Table of Contents
Contents
1. Subject to technical changes 182. Vista Free USB port connection Mouse components D E F G H subject to change without notice Left mouse button Right mouse button Four way button wheel with LED status display Pressing the wheel to the left or the right will enable a horizontal sequence of images Button for setting the sensor scanning rate Laser sensor Mouse frequency adjustment button On off switch Battery cover 1 J Programmable buttons o0 Getting started Please connect the mouse to your computer before installing the software You will be able to use the basic functions of the mouse without installing the software In order to use the extended functions the software must be installed Installing the software i Information A corresponding dialog box which can be worded differently independently of the operating system will appear if your operating system has been set so that drivers can only be installed if this has been signed off released by Microsoft Please confirm that you nevertheless want to install the software Mouse driver You will need mouse software to use or adjust the special functions of the mouse This driver is included and installed with the software safeguard for the content of your hard drive before the installation in order to be able to access the original files in the case of potential problems after the installation Important files can be overwritten or changed during the A instal
3. compatibility with other as yet untested components programs devices may arise Driver updates and the most up to date information on this product can be found at the following Internet address Internet www medion co uk If you need further help If the suggestions in the above sections have not helped to solve your problem please contact us It will help us to help you if you can have the following information available What is your computer configuration What additional peripherals are you using What messages are appearing on the screen What software was running when the fault occurred What steps have you already taken to solve the problem If you already have a customer number please state this 16 Recycling are Device At the end of its life the appliance must not be disposed of in household rubbish Enquire about the options for environmentally friendly disposal with your retailer Batteries Do not dispose of used batteries in the household rubbish They must be deposited at a collection point for used batteries Packaging All packaging and packaging materials that are no longer required can and should be recycled Technical Data Mouse e Connection technology Wireless e Technology Laser e Sensor scanning rate 800 1600 dpi e Buttons 3 e Battery operation 2 x 1 5V AA LR6 Receiver e Transmission frequency 2 4 GHz e Operating voltage USB port e Interface USB Type A 17
4. Table of Contents Safety and Maintenance cccsccssesccssccccscescnsssesessesecees 4 What s in the Box cccsscssssccsscsccnesscessesecsesecseeecsseneseees 7 System requirements sssseesesssosecseoseoecsesssoseoseoseoscoseoseesose 7 Mouse components s essseessesssessseeosecsseeseceseeceecoseecseecsseecseees 8 Getting started Installing the software ssessssesesssseessseessseesssseesssseesssseessseesssseesessee Mouse driver ae v e ts terssscvcpusedienss Wie aN EREA OEE Install your software as follows De installation of the software Inserting batteries 00 eee Switching the mouse on Energy saving function Connecting the receiver Adjusting the frequency i Configuration of the mouse functions ae DPI TOOl o oo cece Customer service Basic AINtsis lt ccecbessssses ccgssscSasccsesstevvaslust seosedesuvdlsdesebosdsesssacusseavestees Error handling and tipsters oeii eee a Technical SUP POlt esiin aes ea a aes If you need further help Recycling ccccccssceeeceeeees Technical Data scccccssccssecccaceccceecietevecotastcaewscessccesccsextuasccsvess 2008 Medion All rights reserved Microsoft MS DOS and Windows are registered trademarks of Microsoft Corporation in the U S and other countries Pentium is a registered trademark of Intel Corporation The names of actual companies and products mentioned herein may be the trademarks of th
5. ait until the operating system has started completely gt Locate the USB connection of your computer gt Plug the receiver into a free USB connection socket on your computer gt Windows will now establish that new hardware has been connected This will start the hardware recognition process You have now installed your receiver successfully 13 Adjusting the frequency A connection will already have been set at the factory so no adjustment will be necessary However at any stage in the future if the mouse does not react an adjustment will be necessary To adjust the frequencies of the mouse and receiver gt Bring the mouse close approx 50 cm away to the receiver gt Now press the frequency adjustment button F on the base of the mouse gt The automatic setting will function immediately if a fault should arise repeat the process A new frequency combination will be selected automatically Configuration of the mouse functions You will be able to set the mouse functions to your requirements in the System Control of Windows If you have installed the Advanced Wheel Mouse Driver a corresponding entry will have been made in the directly under All programs DPI Tool With this software the sensor scanning rate of the mouse will be shown in the taskbar Pushing the button for setting the sensor scanning this will increase the scanning rate in steps i e to control items and objects on the scre
6. by any chance batteries are swallowed consult a medical doctor immediately Do not charge batteries except rechargeable batteries Do not forcibly discharge batteries Do not short circuit batteries Do not heat or dispose of in fire Do not disassemble or deform batteries Your hands and fingers may be injured or the liquid of the battery may get into your eyes or adhere to your skin If this happens rinse with a large quantity of water immediately and consult a medical doctor Do not expose batteries to strong impacts by dropping or throwing the batteries Do not reverse the positive and negative terminals to avoid short circuit Remove promptly any used battery from the device Replace the battery with a new battery of the same type Insulate the terminal parts with tape or the like when storing or at disposal of the batteries Do not throw drained batteries in with the domestic rubbish Respect the environment and dispose of them in the specific containers for separate collection If necessary turn to you local refuse authority for advice What s in the Box Please check that the following parts and accessories are in the box If an item is missing please contact your local service centre USB Wireless receiver Wireless mouse 2 x Batteries AA LR6 1 5 V Installation software on disc User manual System requirements PC AT compatible computer Pentium 1 GHz or higher Operating system Windows XP
7. eir respective owners Information in this document is subject to change without notice Safety and Maintenance Keep these instructions with your wireless mouse set at all times The proper set up use and care can help extend the life of your product In the event that you transfer ownership of this device please provide these instructions to the new owner Whenever you edit your data it is advisable to make backup copies on an external data medium disks CD We are not liable for any loss of data and consequential damages This product is designed to run on a PC AT IBM compatible computer with USB port Follow the safety instructions for the computer to which you are connecting the devices Never open up the component housings This might lead to a short circuit or even to a fire Never allow children to use electronic devices unsupervised Children may not always correctly identify potential hazards This device should only be repaired by an authorised service centre Please contact customer care if you have any technical problems Keep devices away from moisture and avoid dust heat and direct sunlight Ensure an ambient temperature that is suitable for office equipment Before cleaning the devices remove the cable connection with the computer Clean the devices and other components with a damp cloth Do not use any solvents corrosives or gaseous detergents Position and operate these devices only on a stable even and vib
8. en more precisely Also the mouse pointer speed will increase 14 Customer service Malfunctions can sometimes have very trivial causes but at times can also be of quite a complex nature and call for an in depth analysis Basic hints The regular running of the Windows programs Defrag and Scandisk can remove sources of error and increase system performance Error handling and tips Start with a careful visual check of all cable links If the LCD s are not working make sure that the power is reaching the computer and all peripherals Check that the USB ports are active and correctly configured and that there are no resource conflicts with other devices Please refer to your PC user manual on this point Have the batteries been inserted incorrectly or are they dead Check the polarity and exchange them for new ones as necessary If you are working on a metal surface use a mouse mat Position the receiver by using a different USB port in such a way that a good radio connection is ensured If the mouse does not function properly try the following gt Check that the distance is within the working range of 5 meters gt Make sure the mouse is switched on 15 Technical Support This program has been extensively and successfully tested in our test laboratory with a number of different devices It is nevertheless quite normal for the drivers to be updated from time to time This means therefore that problems of
9. ion of the software The software can be un installed from your PC as follows 1 Click on START gt SETTINGS gt SYSTEM CONTROL 2 Double click on the software entry in the Window that opens Select the program concerned e g Advanced Wheel Mouse start the de installation and follow the instructions on your screen 11 Inserting batteries Battery compartment cover Remove the battery compartment cover by pressing the button H for unlocking the battery compartment cover gt Place the batteries supplied with the mouse 2 x type AAA into the battery compartment of the mouse Pay attention that the polarity of the batteries corresponds to the and symbols gt Push the battery compartment cover on again until it clicks in Switching the mouse on gt Position the on off switch G to the ON position Position to OFF if you will not be using the mouse for a long period of time Energy saving function The mouse will switch itself off if you do not use it for a long period of time This serves to minimize the battery consumption Click on one of the mouse buttons to switch off the energy saving function and begin using the mouse again 12 Connecting the receiver wa gt USB Receiver LED D gt Pay attention to the information in the Safety and Maintenance chapter pages 4 ff gt Switch on the computer and all the peripheral devices connected monitor printer etc and w
10. lation of programs or drivers You should make a Install your software as follows The installation menu will be started automatically if you insert the CD Information The Autorun function will probably have been deactivated if the automatic Start does not function Change this setting under Windows in your Device Manager if necessary by dealing with the CD DVD ROM entry and activating the Automatic notification in the case of a change feature Continue with Point 4 if the installation starts automatically Manual installation without the Autorun function starts with Point 1 gt Click on START and select the EXECUTE entry gt Now enter the drive letter of the CD ROM followed by a colon and the program name INSTALL into the OPEN field The drive letter can vary according to the configuration gt Confirm your entry with a click on OK gt Select the installation option and follow the instructions E Menu 1 Advanced Wheel Mouse Driver 2 DPI Information Utility e 1 This selection installs the software for the extended functions 10 e 2 This program installs a symbol in which the sensor scanning rate of the mouse will be displayed in the right section of the Task Strip The dpi rate will be selected by pressing the D button e Exit Finishes the installation program gt Restart the PC after the conclusion of the installation in order to conclude the installation successfully De installat
11. ration free surface e Allow a clearance of at least 50 cm 19 7 from sources of high frequency and magnetic interference TV mobile telephone infrared devices loudspeaker cabinets etc in order to avoid malfunctions and loss of data The distance between the transmitter and the receiver should be greater than 50 cm 19 7 e These devices are not intended for use in a heavy industrial environment Contact customer care if the connections are cut or otherwise damaged if liquid has entered the device housing if a device does not operate correctly if a device is dropped or the housing damaged Declaration of Conformity Hereby Medion AG declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 0560 Working in comfort Medical studies have shown that certain physical ailments and injuries are linked to prolonged and repetitive movements in an unsuitable working environment and to unsafe working habits Take frequent breaks when using a computer If you experience pain numbness or tingling in your arms wrists hands or fingers consult a medical doctor About the Laser Battery Handling Batteries may contain combustible materials Misusing them may cause battery leakage heat explosion or ignition bringing about injury or damage to the product or you Please observe strictly the following e Keep children away from batteries e If
Download Pdf Manuals
Related Search