Preface - Axis Communications
Contents
1. In DSC DSE and LU 1 modes the M PP value sets the page width in characters In LU 1 mode this sets default power on value In DSC D SE modes this setting cannot be overwritten If set to zero or a value larger than the physical page width the maximum page width becomes the default The maximum page width is determined by the paper size and parameters C01 C02 and C03 Value C13 Maximum Print Position MPP 0 999 Valid MPP values e 132 D efault MPP value 22 AXISAFP MIO Coax User s Manual C15 N ote C16 C17 N ote Section 2 Installation and Configuration Early Print Complete Response Timing C15 EPCRT Controls when the printer will acknowledge a Form Feed either an automatic FF or a valid FF code Valid for non I PD S modes only Value C15 Early Print Complete Response Timing 0 A FF will be acknowledged when the page has been transferred to the printer s page buffer This setting gives maximum throughput but data may be lost on a IR or if the printer loses power 1 In DSC DSE modes aFF will not be acknowledged until the print job is physically completed In LU 1 the printer will function as if this option was set to zero unless chaining techniques are used see PAI address X 0017 bits 1 amp 2 However if a FF automatic or control code is found in a Last or Only segment the FF will not be acknowledged until the print job is physically completed T hisoption isinverted compared to the IBM 382. 3 3440 bytes 4 3564 bytes C11 Extended Attribute Buffer EAB oe se se se se se se ae ee CII EAB EAB is used for character attributes APL printing etc D SC D SE modes only Value C11 Extended Attribute Buffer EAB 0 EAB enabled 1 EAB disabled AXIS AFP MIO Coax User s Manual 21 Section 2 Installation and Configuration C12 Characters per Inch CPI esse ee ee C12 CPI Selects how many characters to print per inch and thedefault font In LU 1 mode this sets default power on value In DSC DSE modes this setting cannot be overwritten Value C12 Characters per Inch CPI 0 10 pitch C ourier 13 pitch Gothic text when COR is active 1 12 pitch Prestige 15 pitch Gothic text when COR is active 2 15 pitch G othic text 20 pitch G othic text when COR is active 3 17 pitch C ourier 27 pitch Gothic text when COR is active C13 Maximum Page Length MPL ou se se se se se an se ee CL3 M PL In DSC DSE and LU 1 modes the M PL value sets the page length in lines In LU 1 mode this sets default power on value In DSC D SE modes this setting cannot be overwritten If set to zero or a value larger than the physical page length the maximum page length becomes the default The maximum page length is determined by the paper size and parameters C01 C02 and C03 Value C13 Maximum Page Length MPL 0 999 Valid MPL values 66 Default MPL value C14 Maximum Print Position M PP ie ee ee se ee C 14 M PP
3. 31 2 Txp TxD 3 _ 3 RxD RxD 2 3 RxD RxD 2 2 TxD SG 5 5 SG SG 5 7 SG DTR 4 6 DSR DTR 4 gt 6 DSR 7 RTS l 4 RTS 8 CTS 5 CTS AXIS AFP MIO Coax User s Manual 55 Appendix D RS 232C Interface 56 AXISAFP MIO Coax User s Manual Appendix E How to contact Axis Appendix E How to contact Axis If you need technical support please contact your dealer If they can t help you they will forward your request through the appropriate channels Internet and World Wide Web If you are connected to Internet havea look at the Axis WWW Home Page at http www axis se H ere you can find information about the company and our products You can also down load on line manuals tools such as the Acrobat R eader for different platforms and the latest versions of the software utilities You can also get files and information through anonymous ftp log in to ftp axis se and go to the pub axis directory The Axis offices Europe M iddle East South America Africa Ausralia If you want to contact an Axis office choose the one nearest to your region Axis Communications AB Schedevagen 16 S 223 70 Lund Sweden Phone 46 46 19 18 00 Fax 46 46 13 61 30 Email info axis se AXIS AFP MIO Coax User s Manual 57 Appendix E How to contact Axis 58 North amp Central America Japan H ong Kong Ada except Japan amp M iddleE ast Axis
4. Additional N ew Line at M PP H a C19ADDN L T his option is used in DSC D SE modes only Value C18 Automatic New Line at MPP 1 0 No automatic NL when a NL is executed at MPP 1 N ew print position is at the beginning of the next line 1 Anextra NL is inserted when a NL is executed at MPP 1 New print position is at the beginning of the line after the next line Form Feed Within the Print Buffer C20 FFPB T his option is used in DSC D SE modes only Value C20 Form Feed Within the Print Buffer 0 Next print position is next form line 1 position 2 1 Next print position is next form line 1 position 1 Form Feed at End of Print Buffer ii ese C21 FFEPB T his option is used in DSC D SE modes only when C16 0 Value C21 Form Feed at End of Print Buffer 0 No automatic NL at print order completion ol An automatc NL at print orser completion is inserted N Ull SUPPRESS ON nenns C22 NS T hisoption isused in DSC D SE modes only Value C22 Null Suppression 0 Suppress lines with only non printable characters 1 Do not suppress lines with only non printable characters AXIS AFP MIO Coax User s Manual C23 C24 C25 C26 C27 Section 2 Installation and Configuration Form f eed Command Position sesse sees is sees C23 FECP T his option is used in DSC D SE modes only Value C23 Form Feed Command Position 0 FF is only valid at the beginning of a line and at MPP 1 1 FF is valid anywhere Automatic Func
5. Coax User s Manual 33 Section 2 Installation and Configuration Baud Rat Badr dere uses EES ee RE PRES Ge EE ta BAUDRATE Sets the baud rate for the serial port Value 300 600 1200 2400 4800 9600 19200 Protocol Protocol ee ee ee RR Ge Re ee ee ee Re ee ee Ee Baud Rate 300 baud 600 baud 1200 baud 2400 baud 4800 baud 9600 baud 19200 baud ME PROTOCOL Selects the handshake protocol Value Robust Xon H W DTR Polarity DTR Polarity serere Protocol Robust handshake X on X off handshake Hardware handshake annn DTR POLARI Sets the DTR polarity for the srial port Value HIGH LOW Data Bits DataBitS ee ee ek ee Re ee ee ee Re ee ee Ee DTR Polarity DTR active high DTR active high bestee DATA BITS Sets the number of data bits word length for the serial port Value 7 8 34 Data Bits Use seven data bits Use eight data bits AXISAFP MIO Coax User s Manual Section 2 Installation and Configuration ie AA te RE OO PARITY Sets the parity for the serial port Value Parity N one No parity Even Even parity Odd Odd parity Mark Mark parity Space Space parity Stop Bits Stop BItS ES EE ES ee et ees STOP BITS Sets the number of stop bitsfor the serial port Value Stop Bits ol Use one stop bit 2 Use two stop bits AXIS AFP MIO Coax User s Manual 35 Section 2 Installation and Configuration 36 AXISAFP MIO Coax User s
6. XX XX indicates that the AXIS AFP MIO hasa fatal error T ry to power off the printer wait for at least 3 seconds and then power on the printer again If the error reappears please remember the error code and refer to Appendix E Customer Support AXIS AFP MIO Coax User s Manual 43 Section 3 Front Panel O peration Wa AXISAFP MIO Coax User s Manual Appendix A T echnical Specifications Appendix A Technical Specifications Hardware Compatible Printers Printer M emory Requirements 3270 Attachment Physical Attachment H os PC Sharing A RISC based printer controller including a 1 M byte PCM CIA Flash Card to be installed in the M odular I O accessory slot of the new genera tion of printers from H ewlett P ackard TheFLASH memory card contains micro code and the resident fonts HP Laserjet 4 4Si 4 4V and IIISi HP Paintjet XL300 HP Design et 600 and 650C HP Color LaserJet H P Desk et 1200C 1600 C A total of minimum 2 M bytes of memory is required in the H P printer 4 M bytes memory is recommended to get optimal performance e IBM 3174 Control U nit Configuration Support A rel 3 0 or later IBM 3274 Control U nit Configuration Support D rel 65 1 or later e 9370 WSA Control Unit or equivalent equipment Coax cable Dynamic sharing between an IBM host and astandard PC using RS 232C interface AXIS AFP MIO Coax User s Manual 45 Appendix A Technical Specifications Emulatio
7. Manual Section 3 Front Panel O peration Section 3 Front Panel Operation Front Panel Keys and Indicators T he installation of the AXIS AFP MIO interface adds new functions to the front panel of your HP printer T his chapter describes how to operate the front panel when the interface is installed in an HP Laser amp 4 printer T he front panel of the H P LaserJet 4 consists of a 16 character Plasma display eight function keys and three indicator lights The following explains how to use the frontpanel to customize the AXIS AFP MIO interface A schematic overview can be found in Appendix C Front Pand M enu OnLine T he On Line gt function key is used to take the printer off line or return it ed to the on line setting T he n Line gt light indicator lights when the printer is on lineT he printer will not print any pages when off line AXIS AFP MIO Coax User s Manual 37 Section 3 Front Panel O peration Changing the IPDS Coax Serial and Printer Options 38 Menu Reset Item Continue Item Continue Item Continue Important With the printer off line press the lt M enu gt key several times until MIO MENU or AUX IO MEN U is displayed Press the dtem gt key and CFG N O is displayed U sethe lt gt or lt gt function key to select between IPD S Coax Serial and Printer options Press the lt Enter gt key to select the desired option Press the dtem gt key to select the desired IPD
8. S Coax Serial or Printer option N ow you have the following possibilities to change the selected option T he lt gt key will get you the next valid value T he gt key will get you the previous valid value T he lt Enter gt key will store the displayed value An asterisk indicates that this value is now stored U se the dtem gt key to select the next option Use the following key to leave the configuration menu Press the lt O n Line gt key anytime you want to leave the configuration menu Changing the options will have no effect until the next Power on AXIS AFP MIO Coax User s Manual Section 3 Front Panel O peration Resetting to Default Option Values Mena With the printer off line press the M enu gt key several times until MIO MENU or AUX IO MENU is displayed Reset Item Press the dtem gt key and CFG N O is displayed Continue Press the lt gt function key until C FG CARD DFLT is displayed Press the lt Enter gt function key to restore the default option values Online Press the d n Line gt key to leave the configuration menu Important Changing the options will have no effect until the next Power on Printing a Printer Self Test Page Menu With the printer off line press the lt M enu gt key several times until TEST MENU is displayed Reset ia Press the dtem gt key and SELF TEST is displayed Continue Press the lt Enter gt function key to print the p
9. The display will only be updated every time you press the lt Enter gt key Display WAITING SER BLO CKS nnnnn REMO VE CARD INSERT CARD ERASIN G PROGRAMMING RESULT OK Display NO CARD MEM IN USE ERASE ERR PROGRAM ERR W RT PROTECT AXIS AFP MIO Coax User s Manual Action Start load from the PC by entering AFPMLO AD with the required parameters nnnnn indicates the number of 192 bytes blocks transmitted Remove the FLASH memory card Insert aFLASH memory card It is recommended not to use the original FLASH memory card in case of failing load of the new soft ware Erasing the FLASH memory card Programming the FLASH memory card FLASH memory card programmed Turn the printer OFF ON to activate the new software Error Indication No FLASH memory card in the slot The AXIS AFP MIO is using the RAM to prepare pages for printing Error erasing the FLASH memory card Error programming the FLASH memory card The FLASH memory card is write protected 41 Section 3 Front Panel O peration Copy the FLASH Memory Card 42 Menu Reset Item Continue On Line TheAXIS AFP MIO interface can be used to copy the FLASH memory card Thisis very useful in an organisation with morethan one AXIS AFP M10 printer to distribute software updates to all the printers To copy the FLASH memory card With the printer off line press the lt M enu gt key several times until MIO MENU or AUX IO MENU
10. eight towers of command sets each representing a major printer capability Five data towers T ext IM Image IO Image Graphics and Bar Code and three resource towers Page Segment O verlay and Loaded Font With IPDS it is possible to e use theall points addressable printing capability of the page printer to print text graphics images or bar codes at any point on the page e use images and vector graphics to print line drawings pie charts bar charts graphics logos signatures etc e combine dl kinds of data on the same page print in all rotations either on separate pages or on the same page e electronically store and later print forms and letterheads e electronically store and later print host fonts AXIS AFP MIO Coax User s Manual 9 Section 1 General Information IBM Printer TheAXIS AFP MIO solution is plug compatible with eather the IBM Emulation 4028 N S1 3912 16 3112 16 page printer or thelBM 3816 page printer IPDS only An IPDS option selects the BM mode to be emulated Refer to IPD S Optiong PC SharingFeature Whe using the AXIS AFP MIO interface your H P printer can automatically be shared between an IBM host and aPC ThePC has to beconnected to theR S 232C input port on the AXIS AFP MIO interface or to the standard Centronics paralld and or the serial input of the HP printer T he printer will switch between host and PC mode on a timeshare basis W hen the RS 232C port on the AXIS AFP M IO is active
11. for Default O ption Values see page 39 lt Enter gt to copy the Flash Card see page 42 lt Enter gt to load new Micro Code see page 40 51 Appendix C Front Panel Menu Printer O ptions FMARG FMARG BMARG BMARG EMARG EMARG ALTER THIRD PAPER PAPER PAPER R R PAPE PAPE OUT ERROR IPD S Options TRAY TORAS OCORA LEFT 000 TOP SONG LEFT 000 ORs OOO LEFT 000 PRIM CASS MAIN CASS ALT CASS NONE MAIN A4 ALT A4 OPT A4 ENV NONE MAN NONE DEF BEEP NO IPDS EMUL 3816 CP VERSION 0 a EXCEPTION 0 CNT UPDATE 0 Ly RESOURCE NORM DUPLEX PRT NO PRINT Coax O ptions COO RES 52 AREA 3816 000 Press lt gt lt gt to change value lt Enter gt to save lt ten gt for next Top Margin for Front see page 27 Left Margin for Front see page 27 Top Margin for Back see page 27 Left Margin for Back see page 27 Top Margin for Envelope see page 28 Left Margin for Envelope see page 28 Primary C assette see page 28 Alternate C assette see page 28 Third Cassette see page 29 MAIN Cassette Paper Size see page 29 ALT Cassette Paper Size see page 29 OPT Cassette Paper Size see page 30 ENV Cassette Paper Size see page 30 MAN Cassette Paper Size see page 31 Output Tray see page 31 Error Beep see page 32 Press lt gt lt gt to change value lt Enter gt to save lt ten gt for next Emulation see pag
12. is displayed Press the dtem gt key and CFG N O is displayed Press the lt gt function key until C FG FLASH CPY is displayed Press the lt Enter gt function key to start the FLASH memory card copy procedure Press the lt O n Line gt key anytime to terminate the Copy procedure AXISAFP MIO Coax User s Manual Section 3 Front Panel O peration T he following messages will appear in the display Important T he display will only be updated every time you press the lt Enter gt key Display CHECKING 7 READING CARD REMOVECARD INSERT COPY ERA SIN G ag PROGRAMMING RESULT OK Q Display NO CARD SAME CARD MEM IN USE b ERASE ERR i PROGRAM ERR WRT PROTECT Printer Status Messages Action Checking that a FLASH memory card is inserted Reading the FLASH memory card Remove the FLASH memory card Insert the FLASH memory card that you want to copy to Erasing the FLASH memory card Programming the FLASH memory card FLASH memory card programmed Error Indication No FLASH memory card in the slot The software on the inserted FLASH memory card is identical to the original The AXIS AFP MIO is using the RAM to prepare pages for printing Error erasing the FLASH memory card Error programming the FLASH memory card The FLASH memory card is write protected Refer to the User s manual of the specific H P printer for printer error or service messages A 80 SERVICE
13. 12 3816 printers On the 3812 3816 C15 0 means that the FF will not be acknowledged until the print job is physically completed Automatic Function at End of OILC JOD cece C16 AFEO T his option is used in DSC D SE modes only Value C16 Automatic Function at End of OILC Job 0 The setting of parameter C24 controls how the printer handles the end ofa print order 1 A FF is executed after the print buffer has completed a local copy job Timeout on N o Data LOSSIR se se CIZ ENAIR T his option controls how to report special conditions such as paper out toner low etc in all modes Value C17 Timeout on No Data Loss IR NO No Intervention Required IR is sent on No Data Loss conditions YES IR is sent to the host after some time if the condition continues Enabling this option will force reporting of Stacked Page C ounter after pages have been printed i e operation will proceed as if IPD S Stacked Page Counter was enabled see page 18 AXIS AFP MIO Coax User s Manual 23 Section 2 Installation and Configuration C18 C19 C20 C21 C22 24 Automatic N ew Line at M PP assesses C18 AUTON L T his option is used in DSC D SE modes only Value C18 Automatic New Line at MPP 1 0 No automatic NL when a CR is executed at MPP 1 New print position is at the beginning of the current line 1 An automatic N L is inserted when a CR is executed at MPP 1 N ew print position is at the beginning of the next line
14. 17 Courier bold 17 Courier 17ss APL 20 Gothic text 20 Gothic text 27 Sonoran serif 8pt Sonoran serif 10pt Sonoran serif bold 10pt Sonoran serif ItaliclOpt Sonoran serif 12pt Sonoran serif bold 16pt Sonoran serif bold 24pt b created by bolding algorithm s simulated by substitution 48 AXIS AFP MIO Coax User s Manual Appendix B IPDS Font Summary IBM 4028 Emulation Fonts Axis font IBM font ID CPI Point Size Equivalent IBM font OCR B 3 10 12 O CR B Courier 11 10 12 Courier Prestige Pica 12 10 12 Prestige Pica Courier Italic 18 10 12 Courier Italic OCR A 19 10 12 OCR A Courier Bold 46 10 12 Courier Bold APL 76 12 10 APL Courier 85 12 10 Courier Prestige Elite 86 12 10 Prestige Elite Courier Italic 92 12 10 Courier Italic Prestige Elite Bold 111 12 10 Prestige Elite Bold Prestige Elite Italic 112 12 10 Prestige Elite Italic Boldface 159 PS 12 Boldface Prestige 164 PS 12 Prestige Prestige 221 15 9 Prestige Courier 223 15 9 Courier Courier 254 17 1 8 5 Courier Prestige 256 17 1 8 5 Prestige Letter Gothic 281 20 75 LetterG othic Nimbus Roman 5687 Typo 6 Times Roman N imbus Roman 5687 Typo 8 Times Roman N imbus Roman 5687 Typo 10 Times Roman N imbus Roman 5687 Typo 12 Times Roman N imbus Roman Bold 5707 Typo 10 Times Roman Bold N imbus Roman Bold 5707 Typo 12 Times Roman Bold N imbus Roman Bold 5707 Typo 14 Times Roman Bold N imbus Roman Bold 5707 Typo 18 Times Roman Bold N imbus Roman Bol
15. 17 IPDS Exception Control 17 Stacked Page C ounter 18 Resource M emory Size 18 D uplex Enable 18 Print Area 18 Coax Options CFG C OAX OPT 19 col 19 AXIS AFP MIO Coax User s Manual V vi C02 19 C03 19 C04 20 C06 20 C08 21 C09 21 C10 21 C11 21 C12 22 C13 22 C14 22 C15 23 C16 23 C17 23 C18 24 C19 24 C20 24 C21 24 C22 24 C23 25 C24 25 C25 25 C26 25 C27 25 C28 26 C29 26 C30 26 Printer O ptions CFG PRT OPT 27 Top M argin for Front 27 Left M argin for Front 27 Top M argin for Back 27 Left M argin for Back 27 Top M argin for Envd ope 28 Left M argin for Envelope 28 Primary Cassette 28 Alternate C assette 28 Third C assdte 29 MAIN Cassette Paper Size 29 ALT Alternate Cassette Paper Size 29 OPT Optional Cassette Paper Size 30 AXIS AFP MIO Coax User s Manual ENV Envelope Cassette Paper Size MAN M anual Feed Paper Size O utput T ray Error Beep Serial O ptions CFG SER OPT Enable Serial Timeout Baud Rate P rotocol DTR Polarity D ata Bits Parity Stop Bits 3 Front Panel Operation Front Panel Keys and Indicators Changing the IPDS Coax Serial and Printer O ptions Resetting to D efault O ption V alues Printing aPrinter Self T est Page Load N ew Software via the RS 232C Interface Copy the FLASH M emory Card Printer Status M essages A Technical Specifications H ardware Compatible Printers Printer M emory Requirements 3270 Attachment Physical Attachment Hos PC Sharing Emulation R
16. 5 United Kingdom 36 500 Reserved 15 286 Alt Austria G ermany 37 1026 Turkish 16 287 Alt Denmark N orway 38 500 Reserved 17 288 Alternate Finland Sweden 39 905 Turkish 18 289 Alternate Spain 40 870 Latin2 19 290 Japan K atakana 41t 423 Greek 20 293 APL 42 875 Greek 21 9 France t Special AFP MIO LAN fonts needed C06 HIMES SC nd ie ED ie ttt C06 LS Controls the line spacing for non l PD S coax modes In LU 1 mode the line spacing can be changed by commands from the host Value C06 Line Spacing 0 Single line spacing 1 Double line spacing 20 AXISAFP MIO Coax User s Manual Section 2 Installation and Configuration COB Monocase D ual Case ee ese Ee GEREED RES GE bed eds C08 MD U se this option to force upper case printing D SC D SE modes only Value C08 Monocase Dual Case 0 Normal dual case printing 1 Always use upper case C09 Lines per Inch Ply n Ee be De EG tana C09 LPI Selects how many lines to print per inch In LU 1 mode this sets default power on value In DSC D SE modes this setting cannot be overwritten Value C09 Lines per Inch LPI 0 6 LPI 8 57 LPI when COR is active 1 8 LPI 11 43 LPI when COR is active C10 Screen SizeLocal COPY ee cacao C10 SSLC Selects screen size for local copy operation D SC D SE modes only For some controllers this value must be correct for the communication to start Value C10 Screen Size Local Copy 0 960 bytes ol 1920 bytes 2 2560 bytes
17. 9 Duplex 18 E Error Beep 32 F FLASH M emory Card 42 Font Summary IBM 3812 47 IBM 4028 49 Front Pand 37 51 I IBM 3270 environment 13 Internet 57 IPDS 9 Options 17 M M argins 27 M edia Sizes 11 M emory Requirements 10 Interface 10 Printer 10 SIMM modules 11 AXIS AFP MIO Coax User s Manual Index P PC Sharing Feature 10 Printer Emulation 10 Printer O ptions 27 38 R RS 232C Interface 55 S Serial O ptions 33 80 SERVICE XXXX 43 Software 40 T T echnical Specifications 45 T et Page Printer 39 U Utility Program 13 W World Wide W eb 57 61 Index 62 AXISAFP MIO Coax User s Manual
18. Communications Inc 4 Constitution W ay Woburn MA 01801 1030 USA Phone 1 800 444 AXIS 617 938 1188 Fax 617 938 6161 Email info axisinc com Axis Communications KK 8th Center Plaza 5F 1 10 16 N ihombashi H oridome cho Chuo ku Tokyo 103 J apan Phone 8 13 3663 8801 Fax 8 13 3663 8802 Email info axiscom co jp Axis Communications LT D Room 602 Asian H ous 1 H ennessy Road Wanchai Hong Kong Phone 852 2836 0813 Fax 852 2573 5935 Email info axis com hk AXISAFP MIO Coax User s Manual Appendix F Related Publications Appendix F Related Publications For additional information please refer to the following publications Title IBM Intelligent Printer Data Stream Reference IBM Page Printer 3812 Installation and Programming Instructions for 3270 Information Display Systems Attachment IBM Pageprinter 3812 IPDS Handbook IBM 3812 and 3816 Page Printers Font Reference 3270 Programming Guide and Reference Manual for the IBM Laser Printer 4028 Model NS1 IBM LaserPrinter 4028 IPDS Handbook HP LaserJet 4 User s Manual HP Paint Jet XL300 Color Printer User s Guide AXIS AFP MIO Coax User s Manual Part no 544 3417 544 3101 544 3102 GA34 2111 544 4262 544 4260 59 Appendix F Related Publications 60 AXISAFP MIO Coax User s Manual Index A Anonymous FT P 57 Axis offices 57 C Cassettes 28 Coax Options 19 Code Page Version 20 D D efault O ption Values 3
19. IN Cassette Main Cassette Paper Size ie se se ee PAPER MAIN Paper Size ps Selects paper size for the main cassete Value MAIN Cassette Paper Size Ad Paper size for top cassette is A4 LET Paper size for top cassette is Letter LEG Paper size for top cassette is Legal EX EC Paper size for top cassette is Executive A3 Paper size for top cassette is A3 Bsiz Paper size for top cassette is AN SI B size ALT Alternate Alternate C assdte Paper Size ie se PAPER ALT Cassette Paper Size ad Selects paper size for the alternate cassette Value ALT Cassette Paper Size Ad Paper size for alternate cassette is A4 LET Paper size for alternate cassette is Letter LEG Paper size for alternate cassette is Legal EXEC Paper size for alternate cassette is Executive A3 Paper size for alternate cassette is A3 Bsiz Paper size for alternate cassette is ANSI B size AXIS AFP MIO Coax User s Manual 29 Section 2 Installation and Configuration OPT Optional Optional Cassette Paper Size ie se ee ae ee PAPER OPT Cassette Paper Size Selects paper size for the optional cassette Value OPT Cassette Paper Size A4 Paper size for optional cassette is A4 LET Paper size for optional cassette is Letter LEG Paper size for optional cassette is Legal EX EC Paper size for optional cassette is Executive A3 Paper size for optional cassette is A3 Bsiz Paper size for optional cassette is AN SI B size ENV Envelope Envelope Cassette Pap
20. PDS emulation Value Duplex Enable YES Reply to host system indicates support for duplex printing NO Duplex not supported Print Area erne PRINT AREA T his option controls what Printable Area is reported in the Ob Printer Characteristics reply in the 4028 emulation Value Print Area 3816 Printable Area and the paper size is the same 4028 Printable Area is smaller than the paper size PRTP Supports 4028 Print Page option This option causes the upper left corner 0 0 of the Logical page to be forced inside the 4028 Printable area T his option has no effect in the 3812 16 emulation AXISAFP MIO Coax User s Manual Section 2 Installation and Configuration Coax Options CFG COAX OPT N ote col C02 C03 T he valid values for each option are listed and the default settings are indicated by a bullet Changes to any of the options described will only take effect at the next printer Power on Primary Cassette Print Orientation secsec C01 PCPO Controls how to print when using the primary cassette in all non IPD S coax modes Primary cassette can be ather the top or the bottom drawer See page 28 for further details Value C01 Primary Cassette Print Orientation 0 Print using landscape orientation and a reduction of the output to around 70 1 Portrait mode no reduction 2 Landscape mode no reduction Alternate C assette Print O ption ee soe se se C 02 ACPO Controls how to print when usi
21. Preface About Axis N etwork CD ROM Servers Network Print Servers IBM Mainframe and S 3x AS 400 Printer Interfaces T hank you for purchasing theAXIS AFP MIO Printer Interface O ur goal in developing this product is to enable you to connect your H P printer to your IBM IPDS environment allowing you to take full advantage of both thelPDS functions and your H P printer capabilities Axis Communications founded in 1984 is one of the world s fastest growing companiesin the printer interface and network print server market T he head quarters are located in Lund Sweden with subsidiaries in Boston Tokyo and H ong Kong Axis Communications has a distributor network operating in more than 60 countries world wide marketing three product lines CD ROM servesprovidea flexible and cost efficient solution for sharing CD ROM s acrossthenetwork They areavdilable in Ethernet AXIS 850 851 and T oken Ring AXIS 950 951 versions with or without built in drive option T hese intelligent Ethernet and Token Ring print servers support a wide rangeof LAN protocols TheAXIS N PS 530 532 550 and AXIS 150 are Ethernet print servers and the AXIS NPS 630 632 and 650 are Token Ring print servers T heseproductsincludea wide range of plug in interfaces and freestanding box products such as the Cobra and the AFP IPD S to PostScript converter AXIS AFP MIO Coax User s Manual Revision 1 0 Part No 14361 Dated October 1995 Copyr
22. S Font Summary Equivalent IBM font OCR B O rator 10 Courier 10 Prestige 10 Artisan 10 Courier Italic 10 OCR A Pica 10 Matrix Gothic 10 Math symbol 10 O rator bold 10 Gothic text bold 10 Gothic text 10 Roman text 10 Serif text 10 Serif text Italic 10 Katakana gothic 10 APL 10 Courier bold 10 Prestige bold 10 Gothic text 12 Gothic text Italic 12 Gothic text bold 12 Serif text 12 Serif text Italic 12 Serif text bold 12 Math symbol 12 Script 12 Courier 12 Prestige 12 Letter gothic 12 Light Italic 12 47 Appendix B IPD S Font Summary 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 IBM font ID 107 108 110 111 112 155 158 159 160 162 163 173 175 176 177 204 221 222 223 225 229 230 244 245 252 253 254 280 281 290 751 4407 54 1051 4407 66 1053 4427 66 1056 4535 66 1351 4407 78 1653 4427 108 2103 4427 162 subs bold ID s 85 b 85 b 87 b 86 s175 b 175 b 160 s159 s155 s 230 s 230 s 230 s 86 s 230 b 244 b 252 Equivalent IBM font 12 Pitch Courier bold 12 Letter gothic bold 12 Prestige bold 12 Prestige Italic 12 Boldface Italic Modern Boldface Essay Essay Italic Essay bold Essay light Document Boldface Boldface Italic Gothic text 13 Prestige 15 Gothic 15 Courier 15 Math symbol 15 Serif 15 Gothic text 15 Courier 5 Courier bold 5 Courier
23. ce Installation Important 1 2 Caution 3 4 5 6 7 8 9 T ry to take antistatic precautions If a wristwrap is not available then touch something grounded aradiator or aPC cabinet before handling the PCB board Power off the printer and unplug the power cord Failure to power off the printer before installation may permanently damage parts of the AXIS AFP MIO product or printer LocatetheM IO interface slot Remove the plate covering the slot or the current interface in the slot Install the AXIS AFP MIO interface in the empty slot Secure the board using the screws Insert the FLASH memory card in the slot of the AXIS AFP MIO interface Connect the communication cables Coax cable from the 3x74 con troller and the power cord Power on the printer T hegreen indicator on the back panel will be lit if the connection with the host was succesful Your printer isnow ready for AFP IPD S printing Note Cables are not included in the AXIS AFP MIO package they have to be ordered separately 14 AXISAFP MIO Coax User s Manual Section 2 Installation and Configuration Configuring the AFP Printer N ote Coax O ptions IPD S Options To customize the AFP printer to your applications the AXIS AFP MIO has fivesets of options C oax options PD S options Printer options Serial options and Dump options Changes to any of the options described will only take effect at the next print
24. d 5707 Typo 24 Times Roman Bold N imbus Roman Italic 5815 Typo 10 Times Roman Italic N imbus Roman Italic 5815 Typo 12 Times Roman Italic N imbus Roman Bold Italic 5835 Typo 10 Times Roman Bold Ital O CR B 3 10 12 OCR B PS Proportional Spaced Typeface Typo Typographical T ypeface Times Roman is a registered trademark of Linotype AG and or its subsidiaries N imbus Roman is a functional equivalent of Times Roman AXIS AFP MIO Coax User s Manual 49 Appendix B IPDS Font Summary 50 AXISAFP MIO Coax User s Manual Appendix C Front Panel Menu Appendix C Front Panel Menu All AXIS AFP MIO options are found under the MIO MENU or AUX IO MENU With the printer off line press the lt M enu gt key several times until MIO MENU or AUX IO MENU is displayed AUX 10 Options Whe AUX IO MENU OR MIO MENU isdisplayed press the dtem gt key to get to the top leve of the AXIS HP M IO options CFG NO CG SPR Or Cite POS CHEE COAXKRO CGE SH O CEG CAR Dap Cie SILAS In Ena MUS AXIS AFP MIO Coax User s Manual PR ET EEL SEE LD lt gt lt gt lt gt lt gt lt gt lt gt lt gt lt gt or next or next or next or next or next or next or next or next lt item gt for MIO MENU or AUX IO MENU lt ltem gt for Printer O ptions lt Enter gt for IPDS O ptions lt Enter gt for Coax O ptions lt Enter gt for Serial O ptions lt Enter gt
25. e 17 Codepage Version see page 17 IPDS Exception C ontrol see page 17 Stacked Page Counter see page 18 Resource Memory Size see page 18 Duplex Enable see page 18 Print Area see page 18 Press lt gt lt gt to change value lt Enter gt to save dtem gt for next Switches c00 c30 see page 15 page 26 AXIS AFP MIO Coax User s Manual Appendix C Front Panel Menu Serial Options Press lt gt lt gt to change value lt Enter gt to save lt ten gt for next SER ENABLE NO S TIMEOUT 30s BAUDRATE 9600 PROTOCOL ROBU DTR POLARI HIGH DATA BITS 8 BART TY NONE STOP BITS 1 AXIS AFP MIO Coax User s Manual Enable Serial see page 33 Timeout see page 33 Baud Rate see page 34 Protocol see page 34 DTR Polarity see page 34 Data Bits see page 34 Parity see page 35 Stop Bits see page 35 53 Appendix C Front Panel Menu 54 AXIS AFP MIO Coax User s Manual Appendix D RS 232C Interface Appendix D RS 232C Interface TheAXIS AFP MIO serial RS 232C interface has the following pin configuration Pin no Description Direction 2 Received data RxD In 3 Transmitted data TxD Out 4 Data Terminal Ready DTR Out 5 Signal Ground SG 6 Data Set Ready DSR In not used 7 Request To Send RTS O ut pulled high AFP MIO PC COM port AFP MIO PC COM port 9 pin D sub 25 pin D sub 9 pin D sub 9 pin D sub FG 1 1 FG TxD
26. eout 15s 15 seconds 20s 20 seconds 30s 30 seconds 45s 45 seconds 60s 60 seconds 90s 90 seconds 2min 2 minutes 3min 3 minutes 5min 5 minutes C29 Horizontal Output ReducHON eee C29 HOR T his option reduces horizontal movements for non IPD S printing All movenentsin the horizontal direction are reduced by the percentage specified horizontal always means along the short side of the page regardless of print orientation Value C29 Horizontal Output Reduction 0 No reduction 1 1 reduction 2 2 reduction 3 3 reduction 4 4 reduction 5 5 reduction C30 SCS Page Format dada ER Ge ese de ee es ee ies ese 30 SCSPF T his option controls the page format in non IPD S modes Value C30 SCS Page Format NORM The logical page is equal to the printable area on the emulated printer ALL The logical page is equal to the paper size COMP Line spacing is reduced so that lines close to the paper edges can be printed without clipping Note For the 3812 3816 emulation the NORM and ALL settings are identical 26 AXIS AFP MIO Coax User s Manual Section 2 Installation and Configuration Printer Options CFG PRT OPT N ote Top Margin for Front Left Margin for Front Top Margin for Back Left Margin for Back T he valid values for each option are listed and the default settings are indicated by a bullet Changes to any of the options described will only take effect at the next pri
27. er Power on T he options are split into two groups Group A Printer and Serial options includesthe printer dependent options T hese options are rdated to the specific printer and the connecting environment This group of options can be changed from the front panel only Refer to Changing the IPDS Coax Serial and Printer Serial O ptions Group B C oax and IPDS options is used to modify the function of the basic emulation T hese optionsarerelated to the host system environment T his group of options can be changed from the front pand or loaded from the AXIS AFP MIO FLASH memory card Refer to Changing the IPD S Coax Serial and Printer Options or Resdting to D dault Option Values T he Coax options correspond to the IBM 3812 c parameters and relate mainly to the SCS D SC functionality of the AXIS AFP MIO T helPDS options change the way IPD S operates T hese options are not available on the IBM 4028 AS1 or thelBM 3816 printer T he following IPD S options are available for configuration Emulation Stacked Page C ounter Code Page Version Resource Memory Size IPDS Exception Control Duplex Enable Print Area AXIS AFP MIO Coax User s Manual 15 Section 2 Installation and Configuration 16 Printer options The Printer options are used to change printer rdated items in the configuration An example of a printer related item is margins T he following Printer options are available for configuration Top Margin for F
28. er SIZE ucts PAPER ENV Cassette Paper Size per Selects paper size for the envd ope cassette Value ENV Cassette Paper Size NONE Envelope feeder not installed MON Paper size for envelope feeder is Monarch COM Paper size for envelope feeder is CO M 10 DL Paper size for envelope feeder is DL C5 Paper size for envelope feeder is C5 30 AXISAFP MIO Coax User s Manual Section 2 Installation and Configuration MAN Manual Manual Feed Paper Size emmer PAPER MAN Feed Paper Size Value NONE A4 LET LEG EX EC A3 Bsiz MON COM DL C5 cA4 cLET cLEG cEXE cA3 cBsz Selects paper size for the manual feed MAN Cassette Paper Size Manual paper feed not used Paper size for manual paper is A4 Paper size for manual paper is Letter Paper size for manual paper is Legal Paper size for manual paper is Executive Paper size for manual paper is A3 Paper size for manual paper is AN SI B size Paper size for manual paper is Monarch Paper size for manual paper is COM 10 Paper size for manual paper is DL Paper size for manual paper is C5 Paper size A4 with auto continuation Paper size Letter with auto continuation Paper size Legal with auto continuation Paper size Executive with auto continuation Paper size A3 with auto continuation Paper size AN SI B size with auto continuation Note Auto continue means that the H P Laser et 4 printer will NOT stop and wait for the On Line key to be pressed when usin
29. esource M emory Size Configuration Examples of IBM H os Software Supporting IPDS Product Certifications Environment B IPDS Font Summary AXIS AFP MIO Coax User s Manual vii viii IBM 3812 Emulation Fonts IBM 4028 Emulation Fonts Front Panel Menu AUX IO Options Printer Options IPDS Options Coax Options Serial Options RS 232C Interface How to contact Axis Internet and W orld W ide W eb T he Axis offices Europe M iddle Eag South America Africa Australia North amp Central America Japan H ong Kong Asia except Japan amp M iddle East Related Publications Index AXISAFP MIO Coax User s Manual Section 1 General Information Section 1 General Information Introduction TheAXIS AFP MIO provides truelBM AFP IPDS capability on your HP printer without the loss of the PC connectivity It consists of a high speed RISC based printer controller and a 1 M Byte FLASH memory card containing software and the resident fonts T he interface should be installed in the M odular I O accessory slot of the HP printer T his unique solution gives you high speed AFP IPDS printing independent of the complexity of the printjob provided that the communication lines are fast enough IPDS Thelntelligent Printer D ata Stream IPDS is the host to printer data stream for Advanced Function Printing AFP subsystems It is part of IBM s System Application Architecture SAA T helPD S architecture is functionally divided into
30. ft M argin for Front for a description Primary Cassette ste se doe a PRIM CASS Selects paper source for the primary cassette Value Primary Cassette MAIN The main paper source lt ESC gt amp I1H ALT The dternate cassette source lt ESC gt amp l4H OPT The optional large source lt ESC gt amp I5H ENV The envelope feeder will be used as primary cassette MAN The manual feed will be used as primary cassette Alternate Coss Ca es catalan et EG ALTER CASS Selects paper source for the alternate cassette Value Alternate Cassette ALT The dternate cassette source lt ESC gt amp l4H MAIN The main paper source lt ESC gt amp I1H OPT The optional large source lt ESC gt amp I5H ENV The envelope feeder will be used as primary cassette MAN The manual feed will be used as primary cassette On the H P Laser et 4 the MP tray will be the bottom cassette if the optional lower cassette is not installed AXISAFP MIO Coax User s Manual Section 2 Installation and Configuration Third Cassette Third Cassette ee ie ee ee ee ee ee ee ee ee ee ee ee ee ee THIRD CASS Selects paper source for the third cassette Value Third Cassette NONE No third cassette MAIN The main paper source lt ESC gt amp I1H ALT The dternate cassette source lt ESC gt amp I4H OPT The optional large source lt ESC gt amp I5H ENV The envelope feeder will be used as primary cassette MAN The manual feed will be used as primary cassette MA
31. ften practical to suppress exception reporting on undefined characters and position errors printing outside valid printable area Value IPDS Exception Control 0 No suppression of exceptions 1 Exception reporting for position errors is suppressed 2 Exception reporting when an undefined character is found is suppressed 3 Both position errors and undefined character exceptions are suppressed T his option overrides the EH C control in the IPDS data stream AXIS AFP MIO Coax User s Manual 17 Section 2 Installation and Configuration Stacked Page Counter Resource M emory Size D uplex Enable Print Area N ote 18 Stacked Page COUN siese ee Re ee ee CNT UPDATE U sed to select maximum printing speed early update or maximum security concerning recovery if the printer is powered off while printing a job Value Stacked Page Counter 0 Early updating of page counters in the IPDS replies 1 Late updating Resource M emory SIZE ee nance Ee sk Ge EE RESOURCE Determines how much memory is used for resources Value Resource Memory Size NORM Normal split between resource and output buffer memory LESS Allocate less memory to resources This frees more memory for output buffers MORE Allocate more memory to resources at the expense of output buffer memory Duplex Enable ss sek ek oe Ve GR Ge ea Ee ee ds ie eg DUPLEX PRT When the printer has the duplex option installed this option is used to enable duplex in the
32. g manual feed Recommended settings for the H P4 printer are MP TRAY CASS LOCKMP MANUALFEED OFF Output Tray Output T ray 2 Eie ER ee ee ee ge OUT TRAY O utput tray options Value Output Tray DEF Use output tray selected from the front panel TOP Face down output SIDE Face up output AXIS AFP MIO Coax User s Manual 31 Section 2 Installation and Configuration Error Beep Error Beep ske seks are ee ee tees ERROR BEEP Acoustic warning when error Intervention Required Value Error Beep NO No acoustic alarm when printer error ONE 6 beeps one time CONT 6 beeps continuosly 32 AXISAFP MIO Coax User s Manual Section 2 Installation and Configuration Serial Options CFG SER OPT T he valid values for each option are listed and the default settings are indicated by a bullet Note Changes to any of the options described will only take effect at the next printer Power on Enable Serial Enable Serial nnn SER ENABLE En les or disables the serial port Value Enable Serial MES RS 232C RS 422 input enabled NO RS 232C RS 422 input disabled Timeout TimEOU nel TIMEOUT T his option specifies for how long the AXIS AFP MIO interface will be waiting for more data on the serial port beforeit will change printer access Value Timeout 15s 15 seconds 20s 20 seconds 30s 30 seconds 45s 45 seconds 60s 60 seconds 90s 90 seconds 2min 2 minutes 3min 3 minutes 5min 5 minutes AXIS AFP MIO
33. ight Axis Communications AB 1995 AXIS AFP MIO Coax User s Manual i About this manual G eneral Informati on Installation and Configuration Front Pand O perati on T hismanual will guide you through a simple step by step installation and setup procedure It is divided into three sections About the AXIS AFP MIO Printer Interface how it works where to use it and its main features H ow to install your AXIS AFP MIO into your printer and how to configure it in your AFP printing environment H ow to operate the H P printer s front pand when the AXIS AFP MIO is installed T he manual applies to theAXISAFP MIO with firmware release 1 00 and subsequent releases until otherwise notified Every care has been taken in the preparation of this manual if you detect any inaccuracies or omissions pleaseinform us at the address on the back cover Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice AXISAFP MIO Coax User s Manual Emission notices USA This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause interference to radio communica tions It has been tested and found to comply with the limits for a Class A computing device pur suant to Subpart B of Part 15 of FCC rules which are designed t
34. n Resource M emory Size Configuration Examples of IBM H ost Software Supporting IPD S Product Certifications Environment 46 Either IBM 3816 compatible including the standard 35 resident fonts functional equivalent to thelBM fonts or 4028 N S1 compatible 3912 16 3112 16 including the standard 32 resident fonts functional equivalent to thelBM fonts All PD S towers supported D uplex is availa blein both emulations M orethan 1 M byte of I PD S resource memory dependent on the configu ration i e paper size U pgradable with standard SIM M memory module 1 2 4 or 8 M bytes Configured from the printer front panel PSF M VS Rdease 2 1 PSF VM Release 1 1 D W 370 Rd se2 GDDM Release 1 modification 1 CE EN 50082 1 EN 55022 1987 FCC ClassA Safety All safety regulations according to HP printer specifications Temperature 5 40 C 40 105 F H umidity 10 90 RGH non condensing Technical specification information is subject to change without notice AXISAFP MIO Coax User s Manual Appendix B IPDS Font Summary IBM 3812 Emulation Fonts 10 11 12 13 14 wn g IBM font ID 3 5 11 12 13 18 19 20 26 30 38 39 40 41 42 43 44 45 46 60 66 68 69 70 71 72 80 84 85 86 87 91 AXIS AFP MIO Coax User s Manual subs bold ID sll sll s 12 s 40 sll DES b 40 s40 s40 s 68 b11 b12 b 66 s 66 s 68 s 69 s 86 s 112 Appendix B IPD
35. ng the alternate cassette in all non IPDS coax modes Alternate cassette can be either the top or the bottom drawer See page 28 for further details Value C02 Alternate Cassette Print O ption 0 Print using landscape orientation and a reduction of the output to around 70 1 Portrait mode no reduction 2 Landscape mode no reduction Automatic Print O rientaion neni kele ee es ee es EOSAPO When automatic print orientation isenabled the printer checksthe paper size If the print data doesn t fit the default page size the printout is rotated T his function is used in all non I PD S coax modes Value C03 Automatic Print Orientation 0 APO enabled 1 APO disabled AXIS AFP MIO Coax User s Manual 19 Section 2 Installation and Configuration C04 Country Coders scien EE ait C04 CCSSP Use this option to select the default code page in IPDS mode Value CP Country Value CP Country 0 500 International Set 5 22 500 Reserved ol 37 USA C anada English 23 361 International Typographic 2 500 Reserved 24 437 Personal C omputer 3 500 Reserved 25 037 Alternate Portugal 4 260 Canadian French 26 871 Iceland 5 273 Austria G er many 27 892 OCR A 6 274 Belgium 28 893 OCR B 7 275 Brazil 29t 500 Arabic 8 277 Denmark N orway 30 500 Reserved 9 278 Finland Sweden 31 037 C anadian Bilingual 10 280 Italy 32 500 Swiss Bilingual 11 281 Japan English 33 284 Spanish 12 282 Portugal 34 500 Reserved 13 284 Spanish Speaking 35 500 Reserved 14 28
36. nter Power on Top M argin for Front EG ER Ee Re ee FM ARG TOP U sed for simplex pages and duplex front pages Top M argin can be used to adjust the top margin if the normal setting does not fit the printer or if a special requirement is needed The top margin is located at the leading edge of the paper Value Top Margin for Front 99 155 Valid values 0 Default Top Margin for Front Left M argin for FFONE ese see ve se ae se se se FM ARG LEFT U sed for simplex pages and duplex front pages Left M argin can be used to adjust the left margin if the normal setting does not fit the printer or if a special requirement is needed The left margin is located at the edge of the paper to the left of the leading edge Value Left Margin for Front 99 155 Valid values 0 Default Left Margin for Front Top M argin for Back ike Se EE ee Ge NE GR GE Ee Ede ee BM ARG TOP U sed for duplex back pages Refer to Top M argin for Front for a description Left M argin for Back ie sedes ve ke BM ARG LEFT U sed for duplex back pages Refer to Left M argin for Front for a description AXIS AFP MIO Coax User s Manual 27 Section 2 Installation and Configuration Top Margin for Envelope Left Margin for Envdope Primary Cassette Alternate C assette 28 N ote T op Margin for Envelope ceteris LEM ARG TOP Refer to Top M argin for Front for a description Left M argin for Envelope LEM ARG LEFT Refer to Le
37. o provide reasonable protection against such interference when operated in a commercial environment O per ation of this equip ment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the inter fer ence Shielded cables should be used with this unit to ensure compliance with the Class A limits E urope This digital equipment fulfils the requirements for radiated emission according to limit B of EN 55022 1987 and the requirements for immunity according to EN 50082 1 1992 residential commercial and light industry Compliance is not valid for unshielded network and printer cables Trademark acknowledgements Hewlett Packard and IBM are registered trademarks of the respective holders AXIS AFP MIO Coax User s Manual iii AXISAFP MIO Coax User s Manual Table of contents Preface i About Axis i About this manual ii Emission notices iii T rademark acknowledgements iii Table of contents v 1 General Information 9 Introduction 9 IPDS 9 IBM Printe Emulation 10 PC Sharing Feature 10 Printe M emory Requirements 10 Interface M emory Requirements 10 M adia Sizes 11 Fonts 11 2 Installation and Configuration 13 Contents of This D divery 13 Installation 14 Configuring the AFP Printer 15 Coax Options 15 IPDS Options 15 Printer options 16 Serial options 16 IPDS Options CFGSPDS OPT 17 Emulation 17 C odepage Version
38. rinter self test page AXIS AFP MIO Coax User s Manual 39 Section 3 Front Panel O peration Load New Software via the RS 232C Interface 40 R10 xxxx BIN AFPMLOAD EXE Menu Reset Item Continue On Line Important T he software of AXIS AFP MIO interface can either be updated by replacing the original FLASH memory card with a new preloaded card or by loading the new software from a standard DOS PC using serial RS 232C communication The AXIS AFP MIO interface then erases and reprograms the original FLASH memory card T he software is distributed on a floppy disk containing two files T he binary compressed software file xxxx indicates the version Load utility program Please use the following command to get information on how to usethe program A gt AFPMLOAD H Refer to Appendix D RS 232C Interface for pin assignment of the serial connector To load the new software to the AXIS AFP MIO interface With the printer off line press the lt M enu gt key several times until MIO MENU or AUX IO MENU is displayed Press the dtem gt key and CFG N O is displayed Press the lt gt function key until C FG FLASH LD is displayed Press the lt Enter gt function key to start the load procedure Press the lt O n Line gt key anytime to terminate the load procedure T he following messages will appear in the display AXIS AFP MIO Coax User s Manual Section 3 Front Panel O peration
39. ront Left Margin for Front Top Margin for Back duplex only Left Margin for Back duplex only Top Margin for Envelope Left Margin for Envelope Primary Cassette Alternate Cassette Third Cassette MAIN Cassette Paper Size ALT Alternate Cassette Paper Size OPT Optional Paper Size ENV Envelope Cassette Paper Size MAN Manual Feed Paper Size Output Tray Error Beep Serial options T he Serial options are used to set up the RS 232C port of the AXIS AFP MIO interface T he following Serial options are available for configuration Enable Serial Timeout Baud Rate Protocol DTR Polarity Data Bits Parity Stop Bits AXISAFP MIO Coax User s Manual Section 2 Installation and Configuration IPDS Options CFG IPDS OPT N ote Emulation C odepage Verdon IPD S Exception Control T he valid values for each option are listed and the default settings are indicated by a bullet Changes to any of the options described will only take effect at the next printer Power on EMU lQUO Wasnt aiid ee Gee ee ohne ee ee PD SEM UL T his option selectsthelBM printer to be emulated Value Emulation 3816 IBM 3816 4028 IBM 4028 N S1 3916 IBM 3912 16 IBM 3112 16 Codepage Verson N RS GE ee CP VERSION T his option selects between the old and the new version of some of the codepages Value Codepage Version 0 Use version 1 New 1 Use version 0 IPD S Exception Control ss ee N Ee ide EXCEPTION It is o
40. ry SIM M modules at your local H P dealer Media Sizes Whe using your H P printer as an AFP printer the following paper sizes are supported for the paper cassettes A4 210 x 297 mm Letter 8 5 x 11 inches Legal 8 5 x 14 inches Executive 7 25 x 10 5 inches A3 297 x 420 mm ANSI B size 11 x 17 inches T heH P printers have physical limitations i e the actual printable area is approx 4 mm inside the edges of the paper Fonts TheFLASH memory card contansa total of 67 resident fonts 32 IBM 4028 fonts and 35 IBM 3816 fonts Thefonts are functionally equivalent to the standard IBM 4028 N S1 and thelBM 3816 fonts Refer to Appendix B Reident Fonts for a full listing of the resident fonts AXIS AFP MIO Coax User s Manual 11 Section 1 General Information 12 AXISAFP MIO Coax User s Manual Section 2 Installation and Configuration Section 2 Installation and Configuration Contents of This Delivery TheAXIS AFP MIO interface package consists of these parts 1 x AXIS AFP MIO Coax interface main board Part no 0055 1 1 x AXIS AFP MIO Coax U ser s M anual Part no 14361 1x 1M byte PCM CIA Flash Card Part no 14357 Optional 1x 3 5 floppy disk Part no 14356 T he disk contains a PC based software download program Optional 1x PC Host D ownload Serial link cable Part no 14408 AXIS AFP MIO Coax User s Manual 13 Section 2 Installation and Configuration To install the AXIS AFP MIO interfa
41. the red indicator on the back pand will be lit T o prevent a possible timeout on the parallel printer port of your PC while waiting for the printer to finish IBM host printing and switch to PC mode use the following DO S command to set the timeout value to infiniteon your PC MODE LPT1 P Printer Memory A total of minimum 2 M bytes of memory is required in theH P printer 4 Requirements M bytes memory isrecommended to get good performance 4 M bytes is recommended as minimum memory resource for duplex printing Any additional upgrade to the memory will increase the performance of your printer InterfaceM emory A total of minimum 4 M bytes of memory is installed on the AXIS AFP Requirements MIO card The memory is used for software resident fonts and IPD S resources T hisshould be sufficient for most applications If you encounter a speed drop due to major IPDS resource downloading fonts overlays it can propably be solved by adding more memory to the AXIS AFP MIO T he added memory can be allocated for resource memory or interface output buffer by the Resource M emory Size option Note that for instance duplex printing uses the printer memory and not theAXIS AFP MIO memory In most cases adding memory to the printer it self has the greatest effect 10 AXIS AFP MIO Coax User s Manual Section 1 General Information Note Thememory SIM M modules used for the AXIS AFP MIO isthe same as for the printer it self Order the memo
42. tion after EPB nsn C24 AFEPB T his option is used in DSC D SE modes only when C16 0 Value C21 Form Feed at End of Print Buffer 0 If FF is the last character in the print order execute according to C21 Otherwise insert N L if not at position 1 1 Insert automatic FF if not at top of form Left Binding M argin sie astound icdiat ain C25 LBM U se this option to increase the left margin in all non IPDS coax modes T his option has no effect if COR is active Value C25 Left Binding Margin 0 999 Left margin increase in 1 100 inches 0 Default left margin increase Top Binding M argin EE eure tents IE IG TBM U se this option to increase the top margin in all non IPD S coax modes T his option has no effect if COR is active Value C26 Top Binding Margin 0 999 Top margin increase in 1 100 inches 0 Default top margin increase Cassette Link Control wack ER ER ai cee ere cree ate C27 LINK T his option cannot be controlled by the AXIS AFP MIO interface but must be activated in the native H P printer menus T he paper in the two trays must be of the same size in order for the linking to function AXIS AFP MIO Coax User s Manual 25 Section 2 Installation and Configuration C28 Coax Timeout css Ee ed Des ee es es ee C28 TIM E T his option controls when an IPD S job or a non IPD S job without End of Job or Form Feed information is forced to be printed and freeing the printer for other access Value C28 Coax Tim
Download Pdf Manuals
Related Search