GrooveMove Instruction Manual
Contents
1. Read all safety amp operating instructions before use amp take notice of all warnings Follow all operating instructions and retain for later use Do not use this speaker system near water or moisture Clean only with a dry cloth Do not block any of the ventilation openings in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other speaker systems including amplifiers that produce heat 7 Protect the power cord from being walked on or pinched particularly at the plugs convenience receptacles and the point where they exit from the speaker system Only use the attachments accessories specified by the manufacturer Unplug all electrical components during lightning storms or when unused for long periods of time Do not attempt to service the dock yourself Refer all servicing to a qualified service professional Servicing is required when the dock has been damaged in any way i e power supply cord plug is damaged liquid or objects or have fallen inside the dock the dock has been exposed to rain or moisture the dock has been dropped or does not operate normally op wn io so o e Oo A Speaker unit front A1 5 roan rs A1 A3A4 A5A6 A7A8 A9A10 A2 A13 A1 set A2 vol A3 timer A4 time set A5 dimmer A6 al set A7 alt al2 A82. wheel to adjust the hour or minute setting Pressing the Time Set button a third time will exit this function Alarm and Alarm Mode Setting Press the all al2 button to enter the alarm setting mode A small bell with a number 1 will appear in the right hand corner of the display Press the Al Set button to set the alarm time Adjust the hour first by rotating the set wheel Press Al Set again to adjust the minutes and rotate the set wheel up or down Press all al2 once more and a bell with number 2 will appear Repeat process to set alarm 2 if desired After setting the alarm times press all al2 button again to turn on Alarm 1 Alarm 2 or both the bells with the numbers will indicate which alarm you have chosen After you set the alarm s press al mode to switch between RADIO IPOD AUX SOUND BEEP as the alarm type Please note Your iPod needs to be docked to see the IPOD as an alarm selection If you choose to wake up to the nature SOUNDS make sure the unit power is on Press the Sounds button to cycle between field daybreak water or ocean Pressing the Power button will exit but will ensure the alarm is set To set the volume of the alarm see Volume Setting section Snooze Nap Mode Setting Snooze Nap Pressing the snooze nap button after the alarm rings will turn off the alarm in nine minute intervals Nap Mode Setting To change the Sno
3. GrooveMove Instruction Manual Cygnett 12 month manufacturers warranty Register online at www cygnett com to activate your warranty For product support please contact Cygnett directly at info cygnett com For the latest news and more cool products visit the website www cygnett com Cygnett www cygnett com GrooveMove Speaker system amp alarm clock for iPod O Made for a iPod OPERATING INSTRUCTIONS Contents Introduction What s in the Box Caution Safety Instructions Connecting the GrooveMove Operating the GrooveMove Audio Modes Setting the Time Alarm and Alarm Mode Setting Snooze Nap Mode Setting Sleep mode setting Tuning the Radio Volume Setting Setting the Back light Changing Alarm Volume Operating the GrooveMove via Remote Control Product Specifications Introduction Thank you for purchasing Cygnett s GrooveMove Speaker system amp alarm clock for iPod This all in one compact iPod speaker system amp alarm clock gets you moving day or night Customise your morning wake up call iPod playlist AM FM radio buzzer or one last snooze To get the most from your new GrooveMove please take a few minutes to read the following instructions and familiarise yourself with the operation of the unit What s in the Box 1 GrooveMove iPod speaker system amp alarm clock 2 AC DC Power Adaptor 3 Remote Control 4 3 5mm jack cable for auxiliary input Caution Safety
4. al mode A9 sounds A10 audio A11 power A12 open A13 snooze nap B Speaker unit rear B1 B2 B3 B1 fm B3 dc in B2 line in B4 LCD display Connecting the GrooveMove Take the AC Power Adaptor and plug it into the GrooveMove 12v DC IN Port at the back of the unit Plug the AC Power Adaptor into the wall socket and switch it on Press the Power button located on the top of the GrooveMove The unit should now be on and ready for use Please note The unit will have default settings of AUX mode 20dB volume and the LCD will display a time of 12 00 Note Two AA batteries will also power the clock and alarm set functions batteries not included Operating the GrooveMove Audio Modes AUX RADIO IPOD When the GrooveMove is turned on it will be in AUX audio mode To listen to your iPod dock your iPod on the top of the unit Press the Audio button on the top of the unit and click through AUX RADIO IPOD audio modes until you have reached the iPod mode To listen to the radio or another Auxiliary input press the Audio button on the top of the unit to choose between AUX or RADIO modes Setting the Time Press the Time Set button located on the top of the unit to select the Hour Minute settings Pressing the Time Set button once will adjust the hour and pressing it twice will adjust the minutes Then rotate the set
5. oze Nap intervals put the unit in power off mode Press the snooze nap button to select a nap period of 10 20 30 40 50 or 60 minutes The unit will power on and your chosen sound will activate after this time Sleep Mode Setting The sleep mode allows you to set the unit to turn off the music after a certain amount of time 10 20 30 40 50 60 70 80 or 90 minutes Turn the unit ON Press the timer button on the top left of the unit and the display will cycle through 10 20 30 40 50 60 70 80 or 90 minutes time options Select the time you desire and the GrooveMove will turn off after the desired sleep time selected Tuning the Radio In the power ON mode press the audio button to cycle through to radio mode and use the set wheel to adjust the FM frequencty Volume Setting To increase the volume spin the volume wheel clockwise To decrease the volume spin the volume wheel anti clockwise Maximum volume is 40dB Setting the Backlight Press the Dimmer button to change the brightness of the backlight Changing Alarm Volume Set the desired volume before turning the unit into standby mode Volume will start at level 5 and increase to the level previously set Operating the GrooveMove via Remote Control The remote control can be used to control both your iPod when docked and the GrooveMove Please see the functions of the remote below power power on off sounds bu
6. tton to choose nature sounds o audio button to choose audio sources timer button to choose sleep time time set button to set time menu to go back to menu function for iPod enter go to the function you choose al set button to set alarm alarm1 2 button to set alarm 1 or 2 al mode button to set alarm music Q vol q vol dimmer button to change brightness of LCD snooze nap under the alarm mode press this button the alarm will be ring again after 9 minutes In power off mode press snooze nap button 1 2 3 4 5 6 times to postpone alarm 10 20 30 40 50 60 minutes m4 prev go to previous song next go to next song Cygnett a v up down button to select the function menu use a up down button Product Specifications play pause press to start playback press again to pause Recharge iPod Dock and play directly Built in FM radio function LCD display for time Output power 8Wx2
Download Pdf Manuals
Related Search