Industrial Data Communication Connect Series
Contents
1. Port n Disconnected module Off LED fail or module off The LEDs LNK ACT green color of fiber ports are described in the next table cable No external supply or hardware failure Green Description Causes Check if the module is completely supplied by an external power supply or check if the cable is connected Indicates the module has link 100 Mbps On Blinkin Indicates the module is 9 active and link 100 Mbps Disconnected module cable No external supply or hardware failure Off LED fail or module off Altus S A Check if the module is completely supplied by an external power supply or check if the cable is connected 20 Industrial Data Communication Connect Series Doc Code CE125000 Revision A JN4508f m Description The JN4508f m is an Industrial managed fast Ethernet switch equipped with 6 ports 10 100 Mbps ports RJ 45 plus 2 100Mbps Fiber uplink ports Combined the outstanding L2 management features along with the LLDP and high system reliability including MSR and MSTP network redundancy technologies for ensuring real time and high quality connectivity in various networking applications The JN4508f m adopted 32 Gbps switch fabric to provide real time non blocking transmission performance for satisfying the needs of high bandwidth data transmission requiring applications while ensuring traffic switching without data loss Besides the new system design includes a hardware based watchdog time2. Power input relay 6 pins removable terminal block Diagnostic LED PWR1 PWR2 Power input status redundant Alm Alarm status LNK ACT 7 8 only JN3008f m Fiber port traffic status 1 to 8 JN3008 or 1 to 6 JN3008f m ports RJ45 port traffic status DIP switch configuration DIP 1 to 5 Enable Disable port link down alarm event Notes Broadcast storm control Traffic threshold 200 packets s at 100 Mbps 20 packets s at 10 Mbps Connectors RJ45 connector 10Base T 2 pairs UTP STP category 3 category 4 category 5 cable EIA TIA_568B 100 ohm 100 m and 100 Base TX 2 pairs UTP STP category 5 cable EIA TIA 568B 100 ohm 100 m SC connector supports multi mode fiber 50 125 um or 62 5 125 um max distance 2 000 m Alarm relay and power input 6 pins removable terminal block with redundant power input with polarity auto reverse protection Fiber Optic Port Options for Long Distance Requirement To avoid interference as well as to extend the network coverage in addition to 6 fast Ethernet copper ports JN3008f m is equipped with 2 100 Mbps fiber uplink ports supporting multi mode fiber for 2 000 m distances in order to achieve stable far end transmission Altus S A 15 Industrial Data Communication Connect Series Doc Code CE125000 Revision A Reliable Power System Design In order to operate under harsh environment of industrial sites JN3008 and JN3008f m are designed with redundant wide power input with extending volt
3. and power input range They are equipped with 2 0 Gbps high performance switching engine with packet forwarding and filtering mechanism to fulfill higher performance industrial data communication requirements in field site deployments The packet forwarding feature enables the JN3008 to handle from 64 to 1522 bytes packet sizes into 2 forwarding priority queues which is compliant with IEEE 802 1p Class of Service CoS for providing best data performance Both have broadcast storm filtering and flow control functions that can ensure data traffic delivery to destination without traffic congestion The combination of enhanced network features and rugged specifications make the JN3008 JN3008f m the best entry level networking solution in industrial deployments n Alm 2 2 ae Its main features are 9 te e 8 ports 10 100 Base TX with Auto MDI MDI X only JN3008 ZOB 6 ports 10 100 Base TX plus 2 Fast Ethernet fiber ports only JN3008f m Supports Multi mode 2 Km only JN3008f m Compact size with full power redundancy Excellent data exchange performance QoS for packet forwarding precedence Broadcast storm packet filtering Port and power event alarm Dual power inputs with redundancy High isolation voltage support Aluminum case with IP31 grade protection Extended operating temperature X JN3008 JN3008f m Broadcast storm control Default enabled Connectors Ethernet ports RJ45 Fiber port only JN3008f m Duplex SC
4. and that every PC on this network can access the switch via the web browser Launch the web browser on the PC and type hitp 4508_IP_Address the default IP address is 192 168 10 1 then press Enter The login screen will appear next and type in the user name and password and click OK button The welcome page of the Web Based management interface will appear then The default user name and password is admin admin At the left column of the web management interface are the software features where ring column will list the available settings For more operating instructions please refer to the user manual of JN4508f m Altus S A 27 Industrial Data Communication Connect Series Doc Code CE125000 Physical Dimensions The dimensions of modules are showing in mm JN4508f m 9 90 Maintenance JN4508f m LED Diagnostic Indicators 2 50 24X Revision A 95 00 oO oO wv 15062301A The switches have a LEDs to indicate the status of the communication The following tables show the meaning of each state and a respective description Power Input The LEDs PWR1 and 2 green color are described in the next table Description Causes Solution Normal use Module operational no redundant power supply or LED fail At least one external power supply is off or hardware failure Check if both power supply inputs are completely supplied by an external pow
5. supply is off or module has one completely supplied by an The output is formed port link break or hardware external power supply close circuit failure or one of the switch s Check if the cable is connected configuration events was Check if one of the pre defined achived configured events was achived Normal operation or module Normal use or LED fail has no external power supply or hardware failure Ring Status R S Alarm The LED R S green and yellow colors is described in the next table Yellow Description Causes Solution Off Normal ring use Check the ring port connection Check the ring cables and connections Blinking Ring port connection Wrong ring port is connected Off On Abnormal use Ring fail occurred One of device s ring path is broken Off Blinking Ring path broke Check if the module is completely supplied by an external power supply No external supply or hardware Off Off LED fail or module off Gillie Altus S A 29 Industrial Data Communication Connect Series Doc Code CE125000 Revision A RJ45 and Fiber Ports The LEDs LNK ACT green color of RJ45 and fiber ports are described in the next table Description On Indicates the port is linked with partner sane The port is transmitting Disconnected module Check if the module is completely Off LED fail or module off cable No external supply supplied by an external power supply or hardware failure Check
6. to the LED Indicators section for descriptions of each LED indicator Settings for Alarm Relay Output Enable or disable by a DIP switch the relay output when a port link down event occurs The next table shows how the configuration works Dip Switch Pin Nr Status Description Alarm Switch ON Enable port link down alarm event at this port Pin 1 to Pin 5 Disable port link down alarm event at this port Note After adjuting the DIPswitch please reboot the the switch to activate the new settings Mechanical Assembly Mount the din rail clip screwed on the rear of JN2005 on the DIN rail Altus S A 12 Industrial Data Communication Connect Series Doc Code CE125000 Revision A Physical Dimensions JN2005 The dimensions of module are shown in mm 3 0 11X 15030901A Maintenance JN2005 LED Diagnostic Indicators The switch has LEDs to indicate the status of the communication The following tables show the meaning of each state and a respective description Power Input The LED P green color is described in the next table Green Description Causes Normal use Disconnected module No Check if the module is LED fail or module off external supply or hardware completely supplied by an failure external power supply The LED Alm red color is described in the next table Alarms Red Description Causes Solution Altus S A 13 Industrial Data Communication Connect Series D
7. to these converstaions the switch maintains a mpa of which links need which IP multicast streams VLAN Is a logical group of workstation servers and network devices that appear to be on the same LAN despite their geographical distribution A VLAN Virtual Local Area Network allows a network of computers and users to communicate in a simulated environment Used to achieve sacalability security and ease of network management Private VLAN Direct client ports in isolated community VLAN to promiscuous port in primary VLAN SNMP Is a popular protocol for network management The SNMP Simple Network Management Protocol is used for collecting information and configuring network devices SNTP Is a simplified version of NTP Network Time Protocol that is used to synchronize computer clocks on a network The SNTP Simple Network Time Protocol is generally used when full implementation of NTP is not needed SMTP Is a TCP IP protocol used in sending and receiving e mail SMTP Simple Mail Transfer Protocol is typically used when e mail is delivered from an email client to an email server or when e mail is delivered from one e mail server to another Management IP Security IP address security to prevent unauthorized access Port Security Port security to assign authorized MAC to specific port Port mirroring Online traffic monitoring on multiple selected ports Rate Control Ingress filtering for broadcast broadcast storm control multicast
8. unknown DA or all packtes Egress filtering for all packet types Fiber Optic for Long Distance Data Transmission To offer enhanced reliability stability and extended connectivity JN4508f m is designed with 2 fiber ports with superior characteristics including antielectromagnetic interference anti moisture and antivibration capabilities To meet your needs for various distance transmission the fiber ports support multi mode fiber with 2 000 m link distance High Performance The JN450f m designed with 32 bits processor running at 180 MHz combines an embedded hardware based watchdog timer to avoid system crashed by environmental factors such as intense electromagnetic interference extreme Altus S A 22 Industrial Data Communication Connect Series Doc Code CE125000 Revision A temperature variations and or any wrong instruction looping This outstanding design can ensure the system stability and reliability when it installed in hardened environment Advanced L2 Network Control Performance and Security features The JN4508f m provides various network control and security features to ensure the reliable and secure network connection To optimize the industrial network environment the switch supports tag based VLAN IGMP Snooping IEEE 802 1s multiple spanning tree IEEE 802 1w rapid spanning tree quality of service QoS link aggregation control protocol LACP rate control port mirror etc allowing users to fully handle T
9. well as all the networking features can be enabled through these management interfaces The failure notifications are later sent through e mail SNMP trap local remote system log fault event alarm relay In addition to all these management interfaces JN4508f m also supports a network management system NMS utility for achieving cost efficiency in system construction which integrates comprehensive network monitoring features for auto topology discovery device auto discovery group IP address change and firmware update Comprehensive Redundant Solutions Multiple Super Ring The JN4508f m supports new generation ring technology which includes various new technologies for different network redundancy applications and structures It allows aggregating up to 4 fast Ethernet rings With the multiple super ring technology a node can be configured to multiple rings with the failover time in as little as 5 ms and zero second of restoration time In addition users can extend the ring topology by adding hundreds of Connect Series to meet the large scale network needs without compromising the network speed The multiple super ring also allows the Connect Series to easily connect with core management switches via standard rpid spanning tree protocol or through multiple paths or nodes to increase the reliability by rapid dual homing technology By integrating multiple super ring and link aggregation control protocol _ACP the Connect Series can enhance t
10. 1301 m to another fiber ethernet device by following the figure below Wrong connection or fiber cable type will cause the fiber port not working properly ATTENTION This is a Class 1 Laser LED product Do not stare into the Laser LED beam Altus S A 6 Industrial Data Communication Connect Series Doc Code CE125000 Revision A The table below illustrates fiber transceivers specification i Wave Link Budg Distance Fiber um Connector length um dBm Km Multi Mode 50 to 62 5 125 SC 1310nm 11 2 Notes TXPrw Min Minimum Launch Power TXPwr Max Maximum Launch Power RXPwr Min Minimum Receive Sensitivity RXPwr Max Maximum Receive Sensitivity Link Budget Minimum Launch Power Maximum Receive Sensitivity To ensure your fiber converter can transmit receive data between the 2 nodes the attenuation of the optical fiber cable should be smaller than the fiber converter s link budget Settings for Alarm Relay Output The DIP Switch pins are described in the next table Dip Switch Pin Nr Status Description Alarm Switch ON Enable link loose forwarding function Pint Disable link loose forwarding function Set RJ45 in 100Mbps full duplex mode Set RJ45 in auto negotiation mode Set fiber port in half duplex mode Set fiber port in full duplex mode Set JC1301 m in pure converter mode Set JC1301 m in switch converter mode Note After adjusting the DIP swi
11. Industrial Data Communication Doc Code CE125000 pwrt 2am O Connect JETTA 3008 Product Description cones SYS Pwr 231 Rs po Di J 7 8 dal LNK ACT 9 RX Reset JetNet 4508f Connect Series Revision A PWR1 2 Aim B ee O C onnect inx altus 7 8 ACT tOEL Uonjar Connect Series provides a complete Industrial Data Communication IDC portfolio for Fast Ethernet connectivity Designed as the ideal solution for industrial applications connecting Programmable Controllers PLCs Human Machine Interfaces HMIs Frequency Inverters and supervision stations running on industrial servers or computers Connect Series delivers a selection of managed and unmanaged switches and Ethernet copper to fiber converter The easy installation procedures DIN rail mounting and a superior rugged design for harsh environment applications Connect Series supports a high temperature range that ensures reliable operation with 2 0 Gbps Additionaly its high performance switching engine and other mechanisms as packet forwarding and filtering fulfills all industrial data communication requirements Connect Series also provides network redundancy with secure and reliable data transmission performance using a ring technology that is capable of recovery from network failures in just 5 ms As an option for redundant applications to avoid interference or even to to extend the network co
12. age range as well as auto polarity reverse function to ensure the switch s capability of transmitting data under poor power sourcing High Electromagnetic Interference Immunity In industrial applications with widespread electromagnetic interference such as the automation control and high power motor operating environments the switch s electromagnetic immunity ability will affect the quality of data transfer The JN3008 compliant with the electromagnetic interference requirements for heavy industrial applications provides a high level of electromagnetic susceptibility according the IEC EN 61000 6 2 standard with distinguished electrical slow transient radio frequency electromagnetic field and electrical fast transient protections Equipped with a rugged aluminum case with IP31 grade protection and high thermal conductivity design it is capable of resisting an extended temperature range while providing reliable connectivity under harsh industrial environments Installation JN3008 and JN3008f m Electrical Installation The following diagram shows JN3008 JN3008f m electrical installation Earth Ground Screw O O O 0 0 0 Alarm Control m porti 8 pr power A AN Sey f j a i a Earth Ground D 1 There is one grounding screw on the bottom side of JN3008 JN3008f m Connect the earth ground screw of JN3008 Jn3008f m to the grounding surface to ensure safety and prevent noise 2 Insert the positive and negative w
13. ct only supports 1 A current 24 Vdc It is not recommended to apply voltage and current higher than the specifications Wiring the Relay Input DI The Digital Inout DI contacts are in the bottom side of the device as shown in next figure It accepts one external Vdc type signal input and can be configured to send alert message through Ethernet when the signal is changed Cassis should well grounding with Earth Sensor 1 High Output DC 11 30V 0 Low Output DC 0 10V Earth Ground Bottom side Digital Input Wiring simulate Diagram Note The DI accepts Vdc type signal and supports isolated input circuit with digital high level input 11 to30 Vdc and digital low level input 0 to 10 Vdc Do not apply voltage higher than the specification it may cause internal circuit damage or a wrong action of DI JN4508f m Connecting to the Network Connecting the Ethernet Ports Connected one end of an Ethernet cable into the UTP port of JN4508f m while the other end is connected to the attached networking device All UTP ports support auto MDI MDIX function The Ethernet ports will auto detect signals from connected devices in order to decide the correct link speed and duplex mode Refer to the LED Indicators section for descriptions of each LED indicator Connection the Fiber Port Connect the fiber port on your JN4508f m to another Fiber Ethernet device by following the figure below Wrong connection or fiber cable typ
14. d Fiber Twisted Pair Cable j Optic j Pair Cable PLC JC1301 JC1301 PLC Local Expansion Auto Fault Detection through Link Loss Forwarding When using traditional fiber converters users often encounter the following problem a fiber converter acting like an ordinary unmanaged 2 port switch When one of the fiber converter s ports fails e g the TX port the other one e g FX port continues to receive data via the media e g fiber confusing the device on the other end of the media by indicating that the connection is still intact But by the time the disconnection is found this error causes a great amount of loss If a port loses the connection for any reason it will activate Link Loss Forwarding to shut down the other port as a result allowing the device on the other end of the media to detect the disconnection The administrator over the network can be informed of the disconnection immediately and can react promptly to the situation greatly reducing loss caused by any link failure Altus S A 5 Industrial Data Communication Connect Series Doc Code CE125000 Revision A The Real Time Ethernet Solution EtherCAT Test JC1301 m a has passed the system test of an open real time Ethernet solution EtherCAT For communication tasks not only the defined latency cycle time is important but the jitter also has to be limited There is no jitter between two JC1301 m converters connected via fiber end whereas EtherCAT devices a
15. e power failure alarm Disable power failure alarm Note After adjuting the DIP switch please reboot the device to activate the new settings Altus S A 17 Industrial Data Communication Connect Series ey Doc Code CE125000 Revision A Mechanical Assembly Mount the din rail clip screwed on the rear of JN3008 JN3008f m on the DIN rail Physical Dimensions JN3008 and JN3008f m The dimensions of modules are shown in mm JN3008 2 0 24X lt Q wo oO oO Oo WV pas Altus S A 18 Industrial Data Communication Connect Series Doc Code CE125000 JN3008f m 9 50 117 80 7 a 108 00 99 00 e Maintenance JN3008 and JN3008f m LED Diagnostic Indicators Revision A D2 0 24X 15030502A The switches have a LEDs to indicate the status of the communication The following tables show the meaning of each state and a respective description Power Input The LEDs PWR1 and 2 green color are described in the next table Description Causes Solution Normal use Module operational no redundant power supply or LED fail At least one external power supply is off or hardware failure Check if both power supply inputs are completely supplied by an external power supply Module operational no redundant power supply or LED fail At least one external power supply is off or hardware failure Check if both power supply in
16. e will cause the fiber port not working properly Altus S A 26 Industrial Data Communication Connect Series Doc Code CE125000 Revision A ATTENTION This is a Class 1 Laser LED product Do not stare into the Laser LED Beam JN4508f m Mechanical Assembly Mount the din rail clip screwed on the rear of JN4508f m on the DIN rail JN4508f m Management JN4508f m industrial managed switch provides both in band and out band configuration methods Is possible to configure the switch via the RS232 console with the attached console cable or remotely manage the switch via network chossing Telnet SSH Web HTTPS management Preparation for Console Management e Attach the RS232 DB9 connector to the PC COM port Connect the RJ45 connector to the console port of the JN4508f m Switch e Go to Start gt Program gt Accessories gt Communication gt Hyper Terminal and give a name to the new console connection e Choose the COM name and select the correct serial settings The serial port settings of JN4508f m are 9600 bps No parity check 8 Data bits 1 stop bit e After connected Switch login request will appear Type the username and password and to login The default username is admin password is admin e Follow the user manual to configure the software features Preparation for Web Management Before to use the embedded web interface to manage switch operation verify that JN4508f m is properly installed on your network
17. er supply Module operational no redundant power supply or LED fail At least one external power supply is off or hardware failure Check if both power supply inputs are completely supplied by an external power supply LED fail or module off Altus S A Disconnected module No external supply or hardware failure Check if the module is completely supplied by an external power supply 28 Industrial Data Communication Connect Series Doc Code CE125000 Revision A System Alarm The LED SYS green color is described in the next table Description Causes Solution Normal use ready to operating Check if the module is completely supplied by an external power supply No external supply or hardware LED fail or module off failure Digital Input DI Alarm The LED DI green color is described in the next table Description Causes High level signals is External equipment set the applied and detected digital input pins Check if the module is completely supplied by an external power supply or de external equipmente is properly connected to the digital input External equipment not set the Digital input off or LED digital input or module has no fail external power supply or hardware failure Digital Output DO Alarm The LED DO red color related to the relay output is described in the next table Description Causes Solution At least one external power Check if the module is
18. has Link re Indicates the Blinking module has Activity LED fail or module Disconnected module Check if the module is completely Off off cable No external supply supplied by an external power supply or hardware failure or check if the cable is connected Altus S A 9 Industrial Data Communication Connect Series Doc Code CE125000 Revision A JN2005 Description The JN2005 is an Industrial 5 port 10 100BaseTX Ethernet switch JN2005 adopts slim industrial design to save rail space for compact systems In order to survive under harsh environment JN2005 features an industrial grade aluminum case with IP31 grade protection ability against dust and water JN2005 provides one relay output for port link down events which is enabled disabled by the DIP switch Moreover JN2005 has good immunity against unstable power source and can accept input voltage from 18 Vdc to 32 Vdc on its terminal block Its main features are 5 ports 10 100TX with auto MDI MDI X Slim sized for industrial din rail application Relay output for port alarm High isolation voltage support Aluminum case with IP31 grade protection Extended operating temperature sooz eNIer SKUU DVVO 2 JN2005 Connectors Ethernet ports RJ45 Power input 4 pins removable terminal block Diagnostic LED P Power input status Alm Alarm status P1 to P5 RJ45 port traffic status DIP switch configuration DIP 1 to 5 Enable Disable port link down alarm eve
19. hassis Connects to the earth ground e nsert positive and negative wires into V and V contacts respectively of the terminal block connector e Tighten the wire clamp screws to prevent DC wires from being loosened e Power 1 and Power 2 support power redundancy and polarity reverse protect function That means with wrong polarity the system won t work e Positive and negative power system inputs are both accepted but Power 1 and Power 2 must apply with same mode as following figures Note The recommended working voltage is 24 Vdc Remember to unplug the power terminal block before making wire connections Otherwise your screwdriver can inadvertently short your terminal connections to the grounded enclosure If the 2 power inputs are connected JN4508f m Switch will be powered from the highest connected voltage Wiring the Relay Output DO The relay output contacts are in the bottom side as shown on the figure The relay output DO is controlled by the pre defined operating rules To activate relay output function please refer to MU225600 User Manual Managed Switch for the relay output information Altus S A 25 Industrial Data Communication Connect Series Doc Code CE125000 Revision A Chassis should well grounding with Earth DO Relay carry current 1A DC 24V Earth Ground Buzzer PLC Input Power Source Bottom side Digital Output Wiring simulate Diagram Note The relay conta
20. he link availability and increase the overall link capacity Two or more fast Ethernet connections are combined in order to increase the bandwidth and to create a resilient and redundant link Rapid Super Ring Technology Rapid super ring is the second generation of ring redundancy technology The recovery time is greatly improved from 20 ms to few ms for both copper and fiber rings The ring master can be auto selected by rapid super ring engine The first ring port of the ring master is the primary path while the second ring port of the ring master is the block path Once the primary path fails the second path will be recovered within few ms Besides the restoration time is also shortened to zero in the ring master auto selection mode Seamless Ring Port Restoration Seamless restoration is a new technology which can restore a failed ring without causing any loop problem topology change and packet loss With zero second restoration time this mechanism eliminates any unstable status and guarantees the applications running non stop Rapid Dual Homing Technology Rapid dual homing is also an important feature of new generation ring technology It supports ring coupling with other vendors devices Moreover providing easy configuration and multiple redundancies the failover time is much faster and the restoration time is zero ms Uplinks can be auto detected and gathered into groups In each group uplinks are sorted into primary secondary and sta
21. hours 1 285 382 hours 818 646 hours RoHS directive Yes Regulatory approvals CE FCC UL CE FCC CE FCC CE FCC CE FCC UL CE FCC Revision A No No No No No 506 819 hours Industrial Data Communication Connect Series Doc Code CE125000 Revision A JC1301 m Description JC1301 m is a compact 1 port Fast Ethernet media converter designed to be compact which makes it the ideal model that would physically fit into a chassis with limited space eg machinery control box and duct assembly room It also supports switch forwarding mode with abnormal packet filtering and pure converter mode for extreme low latency requirement For example requirements of EtherCAT protocol for easy maintenance and time saving JC1301 m features remote Link Loss Forwarding LLF technology which provides remote link loss signal forwarding acknowledging link events occurred on each end of JC1301 m to main server To activate forwarding mode and LLF functions simply adjust DIP switch settings and reset the converter and the reconfigurations will be applied For the field site harsh environment installation such vibrating machinery or duct assembly room JC1301 m can be easily mounted directly onto DIN rail With the IP grade 31 and rigid alloy case JC1301 m can withstand a wide temperature range severe electromagnetic interference and vibration R XY 4g Its main features are Dual forwarding modes switching and pure converter High isolation voltage
22. if the cable is connected Maintenance Connect Series Altus recommends that all modules connections be checked and that all dust or any kind of dirt located at the module s enclosure be removed at least every 6 months Manuals For further technical details configuration installation and of Connect Serie the table below should be consulted This table is only a guide of some relevant documents that can be useful during the use maintenance and configuration of Connect Series products MU225600 User Manual Managed Switch English MU225000 Manual de Utiliza o Switch Gerenciavel Portuguese MU225601 User Manual Network Management System English MU225001 Manual de Utiliza o Network Management System Portuguese Altus S A 30
23. ink higher level witch Connect Series industrial switch As shown in the below figure multiring technology simply extends the network topology by linking multiple rings into a line or into multiple directions In addition to extensibility multi ring has great diversity of various ring technologies When multi ring enabled JN4508f m can connect rapid super ring rings trunk ring and a super ring together and simultaneously provide more fast Ethernet ring connectivities This provides extensibility to new technologies while keeping the great backward compatibility JN4508 Ring B Link Aggregation Control Protocol Link aggregation control protocol allows users grouping multiple Ethernet ports in parallel to increase the link bandwidth The aggregated ports can be viewed as one physical port so that the bandwidth is higher than just one single Ethernet port The member ports of the same trunk group can balance the loading and backup with each other The LACP feature is usually used when higher bandwidth is needed for the backbone network This is a cost effective way for transferring much more data If the trunk port is also assigned as a ring port it will become a trunk ring which means the bandwidth of ring path has increased with port trunk technology Now there is no recovery time when failure occurred The JN4508i m provides a simple and easy way to aggregate port bandwidth into rapid super ring Precision Time Protocol The precis
24. ion time protocol is designed to synchronize time across Ethernet networks It allows synchronization of distributed clocks to submicrosecond accuracy for devices that may have differing precision resolution and stability JN4508f m supports auto or bindery clock master and slave modes for time synchronization to achieve a high level of synchronization within an industrial motion control environment with a minimum use of network and computing resources The protocol helps for sequencing event measurements scheduling outputs synchronizing actuation time stamping coordinating event records etc Auto Topology Discovery amp Efficient Management Through LLDP and NMS JN4508f m supports topology discovery or LLDP IEEE 802 1AB Link Layer Discovery Protocol function that can help users to discover multi vendor s network devices on the same segment by NMS Network Management System which support LLDP function With LLDP function NMS can easily maintain the topology map display port ID port description system description VLAN ID etc Once a link failure happens the topology changed events are updated to the NMS to help users easily maintain the network system Besides the SNMP and LLDP protocols JN4508f m efficiently works with the NMS which in addition to the auto topology discovery also delivers multiple super ring group management group IP assignment firmware update configuration file backup restore SNMP MIB Browser compile etc Fu
25. ires into the PW1 PW1 PW2 and PW2 contacts on the terminal block connector 3 Tighten the wire clamp screws to prevent the power wires from being loosened 4 The relay outuput alarm contacts are indicated in the terminarl block connector as shown in the figure Relay output carry ability 1 A at 24 V Set the DIP switch of port alarm to ON relay outuput alarm will detect any port failures and form a short circuit The alarm relay output is Normal Open Note The recommended working voltage is 24 Vdc Connecting to the Network Connecting the Ethernet Ports Connect one end of an Ethernet cable into the UTP port of JN3008 JN3008f m while the other end is connected to the attached networking device All UTP ports support auto MDI MDIX function Refer to the LED Indicators section for descriptions of each LED indicator Connecting the Fiber Port Connect the fiber port on JN3008f m to another fiber Ethernet device by following the figure below Wrong connection or fiber cable type will cause the fiber port to work unproperly Altus S A 16 Industrial Data Communication Connect Series EE Doc Code CE125000 Revision A ATTENTION This is a Class 1 Laser LED product Do not stare into the Laser LED beam Settings for Alarm Relay Output Dip Switch Pin Nr Status Description ON Enable port link down alarm event at this port Pin 1 to Pin 8 Disable port link down alarm event at this port Enabl
26. ndbys based on their link speed The uplink with the highest speed is more likely to be active path for data transmission Link aggregation is also integrated into rapid dual homing An uplink connection can be a single link or several links aggregated as a trunk which provides better redundancy and link capacity Trunk Ring Trunk ring is a new feature in multiple super ring which merges the two technologies of rapid super ring and link aggregation It takes advantages of aggregation to enhance the link redundancy while increasing the link speed The ring Altus S A 23 Industrial Data Communication Connect Series Doc Code CE125000 Revision A will open only if all the aggregated links are broken Link aggregation can be achieved by either static trunk or LACP Not all the link sections in a trunk ring need to be the same Ring links can be either symmetric or asymmetric Some are a single path and the others are aggregated by links where the number of links in a trunk group can be different Users can enhance the link redundancy at different locations in accordance to the need The link with less speed is more likely to be used as the backup path for restoring the network to full play capacity Multi Ring The multi ring provides easier connectivity between two ring networks The simplest example is to connect two rings by a single device Depending on the number of ports and the speed the JN4508f m can connect as a 100 Mbps ring and upl
27. nt Note Connectors RJ45 connector category 3 category 4 category 5 unshielded twisted pair or shielded twisted pair cable The link distance is maximum 100 meters Terminal block for power input with auto polarity reverse Plug and Play Switch amp High Speed Transmission JN2005 requires no user setup and immediately starts operating as soon as you power it up Excellent data transmission performance is provided for applications No traffic will be delayed with the transmission rate up to 3 2 Gbps Usage Example The next example ilustrates an architecture that JN2005 can be used to provide communication between many devices in the network The figure shows a communication with PLCs HMI and SCADA system Altus S A 10 Industrial Data Communication Connect Series Doc Code CE125000 Revision A Fast Ethernet Back bone JN2005 Programmable Logic Controller Digital AC Power Meter Link Down Dry Relay Output Programmable Logic Controller 15031005C Compact Size amp Fault Relay Output The slim sized design makes it an ideal model that would physically fit in a network environment with limited space One relay output is an important feature to let you know when there is any event of port link down Just move up the DIP switch and the fault relay alarm will be operational True Reliability for the Best Support With the 1500 Vdc isolation protection and regulatory approvals JN2005 is a reliable ch
28. o avoid attacks and ensure the secure data transmission JN4508f m features DHCP client DHCP server with IP and MAC binding 802 1X access control SSH for telnet security IP access table port security private VLAN for independent network traffic handling as well as many other security features MODBUS TCP IP for Factory Automation Network Enhancement The Modbus TCP IP protocol is supported in JN4508f m for factory automation applications It enables administrator to connect to data acquisition SCADA system and read the switch s operating information using its own MODBUS TCP IP client program for monitoring and maintaining switch s status With the supported MODBUS TCP IP the JN4508f m become an element of factory automation such as the programmable logic controller PLC distributed control system DCS and allow users to monitor maintain factory equipment on the HMI Human Machine Interface system including production information and communication status Therefore user does not need to integrate multiple management platforms to monitor factory equipment with just a single JN4508f m platform users can easily achieve enhanced monitoring and maintenance of the entire factory Easy to Configure Network Managment Interface For easy of configuration and monitoring the JN4508f m offers various of management interface such as SNMP Web browser in band telnet and out band local serial console with command like interface The switch status as
29. oc Code CE125000 Revision A At least one port is On Port link down event configured and have triggered link down event Check if the cables of P1 to P5 ports is disconnected Normal operation or link Check the power supply connector is down events are connected Check if the wires are Normal use or LED fail disabled or module has properly connected in the power supply no external power supply connector Check if the external power or hardware failure supply is working properly RJ45 Port The LEDs LNK green color and ACT yellow color of RJ45 port are described in the next table Green Yelow Description Causes o on pere Binna ping ameoa mioon aooo O Blinkin Indicates the module is 9 active and Link 10 Mbps ff Disconnected module Check if the module is cable No external completely supplied by an on a Berto OMORE AN supply or hardware external power supply or check failure if the cable is connected Altus S A 14 Industrial Data Communication Connect Series Doc Code CE125000 Revision A JN3008 JN3008f m Description The JN3008 is an 8 port fast Ethernet switch to best fit in heavy industrial field applications and the JN3008f m is an 8 port fast Ethernet switch designed with 6 RJ45 fast Ethernet copper and 2 fast Ethernet fiber ports to best fit in long distance heavy industrial field applications Both switches have an enhanced design specification including wider operation temperature
30. of 2 000 m 2 pins terminal block for power input with auto polarity reverse Switch Mode and Pure Converter Mode The JC1301 m can be used in two different modes switch mode and pure converter mode The store and forward technology is implemented in switch mode It will filter out abnormal packets to maintain network efficiency and supports the data forwarding rate up to 148 810 pps packtes per second in full wire speed with packet length from 64 to 1522 bytes In the pure converter mode the JC1301 m only converts signal between copper and fiber port without any packet check and operates in the speed of minimum data forwarding latency Altus S A 4 Industrial Data Communication Connect Series Doc Code CE125000 Revision A Traditionally media converter is used for the signal conversion between electronic and optical Most of media converters are not capable of handling all kinds of packet sizes A major drawback is that they cannot support 10 100 Mbps auto negotiation and auto detection function for the cross over or straight cable The pure converter mode has the advantage of supporting extreme low transfer latency even when the packet is with a CRC error and when the packet length is below 64 bytes Some of special devices need pure converter and they need it to operate simply without any features JC1301 m can be configured between the two modes by a DIP switch For CSMA CD compliance the UTP port supports 100 Mbps full duplex when
31. oice for hazardous applications Easy Installation for Hazardous Environment Application JN2005 can be easily wall mounted and mounted directly on DIN rail The IP31 rigid aluminum flat casing and wide operation temperature range ensure reliable operation for harsh environment Installation JN2005 Electrical Installation The following diagram shows JN2005 electrical installation 1 There is one grounding screw on the bottom side of JN2005 Connect the earth ground screw of JN2005 to the grounding surface to ensure safety and prevent noise 2 Insert the positive and negative wires into the V and V contact on the terminal block connector 3 Tighten the wire clamp screws to prevent the power wires from being loosened 4 The relay outuput alarm contacts are indicated in the terminarl block connector as shown in the figure Relay output carry ability 1 A at 24 V Set the DIP switch of Port Alarm to ON relay outuput alarm will detect any port failures and form a short circuit The alarm relay output is Normal Open Altus S A 11 Industrial Data Communication Connect Series Doc Code CE125000 Revision A Note The recommended working voltage is 24 Vdc 18 to 32 Vdc Connecting to the Network Connecting the Ethernet Ports Connect one end of an Ethernet cable into the UTP port of JN2005 while the other end is connected to the attached networking device All UTP port support auto MDI MDIX function Refer
32. port 4 trap stations SNTP Rate Control Firmware update Reset button System reboot and factory default setting Connectors Ethernet ports RJ45 Fiber ports Dual SC Power inputs relay Dual 4 pins terminal blocks RS232 console RJ45 Diagnostic LED PWR1 and 2 Power input status redundant SYS System operating status R S Ring operating status DI Digital inputs status high level signals DO Digital output status relay output LNK ACT ports 1 to 8 Fast Ethernet ports 1 to 6 and Fiber ports 7 and 8 traffic and link status Notes DHCP client The DCHP Dynamic host Configuration Protocol is a TCP IP protocol service used to configure the host dinamicaly It provide the IP address subnet mask default gateway The DHCP client is the device capable to receive the TCP IP configuration from a DHCP server Supports NMS The JN4508f m supports the NMS Network Management System JetView Pro that helps to finding and link topology discovery Multiple super ring Ring redundancy technology includes Rapid Super Ring Rapid Dual Homing and Trunk Ring Rapid dual homing Multiple uplink paths to one or multiple upper swtich Trunk ring Integrate port aggregate function in ring path to get higher throughput ring architecture IGMP snooping Is the process of listening to IGMP Internet Group Management Protocol network traffic The feature allows a network switch to listen in on the IGMP conversation between hosts and routers By listeing
33. puts are completely supplied by an external power supply LED fail or module off Altus S A Disconnected module No external supply or hardware failure Check if the module is completely supplied by an external power supply 19 Industrial Data Communication Doc Code CE125000 Alarms The LED Alm red color is described in the next table Description Connect Series Revision A Solution Check if the cables of P1 to P6 or P8 ports are disconnected At least one port is configured and have triggered link down event or at least one power supply is not connected or not working properly Port link down event or power failure occurred Check the power supply connector is connected Check if the wires are properly connected in the power supply connector Check if the external power supply is working properly Normal operation or link down events are disabled or module has no external power supply or hardware failure Normal use or LED fail RJ45 Port Check if one of PWR1 or PWR2 is turned off If one of them is off then the Alm LED is fail The LEDs LNK green color and ACT yellow color of RJ45 ports are described in the next table Description Indicates the module Green Yelow on has100 Mbps link On Indicates the module has X 10 Mbps link Bo Indicates the module is Blinking active and link 100 Mbps ee Indicates the module is Plinking active and link 10 Mbps Fiber
34. r for keeping the operating system live It also provides power redundancy with wide range voltage Vdc inputs for ensuring the power continuity in the system With a ruggedized design with IP31 enclosure JN4508f m provide highly reliable and secure data transmission under severe industrial environments To build a smart cost efficient industrial Ethernet infrastructure JN4508f m is the best choice Conn ct Its main features are a 6 ports 10 100 Base TX with auto MDI MDI X 2 ports 100 Base FX uplink ports Supports multi mode 2 000 m 32Gbps non blocking transmission 8000 MAC address table Multiple super ring with recovery time lt 5 ms Rapid dual homing Multiple ring MSTP RSTP SNTP VLAN and private VLAN QinQ GVRP QoS IGMP snooping Rate control and port trunking LACP Online multi port mirroring LLDP NMS JetView Pro for auto topology and group management Supports SNMP Multiple language Web UI Serial Management Supports MODBUS TCP Client protocol Embedded hardware watchdog for system auto rescue Software configurable alarm output Dual power inputs with redundancy Wide range voltage Vdc inputs High isolation voltage support Aluminum case with IP31 grade protection Extended operating temperature JN4508f m 1000 entries for system or remote log server Ye S Yes Jet View Pro sys Ag PMs IGMP MIB Altus S A 21 Industrial Data Communication Connect Series Doc Code CE125000 Revision A SNMP trap Sup
35. rthermore users can export the topology map to diverse formats such as JPG BMP PNG and PDF for easily managing and trouble shooting the network The user friendly software allows administrators to discover devices automatically and efficiently manage the performance of the industrial network Altus S A 24 Industrial Data Communication Connect Series Doc Code CE125000 Revision A Rugged Design for Harsh Environments The JN4508f m compliant with the electromagnetic conformance requirements of industry applications provides a high level of electromagnetic susceptibility exceeding the requirements of railway EMC standard vibration as well as traffic control and heavy industrial standards with distinguished electrical slow transient radio frequency electromagnetic field electromagnetic fast transient protection Equipped with a rugged aluminum case with high thermal conductivity design it is capable of resisting a wide temperature ranges while providing reliable connectivity under harsh industrial environments Installation JN4508f m JN4508f m Electrical Installation The following diagram shows JN4508f m electrical installation any ii DO output DI Input Redundant Power Input The next figure shows how to connect the redundant power inputs 12 24AWG Wire AC DC Power Supply DC 10V 60V 2A UL Listed AC Power input AC DC Power Supply DC 10V 60V 2A UL Listed AC Power input C
36. setting JC1301 m as pure converter If setting as 100 Mbps half duplex mode the available link distance will be 60 m only In the switch mode it will not have this limitation the link distance can be reached up to 100 m In pure converter mode the JC1301 m will operate with the minimum latency of 1 6 micro second The 2 ports of JC1301 m are inter connected via MII signals therefore the internal switch MAC and packet buffer are not used Besides the packet length will not be limited and will reach up to 1 600 bytes The updated configuration will be available after resetting the device Usage Examples The next examples ilustrates diferente architectures that JC1301 m can be used to provide long distances between devices The first figure shows a PLC communicating with a SCADA system PLC SCADA Twisted Th Fiber as Twisted S Pair Cable j Optic i Pair Cable z PLC JC1301 JC1301 The next example shows the communication between two half clusters that forms a redundant PLC Each side of the redundancy can be placed far from each other using JC1301 m attending to the system disposal issues Redundant PLC Twisted Fiber Twisted Pair Cable Optic Pair Cable PLCA PLCB z Half Cluster JC1301 JC1301 Half Cluster The example of I O expansion shows that is possible to expand the architecture in long distances from the local rack distributing the I O racks according to the system needs I O Expansion Twiste
37. support Supports Auto MDI MDI X and Auto Negotiation Supports Multi mode 2 Km Auto Link Loss Forwarding LLF for fault detection Extreme low data forwarding latency Dual modes for power input Aluminum case with IP31 grade protection Supports single fiber transmission WDM Extended operating temperature LED for power and communication diagnostics LOeL Uoner ERUR DVVO ae Ya JC1301 m Connectors Ethernet port RJ45 Fiber port Duplex SC Power input 2 Pins removable terminal block Diagnostic LED PW Power Input status TP RJ45 port traffic status FX Fiber port traffic status DIP switch configuration DIP1 LLF settings enable disable DIP2 Speed settings auto negotiation or forced 100 Mbps full duplex DIP3 Fiber port settings full duplex or half duplex DIP4 Operating mode pure converter or switch mode Notes Available modes The switch mode will begin to forward the received data only after it received the frame completely The forwarding latency depends on the packet length and the packet length support 64 to 1600 bytes The pure converter operating algorithm is different from switch mode It will direct transfer Ethernet signal without any frame checking Connectors RJ45 connector supports category 3 category 4 category 5 unshielded twisted pair or shielded twisted pair cable The link distance is maximum of 100 meters SC connector supports multi mode fiber 50 125 um or 62 5 125 um max distance
38. tch please reboot the conversor to activete the new settings Mechanical Assembly Mount the din rail clip screwed on the rear of JC1301 m on the DIN rail Altus S A 7 Industrial Data Communication Connect Series Doc Code CE125000 Revision A Physical Dimensions JC1301 m The dimensions of module are shown in mm 98 20 l 88 40 30 00 O oO nN 15030903A Maintenance JC1301 m LED Diagnostic Indicators The conversor has LEDs to indicate the status of the communication The following tables show the meaning of each state and a respective description Power Input The LED PW green color is described in the next table Description Causes Normal use F l Disconnected module No Check if the module is completely oe ear MOQUE external supply or supplied by an external power hardware failure supply Altus S A 8 Industrial Data Communication Connect Series Doc Code CE125000 Revision A RJ45 Port The LED TP green color is described in the next table Green Description On Indicates the module has Link Blinkin Indicates the 3 module has Activity Check if the module is completely supplied by an external power supply or check if the cable is connected Disconnected module cable No external supply or hardware failure LED fail or module off Fiber Port The LED FX green color is described in the next table Description Indicates the module
39. ts saoo 6e 8 J 5 f rt Yes Yes Yes 2 x 24 Vdc 2 x 24Vde 2 x 24 Vde 24 Vdc 10 to 60 Vdc 10 to 60 Vdc 10 to 60 Vdc 18 to 32 Vdc 18 to 27 Vac Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes insulation 1500Vac t500Vac_ 1500Vac 1200 Vac 1500 Vac Yes Yes Yes Yes Yes Yes Yes Yes Weight HG S 555g o 290g G Standards IEEE 802 3 10Base T Yes Yes Yes Yes Yes IEEE 802 3u 100Base TX Yes Yes Yes Yes Yes IEEE 802 3u 100Base FX Yes Yes No No Yes IEEE 802 3x Flow Control and Back Pressure Yes Yes Yes Yes Yes IEEE 802 1p Class of Service CoS Yes Yes Yes No No IEEE 802 1D 2004 Rapid Spanning Tree Protocol RSTP Yes NO No nO ne IEEE 802 1AB Link Layer Discovery Protocol LLDP ves ne me me No IEEE 802 1Q VLAN and GVRP Yes No No No No IEEE 802 1QinQ and Private yas No No No No LAN IEEE 802 1s Multiple Yes No No No No Spanning Tree Protocol MSTP Altus S A 2 Industrial Data Communication Doc Code CE125000 IEEE 802 3ad Link Aggregation Protocol LACP IEEE 802 1x Port Based Network Access Protocol IEEE 1588 Precision Time Protocol PTP Modbus TCP IP ITU T G 8032 ERPS Store and forward switch technology MTBF MIL HDBK 217F GB standard Altus S A Yes Yes Yes Yes Yes No No Connect Series No System throughput 26 Mpps 1 49 Mpps 1 49 Mpps 1 49 Mpps Packet buffer 448 Kb 448Kb o MAC address table 8 000 MACs 2 000 MACs 2000MACs 661 248 hours 903 014
40. ttached to the other Ethernet end system The system meet all requirements of EtherCAT protocol Reliable Mechanical Design Industrial applications are known as harsh environments and are required to run non stop The product is designed for rugged conditions such as high or low temperature conditions impact vibration or corrosion To cope with demanding industrial environments the aluminum alloy case is rigidand conforms to IP31 housing design Installation JC1301 m Electrical Installation The following diagram shows JC1301 m electrical installation oo Accept 24AWG wire DC 4 V V JC1301 provide polarity reverse protection 1 There is one grounding screw on the bottom side of JC1301 m connect the earth ground screw of JC1301 to the grounding surface to ensure safety and prevent noise 2 Insert the positive and negative wires into the V and V contact on the terminal block connector 3 Tighten the wire clamp screws to prevent the power wires from being loosened Note The recommended working voltage is 24 Vdc 18 to 32 Vdc or 18 Vac 18 to 27 Vac Connecting to the Network Connecting the Ethernet Ports Connect one end of an Ethernet cable into the UTP port of JC1301 m while the other end is connected to the attached networking device UTP port support auto MDI MDIX function Refer to the LED Indicators section for descriptions of each LED indicator Connecting the Fiber Port Connect the fiber port on JC
41. verage it is possible use the multi mode fiber for 2 000 m Many other smart features as discovery of devices automatic network topology mapping configurable output relay for port link loss diagnostic events support of redundant power supply inputs various DHCP functions including DHCP Client and Server make Connect Series the ideal solution for industrial data communication Ordering Information JC1301 Included Items The product package contains following item e One JC1301 m converter JN2005 Included Items The product package contains following item e One JN2005 switch JN3008 Included Items The product package contains following item e One JN3008 switch with DIN rail clip JN3008f Included Items The product package contains following item e One JN3008f m switch with DIN rail clip JN4508f m Included Items The product package contains the following items Altus S A Industrial Data Communication Connect Series Doc Code CE125000 Revision A e One managed switch JN4508f m e One RS232 DB9 to RJ45 serial cable Product Code The following codes should be used to purchase the products JC1301 m_ Ethernet Fiber Converter JN2005 Industrial 5 Ports Switch JN3008 Industrial 8 Ports Switch JN3008f m Industrial 6 Ports 2 Fibers Switch JN4508f m_ Industrial Managed 6 Ports 2 Fibers Switch Product Features General Features JN4508f m JN3008f m JN3008 JN2005 JN1301 m Number of RJ45 por
Download Pdf Manuals
Related Search