Manual - Microh
Contents
1. 1 2is bright 1 grade more than 247 is 99 grade Slow fast Sound Nouse Nouse Nouse Nouse Nouse Nouse Nouse Nouse Nouse Nouse Nouse 250 sensitiv 255 ity No use sound 0 OFF active 1 255 into 31 grade 12 DMX mode 7 7 channel mode CH1 CH2 CH3 CH4 CH5 CH6 CH7 0 11 off No Function 12 23 red 24 35 yellow 36 47 green i No Function 48 59 cyan 60 71 blue 72 83 purple 84 95 white 96 107 program 2 108 119 program 3 Master Red 120 131 program 4 Dimmer 0 255 ans Green Blue 192 143 program S S dim bright 0 255 0 255 144 155 program 6 Soe 0 OFF bright dim dim O stop OFF bright bright 156 167 program 7 1 255 into99 1 255 ON grade Slow Fast 168 179 program 8 1 2 is grade 1 more 180 191 program 9 than 247 is grade 99 192 203 program 10 slow fast 204 215 program 11 216 227 program 12 228 239 auto run Sensitivity 240 255 sound active 0 OFF 1 255into No FUNCTION 31grade 13 9 KEY FEATURES 7 x 3W Tri LEDs Per Head 28 Total 3 Pin XLR Input amp Output Adjustable Tripod Stand 4 Pedal Foot Switch Operation IR Remote Optional Operation LEDQUADPAR REMOTE Digital Display 10 TECHNICAL SPECIFICATIONS MODEL LED QUADPAR TRI MKII LAMP 28 Tri LEDS Per Head 7 VOLTAGE 120VAC 60Hz 180W FUSE 120VAC 1 5A DIMENSIONS W2. MICRO PROFESSIONAL PRODUCTS www micronpro com USER MANUAL LED QUADPAR TRI IVIKI Keep this manual for future reference TABLE OF CONTENTS 1 INTRODUCTION AND UNPACKING 1 2 SAFTEY INSTRUCTIONS 1 2 3 OPERATION INSTRUCTIONS 2 4 4 MOUNTING AND INSTALLATION 5 5 DMX 512 CONTROL CONNECTIONS 6 6 PHOTOMETRIC DATA 7 7 MENU NAVIGATION 8 8 DMX CHANNELS 9 13 9 KEY FEATURES 14 10 TECHNICAL SPECIFICATIONS 14 11 MAINTENANCE AND CLEANING 15 1 INTRODUCTION AND UNPACKING Thank you for purchasing the MICROH LED QUADPAR TRI MKII wash fixture For your own safety and knowledge please read this manual before installing or operating the device This manual covers the important information on installation and applications Please install and operate the fixture according to instructions Meanwhile please keep this manual for future reference The MICROH LED QUADPAR TRI MKII pack and go LED wash par system is made of a new type of high temperature cast aluminum casing The fixture is designed and manufactured strictly following CE standards complying with international standard DMX512 protocol This fixture is applicable but not limited to large scale live performances theater studio nightclubs and discos The MICROH LED OUADPAR TRI MKII wash fixture uses 436 powerful 10mm LED s 109 per head 20 Red 52 Green 37 Blue swhich feature high brightness and stability Please carefully unpack it when you receive the fixture and ch
3. 000 255 Blue panel 2 dim bright CH9 000 255 Red panel 3 dim bright CH10 000 255 Green panel 3 dim bright CH11 000 255 Blue panel 3 dim bright CH12 000 255 Red panel 4 dim bright CH13 000 255 Green panel 4 dim bright CH14 000 255 Blue panel 4 dim bright 10 DMX mode 5 2 channel mode CH1 CH2 0 11 off 12 23 red 24 35 yellow 36 47 green 48 59 cyan 60 71 blue 72 83 purple 84 95 white No function 96 107 program 2 108 119 program 3 120 131 program 4 132 143 program 5 144 155 program 6 156 167 program 7 168 179 program 8 180 191 program 9 192 203 program 10 204 215 program 11 216 227 program 12 228 239 auto run speed O stop 1 255 into99 grade 1 2 is grade 1 more than 247 is grade 99 slow fast 240 255 sound active Sound sensitive O OFF 1 255into 31grade 11 DMX mode 6 15 channel mode CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12 CH13 CH14 CH15 0 9 Red Green Blue Red Green Blue Red Green Blue Red Green Blue RGB panel panel panel panel panel panel panel panel panel panel panel panel dimmer 1 1 1 2 2 2 3 3 3 4 4 4 0 9 mode strobe OFF 0 9 speed 10 249 OFF 0 stop 10 255 auto 10 25 1 255 Master run 5 ON into 99 dimmer Slow grade No use No use No use No use No use No use No use No use No use No use No use dim Fast
4. could cause shock and damage If your power chord is damaged in any way please purchase a new cable from your local MICROH dealer Always disconnect power when the device is not in use or before cleaning it Never pull out the plug by tugging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective It should decrease gradually Please do not project the beam onto combustible substances Fixtures cannot be installed on or near combustible substances Keep more than 50cm distance from wall for proper ventilation and air flow If your fixture is or has become damaged in any way it shall be exclusively replaced or repaired by the manufacturer to avoid any hazard CAUTION Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source as sensitive persons may suffer an epileptic shock CAUTION The electric connection must only be carried out by a qualified electrician 3 OPERATION INSTRUCTIONS Do not turn on the fixture if it has been through severe temperature differences Damage may occur to the fixture Wait until unit is at room temperature to operate The unit should be protected from any tremor or agitation during transport Do not expose the fixture in any excessive heat moisture or any environment with too much dust when installing Do not lay any power cable
5. x H 47 2 x 94 5 Max Height 9 8 120 x 240 cm Max Height 3m CASE DIMENSIONS IL x W x H 29 x 14 x 7 5 Max Height 9 8 737 x 356 x 191 mm NET WEIGHT 20 5 Ibs 9 3 kg WARRANTY 2 Year Limited Warranty 14 11 MAINTENANCE AND CLEANING The following points have to be considered during the inspection 1 All screws for installing the device or parts of the device must be tightly connected and must not be corroded 2 There must not be any deformations on the housing colour lenses fixations or installation spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage must be handled by a skilled installer or technician Any safety issues must be resolved CAUTION DISCONNECT POWER BEFORE SERVICING In order to keep the fixture in good condition and extend the life we suggest regular cleaning to the fixture 1 Clean the inside and outside lens each week to avoid the light output from darkening due to accumulation of dust dirt etc 2 Clean the fan each week 3 A detailed electrical check by approved technician every three months is advised Ensure the circuit contacts are in good condition and prevent from overheating We recommend a frequent cleaning of the device Please use
6. PINXLR For installations where the DMX cable has to run a long distance or is in an electrically noisy environment it is recommended to use a DMX terminator This helps in preventing corruption of the digital control signal by electrical noise The DMX terminator is simply an XLR plug with a 120 O resistor connected between pins 2 and 3 which is then plugged into the output XLR socket of the last fixture in the chain Please see illustrations below 1209 X PIN 3 PIN 2 6 PHOTOMETRIC DATA MICRO PROFESSIONAL PRODUCTS LED Guadpar Tri MKII Photometric Data R 1442 646 336 210 133 5 lux G 947 486 230 127 5 86 4 lux B 1250 541 272 171 108 lux W 3330 1515 795 482 333 lux I gt gt gt gt HHH s 2 L amp 1 y 9 lt 1 2 3 W L I 1 2 3 4 5 Distance Meters 0 85 13 2 55 34 4 25 Diameter Meters 7 MENU NAVIGATION SP XX AUTO dp m u T FS XX Le cm SLAu d P 3 d 001 s s r XXX fe FS XX Ga soww Ew GXXX La wm E bXXX Pr XX Le ge Pr 01 ru CL XX emm an Ge FS XX up sow Pr 02 SP XX a acun i FS X
7. X em Pr 10 SO BO D on Ger ur ME FS XX i e Pr 11 ET UP SP XX GWR GeT ur L ae T FS XX comp Pr 12 SPAN cp comm Ger ur ME FS XX Cub bows 8 DMX CHANNELS DMX mode 1 3 channel mode CH No DMX value Function CH1 000 255 Red dim bright CH2 000 255 Green dim bright CH3 000 255 Blue dim bright DMX mode 2 4 channel mode CH No DMX value Function CH1 000 255 Master dimmer dim bright CH2 000 255 Red dim bright CH3 000 255 Green dim bright CH4 000 255 Blue dim bright DMX mode 3 8 channel mode CH No DMX value Function CH1 000 255 Master dimmer dim bright CH2 000 No function 001 255 Strobe slow fast CH3 000 255 Red panel 1 amp 2 dim bright CH4 000 255 Green panel 1 amp 2 dim bright CH5 000 255 Blue panel 1 amp 2 dim bright CH6 000 255 Red panel 3 amp 4 dim bright CH7 000 255 Green panel 3 amp 4 dim bright CH8 000 255 Blue panel 3 amp 4 dim bright DMX mode 4 14 channel mode CH No DMX value Function CH1 000 255 Master dimmer dim bright CH2 000 No function 001 255 Strobe slow fast CH3 000 255 Red panel 1 dim bright CH4 000 255 Green panel 1 dim bright CH5 000 255 Blue panel 1 dim bright CH6 000 255 Red panel 2 dim bright CH7 000 255 Green panel 2 dim bright CH8
8. a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine MICROH parts from your local dealer IF YOU SHOULD EXPERIENCE ANY PROBLEMS OR ISSUES PLEASE CONTACT MICROH PROFESSIONAL PRODUCTS BY EMAIL AT info microhpro com In the event that your unit is defective in any way please contact your local dealer to obtain an RA number for service repair DISCLAIMER MICROH believes that the information contained within this user manual is accurate However Microh is not responsible for any error or addendums to this manual If you have any comments or general suggestions on how this manual can be improved please contact info microhpro com Thank you 15 JF PROFESSIONAL PRODUCTS www microhpro com
9. eck if it was damaged during the transportation And please check whether the following items are included inside the box Par Bar One 4 Pedal Foot Switch One Adjustable Tripod One Power Cord One Bag for Par Bar One Bag for Tripod Stand One Foot Switch Controller Cable One User Manual One 2 SAFTEY INSTRUCTIONS CAUTION ELECTRIC SHOCK WARNING USE EXTREME CAUTION WHEN HANDLING WIRES This device has left the factory in perfect condition In order to maintain this condition and to ensure safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual ES Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperature and is dry This device falls under protection class I therefore it is essential that the device be grounded The electrical connection must be carried out by a qualified technician The device should only be used with rate voltage and frequency Make sure that the available voltage is not higher than 120V as stated at the end of this manual Make sure the power cord is never crimped or damaged in any way as this
10. ess R G B to choose program mode and press and buttons to adjust the intensity of the light Press FLASH to turn on off flash effect pressing and buttons to adjust the flash speed DMX MODE There are seven DMX modes 2 3 4 7 8 14 or 15 Channels You must set the DMX Channel mode before you address the fixture To select your desired DMX Channel mode press the DMX mode button and then press the or buttons to scroll through the DMX Channel modes If Red LED s glow you are in DMX Mode 1 3 DMX Channels If Green LED s glow you are in DMX Mode 2 4 DMX Channels If Blue LED s glow you are in DMX Mode 3 8 DMX Channels If Red and Green LED s glow you are in DMX Mode 4 14 DMX Channels If Red and Blue LED s glow you are in DMX Mode 5 2 DMX Channels If Green and Blue LED s glow you are in DMX Mode 6 15 DMX Channels If all the LED s glow you are in DMX Mode 7 7 DMX Channels SETTING ADDRESS Press S button to set the DMX address or initialize the program then the red green lights will flash 2 3 times Please put in 3 numbers for example 1 2 3 After the red light is on please put in the first number After the first number is accessed the green light will be on then put in the second number When the blue light is on please put in the third number After all the three numbers are entered the red green amp blue lights will flash 2 3 times which indicates that the DMX addre
11. ng load limits A knowledge of the installation material being used and periodic safety inspection of all installation material and the fixture are all imperative and should only be performed by a qualified technician Improper installation can result in bodily injury and damage The MICROH LED QUADPAR SERIES can be mounted by using the pole mount on the base of the T bar Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet The MICROH LED QUADPAR SERIES has a folding bar mechanism that is easily released by gently pressing upward on the silver clip in the middle base of the bar Please see diagrams below 5 DMX 512 CONTROL CONNECTIONS This fixture complies with international USITT DMX standards and can be used with either a 3 pin or 5 pin DMX connector Plug in the provided 3 pin XLR cable to the female 3 pin XLR output of your controller and the other side to the male 3 pin XLR input of the fixture To connect the units to DMX you must daisy chain the fixtures together as referred in the diagram below Always end your DMX 512 connection with a DMX terminator DMX OUTPUT CONTROLLER FIXTURE 1 FIXTURE 3 UP TO 30 UNITS IN MASTER SLAVEMODE 355339 LU LLU UU LU VA NN ACA S NKE 3 Aa we XLR CABLE XLR CABLE XLR CABLE DMX Output DMX Input COMMON 3 Pin XLR Socket 3 Pin XLR Socket 1 Ground DMX512 OUT DMX512 IN e Soi SPINXLR Lil mm Lol S
12. oose the DMX mode 1 7 When there is no controller signal the display will flash and turn off IR REMOTE MODE You may also operate this fixture by optional IR remote sold separately LEDQUADPAR REMOTE Operating distance of 10M Notice IR remote is ready to control the product which is in any working mode AUTO MODE Press AUTO RUN to choose Auto mode Press FLASH to turn on off the flash of the Auto Run and then pressing and buttons to adjust flash speed Press SPEED to control the speed of the Auto Run and then pressing and buttons to adjust it 5 BUILT IN PROGRAM MODE Press PROG to set built in program mode Press or to program Pressing FLASH SPEED will change the strobe rate and speed of the program Press FLASH to turn on off flash and press or to adjust the flash speed Press SPEED to set the program running speed and press or to adjust it Notice Pr 01 is a static colour program There are 8 colours to choose from Press the SPEED button to enter the static colour submenu and then pressing and buttons to scroll through the static colours SLAVE MODE Press SL to display SLAVE mode The R G B lights are off when without a master light SOUND ACTIVE MODE Press SA to display sound active mode and pressing and buttons to adjust sensitivity level o e 6 o MANUAL COLOUR DIMMING MODE Pr
13. ping speed and flash speed when Pr XX is displayed press UP or DOWN button to set the program 1 12 total 12 programs When SP XX is displayed press UP or DOWN to set the jumping speed 1 99 when FS XX is displayed press UP or DOWN to set the flash speed 0 99 O is turn off flash Notice Pr 01 is static colour select program There are 8 colours to choose from Press the SET UP button to enter the static colour submenu When CL X is displayed press UP or DOWN buttons to scroll through the static colours AUTO MODE Press MODE button when AUTO is displayed the built in programs run one after another in a continuous loop When SP XX is displayed press UP or DOWN to set the colour jumping speed 0 99 O is turn off flash When FS XX is displayed press UP or DOWN button to adjust the strobe speed 0 99 O is turn off flash SOUND ACTIVE MODE Press MODE button SU XX is display and then press UP or DOWN button to set the sound level 0 31 Under this mode the SETUP button does not function MASTER SLAVE MODE To activate slave mode press MODE button SLAU is displayed Under this mode SET UP UP and DOWN do not function DMX MODE Press MODE button When d XXX is displayed press SET UP to choose the DMX address or DMX mode When d XXX is displayed press UP or DOWN to select the DMX address 1 512 When d P X is displayed press UP or DOWN button to ch
14. s for the pedal are 1 BLACK OUT is to turn off the light 2 FREEZE is to lock the current condition 3 SOUND ACTIVE is for sound active function 4 PRESET is to select the built in programs and the static colours The designed order is program1 static colour program2 program3 program4 program5 program6 program program8 program9 program10 program11 program12 auto run red green blue yellow purple cyan white Note 1 Keep pressing the PRESET foot pedal the fixture will run the program in the designed order by cycle 2 When press the FREEZE foot pedal the fixture will lock the current condition Press the FREEZE foot pedal again and the fixture will continue running the previous program you have select 3 When the fixture is in the foot pedal controller function the LED digital display will show the current running program MANUAL COLOUR DIMMING MODE Press MODE button press SETUP to choose colour and flash speed red r X X X green G X X X blue b X X X Press SETUP to choose different colour Press UP or DOWN button to set the dimming rate 0 255 When FS XX is displayed press UP or DOWN to select flash speed 0 99 0 is turn off flash 1 is the slowest 99 is the fastest BUILT IN PROGRAM MODE Press MODE button to select built in program mode Pr XX is displayed Press SETUP button choose the program the colour jum
15. s on the floor It may cause electronic shock or damage to persons or equipment Make sure to attach the safety chain and ensure the screws are properly screwed in when installing the fixture Make sure the lens is in good condition It is recommended to replace the unit if there are any damages or severe scratches Make sure the fixture is operated and installed by qualified personnel Keep the original packaging in case of defective product Any non manufacturer additions modifications or changes in any way will void all warranty Please do not attempt to open unit It is only to be serviced by an authorized technician If this occurs or is apparent the warranty will be voided The fixture s warranty will be voided if there are any malfunctions from not following the user manual or any illegal operation shock short circuit electronic shock lamp broke etc This fixture is equipped with 9 operating modes 4 Pedal Foot Switch Manual Colour Dimming Built in Program Auto Sound Active Master Slave DMX amp IR Remote Press MODE and SET UP button simultaneously to run the auto run program mode To make the display stay on continuously press the MODE and UP buttons simultaneously To make the display turn off after 20 seconds press the MODE and DOWN buttons simultaneously 4 PEDAL FOOT SWITCH MODE In any mode you will enter the foot pedal controller function when you set foot on any of the foot pedals The function
16. ss is correct and it entered the DMX MODE automatically If the address is wrong the red light will be on Auto mode will be applied when numbers 951 are pressed The yellow light will turn on press 0 to initialize auto program If the address is greater than 512 the red light will turn on indicating new address should be put in Then the system will run in the designated mode BLACK OUT MODE Press BLACK OUT to set the LED lights power on or power off by pressing this button 4 MOUNTING AND INSTALLATION Caution For added protection mount the fixtures in areas outside walking paths seating areas or in areas were the fixture might be reached by unauthorized personnel Before mounting the fixture to any surface make sure that the installation area can hold a minimum point load of 10 times the device s weight Fixture installation must always be secured with a secondary safety attachment such as an appropriate safety cable Never stand directly below the device when mounting removing or servicing the fixture Whether installing inverted on a truss or ceiling or set on a flat level surface see image below Be sure this fixture is kept at least 0 5m 1 5 ft away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails Mounting Points Overhead mounting requires extensive experience including calculating worki
Download Pdf Manuals
Related Search