user MANuAL
Contents
1. FIELDVISION OCM 7B D 7 ON CAMERA MONITOR MANUAL elvid INTRODUCTION hank you for choosing Elvid he Elvid OCM 7B D FieldVision is an on camera monitor with HDMI and composite audio and video inputs as well as composite video loop through The 7 LED panel s native resolution is 024 x 600 with an aspect ratio of 16 9 native that you can set to 4 3 The onscreen menu makes it easy to fine tune your image offering adjustments for brightness contrast hue and saturation There are also broadcast specific features like safety rame markers and multiple display formats he FieldVision is equipped with advanced tools like Check Field to help calibrate the monitor a Focus setting to fine tune your ocus and Camera mode to scale the incoming video signal when shooting on a DSLR Onboard buttons provide quick shortcuts o Camera Focus and Check Field modes the safety frame and center markers and the onscreen volume bar There s also an integrated speaker and a 3 5 mm stereo headphone output for ive audio monitoring PRECAUTIONS Exposure to high sound levels can cause permanent hearing loss Avoid listening at high volumes for extended periods of time Keep this product away from water and any flammable gases or liquids Do not expose this product to humidity or extreme heat or cold Make sure this product is powered off when plugging it into a power source Use only the correct reco2. IN THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS WARRANTIES NOR ANY MPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO ANY MPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE This warranty provides you with specific legal rights and you may also have additional rights that vary from state to state o obtain warranty coverage contact the Elvid Customer Service Department to obtain a return merchandise authorization number and return the defective product to Elvid along with the RMA number and proof of purchase Shipment of the defective product is at the purchaser s own risk and expense For more information or to arrange service visit www elvidcinema com or call Customer Service at 212 594 2353 Product warranty is provided by the Gradus Group www gradusgroup com Elvid is a registered trademark of the Gradus Group 2014 Gradus Group LLC All Rights Reserved G k A Gradus Group Brand www elvidcinema com
3. The center marker will not display at the same ime as the menu Camera Camera mode scales the incoming video signal to fill he screen This is useful when shooting on a DSLR You can urn this mode on or off SOUND MENU Volume Adjust the monitoring volume of the FieldVision from O to 100 Focus Use this setting to check the areas of the image that are in focus Activating this setting increases the sharpness and contrast of the monitor and displays in focus areas of the image with sharpening artifacts USING THE BUTTONS For greater efficiency while using the FieldVision you can use the buttons on the front of the monitor as shortcuts to various functions instead of cycling through the onscreen menus Camera Button Press this button to enable or disable Camera mode Scale Button The Scale button displays and adjusts the size of the onscreen safety frame markers Press the button repeatedly to cycle through the options 80 85 90 93 96 and off Left Button When the menu is closed out press the Left button to display the center marker Right Button When the menu is closed out press the Right button to display the onscreen volume bar When the volume bar is onscreen use the Left and Right buttons to adjust the monitoring volume from 0 to 100 To exit the volume bar press he Menu button Down Button When the menu is closed out press the Down button to enter Focus mod
4. e Up Button When the menu is closed out press the Up button repeatedly to cycle through the Check Field modes red green blue and mono elvid SPECIFICATIONS Panel Size Panel Type Backlight Resolution Brightness Contrast ratio Viewing angle Dot pitch W x H Display ratio Input Output 7 TFT LED 1024 x 600 250 cd m 700 1 U D 70 75 0 05 x 0 15 16 9 RF HDMI composite video mono audio Composite video headphone 3 5 mm stereo mono speaker Supported formats 50 60 Hz Threaded socket Input voltage Power consumption Battery type Dimensions Lx W x H Weight 480i 480 720p 108 1 4 20 6 to 24V lt 6 W Canon LP p 576i 576p Oi 1080p DC E6 7 4 x 5 3 x 2 0 18 9 x 13 4 x 5 cm 1 Ib 0 5 kg The FieldVision will not turn on The FieldVision is turned on but there is no onscreen image or the image is weak If you are powering the FieldVision with a battery make sure the battery is fully charged and properly seated in the battery plate Make sure that the 12 V DC adapter is fully plugged in and that your AC power source is reliable Try switching AC power sources Make sure the FieldVision is not in standby mode See Powering the FieldVision on page XX for further reference Make sure the HDMI or composite video cable is securely plugged into the proper input connect
5. ese Korean Russian and Portuguese H Position Adjust the horizontal position of the onscreen menu V Position Adjust the vertical position of the onscreen menu OSD Timeout Use this setting to set the length of time the onscreen menu is d isplayed You can choose from 5 to 60 seconds in 5 second intervals or you can disable the feature so the menu remain out The default se s onscreen until you manually close it ing is 10 seconds Transparent Set the menu s level of opacity You can adjust this setting from 1 to 7 with 7 being the most transparent The default setting is off which makes the menu opaque FUNCTION MENU Reset Restore the FieldVision s menu to the factory default settings System Select the transmission display format You can choose NTSC M default PAL M NTSC BG PAL N NTSC DK PAL DK PAL or SECAM BG Display Ratio You can set the aspect ratio for the onscreen image The options are 16 9 and 4 3 The default setting is 16 9 which is the FieldVision s native aspect ratio The 4 3 setting will scale the image to fit that aspect ratio Screen Markers You can set the FieldVision to display an onscreen box as a safety frame marker at a set percentage of he screen size You can set this to 80 85 90 93 96 or off The screen marker will not display at the same time as he menu Centre Markers This setting displays a marker in the center of the screen
6. ion on the FieldVision and that the input mode is set correctly Try pressing the Mode button to set the input mode Make sure the monitor is set to the proper input mode If you are powering the FieldVision with a battery make sure the battery is fully charged and properly seated in the battery plate continued The screen displays only a black and white image The onscreen image size is incorrect If you are powering the FieldVision via AC power use only the supplied 12 V DC adapter Check your cables to make sure hey are reliable Check the brightness contrast hue and saturation settings and adjust as necessary Make sure Check Field mode is urned off Make sure that Camera mode is disabled Check whether the aspect ratio is set correctly Make sure that the correct input signal is selected Check your cables to make sure they are properly connected and that they are reliable The FieldVision is emitting a high pitched whine feedback There is no sound The images are not synchronized e Turn the monitor s volume all the way down or plug headphones into the headphone jack ncrease the monitoring volume f you are using the FieldVision as a wired standard definition video monitor make sure your composite audio cable is fully plugged into the composite audio input SC and PAL settings may not be correctly set Make sure the mon
7. itor s display format matches that of the input Refer to System under Function Menu on page XX or further reference NOTES FCC STATEMENT This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FE ONE YEAR LIMITED WARRANTY his Elvid product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one 1 year from the original purchase date or thirty 30 days after replacement whichever occurs later The warranty provider s responsibility with respect to this limited warranty shall be imited solely to repair or replacement at the provider s discretion of any product that fails during normal use of this product in its intended manner and in its intended environment Inoperability of the product or part s shall be determined by the warranty provider If the product has been discontinued the warranty provider reserves the right to replace it with a model of equivalent quality and function his warranty does not cover damage or defect caused by misuse neglect accident alteration abuse improper installation or maintenance EXCEPT AS PROVIDED HERE
8. lable battery type that you may already own For more information on compatible battery types refer to Speci fications on page XX To install a compatible battery follow these steps 1 Place a compatible battery in the battery plate Make sure the battery s bottom contacts are aligned with the contacts in the battery plate 2 Slide the battery forward until it locks into place To turn on the FieldVision press the power switch to the On position The FieldVision will turn on and enter standby mode and the power indicator LED will glow red Press the Power button to enter ready a mode The power indicator LED will turn green and then glow red USING THE OCM 7B D MOUNTING THE FIELDVISION Use the FieldVision s 1 4 20 threaded socket to attach the monitor to your mounting system Make sure your bracket can support the monitor CONNECTING THE VIDEO SOURCE HDMI Input The FieldVision is equipped with an HDMI input for use as a wired high definition video monitor Use the a compatible HDMI cable to connect your HDMI video source to the FieldVision s HDMI input and then press the Mode button to cycle through the input modes until HDMI appears on the monitor If your HDMI video source is sending a signal to the monitor the image will appear onscreen and the power indicator LED will glow green Composite Video Input The FieldVision also ha
9. mmended voltage Do not attempt to disassemble or repair this product Do not place or store the FieldVision acedown since this can damage the screen Handle this product with care Avoid any unnecessary impacts to this product Do not block the vents in this product Disconnect this product from its power source before storage and during electrical storms Do not use chemical solutions to clean this product Clean it with only a soft dry cloth Keep this product away from children Make sure that this product is intact and that there are no missing parts To avoid damage to this product be careful not to overtighten or improperly thread any of the threaded fittings All photos are for illustrative purposes only TABLE OF CONTENTS Product Contents seso 6 DVervieW aaa 7 8 Powering On and Off 9 10 Using the OCM 2B D nicas 11 12 The Sunshade ieem tad 13 TPS cria a 4 Color Menu 15 OSM res u u mau 6 A e mnan 7 Sound Menu 18 Using the Buttons 9 SPECINCaLIONS L UU rita traida iaa 20 21 Troubleshooting 22 24 Notes aos 25 5 a 26 ai 27 PRODUCT CONTENTS 7 On Camera Monitor Mini HDMI to HDMI cable User manual Shoe mount ball head Sunshade 12 V DC adapter NOTE Additional battery plates and or battery adapters compatible with
10. other popular brands can be purchased by visiting www elvidcinema com OVERVIEW Sunshade slots elvid wer scae UP MODE POWER Headphone jack Power button Screen Status LED Camera button Mode button Scale button Up button Left Nav Down button Menu button Right Nav Speaker Battery mounting plate 1 4 20 Threaded socket Power switch Composite video output HDMI input Power Switch Composite video input Audio input POWERING ON amp OFF There are two ways to power the FieldVision AC or a Canon LP E6 battery AC POWER To run the FieldVision via AC power use the included 12 V DC adapter to connect the FieldVision s DC power input to your AC power sour ce To turn on the FieldVision press the power switch to the On position The FieldVision will turn on and enter standby mode and the power indicator LED will glow red Press the Power button to enter ready mode The power indicator LED will turn green and then glow red CAMERA BATTERY The FieldVision s bu ilt in battery plate accommodates a Canon LP E6 battery This allows you to power the monitor with a read ily avai
11. s are located in the left column of the main menu window Note The menu is accessible only when the FieldVision is receiving a video signal NAVIGATING THE MENU Menu Button Press the Menu button to access the menu return to the previous menu or screen without making a selection or close out the menu Up and Down Buttons When the menu is open use the Up and Down buttons to navigate the menu or adjust the value of a vertical submenu item Left and Right Buttons When the menu is open use the Left and Right buttons to enter a submenu adjust the value of a horizontal submenu item or make a selection in a vertical submenu COLOR MENU In the Color menu you can adjust brightness contrast hue and saturation of the monitor from 0 least to 100 brightest Check Field In Check Field mode only the selected color will appear onscreen You can select red green blue or mono In mono a grayscale image will appear onscreen Check Field mode is useful for calibrating the monitor Color Temp When using the FieldVision as a wired HDMI monitor You you can select from the presets 9300 7500 and 6500 K You can also configure your own custom setting which is labeled User in the Color Temp menu Customizing the color temperature is recommended only for advanced users OSD MENU Language You can set the onscreen language to English fied default Simp Chinese French Italian German Spanish Japan
12. s a composite video input for use as a wired standard definition video monitor Use a compatible cable to connect your composite video source to the FieldVision s composite video and audio inputs and then press the Mode button to cycle through the input modes until video appears on the monitor If your composite video source is sending a signal to the monitor the image will appear onscreen and the power indicator LED will glow green Note Your audio source must be plugged into the FieldVision s composite audio input in order to monitor the sound Loop Through The FieldVision offers composite video loop through also known as pass through To loop the video signal through the monitor make sure the FieldVision is receiving a video signal from your composite video source and then connect a compatible cable to the output connection on the monitor THE SUNSHADE The sunshade prevents glare on the monitor s screen by blocking out stray light and is useful when shooting outdoors 1 Insert the sunshade s pegs into the monitor s sunshade slots 2 Slide the sunshade down until it locks into place To deploy the sunshade fully open its lid and wings THE MENU Before using the FieldVision make sure the monitor s settings are properly configured All of the setting configurations are located in the main menu which has four submenus Color Onscreen Display OSD Function and Sound The submenu
Download Pdf Manuals
Related Search