Home

Tesla™ TI3000 GPU-24-INV-1800

Contents

1. High Power Demand High power demand is defined by a requirement of greater than 50 amps Connect to aircraft ground power receptacle DC bus power should come on and aircraft voltmeter should indicate 28 5 Vdc to 23 5 Vdc 23 Vdc minimum If current demand is greater than 50 amps converter output voltage will drop below 28 0 Vdc and LED status indicator lights will illuminate indicating current is being drawn from the power cells The greater the current draw the quicker the LED status indicator will approach red Note the LED status indicator shows the status of the power cells NOTE When all LED status indicator bars illuminate both the converter and power cells are supplying 24 Vdc power output for current demands above 50 amps For long term power requirements the TI3000 GPU 24 INV 1800 can be slaved to a vehicle charging system To avoid damage to the vehicle or the inverter unit several precautions must be taken The vehicle must have a sufficient charging system 24Vdc 100 A The alternator of the slaved vehicle must be operating in it s excited state The slave vehicle engine must be operating at 1800RPM WARNING To slave to a vehicle the NATO to dc cable must be attached to the inverter The NATO connector must be attached to the vehicle The ac load must be connected to the inverter GFI outlet and the GFI reset if it has tripped The slave vehicle engine must be b
2. Products There are no mercury or cadmium containing products present in batteries manufactured by Tesla Products Form SDS 853027 Revised 05 14 15 Supersedes NEW ECO 1001584 SAFETY DATA SHEET IV FIRST AID MEASURES Sulfuric Acid Remove to fresh air immediately If breathing is difficult give oxygen Consult a physician Lead Remove from exposure gargle wash nose and lips consult physician Ingestion Sulfuric Acid Give large quantities of water do not induce vomiting or aspiration into the lungs may occur and can cause permanent injury or death consult a physician Lead Consult physician immediately Sulfuric Acid Flush with large amounts of water for at least 15 minutes remove contaminated clothing completely including shoes If symptoms persist seek medical attention Wash contaminated clothing before reuse Discard contaminated shoes Lead Wash immediately with soap and water Sulfuric Acid and Lead Flush immediately with large amounts of water for at least 15 minutes while lifting lids Seek immediate medical attention if eyes have been exposed directly to acid V FIRE FIGHTING MEASURES Flash Point N A Flammable Limits LEL 4 1 Hydrogen Gas UEL 74 2 Hydrogen Gas Extinguishing Media Carbon dioxide foam dry chemical Avoid breathing vapors Use appropriate media for surrounding fire Special Fire Fighting Procedures If batteries are on charge shut off power Use pos
3. 50 A 24 Vdc Capacity Meter Indicates the 24V battery charge state power output status Input Voltage Selector Switch Allows unit to operate within voltage range of either 100 130 Vac or 200 260 Vac Telescopic Handle Allows for easy transport of unit 10 11 12 Product Overview 2 2 3 Front Panel Overview DC Input Circuit Breaker Trips if over current fault condition occurs AC Input Connector Connects to Single Phase 100 260 Vac line voltage Inverter Display Panel Indicates input voltage and current and output power Inverter On Off Switch Enables disables Inverter Output AC Output Circuit Breaker Trips if over current fault condition occurs 60 Hz 120 Vac Power Outlet Provides output of 120 Vac 15 A when active 113000 GPU 24 INV 1800 2 Product Overview 2 4 General Specifications Electrical DC Output 3000 peak starting amps 50 amps continuous 28 5 Vdc 1425 Watts when plugged into ac power 96 amp hours 2449 watt hours with ac power 46 amp hours 1024 watt hours of rechargeable battery power without ac Recharge Rate From Full Discharge 6O minutes 25 C AC Input e Operates and charges from Single Phase 100 260 Vac 50 60 Hz e 20 Amps 120 Vac 60 Hz 2400 Watts e 10 Amps 240 Vac 60 Hz 2400 Watts 2 kW AC Inverter e 1800 watts 120 Vac 60 Hz Pure Sine Wave lt 3 THD 15 amps output Surge 2900 watts e Dual GF
4. Causes serious eye damage Wear protective gloves protective clothing eye protection face protection May damage fertility or the unborn child if ingested or Avoid breathing dust fume gas mist vapors spray inhaled Use only outdoors or in a well ventilated area May cause cancer if ingested or inhaled Causes skin irritation serious eye damage Causes damage to central nervous system blood and Contact with internal components may cause irritation or severe burns Avoid contact with internal acid kidneys through prolonged or repeated exposure Irritating to eyes respiratory system and skin May form explosive air gas mixture during charging Extremely flammable gas hydrogen Explosive fire blast or projection hazard Il HAZARDOUS INGREDIENTS IDENTIFY INFORMATION Components CAS Number Approximate by Weight Inorganic Lead Compound Lead 7439 92 1 Lead Dioxide 1309 60 0 Ti 7440 3 1 5 in Sulfuric Acid Electrolyte Sulfuric Acid Water 7664 93 9 15 20 Case Material 5 10 Polypropylene 9003 07 0 Polystyrene 9003 53 6 Styrene Acrylonitrile 9003 54 7 Acrylonitrile Butadiene Styrene 9003 56 9 Styrene Butadiene 9003 55 8 Polyvinylchloride 9002 86 2 Polycarbonate Hard Rubber Polyethylene 9002 88 4 Polyphenylene Oxide 25134 01 4 Polycarbonate Polyester Alloy Other Absorbent Glass Mat 1 2 Inorganic lead and sulfuric acid electrolyte are the primary components of every battery manufactured by Tesla
5. Power Anytime Anywhere Tesla TI3000 GPU 24 INV 1800 User Manual Built Smart Proven Tough Tesla Industries Inc 101 Centerpoint Blvd New Castle DE 19720 302 324 8910 Phone 302 324 8912 Fax www teslaind com NOTE All users must read this entire manual prior to operating the TI3000 GPU 24 INV 1800 The 113000 GPU 24 INV 1800 is a maintenance free and sealed unit No repairs are authorized Warranty will be voided if unit is tampered with in any way or if unauthorized repairs are made For technical support please contact TESLA INDUSTRIES INCORPORATED 101 CENTERPOINT BLVD CENTERPOINT INDUSTRIAL PARK NEW CASTLE DELAWARE 19720 PHONE 302 324 8910 FAX 302 324 8912 WEBSITE www teslaind com EMAIL tesla1 teslaind com CAUTION Improper use or failure to follow instructions in this user manual can result in unit damage and or injury or death by electrical shock Any attempts to open or examine the inside of the TI3000 GPU 24 INV 1800 via a tool or device borescope probe etc can result in unit failure and or injury by electrical shock This GPU is maintenance free and should not be opened or disassembled for any reason Always protect the unit from short circuit Shipping Hazards The 113000 GPU 24 INV 1800 contains sealed dry cell rechargeable batteries that do not pose a shipping hazard No part of this manual may be reproduced or transmitted in any form or by any means electronic or m
6. Repair Request Form Please complete the information below to ensure prompt and accurate service Include this form with the unit you are returning Thank you Date of return Company name amp Billing address Contact person Phone Fax Email Purchase Order Model Serial Model Serial Shipping method to Tesla Description of shipping package Description of problem Return to Tesla Industries Inc 101 Centerpoint Boulevard New Castle DE 19720 Attention Repair Department 113000 GPU 24 INV 1800 WE GET THE MILITARY STARTED Tesla Industries Inc 101 Centerpoint Blvd New Castle DE 19720 USA Tel 302 324 8910 Fax 302 324 8912 9475 Double R Blivd Suite 2 Reno NV 89521 Tel 775 622 8801 Fax 775 622 8810 www teslaind com
7. 11 Regulated 28 5 Vdc Ground Power Connecting DC Power Cable To Unit Line up the dc plug with the receptacle Push forward while rotating the T handle one full turn clockwise Ensure dc power cable plug is fully seated into the GPU s DC Battery Receptacle The unit is now ready to safely transfer power Figure 3 11 1 Attaching DC Power Cable 10 TI3000 GPU 24 INV 1800 Connecting DC Power Cable To Vehicle or Aircraft Line up the NATO plug or aviation dc plug pins and push it in DC bus power should come on and aircraft voltmeter should indicate 24 Vdc to 23 5 Vdc 23 Vdc minimum Ensure dc power cable plug is fully seated into the vehicle or aircraft s dc receptacle Figure 3 11 2 Attaching a NATO DC Power Cable Figure 3 11 3 Attaching an Aviation DC Power to vehicle Cable to aircraft Low Power Demand Low power demand is defined by a requirement of 50 amps or less Connect dc power to vehicle or aircraft ground power receptacle DC bus power should come on and vehicle or aircraft voltmeter should indicate 28 5 Vdc to 27 Vdc 26 5 Vdc minimum If vehicle or aircraft power demand is less than 50 amps converter output will remain at 28 5 Vdc only one GREEN LED status indicator bar will illuminate If vehicle or aircraft power demand exceeds 50 amps converter voltage output will decrease and two or more LED status indicator bars will illuminate TI3000 GPU 24 INV 1800 19 _3 Operating Procedures
8. 2400 peak starting amps 10 80 charged 2400 3000 peak starting amps 80 100 charged 113000 GPU 24 INV 1800 3 6 Temperature Specifications Cold Hot Soaked Temperature Exposing the unit for one 1 hour or more to the ambient temperature establishes the unit s cold hot soaked stabilization temperature If the unit s cold hot soaked temperature is outside the normal operating temperature range the unit must be stabilized prior to operation For COLD SOAKED temperature stabilization the unit must be placed in an environment with a temperature above 10 C 41 F for 3 hours or a temperature above 20 C 68 F for 2 hours For HOT SOAKED temperature stabilization the unit must be placed in an environment with a temperature below 38 C 100 F for 1 hour Ambient Percentage of Temperature Cell Capacity 40 C 104 F 110 5 100 5 Figure 3 6 1 Output power capability versus ambient temperature Hot Soaked or Cold Soaked Definition Simple terms When a material is exposed to a change in temperature its temperature will also change Some material changes temperature quickly others slowly If the ambient temperature changes and is then held constant the materials temperature will also change until its temperature stabilizes Once the material temperature has stabilized it is considered soaked Example A unit is moved from the cool shade into the hot sun That unit s temperature will incre
9. A OPTIONAL LINE CORDS FOR WORLDWIDE OPERATIONS HZ 20 50 60 50 50 60 50 60 50 50 50 60 50 50 50 50 50 50 60 TESLA PART TI25000 004 Old British Line Cord TI25000 004 Old British Line Cord TI25000 011 Australian Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord TI25000 011 Australian Line Cord TI25000 001 North American Line Cord TI25000 011 Australian Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 001 North American Line Cord TI25000 005 United Kingdom Line Cord TI25000 004 Old British Line Cord TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 004 Old British Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Co
10. Button and LED Status Indicator The Push to Test button indicates the capacity of the power cells without applying ac input power It allows the end user to check the status of the power cells This lets the operator know if there is enough power to perform another engine start or if the unit has to be connected to ac power to allow it to recharge 1 Make sure that you wait at least 2 minutes after ac power is disconnected or dc power is extracted from the unit before you press the Push to Test button This will ensure a correct reading 2 Without ac power input or dc power output simply press the Push to Test button on the faceplate and hold for approximately 2 to 3 seconds 3 Atthis time the LED bar graph should light up indicating the status of the power cells 4 The fan should also operate at this time If you do not hear the fan running stop pressing the button and check for any obstructions to the fan CAUTION CAUTION Figure 2 11 1 Push to Test UL location Figure 2 11 2 to Test outlined in blue STATUS STATUS STATUS Full Charge Half Charge No Charge Figure 2 11 2 Unit Charge Status 113000 GPU 24 INV 1800 11 2 Product Overview 2 12 Inverter Display Panel The Inverter Display Panel see figure 2 12 1 provides information about the dc input voltage and current levels as well as the amount of ac power output If the Inverter On Off Switch is switched OFF t
11. INV 1800 This custom case weighs 73 lbs and comes equipped with side handles and locking latches 7000 026 Length 40 66 1032 76 mm Width 23 66 600 96 mm Height 19 66 499 36 mm Weight 731lbs 33 11 kg 5 2 Tesla AC Line Cords These power cables come in several lengths or can be custom ordered to fit your needs Tesla specializes in outfitting cables with a variety of connectors and junction boxes Contact Tesla Customer Service to find out more about our selection of cables Regular Line Cords Line Cords For units with a fuse and old style receptacle For units with a circuit breaker and new style receptacle TI25000 001 North American Line Cord TI25000 211 North American Line Cord TI25000 002 Italian Line Cord TI25000 212 Italian Line Cord TI25000 003 Continental European Line Cord TI25000 213 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 214 Old British Line Cord TI25000 005 England UK Line Cord TI25000 215 England UK Line Cord TI25000 006 Swiss Line Cord TI25000 216 Swiss Line Cord TI25000 011 Australian Line Cord TI25000 201 Australian Line Cord TI25000 200 Israel Line Cord TI25000 203 Israel Line Cord TI25000 300 Denmark Line Cord TI25000 304 Denmark Line Cord TI25000 032 North American Commercial Line Cord To be used for TI3000 Commercial Unit only NEMA 515P Italian Continental European Old British England UK Swiss Australian Israel De
12. Operation 4 1 General Although the TI3000 GPU 24 INV 1800 has been ruggedized and made weather resistant within the scope of unit s intended use it is essential that good general care be taken to maintain unit in good operating condition and to maximize unit s operational life 4 2 After Use Unit should be protected from environmental elements and man made hazards Ideally unit should be secured in a building or shed Most importantly unit shall be fully covered if stored while exposed to environmental elements 4 3 Power Cell Recharge The TI3000 GPU 24 INV 1800 incorporates a backcharge feature that enables the unit to be recharged from the vehicle once the engine is started and the starter generator is running This feature will enable you to start multiple vehicles without reconnecting to ac power if the GPU is allowed to backcharge for approximately 30 seconds Plug the TI3000 GPU 24 INV 1800 into ac power to keep the cells charged whenever it is not in use even if it is at Full Charge The unit will not overcharge or overheat Connect AC Power Cord to Unit CAUTION Ensure 120 or 240 Vac power cord is properly connected to an approved ac power supply After approximately 5 8 seconds ensure unit s LED status indicator illuminates indicating power cell state of charge and cooling fan is operating Any time the unit s power cells are fully discharged the unit shall be recharged within 24 hours to prevent per
13. The 24 Vdc Output Connector will provide 50 amps continuous 28 5 Vdc when plugged into ac power When the Output Connector is not in use cover the receptacle with the protective cover see figure 2 9 1 This will protect the Output Connector from dust and foreign matter Closed Figure 2 9 1 24 Vdc Output Connector Protective Cover 113000 GPU 24 INV 1800 9 2 Product Overview 2 10 Input Voltage Selector Switch The Input Voltage Selector Switch allows the unit to operate safely within the expected voltage range of either 100 130 Vac or 200 260 Vac Switch outlined in blue Changing Input Voltage Selector Switch To change the input voltage from 115 Vac to 230 Vac simply follow these steps Figure 2 10 1 Input Voltage Selecto r 1 With cross tip screwdriver remove one screw and rotate the clear protective cover to one side see figure 2 10 2 2 Flip the switch to read 230V see figure 2 10 3 3 Rotate cover back into place Replace and tighten screw CAUTION The 115 Vac setting accommodates the voltage range of 100 130 Vac The 230 Vac setting accommodates the voltage range of 200 260 Vac Figure 2 10 2 Unscrew Protective Cover Figure 2 10 3 Select Voltage Do not overtighten Selector Shield screws Be sure star locks are on screws and snug the screw Overtightening will damage the Selector Shield 10 113000 GPU 24 INV 1800 Product Overview 2 2 11 Push to Test
14. United Kingdom Line Cord TI25000 011 Australian Line Cord T1I25000 005 United Kingdom Line Cord TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 005 United Kingdom Line Cord TI25000 004 Old British Line Cord TI25000 001 North American Line Cord TI25000 011 Australian Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 001 North American Line Cord TI25000 004 Old British Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord 113000 GPU 24 INV 1800 COUNTRY Romania Russia Rwanda Saudi Arabia Scotland Senegal Seychelles Sierra Leone Singapore Slovakia Somalia South Africa Spain Sri Lanka St Pierre amp Miquelon France St Kitts amp Nevis St Lucia St Vincent Sudan Surinam Svalbard Norway Swaziland Sweden Switzerland Syria Tahiti Taiwan Tanzania Thailand Togo Tonga Trinidad amp Tobago Tunisia Turkey Uganda United Arab Emir United Kingdom amp Ireland United States Uruguay Venezuela Vietnam Virgin Islands Wales Western Samoa Yemen Yugoslavia Zaire Republic of Zambia Zimbabwe 113000 GPU 24 INV 1800 VOLTS 220 220 220 220 220 220 240 230 230 220 220 220 250 220 230 115 230 240 230 240 115 220 230 220 220 220 220 110 230 220 220 1
15. ac ground post and the positive probe negative post Multimeter should to the dc positive post Multimeter read about 2 MQ should read greater than 10 MOQ 4 Move the positive probe to the fastener screw on the DC Receptacle Multim eter should read less than 1 Q Testing the DC Outlet 4 Set multimeter to Volts 2 Place the positive probe to the fas 3 Place the negative probe to the fas tener screw on the DC Receptacle tener screw on the DC Receptacle Move the negative probe to the dc Move the positive probe to the dc negative post Multimeter should positive post Multimeter should read O Volts read about 21 23 Volts 113000 GPU 24 INV 1800 17 3 Operating Procedures 3 9 Pre Operation 1 Be sure to check that all input and output cables are not damaged See Section 5 1 2 Check unit carefully for any evidence of damage See Section 3 8 3 Make sure that airflow is not obstructed from air intake and outlet See Section 2 6 4 Check that all connections are secure and free from water Figure 3 9 1 TI3000 GPU 24 INV 1800 3 10 Transporting Unit The 13000 GPU 24 INV 1800 has a telescoping handle that makes rolling the unit easy For transporting on uneven ground axle extensions should be added to the unit For use on sand balloon tires should be installed on the unit see Optional Accessories Figure 3 10 1 Releasing Telescopic Handle 48 TI3000 GPU 24 INV 1800 Operating Procedures 3 3
16. the warranty has expired you will receive a quote for necessary repairs prior to work being done Our turnaround time is 48 hours once repairs are authorized 14 Can make my own repairs to unit During the warranty period the unit can only be repaired by Tesla Industries for the warranty to remain in effect Regardless we strongly recommend allowing Tesla to repair any unit as we will analyze the complete system and re calibrate it 15 What type of maintenance does the Turbo Start require Although the systems are maintenance free please keep units plugged in while not in use This will greatly extend the life of the cells Also keep the vent areas clean and free of debris Keep units in a well ventilated area while charging Keep the unit in a protected environment when not in use maintenance facility shed etc 16 What is included with my Turbo Start Aviation customers will receive an eight 8 foot DC Aviation Cable Assembly TI2007 208 Ground vehicle customers will receive a fifteen 15 foot DC NATO Cable Assembly TI2007 315 All customers receive an ac line cord for their home country and a full two year warranty 17 Are there any HAZMAT issues or disposability problems There are none Tesla will reclaim all battery cells for disposability purposes Contact Tesla if you have questions 113000 GPU 24 INV 1800 _6 Troubleshooting amp FAQ U_U_jU 6 2 Basic Usage Operation Ques
17. 15 230 220 220 220 220 240 120 220 120 220 120 220 230 220 220 220 220 220 APPENDIX A Cont OPTIONAL LINE CORDS FOR WORLDWIDE OPERATIONS HZ 50 50 50 60 50 60 50 50 50 50 50 50 TESLATM PART TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 001 North American Line Cord TI25000 005 United Kingdom Line Cord TI25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 003 Continental European Line Cord TI25000 006 Switzerland Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old Briti
18. 2 122 0 123 8 125 6 127 4 129 2 131 0 132 8 134 6 136 4 138 2 140 0 141 8 143 6 145 4 147 2 149 0 150 8 152 6 154 4 156 2 158 0 159 8 59 0 58 0 57 0 56 0 550 54 0 53 0 52 0 51 0 50 0 49 0 48 0 47 0 46 0 45 0 44 0 43 0 42 0 41 0 40 0 90 38 0 37 0 36 0 35 0 34 0 33 0 32 0 31 0 30 0 29 0 28 0 1 0 10 0 11 0 12 0 13 0 14 0 15 0 16 0 17 0 18 0 19 0 20 0 21 0 22 0 23 0 24 0 25 0 26 0 27 0 28 0 29 0 30 0 31 0 32 0 33 0 34 0 35 0 36 0 37 0 38 0 10 4 12 2 14 0 15 8 17 6 1 0 19 4 5 0 4 0 3 0 2 0 1 0 23 0 24 8 26 6 28 4 61 0 62 0 63 0 64 0 65 0 32 0 33 8 35 6 37 4 39 2 41 0 1 0 2 0 3 0 4 0 5 0 67 0 68 0 70 0 71 0 e e x e 49 S N x N T e e x e x 38 113000 GPU 24 INV 1800 f f Output Voltage TI3000 GPU 24 INV 1800 Output Voltage Without AC Power RJ amp xl LLI za a 22 O 10 20 30 40 50 60 MINUTES 46 AMP CONSTANT CURRENT LOAD 7 8 Maximum Output Current 115000 GPU 24 INV 1800 Maximum Output Current l5 SECONDS Calculations based on actual test data at Pratt Whitney Canada on 30 March 1992 113000 GPU 24 INV 1800 section Optional Accessories 8 1 Tesla Shipping Case The optional Shipping Case is the safest way to transport the TI3000 GPU 24
19. 50 60 50 50 50 50 50 50 50 50 50 50 50 50 50 20 20 20 20 20 60 60 20 20 20 20 60 20 60 20 TESLA PART TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 003 003 Continental European Line Cord TI25000 011 Australian Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 300 Denmark Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 001 North American Line Cord TI25000 001 North American Line Cord T1I25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 003 Continental European Line
20. Cord TI25000 003 Continental European Line Cord T1I25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord TI25000 005 United Kingdom Line Cord TI25000 200 Israel Line Cord TI25000 002 Italian Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 001 North American Line Cord T1I25000 005 United Kingdom Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord COUNTRY Laos Latvia Lebanon Lesotho Liberia Liechtenstein Lithuania Luxembourg Libya Macao Madagascar Maderia Portugal Majorca Malawi Malaysia Maldives Mali Republic of Malta Martinique Mauritania Mauritius Mexico Monaco Mongolia Montseurrat Morocco Mozambique Namibia W S Africa Nepal Neth Antilles Netherlands New Caledonia New Zealand Nicaragua Niger Nigeria Norfolk Islands Australia North Ireland North Mariana Islands U S Norway Okinawa Oman Pakistan Panama Papua New Guinea Paraguay Peru Philippines Piccairn Islands U K Poland Portugal Puerto Rico VOLTS 220 220 220 240 120 220 220 220 230 220 220 220 220 230 240 230 220 240 220 220 230 127 220 220 230 220 220 220 250 220 220 220 220 230 120 220 230 240 220 115 220 100 120 240 230 110 240 220 110 115 240 220 220 120 APPENDIX A Cont OPTIONAL LINE CORDS FOR WO
21. I receptacle Power Cell Dry High Rate Discharge Rechargeable Maintenance free Physical Properties e Size 35 97 Lx 19 25 W x 15 76 H 913 8 mm x 489 0 mm x 400 4 mm e Weight 154 Ibs 69 85 kg GPU Operating Temperature e 40 C to 60 C 40 F to 140 F without ac power e 40 C 10 55 C 40 F to 131 F with ac power GPU Storage Temperature Shock e 65 C to 105 C 85 F to 221 F e 40 G per MIL STD 810G Method 516 6 Inverter Operating Temperature Vibration e 40 C to 60 C 40 F to 140 F e Exceeds MIL STD 810G transportation helicopter and CWV profiles per Method 514 6 Inverter Storage Temperature e 40 C to 70 C 40 F to 158 F Humidity e 95 aggravated profile per MIL STD 810G Method 507 5 Cell Capacity e 40 C 110 05 Temperature e 25 C 100 05 Meets or Exceeds MILSTD 810G operational and storage e 0 C 80 05 temperature ranges per Method 501 5 and Method 502 5 e 20 C 65 10 e 40 C 50 10 113000 GPU 24 INV 1800 Product Overview 2 2 5 Physical Dimensions 15 76 400 4 Figure 2 5 1 113000 GPU 24 INV 1800 physical dimensions 2 6 Airflow Ports CAUTION When the TI3000 GPU 24 INV 1800 is plugged into Single Phase 100 260 Vac 50 60 Hz ac power the internal cooling system will efficiently regulate unit temperature regardless of load At room temperature 7 F the exhaust
22. N System is over temperature Improve ventilation and cooling Reduce Load on Inverter SYSTEM SHUTDOWN Overload or system hardware A Disconnect all loads PS FAULT SHUTDOWN fault Manually reset Inverter by turning Off DC DC SHUTDOWN then On again If Unit still does not operate Please contact Tesla Customer Service at 302 324 8910 B6 A 3000 GPU 24 INV 1800 Section 7 Performance Data f 1 Purpose This section provides performance data forthe unit Continual reference to this information will enable the user to obtain maximum performance utilization and service life from the unit Although maximum performance is not always required regular referral to this section is recommended for the following reasons A To generate knowledge of unit s performance margins to enable the operator to make sound judgment when unexpected conditions or alternate operational requirements are encountered B To enable the user to readily recognize situations requiring maximum performance C To gain experience in accurately estimating the effects of variables for which data is not presented D To help the operator determine if a vehicle or an aircraft system malfunction exists by comparing actual performance with expected performance The information in this section provides data for operational planning This is helpful when planning operations under unfamiliar conditions or environmental extremes The data
23. ON The use of unapproved ac power will damage the unit Check the Input Voltage Selector Switch window outlined in blue to ensure the switch setting 115V or 230V matches the ac power source hangar wall flight line ac power prior to connecting the unit for recharging Figure 1 3 4 TI3000 GPU 24 INV 1800 Input Voltage Selector Switch Qo T3000 GPU 24 INV 1800 Safety Review _ 1 4 Important Safety Precautions Aa WARNING Severe injury or death from fire or explosion can occur if electrical sparks are produced near fuel vapors DO NOT CONNECT ac power supply WHILE FUELING AC power functions of unit shall not be operated during any fuel handling operation Power output is restricted to dc power only 1 5 Extreme Environments CAUTION The unit s charger temperature switch automatically disables the unit when the internal temperature exceeds 150 F 65 C This protects the unit from overheating and damage If the unit shuts down move the unit into a cooler environment such as shade or air conditioning when possible Perform a full function test after the unit has been allowed to cool prior to use 113000 GPU 24 INV 1800 Section 2 Product Overview 2 1 Introduction Thank you and congratulations on the purchase of your new TI3000 GPU 24 INV 1800 Ground Power Unit The TI3000 GPU 24 INV 1800 provides dc ground power for aircraft flight line maintenance and ground Support operations The unit is de
24. RLDWIDE OPERATIONS HZ 50 50 50 50 60 50 50 50 50 TESLATM PART TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 005 United Kingdom Line Cord TI25000 006 Switzerland Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 002 Italian Line Cord TI25000 004 Old British Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 003 Continental European Line Cord T1I25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord TI25000 004 Old British Line Cord TI25000 003 Continental European Line Cord T1I25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 004 Old British Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 011 Australian Line Cord TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 005
25. air will not exceed the ambient temperature by more than 5 F In more extreme temperatures greater than 90 F the exhaust air will not exceed the ambient temperature by more than 10 F Figure 2 6 1 Air intake exhaust ports and internal air circulation 113000 GPU 24 INV 1800 Product Overview 2 Operating Positions The 113000 GPU 24 INV 1800 can be operated in both the horizontal Figure 2 7 1 and vertical Figure 2 2 positions as shown Make sure that the airflow is not obstructed from air intake Figure 2 7 3 and outlet Figure 2 7 4 2 1 Horizontal Position 2 1 3 Front Inlet 2 4 Rear Outlets 113000 GPU 24 INV 1800 Product Overview 2 2 8 AC Input Circuit Breaker The AC input circuit breaker is located above the AC Input Connector When the circuit breaker has been tripped the switch will pop out In the event that the breaker trips 1 Disconnect the ac and dc connectors Unplug ac line cord on military unit 2 Wait for a minimum of 60 seconds 3 Reset breaker by pressing rocker switch 4 Reconnect ac and dc connections to the unit The unit should power up automatically If the breaker continues to trip return the unit to Tesla Industries for repair Figure 2 8 1 AC Input Circuit Breaker outlined in blue 2 9 24 Vdc Output Connector
26. ase until it stabilizes Once stabilized the unit would be considered hot soaked The unit s temperature switch automatically disables ac power functions when the internal temperature is above 150 F 65 C This protects the unit from overheating and damage If the unit shuts down move the unit into a cooler climate such as shade or air conditioning when possible Perform a full function test prior to use after the unit has been allowed to cool 113000 GPU 24 INV 1800 oo erating Procedures 3 3 Environmental WARNING If the TI3000 GPU 24 INV 1800 is exposed to significant moisture preventive measures and precautions Shall be taken to A Prevent accumulation of moisture on ac and dc connectors receptacles B Minimize moisture entering forward inlet and outlet cooling fan vent ports When not in use unit inlet and outlet vent ports shall be covered from exposure Unit shall be kept horizontal The ambient temperature may cause the unit s protective over temperature sensors to shut down the 120 240 ac functions inverter and charger until the unit cools to normal operating temperatures If the unit shuts itself down get the unit into a cooler environment such as shade or air conditioning if possible Perform a full function check once the unit is allowed to cool prior to continued use 113000 GPU 24 INV 1800 3 Operating Procedures 3 8 Normal Function Test Procedures This section in
27. cations The reason is due to the precise dc power the small portable and quiet nature of our systems and the maintenance free aspect of our GPU s We can custom tailor ground power systems to fit your individual requirements 10 Can one person transport it Turbo Start is designed to be handled by one person The 1500 is our smallest GPU system to date and weighs 36 Ibs The TILOOO weighs 57 Lbs and can be carried or wheeled on a dolly Larger units have wheels incorporated directly on the system with an extendable handle 11 Is the Turbo Start in the government purchasing system Yes Tesla Industries is an approved vendor supplier our cage code is OVWE2 Most Tesla products are class IX have a National Stock Number NSN designation and can be acquired through the DLA Defense Logistics Agency 12 How long does this unit stay charged Unit should never be allowed to discharge fully In field use it receives a dc back charge directly from a running engine When not in use unit should be plugged into ac power outlet all the time Tesla systems will retain 80 of their capacity after one year of storage 13 How do get my Turbo Start serviced Contact Tesla We can be reached at 302 324 8910 Ask for customer service You can also email us at tesla1 teslaind com Once we receive the unit at our facility we will examine it Systems that are protected under warranty will be repaired at no charge If
28. containers tightly closed when not in use If battery case is broken avoid contact with internal components Keep vent caps on and cover terminals to prevent short circuits Place cardboard between layers of stacked automotive batteries to avoid damage and short circuits Keep away from combustible materials organic chemicals reducing substances metals strong oxidizers and water Use banding or stretch wrap to secure items for shipping Storage Store batteries in cool dry well ventilated areas with impervious surfaces and adequate containment in the event of spills Batteries should also be stored under roof for protection against adverse weather conditions Separate from incompatible materials Store and handle only in areas with adequate water supply and spill control Avoid damage to containers Keep away from fire sparks and heat Keep away from metallic objects which could bridge the terminals on a battery and create a dangerous short circuit Charging There is a possible risk of electric shock from charging equipment and from strings of series connected batteries whether or not being charged Shut off power to chargers whenever not in use and before detachment of any circuit connections Batteries being charged will generate and release flammable hydrogen gas Charging space should be ventilated Keep battery vent caps in position Prohibit smoking and avoid creation of flames and sparks nearby Wear face and eye protection when near batteri
29. d titles of this manual LIST OF ABBREVIATIONS Abbreviation Definition ac AFT AWG amp or cont C F dc EFF ft FWD GPU Hr Hz kg kHz kW LED max MQ min MPU NEMA PF PFC rms THD TMDE UAV Vac Vdc Alternating Current Airflow Technology American Wire Gauge Ampere Continuous Degree Celsius Degree Fahrenheit Direct Current Efficiency Feet Forward Ground Power Unit Hour Hertz Kilograms Kilohertz Kilowatts Light Emitting Diode Maximum megaohm Minimum Micro Power Unit National Electrical Manufacturers Association ohm power factor power factor correction root mean square Total Harmonic Distortion Test Measurement amp Diagnostic Equipment Unmanned aerial vehicle Volts Alternating Current Volts Direct Current watts 113000 GPU 24 INV 1800 section 1 Safety Review 1 1 Safety Notices Safety notices appear throughout this manual to alert the user to important information regarding proper installation operation maintenance and storage of the unit These notices as illustrated below contain a key word that indicates the level of hazard and a triangular icon that indicates the specific type of hazard Indicates a condition operating procedure or practice which if not WARNING adhered to could result in serious injury or death Indicates a condition or operating procedure which if not strictl CAUTION ee adhered to could result in damage or destruction of e
30. d wall outlet AC circuit breaker has been tripped No ac power at outlet Internal failure Water or moisture has seeped in unit Internal failure Unit is overheating Cooling fans and vents are obstructed or inoperable Remedy Plug the unit in to the appropriate ac power outlet and recharge If LEDs still do not illuminate Please contact Tesla Customer Service at 302 324 8910 Do a function check with digital meter see section 3 8 Do continuity test C No continuity check cables for cuts and replace if needed Clean contacts of debris and make sure connections are tight A Do a continuity test on the ac line cord B Check if line cord is properly secured Check to make sure ac circuit breaker is placed in the ON position Please contact Tesla Customer Service at 302 324 8910 Move unit to dry warm air and allow to dry for over 48 hours Do Not Use Unit Please contact Tesla Customer Service at 302 324 8910 Move the unit to an area 10 20 less ambient temperature Clean and clear cooling vents turn on unit and inspect if air is flowing through unit If no airflow please contact Tesla Customer Service at 302 324 8910 113000 GPU 24 INV 1800 Troubleshooting amp FAQ 6 Fault Possible Cause f Circuit breaker continuously A Unit is overheating Disconnect unit from ac input and dc t
31. echanical including photocopying recording or any information storage and retrieval system without prior written permission from Tesla Industries Inc Copyright 2015 by Tesla Industries Incorporated All rights reserved 07 14 15 Form SDS 853027 Revised 05 14 15 Supersedes NEW ECO 1001584 SAFETY DATA SHEET I PRODUCT IDENTIFICATION Chemical Trade Name as used on label Chemical Family Classification Tesla Industries Inc Sealed Lead Battery Synonyms Sealed Lead Acid Battery VRLA Battery Telephone For information contact Tesla Industries Inc Manufacturer s Name Address Customer Service Dept at 302 324 8910 Tesla Industries Inc 101 Centerpoint Blvd 24 Hour Emergency Response Contact New Castle DE 19720 4180 CHEMTREC DOMESTIC 800 424 9300 CHEMTREC INT L 703 527 3877 11 GHS HAZRDS IDENTFICATION Acute Toxicity Aquatic Chronic 1 Explosive Chemical Division 1 3 Oral Dermal Inhalation Category 4 Aquatic Acute 1 Skin Corrosion Irritation Category 1A Eye Damage Category 1 Reproductive Category 1A Carcinogenicity lead compounds Category 1B Carcinogenicity acid mist Category 1A Specific Target Organ Toxicity repeated exposure Category 2 GHS LABEL HEALTH ENVIRONMENTAL PHYSICAL Hazard Statements Precautionary Statements DANGER Wash thoroughly after handling Causes severe skin burns and eye damage Do not eat drink or smoke when using this product
32. eries The system s electronics incorporate an intelligent charging system for the cells The cells are ideal for this application as they are non spillable absorbed electrolyte dry cells that are sealed maintenance free and safe for air transport 3 How is Turbo Start used in Aviation Support There are many ways a Turbo Start will benefit your operation By using it for pre flight testing you will avoid depleting the aircraft s battery You can start the aircraft s engine with the Turbo Start as well In the hangar when connected to ac power the Turbo Start will provide 28 5 Vdc for avionics testing and will also recondition and recharge the aircraft s battery Another benefit is the ability to fly with the Turbo Start aboard your aircraft You may take the Turbo Start anywhere you travel ensuring that you will always have power 4 How much power will my Turbo Start provide Depending on the system the Turbo Start will provide anywhere from 1500 to 3500 peak starting amps 25 to 400 continuous amps dc and 23 to 96 hours of rechargeable power See our website www teslaind com to determine the proper Turbo Start for your needs 5 Will a Tesla Turbo Start spool up a turbine engine Nothing will start a turbine engine faster or safer than the right Tesla Turbo Start Not only will it eliminate hot starts but it will extend the life of your starter your engine and your battery while reducing
33. es being charged For expanded detailed info download the PDF online at http www teslaind com PDF chart Tesla Safety Data Sheet pdf or go to http www teslaind com support manuals php and click on Battery Safety Data Sheet link under Battery Info heading or use the QR Code to the right Table of Contents Section 1 Safety Review 1 1 Safety Notices 1 2 Symbols 1 3 Hazards 1 4 Important Safety Precautions 1 5 Extreme Environments Section 2 Product Overview 2 1 Introduction 2 2 Indication of Terms Shall Should and May 2 3 Front Panel Overview 2 4 General Specifications 2 5 Physical Dimensions 2 6 Airflow Ports 2 Operating Positions 2 8 AC Input Circuit Breaker 2 9 24 Vdc Output Connector 2 10 Input Voltage Selector Switch 2 11 Push to Test Button and LED Status Indicator 2 12 Inverter Display Panel 2 13 60 Hz 120 Vac Power Outlet and AC Output Circuit Breaker Section 3 Operating Procedures 3 1 Operating Procedures 3 2 General 3 3 Operating Limits and Restrictions 3 4 Performance 3 5 Engine Starting Power 3 6 Temperature Specifications 3 Environmental 3 8 Normal Function Test Procedures 3 9 Pre Operation 3 10 Transporting Unit 3 11 Regulated 28 5 Vdc Ground Power 3 12 Regulated AC Power 3 13 Charging Unit 3 14 Activating the Pure Sine Wave Inverter 3 15 Operating the Pure Sine Wave Inverte
34. for correct operations of this unit Knowledge of the operating limits restrictions performance unit capabilities and functions aids in correct and safe operations Compliance with the instructions in this manual affect operational safety as well as the warranty of the unit 3 3 Operating Limits and Restrictions The minimum maximum and normal operating ranges result from careful engineering and evaluation of test data These limitations must be adhered to during all phases of operation 3 4 Performance Refer to Section 7 PERFORMANCE DATA to determine the capability of the unit Consideration must be given to changes in performance resulting from variations in ambient temperature mode of operation state of charge with or without ac power and aircraft dc bus system inefficiency voltage drops 3 5 Engine Starting Power The unitshould always be charged above 80 prior to ground support engine starting However circumstances may exist during use where unit recharge is not readily available and immediate external engine starting power is required The following provides minimum states of charge necessary to provide ample power for an efficient engine start under specific current load demands ENGINE START PEAK CURRENT Requirements MINIMUM CHARGE Under 1200 peak starting amps 0 40 charged 1200 1500 peak starting amps 40 50 charged 1500 1800 peak starting amps 50 60 charged 1800 2100 peak starting amps 60 70 charged 2100
35. formance degradation and ensure maximum life Figure 4 3 1 Connecting 113000 GPU 24 INV 1800 10 Figure 4 3 2 AC North American Line Cord AC Power Supply 113000 GPU 24 INV 1800 Post Operations 4 CAUTION The TI3000 GPU 24 INV 1800 s power cells may be damaged if recharged by NiCad or Lithium lon battery chargers Power cells should only be charged by either the TI3000 GPU 24 INV 1800 s internal charger and the ac power cord furnished with the equipment or when connected to vehicle or aircraft s external dc power receptacle TI3000 GPU 24 INV 1800 Inverter cannot be plugged into itself to charge it s own batteries Figure 4 3 3 Proper and Improper Charging Methods 113000 GPU 24 INV 1800 27 Section 5 Unit Care and Maintenance WARNING CAUTION 5 1 Unit Care Avoid Prolonged Exposure to Extremely Damp Environments If the unit has come into contact with water disconnect ac power from the ac source If the AC Input Circuit Breaker has tripped due to water infiltration allow the unit to dry out before attempting to reset circuit breaker Cover the unit to prevent water seepage If the unit is operated in extremely damp conditions it should be stored in an environmentally controlled building when not in use Wipe unit clean periodically with a soft cloth to remove dust dirt etc Protect Cables from Damage Do not cut crush or drag the input or output power cables when handling the unit Alway
36. he Inverter Display Panel LCD will turn off indicating that the inverter is OFF Figure 2 12 1 Inverter Display Panel 2 13 60 Hz 120 Vac Power Outlet and AC Output Circuit Breaker When the Inverter is active and the AC Output Circuit Breaker is switched to the ON position the Power Outlet will provide 120 Vac at 15 amps continuous and up to 20 amps peak see figure 2 13 1 If the load exceeds 20 amps the Inverter Output Circuit Breaker will trip The outlet makes it convenient to plug in laptops test instruments cell phone chargers and other electronic devices without using an alternate power source see figure 2 13 2 Figure 2 13 1 60 2 120 Vac Output and Figure 2 13 2 60Hz 120 Vac Output AC Output Circuit Breaker outlined in blue 420 T3000 GPU 24 INV 1800 section 3 Operating Procedures 3 1 Operating Procedures This section covers normal procedures and steps necessary to ensure safe and efficient operation of the unit When not in use the unit should always remain plugged into a suitable ac power source to ensure operational readiness at all times If current demand exceeds 50 amps converter output voltage will drop below 28 5 Vdc and two or more LED status indicator bars will illuminate If all LED status indicator bars illuminate both the converter and power cells are supplying 24 Vdc power output 3 2 General The user should be well versed in both pre use and functional checks
37. ill activate the 60 Hz 120 Vac Power Outlet When the Pure Sine Wave Inverter is fully activated the Inverter display screen will be lit as well as the LED Indicators located to the left of the DC Input Circuit Breaker and the AC Output Circuit Breaker See figure 3 14 2 AC DC Input Inverter Control switch AC Output Circuit Breaker Switch To i za Figure 3 14 1 TI3000 GPU 24 INV 1800 Figure 3 14 2 TI3000 GPU 24 INV 1800 with DC Input circuit breaker in on position Inverter Activated outlined in blue 3 15 Operating the Pure Sine Wave Inverter Once the standard display screen is shown any type of 120 Vac load can be attached to the GOHz 120 Volt AC Outlet including cell phone chargers lap tops and any other electronic devices When equipment is plugged in the output power is displayed in watts on an analog bar graph at the bottom of the LCD display 3 16 Inverter Fan When the Inverter is initially powered on it is normal for the fan to be off Once an ac load is applied to the Inverter the fan will turn on The fan will continue to run until the ac load is disconnected Once the ac load is disconnected the fan will decrease in RPM and may eventually turn off to conserve power Figure 3 15 1 Inverter Display Panel Figure 3 16 1 Inverter Fan with Switch set to ON position 22 T3000 GPU 24 INV 1800 Operating Procedures 3 3 17 Inverter Output Circuit Breaker The AC Output Ci
38. itive pressure self contained breathing apparatus Water applied to electrolyte generates heat and causes it to spatter Wear acid resistant clothing gloves face and eye protection Note that strings of series connected batteries may still pose risk of electric shock even when charging equipment is shut down Unusual Fire and Explosion Hazards Highly flammable hydrogen gas is generated during charging and operation of batteries To avoid risk of fire or explosion keep sparks or other sources of ignition away from batteries Do not allow metallic materials to simultaneously contact negative and positive terminals of cells and batteries Follow manufacturer s instructions for installation and service VI PRECAUTIONS FOR SAFE HANDLING AND USE Spill or Leak Procedures Stop flow of material contain absorb small spills with dry sand earth and vermiculite Do not use combustible materials If possible carefully neutralize spilled electrolyte with soda ash sodium bicarbonate lime etc Wear acid resistant clothing boots gloves and face shield Do not allow discharge of unneutralized acid to sewer Acid must be managed in accordance with local state and federal requirements Consult state environmental agency and or federal EPA Handling Unless involved in recycling operations do not breach the casing or empty the contents of the battery There may be increasing risk of electric shock from strings of connected batteries Keep
39. maintenance The Turbo Start senses the impedance from the starter generator It then provides the exact power required throughout the start up curve 6 How many engine starts will my Turbo Start provide until it is depleted The Turbo Start back charges almost instantly once the vehicle aircraft is started and the generator is on line This power flywheel feature enables the Turbo Start to recharge itself right from the vehicle it started in less than 30 seconds You can go down the line in your motor pool and start every 24V vehicle without limit f How do you prolong the life of the Turbo Start s cells All you need to do is plug the unit in to the appropriate ac power outlet the system requires AC power will recharge the system and keep the cells healthy Users who regularly plug the system in can expect to get 5 7 years from their cells before they need to be replaced Tesla cells do not have a memory like cell phone batteries There is no need to fully discharge them The recharging system will not overcharge the unit or produce excess heat 8 Is it waterproof Water resistant but not waterproof See Environmental Section 113000 GPU 24 INV 1800 oo Toubleshooting amp raq 6 9 Are Tesla GPUs used in shop maintenance and testing Tesla systems are gaining popularity throughout maintenance facilities instructional facilities laboratories manufacturing plants aircraft hangars and many other lo
40. may also be used to establish local operating procedures and to ensure maximum usage of the unit f 2 General The data presented covers the maximum range of conditions and performance that can reasonably be expected In each area of performance the effects of temperature and dc electrical load demand relating to the ground power support requirements are presented Wherever practical data is presented conservatively However NO GENERAL CONSERVATISM HAS BEEN APPLIED All performance data presented is within the applicable limits of the unit f 3 Data Basis The type of data used is indicated at the bottom of each performance chart under DATA BASIS The applicable report and date of the data are also given The data provided generally are based on one of three categories A Derived From Actual Controlled Testing Controlled test data obtained on a similar unit type B Calculated Data Data based on tests but not on a similar unit type placed under a controlled test C Estimated Data Data based on estimates using rules of physics mathematics and electrical engineering principles and concepts but not verified by tests 1 4 Specific Conditions The data presented are accurate only for specific conditions listed under the title of each chart or graph Variables for which data are not presented but which may affect that phase of performance are discussed in associated text 5 General Conditions In addition to the specific c
41. ndustries Shipping Case 5 4 Storage If unit can not be connected to ac power while in storage we recommend to charge the unit once a year The shelf life of 12 months is due to the battery cells inside the unit We guarantee the unit will hold 80 of its charge for a period of 12 months without being recharged When the GPU s leave the facility they are fully charged and if they are to go into storage without being used they will maintain 80 of their charge after 12 months The units has a life expectancy of 5 to f years if maintained properly TI3000 GPU 24 INV 1800 29 Section 6 Troubleshooting and FAQ 6 1 Frequently Asked Questions 1 Why should buy a Tesla Turbo Start System Tesla Turbo Start is a multi functional system that are ideal for support of 24 Vdc vehicles and aircraft and their electronics avionics on the bench Tesla manufactures various systems of different sizes and capacities that are man portable maintenance free and provide pure dc power in a completely safe package Designed for Military applications these systems are equally valuable in maintenance support at the main facility or in remote locations They are easily transported and air portable They will also provide 28 5 Vdc when the system is connected to the appropriate ac source 2 How does a Turbo Start work The Turbo Start combines state of the art power conversion electronics with our proprietary dry cell batt
42. nmark NEMA 520P 40 113000 GPU 24 INV 1800 Optional Accessories 8 8 3 Cobra Replacement Contacts and Tools Cobra DC Plugs provide reliable high power connections up to 3000 amps even in the harshest conditions A rugged combination of advanced composite materials and corrosion resistant alloys make each plug maximized for durability and connectivity To extend the life of the Cobra Connector included with your unit replacement contacts posts noses and tools can be ordered through the Tesla Customer Service TI2005 238 Cobra Aviation Plug TI2005 078 Cobra NATO Connector NSN 6130 01 523 1270 CL IX 1 12004 444 i TI2005 251 gw 2005 654 a NATO Replacement Post DC Aviation Plug DC 400Hz Aviation Plug For newer NATO plugs with new style post indicated by the black Positive Negative Positive Negative tip Replacement plug uses standard 3 4 deep well socket for Contact Contact installation TI2005 121 TI2005 117 TI2005 250 2005 25 NATO Negative Contact NATO Positive Post DC Aviation Plug Aviation Insertion NSN 5999 01 525 0582 CLIX NSN 5935 01 523 8914 CL IX 3 slotted Connector Extraction Tool q 2005 426 as TI27000 082 A TI2004 341 TI2004 340 ne EREP TT EEE NEKENE NERE RE NATO Negative Contact NATO Positive Contact Replacement Nose f
43. onditions the following general conditions are applicable to the performance data A Variation in Aircraft Power demand differences between individual aircraft of the same make and model are known to exist due to variations in dc electrical system efficiency These differences however are considered insignificant and are not individually accounted for B Ground Support and Aircraft Instrument Variations The data shown in the performance charts do not account for instrument tolerance differences or inaccuracies 113000 GPU 24 INV 1800 Performance Data 7 7 6 Temperature Conversion Chart 6 49 6 0 74 2 72 4 0 6 68 8 67 0 65 2 63 4 61 6 595 58 0 56 2 54 4 52 6 50 8 49 0 47 2 45 4 43 6 41 8 40 0 38 2 36 4 34 6 32 8 31 0 29 2 27 4 25 6 23 8 22 0 20 2 18 4 2 0 26 0 25 0 24 0 23 0 22 0 21 0 20 0 19 0 18 0 17 0 16 0 15 0 14 0 13 0 12 0 11 0 10 0 16 6 14 8 13 0 11 2 9 4 6 5 8 4 0 2 2 0 4 1 4 3 2 5 0 42 8 44 6 46 4 48 2 50 0 51 8 53 6 55 4 57 2 59 0 60 8 62 6 64 4 66 2 68 0 69 8 11 6 13 4 5 2 7 0 18 8 80 6 82 4 84 2 86 0 87 8 89 6 91 4 93 2 95 0 96 8 98 6 100 4 39 0 40 0 41 0 42 0 43 0 44 0 45 0 46 0 47 0 48 0 49 0 50 0 51 0 52 0 53 0 54 0 55 0 56 0 57 0 58 0 59 0 102 2 104 0 105 8 107 6 109 4 111 2 113 0 114 8 116 6 118 4 120
44. or Replacement Nose for Insertion Extraction Tool Insertion Extraction Tool Aviation Plug Aviation Plug NSN 5120 01 523 8761 CL II NSN 5120 01 527 7729 CL Il 8 4 GPU Tires Tesla offers several tires in order to meet various customer mobility needs 1000 203 1 Run Flat Tire A solid foam rubber tire The stan dard tire for ground power units 21000 192 Balloon Tire For use on soft sand TI3000 GPU 24 INV 1800 41 COUNTRY Afghanistan Algeria American Samoa Angola Anguilla U K Antigua Argentina Aruba Australia Austria Azores Portugal Bahamas Bahrain Bangladesh Barbados Belgium Belize Br Hond Benin Bermuda Bolivia Botswana Brazil Bulgaria Burkina Faso Burma Now Myanmar Burundi Cambodia Cameroon Canada Canary Islands Spain Cape Verde Rep of Cayman Islands Central African Republic Chad Channel Islands Chile China Peoples Republic of Christmas Island Australia Cocos Islands Australia Columbia Congo Republic of Cook Island New Zealand Costa Rica Curacao Islands Cyprus Czech Republic of Denmark Djibouti Republic of Dominica Dominican Republic VOLTS 220 220 240 220 240 230 220 115 240 220 220 120 220 220 115 220 110 220 120 220 220 110 220 220 230 220 220 230 120 220 220 120 220 220 240 220 220 240 240 220 220 240 120 110 240 220 220 220 230 110 APPENDIX
45. quipment Indicates a condition operating procedure or practice which is essential to highlight 1 2 Symbols The following symbols will appear within the warning triangles to alert the user to the specific type of danger or hazard General Warning Electrical Hazard Explosion Hazard Fire Hazard Battery Warning Guard from Moisture Figure 1 2 1 Different types of hazard and caution symbols 113000 GPU 24 INV 1800 1 Safety Review 1 3 Hazards WARNING Severe injury or death from electrical shock may occur if either user or the unit is wet while the unit is connected to a power source If the unit has come into contact with water disconnect ac power from the ac source If AC Input Circuit Breaker has tripped due to water infiltration DO NOT try to reset it with the ac line voltage attached WARNING Severe injury or death from electrical shock can occur when damp electrical plugs are connected to the unit Before making any connections turn off unit Failure to use proper grounding can cause potential shock hazard In different countries the power cord may require the use of a plug adapter to achieve plug style compatibility for operation Use only adapters with proper grounding mechanism Figure 1 3 1 Proper Ground Figure 1 3 2 Proper Ground Figure 1 3 3 Improper Ground Grounded Plug with Grounding Pin Adapter with Grounding Mechanism Plug with No Grounding Pin Secured to Outlet CAUTI
46. r 3 16 Inverter Fan 3 17 Inverter Output Circuit Breaker 3 18 Disabling the GOHz 120 Vac Power Outlet WOWNR FR OOON N QI DP HF FA gt N 5 13 13 13 13 13 13 14 15 16 17 18 18 19 20 21 22 22 22 22 23 23 113000 GPU 24 INV 1800 3 19 GFCI Outlet Test and Reset Buttons 23 3 20 Pure Sine Wave Inverter Operating Limits 24 3 21 GOHz 120 Vac Power Outlet 24 3 22 Control Panel and LCD Display 25 3 23 Sine Wave Powersave Mode 25 Section 4 Post Operation 26 4 1 General 26 4 2 After Use 26 4 3 Power Cell Recharge 26 27 Section 5 Unit Care and Maintenance 28 5 1 Unit Care 28 5 2 Unit Servicing 29 5 3 Packaging and Shipping 29 5 5 Storage 29 Section 6 Troubleshooting and FAQ 30 6 1 Frequently Asked Questions 30 31 6 2 Basic USage Operation Questions 32 6 3 Basic Unit Troubleshooting 33 36 Section Performance Data 37 f 1 Purpose 37 f 2 General 31 f 3 Data Basis 31 1 4 Specific Conditions 31 7 5 General Conditions 37 1 6 Temperature Conversion Chart 38 Output Voltage 39 1 8 Maximum Output Current 39 Section 8 Optional Accessories 40 8 1 Shipping Case 40 8 2 Tesla AC Line Cords 40 8 3 Cobra Replacement Contacts and Tools 41 8 4 GPU Tires 41 Appendix A 42 46 Repair Request Form 4 113000 GPU 24 INV 1800 Abbreviations and Symbols Abbreviations that may be used within the text headings an
47. r GOHz 120 Vac Output TI3000 GPU 24 INV 1800 23 3 Operating Procedures 3 20 Pure Sine Wave Inverter Operating Limits At a full 15 amp load the ac output will be operational for approximately 32 minutes without ac power applied to the TI3000 GPU 24 INV 1800 When the unit s batteries drop to approximately 21 Volts the LCD display screen will begin to flash with the LOW BATT SHUTDOWN fault condition and an audible alarm will sound See Section 6 3 At this point the TI3000 GPU 24 INV 1800 s batteries will need to be recharged 3 21 6OHz 120 Vac Power Outlet Enabling the GOHz 120 Vac Power Outlet To activate the 60Hz 120 Vac Power Outlet first set the DC Input Circuit Breaker switch to the ON position see figure 3 21 1 This provides power directly from the power cells to the Pure Sine Wave Inverter Next set the AC DC Input Inverter Control switch to the position Initially the screen on the LCD Display will indicate the input voltage output voltage and frequency configuration Then the screen will display input voltage input current and output power see figure 3 21 2 Finally switch the AC Output Circuit Breaker to the ON position see figure 3 21 3 The 60Hz 120 Vac Power Outlet is now active Figure 3 21 1 GOHz AC Inverter Power Switch set to ON position Figure 3 21 2 Inverter Display Panel with Switch set to I ON position Figure 3 20 1 113000 GPU 24 INV 1800
48. rcuit Breaker is located directly below the AC Inverter Display See figure 3 19 2 When the circuit breaker has been tripped the LED will go out In the event the breaker trips 1 Disconnect any ac plugs 2 Wait for a minimum of 60 seconds 3 Reset breaker by switching off then on 4 Reconnect the ac plugs The Inverter Output should power up If the breaker continues to trip turn off the 6OHz AC Inverter Power switch and contact Tesla for further instructions 3 18 Disabling the GOHz 120 Vac Power Outlet When power is no longer needed make sure to turn off ac output circuit breaker the Inverter On Off switch and the DC Input Circuit Breaker This will ensure that the power cells are not drained unnecessarily 3 19 GFCI Outlet Test and Reset Buttons The inverter output is equipped with a GFCI outlet that will protect the user from potentially dangerous shocks due to faulty grounding see figure 3 19 1 Pressing the Test button will trip the outlet and break the circuit Pressing Reset will restore the circuit assuming no ground fault is present The green LED outlined in blue will illuminate when the receptacle is live In the event that the outlet does not work after resetting both the Inverter Output Circuit Breaker See figure 3 19 2 and the GFCI receptacle contact Tesla for further instructions Figure 3 19 1 6OHz 120 Vac Outlet Figure 3 19 2 Inverter Output Circuit with GFCI receptacle Breaker fo
49. rd T1I25000 005 United Kingdom Line Cord TI25000 002 Italian Line Cord TI25000 011 Australian Line Cord TI25000 011 Australian Line Cord TI25000 011 Australian Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 011 Australian Line Cord TI25000 001 North American Line Cord TI25000 001 North American Line Cord TI25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 300 Denmark Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord TI25000 001 North American Line Cord 113000 GPU 24 INV 1800 COUNTRY Ecuador Egypt El Salvador England Equatorial Guinea Estonia Ethiopia Fiji Finland France French Guiana Gabon Gambia Georgia Germany Ghana Gibraltar Greece Greenland Denmark Grenada Guadeloupe Guam Guatemala Guinea Guinea Bissau Guyana Haiti Honduras Hong Kong Hungary Iceland India Indonesia lran Ireland Republic of Isle of Man Israel Italy Ivory Coast Jamaica Japan Jordan Kenya Korea South Kuwait 113000 GPU 24 INV 1800 VOLTS 120 220 115 240 220 220 220 240 220 220 220 220 220 220 220 220 240 220 220 230 220 110 120 120 220 220 110 110 120 110 220 220 220 220 250 220 220 220 220 240 230 220 220 110 110 220 240 220 240 APPENDIX A Cont OPTIONAL LINE CORDS FOR WORLDWIDE OPERATIONS HZ 60
50. rips output Switch breaker to ON position C Reconnect unit to cables and run If LEDs still do not illuminate Please contact Tesla Customer Service at 302 324 8910 8 Unit does not put out 28 5 A Unit is not plugged in Plug unit into ac power source to volts dc power maintain 28 5 Stand alone Vdc is 24 Volts unplugged 9 Unit stand alone voltage is A Cells discharged Plug unit into ac power source less than 23 volts B Recheck capacity after 25 minutes Failure to hold above 23 Vdc Please contact Tesla Customer Service at 302 324 8910 10 Unit weakens after first A Weak cells Allow between 30 to 60 seconds start backcharge between uses Troubleshooting for the Pure Sine Wave Inverter is continued on the next page 113000 GPU 24 INV 1800 35 6 Troubleshooting amp FAQ The following fault conditions may be displayed on the Inverter Display Screen along with an audible alarm sound and a blinking LCD back light Inverter Display Indication HIGH BATT SHUTDOWN Battery Voltage too high Check for fault with battery charging system Fault Condition Manually reset Inverter by turning Off then On again LOW BATT SHUTDOWN Battery Voltage too low A Charge Batteries 21 Volts approximately Manually reset Inverter by turning Off then On again OVERLOAD SHUTDOWN A Battery current too high Reduce Load on Inverter Probable ac overload OVERTEMP SHUTDOW
51. rought up to 1800 RPM The dc circuit breaker of the inverter must be set to on The inverter power switch must be set to on 1 2 3 4 5 6 7 Engine Starting CAUTION The ac circuit breaker must be set to on Prior to engine start ensure power cell charge is sufficient to provide an efficient engine start Check dc power cable for secure and correct installation prior to engine starting Follow ground power engine starting procedure as specified in the aircraft or vehicle s operator manual CAUTION Removing DC Power Supply From Vehicle 1 Remove dc power cable GPU connector from vehicle 2 Remove dc power cable connector from TI3000 GPU 24 INV 1800 if necessary 3 Reinstall dc receptacle s protective cover 113000 GPU 24 INV 1800 3 12 Regulated AC Power Plugging in with AC Power When the TI3000 GPU 24 INV 1800 is plugged into ac power the output is 28 5 volts This voltage allows the system to recondition and recharge the vehicle s battery ies It is also an optimum voltage for powering avionics and lighting on most aircraft The GPU s ac to dc converter produces continuous amps of dc power depending on the size of the system CAUTION Connect AC Power Cord To Unit Ensure 120 or 240 Vac power cord is properly connected to an approved ac power supply After approximately 5 8 seconds unit s LED status indicator will illuminate indicating power cell state of charge Cooling fan will opera
52. s inspect cables prior to use If no damage is evident proceed to the next step If damage is evident contact Tesla Customer Service Do not attempt to use any other type of power cables other than the Tesla cables included with the unit 28 0 0 30006 244 4800 Unit Care and Maintenance 5 5 2 Unit Servicing This unit is a maintenance free sealed unit No repairs outside of Tesla are authorized Warranty will be voided if unit is tampered with in any way including any damage to the WARRANTY VOID stickers located on the case see Figure 5 2 1 below If the unit requires maintenance please contact Tesla Customer Service at 302 324 8910 A Repair Request Form can be found in the back of this manual Figure 5 2 1 Warranty Void stickers Front and Back on the unit 5 3 Packaging and Shipping Ensure proper packaging when returning the unit Transport the unit only in a sturdy shipping crate or Tesla Shipping Case It is important to enclose the Repair Request Form Seal the crate on all sides and return it to Tesla at the address listed below Please contact Tesla Customer Service at 302 324 8910 with any questions or concerns TESLA INDUSTRIES INCORPORATED 101 CENTERPOINT BLVD CENTERPOINT INDUSTRIAL PARK NEW CASTLE DELAWARE 19720 PHONE 302 324 8910 FAX 302 324 8912 Website www teslaind com Nzar Email Tesla1 teslaind com Figure 5 3 1 Tesla I
53. sh Line Cord T1I25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 004 Old British Line Cord TI25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord TI25000 001 North American Line Cord TI25000 011 Australian Line Cord TI25000 001 North American Line Cord TI25000 003 Continental European Line Cord TI25000 001 North American Line Cord TI25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord TI25000 003 Continental European Line Cord TI25000 003 Continental European Line Cord TI25000 005 United Kingdom Line Cord T1I25000 005 United Kingdom Line Cord APPENDIX A Cont UNIVERSAL LINE CORD KIT FOR WORLDWIDE OPERATIONS NOTE TESLA UNIVERSAL AC LINE CORD KIT P N TI25000 U00 IS FOR UNITS ORIGINALLY BUILT WITH THE UNIVERSAL AC LINE CORD OPTION ONLY THE AC ADAPTER OPTION IS TESLA P N TI1L6000 19 AND MUST BE ORDERED WITH THE ORIGINAL PROCUREMENT OF UNIT S UNIT S MAY BE RETURNED TO TESLA INDUSTRIES FOR A NOMINAL COST AND MODIFIED TO ALLOW OPERATION WITH THE UNIVERSAL AC LINE CORD KIT TESLA UNIVERSAL AC LINE CORD KIT P N TI25000 U00 IS COMPRISED OF THE FOLLOWING FIVE PART NUMBERS TI25000 111 NORTH AMERICAN LINE CORD TI25000 113 EUROPEAN 10A 250V TI25000 114 OLD BRITISH LINE CORD TI25000 115 ENGLAND 10A 250V TI7000 131 LINE CORD POUCH 113000 GPU 24 INV 1800
54. signed to provide 50 amps continuous at 24 volt dc output for aircraft engine starting and 24 or 28 5 volts dc output for ground maintenance avionics electrical troubleshooting and testing Another feature is the 1 800 Watt ac uninterruptible pure sine wave inverter with up to 15 amps continuous 60 Hz 120V power outlet This outlet makes it convenient to plug in laptops test instruments cell phone chargers and other electronic devices without using an alternate power source The observance of procedures limitations and performance criteria ensures peak operating efficiency and maximizes operational capabilities and life of the TI3G000 GPU 24 INV 1800 This manual contains the complete operating instructions and procedures for the TI3000 GPU 24 INV 1800 needed to safely and efficiently operate this GPU Figure 2 1 1 113000 GPU 24 INV 1800 2 2 Indication of Terms Shall Should and May Within this technical manual the word shall is used to indicate a mandatory requirement for proper operation and warranty purposes The word should is used to indicate a non mandatory but preferred method of accomplishment The word may is used to indicate an acceptable method of accomplishment 4 113000 GPU 24 INV 1800 AC Input Circuit Breaker Trips if over current fault condition occurs Push to Test Button Displays current battery charge state when pressed 24 Vdc Output Connector Provides 24 Vdc to 28 5 Vdc
55. splay Panel LCD on see figure 6 3 2 No Contact Tesla Industries Inc Yes Proceed to the next step Is the AC Output Circuit Breaker tripped see figure 6 3 3 No Proceed to the next step Yes Push the breaker in to reset Is the 6082 AC Power Outlet LED illuminated see figure 6 3 4 No Press the Reset button on the Outlet Yes Proceed to the next step Figure 6 3 3 60Hz AC Output Circuit Figure 6 3 4 60Hz AC Power Outlet ON Breaker push to reset green LED illuminated outlined in blue If the green LED on the front of the GOHz AC Power Outlet is illuminated the Outlet should be live If the LED does not light after pressing the Reset button contact Tesla Industries for further instructions 113000 GPU 24 INV 1800 33 _6 Troubleshooting amp FAQ Fault 1 Output Capacity LED does not come on when button is pushed 2 Unit has no output dc or ac input or both 3 Unit will not charge from ac outlet 4 Unit failed function test 5 Unit emits sparks when plugged into power source 6 Unit works then shuts down m o O U gt Possible Cause Units cells completely dead Units cells completely dead AC line cord is damaged or bad DC line cord is damaged or bad AC circuit breaker has been tripped Cables loose or corroded A AC line cord is damaged or bad Is ac line cord fully plugged into unit an
56. te Ensure LED status indicator and cooling fan is operational prior to continuing Figure 3 12 1 Connecting TI3000 GPU 24 Figure 3 12 2 AC North American Line Cord INV 1800 to AC Power Supply 3 13 Charging Unit Once you have the voltage selector switch set to match the power characteristics of your line cord you can plug the unit into a wall socket to charge the batteries When the LED status reads full charge see figure 2 11 2 plug the TI3000 GPU 24 INV 1800 into ac power to keep the cells charged whenever it is not in use even if it is at Full Charge The unit will not overcharge or overheat When the Unit is fully charged the LED indicator should show a single steady green bar The fan will run at reduced speed This is normal operation indicating the unit is in standby mode and is ready for use lf the GPU s cells need to be replaced After 60 minutes of ac power input the unit should be fully charged If the Push to Test button is pressed and the unit still indicates it is not fully charged then the cells should be replaced TI3000 GPU 24 INV 1800 21 Operating Procedures 3 14 Activating the Pure Sine Wave Inverter To activate the 1800 Watt Pure Sine Wave Inverter first press the DC Input Circuit Breaker to the ON position see figure 3 14 1 Next press the AC DC Input Inverter Control switch to the ON position Then oress the AC Output Circuit Breaker switch to the ON position This w
57. tions 1 What s the best position to place the unit for use vertical or horizontal Preferred position is horizontal for stability and airflow considerations When charging the preferred position is horizontal The Turbo Start can be put in any position while it is being used as there is nothing to spill inside the system 2 Does the unit have to be plugged in all the time No but for maximum performance and cell longevity keep the unit plugged in while not in use 3 What happens if don t keep it plugged in Unit will eventually lose its charge and cell life is shortened 4 How do check the status of the charge Press the Push to Test LED bar indicator on the unit s faceplate A fully charged unit will have one green LED light showing 5 Why is the cooling fan always running when am plugged into ac power Constant cooling fan operation ensures proper and consistent ventilation of the unit 6 Why does the cooling fan slow down Cooling fan rpm varies for better temperature regulation f Why does my LED flicker when the unit is plugged in Older Turbo Starts indicated a full charge with a flickering LED readout Newer models feature the illumination of one green bar on the LED readout when the unit is fully charged 8 What do do if a circuit breaker trips The AC Input Circuit Breaker is located above the AC Input Connector When the circuit breaker has been tripped either of the red but
58. tons will pop out In the event that the breaker trips 1 Disconnect the ac and dc connectors Unplug ac line cord on military unit 2 Wait fora minimum of 60 seconds 3 Reset breaker by pressing red button 4 Reconnect ac and dc connections to the unit Plugin ac line cord on military unit The unit should power up automatically If the breaker continues to trip return the unit to Tesla Industries for repair 113000 GPU 24 INV 1800 Troubleshooting amp FAQ 6 6 3 Basic Unit Troubleshooting When I plug my device into the 60Hz 120 Vac Power Outlet don t get any power The 6OHz 120 Vac Power Outlet produces voltage directly from the power cells Therefore the 120Vac Outlet should function regardless of whether the GPU is plugged in Before proceeding make sure the batteries have a sufficient charge If the Power Outlet is not on verify that the GOHz AC Inverter Power Switch is in the ON position The LED next to the Inverter Power Switch should be on see figure 6 3 1 Is the 60Hz AC Inverter Power Switch On LED illuminated No Turn on the 6QHz AC Inverter Power Switch Yes Proceed to the next step 6 3 1 6OHz AC Inverter Power set to 6 3 2 Inverter Display Panel and ON position LED illuminated On Off Switch turned on and active Is the Inverter On Off Switch in the I position see figure 6 3 2 No Turn on the Inverter On Off Switch Yes Proceed to the next step Is the Inverter Di
59. volves normal function test procedures and includes steps necessary to ensure that the 113000 GPU 24 INV 1800 operates within specified parameters prior to use A digital multimeter an example is shown in Figure 3 8 1 capable of measuring dc and ac voltage and resistance will be required to perform some of the tests These functional test procedures should become routine Figure 3 8 1 Digital Multimeter Check Unit for Evidence of Damage Check for dents punctures case distortion or misalignment and cracked or loose connectors If no damage is evident proceed to the next step If damage is evident contact Tesla Industries Inc Check DC Voltage Reading at DC Receptacle Terminals To verify that the power cells are fully charged set the digital multimeter to measure dc voltage As shown in Figure 3 8 2 place the positive probe red on the positive post of the DC Output Connector and the negative probe on the negative post The multimeter display should read approximately 28 5 Vdc 0 5 Vdc when power cells are fully charged and the unit is plugged into an appropriate ac power source When the unit is not plugged into an ac power source the multimeter display should read approximately 25 5 Vdc 160 TI3000 GPU 24 INV 1800 Operating Procedures 3 Check Unit Internal Resistance Test for Shorts Unit should be disconnected from any ac power sources prior to testing for shorts 2 Place the negative probe on the
60. with Inverter Activated Figure 3 21 3 AC Output Circuit Breaker with Power Switch set to ON position 24 TI3000 GPU 24 INV 1800 operating Procedures 3 3 22 Control Panel and LCD Display The Pure Sine Wave Inverter is equipped with a Control Panel that displays operational information so you can monitor the status of the inverter and the GPU s power cells A backlit LCD display shows both input voltage and current from the power cells Actual output power in watts from the inverter will be displayed when equipment is plugged into the power outlet In figure 3 22 1 the inverter has an input voltage of 25 0V with a current draw of 71A The resulting output power is displayed on an analog bar and reads 1500W Figure 3 22 1 When activated the power outlet will operate with or without NOTE ac power attached 3 23 Sine Wave Powersave Mode The Sine Wave Inverter has a built in Powersave mode to reduce the drain on the power cells when no load is present This mode when enabled checks the output for a load every 2 5 seconds and will automatically power up with a load of at least 10 watts To enable disable this feature set the Inverter Power Switch to O and then I When the PWR SAVE screen comes up quickly set the power switch to O wait three seconds and set the switch to I This will toggle the Powersave function on and off 113000 GPU 24 INV 1800 Section 4 Post

Download Pdf Manuals

Related Search

Related Contents

Garmin Auto Navigation Kit 010 10510 00  DELL OptiPlex 9020 MT  Compressor Cooler Pro  Leisure Time LX20 User's Manual  

Copyright © All rights reserved. Failed to retrieve file