4 in 1 Crib
Contents
1. WARNING LABEL SECTION 1 CRIB ASSEMBLY STEP 3 PARTS AND TOOLS REQUIRED TO COMPLETE STEP 4 ALLEN WRENCH eg lt SUPPLIED 525252552 MATTRESS SUPPORT x 1 P M6 x15 mm BOLT x 4 FROM STEP2 ATTACH THE MATTRESS SUPPORT PART K IN ALL CORNERS USING 1 M6x15 mm BOLT PART P IN EACH CORNER TIGHTEN WITH THE M4 ALLEN WRENCH THE A WARNINGS PRINTED ON THE POUCH ATTACHED TO THE MATTRESS SUPPORT MUST FACE UP THE SPRINGS MUST FACE UP THIS CRIB HAS 3 ADJUSTMENT POSITIONS USE THE HIGHEST ONLY FOR NEW BORNS MOVE THE MATTRESS DOWN AS THE CHILD GROWS A WARNING FALL HAZARD WHEN CHILD IS ABLE TO PULL TOA STANDING POSITION SET MATTRESS TO LOWEST POSITION AND REMOVE BUMPER PADS LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS STEPS FOR CLIMBING OUT N WARNINGS ON POUCH MUST FACE UP ALL CORNERS SECTION 1 CRIB ASSEMBLY PARTS AN2. SECTION 1 CRIB ASSEMBLY STEP 6 PARTS AND TOOLS REQUIRED TO COMPLETE STEP E ASSEMBLY INSTRUCTION OOKLET STORE THE ASSEMBLY INSTRUCTION BOOKLET IN THE POUCH ATTACHED TO THE MATTRESS SUPPORT STORE ALL PARTS AND TOOLS SEPARATELY IN A SAFE PLACE A WARNING SEE PAGE 2 FOR INFORMATION SECTION 2 TODDLER BED CONVERSION STEP 1 PARTS AND TOOLS REQUIRED TO COMPLETE STEP M4 ALLEN WRENCH SUPPLIED FINISHED CRIB REMOVE THE FRONT RAIL INSTALLED IN STEP 5 OF SECTION 1 CRIB ASSEMBLY SECTION 2 TODDLER BED CONVERSION STEP 2 PARTS AND TOOLS REQUIRED TO COMPLETE STEP M4 ALLEN WRENCH SUPPLIED DISASSEMBLE THE FRONT RAIL USING THE M4 ALLE
3. PRODUCT LABEL G LEFT CRIB END x 1 PART 21708 LEFT INSIDE BOTTOM LABEL B LEFT REAR LEG x 1 PART 21710 WARNING LABEL H RIGHT CRIB END x 1 PART 21709 PART 21711 RS E RIGHT FRONT LEG x 1 PART x A D LEFT FRONT LEG x 1 PART 21712 J STABILIZER BAR x 1 PART 21714 K MATTRESS SUPPORT x 1 PART 16945 POUCH ATTACHED TO MATTRESS SUPPORT KEEP INSTRUCTIONS IN THIS POUCH AFTER ASSEMBLY WARNINGS RELATED TO THE SAFE USE OF THIS CRIB ARE PRINTED ON THE POUCH 4 PARTS HARDWARE KIT IS PART 421715 FOR COLOR 204 OR 4 21717 FOR COLOR 100 SEE FRONT COVER KM L Mex 85 mm BOLT x 4 mn gt M M6x 60 mm BOLT x 6 Flat Head Screwdriver not supplied mp N M6 x 40 mm BOLT x 12 tp P M6x15 mm BOLT x 8 R M6x17mm BARREL NUT x 4 O S b4x30 mm METAL PIN x 6 M4 ALLEN WRENCH SUPPLIED SECTION 1 CRIB ASSEMBLY STEP 1 PARTS AND TOOLS REQUIRED TO COMPLETE STEP C RIGHT REAR LEG x 1 SQ A BACK RAIL x 1 X ES lt C R BARREL NUT x 4 M4 ALLEN WRENCH 0 SUPPLIED S 4 30 mm METAL PIN x 2 L M6x 85 mm BOLT x 4 B LEFT REAR LEG x 1
4. ATTACH 1 BACK RAIL PART A TO 1 LEFT REAR LEG PART B AND 1 RIGHT REAR LEG PART C USING 2 4x30 mm METAL PINS PART S 4 6 85 BOLTS PART L AND 4 BARREL NUTS PART R TIGHTEN WITH THE M4 ALLEN WRENCH USE THE FLAT HEAD SCREWDRIVER TO HOLD THE BARREL NUT IN THE PROPER ALIGNMENT SECTION 1 CRIB ASSEMBLY STEP 2 PARTS AND TOOLS REQUIRED TO COMPLETE STEP N 40 mm BOLT x 6 5 8 di 9 u U PRODUCT LABEL WARNING LABEL LEFT INSIDE BOTTOM LABEL H RIGHT CRIB M4 ALLEN WRENCH END x 1 SUPPLIED FROM STEP 1 3 LEFT CRIB END x 1 ATTACH 1 LEFT CRIB END PART G AND 1 RIGHT CRIB END PART H TO THE ASSEMBLY FROM STEP 1 USING 6 M6x40 mm BOLTS PART N TIGHTEN WITH THE M4 ALLEN WRENCH ECH PRODUCT LABEL LEFT INSIDE BOTTOM G LABEL
5. Read all instructions before assembly and use KEEP INSTRUCTIONS FOR FUTURE USE e a A ADULT ASSEMBLY REQUIRED Due to the presence of small parts during assembly keep out of reach of children until assembly is complete TM Children s Products 4 in 1 Crib THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE Consumer Care www DeltaChildren com Style Delta Children s Products Lot 114 West 26th Street D at e New York NY 10001 Tele 212 645 9033 REV FACTORY n When contacting Delta Consumer Care you will need to reference the above numbers They can also be ASTM F1169 10a Fl found on the label on the Crib End bottom rail CERTIFIED Safety Standards To register your product for important safety alerts and updates to your product please visit www DeltaChildren com and click on Product Registration OCTOBER 7 2011 21716 R6 2011 DELTA ENTERPRISE CORP ACAUTION ANY MATTRESS USED IN THIS CRIB SHALL BE AT LEAST 27 1 4 BY 51 5 8 IN WITHA THICKNESS NOT EXCEEDING 6 IN AWARNING Infants can suffocate on soft bedding Never add a pillow or comforter Never place
6. PART J USING 4 4x30mm METAL PINS PART S AND 6 M6x60mm BOLTS PART M AS SHOWN STORE ALL PARTS AND HARDWARE IN A SAFE PLACE SECTION 3 FULL SIZE BED CONVERSION STEP 2 PARTS AND TOOLS REQUIRED TO COMPLETE STEP ttp P M6x15 mm BOLT x 8 M4 ALLEN WRENCH FROM SECTION 3 STEP 1 SUPPLIED ATTACH BED FRAME TO THE HEADBOARD FROM SECTION STEP 1 AND FOOTBOARD FROM SECTION 3 STEP 1 USING 8 M6x15mm BOLTS PART P FOLLOW ALL INSTRUCTIONS SUPPLIED WITH THE BEDFRAME NOTE BED FRAME SYSTEM IS NOT INCLUDED SEE YOUR FURNITURE OR MATTRESS RETAILER CONTACT DELTA CHILDREN S PRODUCTS FOR INFORMATION OR WITH QUESTIONS NOTE SHOWN AS A FULL SIZE HEADBOARD AND FOOTBOARD NOT A
7. additional padding under an infant Failure to follow these warnings and the assembly instructions could result in serious injury or death DO NOT use this crib if you cannot exactly follow the accompanying instructions To reduce the risk of SIDS pediatricians recommend healthy infants be placed on their backs to sleep unless otherwise advised by your physician Strangulation Hazard STRINGS CAN CAUSE STRANGULATION Do not place items with a string around a child s neck such as hood strings or pacifier cords Do not suspend strings over a crib or attach strings to toys Strangulation Hazard To help prevent strangulation tighten all fasteners A child can trap parts of the body or clothing on loose fasteners Strangulation Hazard Do not place crib near window or patio door where cords from blinds or drapes may strangle a child Fall Hazard When child is able to pull to a standing position set mattress to lowest position and remove bumper pads large toys and other objects that could serve as steps for climbing out This crib has an adjustable mattress support For the convenience of the parent when the baby is very small the mattress support may be used in the highest position Important with the mattress support and mattress in the highest position be absolutely sure that the top of the front crib side is at least 3 inches higher then the top surface of the mattress If it is not lower the mattress support and the mattress to the ne
8. others safe by following these simple rules Do not allow any child to play on furniture Do not allow climbing on any piece of furniture Do not allow hanging from any piece of furniture Always monitor your child s activity when in the nursery NOTES ON CARE AND MAINTENANCE Do not scratch or chip the finish Inspect the product periodically contact delta children s products for replacement parts or questions Do not store the product or parts in extreme temperatures and conditions such as a hot attic or a damp cold basement These extremes can cause a loss of structural integrity To preserve the luster of the high quality finish on your product it is recommended to place a doily or felt pad under any items you place on the finish Clean with a damp cloth then a dry cloth to preserve the original luster and beauty of this fine finish Do not use abrasive chemicals Do not spray cleaners directly onto furniture Lift slightly when moving on carpeting to prevent leg breakage Use of a vaporizer near furniture will cause wood to swell and finish to peel PARTS MAKE SURE THAT ALL PRE ASSEMBLED PARTS ARE TIGHT C RIGHT REAR LEG x 1 A BACK RAIL x 1 PART 21706 F FRONT RAIL x 1 PART 21707
9. D TOOLS REQUIRED TO COMPLETE STEP F FRONT RAIL x 1 E RIGHT FRONT LEG x 1 O S 4 30 mm METAL PIN x 4 M4 ALLEN WRENCH SUPPLIED WD J STABILIZER BAR x 1 D LEFT FRONT LEG x 1 M M6 x 60 mm BOLT x 6 ATTACH 1 LEFT FRONT LEG PART D AND 1 RIGHT FRONT LEG PART E TO 1 FRONT RAIL PART F AND 1 STABILIZER BAR PART J USING 4 b4x30 mm METAL PINS PART S AND 6 M6x60mm BOLTS PART M TIGHTEN WITH THE ALLEN WRENCH SECTION 1 CRIB ASSEMBLY STEP 5 PARTS AND TOOLS REQUIRED TO COMPLETE STEP MM I N M6x 40 mm BOLT x 6 y M4 ALLEN WRENCH FROM STEP 3 FROM STEP 4 SUPPLIED ATTACH THE ASSEMBLY FROM STEP 4 TO THE ASSEMBLY FROM STEP 3 USING 6 M6x40 mm BOLTS PART N TIGHTEN WITH THE M4 ALLEN WRENCH a lol 2 lol 2 AY A
10. L HARDWARE SAFELY READ ALL WARNINGS ON PAGE 3 AS SHOWN USE AS A DAY BED OR LOVE SEAT SOFA DO NOT USE WITHOUT STABILIZER BAR INSTALLED N STABILIZER BAR MUST BE USED WHEN CONVERTED TOA TODDLER BED A TODDLER BED GUARDRAIL IS AVAILABLE FOR THIS CRIB PLEASE SEE YOUR CRIB RETAILER VISIT WWW DELTACHILDRENSPRODUCTS COM OR CONTACT DELTA CONSUMER CARE FOR MORE INFORMATION THIS CRIB USES DELTA STYLE 0080 GUARDRAIL SECTION 3 FULL SIZE BED CONVERSION STEP 1 PARTS AND TOOLS REQUIRED TO COMPLETE STEP M4 ALLEN WRENCH SUPPLIED YOU HAVE THE OPTION TO CONVERT THE CRIB TO A FULL SIZE BED SIMPLY FOLLOW STEPS IN REVERSE ORDER TO DISASSEMBLE THE CRIB THE HEAD BOARD IS THE BACK RAIL ASSEMBLY DONE THROUGH STEP 1 OF SECTION 1 TO CREATE THE FOOTBOARD ASSEMBLE THE LEFT FRONT LEG PART D RIGHT FRONT LEG PART E FRONT RAIL PART F AND STABILIZER BAR
11. LL BED FRAME SYSTEMS ALLOW USE OF A FOOTBOARD Children s Products Consumer Care www DeltaChildren com Delta Children s Products 114 West 26th Street New York NY 10001 Tele 212 645 9033 Warranty This Delta Crib is warranted to be free from defects for a period of 1 year from the date of purchase under normal use This warranty extends only to the original retail purchaser and is valid only when supplied with proof of purchase or if received as a gift when the registration is on file with Delta To register your product for important safety alerts and updates to your product please visit www DeltaChildren com Please do not return this item to the store before contacting us about missing parts or with any questions To report a problem please log on to www DeltaChildren comand click the Consumer Care Tab or contact us by phone at 212 645 9033 In the event that you need to contact our customer service department please have the Style Number and Lot Number available Use the space below to make note of those numbers They can be found on the label on the Crib End bottom rail STYLE No 7820 al REV FTY Lot No Pack Date Date of Purchase you should also keep your receipt
12. N WRENCH THEN ATTACH 1 STABILIZER BAR PART J TO 1 LEFT FRONT LEG PART D AND 1 RIGHT FRONT LEG PART E USING 2 4 30 mm METAL PINS PART S AND 2 M6x60mm BOLTS PART M TIGHTEN WITH THE M4 ALLEN WRENCH M4 ALLEN WRENCH SUPPLIED N M6 x 40 mm BOLT x 6 FROM SECTION 2 STEP 2 FROM SECTION 2 STEP 1 ATTACH THE ASSEMBLY FROM SECTION 2 STEP 2 TO THE ASSEMBLY FROM SECTION 2 STEP 1 USING 6 M6x40 mm BOLTS PART N TIGHTEN WITH THE M4 ALLEN WRENCH 9 D LLI gt lt o e LLI m D LLI Q Q O N Z O O LLI o PARTS AND TOOLS REQUIRED TO COMPLETE STEP SECTION 2 TODDLER BED CONVERSION STEP 4 A WARNING SEE PAGE 3 FOR TODDLER BED WARNINGS THE MATTRESS SUPPORT MUST BE IN THE LOWEST POSITION STORE AL
13. part of the sides of the crib Do not use this crib for a child who can climb out of it or who is taller than 90 cm TODDLER BED AWARNING INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT Openings in and between bed parts can entrap head and neck of a small child NEVER use bed with children younger than 15 months ALWAYS follow assembly instructions The maximum user weight is 50105 22 7kg AWARNING STRANGULATION HAZARD NEVER place bed near windows where cords from blinds or drapes may strangle a child NEVER suspend strings over a bed NEVER place items with a string cord or ribbon such as hood strings or pacifier cords around a child s neck These items may catch on bed parts A CAUTION ENTRAPMENT HAZARD To avoid dangerous gaps any mattress used in this bed shall be a full size crib mattress at least 51 5 8 in 1310mm in length 27 1 4 in 690mm in width and 4 in 100mm in thickness The mattress thickness must not exceed 6 in 150mm NOTES ON ASSEMBLY During the assembly process whenever using screws or bolts check each by placing the screw bolt on the diagram of the item which is drawn actual size and design Be sure to use the proper size and shape specified in the instructions To assemble this unit you may be required to place the unit on it s side and face It is strongly recommended that assembly is done on a soft non abrasive surface to avoid damaging the finish NOTES ON USE Keep children and
14. xt highest position Fall Hazard Stop using crib when child begins to climb out or reaches a height of 35in 89cm whichever occurs first The child should be placed in a youth or regular bed Check this product for damaged hardware loose joints loose bolts or other fasteners missing parts or sharp edges before and after assembly and frequently during use Securely tighten loose bolts and other fasteners Do not use crib if any parts are missing damaged or broken Contact Delta Children s Products for replacement parts and instructional literature if needed Do not substitute parts Follow warnings on all products in a crib If refinishing use a non toxic finish specified for children s products Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation Infants can suffocate gaps between crib sides and a mattress that is too small Ensure a safe environment for the child by checking regularly before placing the child in the crib that every component is properly and securely in place avoid head injury do not allow any child to play underneath the crib Never add an accessory such as a bassinet or changing table that extends over the sleeping area In Canada Only Use a crib mattress that is no thicker than 15 cm and is of such a size that when it is pushed firmly against any side of the crib it does not leave a gap of more than 3 cm between the mattress and any
Download Pdf Manuals
Related Search