICS Tuning skis with prolink on automatically programmable machines and machines with a lead To be able to tune skis with the Y and V prolink we have developed a specific tuning kit in cooperation with the Wintersteiger company This new Prolink adapter
7. DESCRIPTION 1 Loop to tongue 2 Quicklace 3 Wide strap 4 SCS Salomon cushioning system 5 Walkable sole 6 PU lower shell and PP cuff 7 Micro alu overshaped buckles 8 Extra padded spoiler 9 My CF PRO liner with faux fur FEATURES ACCORDING TO DIFFERENT MODELS TECHNICAL DESCRIPTION GHOST 120 1 Loop to tongue 2 Quicklace 3 Energyzed strap 55 mm 4 Custom shell 5 Insole rubber grip 6 Absorbing footboard 7 PU lower shell 8 Double canting 9 Backbone 10 Micro alu overshape buckles 11 My Custom Fit Performance liner FEATURES ACCORDING TO DIFFERENT MODELS gt 6 5 69 FOCUS TO US ON YOUR TECHNICAL DESCRIPTION FOCUS 1 Oversize tool free catch 2 Articulated sensift for step in 3 2 buckle fastening 4 Auto Custom Shell technology 5 Rental plate for barcode 6 My AutoCustomShel liner Biovent FEATURES ACCORDING TO DIFFERENT MODELS PU materials to prevent scratches Aluminium buckles for lasting Liner mesh tested and chosen to ensure long lasting comfort Biovent less time needed to dry liner on the shelves Soles build to last and to avoid folding with textured effect Salomon patented AUTO CUSTOM SHELL TECHNOLOGY COMFORT SOLUTION TECHNOLOGY DIRECTLY DECLINED FROM OUR CUSTOM SHELL TECHNOLOGY AUTO CUSTOM SHELL 15 100 COMFORT ORIENTED PROVIDING COMFORT BENEFITS WIT
8. lengh 302 mm MAINTENANCE Proper maintenance of rental systems includes a complete inspection of the entire rental inventory prior to the ski season This should be followed by periodic in season inspections to help ensure that all components are functioning correctly gt Pre season 1 Visually inspect and clean all equipment in inventory 2 Test all bindings using selected reference boots and a mechanical testing device 3 Test a sampling of boots in inventory using selected reference bindings and a mechanical testing device In season 1 At specified intervals select samples from inventory to be tested 2 Inspect visually using the same procedures that apply to pre season End of season To prepare the rental equipment for summer storage lower all the binding release adjustments to the minimum Close the binding heel pieces Visually inspect clean repair and lubricate each rental system 1 To remove the heel slide the housing backward off the track 2 Clean the track with a damp rag or cloth Do not use solvents hot water or pressurized water to clean bindings Solvents may cause permanent damage to the plastic structure by dangerously modifying the products technical characteristics The markings can also be erased 3 Wipe any dirt from the underside of the heel housing and from the area under the open heel cup 4 Apply Salomon grease reference 000905 sparingly to the underside of the heel hous
9. INSULATION AND NUMBNESS Cold numb feet CRAMPS Muscle pain under the arch in the calf pressure points irritations SHIN BITE CAUSES Very narrow heel Achilles tendon axis very hollow Thin ankle Poor blood circulation caused by pressure on the blood vessels nerves Poor foothold distribution especially with children Pronounced arch high instep or flat foot Pronated foot Thick lower leg Lack of pressure distribution SOLUTIONS Solutions all products Stick a chevron above the calcaneus on the liner fig E Stick an L shaped piece of foam under each ankle bone for better grip Add a shim to the top of the liner forward position that pushes the foot backward in the boot and increases pressure on the heel Use a thicker insole Add a shim under the footboard Add heel lifts fig F Solutions all products Make sure the adjustments are not too tight gt Remove the insoles from the liners Add a small arch support and varus wedge or a shim on the inside of the heel under the footboard from the performance series Grind the footboard Solutions all products fig H Add or remove the arch support Add an insole or propose a custom insole Remove all shims under the footboard Modify the angle of the forward lean to distribute the skier s weight differently Grind the footboard Grinding the Custom Sole
10. If the sole at the contact points with the binding or AFD can be scratched with a finger nail the boot may be of inferiors quality and incompatible with the binding Boot sole condition If the boot sole is damaged worn or contaminated at contact points with the binding or AFD in a manner which can not be corrected the boot may be incompatible with the binding Brake compatibility with sole Rubber and or metal sole protectors If such materials contact the binding or AFD the boot may be incompatible with the binding f Mold flashings Flashing which can be seen or felt at contact points with the binding brake or AFD must be carefully removed 3 Remove from inventory all boots that have failed the visual check C Da PRESEASON BOOT SAMPLING Although sampling eliminates the need to test every boot before the season starts the sample chosen must be representative of the inventory 1 For boots that are new to inventory or have never been inspected take a single boot from each cell a cell is all boots of the same make model year and shell size 2 For used boots take a 5 but not less than 16 or more than 80 random sample of the entire inventory Make sure that there is at least one boot from each cell in the sample 44 PRESEASON BOOT INSPECTION The procedure that follows helps to assure both boot binding compatibility and boot interchange ability Note when using Chart A in the Boot
11. Inspection procedured that follow the Sole Length and Release Indicator Setting Columns should be ignored 1 Randomly select a pair of bindings that have passed the preseason inspection from each binding type adult junior child 2 Lubricate all boot binding contact points with a mild liquid detergent 3 Without regard to whether the boot is new or used sort the sample by sole type and length according to the 20 mm Sole Length Categories defined by binding adjustment chart 150 11088 4 In each Sole Length Category rank the boots by sole length and select the middle boot In each Sole Length Category fit the appropriate reference bindings to this typical boot and adjust the two bindings to release as close as practical to the Reference Torque in Chart A Use the Reference Torque corresponding to Skier Code L for the Adult binding J for the Junior binding and E for the Child binding Rinse the lubricant from one binding and mark it clean Mark the other lubricated Test each boot in the Sole Length Category with the clean Reference Binding and then the lubricated Reference Binding in both twist and forward lean only one direction in twist is required for the clean binding 8 Set aside any boots for which the lubricated Test Result is more than 2096 less than the clean Test Result in the same direction of release or the lubricated Test Result in any direction of release is outside of the Inspec
12. To increase the volume of the boot or to change the position of the foot Caution grind on the top surface only Grinding the base will affect the interface with the Chassis A depth gauge is marked front and back for even grinding Falcon fig Add a shin wedge on the cuff choose the mounting position according to the height of the skier 15 HELMET ADJUSTEMENT The helmet must be properly positioned on and adjusted to the user s head to ensure maximum comfort and protection A properly positioned helmet must not be too far forward or backwards on the user s head the chin strap must always be properly adjusted and in the closed position In case of children s helmets an adult should always check that the helmet is properly secured HEAD MEASURER gt Warning Salomon has developed a head measurer that will help you to better serve your customer by being able to recommend the helmet size that corresponds to the circumference of his her head This measurer can be used for all Salomon Alpine and In Line Skate helmets Please remember that the size given by the measurer centimeters should be used only as an indication to help you orient your customer toward the proper size The final selection of the appropriate size should be left to the customer Using the measurer should never replace trying on the helmet The helmet is a safety product it must be chosen in the size that is suita
13. as Type receive higher than average releasefetention settings This corresponds to decreased reieasability in a fall in order ta gain a decreased risk of inadvertent binding release This classification is not recom mended for skiers 47ib 2189 and under If from experience you have been dissatisfied with the release retention that result from your skier classification mention this to your binding technician RELEASE SETTING ADJUSTMENT Mandatory Release values Skier s parameters Skier s Skier s Skier Twist mass height code Mz N m Inspection parameters Examples for Initial indicator value These are only the starting point in the binding setting process and may need Forward lean My to be modified in order to achieve the correct measured release value Z presetting depending on boot sole length 331 to NOTE 1 For skiers of 13 kg and under no further correction is appropriate NOTE 2 For skiers of 17 kg and under skier type 1 is inappropriate a Lowermost tolerance limit b Uppermost tolerance limit ADJUSTMENT PROCEDURE The release setting adjustment is obtained by using the adjustment cap or adjustment screws The release setting is visible on the indicator Adjust the toe piece and heel piece to the same settings It is highly recommended to use a measuring device to check the release torque see ISO 11088 Release value selection and adjustment The release settings mus
14. available for rental equipment may be set up for fictitious skiers Only single skis not pairs are tested and testing at the toe is only required in one direction A count is maintained of test results which exceed allowable limits The magnitude and frequency of these deviations determines the frequency of future inspections Shops which fail an inspection must sample daily until the source of the problem is found and corrected Then as inspection results improve the frequency of sampling and inspection is relaxed INSPECTION PROCEDURES IMPORTANT TERMS CORRECTION FACTOR The value that must be added or subtracted from the initial visual indicator setting to bring the test result within the Inspection Tolerance or Inspection Range DIRECTIONS OF RELEASE Unless otherwise specified see Inseason Inspection the directions of release to be tested are forward lean and clockwise and counterclockwise in twist TEST DEVICE A device which meets ISO standard 11110 or ASTM standard F1061 and has been checked and maintained in the manner specified by the device manufacturer TEST RESULT OR RELEASE TORQUE The middle quantitative value of three tests made in the same direction Add other terms from ISO 13993 or ASTM F1064 that are not defined elsewhere in the tech manual PRESEASON TEST REFERENCE BOOT SELECTION The Reference Boot is a boot of a designated sole length which is otherwise typical of the boot in
15. binding can be readjusted These readjustments should allow you to obtain measured values as close as possible to the selected individual release torque within the 1596 range If the release is still outside the 30 readjustment range after having followed the procedures for malfunctions do not readjust the binding unless it is specifically authorized by the manufacturer chart 1 Three release Middle quantitative values value 60 50 50 50 dD 200100 60 Readjustment Tolerance range 65 Inspection Tolerance range 37 RETAIL BOOT BINDING COMPATIBILITY Clean vs lubricated test DIAGNOSIS Clean vs lubricated test 1 Determine the measured release value in the ski boot binding system without lubricant 2 Determine the measured release value in the ski boot binding system after lubricating all contact points between the boot and binding with a lubricant specified by the manufacturer If nothing particular is specified use soap and water Calculate the ratio between the two tests by dividing the result with the lubricant by the result without it 4 the quotient is above 1 2 or under 0 8 the system is considered to be incompatible If the boot test result is a satisfactory 3096 but the binding does not release within the readjustment tolerance range check the calibration of the adjustment machine Have another technician redo the test If the system still falls
16. can be mounted on the adjustable Wintersteiger bridge ref 2000 7217 0111 V01 and is available at Wintersteiger under the reference 7217 0111 V05 REPAIRING THE SURFACE OF THE SKI There are two methods for repairing the ski surface 1 One colored paste Araldite 2 Multi colored Araldite white coloring Materials needed Araldite 201 Araldite gun 50 ml Araldite coloring paste for smooth color DW 0131 White DW 0133 Red DW 0137 Black DW 0132 Yellow DW 0134 Green DW 0135 Blue White paste for undercoating for decoration DW 0131 White Felt pen to color the design type 3 points permanent Ref Pantone 87828 color number Accessories Cutter Adhesive tape Towel Sand paper Grain 600 Repair process 1 With a cutter outline the area to be repaired then cut the top surface photo 1 2 Result after cutting the top surface photo A2 3 With a cutter score area to repair fibers to improve bonding photos A3 4 To protect top surface put adhesive tape around the area to repair photo A4 5 Prepare Araldite resin with gun 6 Which type of repair to choose a One color surface repair b Multicolored surface repair 7 Add a small quantity of coloring paste to the Araldite resin Gently mix in order to avoid bubbles to obtain a homogeneous mixture Add a small quantity of coloring paste White DW 0131 to the Araldite resin
17. chuck touches the bushing of the jig When drilling the drill bit must be perpendicular to the surface of the ski The broken screw will come out inside the extractor bit Remove the screw using a pair of pliers Turn the ski over and tap lightly to remove all shavings Put a drop of glue into the hole Insert a plug from the kit using a hammer Insert binding screw and tighten using a hand driver Do not over tighten 12 When a hole simply needs to be widened to accept the plastic plugs use an 8 mm diameter bit Do not drill deeper than 10 mm gt onu Make sure you don t go beyond the plug once it is in place You can file it down to make it level with the surface MOBIL PLATE REPLACEMENT SCP Salomon Control Pedal All Salomon bindings have replaceable SCPs The specific SCP item numbers can be found in the Salomon Spare Parts catalog Replacement procedures for SCPs are follows On Toes tighten on Interfaces and Skis SMARTRAK GRIP GRIP PLUS SC ITF 78830101 for Z14 Z12 Ti 712 712 Ti SC 210 Ti AXE 210 Ti 210 Fis 20 Z10 Ti SC 710 710 Ti 710 SC 710 710 ITF 1 Dismount the Toe piece from the Ski or The Interface by completely loosening the mounting screws 2 Dismount manually the SCP on the Toe piece 3 Take the new SCP and mount it manually under the Toe piece 4 Tighten the Toe piece on the ski or the Interface 4Nm Torque On Toes SMARTRAK
18. defective heel track bent or broken base plate track or heel guide missing Delrin inserts in the heel guide jammed release adjustment unreadable indicators other visible wear T If it is obvious that the bindings release inadvertently unnecessarily at the request of the skier the dealer can At first increase the level in the forward fall that is on the heel piece Then only if the inadvertent releases persist increase the level in torsion that is on the toe piece Proceed very progressively in stages of half points 1 Visual inspection of system components 2 lest for elastic travel and return 3 Release value within specified range and boot binding compatibility The ski brake Check for improper installation broken entry pedals bent brakearms strength of ski brake brake must not compress totally when the ski is set on a flat surface other visible wear proper position of brakes They shouldn t touch the ski while they are functioning especially on fat skis The complete system Place the boot in the binding and check the accuracy of toe height adjustment if applicable toe cup width adjustment if applicable forward pressure adjustment release adjustment settings symmetrical mounting of bindings to ski center line 1 mm This should be in the same location on both skis If you discover a correctable problem repair the problem and
19. impact caused by sharp items due to torsion compression a fall an abnormal impact or other actions that cannot be under SALOMON s reasonable control The present warranty is not enforceable if 1 The Product is not returned in its original packaging if it has been modified or repaired by any person or entity other than SALOMON or an authorized SALOMON retailer 2 The Product has been repaired with unauthorized spare parts 3 The Product serial number has been removed deleted altered or made illegible Ill WARRANTY ENFORCEMENT In case of Defect SALOMON agrees to accept the claim replace or repair the Product at no charge for the end user and return it This shall be determined in the sole discretion of SALOMON or his authorized retailer unless this is impossible or disproportionate The remedy will be deemedto be disproportionate by SALOMON if it imposes costs on SALOMON which in comparison with the alternative remedy are unreasonable taking into account The value the goods would have if there were no Defect The significance of the Defect Whether the alternative remedy could be completed without significant inconvenience to the consumer SALOMON agrees that all repair or replacement of the Product will occur within a reasonable period and without any major inconvenience for the consumer taking account of the good s kind and its fitness for purpose The consumer is not entitled to have the
20. kit inscreases rear support with 3 height settings and forward lean by 2 Choose the desired height and attach using the screw provided in the pre drilled hole WATERPROOF GUSSET to guarantee a perfect waterproofness QUICKLACE KIT fig 2 1 Quicklace kit 2 Strap dismounting for replacement 3 Cover dismounting for replacement 4 Reassembing the new cover fuel racks 5 Backbone replacement 6 Reassembling the rear Perf hold WOMEN SPECIFICITIES PP Women cuff Women light back calf specific liner my Customfit Comfort liner QUEST MAX BC 120 For a better walk position place the upper buckle in the first position fig 3 66 PROCESS TO CHANGE FOLLOWING QUEST PIECES STRAP COVER BACK BONE 1 Dismount the rear Perf hold to access rivets 2 Drilling rivets with a 5 2 drill 3 Assembling new strap plate with inserts and screws M4 1 Drilling toe buckle teeth rivets with 5 2 drill 2 Drilling cover rivets with 5 2 drill 1 Drilling of the buckle teeth shell cover 5 4 to put the M4 insert 1 The insert must be flush with buckle teeth mounted on covert 67 Mounting kit 1 Remove the damaged axis by cutting off the reveting part 2 Place the 2 springs in their dwelling 3 Do not forget to put the steel Pin before screw and nut 4 Mounting of the new backbone F Steel Pin _ 68 Tk SUA n TECHNICAL
21. mm the axis between the talus astragalus and calcaneus becomes off centered which increases the surface area at the base of the foot Therefore to be accurate feet should be measured when the person is standing with his her weight distributed on both feet and knees slightly flexed 3 TYPES OF LEGS fig 3 Some people naturally have varus or valgus knees The boot cuff follows the profile of the leg Therefore the boot sole forms an angle with the ground the ski 1 not flat The ski boots can be adapted to the shape of the leg by canting the cuff The canting adjustment by canting the cuff allows the boot to follow the morphology of the leg to keep skis flat 72 A Normal knees B Varus knees C Valgus knees fig 4 A deeper analysis of the customer s feet is necessary to observe the possible deformations that can become problem areas Salomon has parts at your disposal that will help you to easily adapt the boots to these deformations High arches The skier needs an arch support that can relieve pressure on overloaded areas Arch supports can be attached to the footboards fig A Supinated or pronated feet This is the deviation of the foot s vertical axis towards the medial or lateral side which can lead to problems in the areas of the anklebones navicular bone or talus To adapt to this deviation of the foot it is possible to place wedges directly on the footboard
22. outside the range the binding should not be used Lubrification test qmm E gt lt uc LL SKIER INSTRUCTION AND WARNING 10 20 30 40 50 60 10 80 90 100 Torsion Nm In principle an adjustment report is established by the ski shop and delivered to the user 0 40 80 120 160 200 240 280 320 3 amp 0 400 It shall at least contain the following infor ation Forward flex Nm Clean test skier s parameters indicator value measured value of Mz and My or pass fail result of the system test The exact content of the report and its delivery conditions are defined by the national standard organizations 11088 Explanation of entry exit re entry The proper use of the system entry exit and re entry should be explained using the skier s own system as an example Receipt of in box instructions and warranty When a skier purchases a new binding it is required that s he also receive the instructional pamphlet included in each binding box 38 agy RENTAL MOUNTING The five steps to follow for mounting and adjusting rental bindings are the following 1 Preparation 2 Installation 3 Binding to boot adjustments 4 Release value adjustment 5 Rental visual and mechanical inspections PREPARATION It is important to maintain consistent procedures when mounting any Salomon binding Any boot used with a Sa
23. the 2 holes face the running base and screw 1 foil side fig D1 2 Set ut the tip protector on the lateral groove with a rubber hammer fig D2 3 Set up the tip protector on the central groove fig D3 4 Finish the mounting on the second lateral groove with a rubber hammer fig D4 13 4 REPAIRS REPLACING EDGES MATERIALS Standard Salomon edges for all skis ref 90190 REPAIR PROCESS 1 Verify that the ski can be repaired 2 Remove the binding and clean the ski 3 Check the length of the edge to be replaced fig 1 Cut out the base where the edge must be changed 10 mm beyond with the base patch die or cutter in this case make a reproducible cut out fig 2 4 Cut the 2 sides of edges between two wings with 45 angle as illustrated 5 Cut out the edge carefully with cutter or wood chisel then roughen the area with 80 grit Sandpaper fig 3 6 Cut the new edge trim it and remove the grease T Place the new edge and screw 2 wings near the tip Wedge in place in order to maintain a good profile and keep the edge horizontal fig 4 8 Apply epoxy to affected area and heat Slightly with heat gun concentrating on each wing 9 Put plastic over cut out area and insert piece of new base material 10 Cover the affected area with mold release paper and place ski in heat press fig 5 11 When the epoxy has cured remove
24. the liner and put them into the shell Take care to respect the right liner in right shell and vice versa liner aren t marked but differentiated only by the shape of the sole b Advice make one foot after the other preserve the liner not yet achieved in the Oven 5 Put the client taking good to push the client s heel all the way down to the liner to correctly set the heel to the bottom and thus do not create bends 6 Tighten the lacing system Quick Lace Close the shell starting with the forefoot buckle and making good attention to lock the backbone in the action possible 55 CUSTOMIZATION RECOMMANDATIONS FOR EXPERIENCED BOOTFITTERS You can use your regular heating tools though they would be less practical than the oven heating elements fig 1 gun fig 2 boiling water fig 3 Warning Kaprolene has been created to be deformed by the foot s natural pressure Be very careful if you need to use a pushing machine on the Kaprolene areas and NEVER push on the sides areas where Kaprolene meets the PU shell FAQ CUSTOM SHELL Can the shell change forms several times As many times as you want The wider the foot the more the shell will expand But it won t come back From what foot width will the Custom Shell be useful In size 26 from last 100 or 102 mm the customer Will feel a real difference The Custom Shell is also useful for thinner feet in order
25. 0422 52 91 JAPAN Tel 81 3 6831 2717 KAZAKHSTAN UZBEKISTAN Union Space Tel 998 71232 4440 KOREA Tel 822 518 0781 KYRGYZTAN Mountec Tel 996 772 545 610 LEBANON Sports Experts Tel 961 37 72 555 MACEDONIA Vrm Tel 38 975 217 720 MALAYSIA VGO Corporation Ltd Tel 65 6543 5828 MAURITIUS Emcar Tel 230 405 1000 MEXICO Tel 52 55 9177 9175 MONGOLIA Tel 976 1 3192 11 NEW ZEALAND Snoworld Sports Tel 64 3 366 11 22 NORWAY Tel 47 6755 1330 NEW CALEDONIA Ballande SAS Tel 687 28 78 39 Front cover Scott Markewitz Photos Fabrik d Images Studio Bergoend P 5 Deslandes J M Favre Scott Markewitz J L Michon C O Connel Pentaphoto Zoom SALOMON 2013 RCS Annecy 325 820 751 S A Conseil d Administration This document is not contractual SALOMON reserves the right to modify or discontinue any product Every product not available in all countries All rights reserved SalomonSports com PHILIPPINES Uniglobe Travelware Co Inc Tel 63 2303 1234 POLAND Tel 48 126 145 200 REUNION ISLAND Tel 336 92 64 62 ROMANIA Master Sport Tel 407 226 778 OO RUSSIA Tel 7 495 641 2646 SERBIA Beosport Tel 381 63 10 52 289 SINGAPORE VGO Corporation Ltd Tel 65 6543 5828 SLOVAKIA Tel 421 244 640 O11 SOUTH AFRICA Trail Terrain Tel 27 82 3313 005 SPAIN Tel 34 9326 25 100 SWEDEN Tel 46 33 23
26. 2 2 Normal foot 3 Supinated high arched foot 73 CAUSES Shell too narrow Prominent first metatarsal PROBLEMS FIRST METATARSAL PRESSURE medial side of the forefoot FIFTH METATARSAL PRESSURE lateral side of the forefoot Shell or liner too narrow Prominent fifth metatarsal ANKLEBONE PRESSURE Prominent medial Pain pressure behind one and lateral ankle or both ankle bones bones Heel shape HEEL PRESSURE Lack of room in the boot Prominent calcaneus exostosis SOLUTIONS Solutions all products Stick adhesive foam around the first metatarsal on the medial side of the liner fig A Stretch the shell locally with a heat gun and other tools designed for this purpose such as SIDAS except Symbio and Rear Entry X Wave Ellipse Performa Be careful not to overheat the Sensifit or instep gusset of the boot during the heating operation there is a risk of deforming it due to how thin this part is Solutions all products Remove the insole increases volume Stick adhesive foam around the painful area to dissipate the pressure fig B Stretch the shell locally using a heat gun and other tools designed for this purpose such as SIDAS except Symbio and Rear Entry X Wave Performa Be careful not to overheat the Sensifit or the instep gusset of the boot during the heating operation there is a risk of deforming it due to h
27. 3 700 SWITZERLAND Tel 41 41 784 26 26 TAIWAN Ting San lou Mountain Equipment Co Ltd Tel 886 229 516 693 TURKEY Cms Sport Tel 905 336 377 777 UAE IRAN Nik General Trading Tel 971 43 59 87 80 UKRAINIA Multi Sport Tel 380 979 719 968 USA Tel 1800 225 6850 USHUAIA Popper S A Tel 542 901 422 244 OTHER COUNTRIES Tel 33 450 65 41 41 S aLomonN
28. 48 230 lt gt 308 216 mm lt gt 304 mm 190 mm lt gt 246 mm Soles Lenght 39 RENTAL INSTALLATION For mounting Synchro Rental bindings follow the same procedure as for the retail bindings SYNCHRO CENTER CONTENTS OF THE BOX The heel mounted on a plate The toe mounted on a sliding plate The position indicator The premounted track assembly with yellow screw Adult skis Caution the toes mounted on the sliding plate are specific to RENTAL products Brake 1 Position the rental jig ref 001003 or 001040 for a fat ski rental on the ski 2 Then drill through the jig s proper bushings Follow the same procedure as for retail bindings drilling tapping glue 3 Mount the premounted track assembly orienting the sticker toward the back of the ski photo 1 4 Mount the heel aligning the holes and tighten the screws photo 2 5 Mount the brake according to the usual procedure 6 To Position the toe piece Place the toe mounted on the sliding plate in front of the track and slide it until it stops Depress the manual adjustment button located on the front of the toe and slide the toe all the way back Slide the indicator forward and clip it on the sliding plate photo 3 either manually or with a flat Salomon screwdriver ref 000902 T To adjust the toe Hold the toe and depress the manual toe adjustment button The toe is free to move p
29. ASURER FIT COMFORT COMFORT FEET ARE WARMER aai BECAUSE FEET ARE DRIER THE AT LEER HiT ez dn LILT Hw Le gt WOOL METAL INSULATED LINER 0 AL AHD TALE ED thermicfit i THE iin APs ee ONTHE WHO FOOT AND Teri TECHNICAL DESCRIPTION Three layer construction fig 1 A EXTERNAL LAYER FOR CONTACT WITH THE SHELL For pressure distribution and thermal insulation Polyethylene closed cell foam insulation warmth lightness better fit PVC Thermic Rental gt protection ruggedness durability Sensifit cuff construction for envelopment of the leg Supple exterior for contact with the shell and foot envelopment Anatomical tongue B MIDDLE LAYER For foot envelopment and power transmission Thermoformable PE CustomFit or self molding PU Autofit or pre formed PE Thermic Fit suppleness Transmission foam coming from the Neoprene family for quick reactions C INTERNAL LAYER FOR FOOT HOLD For warmth and comfort Polyurethane PU open cell foam envelopment breathability comfort High density CustomFit foam for superior envelopment The materials selected for this unique layering system were chosen to correspond to the demands of the different skier ability levels SALOMON OFFER DIFFERENT LINER MODELS My CustomFit 3D 3D construction vs traditional 2D pattern Pre shaped patented t
30. Any use with other ski boots could cause the ski binding boot system to be faulty and affect release characteristics which would increase the risk of serious injury while skiing Therefore skiers are warned not to use this product with any ski boots other than those meeting the Standards indicated above Skiers are advised to consult the dealer where this product was purchased or an equipment specialist at any SALOMON authorized ski dealer of this product for further information regarding which ski boots meet the standards listed above 3 Remove the plastic piece which holds the screw and remove the screw from the toe piece 26 27 2 Hiking aid can be set in 2 positions A High position p H Low position NOK gt 28 REPLACING SKI BRAKE CRAMPON BACKCOUNTRY Refer to the Salomon spare part catalogue to know which brake to use Use the crampon which is adapted to the ski waist width according to the different ski widths and binding models 1 Turn the screw A and remove forward the heel piece from the rear plate 105 mm got meat 1 Push backward the step in lift the binding and flip forward the hiking aid 3 Take the new ski brake A insert the two lugs and assemble the ski brake on the heel piece B 3 Before using crampons make sure that the hiking aid is in the low position NEVER USING CRAMPONS IN THE HIGH POSITION 4 From the f
31. EALER ONLY MOUNTING AND ADJUSTING EASYTRAK 17 L9 amp L 10 1 Insert the toe piece from the front and position on the track according to the boot sole length 2 Insert the heel piece from the back and position on the track according to the boot sole length eek e EASYTRAK C5 1 Insert the toe piece from the front and position on the track according to the boot sole length 2 Insert the heel piece from the back and position on the track according to the boot sole length 3 Step in the boot and check forward pressure RETAIL BACKCOUNTRY BINDING WTR TECHNOLOGY TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY D Wo COD WARNING MOUNTING amp ADJUSTING PROCEDURE THESE ALPINE BINDINGS ARE INTENDED TO BE USED ONLY WITH THE FOLLOWING SKI BOOTS 1 For mounting Backcountry bindings holes have to be drilled with the Alpine ski boots compliant with ISO 5355 standard Salomon mounting jig ref 32670501 to ensure a proper alignment of the AND binding Ski boots equipped with WTR technology 2 Mount the toe base plate and the step in by tightening the screws at 4 N m labelled kit of walking soles for touring skiing
32. H NO PROCESS LAST EVOLUTION FROM 104 TO 108 INSERT ARE DERIVATED FROM PU SAME DURABILITY ADJUSTMENTS AND PERSONALIZATION LOWER LEG ADJUSTMENT It is possible to change the lower leg adjustment according to the morphology of the skier s lower leg Adjusting the lower leg cable Place the lower leg cable in the desired setting of the buckle teeth on the medial side of the boot fig 1 Longer or shorter cables are available from the spare parts catalog to adapt to all shapes and sizes REPAIRS REPLACING THE LOWER LEG BUCKLE TOOTH INSERT 1 Remove the liner and open the cuff completely 2 Drill the rivet inside the shell 3 Remove the damaged buckle tooth insert and its rivet 4 Put a new buckle tooth insert in place and proceed as follows TECHNICAL DESCRIPTION SYMBIO 440 1 Rental thermic liner 2 Plastic buckles 3 Replaceable toe and heel pads 4 PU Shell and PP cuff 5 Bar code integrated to the liner FEATURES ACCORDING TO DIFFERENT MODELS gt Using a T nut 1 Place the threaded insert in the rivet hole on the inside of the boot 2 Put the buckle into place and install the screw tightly The prongs on the threaded insert should be completely imbedded into the cuff material 3 Loosen the screw 4 Put the washer into place This will prevent the tip of the screw from going too far 5 Tighten completely Using a Rivet Use a rivet on the outside and a washer
33. HOURS POWERLINE S1 24 HOURS POWERLINE S3 24 GT PRO 24 SPORT INTENSE BLACK ENDURO PURE WHITE ROCKER ROCKER CZAR SHOGUN LORD KNIGHT EL DICTATOR SENTINEL TWENTY TWELVE PRO PIPE SUSPECT THREAT GEISHA LADY GALAXY VAMP ORIGINS BAMBOO ORIGINS LAVA ORIGINS LIME ORIGINS LAGOON 4cm TOTAL This total centimetre length is a guide your preferred length will be the ski closest to the recommended total JUNIOR SKI LENGTH ACCORDING TO WEIGHT AND HEIGHT OF CHILDREN Child Height 8510 95 9510 105 105 to 115 125 to 135 135 to 145 145 to 155 155 to 165 165 to 175 cm Child Weight 1010 14 14to18kg 181022 22 to 26 26 30 301037 37to45kg 4510 55 5510 65 3 to 7 years old gt Approx 8 to 15 years old Age of the child gt _ Skiing Aptitude 70 80 FR Enduro 800 Jr XS 127236 Beginner oles ales FR Candy Jr XS 127244 Intermediate A FR Mini Kart XS 127228 E Enduro 800 Jr S 127234 Beginner E Candy Jr S 127242 Intermediate E Mini Kart S 127226 Beginner Intermediate Good E Enduro 800 Jr L 127230 Beginner E Candy Jr L 127238 Intermediate E Mini Kart L 127222 Good Beginner Intermediate Example for shogun jr A 6 year old child weighting 25 kg and measuring 120
34. However this wedge should only be used if the lateral articulation under the ankle bone is mobile fig B High instep You can grind the footboard Falcon and X Wave to increase the volume This sole is realized in grindable PU foam To increase the volume of the boot or to change the position of the foot Caution grind on the top surface only Grinding the base will effect the interface with the Chassis A depth gauge is marked front and back for even grinding fig C Low instep The height and inclination of the footboard can be modified by adding heel lifts fig D 5 RECOMMENDATIONS The modifications that can be made on the Salomon boots should be considered as the final touch of personalization Before undertaking this type of operation it is important to observe certain basic rules Always proceed step by step starting with temporary measures before going on to permanent changes If you decide to proceed with the permanent modifications as a last resort they are entirely your responsibility They require the proper tools and should be undertaken only for big problems and by experienced specialists For example Stretching the shell Grinding the liner not recommended for manufactured liners Grinding the shell Important Boots whose lower shell material is not made of Polyurethane PU should not be heated risk of damaging the material 1 1 Pronated flat foot
35. NING Salomon developed a foot measurer that will help you provide better customer service by being able to recommend the size that corresponds to the dimensions length and width of the skier s feet However using the measurer can never replace trying on a boot The volume fit can be measured in two dimensions The morphology of the foot and physical sensitivity of each individual according to his her sports activities and level comfort performance ratio are also determining factors in the choice of size The Salomon measurer can be used for all Salomon footwear products Alpine X C Hiking In line skates Snowboard and takes into account the two fundamental dimensions of both feet The length main measurement it can be read directly on 5 international size scales US men s US women s UK EUR Mondopoint The width in direct correlation with the length measured The width measurement is particularly useful to refine the measurement in Mondopoint because it orients the customer towards the 0 sizes narrow feet or 5 sizes wide feet PROCEDURE 1 Have your customer take off his her shoes and make sure that he she is wearing appropriate ski socks size and thickness 2 With your customer standing up legs parallel and knees slightly bent make sure his her heels and medial side of both feet are touching the sides of the measurer 3 Slowly move the length guide A until it touches the tip of one foot IMPO
36. NSPECTION 1 Take a random sample of the rental inventory as determined by Chart B Take half the sample from inventory as it is either rented or returned and the remainder from inventory available for rental 2 Wipe the boot clean and cycle the boot binding systems at least once in each direction 3 Test sample units in Twist one direction only and Forward Lean 4 Compare the Test Results with the Inspection Range for the appropriate Skier Code The program uses random samples of rental inventory taken at routine intervals Any sampling program that gives every unit of 5 f the results are within the Inspection Range the unit passes 6 If the results are outside Inspection Range but within the In Use Range count the unit as a Class Deviation T If the results are outside the In Use Range count the unit as a Class Deviation 8 Check elastic travel and visually inspect the ski brake function interface areas between boot and binding including AFD lug height adjustment if appropriate and forward pressure Count any deficiencies as Class Deviations inventory the same chance as every other of being picked is valid 9 If more than the maximum number of Class Deviations given in Chart B are found in the sample or a single Class Deviation is detected the sample fails and daily sampling must be conducted until the problem which led to the failed sample is found and corrected For Troubleshooti
37. PROLINK CONTROL RESPONSE 78829401 for SMARTRAK PROLINK 914 78829501 for SMARTRAK PROLINK amp SMARTRAK CONTROL 714 212 710 711 78829601 for SMARTRAK PROLINK amp SMARTRAK CONTROL 712 Ti 710 Ti 710 Ti 1 Put the Toe Piece out the Interface 2 Dismount the Toe piece from the Set by completely loosening the mounting screws 3 Dismount manually the SCP Stirrup on the Toe piece 4 Take the new Set SCP Stirrup and mount it manually under the Toe piece 5 Tighten the Toe piece on the Stirrup 4Nm Torque 6 Remount the Toe piece on the Interface JUNIOR 5 amp 5 AND L 7 8 9 10 anti friction plate replacement 1 Insert a screwdriver width 6 8 mm at the front of the plate fig 1 2 Move over the screwdriver to eject the plate fig 2 3 Place the new plate and hand clip it fig 3 amp 4 Caution for models with elastic pedal range 08 check the presence of the elastic block under the pedal fig 5 46 THERE ARE DIFFERENT STANDARDS ISO 5355 AND TOURING 9523 BOOT STANDARD The Alpine boot soles are standardized and bindings are designed accordingly The standard norm concerns not only the shape and dimensions as illustrated but also the friction coefficient of the area of the sole which is in contact with the anti friction plate on the binding In practical terms The boot manufacturers who display one of the following markings DIN ISO ON
38. RAL ANGLE POSITION OF THE BODY X3RCCS TI I2 5 MAX SERIES 12 13 lt 3 FORWARD LEAN uu eXBRCCSTINZ 155 1 SERIES 12 13 13 5 LANGE R5 130 2 5 ii bod gt 4 5mm BETTER MORE ROOM HEEL HOLD IN THE TOF BOX 64 EASY TO REMOVE amp CHANGE 4 SCREWS 4 SCREWS 4 SCREWS DIN SOLES WALK SOLES WALK SOLES ALPINE NORM WTR amp TOURING NORMS WALKING SOLE PADS These walking sole pads are intended to be used only with the following bindings Touring bindings compliant with ISO 13992 standard WIR technology labeled alpine bindings compliant with ISO 9462 standard Any use with other bindings could cause the ski binding boot system to be faulty which would increase the risk of serious injury while skiing These walking soles are removable and should be replaced if excessively worn and or damaged Salomon guarantees the soles for their disassembling and reassembling WALK SOLES WITH LOW TECH INSERTS up to a maximum of 5 times subject to strict compliance with the following instructions Use only a manual screw driver Unscrew the 7 screws and remove them from the sole Remove the rear and front sole Push them forward towards the front of the shell and rescrew until you feel an increased resistance in the torque to reach a torque value about 1 5Nm Q 65 REAR SPOILER fig 1 The rear spoiler from the performance
39. RTANT When you are moving the black transversal length guide make sure you don t put any pressure on the toes when measuring the foot All you need to do is to barely touch the end of the longest toe Too much pressure on the toes could lead to errors in reading by a few millimeters 4 Read the size written vertically where the red line is in the window B For Mondopoint you have to take the width into account in the following manner if the length of the foot measured is situated in this zone this means the foot measures between 260 mm and 269 mm Then to choose between 26 0 and 26 5 you must look at the width scale C in this case make it correspond to the maximum foot width with size 26 A foot that measures 261 mm would fit in size 26 5 wide foot whereas a foot that measures 268 mm can fit in size 26 0 narrow foot D NOTE The increases in Mondopoint sizes represented by two triangles in a rectangle is made to remind you that the boot sole lengths change at the whole sizes not the half sizes Remember that the size indicated on the measurer should be used to help the dealer orient the customer towards the proper size The final choice as to the appropriate size should be left to the customer depending on whether he she prefers a snug fit or not In principle a technical skier who appreciates a snug fit will choose the size indicated on the measurer while a recreational skier will prefer a roomier fit and wi
40. THERS SKIERS TYPE Type I skiers Skiers looking for a lower release setting than type 1 Recommended for beginners over 25 years old Type III skiers Very strong skiers on challenging terrain Skiers looking for a higher release setting than type 3 skiers Skier type does not have the same meaning as skier ability For instance an advanced skier who skis all terrain but is not particularly aggressive may be able to use Type 2 settings ADJUSTMENT PROCEDURE 1 Find the skier s code in chart 1 Locate the skier s weight in the first column and the skier s height in the second column If the skier s weight and height are not on the same row select the skier s code on the highest row 2 This skier code is appropriate for Type 1 skiers For Type I skiers move up one row For Type II skiers move down one row towards the bottom of the chart For Type III skiers move down two rows on the chart For Type III skiers move down three rows on the chart 35 RETAIL 3 For skiers who are 50 years or older or un der 10 years move up one row on the chart For skiers weight 13 Kg and under no further correction is appropriated For skiers weight 17 Kg and under type 1 skier is inappropriated 4 After having determined the skier code locate the column in chart 2 that represents the skier s boot sole length in mm 5 The box at the intersection of the skier s boot
41. UNI guarantee that they use standard norms In the absence of any of these check first with the boot manufacturer BOOT SOLE LENGTHS X Lab Alpine norm ISO 5355 7 18 15 16 20 21 X Pro X Pro Women Mission Divine Quest Max Quest Max BC Quest Quest Women Quest Access Quest Access Women Ghost Max SPK X Max LC Quest Access T X3 60 T 240 240 247 257 T3 Team T2 Team 240 240 247 259 Ti 208 208 223 223 Focus Focus Women Symbio These boots are designed for use with a pair of classic skis with alpine bindings and not with a monoski snowboard or skiboard Touring norm 150 9523 These boots are designed for use with a pair of touring bindings and not with alpine bindings monoski snowboard or skiboard It is the skier s own responsibility if s he chooses to take the additional risks When a pair of used boots is brought in make sure that any worn parts are still within the norm Your ski boots must be assembled adjusted and checked by an approved Salomon technician 22 5 23 5 LAST RECAP PER CONCEPT MODELS LAST95 mm LAST98 mm LAST 100 mm LAST102 mm LAST 104 mm LAST 106 mm LAST 108 mm X Max X Max Women X Pro X Pro Women 48 ww X 22 23 24 25 24 5 25 5 29 5 IN 29 30 31 32 33 30 5 31 5 32 5 33 5 337 357357 MEASURER THE SALOMON MEASURER WAR
42. White paste is used as a primer in order to have the desired colors afterwards Gently mix in order to avoid bubbles to obtain a homogeneous mixture photo A5 8 Apply thicker than top surface of the ski in the areas to be filled Wait a few moments to eliminate bubbles if necessary photo A6 9 Put adhesive tape on the area to avoid running Let it dry for 12 hours photo 10 12 hours of drying remove the adhesive tape from the mixture Do not remove the adhesive tape around the area which protects the top surface from scratches Use the flat side of a cutter to scrape off the excess mixture photo A8 Smooth it down with 600 grain sand paper Remove the adhesive tape photo A9 12 Finish sanding gently in order to obtain a smooth surface Be careful of the ski s decor cosmetics MAINTENANCE REPAIRS HOW TO CREATE A DECORATION 13 For the coloring stage do not try creating tone on tone to create the exact color of the ski Trying to reproduce a motif of the ski design already present elsewhere is better and easier The final layer of Araldite tends to lighten colors photo 10 14 Use the Araldite gun for a varnish finish which will protect the ski surface from cuts from the edges A small quantity of Araldite is sufficient 15 Apply a fine layer of Araldite with a cutter to avoid excessive thickness photo A11 m EUM A 16 Us
43. ation of tightness in the shell 2 Define possible painful areas painful pressure points 3 Determine amp protect those areas with cut foam pads not included to the contact of the foot not the sock Although be careful to not take off amp remove the pads when step in to the socks 4 Put the Thermolight liner without insoles 10 minutes in the custom shell oven at 100 max preferably already heated 5 At the end of 10 minutes add insoles original custom or orthopedic in the liner and put them into the shell Take care to respect the right liner in right shell and vice versa the liners aren t marked but differentiated only by the shape of the sole Advice make one foot after the other pre serve the liner not yet achieved in the oven 6 Put on the client taking good care to push the client s heel all the way down to the liner to correctly set the heel to the bottom and thus do not create bends T Tighten the lacing system quick lace 8 Close the shell starting with the forefoot buckle and making good attention to lock the backbone in the action position 9 Provide a clamping adapted according to the morphology of the worked foot Strong 2 3 and 4 teeth for a wide foot Low tooth 1 2 amp 3 for a thiner foot Repeat the same operation for the 2nd liner 10 Cool down 15 minutes at room temperature and in a natural standing position without exaggerating the bending on the front
44. ble to its user and be properly positioned on his her head the chin strap adjusted in the closed position to ensure optimum protection comfort and hold Recommendations for use e Loosen the roller A to be able to place the measurer easily on the head e Position the measurer on the head according to fig n 1 touching the brow B and the occipital bone C Important Make sure the headband D does not compress the ears which would affect the measurement e Hold the measurer in this position and turn the roller A rotate it clockwise e Turn the roller until it disengages fig 2 e Carefully remove the measurer from the head pulling the rear upward while maintaining pressure on the nose fig 3 e Read the measurement on the graduated scale E in the window fig 4 e Choose the helmet according to the size given by the measurer e Try the helmet on Switch sizes if there is a problem with the fit Salomon has provided for stickers that can be put on the head measurer for a better understanding of how to use the roller Maintenance recommendations To clean the measurer you can use a cloth with soap and water It is prohibited to use chemical products hot water or pressurized water gasoline alcohol detergents solvents or aerosols that could permanently damage the plastic materials and erase the markings gt Warning Salomon does not cover any damage to the head measurer that is a result of transporta
45. cm with intermediate skiing abilities must choose a 110 cm ski with a T5 binding If weight is over 65 kg 142 Ibs SALOMON strongly recommend to use an ADULT ski RECOMMENDATIONS OF USE OF THE SKIS ACCORDING TO THE MASS OF THE SKIER To guarantee the sufficient parameters of safety i e the resistance of the screws to wrench skiers must use skis according to groups 1 to 4 below corresponding with their weight EN NN NE gt 650 lt 65 kg 2450 1 2 3 4 25 kg extract from NF ISO 8364 june 2007 MAINTENANCE REPAIRS SKI MAINTENANCE Good ski maintenance is just as important for the recreational skier as for the racer A fine tuned ski lasts longer A well prepared ski turns better grips the snow better and glides better on all types of snow The ski tune up involves three steps 1 Daily check up at the end of everyday of skiing 2 Machine tuning for quick work 3 Complete hand tuning for skier s specific needs CHECK UP Visually check to see if any rust has developed on the edges Remove any traces with fine 220 230 grit sandpaper f necessary sharpen and polish edges using sandpaper wrapped around a file Clean the base and wax with Swix wax MACHINE TUNING Visually check to determine what needs to be tuned Remove major deep scratches on edges with whetstone Remove any traces of wax or grease FILL IN ANY HOLES IN THE BASE Depending on the condition
46. contract rescinded if the Defect is minor For all warranty claims please produce the Product and the proof of purchase to the nearest authorized SALOMON retailer or in case you purchased the Product on SALOMON Online Store please contact Customer Service at 0800 90 44 03 For all warranty claims please report to the FAQ RETURN POLICY available on www salomon com Add to that number any additional length from the boxes below according to you r ability aggressiveness the snow conditions you ski most of the time and the kind of skis you want to choose nen ___ oe won we o gt Corresponding SKI LENGTH cm 140 145 150 155 160 165 170 1 BEGINNER 2 INTERMEDIATE 3 ADVANCED 4 EXPERT 5 SPECIALIST You are skiing Able to ski Able to ski Able to ski Able to ski on all the first week most runs all runs on all runs runs in changing Rental skis in good conditions in good conditions in any conditions conditions 10 cm 5 5 10 Discover first Prefer moderate Prefer a variety Prefer Prefer highest ski sensations speeds of speeds high speeds speeds TERRAIN Most of the time on groomed piste or on hard snow conditions Most of the time off piste or on soft snow conditions 60 gt 60 5 TARGET KIND OF SKI 3V POWERLINE 2V RACE POWERLINE 24 HOURS MUSTANG X KART 24 DAYTONA 24 HOURS POWERLINE LM 24 HOURS POWERLINE 5 24
47. dability and travel d Screw tightness e other product specific inspections if required 3 Fit each binding to the Reference Boot and adjust the release indicators to the value in Chart A 4 Check that the heel track and toe track code if any agree with the sole length code if any of the Reference Boot 5 With the Reference Boot in the binding verify elastic travel of the toe piece by striking the boot toe with a mallet or dead hammer and checking that the toe piece returns the boot quickly and completely to center 6 Verify elastic travel of the heel piece by lifting the boot while depressing the heel Release Reference Reference Forward Forward indicator setting E Children 258 2 0 20 J Junior 306 4 3 43 L Adult 327 5 8 58 torque inspection inspection in use in use forward range range Nm Nm Nm T5 Wes 64 87 14 27 52 102 165 37 50 141194 31 58 120 229 229 50 67 194 271 43 78 165 320 piece cocking lever and checking that the heel piece returns the boot quickly and completely to the latched position other product specific procedures if required T Manually release the binding 3 times in each direction 8 Lubricate all boot binding interfaces with a mild liquid detergent and water solution 9 With the Ski Binding Test Device determine the Release Torque for each direction of release forward lean and both directions in twist 10 Record PASS in the binding s main
48. ding Quest Max Quest Quest Access Ghost Max Warning cantable alpine pads are not com pliant to 150 5355 and must be grinding before using to reach the norm Grinding should be done as well on top and on at the bottom of the alpine pad with the same angle in order to guarantee surfaces parallelism fig 3 TO OND 3 MAM 2 MM Grinding on top and bottom surface should not go over the reference line marked on can a 3 ss 1 j 2 a ud cc a a T 1 Ti T 4 z m gt TO GRIND T aay gt gt GRIM b j io p 5 4 ht 5 f b Fi t j Rum EL __ 1 4 p table alpine pads which allow an angle from MAX 2 MM 0 to 1 5 fig 4 TO GRIND 60 ADJUSTMENTS AND PERSONALIZATION MICRO ADJUSTABLE BUCKLE fig 1 Fine tune the buckle closure by turning the part that grips the buckle teeth REMOVABLE REAR SPOILER You remove it by clipping A TOOL FREE CATCHES ADJUSTMENT fig 2 Upper catches are also adjustable with or without tools to adapt the volume of the upper cuff to your calves To move upper catches a turn them 90 move them laterally 15mm then place them back to their horizontal position To move lower catches b loosen the screw with a 3mm Allen wrench position the catches in the de
49. e 5 Double dismantable canting 6 Ride amp Hike body postioning T Magnesium backbone 8 My CustomFit Pro liner FEATURES ACCORDING TO DIFFERENT MODELS ADJUSTMENTS AND PERSONALIZATION WOOL METAL LINER The Wool metal insulation is a mix of wool and metallic polyester layer to keep your feet warmth wool on toe inside insulation between foot and shell RIDE AND HIKE TECHNOLOGY new body positioning Forward lean better balance Cuff opening wide cuff opening on the back when walking natural leg position TECHNICAL DESCRIPTION 1 35 mm strap 2 Removable pads 3 Single canting 4 backbone 5 Micro alu buckle ratchet 6 Wool metal My Custom Fit sport liner FEATURES ACCORDING TO DIFFERENT MODELS ADJUSTMENTS AND PERSONALIZATION RATCHET BUCKLE Micrometric adjustment wider range of adjustment 45 mm compared to classic alu Maximum conveniency for adjustment Easy to pump to close the cuff 63 BOOT CONCEPTS A UNIQUE amp PATENTED RIDE amp HIKE TECHNOLOGY ALPINE BACK SUPPORT MANAGEMENT ALPINE FORWARD FLEX MANAGEMENT INNER SHELL V CUT OUT THE MAX SERIES FOOT POSITIONING RAMP ANGLE amp LATERAL POSITION FOOT POSITIONING FORWARD LEAN SKIS ARE GETTING MORE BETTER HEEL HOLD FOR PRECISION amp MORE FAT AND MORE ROOM IN THE TOE BOX ROCKER IS EVERYWHERE FOR BETTER FEELING EVEN ON CARVE SKIS gt NEED STRAIGHTER LATE
50. e Salomon mounting jig ref 11847301 to ensure a proper alignment of the binding Sole Monting lengts oh Heel rail inmm Mounting of toe rail 265 am 275 n 285 S 295 5 305 315 325 335 345 355 360 MOUNTING PROCEDURE 1 Mount the base plate toe by tightening the screws at min 4 Nm 2 Mount the heel base plate by tightening the screws at min 4 Nm and mount the brake by tightening the screws in the middle at min 4 Nm 3 Push the VAR lever over to the right and Slide the toe piece from the middle towards the tip of the ski 4 Move the toe piece to the number corresponding to the boot sole length you would like to mount the binding for 5 Slide the heelpiece from the tail forward 6 Match up the steel band with the boot sole length you would like to mount the binding for T lake the AFD pedal and place it in the middle and fix it with screw at max 4 Nm 8 Put the boot into the binding and check the forward pressure The screw head needs to be aligned with the housing Toe PIECE POSITION on the toe rail Position 7 Position Position 7 Position 6 Position 5 Position 5 Position 4 Position 3 Position 3 Position 2 Position 2 j w a Ar 2 Check the boot sole length you would like to mount the binding for and drill the S M holes which are marked on the jig following
51. e pivot on XMAX 130 is screwed and could be disassembly in order to take out the cuff from the shell for bootfiting specific key is provided with the boot for this operation For reassembly the oversize pivot should be tight at 5 5 Nm torque value CANTING Canting could be adjusted by following operations by an approved Salomon technician Internal boot sole grinding fig 5 Chassis grinding which should be conform to the ISO 5355 after the operation Chassis grinding on XMax 130 model 4mm canting lifters kit available for XMax 120 and 100 models This kit allows an adjustment of 0 7 in function of the lifter side mounting fig 6 Maximum screwing value 0 8Nm Maximum assembly disassembly 5 times Lifter with 0 79 LIFTERS ON XMAX 120 AND 100 4mm lifters are removable and should be replaced if excessively worn and or damaged Salomon guarantees the lifters for their disassembling and reassembling up to a maximum of 5 times subject to strict compliance with the following instructions Use only a manual screw driver Unscrew the 12 screws and remove them from the lifter Remove the rear and front sole Push them forward towards the front of the shell and rescrew until you feel an increased resistance in the torque to reach a torque value about 0 8Nm maximum as mentioned on the lifters fig 7 BACK BONE Increases the junction between cuff amp shell for flex managem
52. e toe piece on the interface until it corresponds with or is just above the sole length push the bolt until the clic to lock on the toe piece fig 2 Note to move the toe insert a screwdriver and with a rotational motion lock off the bolt fig 3 4 Mounting of the heel piece model From the rear slide the heel piece on the interface using the manual lock to authorize the gliding fig Mount the brake following the usual procedure fig 5 Position the boot in the toe and slide the heel until it touches the boot Step in the boot and check forward pressure the arrow on the lock must be within the scribed area fig 6 Note the rear N on the blade is an indication for a quick adjustment of the second ski H L model From the rear slide the heel piece on the interface using the manual lock to authorize the gliding fig 4 Mount the brake following the usual procedure fig 5 Slide the heel piece until it corresponds with or it just above the sole length Step in the boot and check forward pressure the arrow on the lock must be within the scribed area fig 6 22 12 amp X 16 TO BE MOUNTED SALOMON AUTHORIZED DEALER ONLY DRILLING SKIS 1 For mounting the X 12 amp X 16 bindings on skis holes have to be drilled with th
53. echnology Thermoformable inserts around ankle amp heel Solve instant pressure points around ankle amp heel Offers unmatched foothold My CustomFit World Cup Best performance Extra low volume Compact Race liner 3 layers Specific World Cup tongue allowing shock absorbing My CustomFit Race Best performance Low volume Compact Race liner 3 layers Rigid sole My CustomFit Pro Maximum customization with 3 layers of thermoformable foam on the ankle heel meta tongue sole for perfect comfort and transmission My CustomFit Performance Better comfort on the heel metas amp sole without altering performance Two layers liner thermoformable foam 8096 on all sensitive areas heel metas sole My CustomFit Sport Better customization of the tibia and ankles One layer liner thermoformable foam 7096 on original areas My CustomFit Comfort Better tibial customization One layer liner thermoformable foam 6096 on basic area tongue ThermicFit Comfort and warmth Pre formed zones protect the tibia and the forefoot pleasure to slip into due to its construction and materials Xfit Active A comfortable single layer constructed thermo moldable liner with customizable tongue area for shin comfort and a wide ankle area positioned at the back of the leg for heel lock XFit Advanced A comfortable single layer constructed thermo moldable liner with customizable tongue area for s
54. ed release value should be considered to be the middle quantitative value of three measured releases If the first two measured values are the same there is no need to take a third measurement See examples of middle quantitative values Chart 1 The toe passes this inspection if the middle quantitative values in both directions fall within the Inspection range See sample System inspection ranges Chart 2 Symmetry test note You should be aware of the possibility of an asymmetric release If your tested values for clockwise and counter clockwise release appear to be at opposite extremes of the inspection range you may have an installation error or incompatible boot Troubleshoot the system and re test after the problem has been corrected gt Test the heel First exercise the heel by releasing it once Using a test device measure and record the heel release value The middle quantitative value of three heel releases should fall within the 15 inspection range Release value verification failure When the technician is satisfied that all required procedures have been completed according to Salomon s recommendations in this manual he or she must sign the Workshop Form The signing technician must currently be certified by Salomon Note During manufacturing Salomon precision tests every binding up to 5 times to assure that it functions properly and is calibrated correctly It is e
55. eezing Skis Widths Adult Line Senior 001156 56 mm lt gt 99 mm 001040 001157 80 mm lt gt 123 mm 78406101 Junior Rental Line Senior and Junior 56 mm lt gt 99 mm 001003 80 mm lt gt 123 mm X RACE JR ROCKER JR SUSPECT JR Q MAX JR Q LUX JR ski G3 G4 ski G1 62 3 6 mm 4 mm No No glue 3 Nm For these skis use a hand screwdriver only to tighten the screws on the bindings Application Senior Lenght drilling 9 5 mm STH 16 14 12 Driver STH 12 Z14 12 11 10 L10 9 Junior Lenght drilling 8 mm L7 Junior 56 mm lt gt 99 mm Lenght drilling 8 mm T5 C5 Synchro Center Adult Synchro Rental Adult Lenght drilling 9 5 mm 2 12 10 SC L 9 10 SC amp SR L7 SC Lenght drilling 8 mm L 7 SR Synchro Center Junior Synchro Rental Junior Lenght drilling 8 mm T5SC T5SR C5SR Senior 78840301 SMARTRAK 70 lt gt 116 mm Lenght drilling 9 5 mm 24729001 Junior 56 mm lt gt 99 mm ome TZ 5 Juniortrak 11847301 X bindings Senior Lenght drilling 9 5 mm lt gt X 20 18 16 12 Easytrak 70 gt 116 mm Senior Lenght drilling 9 5 mm Backcountry 56 gt 143 mm Senior Lenght drilling 9 5 mm 56 gt 143 mm Senior Lenght drilling 9 5 mm Incorrect NE d positioning A positioning RETAIL DRILLING 1 Follow the recommendations of the ski manu facturer for drilling and ta
56. efiting from specific Fit foams disposed on the anatomical areas to increase head comfort Custom Air System fig 2 Adjustable Air system for a perfect fit THERMO CONTROL SYSTEM ACTIVE VENTILATION ALL THE BEST TEMPERATURE REGULATION ALLOWS YOU TO MODIFY THE AMOUNT TECHNOLOGIES AVAILABLE ON THE MARKET OF AIRFLOW AND HEAT EXHAUST OSFA fig 3 With this adjustment system the helmet is covering several sizes TWINSHELL CONCEPT AIRFLOW CONCEPT CONNECTS THE LOWER INJECTED SHELL VENTS STRATEGICALLY PLACED VENTS MAXIMIZES AND OVERSIZED INTERNAL EPS CHANNELS TO AIRFLOW AND HEAT EXHAUSTION INCREASE AIRFLOW IN ALL CONDITIONS IN ALL CONDITIONS SOUND SYSTEMS OO A Warning TR ONIL For use with Salomon snowsports helmets only Headphones used in snowsports may cause the skier rider to not hear other skiers riders This can lead to an accident and possible injury or death Always stay in control Skiers Riders downhill from you always have priority so it s your priority to make sure you avoid them Headphones will also restrict your Drift and Lily models only ability to hear what your edge edges are doing on the snow and may distract you They may distract you from focusing on skiing or riding safely which may lead to less control Care and handling The earpad sound system is built to handle cold snowy conditions However this system is not waterproof Do not submerge the Earpad or cord in water or any o
57. ension with corner radius of less than mm asymmetrical shape of the toe sole The boot heel Check for debris lodged in the sole scraped or improperly canted boot sole cut outs in the heel sole that catch on the entry pedal cut outs in the sole that impede proper brake function Note If you are uncertain of boot compa tibility perform the Clean vs Lubricated test Boots that fail this test or violate any of the above points should not be used with any Salomon binding 36 The ski Check for mounting screws protruding through the base delaminated sidewall This can be detected by running your fingers along the sides of the ski base plate flush with ski surface delaminated topskin pre drilled holes Bindings shoul d not be installed on skis that have already been drilled for three or more sets of bindings The binding The toe piece Check for stripped loose or missing screws condition and location of the AFD ripped loose imbedded dirt boot sole pattern tread imprint etc condition of anti friction inserts where applicable missing or unreadable adjustment indicators and missing windows bent or broken base plate principal axis or housing stripped or jammed toe height and cup adjustment screws jammed release adjustment other visible wear The heel piece Check for stripped loose or missing screws improperly installed brake
58. ent in a forward position entering the curve increasing power on skis Provide support and power to skiers in a rear position while getting out of the curve rebound effect the more powerful the rebound the more back support you need to control your skis BACKBONE SCREW ADJUSTMENT Take out the liner Drill the hole in the backbone screw 6 2mm Dismount screw and backbone Dismount internal and external canting Take out the cuff Drill the shell 8 2mm Push in the insert into the shell Mount cuff canting backbone screw Screwed the tall screw RACING KIT Shin plate fig 9 Used to reinforce the forward support and stiffens the flex The height and lateral position are adjustable Choose the forward or internal position and use a 55 mm drill bit to drill the Ist hole in the cuff where marked the shin plate is marked by a cross inside the cuff of the boot Choose the desired height and attach the plate using the T insert and bolts provided Align the plate correctly and use as a guide to drill the 2nd hole and attach as shown Rear spoiler fig 10 The rear spoiler from the performance kit increases rear support with 3 height settings and forward lean by 2 Choose the desired height and attach using the screw provided in the pre drilled hole Delta H lift fig 11 The 4 mm heel lift from the performance kit can be used to improve instep heel h
59. ery careful if you need to use a pushing machine on the Kaprolene areas and NEVER push on the side areas where Kaprolene meets the PU shell 53 3 GENERATIONS OF CUSTOM SHELL 157 GENERATION 2008 In mold Technology Lateral forefoot zone base of the shell 2 GENERATION 2 2009 Dual Injection Technology Complete forefoot zone ankle heel 277 3rd GENERATION cuero OF CUSTOM SHELL TECHNOLOGY MAXIMISE PERFECT WRAPPING WITHOUT PRESSURE POINT MIXED WITH SOFTER PU DYNAMIC FIT ENHANCE STEF IN amp 5TEP DUT UNMATCHED SAME CUSTOM SHELL PROCESS AS USUAL DO 4 6 CUSTOM CUFF On X Pro models you can also have a Custom Shell process on the Custom cuff Process is the same as Custom Shell and Custom Cuff is compatible with cool pack which is covering this area as showed on picture Custom Shell Cuff az compatibility In order to increase Custom cuff deformation it s possible to use racing rear spoiler available as Spare parts ref 5892804 and 4051203 54 THE CUSTOMIZABLE AREA 3 GENERATION 2012 Dual Injection Technology Complete forefoot zone ankle heel 360 CS is only available onthe MAX and PRO Series products X MAX QUEST MAX GHOST MAX X PRO LINER FORMATTING PROCEDURE FOR QUEST MAX 130 1 Put on client s boots in the ambient tem perature of the store the client must have the sens
60. he tab for the version without arrow Re insert the boot to check the adjustment line up within the scribed area of the heel housing JUNIOR RENTAL SC amp SR as py te With screw adjustment With the boot in the binding closed position adjust the forward pressure to align the top of the head screw with the back of the heel part X12 amp X16 33 Tm R E A L cH 1 y e 3 d CLASSIFY YOURSELF DETERMINING YOUR SKIER TYPE IS YOUR RESPONSABILITY Your Skier Type height weight age and boot sole length are used by the shop technician to determine the release retention settings for your bindings Consult these descriptions to select your classification Be sure to provide accurate information Errors may increase your risk of injury 34 Cautious skiing on smooth slopes of gentle to moderate pitch Skiers who designate themselves as Type I receive lower than average release retention settings This corresponds to an increased risk of inadvertent binding release in order to gain releasability in a fall This type also applies to entrytevel skiers uncertain of their classification Skiers not classified as Skiers who designate themselves as Type H receive average release tetention settings appropri ale for mast recreational skiing Fast skiing on siopes of moderate to steep pitch Skiss who desgnate themsalves
61. hin comfort The wide ankle area positioned at the back of the leg and metas covers all the critical foot comfort zones XFit Comfort comfortable single layer constructed thermo moldable liner with a customizable tongue area for shin and ankle comfort Biovent breathable liner in a ski boot to keep feet warm all day This technology helps regulate body temperature thanks to a multilayer construction inspired from apparel Wool Metal Wool metal insulated liner is a mix of wool and a metallic polyeter layer to keep feet warm 51 52 Women s liner with anatomic tongues made of highly moldable foams for better shin and instep comfort in sensitive foot zones WOMEN S SPECIFIC FEATURES fig 1 1 Loop on tongue Easy to bring 2 Specific tongue Autofit and CustomFit foams for better shin and forefoot comfort 3 Fur For extra comfortable and warm liners 4 Thermoformable liner For a better personalisation 5 Quilting anodized PVC For more warmth Calf adjustment fig 2 gt fig 5 only one screw turn to enlarge the upper cuff up to 1 to fit all legs shapes easily and quickly Women cuff opening is adjustable Cuff is delivered with opened position which allows a large volume for calf It is possible to reduce the calf volume by turning the screw present on the cuff Cuff opened maximum calf volume Cuff closed minimum calf volume Cuff ope
62. hoto 4 8 To take the toe off the track Place the toe on the A position of the position indicator Unclip the position indicator with a flat Salomon screwdriver photo 5 Depress the manual toe adjustment button this way the toe can slide forward off the track 40 Ti y i i i Tum S gt O SYNCHRO CENTER Binding to boot adjustments without using the Synchrosysteme Easy glide manual heel adjustment Position the boot in the toe piece With one finger simply lift the adjustment loop at the back of the heel and Slide it forward until the binding cup contacts the boot heel Release the loop push boot down and check the forward pressure adjustment To do this you should see a little metal guide in the indicator fig A Note If a correction is necessary reopen the heel to move it and then re check Wing adjustment Follow the procedure Rental toe height adjustment Follow the procedure Release value adjustment All Salomon rental bindings must be adjusted by using the Adjustment chart Rental visual and mechanical inspection Whenever a binding looks particularly dirty or if visual inspection reveals that something may be wrong with the system the system should be cleaned lubricated and subjected to mechanical inspection SYNCHRO CENTER Lines on the heel guide F JE 5 Position of the toe for
63. ing the heel track and the area under the open heel cup 5 Replace the heel on the track 6 The brake is removable to facilitate ski maintenance T Store in a cool dark ventilated place Position of the heel for a lengh 302 mm White triangle on the heel housing ety fe ity io 5 e ES 41 RENTAL INSPECTION AID FOR APPLICATION OF ISO 13993 concerning rental ski shop practice Sampling and inspection of complete and incomplete alpine ski binding boot systems in rental applications this supplement does not replace ISO 13993 To keep your rental equipment in good condition while minimizing liability we recommend the following program this comes out of the ISO 13993 standard RENTAL INSPECTION SUMMARY Since it is impractical to perform a full inspection each time a system is rented a routine of preseason and inseason inspections has been developed to verify release indicator accuracy confirm correct equipment function and assure proper assembly and adjustment procedures by the rental shop Staff Fully implemented the procedures that follow provide rental shop customers a standard of care equivalent to that provided retail shop customers under current ISO and ASTM standards PRESEASON INSPECTION Preseason inspections are performed on components of the release system bindings and boots All rental bindings new and used are visual
64. ing a dust free cloth wipe off the excess Araldite to obtain a smooth even surface Let it dry for 30 minutes The repair is finished photo A12 12 THE TPP TOP SURFACE All the adult and Rental models are protected by the TPP Transparent Polyamide Protection Regarding the Junior models they are protected by TP Transparent Protection The transparent tops cover the cosmetics underneath which guarantees the durability of the cosmetics BASE REPAIRS Superficial scratches Machine tuning will make the scratch disappear see the ski maintenance repair Not very deep scratches or marks to be filled by machine Pour the polyethylene Wait 10 minutes for the material to harden Remove the excess polyethylene with a steel spatula for a flat surface Proceed with machine tuning Deep cuts Cut out the damaged area with the base patch die Cut a piece of the base material with the base patch die Glue it into the damaged area Hold it in place with a clamp and press repair glue the pieces with Loctite 406 or slow Araldite Proceed with machine tuning REPLACING THE TIP PROTECTOR TIP PROTECTOR WITHOUT SCREWS TIP PROTECTOR WITH SCREWS Triangle tip protector fig B Triangle tip protector fig E Hexagonal tip protector fig C Hexagonal tip protector fig F 1 Insert the tip protector on the ski 2 Place the 2 screws in
65. inside and proceed with riveting REPLACING THE BUCKLE AND OR FOREFOOT BUCKLE TEETH 1 Remove the liner 2 Drill the rivets in the buckle or the damaged buckle teeth 3 Remove the damaged buckle or the buckle teeth and the rivet Save the washer 4 Put in a new buckle or buckle teeth and attach with a rivet or T nut Using a rivet Use a new rivet and the original washer and proceed with riveting Using a T nut Put the threaded insert into the rivet hole from the inside of the boot Put the buckle in place and tighten completely The prongs on the threaded insert should be completely imbedded in the material TO REMOVE THE LINER Turn the clip on the inside of the liner 1 4 turn with a screwdriver 71 NOTIONS OF ANATOMY A basic knowledge of anatomy of the foot is essential if you are going to understand and solve your customers problems and needs since each foot is unique 1 THE BONES OF THE FOOT fig 1 A POSTERIOR TARSUS 1 Calcaneus 2 Talus Astragalus 3 Trochlear surface B ANTERIOR TARSUS 4 Navicular bone Tarsal Scaphoid 5 Cuboid bone 6 3 cuneiform bones C METATARSUS 1 5 metatarsal bones D TOES 8 14 phalanges WHEN WEIGHTED fig 2 When the foot is weighted standing position it can change in size lengthwise it can get 5 mm longer widthwise it can get 12 mm wider When the foot is flexed we notice the circumference of the ankle increases about 2
66. is the benefit of Custom Shell versus the Custom Fit Should you do it before or after The work done on the shell must be done before This will solve problems and last over time The molding of the liner must be done after in order to put the finishing touches on the fit How do know when the plastic is warm enough It is the same process as usual when done with a manual test What is the ideal temperature to form the Custom Shell 80 at core of the plastic How many years of R amp D did it take to develop the Custom Shell technology 3 years Which is the impact of the new material on the performance of the boot There is no effect because the material has the same PU base as a normal boot The boot has exactly the same behavior on snow On the other hand once a boot is fit with the Custom Shell precision is increased If a customer wants an injected liner should it be done before or after In general injection is done before work on the shell usually put normal boots in the oven how is Custom Shell different The normal plastic is going to change very little and comes back to the original position more often The deformation is thus quite low Why is Custom Shell not used in World Cup In World Cup races one person is dedicated to each racer everything is done by hand and each pair is adapted to each discipline Then you could say having Custom Shell is like having your own race technicia
67. ll choose one size higher MAINTENANCE RECOMMENDATIONS Use a damp cloth to clean the measurer It is prohibited to use chemical agents hot water pressurized water gasoline alcohol detergents solvents or aerosols which could permanently damage the plastic materials and erase the marks USA UK EUR Women s Mana Women a USA MP UK THE MEASURER SIDAS SALOMON This measurer allows measures of Length real Mondopoint french sizes UK sizes US sizes ae AA ar WE x 49 tus 1 i E E E Solomon LINER TECHNOLOGIES WE NEVER STOP IMPROVING OUR LINERS THE CHALLENGE IS TO GET THE PILLOW EFFECT IN OUR BOOTS DAY AFTER DAY A VARIETY OF LINER CONSTRUCTIONS FROM INSTANT COMFORT TO HIGH END PRECISION AND A MIX OF INNOVATIVE TECHNOLOGIES FOR WARMTH FIT THERMOFORMABLE FOAM FOAM lt PERFORMANCE PERFORMANCE Every foot deserves to be warm and comfortable _____ 50 This measurer allows measures of Length US Sizes UK Sizes French Sizes real mondopoint Width measured in mm this value linked to the foot length can give an indication to help for the choice of the boot last N Narrow feet Boot last between 95 and 98mm S Standard feet Boot last between 98 and 102mm Wide feet Boot last between 102 and 106mm FEET ME
68. lled holes photo A1 2 Use a crisscross screwing pattern and insert each screw until nearly seated Do not tighten until all screws are in place photo A2 he base plate of the AFD should be flush with the base plate of the toe piece Z AND TOES 1 First pull the center mounting hole sliding track out from the binding far enough to insert the screw into the ski photo A3 2 Tighten the screw until it is firmly seated and hold the toe to keep it from rotating on the ski 3 Next slide the toe piece towards the seated center screw until the two rear screws align with their respective holes photo A4 4 Tighten the rear screws until they are firmly seated 5 Make sure the toe is screwed tightly to the ski The top of each screw should be flush with the base plate HEEL PIECE Place the heel over the prepared holes and tighten the screws using a crisscross screwing pattern SKI BRAKE 1 Do not compress the ski brake before installing it 2 Place the two metal tabs on the front of the brake into the slots in the heel base plate fig A5 3 Rotate the rear of the brake downwards to start the screw in the track 4 Tighten screws with a handscrewdriver 4 Nm maximum photo A6 Note The brake can be removed to facilitate ski maintenance To remove it turn the center screw toward the left and remove the brake SPECIAL BRAKES Special brakes for fat skis are available see Spare pa
69. lomon rental binding must be The Rental products are usually intended to remain under the control of the Certified Rental Dealer Therefore they can be shipped without instructions or individual packaging However if these products are in fact sold you absolutely have to supply your customer with the The bindings that are compatible with the Synchrosysteme are the following 712 SC 710 SC L10 SC L 9 SC 110 SR L7 SC L7 SR appropriate instructions Upon request Salomon will supply you with a document containing important information T5 SC C5 SR The Synchrosysteme can be used with all standardized boots AFTM DIN ISO from all brands The measuring device can be used if skiers come in the shop with their boots on visually inspected for compatibility To use the Synchrosysteme you need Synchrosysteme jig references 001003 and 001040 adjustment tool reference 000902 JIG SELECTION JIG 001003 A single mounting jig for Adult and Junior skis with the following positions Adults sizes 22 34 for skis gt 140 senior SynchroR junior Junior sizes 16 26 5 for skis 80 140 cm Jig mounting position selection Example Senior Synchro Center position eynchrU junior Quadrax 3R A RENTAL BINDINGS JIGS POSITIONS 001003 amp 001040 Synchro C Senior Synchro R Senior Synchro C Junior Synchro R Junior Quadrax 3 260 lt gt 382 268 lt gt 3
70. ly inspected and then tested using specially selected Reference Boots Bindings that fail go through a troubleshooting procedure to identify and correct the deviation or malfunction If this procedure does not correct the problem the binding is removed from inventory All rental boots new and used are visually inspected for damage wear contamination broken or missing parts or inferior materials at contact points with the binding In addition one boot per cell is tested for boots that are new to the rental inventory A cell is all boots of the same make model age and shell size random selection of 596 of all boots previously accepted into inventory is also tested Tests are performed with a test device and a pair of specially selected reference bindings If a boot fails all boots from that cell are then tested Boots that fail and cannot be repaired are removed from inventory 42 INSEASON INSPECTION Inseason inspections are performed on complete rental systems to ensure that the equipment is adjusted appropriately and continues to function correctly Typically 5 of the rental inventory is tested during each two weeks sampling period The random sample is equally divided between equipment that is available for rental and equipment that has just been rented The equipment in the as rented category is from real skiers in the condition in which it is either dispatched or returned while the
71. n ADJUSTMENTS AND PERSONALIZATION WORLD CUP CLAW STRAP Increases cuff fastening a more powerful fastening for a better envelopment than a traditional strap More reliable it can t open while flexing the boot both before and during the curve BACK BONE Increases the junction between cuff amp shell for flex management in a forward position entering the curve increasing power on skis Provide support and power to skiers in a rear position while getting out of the curve rebound effect the more powerful the rebound the more back support you need to control your skis OVERSIZE PIVOT Oversize pivot is screwed and could be disassembly in order to take out the cuff from the shell for bootfiting specific key is provided with the boot for this operation For reassembly the oversize pivot should be tight at 5 5 Nm torque value CANTING Canting could be adjusted by following operations by an approved Salomon technician Internal boot sole grinding fig 1 Chassis grinding which should be conform to the 150 5355 after the operation TECHNICAL DESCRIPTION X LAB MEDIUM Energizer 140 World cup advanced shell technology World cup shell Last 95 Racing kit 1 My custom fit World Cup liner 2 PU either lower shell and cuff 3 Oversized pivot 4 Back bone 5 World cup claw strap 45mm RACING KIT Rear spoiler fig 2 The rear spoiler from the performance kit increases rear
72. ned Cuff closed amp a HOW STEPS TO FOLLOW FOR A SUCCESSFUL CUSTOM SHELL CUSTOMIZATION We recommend the use of the Sidas bootfittingoven Make sure the customer uses only ski socks which go higher than the top of the boot 1 Remove liners from shells 2 Put the shells in the oven with buckles open 3 Close the door and start the machine set the timer for 10 minutes Make sure to wear insulated gloves when removingboot shells Do not allow customers to touch the boot avoiding possible burns 4 Switch off the oven and remove the shells 5 Put liners back in 6 Help the customer to step in 7 Close the boots with minimum tightening first tooth of the buckle and make sure the forefoot shell seals stay in the right position Ask your customer to stand still Avoid bending or walking with warmed shells 8 Make sure the shell has been fully deformed before starting the cooling process It takes approximately 2 min 9 Cooling process you can find 2 sizes of cool pack first one for boots sizes 22 to 4 26 5 the second one or boots sizes 27 to 31 5 thanks to follow the process CUSTOM SHIELEL 10 Take boots off the custom Shell boot is ready You can use your regular heating tools though they would be less practical than the oven heating elements gun boiling water Kaprolene has been created to be deformed by the foot s natural pressure Be v
73. ng Procedures following a Failed Inseason Inspection 10 Record the date the sample was tested the number of units tested the number of Class and Class or Deviations whether the sample passed or failed and any actions taken There is no need to record the identity of units tested or actual Test Results Chart B Sample Size Inventory Size 100 200 300 400 500 600 700 800 900 Sample Size Units 16 20 30 40 Maximum Class Dev 3 4 6 8 50 60 10 80 80 45 BROKEN MOUNTING SCREW Salomon screw extractor kit it comes with two bits of different lengths The longer bit is for use with the Salomon jigs for adult skis The shorter bit should be used with the Salomon jigs for junior skis The procedures for using both bits are the same When a screw or tap breaks in a ski it must be removed carefully to avoid further damage STRIPPED SCREWS For a stripped screw use the repair kit 000878 For this operation use the corresponding jig and position it properly by lining it up with the hole to be repaired Follow this procedure 1 Fit the extractor drill bit into the electric drill with the shoulder touching the chuck 2 Fasten the appropriate jig onto the ski 3 Position the correct jig bushing directly over the broken screw 4 Drill slowly around the broken screw using an up and down movement to let the shavings escape Caution do not hit the screw 5 Continue until the
74. nium is proven with bindings ILS and Mavic wheels According to this experience we defined three levels of strength Aluminium Technology 40 stronger by Salomon Aluminium Technology Al 15 stronger by Salomon Aluminium Technology Competitive by Salomon strength price ratio Composite range We do our pole s shafts the same way that golf companies do their own golf shafts We defined threelevels of Carbon grade e Carbon Technology Ki 80 of Carbon by Salomon Carbon Technolo 40 of Carbon nology xx 40 Carbon Technology C 1596 of Carbon by Salomon 82 RENTAL POLES Salomon designed specific poles for rental adapted to a professional and intense use This warranty will not apply for damages resulting of rental use of poles that was not designed specifically for rental a w JT Y amp di 4 oq ka d AT 145 gt ZEE k pe E i E lt HOW TO CUT AND GLUE POLES POLES SIZING CHART Take off the Grip by soaking it in boiling water Warm up some thermo glue by using a heat and then simply removing it by hand gun And apply warm glue directly on the top of the shaft 165 1 5 160 170 155 165 160 155 150 145 140 Put some tape exactly over the cutting zone 135 Warm up again thermo glue on the shaft with the heat gun Place directly the grip on the shaft 130 taking care that it s weel po
75. od 4 The machine is now available for thermo forming another pair of boots 5 Open the boot buckles 6 The boots must be put on immediately following the end of the 15 min heating cycle T Close the buckles with medium pressure not too tight fig 2 8 Close the strap more firmly 9 Tap the heel on the floor to make a good impression of the Achilles heel 10 Wait 10 min in a standing position If you feel any discomfort whatsoever when stepping in take your boots off immediately 11 Remove the boots PRACTICAL ADVICE Salomon recommends that no CustomFit liner be thermoformed more than three times To optimize the results of the thermoforming process it is recommended that you make several flex movements during the 10 minute cooling process to simulate the anklebone movements when skiing gt It is recommended to wait 1 2 hour before skiing with the boots to allow for complete stabilization of the thermoformed liner Drying with a machine When drying the CustomFit liners with a drying machine it is important to respect the drying time recommended by the manufacturer and that the temperature not exceed 40 QUEST MAX BC CUSTOM FIT 1 Remove the liner from the shell 2 Remove insoles from the liner 3 Put the liner in the Custom Shell oven 5 minutes at 100 C maximum preferably already heated 4 At the end of the 5 minutes add insoles original custom or orthopedic in
76. of the toe piece Place the boot in the binding closed position Loosen the micrometric screws to loosen the wings Check that the tip of the boot sole is flush against the butt plate fig A2 This contact is made when the boot has lateral play Do not over tighten the boot may no longer be centered 2 Automatic adjustment the wings on the toe cup are self adjusting TOE HEIGHT ADJUSTMENT With the boot in the binding raise the toe by turning the adjustment screw located on top Models Wing Toe height of the toe piece counter clockwise adjustment adjustment Pull the boot back to create a gap between the boot sole and the binding AFD Driver 12 L Lower the toe height by turning the adjustment to BEF meni screw clockwise to obtain the recommended gap ideis a see the following chart 1 2 0 5 For models with automatic wing and automatic height adjustments make forward pressure adjustment C5 only See instructions in following chapteras To po LS Note Always check the forward pressure after 714 lt m automatic automatic making toe adjustments aa 32 FORWARD PRESSURE ADJUSTMENT With tool less and tab adjustment If this adjustment is incorrect remove the boot from the binding With the boot in the binding closed position make sure the lift the adjustment tab to slide the heel into the desired position arrow The extremity of t
77. old and put the skiers weight forward for faster initiation Remove the liner and position the wedge in the hole provided in the rear of the Custom Sole Softening the boot fig 12 Two methods exist to soften the boot The reversible method Remove the canting lock screws Insert the plugs provided in the holes The non reversible method This involves cutting out the marked V shape in the lower shell and should be performed by your specialised Salomon dealer 59 TECHNICAL DESCRIPTION X PRO 120 1 360 45mm strap 2 4 micro alu buckles 3 Articulated sensifit 4 360 Custom Shell 5 24mm oversized pivot 6 Flex adjuster T My CustomFit 3D Race liner FEATURES ACCORDING TO DIFFERENT MODELS ADJUSTMENTS AND PERSONALIZATION CUSTOM SHELL 360 INCLUDING CUFF maximized customizable areas Complete wrapping without pressure points Dynamic fit enhance CUSTOMFIT 3D Thermoformable inserts around ankle amp heel Solve instant pressure points around ankle amp heel OVERSIZED PIVOT Reduces play for precision amp direct transmis sion Twinframe technology the right rigidity where it s needed Top pad grinding not over FLEX ADJUSTER reference line taht is to say Articulated sensifit fig 1 amp 2 CANTABLE ALPINE PADS Available as spare part cantable alpine pads Bottom pad grinding are compatible with following models XPro a parallel to top grin
78. omer service in your country Do not take the machine apart This machine is for exclusive use with Salomon CUSTOMFIT liners Any other use is forbidden PREPARING FOR USE fig 1 1 Remove the machine from its box and place it on a flat surface Verify that the voltage used is the same as indicated on the machine 2 Lift the hood 3 Lift the nozzles using the handles provided 4 Close the boot s buckles and slide the boots onto the nozzles Make sure that the top edge of the boot touches the obturator Important Any insoles used other than the ones received in the boots at the time of purchase should be removed before the heating procedure begins Re install them after heating to mold the liners 5 Mter having read and understood the machine s instructions especially those on safety you can now plug the machine in STARTING THE MACHINE Set the timer for 15 mins Warning For optimal results it is important that the heating process lasts 15 minutes Using the machine for more than 15 mins can damage the liner operate the machine with both boots in place PUTTING THE BOOT ON 1 When thermoforming you should only use ski socks that have the following characteristics socks that go higher than the top of the boot Socks with at least 45 wool Wearing normal low cut socks could cause skin reactions to the heating process 2 Remove the boots from the machine 3 Close the ho
79. ow thin this part is Solutions for Falcon X Wave Performa Special precautions are required when stretching the shell the inside and outside of the cuff and lower shell simultaneously so that both will be at the same temperature despite their different thicknesses and layers Place the stretching device on the inside close the boot during the stretching operation and proceed with very small successive degrees of stretching to avoid creating a space between the cuff and the shell Falcon and X Wave Be careful not to heat the metal parts there is a risk of damaging the plastic Solutions for Rear Entry models Remove the insole to increase the volume Stick a C shaped foam pad in the area around the ankle bones on the liner fig C Remove some foam from the liner in the area around the ankle bones Add shims to blue heel envelopment plate Solutions all products Stick a chevron foam pad in the form of an inverted V above the calcaneus to push the foot forward in the shell and reduce the pressure on the heel fig D It is possible to remove some PU from both sides of the Achilles tendon on the cuff grinding and or on the lower shell Falcon X Wave Ellipse and Performa Caution The boots whose lower shells aren t made of Polyurethane PU must not be stretched with heat there is a risk of damaging the material 74 PROBLEMS HEEL MOVEMENT
80. pping When in doubt about the ski s core composition select a 3 6 mm diameter bit and drill one hole to see if any metal comes in contact with the bit If contact is made with metal re drill with a 4 1 mm bit 2 Drill through the jig s proper bushings applying moderate downward pressure on the drill Make sure that the countersink bevel on the drill bit has properly deburred the hole 3 drilling turn the ski over and hit the base several times with the palm of your hand to remove any debris from the drilled holes DRILLING JUNIOR SKIS Use an 8 mm length drill bit to mount the Junior bindings L7 L7SR T5 T5SC amp SR C5 C 5 SR Easytrak 17 amp C5 Whenever junior bindings are mounted on adult skis there is an increased possibility for binding pull out due to poor screw retention The penetration depth of junior screws into the ski core is only 6 mm If necessary use adult screws and drill bits to penetrate any mounting platform For bindings mounted with adult binding screws the penetration depth is the same You must drill a hole deep enough to accommodate the screw length you are using or damage to the ski base may result TAPPING Tapping is usually done when the binding screw will come into contact with metal or in the following cases the material is too hard for a screw when the screw insertion would distort or stress the material holding the screw when recommended by the ski manufact
81. r base plate and high back of certain snowboard bindings SALOMON provides a lifetime warranty applicable for base plate and high back of the limited following snowboard bindings Caliber Chief Relay Pro Series Ring Absolut Pure Premium Cypher Arcade Patriot Stella Celeste To the extent permitted by national laws the Warranty Period will not be extended renewed or otherwise affected due to subsequent resale repair or replacement of the Product However part s repaired or replacement product s during the Warranty Period will be warranted for the reminder of the original Warranty Period provided replacement repair has been performed by SALOMON or an authorized SALOMON retailer Depending on the country particular and variable Warranties Periods may apply in relation to applicable legislation Nothing in this warranty policy can exclude or limit these statutory provisions 11 THE WARRANTY DOES NOT COVER Damages due to transportation Damages due to storage Damages due to improper use of the products and poor maintenance Damages due to non observance of the instructions or restrictions for use of the products as defined in the products owner manual Damages due to the products normal wear and tear Damages due to non observance of the instructions for maintenance as defined in the products owner manual Damages due to modification of the products Damages due to any
82. re test If the system still falls outside the in Use range perform the Clean vs Lubricated test TEST FOR ELASTIC TRAVEL AND RETURN Laterally fig 1 Secure the ski Hit the forefoot area of the boot with a rubber hammer Use sufficient force to move the boot off center but not hard enough to release the system The boot should move off center at least 5 mm and return to center within 2 mm of its original position Vertically fig 2 Put the boot in the binding depress the heel lever while pulling forward on the upper cuff of the boot until the boot heel lifts at least 5 mm Release both hands simultaneously The boot should go back in place quickly and smoothly This check can be performed either manually or by using a mechanical device If a measuring device is used follow the recommendations of the test device manufacturer for proper procedure RELEASE VALUE WITHIN SPECIFIED RANGE AND BOOT BINDING COMPATIBILITY Testing of release values with a test device is recommended fig 3 If a test device is not used the skier should be informed In addition the skier must be warned about the risk of possible breakage of boots and bindings that have been subjected to shocks or abnormal stress Test the toe First exercise the toe by releasing it once in each direction Then using test device measure and record the twist release value in each direction The measur
83. rms Wide brake Plates For all other parts such as AFD housing brakes crews please consult your spare parts catalog 1 Heel lever 2 Indicator window 3 Brake pad 4 AFD plate 5 Height adjustment screw 6 Heel cup axis T Heel cup 8 Release adjustment screw 9 Lenght adjustment 10 Heel housing 11 Heel plate 12 Brake arms 13 Wings toe adjustment PROPER PROCEDURES Proper procedures to be used while mounting and adjusting Salomon bindings are the following steps 1 Mounting bindings 2 Binding to boot adjustments 3 Release value selection and adjustment 4 Final checking visual and mechanical inspections 5 Skier instruction and warning Important before drilling the ski it is important to determine that the boot you are using will be compatible with the binding Only boots that conform with ASTM DIN German Industrial Norm or ISO International Standard Organization boot sole standards should be used with Salomon bindings boot sole must also be flat and in good condition MOUNTING MOUNTING BINDINGS 1 Remove shrink wrap from skis 2 Drill the skis using the appropriate jig and drill bit as shown in the chart opposite Make Sure that the jig is parallel to the ski during the entire drilling process fig 1 3 Follow the ski and binding manufacturers mounting instructions closely It is necessary to use Salomon glue or Epox
84. rnish it or add any coloring products After receiving an impact the helmet may be damaged on the point that it is no longer adequate to protect the wearer s head against further impacts Even if the damage is not visible it is necessary to replace the helmet STANDARDS Salomon helmets respect the following standards CE EN 1077 helmets for alpine skiers C and for snowboarders ASTM F2040 helmets for recreational snow sports Non motorized winter sports Main tests of norms fig 1 SHELL CONSTRUCTION In order to meet consumer s needs in terms of safety head hold and comfort Salomon uses 4 construction technologies They provide performance in terms of resistance absorption deflecting impact and resisting penetration Hybrid construction Combination of in mold lower shell for reduced weight with injected upper shell for more durability and to accommodate mechanical ventilation devices In Mold construction an external PC layer molded together with the EPS cap to provide the best ratio lightness resistance to the helmet This technology is commonly used by every helmet manufacturer Twinshell construction a lightweight in mold shell mounted on a durable injected basis offering a brand new airflow ventilation system Injected construction an external cap made of ABS combined with an internal cap made of EPS MY PERFECT FIT VENTILATION Fit foams All our models are ben
85. ront slide backward A the complete heel piece and readjust the heel piece s position B 5 Step in the boot and and check forward pressure as described above 8 7 Mounting and adjusting procedure 29 THESE ALPINE BINDINGS ARE INTENDED BE USED ONLY WITH THE FOLLOWING SKI BOOTS Alpine ski boots compliant with ISO 5355 standard AND Ski boots equipped with WTR technology labelled kit of walking soles for touring skiing Any use with other ski boots could cause the ski binding boot system to be faulty and affect release characteristics which would increase the risk of serious injury while skiing Therefore skiers are warned not to use this product with any ski boots other than those meeting the standards indicated above Skiers are advised to consult the dealer where this product was purchased or an equipment specialist at any SALOMON authorized ski dealer of this product for further information regarding which ski boots meet the standards listed above MOUNTING amp ADJUSTING PROCEDURE 1 Use the Salomon mounting jig ref 32981601 and drill the skis following the ski and binding manufacturer s X instructions Mount the toe piece and the rear plate on the ski by tightening the screws at 4 N m check if rear plate is correctly mounted 2 Assemble the ski brake with the heel piece 3 From the center of ski insert the heel piece on the rear plate and adjust at the mid position with a
86. rts catalogue 19 RETAIL SPECIAL CASES IN MOUNTING amp ADJUSTING SMARTRAK TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY CONTENTS OF THE BOX 2 Toes mounted on a sliding part 2 Heels mounted on a sliding part 2 Brakes 2 Thin Plates gt 1 Notice ere Le L MOUNTING 1 Insert the Thin Plate in the seating ahead the plate fig 1 2 Place it correctly with a rotational motion fig 2 3 From the rear slide the Toe piece on the interface until it corresponds with or is just above your boot sole length using the manual lock to authorize the sliding fig 3 amp 4 4 From the rear slide the Heel piece on the interface until it corresponds with or is just above your boot sole length using the manual lock to authorize the sliding fig 5 Mount the Brake following the usual procedure fig 6 ADJUSTING EXAMPLE 6 Identify the length of the boot 7 If you have boot sole L 306 mm adjust the Toe on the 308 mm mark The range in this case is 301 mm to 308 mm fig 7 8 If you have chosen the L 306 mm adjust the Heel piece on the 312 location The range in this case is 305 mm to 312 mm fig 8 9 Step in the boot and check forward pressure fig 9 The arrow on the housing must be within the scribed area al al ie 20 SMARTRAK GRIP GRIP PLUS CONTENTS OF THE BOX
87. s of the base and materials available Grind entire base surface photo 1 b Fill in scratches with base repair material Repair any large damaged areas with base patch die STONE GRINDING For Prolink skis install the Binding Bridge kit according to the Maintenance specifics paragraph A SURFACE SMOOTHING Place the skis on a flat surface Eliminate any excess polyethylene on the base with a hand base plane to decrease the risks of contaminating the stone B SEMI FINISHING Stone grind until the base becomes flat and glossy Avoid overheating and use of a dirty stone lengthwise streaks on base are from stone contaminant Dress the stone regularly to keep it in good condition when using a belt grinding machine use 80 grit belt C FINISHING PHOTO 2 La Stone grind to obtain a fine structure when using a belt grinding machine use 150 grit belt Do not use a dirty stone which creates fluff hair D BEVELED RECESSED FINISHING For skis with beveled recessed finishing we recommend a straight fine stone ground structured base Note always make the last run in this direction Tip Tail Concerning the machine parameters please consult the machine manufacturer 27778 a n N j 7 nad Ji ee ee B di Td mm RR UU XC X M H
88. screwdriver 30 Step in the ski boot in the binding check and adjust the forward pressure 5 Select and adjust the setting release gt values for toe and heel pieces 6 With the screw on the left side of the gt toe piece adjust the toe wings to come in contact with the ski boot see ADJUSTING WING ADJUSTMENT gt p32 7 Adjust the toe height with the adjustment screw until to create a gap of 0 5 mm between the boot sole and the binding see ADJUSTING TOE HEIGHT ADJUSTMENT gt p32 31 RETAIL FAT SKIS Refer to the spare parts catalog to know which jigs and brakes to use according the different ski widths and binding models The reversible pads allow the jig to adapt to different ski widths fig 1 Procedure for changing the pads to the other side 1 Pull the pad off the arm of the jig 2 Change the pad to the desired position 3 Insert the pad into the arm of the jig 4 Repeat this procedure On the other 3 arms for mounting the bindings symmetrically ADJUSTING Once the binding has been mounted it is necessary to make the proper binding to boot adjustments All Salomon bindings may be closed manually by simply lifting the heel lever Adjustments must be re checked every time boots are changed Use the following procedure WING ADJUSTMENT 1 Manual adjustment fig A1 only one adjustment screw which is located on the left side
89. sired position 20mm and tighten the screw TECHNICAL DESCRIPTION MISSION 70 1 Sensifit liner wings 2 Strap 35 mm 3 Tool free catch adjustment 4 Pads 5 Micro adjustable buckle 6 Adjustable spoiler T X Fit Fusion Advanced liner FEATURES ACCORDING TO DIFFERENT MODELS 61 BOOT CONCEPTS SSS SSS SS SS SS SS SS SSS SS eS SSS eS SS QUEST MAX ADJUSTMENTS AND PERSONALIZATION OVERSIZE PIVOT Oversize pivot on QUEST MAX 130 is screwed and could be disassembly in order to take out the cuff from the shell for bootfiting A specific key is provided with the boot for this operation For reassembly the oversize pivot should be tight at 5 5 Nm torque value CANTING The oversize pivot doesn t stand for canting adjustment Canting could be adjusted by internal boot sole grinding by an approuved Salomon technician Boot sole grindin INTERCHANGABLE SOLE PADS Possibility to change from a DIN Alpine to walking sole pads please read the concerned chapter 62 TECHNICAL DESCRIPTION QUEST MAX 130 1 Lacing system in option 2 Waterproof gusset 3 Magnesium buckles 4 360 Custom Shell 5 24 mm oversized pivot 6 Backbone release 7 My CustomFit Race liner 2 loops FEATURES ACCORDING TO DIFFERENT MODELS TECHNICAL DESCRIPTION Energizer 120 1 Cushioning system tongue and heel pad 2 Forward pressure plate 3 Last 100 4 Extended rubber sol
90. sitioned compared to the basket 125 120 Cut the shaft exactly where you need by using a saw and cutting directly on the tape This will enable the delamination of the carbon fiber Remove the tape and use sand paper to clean remaining dust of carbon 83 HEAD OFFICE SALOMON S A Siege social Metz Tessy F 74996 Annecy Cedex 9 Tel 33 0 4 50 65 41 41 Fax 33 0 4 50 65 42 56 334506542 57 SUBSIDIARIES DISTRIBUTORS ARGENTINA Winners Productos deportivos S A Tel 54 115 256 5000 AUSTRALIA Tel 61 3 8586 6666 AUSTRIA Tel 43 662 45 55 47 100 BELARUS Sport El gance Tel 375 172 840 244 BRAZIL Tel 5511 3094 1923 BULGARIA Mtk Sport Tel 359 888 343 427 CANADA Tel 1 905 470 9966 CHILE Grylan S A Tel 562 949 37 17 CHINA Tel 862 168 755 010 CZECH REPUBLIC Tel 420 272 700 963 DENMARK Tel 45 45 565 530 ESTONIA LATVIA LITHUANIA A amp Tova Tel 372 518 95 88 FINLAND Tel 358 207 789 600 FRANCE Tel 33 4 74 99 15 15 DV Sport Tel 995 77 99 11 22 GERMANY Tel 49 0 8000 725 6666 GREAT BRITAIN Tel 44 1276 404 850 GREECE Hellenic Flame Tel 30 23 10 566 269 HOLLAND Tel 31 334 345 070 HONG KONG Orient Fair Development Ltd Tel 85 224 101 952 HUNGARY Tel 361 205 37 70 INDIA Pantaloon Retail Ltd Future Group Tel 911 244 641 302 ISRAEL ETT Tel 972 523 910 882 ITALY Tel 39
91. sole length column and the skiers code row shows the initial indicator setting for the skier Adjust both toe pieces and heel pieces accordingly 6 Caution If the box at the intersection of the skiers boot sole length column and the skier s code row is empty move horizontally on the same row and use the closest indicator setting FINAL CHECKING VISUAL AND MECHANICAL INSPECTIONS A Salomon certified technician must sign or initial the Workshop form indicating that all systems inspections have been performed final check is your quality control measure to verify that all required procedures have been properly completed and involves the following steps VISUAL INSPECTION OF SYSTEM COMPONENTS TROUBLESHOOTING PROCEDURE After the bindings have been properly mounted and adjusted visually inspect the ski boot binding system The boot Check for gross irregularities where the boot contacts the binding and the AFD deformation wear that the boot conforms to the norm DIN ISO or ASTM markings If the boots are not marked check with the Supplier These bindings are not designed to function with boots that do not conform to the norm that the boot has not started to crack or break The boot toe Check for the absence of rubber and or metal tip protectors mold flashings a ramp or bevel in front of the AFD area grid pattern or tread in the AFD area excessive wear a toe sole ext
92. support with 3 height settings and forward lean by 2 Choose the desired height and attach using the screw provided in the pre drilled hole 3 and 5mm Lifters available to be compliant with the ISO 5355 standard after shell grinding Softening the boot fig 3 Two methods exist to soften the boot The reversible method Remove the canting lock screws Insert the plugs provided in the holes The non reversible method This involves cutting out the marked V shape in the lower shell and should be performed by your specialised Salomon dealer 57 TECHNICAL DESCRIPTION XMAX 120 Energyzer 120 1 My CustomFit Lab liner 2 World Cup claw strap 3 Oversized pivot 4 Custom Shell FEATURES ACCORDING TO DIFFERENT MODELS ADJUSTMENTS AND PERSONALIZATION ADJUSTABLE MICRO BUCKLE FIG 1 Fine tune the adjustment by turning the buckle to the desired fit ADJUSTABLE BUCKLE TEETH fig 2 Offers a greater range of lower leg adjustment 20 mm Loosen the screw with a 3mm Allen wrench Tighten the screw and buckle teeth in the new position 58 3D BUCKLE fig 3 The 3D buckle adjustment allows the position of the instep buckle to be changed for personalised foot hold Unscrew the buckle with a 3 mm Allen wrench Position the buckle over the plastic lug on the shell Tighten in the alternate position OVERSIZE PIVOT ON XMAX 120 fig 4 Oversiz
93. t be used by the tech nician to determine the appropriate adjustment for each skier which conforms to the following norms ISO 11088 ASTM F 939 ASTM F 1063 and AFNOR FD S 52 448 documentation fascicle SKIER CLASSIFICATION This classification has to be determined by a dialogue between the skier and dealer which helps to take into account the diverse factors that influence the adjustment These factors are explained in the norms cited above Type I skiers Ski conservatively Prefer slower speeds Ski on easy to moderate slopes Intermediate level but not in good physical condition Good skiers smooth and supple style empha sizing safety Favor lower than average release retention settings This corresponds to an increased risk of inadvertent binding release in order to gain increased release capacity in a fall Type II skiers Intermediate skiers in good physical condition Prefer a variety of speeds Ski on varied terrain including most difficult trails All skiers who do not meet all the descriptions of the other skier types Type III skiers Ski aggressively Normally ski at high speeds Prefer moderate to steep terrain Favor higher than average release retention settings This corresponds to decreased capability to release in a fall in order to decrease risk of inadvertent binding release Type 3 settings should not be used by skiers of less than 22 kg O
94. tenance record if Test Results are within the Inspection Ranges provided in Chart 11 Set the ski aside if the Test Result in any directions of release is outside the Inspection Range in Chart A 12 Follow Troubleshooting Procedure for units which have been set aside and retest if changes in the unit s condition or adjustment are made 13 Record FAIL in the binding s maintenance record if after troubleshooting test results in any direction of release are outside the In Use Range Replace the failed unit and retest before returning the ski to service 14 If after troubleshooting Test Results are outside the Inspection Range but within the In Use Range apply a Correction Factor to the unit and note the Correction Factor for that unit in the binding s maintenance record 15 If many bindings fail check the test device and re inspect the Reference Boot If necessary select another boot and retest the bindings 43 RENTAL PRESEASON BOOT PREPARATION The procedure that follows is an integral part of preseason maintenance 1 Clean all boots with a mild detergent and water and repair or replace damaged or missing parts 2 Visually check a Conformance with ISO and other applicable standards If the boot contacts the binding brake or AFD in areas other than the designated contact points it may be incompatible with the binding product specific figure or description b Boot material
95. terial defects Defect for the Warranty Period as defined below SALOMON Products are compliant with their description and specifications it is your responsibility to ensure that the Products you purchase are compatible for the intended use This warranty is valid and enforceable only in the country where the Product was purchased by the end user provided that SALOMON has intended the Product for sale in that country In European Economic Area countries this warranty is also enforceable in any country within European Economic Area where SALOMON has an authorized importer subsidiary or distributor Please report to the SALOMON authorized retailers list Depending on the country particular and variable warranties may apply in relation to applicable legislation Nothing in this warranty policy can exclude or limit these statutory provisions WARRANTY PERIOD The Warranty Period starts at the date of retail purchase of the Product by the original end user purchaser The product may consist of several different parts and different parts may be covered by different warranties periods please report to Warranty Period The different Warranties Periods are a Three 3 years for winter sports trousers and jackets b Two 2 years for other products Warranty period is two 2 years for alpine ski bindings sold during Fall Winter 2011 2012 and five 5 years for alpine ski bindings sold before Special warranty fo
96. the instructions in the chart below Bootcenter related to the real bootcenter position in mm forward n backward 7 0 mm 20 mm 3 0 mm 0 5 mm 20 3 0 05 20 3 0 0 5 30 mm Toe piece 3 Drill your chosen setup and remove the mounting jig Note The X 12 amp X 16 bindings have an additional hole in the middle to fix the brake don t forget to drill this hole Maximum of positions to adjust the boot center Forward Backward 2 2 3 4 3 2 3 2 2 2 E uL EM mE n LS BEN _ gp Screw to fix the brake LAE RETAIL Z SPEED PLATE TO BE MOUNTED BY A SALOMON AUTHORIZED DEALER ONLY MOUNTING AND ADJUSTING 1 For mounting Z Speed bindings on skis holes have to be drilled with 6 Slide the toe piece from the front backward and the heel piece from the the Salomon mounting jig ref 11139301 to ensure a proper alignment of the tail forward binding 2 Mount the rear plate by tightening the screws at 4 N m T Select the length of the sole boot and adjust the toe and heel pieces at the length corresponding gt gt gt LO o o ool olo NI lt 5 Mount the brake by tightening the screw at 4 N m with tool Torx 25 24 EASYTRAK TO BE MOUNTED BY A SALOMON AUTHORIZED D
97. the ski from the heat press and remove base patch and plastic film 12 Reapply epoxy to the affected area 13 Carefully insert piece of base material into cut out area 14 Cover affected area with mold release paper and place ski in heat press 15 When the epoxy has cured remove the ski from the heat press 16 Grind base and edge locally 17 Plane patch area to obtain proper geometry with base plane or file 18 Repair any damage to top layer with a mixture of epoxy and colorant 19 Tune and wax the ski 14 LIST OF TOOLS AND ACCESSORIES THAT ARE NECESSARY IN THE WORKSHOP Technical manuals for Skis and Bindings Spare parts catalogs Release adjustment table DIN chart Skier type Jigs please consult spare parts catalog for different references Synchro measuring device ref 001189 Electric drill Drill bits see on spare parts catalog for different models Adjustment tool Salomon screwdriver ref 000902 Power screwdriver with torque release Posidrive screwdriver 7mm ref 000862 Tap ref 000816 Brace ref 000817 Repair kit 2 extractor bits and repair plugs ref 000878 16 Grease ref 000905 Glue ref 000811 4 5 diameter plastic plugs different references depending on the color see spare parts catalog Specific adaptations for the references see spare parts catalog Brakes carving long a
98. ther liquid Do not attempt to clean or to disinfect your helmet with the earpad sound system installed CHINGUARD INSTRUCTIONS Small chinguard compatible with Equipe 5 55 56 Equipe JR JRS 51 55 gt Convenience fig 5 Magnetic buckle Large chinguard compatible with Equipe M 56 5 57 5 L 58 59 XL 59 5 60 5 XXL 61 62 Equipe JR JRM 55 59 opens simply by sliding with one hand laterally place on top to close 81 TECHNICAL INFORMATION CHOOSING MAINTENANCE YOUR POLE SIZE RECOMMENDATIONS e _____ Turn the pole upside down with the Use a cloth with soap and water to clean the tip pointing up poles It is prohibited to use chemicals hot Hold the pole right under the basket water or pressurized water gasoline alcohol Your arm will form a right angle 90 detergents solvents or aerosols that can when you have the ideal size permanently damage the plastic materials and erase the cosmetics MOUNTING THE REPLACEABLE BASKETS Salomon has made 1 type of replaceable baskets available to you a Mounting at the same time screw the basket on and push it towards the handle of the pole Removing at the same time unscrew the basket and pull it toward the tip of the pole b Screw the basket on completely until you hear four clicks wear gloves as a precaution POLES TECHNICAL FEATURES Aluminium range Salomon know how in alumi
99. tion storage or not abiding by the instructions for use or maintenance 78 NEW SIZING CHART lt N LS lt e N STANDARD FIT SIMPLE INTUITIVE SALOMON EXPERTISE The helmet is a safety product To ensure an optimal protection comfort and head hold the helmet must be chosen in the user convenient size To choose the good size it is necessary to measure the cranial perimeter of the head in cm from the forehead to the most prominent back part of the head ALLIUM CA PHANTOM CE PHANTOM EDITION CA RANGER CA RANGER CRUISER PROPHET M DOUGLAS CA PROPHET CA HACKER CA PHANTOM RC CA IDOL CA AURA ICON CA ICON PEARL ORIGINS SHIVA CA HACKER BRIGADE AUDIO BRIGADE EQUIPE POISON SHIVA VENOM JIB AUDIO JR EQUIPE JR JIB JR KIANA JIB RENTAL KIANA RENTAL DRIFT ADULTS FIT amp SIZING IN H Ta LO a LN p LO IN ES Ta AN uM inf IN 10 10 10 CO LO L0 L0 tO in 10 00 10 0 JUNIORS amp KIDS FIT amp SIZING IN pi Ta Ho LO E 7 LN a LN E Ta oO o oo ala uM inf IN 10 iN CO LO LO L0 tO in 10 0
100. tion Range provided in Chart A for the Skier Code used to set up the Reference Binding L J or E Repeat the Visual Check on all boots that have been set aside correct any defects noted and retest Remove from inventory boots that fail the retest 10 Check all other boots from the same cell make model year and shell size as those that failed Note completion of the preseason inspection clean the liquid detergent from the equipment and lubricate the binding before returning it to service Mo INSEASON SAMPLING AND INSPECTION The Inseason Inspection is a test of complete systems and all the procedures used by the rental staff to assemble and adjust the system SAMPLE FREQUENCY Random sampling is conducted throughout the entire season Frequency is as follows 1 After 7 days of operation 2 1 the sample passes the next sampling is taken after another 7 days of operation 3 two consecutive samples pass sampling frequency is increased to 14 days 4 sample fails at any time daily sampling is instituted until two consecutive samples pass at which point weekly sampling resumes SAMPLE SIZE Sample size is 596 of inventory but not less than 16 nor more than 80 units as noted in Chart B Sample size is based on average daily output If rental output drops below 50 of capacity over the sampling period the sample size can be reduced proportionately INSEASON I
101. to reposition the foot even if the change is not measurable on the shell What is the maximum width the shell can expand to Up to 6 mm with the push of the foot only What is the advantage compared to normal bootfitting Here it is the foot which changes the shell there is no more risk of misinterpretation the precision is perfect Also this process saves time 30 min to do everything amp the customer leaves with his her boots and an easier manipulation every KOTF can do it Should the custom soles be done before or after Mold the soles before The customer should then step in the warmed Custom Shell with the insoles Should other areas of the shell be changed before or after A modification of the metatarsus s area can affect the positioning of the foot First the Custom Shell 56 should be complete Then the areas of the toes ankles and navicular bone can be changed as usual though avoid pushing on the borders of the Custom Shell insert Can push in the Custom Shell area with my bootfitting machine Yes but it is not recommended Since the Custom Shell material has not been created to resist to a push that is superior the feet s push avoid the side areas of the insert Does the plastic retract the same as normal boots when cooled Yes but two times less than normal plastic approximately 25 after the boots have been taken out a shell pushed out 4mm could come back to 3 mm What
102. urer Failing to tap when necessary can result in top skin or sidewall delamination broken screws or damage to the ski core To use a Salomon tap and brace 1 Position the brace so that the tap goes straight into the drilled hole 2 Apply only enough pressure on the brace to start the tap The tap is a self cutting tool and you have only to turn the brace for the tap to cut its own way into the core 3 Make 3 1 2 turns 4 After tapping turn the ski over and hit the base several times with the palm of your hand to remove any shavings from the hole 18 Diameter Junior Ski Group 3 amp 4 Imm 95mm nm GLUE Glue must be used when inserting binding screws to lubricate the screw during insertion create a watertight seal Place a drop of glue on the surface of each hole Caution Salomon strongly recommends its own glue for Salomon skis Drill bit length MOUNTING Follow the mounting procedure and also refer to the section Special cases in mounting A Posidrive n 3 screwdriver not a Phillips must be used to mount Salomon bindings Consult the Salomon Spare Parts Catalog for reference on Salomon screws Caution if a power screwdriver is used adjust the clutch for the appropriate ski core cons truction 4 Nm maximum to avoid stripping the threads It is advisable to hand check each screw after mounting INSTALLATION 1 Position the toe piece over the dri
103. ventory Use the procedure below if the boot inventory includes several models and a representative boot can not be easily identified 1 Select five single boots with sole lengths as specified in Chart A for the binding type to be tested adult junior or child 2 Clean all five boots with a mild detergent and water 3 Adjust a rental binding to the release indicator setting specified in Chart A for the binding type 4 Fit the binding to the boots and determine the Release Torque in all three directions of release forward lean and both directions in twist three releases in each direction 5 Average the Release Torque for CW and CCW twist release 6 Reject and replace any boot with a CW to CCW difference of more than 6 Nm for adult boots or 4 Nm when testing child boot types T Rank the five twist results and select as the Reference Boot for twist the middle boot 8 Rank the five forward lean results and select as the Reference Boot for forward lean the middle boot PRESEASON BINDING INSPECTION The procedure that follows is an integral part of preseason maintenance It is also a good way to determine if mainte nance is adequate and which units have outlived their usefulness and must be removed from inventory 1 Clean areas of the bindings that contact the boot and perform all preseason binding maintenance 2 Visually or manually check a AFD condition b Brakes function Release indicator rea
104. wm 0 79 _ 80 MY PERFECT 17 A Impact test Penetration test Roll of test D Dynamic fastening device test E Covered areas measurement F Visibility measurement Salomon channelled all its experience for your protection and pleasure but dont lose your head Our helmets combine our recognized profession nalism and pure design to create protection for the senses Our comprehensive range meets the best safety standards and uses the unique Advanced Fit Technology design for your comfort and performance Be smart and protect your head in style Helmets don t offer absolute protection so ride within your limits and take care INSTRUCTIONS FOR USE AND MAINTENANCE IMPORTANT the helmet must always be fastened on the head chin strap buckled under the chin Check the adjustment and the condition of your helmet before each use Always take care of your helmet even when not using it Store it away from any heat source and sunlight since prolonged exposure to the sun weakens all plastic materials it is recommended to replace your helmet at least every 3 years Let it dry in a ventilated area For cleaning the outside surface of the skull cap use soap and water only Do not use any type of gasoline products solvents or any other chemical substances Do not modify the helmet in any way Do not va
105. xtremely rare that a new component would be out of calibration unless there is damage Troubleshooting Boot binding systems wear with time Mechanical inspection allows you to identify when the ski boot binding system is not working as it was originally intended Readjustment of the binding is not a sign of malfunction but can be a sign of normal wear gt Test for lateral travel failure Re check all binding to boot adjustments Re inspect the boot and the binding according to the Visual Inspection criteria If the boot is dirty clean the sole with a solution of soap and water If the binding is dirty clean it according to the procedures described in this chapter under Maintenance Re test the system for elastic travel and return Test for vertical elastic travel failure Clean the boot sole of any snow dirt or debris Check for excessive wear at the boot heel Repair or replace any non DIN boot Check that the boot enters the binding correctly Align the boot with toe and heel cups and re insert the boot Check the release setting It should not exceed the minimum or maximum visual indicator setting and should be set appropriately for the skier If the measured Mz and My values are located outside of the 15 inspection range consult the manufacturer s instructions for procedures concerning malfunctions If after this procedure the measured values are within the readjustment range of 30 the
106. y Operation All models except of drill bit 41 mm Tapping No Glue put the glue at Salomon glue the bottom of the hole epoxy Torque 4 Nm SELECTING AND USING THE JIG The main function of a jig is to insure that all holes for mounting the binding are drilled in the correct location See chart to select the proper jig 1 Check that you have everything you need the jig that corresponds to the binding the right skis the right boots 2 Open the locking lever 3 Open the jig by twisting both handles inward Place the jig in the right direction on the ski 4 Place the jig on the ski and make sure that the jig remains properly aligned to the ski during the entire drilling operation fig 1 If the ski has a mid sole mark line up the mid sole indicator on the jig with the mid sole mark on the ski fig 2 If the ski has a tip of the boot mark line up the tip of boot sole indicator on the jig with the tip of boot mark on the ski If the ski has no visible markings for jig location consult the ski manufacturer for proper mounting position 5 Once the jig is well positioned on the ski it is important to adjust the jig to the correct boot length to make sure the heel piece is in the proper position 6 Place the boot on the jig in the right direction T Make sure the heel guide fits snugly against the boot heel 8 Using the lever lock the jig around the boot so it holds it without squ

TECHNICAL MANUAL ALPINE - the salomon technician programme

Contents

Download Pdf Manuals

Related Search

Related Contents