Pipa - Nuna
Contents
1. Shoulder Height shoulders must not be above the marker line See page 13 Harness Straps must not be twisted See page 14 Harness Buckle must always be securely fastened See page 10 Child position child must be in full contact with back of restraint Harness Tension See page 9 pull harness tight Suitable clothing child s clothing See page 10 must not interfere with the harness See page 11 Quick Reference Restraint and Base IMPORTANT After reading this Quick Reference read the following instructions carefully Tether Strap must always be Carry Handle must always be used when the restraint is locked into position installed in a vehicle Store end See page 19 of tether in bag See page 26 9 Secure latching restraint must be securely latched into base See page 25 Vehicle Belt must always be secure and pulled tight See page 23 amp 24 Base Recline adjustment base must be reclined correctly See page 22 Use the restraint exactly as shown in the instructions Supervision of children is needed because they may be able to undo buckles To ensure that baby s back is evenly supported do not put more than one nappy on the baby and make sure the nappy is not folded thickly at the back Do not allow the restraint to come into contact with polishes oils bleach and other chemicals Destroy the restraint if it has been in a severe crash even if no damage2. Thanks for choosing Nuna Nuna designs distinctive smart exciting products DO NOT USE THIS CHILD RESTRAINT UNTIL YOU HAVE READ AND UNDERSTOOD THE INSTRUCTIONS IN THIS USER GUIDE AND IN YOUR VEHICLE OWNERS MANUAL Enjoy your Infant Car Seat INNIINO Quick Reference 1 amp 2 WARNINGS 2i ien rr radi 3 amp 4 gut 5 amp 6 Additional Warnings 7 amp 8 Securing Child in the Restraint 9 11 Shoulder Strap Height 12 14 ACCOSSONIOS si veces icr irai riae rias 15 17 lifant Insert err 18 Handle 22 19 The Next Restraint eene 20 Installation General 21 Installation Base 22 24 Installing Restraint sees 25 Tether Strap Use 26 Installation Tether Anchorage 27 29 Use with Strollers eee 30 Cleaning and Maintenance 31 32 Quick Reference Use IMPORTANT After reading this Quick Reference read the following instructions carefully Shoulder Straps must always Head Liners and Infant Insert be at correct height and pulled only use for smaller children tight who require more support See page 12 14 See page 18
3. the top 26 Installation Tether Anchorage Always connect the snap hook securely to the anchor age fitting Adjust the tether tension until the webbing is pulled tight but not so tight that it is lifting the child restraint off the vehicle seat The anchor fitting must be aligned as shown unless stated otherwise in the vehicle owners handbook If drilling a new hole select a position on the centre line of the seating position and no closer than 100 mm from the front edge of the parcel shelf centre line of seating position Installation Tether Anchorage If the car is fitted with a child Attachment restraint anchorage point P d Bolt Lock Locate the anchorage point Tdi behind the rear seating iti Anchor position consult the vehicle Fitting owners handbook for loca P d tion of the anchorage point Spacers Remove the thread plug from if the parcel shelf floor roof and P di required install the attachment bolt as shown opposite Vehicle LT Bc Trim CAUTION A Vehicle DO NOT OVERTIGHTEN THE Metal ATTACHMENT BOLT MAXI _ Structure MUM TORQUE 20Nm i 4 FRONT OF VEHICLE Installation Tether Anchorage If the car is not fitted with a child restraint anchorage point For sedans only drill 9 mm hole in the parcel shelf on the centre line of the seating posi tion as shown on page 27 Install the anchor bolt as shown o
4. long enough to secure the child restraint Read carefully the whole of the instructions for the installation and in the event of doubt about the method of installation consult the child restraint manufacturer or agent or a child restraint fitting station authorized by the relevant transport authority or in New Zealand consult the agent for the vehicle Features Child Restraint 1 Carry Handle 9 Harness Straps 2 Infant Insert 10 Seat Cover 3 Shoulder Pads 11 Stroller Release Handle 4 Buckle and Crotch Belt only used with infant car 5 Harness Adjuster Button seat adapters 6 Harness Adjuster Strap 12 Shoulder Strap Slots 7 Canopy 13 Base Attachment Bars 8 Carry Handle Lock 14 Splitter Plate Features Base 15 Tether Strap 21 Instruction Manual Storage 16 Child Restraint Release 22 Recline Adjustment Lever 17 Tether Strap Anchorage 18 Rebound Bar 19 Vehicle Belt Lock Off 20 Level Indicator Bubble When baby is in the restraint ALWAYS secure the harness and adjust to a firm fit Always check buckle and other parts for hot surfaces A carrier left uncovered in the sun could burn a child Cover with blanket if leaving in car Do not use child restraint if any harness straps are cut frayed or damaged Do not use any products or accessories in conjunction with child restraint not supplied with child restraint Fall hazard Child s movement can slide carrier NEVER place carrier near edges o
5. e metal splitter plate Shoulder Strap Height 3 Pullloose end of harness loop out through slot and z place in correct slot 4 Re attach to splitter plate 5 Repeat with the other shoulder strap This restraint has a shoulder height level label Use this to gauge when your child is too big for the restraint Once your child s shoulders reach the dotted line it is time to move to a bigger restraint See page 20 SHOULDERS MUST BE BELOW THIS LINE Shoulder Strap Height The shoulder straps must pass under the steel bars at the back of the restraint They must not must pass over the outside of the steel bars at the back of the restraint Canopy removal To remove the canopy press the button in the canopy mount and pull the canopy bow out Dream Drape 1 Unzip the zipper behind the front canopy bow 2 Pullthe dream drape out of the compartment 3 Attach the magnets on each corner to the corner to the front of the restraint Seat Cover Removal 1 Pull the fastening pieces underneath the edge of the seat out 2 Remove the harness from the splitter plate 3 Remove the seat cover from the adjustment button as shown 16 4 Remove the seat pad from the stroller release button as shown VERY IMPORTANT Only use this child re straint with the cover supp
6. elt placement REARWARD FACING BELT PATH REARWARD FACING BELT PATH LAP AND SASH BELTS BELT HERE Installation Base 6 CHECK a Vehicle belt is securely engaged in buckle b Vehicle lap belt or lap sash belts are correctly positioned in the lock off c Vehicle belt lock off is securely engaged d Level indicator bubble is fully in the clear area Installation Restraint TO INSTALL First make sure there is noth ing in or on the base blankets toys etc These may stop the restraint from latching in securely Lower the restraint down into the base Listen for a CLICK from the latches in the base Pull up on the restraint to en sure it is securely latched TO RELEASE Lift the restraint with one hand while pulling up on the release latch at the back of the base 25 Tether Strap Use This child restraint has a fixed A WARNING tether strap permanently at A WARNING tached to the restraint and an adjustable tether strap that can be removed and left in the vehicle Always use this tether strap Connect the tether strap to the built in anchorage fitting in the vehicle or if there is not one available install the an chor fitting supplied with this restraint by following these instructions Store the extra webbing in the bag attached to the end of the tether NOTE the tether strap wraps around the sides of the restraint not over
7. en harness by pressing on adjuster button while pulling on the harness straps 2 Press button to open the quick release buckle Spread harness straps apart 3 Place child in restraint in seated position firmly against both the back and bottom of the restraint Securing child the restraint 4 Place buckle tongues into the quick release buckle IMPORTANT The buckle tongue pushed in last should CLICK when it locks into place If it does not click try again or try cleaning the buckle See page 31 6 Tighten harness by pulling on the adjuster strap at the front of the restraint Note you may need to pull excess shoulder strap webbing through the Quick Release Buckle Tongues upward towards the child s shoulder and then pull on the adjuster strap This may need to be repeated several times to get the webbing fitting snugly 10 Securing child in the restraint child i Securing child in the restraint the restraint 7 Verify that the harness is snug around the child s waist and shoulders Shoulder Strap Height Correct positioning of the shoulder straps is essential for your baby s safety TO CHECK 1 With child placed in the restraint note where the shoulder straps enter the slots in the backrest If adjustment is needed follow the next steps TO ADJUST 2 With child removed loosen harness Turn carrier over and remove one shoulder strap harness loop from th
8. f countertops tables or other high surfaces Always stay within arms reach whenever carrier is not on floor ground Suffocation hazard Infant carrier can roll over on soft surfaces and suffocate child Never place carrier on beds sofas or other soft surfaces Strangulation hazard Child can strangle in loose restraint straps Always use harness Never leave child in carrier when straps are loose or undone Harness straps should be snug A snug strap should not allow any slack It lies in a relatively straight line without sagging It does not press on the child s flesh or push the child s body into an unnatural position Never place carrier on top of a shopping cart Carrier will not be properly secured and could fall Do not use carrier if it is damaged or broken Only use with Nuna strollers or appropriate Nuna adapters designed for use with other strollers Always check child restraint to base connection Only install child restraint in a for ward facing vehicle seat Never install in a seat that faces the rear or the side of the vehicle This is a rearward facing child restraint Do not install facing side or forwards Never install the Child Restraint in a seat with a front airbag DEATH or SERIOUS INJURY may occur Refer to your vehicle Owners Manual for airbag warnings and information Securing child in the restraint FIRST CHECK SHOULDER STRAP HEIGHT AND ADJUST IF NECESSARY See page 12 1 Loos
9. hade PLASTIC AND METAL PARTS Use only mild detergent water and a soft cloth to clean the car seat shell handle and harness straps Air dry Do not use undiluted detergent or other solvents to clean these may cause damage HARNESS BUCKLE To clean the buckle rinse using warm water DO NOT use any soaps solvents or lubricants Using anything other than water can cause c O M 31 the buckle to malfunction Air dry When the buckle is operating correctly the tongues will push in easily and the second tongue will CLICK when it latches into place If the buckle does not appear to be working correctly get it checked or replaced by contacting the retailer from where it was purchased or by contacting Babyhood HARNESS STRAPS Either spot clean or replace DO NOT IMMERSE THE HARNESS STRAPS IN WATER NEVER iron the harness straps doing so may weaken the har ness straps STORAGE Remove the child restraint from the vehicle seat if not in use for a long period of time Put the child restraint in a cool dry place and somewhere your child cannot access it 32 Babyhood 132 Compton Road Woodridge 4114 Brisbane Australia Tel 07 3208 3555 Fax 07 3208 8691 email sales babyhood com au web www babyhood com au IM 0112B
10. is visible Repairs must only be done by the manufacturer or agent Fit the harness firmly to the child A loose harness or restraint is dangerous Fit the restraint firmly to the car seat Do not alter or modify this restraint DO NOT USE A REAR FACING CHILD RESTRAINT WHERE AN AIRBAG IS FITTED IN FRONT OF THE SEATING POSITION THIS RESTRAINT MUST BE ATTACHED TO A CHILD RE STRAINT ANCHORAGE POINT IN THE CAR REFER TO CAR OWNERS HANDBOOK FOR LOCATION OF ANCHORAGE POINTS REFER TO A CHILD RESTRAINT FITTING STATION IF NO ANCHORAGE POINTS ARE IN THE MOTOR CAR DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR This Child Restraint is To be used only in a rearward facing position until the infant s shoulders reach the shoulder height marker approximately 6 months of age Continue to use this infant restraint until the child reaches this limit Infants are at risk of serious injury if they face forward too early TO BE USED WITH A LAP SASH LAP ONLY SEAT BELT IN THE BACK OF MOST CARS WITH FORWARD FACING SEATS This restraint is 700 mm long 440 mm wide and 480 mm high with the handle down Check the measurement between the front of the seat back of the rear seat and all front seats in the car in which the restraint is intended to be used to ensure the space available is sufficient Ensure that children have adequate ventilation and shade when in the vehicle Do not use seat belt extenders if the car seat belt is not
11. lied or a manu facturer authorized replacement cover with identical shoulder height markers Shoulder Pads Shoulder pads are removable and are not necessary for safety Infant Insert The infant insert can be used to provide a snug fit for smaller babies In the back of the liner is an extra foam pad intended for use with low birth weight or very small babies This should be removed when they are bigger Remove the infant insert from the child restraint once the baby is bigger 18 Carry Handle The carry handle can be adjusted to 3 positions 1 To adjust the handle position squeeze handle buttons on both sides and rotate 2 Rotate handle until it clicks into any of the 3 positions The carry handle can be used in a vehicle in any locked position The Next Restraint This restraint is suitable for a baby up to approximately 6 months of age When the baby s shoulders are level with the shoulder height marker see page 13 they should move to a bigger restraint NOTE although children from approximately the age of 6 months can move to a forward facing restraint it is preferable if they move first to a convertible style restraint which has been approved for use rearward facing up to the age of approximately 12 months Then when the child reaches that age they can change to a forward facing position The next category of restraint is forward facing and has a six p
12. oint harness and will be suitable for the child until they are approximately 4 years of age 20 Installation General Where to install the child restraint Only install child restraint in a forward facing vehicle seat Never install in a seat that faces the rear or the side of the vehicle Install in the rear seat the safest place is normally the centre This is a rearward facing child restraint Do not install facing side or forwards The base can be installed on vehicles seats fitted with either a lap belt or a lap sash belt 1 Toinstall correctly the vehicle must be on a level surface Installation Base 2 Position base on a forward facing vehicle seat Use recline adjustment to position bubble in indicator Adjust base so bubble is be tween the black patches 3 Userecline adjustment if needed to achieve correct angle for installation Recline adjustment foot snaps into position 4 If the recline adjustment foot does not give sufficient recline add a folded towel of similar Installation Base 5 Place the base on the vehicle seat and route the vehicle belt through the opening in the base labeled Belt Path and buckle the vehicle belt Both the shoulder and lap belt must be under the blue lock off Push the base into the vehicle seat firmly and pull the vehicle belts TIGHT before locking them in place Use the Belt Path labels as a guide for correct b
13. pposite For vehicles other than sedans In Australia consult your nearest child restraint fit ting station or traffic authority for vehicle inspection to find the best correct position for the placement of the anchor age point and for the correct attachment bolt length and use of spacers In New Zealand consult the agent for the vehicle Attachment Bolt Anchor dd Fitting CE Spacers Vehicle Trim Bc Vehicle fe Metal i Structure Reinforcing Cee 2 Lock Washer Nut FRONT OF VEHICLE WARNING CHILD RESTRAINTS MUST NOT ATTACHED TO UNSOUND METAL OR WOOD OR SYNTHETIC STRUC TURES WHEN DRILLING THE 9 MM HOLE DO NOT DRILL THROUGH FUEL LINES FUEL TANKS ELECTRICAL WIR ING OR RADIO SPEAKERS WEBBING STRAPS MUST BE PROTECTED FROM SHARP CORNERS AND EDGES THE ANCHOR FITTING MUST BE USED ONLY AS DE SCRIBED ABOVE IT MUST NOT BE HOOKED ONTO ANY OTHER OBJECT 29 Use with Strollers The Nuna Pipa car seat can attach to Nuna strollers using adapters Instructions are included with the adapters which are sold separately Please visit www babyhood com au for more information 30 Cleaning Maintenance SEAT COVER Wash with cold water and mild detergent Do not iron Do not bleach or dry clean Do not twist the soft goods to dry with great force It may leave the seat cover with wrinkles Hang dry the seat cover in the s
Download Pdf Manuals
Related Search