oem LoCK key version II. SySTem deSCRIpTIoN
Contents
1. S 8 KEETEC OEM LOCK cEnTRALLOCKING SYSTEM USER MANUAL lt K KEETEC WARNING Carefully read following instructions and technical specifications in this manual before installation The system must be installed and used only according to this manual The system is designed for vehicles with 12V power supply It has to be connected to 12V output and to the ground Neither producer or seller of the system is responsible for damages caused by incorrect installation using or operating of this product Unprofessional operation or modification of the system can damage the system alone or the electric system of the vehicle and leads to warranty loss For proper working of the system we recommend the installation to be made by authorized service I SYSTEM DESCRIPTION OEM LOCK key version OEM LOCK is central locking system for SKODA vehicles Set OEM LOCK contains control unit set of 4 actuators two are designed to control the front door and two to control the rear doors cabling to connect the system a set of mechanical parts rod clamps bolts and mounting rails Actuators mounted in the doors ensure movement of the rod as in manual operation Actuators in the front doors contain a switch that senses the position of the lock and sends position information to the controller The control unit based on position changes in control door lock controls all other door locks SCHEMATIC OEM LOCK key version CONNECTOR CN1 12 PIN INPUTS2. 30 sec If you don t press any button light duration will be unlimited Programming will automatically end after 30 sec FUNKCIA LOCK CHECK pri RC KEY pressbuttonsGand Turn on turnoffof LOCK CHECK function lastpressed button on RC control Turning on of this function is signalized by green flash of LED diode on RC Turning off by red flash of LED diode This function is turned off by factory settings press button twice until 1 second and LOCK CHECK funcion will be activa ted last pressed button on RC control Every press of button is signalized by red flash of LED diode then LED diode flashes with green for 1x or 2x depending on which button was pressed last 8 1x green flash or button d 2x green flash SCHEMATIC OEM LOCK version with RC CONNECTOR CN1 4 PIN CONTROL UNIT 1 Brown System unlock output wire White System lock output wire Red Power supply 12V input wire Black GND of vehicle input wire CONNECTOR CN2 2 PIN CONTROL UNIT 1 Orange Directional lights output wire Fialov Trunk opening output wire CONNECTOR CN3 12 PIN CONTROL UNIT 2 Brown System unlock input wire White System lock input wire Red Power supply 12V input wire Black GND of vehicle input wire Green wire for actuator connection Blue wire for actuator connection Brown wire for actuator connection White wire for actuator connection Black wire
3. between control unit and RC is protected by floating code OEM LOCK set contains of two control units which provides propert function of system set of 4 actuators two are designed to control the front door and two to control the rear doors cabling to connect the system a set of mechanical parts rod clamps bolts and mounting rails Actuators mounted in the doors ensure movement of the rod as in manual operation Actuators in the front doors contain a switch that senses the position of the lock and sends position information to the controller The control unit based on position changes in control door lock controls all other door locks key control DESCRIPTION OF RC o vehicle lock ignition turned off 2 vehicle unlock locked vehicle 2 a turn on function LOCK CHECK b turn off function LOCK CHECK function LOCK CHECK is disabled function LOCK CHECK is enabled 2x ic until lsec LOCK CHECK function activation last pressed button on RC w LOCK CHECK function activation last pressed ae button on RC lights up the LED diode in the front on RC always RC MAX RC LINE Note Lock Check function is available only at RC MAX and RC KEY Button on RC KEY with symbol button on the others RCs with symbol l 3e for more than 1 sec LOCK CHECK FUNCTION RC MAX This function allows you to check which button was pushed last time Buttons for locking and unlocking can be
4. for actuator connection always only RC KEY always only RC MAX Note Skoda Fabia is using 5wire actuators in the rear doors Brown color may vary wires routed from the wiring before connector are used as a door contact of the rear door to connect with car alarm Control unit 2 Control unit 1 CN2 CN1 CN3 lM 1 ZA poaa D 15A red 12V a black GND x Z Sy e 5 O a usei6 O aniq O INSTALLATION AND MAINTENANCE Installation of control units Control units must be installed into interior of vehicle The most suitable place for installation is under the dashboard When installing the servo remove the upholstery from the door to which they will be mounted Install the servomotors according to manuals for specific type of ve hicles Once installed and connected to the rod or to the lock test functionality with hand movements if the operation is smooth and mechanism isn t get stuck If ev erything is allright connect actuators wires to the power wire
5. OUTPUTS CONNECTOR Brown System unlock input wire White System lock input wire Red Power supply 12V input wire Black GND of vehicle input wire Green wire for actuator connection Blue wire for actuator connection Brown wire for actuator connection White wire for actuator connection Black wire for actuator connection Note Skoda Fabia is using 5wire actuators in the rear doors Brown color may vary wires routed from the wiring before connector are used as a door contact of the rear door to connect with car alarm INA 15A Cecilia red 12V f black GND lock input white H unlock input D useib O njq O PyM TEQue TeQre o gt 0c 9 o gt o0 2 T Na TEk YV aR YZ O O BL L FL FR z Il SYSTEM DESCRIPTION OEM LOCK version with RC OEM LOCK is central locking system with remote control It is suitable for Skoda vehicles System is controlled with RC possibility to remote control of trunk opening or with original key Communication
6. checked and therefore user can check whether he locked the car or not LOCK CHECK function is optional and turned off from factory You can activate the function by holding buttons B and amp together for two seconds When activating icons for locking and unlocking will blink once When deactivating they will blink twice If the function is activated you can check the last pushed button by briefly pushing button gt After that the icon of locking or unlocking will light for aprox 0 8 sec depending on which button was pushed last time Warning When the LOCK CHECK function is activated battery life will be shorter LOW BATTERY INDICATOR ON THE REMOTE If the battery indicator will flash in blue colour when locking or unlocking vehicle the battery in remote control is weak and you have to replace it with new one TORCH FUNCTION ON RC MAX RC LINE By holding button gt for more than 1 sec high power LED in front of the remote will light LED will light as long as you hold the button or for a specitied time even if you hold the button longer only RC MAX The time how long the LED can glow is adjustable only RC MAX LED LIGHT DURATION SETTING ON RC MAX duration of LED light can be adjusted from 1 to 30 sec or without limit Push buttons O and together for 1 sec Red LED will flash for 3 sec After those 3 sec the LED wil start to flash in 1 sec intervals Press the button gt for as long as you wish the light to be switched on max
7. mming mode and the directional lights will flash 5 times press any of the button on RC within 5 seconds successful programing of RC is confirmed by flash of directional lights lt trunk opening sH 500mA output directional lights output C directional lights output arr 9 K KEETEC 1x for RC1 2x for RC2 programming will be automatically ended after 5 seconds after programing the last RC Adding or deleting programmed remote controls when programming new ones disconnect power supply and press valet switch when pressing the valet switch connect disconnect power supply 7 times within 10 seconds while for the seventh time power remains connected Release the valet switch LED diode on control unit starts flashes quickly to confirm entry into the programming mode if you want to delete old RCs when adding new ones press on programmed RC lock button factory set Flashing LED will turn on permanently for 2 seconds then starts flashing again if you want to keep old RCs when adding new ones press on programmed RC unlock button Flashing LED will turn on permanently for 5 seconds then starts flashing again programming will be automatically ended after 10 seconds PROGRAMMING TRUNK OPENING OUTPUT Output to open the luggage compartment is factory set to that after its activation has been switched on for 1 second The system allows the output can be set in three ways 1 activate the outpu
8. s from unit according to schematic If the locks on some doors require a reverse operation exchange of power supply wires between them is required blue and green wire If this actuator is control actuator switch white and brown between them too When installing wires pay attention to moving windows or doors to prevent wires from damage The location of the inlet wires pay attention to when moving a window or door da mage After connecting all the servo motors wires and checking the correctness of engagement you can test the functionality of the system In the event that control of key locking system is active in one direction only or not responding at all move the rod so that the moving part of the servo motor moves in the middle range of motion Warning If lock freezes in winter even actuator can not unlock the door There fore it must first be lock defrosted with defrost liqiuds or by placing the vehicle into heated room then to try to unlock the doors using the central locking Before the winter season pay attention to lubricate locks PROGRAMMING THE REMOTE CONTROLS Up to 10 remote controls can be programmed into system disconnect device from power supply and press valet switch when pressing the valet switch connect disconnect power supply 5 times within 7 seconds while for the fifth time power remains connected Release the valet switch LED diode on control unit starts flashes quickly to confirm entry into the progra
9. t for the set time 1 to 300 sec Once activated the output to open the trunk is switched on for set time 2 permanent turn on the output when pressing the trunk open button and by next press output will be closed 3 in idle mode the output is 12V Once activated the output of the boot opening is with no tension on it and the output for directional lights is permanently switched on Another pressing the button to activate the output to open the boot turn off output of directional lights and on output for trunk again appears 12V Programming process of each option disconnect power supply and press valet switch when pressing the valet switch connect disconnect power supply 3 times within 5 seconds while for the third time power remains connected Release the valet switch LED diode turns off for a while and then turns on to confirm entry into the programming mode procedure is the same for all options proceed as follows according to each option programming function 1 press trunk opening button once LED diode starts flashes in 1 second intervals da za ne blika v sekundov ch intervaloch LED flashes number determines how long the trunk output will be switched on after activation When the number of flashes corresponds to time how long you want to output be switched on press again the trunk open button The length of the output is now set programming function 2 press and hold trunk opening button LED diode s
10. witched off When LED diode flashes once release the button Output is now set programming function 3 press and hold trunk opening button LED diode starts flashing in intervals one flash two flash After two flashes release the button Output is set now SYSTEM RESET disconnect power supply and press valet switch when pressing the valet switch connect disconnect power supply 10 times within 13 seconds while for the tenth time power remains connected Release the valet switch directional lights flashes three times system is now reseted to the factory settings also all programmed RCs are deleted from system Note The device OEM LOCK version for remote control is working in the band 433 2 MHz Ask your dealer for Declaration of conformity for this product TECHNICAL PARAMETERS 12V 25 Power supply Working temperature from 30 C to 70 C Working frequency P LOCK 433 92 MHz
Download Pdf Manuals
Related Search