User Manual
Contents
1. 2 Disclaimer e MbPIP 619 in vehicle terminal is developed based on the GPS applied technology of the United States Since its GPS receiver must always keep direct communication with the satellite in the course of operation the equipment may be affected when it operates in electromagnetic shielded areas or when the carrier such as a vehicle is under some shelters like indoors in the underground parking lot or under a footbridge e MbPIP 619 in vehicle terminal is a RF communication equipment The product shall be kept as far away as possible from areas that might lead to explosion like fuel warehouses chemical plants and so on The product may be affected in places sensitive to external radio frequency signals such as gas stations hospitals schools where radio frequency suppressors may be installed O Because data communication is conducted between the system adopting GSM technology and the monitoring center user must make sure the SIM card support GPRS data traffic offered by m China Aerospace Telecommunications Ltd the public communication network operators Besides the SIM card shall always contain sufficient fee Please do not use SIM cards subject to limitations of regions 3 Packing list and the optional accessories 3 1 Terminal standard configuration list Name Quantity unit Description Main unit 1 PCS GPS terminal Power cable 1 PCS GPS terminal power cable GPS MOUSE 1 PCS GPS MOUSE Multi fu2. m China Aerospace Telecommunications Ltd 7 3 Alarm SMS alert have set the user phone numbers When the device trigger the low voltage alarm SOS power failure alarm the terminal SIM card number will send the alarm SMS to the user phone numbers Example 12345 low voltage xx yy A V http maps google com q 38 870941 77 056114 12345 power failure xx yy A V http maps google com q 38 870941 77 056114 12345 S0S xx yy A V http maps google com q 38 870941 77 056114 7 3 1 Remote cut off electric amp restore Send a SMS command to the device SIM card number through any phone number Device will be cut off restore the ignition system SMS command format Remote engine off security key Engine off Remote engine on security key Engine on The function can be achieved through the platform the use of remote cut off please contact the service providers or distributor for technical support to ensure the safety 7 3 2 Restart Send a SMS command security key restart to the device SIM card number through any phone number Device will restart Reply restart ok If unsuccessful execution there is no any reply 7 3 3 SMS parameters setting e Set language Can send SMS command security key EN CN to set the language of device EN is English CN is Chinese For example SMS command 123456 EN Reply EN ok Set user phone number Send SMS command security key SP no1 no2 no3 to the number in device throu
3. there is much dust When washing the vehicle try to prevent the terminal from being soaked or showered to avoid damage to the terminal Keep using the in Vehicle terminal in normal temperature The equipment may be damaged when operating for long in an environment where the temperature is above 85 C or lower than 40 c When the vehicle is inside building tunnel or within a shielded area receiving of GPS signals and GSM communication network signals will be affected After the vehicle moves out of the area mentioned above receiving of GPS signals and GSM network will automatically resume The main unit has built in spare battery which will not be activated and begin working until the equipment is used for the first time and supplied with external power After the battery is activated when the external power supply is cut off the equipment will automatically switch to operate with power supply from the built in battery and the operation can last for about 10 hours calculated based on that the terminal data transmits once every 5 minutes The terminal equipment can use the accessories designated or recognized by CASTEL only Unauthorized accessories may damage the terminal equipment 20 D I China Aerospace Telecommunications Ltd 9 If abnormality occurs to the terminal equipment or its accessories thus leading to failure of normal operation please contact the manufacturer or the local dealer 10 2 Solution for
4. MPIP 619 User Manual REV2 0 3 7 CASTEL China Aerospace Telecommunications Ltd m China Aerospace Telecommunications Ltd Contents CONTENTS EE 1 Version Im Ornat I O nees Coeseselesusdees TEE vended Ruel OE tea dev iss 2 Scope Of application 4 ls Product introduction dende 4 25 DISCLAIMER ee 4 3 Packing list and the optional accessgoriesg nono nnnnnnnnnnnn nn nn n cnn nc nnann nes 5 3 1 Terminal standard configuration iert 5 3 2 Optional ACCESSOLLOS nadaa 5 AS SPEC Lal Words dis dilatan va 5 POSTOR datante a a EE 5 42 SSMS Command aana a a a ada 6 AD A EE 6 A A USEF phone Ad aaaea 6 AS Platform VA iba 6 Ds Terminal PELUCA asado 6 E Special UME IEN 6 5 1 1 Intelligent power Save E 6 e ale e DES 6 5 1 3 Maintenance amina ai 7 AO o e o 7 5 2 Positroning ANd TEACK 11S sde dee a 7 A A NN 7 A Tel 7 5 2 3 Fixed Upload E 7 5 24 Compress ed upload oerein arene eine eane Ra Ena EAER ETENE Eea E EEE AATRE 7 5 2 5 Real time MONItOriNg ccccccccccesssssssececececeesesneaecececscesseeaaeeeeeceseesesasaeeeesessseseaeaeeeeeens 7 e ME le H 5 2 7 Store and RE UplO ad iii ERREECHEN 7 5 3 Status detection and function Control 8 5 3 1 Vehicle status CEtectiOn 2 csseeivacacdesvacecesstccecdeesacacaae side iiid eiai eia edad idas 8 5 3 2 Read vehicle battery voltage 8 5 3 3 Remote cut off electric restore oooooooocccnonocacanononcnonnnnnnnnnnonn nn conan nn conan nn ronnnn nn nrnnnn nos 8 BoA Alarm
5. Re ee 8 5 4 1 Terminal alarmityDe cidad lied 8 542 A A aaa geese ei 9 5 4 3 SMS alarm Tomi ee EE 10 OS EI UA dd 10 6 1 SMS parameter T SOTT A dai 10 6 2 Castelecom Plis aia 10 6 3 Platform parameters setting 10 aS OMO EUG PA ONS tadas dui Does se cel gue Bo dee teo eo chee de td 10 Ted Phone Lcd a Gade eens Salers ales 10 ma China Aerospace Telecommunications Ltd dal OMS LOCA LO iaa dee 10 7 3 Alarm SMS alert have set the user phone mumbersi 11 7 3 1 Remote cut off electric Rrestore nn nccnnn nn nccnnn nn ncnnna nos 11 E A e d 11 R E Ke Een TEE 11 8 Technical specification amp interface Lpntroduction nn nn nccnan ns 13 Bl Techni Specification EE 13 8 2 Power able CAPI A ia ad 14 8 3 Multi function cable AP IND usada col 14 8 4 G Mouse interface C4PIN cccccsccscssesscssesscsessecscsscsecseesecssssecsesaeseessesecssssecsecaecaesaeesesaeeecseeaes 14 9 Tistallati n Guida egene eege eeh ea ARA dee ee 14 Ee e E 15 92 Placement OF MATO A Ee 15 9 3 Installation of GSM ASNO A a ii 15 9 4 G Mouse installation 16 9 5 HT 196R MSM EE 16 9 6 SOS button Asta la Mii dai 16 9 7 Relay Installation dia eet deed ue 17 9 8 Power cable and ACC cable connect 17 99 Finish installation 18 9 13 Status EE 18 9131 led INCI CACO iia ias 18 gas 2 AOS I sins 19 VO Mat a 111 E T Segoe ESA erdeelt Eed 20 10 1 Maritenance Instructigns esseere edeeedGeescensbixedh acia 20 10 2 Solution for troubleshoo
6. Remark in order to guarantee the safety if you sent the cut off command when ACC is ON engine ignition system can only be cuted off when the 619 device detect ACC change of the state from off to on 5 4 Alarm functions User can set whether to enable alarm and set the alarm thresholds by the platform When the device trigger the alarm alarm information will upload to platform within location data the alarm status in the location data will always be effective until the platform confirm the alarm e When the terminal have received the alarm acknowledge The alarm status in the location data no need to set as effective including door open close alarm SOS alarm ACC ON OFF acceleration deceleration quick lane changing sharp turn collision alarm e These alarms including idle engine GPS fault alarm temperature alarm fatigue driving alarm high speeding power cable cut off alarm low voltage alarm when the platform have confirmed them the alarm status in the location data should be set according to the real time vehicle status e The platform should response the device s alarm If the device don t receive the response the device will repeat 3 times every 1 minute but the high speed and high RPM only report times e All alarms trigger once upload once After upload the device alarm status automatically be cleared before the alarm status do not return to normal can t trigger the alarm again e The device will
7. ative law explicit or hinting data including but no limited in hinting selling data is no connection with accuracy and reliability Copy right reserved CHINA AEROSPACE TELECOMMUNICATION SLTD Unit710 711 7 F East Wing No 10ScienceParkWestAvenue Science Park Shatin New Territories Hong Kong 24
8. charges agreed jointly by the providers and users 5 Terminal product features 5 1 Special functions 5 1 1 Intelligent power save Device supports none power save mode and half power save mode After ACC turns off for 5 minutes device will upload the last available location At the same time device will disconnect GPRS stop supplying power to all peripheral unit and set GSM module to standby After device falls asleep it will be woke up by ACC on door open engine cut off SOS alarm called Then it will register GSM network and supply power to peripheral unit Once device log in platform it will upload above alarm including the latest available GPS location At the same time device will start upload regularly as preset time interval until next ACC off Terminal default mode is half power save you can set the mode by Castelecom PCTOOLS 5 1 2 Positioning Call the device user number or SMS to device user number After receives command from platform terminal will send GPS information for one time immediately m China Aerospace Telecommunications Ltd 5 1 3 Maintenance reminder User can set maintenance reminder from platform time or mileage Platform will calculate vehicles record and issue reminder once time or mileage condition are triggered 5 1 4 GPS Terminal can get locations globally by GPS technology 5 2 Positioning and tracking 5 2 1 Roll call After receives command from platform terminal will sen
9. ct the relay 85 with car battery anode e 87a 30 connect as below To GPS Tracker Relay CUT A Ignition System a TETERA O A Notice 1 please don t install this relay in the flameout magnetic valve in the diesel engines power supply circuit 2 please connect correctly the terminal ACC cable with the vehicle ACC 3 the above diagram is only for your reference Please chose the proper mode of the according to the different vehicle circuit 9 8 Power cable and ACC cable connect mia China Aerospace Telecommunications Ltd To vehicle battery or vehicle connection e In principle should not cut the original circuit loop except the Relay cut off cable connect 17 9 9 m China Aerospace Telecommunications Ltd Please make sure the main unit is insulated with the vehicle metal parts power cable SOS button or other cable should properly connect the battery positive negative The power cord fuse must be connected The terminal ACC detection cable should be connected to the vehicle ACC port otherwise the remote cut off electric operation maybe be invalid there is a hidden safe trouble 9 Finish installation After all equipment is installed please insert the fuse into the fuse seat and power on the main unit Meanwhile please start the vehicle to check if equipment works normally Upon finds any abnormality please turn off the main unit immediately and recheck all installation of wire
10. d GPS information for one time immediately 5 2 2 Timing track After receives command from platform terminal will send GPS information as preset communication channel time interval and duration 5 2 3 Fixed Upload The main unit upload the GPS information according to the time interval to the platform user can sent the time interval under ACC on or ACC off 5 2 4 Compressed upload Terminal uploads a package compressed by 8 pieces of time interval data to platform 5 2 5 Real time monitoring The vehicle terminal have the communication function update the information to platform server 5 2 6 Mileage statistics The device can read mileage information every 5s and then send the accumulative mileage to the server server 5 2 7 Store and Re upload When there s no GSM signal terminal will store the GPS information and upload them by sequence after GSM is connected Storage capacity of blind area s data is 3000 pieces ma China Aerospace Telecommunications Ltd 5 3 Status detection and function control 5 3 1 Vehicle status detection Device can detect ignition on off peripheral units connection and upload the abnormity 5 3 2 Read vehicle battery voltage Device acquires vehicle s battery condition every 2 seconds and upload the abnormity 5 3 3 Remote cut off electric restore When vehicle is confirmed to be stolen user can cut off engine ignition system from platform through 12V 24V relay Vice versa
11. d Red on3s Serious undesirable driving HT 196 CHT 196 behavior off No undesirable driving behavior 9 13 2 HT 196 beep Description remark power on Di last 500ms read RFID card Di last 500ms illegal card Di Di last 100ms interval 200ms no card reminder Di Di last 100ms interval 1s general undesirable driving behavior Di Di Di last 100ms interval 100ms serious undesirable driving Di Di Di Di Di last 100ms interval 100ms behavior High RPM Di Di Di last 100ms interval 100ms High speed Di Di Di last 100ms interval 100ms Fatigue alarm Di Di Di last 100ms interval 100ms Idle engine Di Di Di last 100ms interval 100ms 19 D I China Aerospace Telecommunications Ltd 10 Maintenance 10 1 Maintenance instructions 1 The voltage range of normal power supply for terminal is DC 9V 36V and the recommended operating voltage is 12V or 24V Prior to installation user shall make sure if the power supply falls within the range aforesaid When the in Vehicle terminal is powered on do not plug in or pullout the antenna or remove SIM card to avoid damage to the in Vehicle terminal and SIM card The connection socket of the in Vehicle terminal shall avoid direct contact with conductive body otherwise it may result in short circuit and danger Do not use the in Vehicle terminal in an environment where
12. er the steering wheel or at the 15 mia China Aerospace Telecommunications Ltd included angle inside the decorated plate under the front or rear windshield to ensure smooth transmission of communication signals Refer to the following diagram for the specific installation location 9 4 G Mouse installation G mouse can t be installed under metal baffle plate which will hinder the receipt of GPS signal thus affecting the normal monitoring and positioning of the MPIP 619 main unit G mouse is generally placed inside the decorated plate under the front or rear windshield or on the dashboard Refer to the following diagram for the specific installation location 9 5 HT 196R installation Please don t put HT 196R under any metal or explosion prevention metal user can attach it to the windshield or fix it under the windshield by double face adhesive tape Driving behavior analyzer should be kept horizontal and the angle with ground shall not exceed 15 degrees inclination 9 6 SOS button installation The SOS button should be placed between the dashboard and the steering wheel to facilitate operation of the driver The SOS button has adhesive tape stuck to its back User can remove the adhesive tape and attach it to the intended position Refer to the following diagram for the specific installation location 16 9 7 Relay installation O Connect the CUT1 control line of the multi function cable with relay s 86 pin O Conne
13. g Storage environment 40 C 85 C relative humidity 5 95 Not frosting Communication GPRS Quad band GSM 850 900 1800 1900MHz Position GPS GPS Sensitivity 159dB positional accuracy lt 15m speed accuracy lt 0 1m s Certification FCC CE E Mark HT 196R optional RFID attendance and driving behavior RFID frequency 125KHz Note Above current value is acquired by testing of 12V power supply with good network signal the actual current may be different according to local circumstance 13 D I 8 2 Power cable 4PIN China Aerospace Telecommunications Ltd overview function PIN color Function description TXD 1 Brown GND 2 Black DC 9 36V 3 Red Connect the power cable RXD 4 Orange 8 3 Multi function cable 4PIN f Pin cable overview Pin mark Pin Function description color ACC 1 Gray ACC detection CUT purple Control output1 GND Blue GND SOS 4 white SOS input signal detection 8 4 G Mouse interface 4PIN overview Function Pin Remarks TXD DC5V output 1A max 2 GND 3 RXD 4 Standard RS232 connect G mouse or HT 196R if connect the configur ation cable please exit the serial m ode after you set the parameters by the PCTOOLS 9 Installation Guide WARNING below operation are for reference we suggest the device to be i
14. gh a ny phone When some position phone is not needed to set pls write nothing in this po sition Specially send SMS security key SP to clear all of user phone numbers For example SMS command 123456 SP 13600000001 Reply SP 13600000001 ok 11 m China Aerospace Telecommunications Ltd SMS command 123456 SP Reply SP ok Set GPRS parameters Send SMS command SMS security key SG DialMode P Domain Port APN user passwor d to the number in device through any phone DialMode 0 express domain mode 1 express IP mode For example SMS command 123456 SG 0 www freelivetrack com 16190 cmnet Reply SG ok 12 D I China Aerospace Telecommunications Ltd 8 Technical specification interface introduction 8 1 Technical specification Item description Dimension 75mm L 48mm W 20mm H Weight 80g IP rate IP54 Shape Aluminum alloy Working Voltage DC9V 36V Battery 3 7V 500mAH Lithium battery Standby current 40mA Normal working current S85mA 13 8V no including accessory Max working current lt 250mA013 8V no including accessory Current when data transmission lt 150 mMA 13 8V no including accessory Current when ACC OFF lt S90mMA 12V 24V no including accessory Power saving mode sleep mode lt 20mA012V 24V no including accessory Working environment 30 C 70 C relative humidity 5 95 Not frostin
15. n preset threshold default setting is close Geo fence Trigger when the vehicle enter or exit the preset area can set by the platform alarm rectangle circle polygon area up tO 64 area supplied by the platform Route offset alarm The terminal upload the positioning data the platform automatically determine whether conform to the default preset route on the platform supplied by the platform Road speed limit The terminal upload the positioning data the platform automatically determine whether conform to the default preset road speed limit on the platform supplied by the platform 5 4 2 HT 196 alarm type Alarm type Description ue built in G sensor 3 axis acceleration sensor chip when over the alarm threshold the collision device will send alarm to platform Seana built in G sensor 3 axis acceleration sensor chip when over the alarm threshold the arp turn p device will send alarm to platform built in G sensor 3 axis acceleration sensor chip when over the alarm threshold the Accelerate device will send alarm to platform built in G sensor 3 axis acceleration sensor chip when over the alarm threshold the Decelerate q device will send alarm to platform quick lane built in G sensor 3 axis acceleration sensor chip when over the alarm threshold the changing device will send alarm to platform m China Aerospace Telecommunications Ltd 5 4 3 SMS alarm reminder De
16. nction cable 1 PCS GPS terminal multifunction cable Installation kit 1 set Including fuse Velcro cable tie 3 2 Optional accessories Name Quantity unit Description USB setting cable 1 PCS CASTELECOM PC Tools setting cable SOS button 1 PCS SOS button Relay 1 PCS 12V or 24V optional remote electric cut off Driving behavior inbuilt GPS GPS functions acceleration deceleration quick lane changing sharp HT 196R 1 PCS turn collision buzzer and light instructions RFID optional alternative between G mouse and HT 196R 4 Special words 4 1 position data the datagram including location alarm status which the terminal send to the platform m China Aerospace Telecommunications Ltd 4 2 SMS command Send to device SIM card number including the read and setting parameters the device SIM card should have SMS function 4 3 Security key The key is the legality of the SMS command validation The length of the key is fixed 6 characters default is last 6 number of the device serial number can modify Please get more details from platform operator 4 4 User phone number For receiving the SOS alarm low battery voltage alarm power off alarm 4 5 Platform service Platform service providers Platform paid for the computer automation and artificial service convenient for users to get vehicle information such as location alarm status The service content and the
17. nstalled by professional engineer CASTEL will not take responsibility for any vehicle circuit fault caused by user s operation 14 L I China Aerospace Telecommunications Ltd 9 1 SIM card installation Insert the SIM card before installation of the main unit The installation processes of SIM card are below Open the side plate of the main unit with screw driver make sure the switch to off before inserting the SIM card O Insert the SIM card to the card seat then put the switch to ON side e Fix the side plate to the main unit fasten the screw Notice please make sure the SIM card have SMS and GPRS function 9 2 Placement of main unit e The location for placement of main unit should be determined in advance The location should allow secure installation concealment anti humidity avoidance of high temperature area and be far away from magnetic field air bag sound system ABS system and other sensitive electronic equipment In addition it should be installed snugly o O Recommended installation location the concealed position inside the decorated board under the dashboard or under the seat Refer to the following diagram for the specific installation location recommended installation location 9 3 Installation of GSM antenna GSM antenna is installed at a concealed place inside the vehicle but the place should not be closed too much Generally it is placed inside the decorated plate und
18. rted Solution analyze why the MPIP 619 main unit won t come online 21 m China Aerospace Telecommunications Ltd 3 Failure of the MPIP 619 main unit Solution send it to the designated maintenance center for repair 22 ma China Aerospace Telecommunications Ltd 10 3 Warranty card Warranty Card User Name Contact Phone Contact Address Post Purchase time Device series NO Agency and phone No Note Remark Please keep this card properly for get better after service Details please see below information Agency stamp Repair record Device Model Reason and status record Date Repair man Customer Repair reason Record 23 m China Aerospace Telecommunications Ltd Note Agency should fill this card completely when repair 11 Claim Without written authorization of CHINA AEROSPACE TELECOMMUNICATIONS LTD any kind of copy transmission dispatching or saving of this file is prohibited CHINA AEROSPACE TELECOMMUNICATIONS LTD keeps the rights of reservation and modification without any notification in advance Receiving and operation time would be affected by SIM card network and using circumstance of different device And we don t take responsibility of data losing and income wastage or any special occasion indirect reason This file is based on local situation In spite of rel
19. s or send it to a professional vehicle service center to check Log on the platform to check if the vehicle is normally online and the positioning is proper If there are problems please refer to the User Manual for trouble shooting Finally please contact the local dealer if the problems cannot be solved 13 Status 9 13 1 led indicator Type Color Definition of status remark Power on RED Fixed on working normally the device Off power off Off sleep mode or no power GSM on the device Blue Flashing Registered successfully On Registering Off sleep mode or no power GPS on the f green Flashing GPS located device On search GPS information GSM Off sleep mode or no power On the SOS SOS red Flashing Registered successfully button button oe On Registering GPS Off sleep mode or no power green G MOUSE G Mouse Flashing GPS located 18 D I China Aerospace Telecommunications Ltd On search GPS information Red on search GPS information GPS Green on GPS 3D located Red yellow amp green HT 196 CHT 196 Yellow on GPS 2D located Off sleep mode or no power Flashing on 250ms off 250ms No ID card or illegal ID card RFID Yellow On 1s Searching for ID card HT 196 CHT 196 Constantly on ID card detected Off power off within power on 1 minutes or RFID power supply abnormity Yellow on 3s General undesirable driving Driving behavior Behavior Yellow amp Re
20. send the SOS alarm max 5 times every 1 minute when the device don t get the platform s response 5 4 1 Terminal alarm type Alarm type description D I China Aerospace Telecommunications Ltd SOS It will trigger SOS alarm when user presses SOS button for more than 3 seconds Low voltage Terminal automatic detect the external power supply trigger when the external alarm voltage is less than 10 5V 12 v model or 21V 24v model default setting is enable Power failure power cable cut off alarm In built backup battery trigger when the external voltage is less than 8V and automatic switch to backup battery supply default setting is enable Trigger when the G mouse or HT 196 failure or trigger when don t receive the GPS GPS failure information in 2 minutes default setting is enable Trigger when the vehicle speed is more than the preset threshold for 60 seconds Speed alarm default setting is enable speed threshold is 120Km h detecting time is 60 seconds 0 300 seconds optional ACC ON trigger when the ACC status changed from off to on last 2 seconds on the ACC on off contrary trigger the ACC OFF alarm default setting is close fatigue driving Trigger when the continuous driving time is more than the preset threshold the alarm information include the continuous driving time and the threshold default setting is close idle engine Trigger when the idle time is more tha
21. ting cccccccecsssssececccecsesesenceceecescseseneceeeeeesesesennceeeeeeeesenens 21 10 3 Warranty CAR EE 23 lis GARE 24 Version information D I China Aerospace Telecommunications Ltd version editor date Modified clause V1 0 0 Kang kuan ming 2014 08 06 Artificial V1 0 1 Didi 2014 8 7 And the power cable description V2 0 1 Liu yunfei 2015 02 06 Modify the led indicator status description Modify the relay connect way and description V2 0 3 Liu yunfei 2015 09 21 Modify the GSM indicator color m China Aerospace Telecommunications Ltd Scope of application This user manual is applicable to MPIP 619 vehicle terminal product 1 Product introduction MPIP 619 in vehicle terminal integrates internationally leading technologies of GPS GSM intelligent automatic control and anti theft alarming It is able to monitor the position safety operation and technical status of the moving target 24 hours a day and it can provide you real time tracking fleet management anti theft of vehicle asking for help in case of accident fault repair data checking fuel consumption statistics mileage statistics maintenance reminder driving behavior analyzer RFID attendance statistics SMS alarm Geo fence alarm easy installation read the total fuel consumption read the fault alarm read the engine speed alarm and temperature alarm etc Note some function shall be required to purchase some accessories
22. troubleshooting Failure Analysis of possible causes and solutions The equipment won t come online 1 The fuse of the power cord is burned so that there is no power supply Solution change fuses 2 Improper setup of parameters Solution check APN setting parameters and set up them again 3 Insufficient value installed for SIM card onion support of GPRS function Solution reconfirm the SIM card function 4 Improper connection of GSM antenna and weak signal Solution check the GSM antenna 5 Failure of the MPIP 619 main unit Solution send it to the designated maintenance center for repair The equipment does not position the vehicle 1 G mouse is shielded by metal shielding object Solution remove the metal shielding object or reinstall G mouse at another place 2 G mouse failure Solution return it to the designated maintenance center for repair 3 Failure of the MPIP 619 main unit Solution send it to the designated maintenance center for repair Power cut off alarm occurs 1 Fuse of the power source is burned Solution change fuses 2 The power cord is improperly connected with the ACC end Solution check the connection and reconnect it tithe common power cord Fail to report the emergency alarm 1 The SOS button has not been connected Solution check the SOS button 2 The MPIP 619 main unit won t come online so that the alarm information fails to be repo
23. vice sends SMS to user phone number when alarm occurs including SOS alarm power supply off alarm low voltage alarm and vehicle trouble 6 Setting guidance Terminal parameters can be set by Castelecom PCTools platform and SMS 6 1 SMS parameters setting Any mobile number can send the SMS command to the terminal SIM card number to read and set terminal parameters 6 2 Castelecom PCTools Please download the castelecom PCtools from the website http www castelecom com pc tools 6 3 Platform parameters setting Terminal have connected the platform please get the account and password from platform operators Then you can read and set the parameters The platform website http www freelivetrack com T SMS functions 7 1 Phone location Dial the SIM card number in device and hang up the call in 6 seconds before it is caught then device will send a message with location information to initiator User can check location on map by clicking the linkage in message Example A12345 xx yy A V http maps google com q 22 7643750 114 3974383 xx CSQ value yy number of valid GPS stars A V A valid location V void location 7 2 SMS location Send a SMS command security key LBG to the device SIM card number through any phone number Device will reply a location SMS to the sender phone The location SMS includes Google map link example A12345 xx yy A V http maps google com q 22 7643750 114 3974383 10
Download Pdf Manuals
Related Search