User`s manual
Contents
1. Gland e One piece Twin tub washing machine One set ES Specification Water level Water quantity about L Maximum 99 Medium 79 Minimum 59 Rated washing capacity kg 12 0 Rated spinning capacity kg 7 0 Injection pressure MPa 0 02 0 22. cause damage of the machine or injure the personal safety of the user Warning sign Contents marked with that symbol are actions forbidden to perform Performing of those actions may result in damage of the machine or injure the personal safety ofthe user Please check if the power receptacle has good earthing condition before using to guarantee your safety Forbidding sign Safety precau Please insert the power cord into special receptacle with rated vol tage Be sure to use single phase three pins receptacle The earthing terminal of the receptacle must be earthed reliably If possible please adopt electric leakage protector QD tions When the machine is normally using please put the power plug at the location easily to be insert ed and extracted by hand Be sure to pull the plug off when there s power failure or the machine is being moved cleaned or when it is idle If the power cord is bad to avoid risk it is required to replace it by the technicians of our special shop or th e after sale service department Keep the pin of the power plug clean Do not put the machine at damp place like the bathroom Never wash it with water Do not place wet laundries on the control panel Do not use water hotter than 50 C In case the washing machine is installed on ground with carpet do not block the ventilation hole with carpet Ventilation hole he bottom of th Washing m
3. it completely Then turn the pulsator with hands gently Please confirm the drainage can work normally before next using 14 Trouble shooting Answer to question If there s breakdown please pull off the power plug before checking The following phenomena are not breakdowns sometimes Please confirm again before sending it to repair If there are real breakdowns please come to the special maintenance department or after sale service department of our company Do not repair it by yourself Phenomena The reason Is there power failure The machine does Is the power plug loose not act Is the pulsator twisted by foreign materials uu Is the drain hose put down The draining does Is the drain hose frozen not work Is the drain hose blocked by foreign material Are there laundries falling to the outer side of the spin tub There l a Ni Are there hair pin coins or metal items brought inside the tub There s abnormal s the machine slanting sound and violent s the gland pressed evenly vibration during Are there laundries falling to the outer side of Spinning the spin tub Are the laundries in spin tub too much There may be some waterflowing out of t is the water remained in the factory inspection the drain hose in the first use of the machine of performance 16 Packing list Name Quantity 9 User s manual One piece One piece
4. of water e lt is suggested not to use high sudsingdetergent Usage of the detergent How to use the whitener How to use the washing powder Direct dissolved in the machine 1 Fill small quantity of water 2 Add the powder Run for 30 seconds to dissolve it completely e Avoid using whitener on laun 3 Put it in the laundries Select suitable dries with color or pattern as they water level are prone to lose color Fill water to decided level Dilute the whitener with container Pour it slowly into thewashing tub The instant dissolving of the washing The whitener shall not touch powder the laundries directly 1 Prepare warm water of 30 C and a Refer to the user s manual for container 2 Add the powder while stirring to fully dissolve it The powder is more prone to pollute the laundries than the detergent Therefore please use it with proper quantity Dosage of different washing powder is different Please refer to the instruction of the washing powder for the detail dosage the usage and quantity of the whitener For powder whitener please dissolve it before using Washing sequence Wash timer Wash selector Drain selecor Spin timer If to set less than 2 min Intensity can be standard 56 not set drain switch If to set less than 1 min in you should first surpass 6 min or soft on Drain position durin order to ensure long service life p 9 please first surpass 2 min and and then
5. turn back washing then turn back 9 SPIN TIMER 1 Fill selection A 1 Set fill selection to Wash side Figure 1 anes was ios mm SPIN igu 2 Adjust water level rod to a position as needed 2 2 Fill water and add solved powder detergent until water reaches a suitable level It begin to wash to dispense detergent uniformly Page 7 Jj Figure 2 3 Putin the wash load and supplement water as necessary Figure 3 4 Select intensity Select Normal intense or Jeans water flow intensity according to wash load Figure 3 Figure 4 5 Select wash time Select wash time according to wash load Shigune 6 After completion of wash please set drain y switch at Drain position Figure 5 DRAIN SELECTORS Figure 5 Midway spinning 1 Put the laundries into the spin tub evenly and smoothly 2 Spin 1 Put the gland in properly Please put in the gland properly even if the laundries quantity is small PushGland Ob amp Proper The laundries Proper No gland are slanting 2 Close the inner and outer cover of the spin tub Outer cover of The spin tub Inner cover of 3 Spin for 1 2 minutes The spin tub 3 Run the foam removing spinning 1 Set the fill selector handle on spin side and Water inlet fill water for about 1 min Fill selector handle e In case water flows out from wash tub side due to too much inflow please turn down the water tap a bit 2 Close the
6. Twin tub Washing Machine User s manual This manual is for HWM150 0523S e Please read this manual carefully before using Retain it for future reference Haier Contents aan of the parts see eee eee ON eSafety precautions sss tte 2 e installation and adjustment gt sn 4 Preparation before washing ccc0ccc0x 6 The musts in washing Russ ah at ote erste ie tah d i e eee 7 Usage of the detergent ccc6 ns 7 e Washing sequence s e 8 e Disposal after washing RU LEM IDE IE EE 12 e Trouble Shooting Answers to question 14 e Packing list Specification ttt ttt ttt 16 M A Names of the parts Drain selector Outer cover of the spin tub Wash selector Inner cover of the spin tub Wash timer Spin timer Water filling entrance water filling translation Control panel Bypass channel Spin tub frame Spin tub Cabinet Water level adjusting lever Overflow filter Lint filter Drain hose Cabinet handle Pulsator Valve cover Wash tub Base frame Notes All illustrations in this Manual are given for reference only Your products and accessories may show differences from these illustrations due to our continuous improvement Meaning and description of the symbols Contents marked with that symbol are related to the safety of the product and the personal safety of the users Please operate in strict conformity to the contents otherwise it may
7. achin 9 Do not wash water proof laundries like the raincoat bike covers etc to avoid abnormal vibrations in spinning A at e e Do not let the machine share one recepta with other electric appliances If the power plug is damaged or the plugging into the receptacle is loose do not use the plug a more cle ny H o Safety precautions Do not stretch hands into the working machine It is dangerous even if the rotation is slow Take special care of the children Do not decompose repair or alter the machine by Do not put any hot or heavy items such as the kettle with hot water on the washing machine Do not wash laundries with volatile materials such as thinner petrol etc Handicapped or children without care shall not use the machine 9 To protect your laundries and wash ing machine please take out all ofthe coins buttons sand hairpin and other foreign materials before washing _ Keep the machine away from direct sunlight and heat source like the heater Please check if the water faucet is open and if the connection of the water inlet pipe is proper e itis suggested to use foamless washing powder Installation and adjustment Please install and adjust the machine according to the requirement of the manua
8. f the spin tub in the order of 1 3 heading for the side of the spin tub See to Figure 3 Embed the drain hose into the i FORTI groove with hands Take care not Extendtothe Figure3 to damage the drain hose in spin tub side Embed into the fastening the fixing clamp groove in turn Install the water inlet hose Select the water level e Insert the water inlet hose into the water filling entrance on the control panel To dismantle the water inlet pipe Water inlet hose just push the control handle as indicated in the ences figure and pull it out indicator ater inlet Maximi um Select water level according to the yan quantity of the laundries Medium ed Set the water level adjusting lever inimum pV to needed line Preparation before washing Preparation before washing 1 Connect the water inlet hose 2 Confirm that the washing machine is earthed reliably Then insert the power plug into the receptacle Do not connect the earth terminal to the gas pipe and tap water pipe 3 Put down the drain hose 4 Slanting or uneven ground may result in unstable working or abnormal noise Please make the machine stand horizontally The quantity of the laundries shall not be too large Stretch Check if Clear the the laundries pocket Take strips fasten has special out the coins the buttons Tie the long i
9. l It is very important to your security and correct operating the machine Install the lint filter Put the underside of the lint filter into overflow filter overflow filter MIU then push the upside into overflow filter Ia z e After installation please refer that the lint filter installed to the right station otherwise the lint filter may be fallen off when washing influencing your use Usage of the drain hose 1 The height of the drain hose shall be less than 10 cm or the drainage will not be smooth enough and cause incomplete drainage 2 Do not tramp or press the drain hose To make smooth drainage cut the front end of the hose slantingly 5 Ce e e Q ZZ 4 If extra drain hose is needed please make separate purchase The inner diameter of the extra hose shall not less than 40mm and the length shall not exceed 1 5m If the extra hose is too long cut it either at point Aor B How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose Figure 1 Extend the drain hose from the side of spin tub e Put soft items on the ground Lean the machine down gently with the front surface facing the ground Take off the drain hose from the cabinet Take the hose out of the fixing groove See to Figure 2 e Embed the drain hose into the groove Soft item along the side o
10. ng and draining or rinsing with water filling H together please first do spinning for around 1 minute dis then do draining or rinsing with water filling Otherwise the spinning will stop owing to too much water stored in the spin tub Disposal after washing After using please clean the lint and foreign materials of the lint filter and overflow filter in time Otherwise it may influence your using the machine Please first pull off the power plug from the receptacle before cleaning Cleaning the lint filter The lint filter must be used during washing It must be cleaned in time after each using 1 Press the elastic piece at upper end of lint filter to release the tab from the filter cover and pull the lint filter outward to remove it See Figure 1 Figure 1 2 Remove lint Pull the lower end of lint filter rear cover outward to disassemble it from the lint filter front cover Lint filter rear cover Remove lint completely with clear water See up Figure 2 Assemble 3 Install lint filter Lint filter frontcover Figure 2 Too much lint on the overflow filter will influence the normal usage of the machine Please clean it every two months 1 Take off the overflow filter As indicated in the figure nip the elastic fixing claw and pull it to the direction of the arrow to take it off 12 Cleaning the overflow filter Take off the corrugation pipe Water level Dismantle the upper
11. part of the adjusting lever corrugation pipe inside the overflow filter as indicated in EN Figure 1 Y K _ gt Corrugation pipe Cleaning the overflow filter Clean the lint around the filter and flush with tap water Install the overflow filter 1 Install the corrugation pipe 2 Insert the mounting plate at the bottom of the filter into the valve cover 3 Hang up the hook at the left upper side 4 Push the upper part in as Figure 2 indicated in Figure 2 Disposal of the complete unit e After washing dismount the water inlet Wipe the complete unit with soft hose cloth twisted dry Do not store water in the tub for long Wipe with neutral detergent if too dirty ee a the water immediately Do not wash it directly by water 9 Pull off the power plug and hang up the power cord Hang up the drain hose Wipe off the water drops on the surface and inside the tub with clean soft cloth Open the cover of the wash tub and the inner outer cover of the spin tub for some time about one hour then close them Trouble shooting Answers to question When the remained water is frozen Prevent the freezing be sure to discharge the water completely after using After complete draining set the DRAIN SELECTOR at OFF If itis set at DRAIN it will be rather difficult for the frozen water to melt 9 When the water is frozen Pour hot water below 50 C into the wash tub to soak
12. s running buttons of the laundries may sand hairpins close zippers etc ex and loosen the laundries before putting them in the tub c2 cause noise For the sake of discretion please put the laundries with buttons into other laundries N Check if the laundries are applicable for washing with machine Divide the laundries that are not colorfast from other laundries Put those laundries difficult to absorb water into water with hand For those laundries with heavy soil please first remove the dirt like mud or dust For the parts with heavy soil please apply detergent on them in advance which can make it easier to remove the soil For those laundries that may get lint ball and those with long fur tum it over before putting in Do not put those laundries polluted by chemicals into the washing machine directly The musts in washing e The capacity of washing and spinning ofthe machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time Laundries quantity in one washing cycle shall be lower than the rated capacity 9 The thickness size type of the cloth will influ ence the actual washing capacity Itis suit able to put in reasonable amount of laundries and the laundries can be turned round in wash ing for one time washing Do not select Maximum water level for few laundries so as to avoid splashing
13. spin tub outer cover and spin for about 1 2 min Rinsing Rinse with water filing 1 Put the laundries into the wash tub Select suitable current according to the laundries If you find water flo wing out here please 2 Adjust the water level twist the water tap to Set the water level with water level adjusting limit the water filling lever according to the laundries quantity wv Then fill suitable water continuously 3 Rinse Adjust the wash timer to 5 7 minutes to do rinsing Repeat the midway spinning and rinsing with stored water for 2 3 times Rinse with stored water 1 Put the laundries into the wash tub Select suitable current according to the laundries 2 Fill water to preset water level 3 Rinse Adjust the wash timer to 2 3 minutes to do rinsing When the laundries quantity is few please use Soft current If you use Standard current it may splash 10 1 Put the laundries into the spin tub evenly and smoothly Press the gland in the tub properly Close the inner and outer cover of the spin tub Spin Select suitable spin time according to the laundries and do spinning During spinning if there s abnormal sound it is generally owing to slanting placement of the laundries Please stop the machine and re order the laundries e In spinning it will pause the work if you open the outer cover of the spin tub Close it to resume the spinning To do spinni
Download Pdf Manuals
Related Search