User Manual
Contents
1. Nilfisk C 100 5 Nilfisk C 110 3 C 110 3 X TRA EN User Manual Index 1 Safety precautions and warnings 3 2 DeSO0Orplion ian inii 5 3 Before you start using your pressure washer 6 4 Operating your pressure washer 7 5 After using your pressure washer 9 6 Maintenance 10 TE TOM 12 8 Further information 13 9 lechnical CAND u EE 14 10 DN 14 1 Safety Precautions and Warnings Symbols used to mark in structions Do not let people who have not been trained in the use of a high pressure washer nor read the instruction manual operate the machine This appliance is not intended for use by children or other persons without assistance or supervision if their physical sensory or mental capabili ties prevent them from using it safely Children should be su pervised to ensure that they do not play with the appliance Before starting up your machine please check it carefully for any defects If you find any do not start up your machine and con tact your Nilfisk distributor Before starting up your high pressure washer for the first time this instruction manual must be read2. through carefully Save the instructions for later use Safety instructions marked with this symbol must be observed to pre vent danger to persons Especially check The insulation of the electric cable should be faultless and without any cracks If the electric cable is damaged an authorized Nilfisk distributor should replace it WARNING High pressure jets can be dangerous Never direct the water jet at persons pets live electrical equipment or the machine itself Never try to clean clothes or footwear on yourself or other persons Hold the spray lance firmly with both hands The spray lance is affected by a thrust of up to 16 4 N during ope This symbol is used to mark safety Instructions that must be ob served to prevent damage to the ma chine and its performance dicates tips and IS Instructions to simplify work and to ensure a safe operation This symbol in ration e The operator and anyone in the immediate vicinity of the site of cleaning should take action to protect themselves from being struck by debris dislodged during operation Wear goggles and protection clothes during operation e This appliance has been de signed for use with cleaning agents supplied or recom mended by the manufacturer The use of other cleaning agents or chemicals may adversely affect the safety of the appliance e Disconnect from electrical power supply before carrying out user mainte
3. 008 eee da et ed C 110 3 X TRA Nilfisk Advance A S Industrivej 1 DK 9560 Hadsund tel 45 7218 2100
4. alve can re duce pressure if it exceeds pre set values Locking device on spray gun 7a see illustration at the end of this manual The spray gun features a lock ing device When the pawl is activated the spray gun cannot be operated Thermal sensor thermal sensor protects the motor against overloading The machine will restart after a few minutes when the thermal sen sor has cooled 2 Description 2 1 Application 2 2 Operation elements and model survey IS This high pressure washer has been developed for domestic use within Car motorbike boat cara van trailer patio drive flags tones woodwork brickwork barbecue garden furniture lawn mower See illustration at the end of this manual Start stop switch Water inlet with filter 2a High pressure connection High pressure hose Electric cable Click amp Clean spray lance Spray gun with lock 7a Click amp Clean Tornado nozzle Click amp Clean Powerspeed nozzle D cO Only use the high pressure washer for purposes described in this manual The safety precautions must be observed to prevent damage to the machine the surface to be cleaned or severe personal Injuries 10 Foam sprayer 11 Nozzle cleaning tool 12 Lance and nozzle holder 13 Model tag 14 Holder for electric cable not standard on all models 15 Hexagon key Specifications See model tag 13 of machine We reserve
5. e it in a room without adequate ventila tion Note If the ma chine is left or not used for 5 min utes it must be switched off on the start stop switch O 1 1 Press the start stop switch O 2 Disconnect the electrical plug from the socket 3 Shut off the water supply and activate the trigger to relieve the machine of pressure 4 Lock the spray gun 7a When releasing the trigger of Always adjust the distance and thus the pressure of the nozzle to the surface which is to be cleaned the spray gun the machine automatically stops The ma chine will start again when you re activate the spray gun 5 After using your pressure washer EN 5 1 Storing the washer The machine should be sto 3 Stop the machine unplug red in a frost free room and wind up hose and cable 4 Place spray handle nozzles Pump hose and accessories and other accessories in the should always be emptied of holders of the machine water prior to storing as follows Should the machine by mistake 1 Stop the machine press the be frozen it will be necessary start stop switch O 1 and to check it for damage detach water hose and ac cessory NEVER START UP A FROZEN 2 Restart the machine and MACHINE activate the trigger Let the machine run until no more Frost damages are not water runs through the spray covered by the guarantee gun 5 2 Winding up of electric cable and high pressure hose To avoid accid
6. e ob served when connecting the high pressure washer to the electric installation The electric installation shall be made by a certified elec trician and comply with IEC 364 t is recommended that the electric supply to this appli ance should include either a residual current device that will interrupt the supply if the leakage current to earth ex ceeds 30 mA for 30 ms Water connection Connection to the public mains according to regula tions Inlet hose can be connected to the water mains with a max inlet pressure of 10 bars This high pres sure washer is only allowed to be connected with the drinking water mains when an appropriate backflow preventer has been Installed Type BA according to EN 1717 The backflow pre venter can be ordered under number 106411177 The length of the hose between the back flow preventer and the high pressure washer must be at least 10 metres to absorb pos sible pressure peaks min diam eter 1 2 inch Operation by suction for ex ample from a rainwater vessel is carried out without backflow preventer Recommended suc tion set 126411387 As soon as water has flown through the BA valve this water Is not considered to be drinking water any more IMPORTANT Only use wa ter without any impurities If there is a risk of running sands in the inlet water i e from your own well an additional filter should be mounted Safety devices e The unloader v
7. ect the nozzle 2 Clean the nozzle IMPOR TANT The cleaning tool 11 should only be used when the nozzle is detached 3 Flush the nozzle backwards with water 10 6 3 Cleaning of machine vents 6 4 Greasing of couplings The machine should be kept clean so as to let cooling air pass freely through the ma chine vents To ensure an easy connec tion and that o rings do not dry up the couplings should be greased regularly 11 EN 7 Trouble shooting To avoid unnecessary disappointments you should check the following before contacting the Nilfisk service organization Symptom Cause Recommended action Machine refuses to start Machine not plugged in Defective socket Fuse has blown Defective extension cable Fluctuating pressure Pump sucking air Valves dirty worn out or stuck Pump seals worn out Fuse has blown Incorrect mains voltage Machine stops Thermal sensor activated Nozzle partially blocked Fuse blows Fuse too small Machine pulsating Air in inlet hose pump Inadequate supply of mains water Nozzle partially blocked Water filter blocked Hose kinked Machine often starts and stops by itself Pump spray gun is leaking Machine starts but no water comes out frozen No water supply Water filter blocked Nozzle blocked Pump hoses or accessory Plug in machine Try another socket Replace fuse Switch off other machines Try without the extension cable Check that ho
8. ents the electric cable and the high pressure hose should always be winded carefully up around the handle C 110 3 C 110 3 X TRA Wind up the cable on the appropriate hook 5 3 Storage of accessories The spray handle lance and nozzles can be stored on the pressure washer EN 6 Maintenance 6 1 Cleaning of water inlet filter 6 2 Cleaning of nozzle WARNING Always discon nect the electrical plug from the socket prior to maintenance or cleaning To ensure a long and problem free working life please take the following advice e Wash out water hose high pressure hose spray lance and accessories before mounting e Clean the connectors of dust and sand e Rinse the detergent spraying attachment after use e Clean the nozzles Any repair should always be made in an authorized work Shop with original spare parts Clean the water inlet filter regularly once a month or more frequently according to use Carefully loosen the filter with a screwdriver and clean it Check that it is intact before re mount ing it The inlet filter must always be fitted inside the water inlet pipe to filter out sand limestone and other impurities as they will damage the pump valves CAUTION Failure to fit the filter will invalidate the guarantee clogging up in the nozzle causes a pump pressure which is too high This is why cleaning is required immediately 1 Stop the machine and dis conn
9. f the receipt must be enclosed Guarantee repairs are being made on the following condi tions e that defects are attributable to flaws or defects in materi als or workmanship wear and tear as well as misuse are not covered by the guarantee e that the directions of this instruction manual have been thoroughly observed e that repair has not been carried out or attempted by other than Nilfisk trained service staff e that only original accessories have been applied e that the product has not been exposed to abuse such as knocks bumps or frost As specified in European Direc tive 2002 96 EC on old electri cal and electronic appliances used electrical goods must be collected separately and recycled ecologically Contact your local authorities or your nearest dealer for further information e that only water without any impurities has been used e that the high pressure washer has not been used for rental nor used commer cially in any other way Repairs under this guarantee include replacement of defec tive parts exclusive of packing and postage carriage Besides we refer to your national law of sale The machine should be for warded to one of the service centres of the Nilfisk organisa tion with description specifica tion of the fault Repairs not covered by the guarantee conditions will be invoiced l e malfunctions due to Causes mentioned in section Troubleshooting Chart of the instruc
10. lean spray lance 6 Press the pawl to detach the Click amp Clean nozzle EN EN 4 3 Water connection IS 4 4 Start and stop of the machine An ordinary 1 2 garden hose of min 10 m and max 25 m will be suitable NOTE Connection to the public mains according to regulations The spray lance is affected by a thrust during operation therefore always hold it firmly with both hands IMPORTANT Point the nozzle at the ground Check that the machine is in uprigth position NOTE Do not place the ma chine in high grass 2 Release the trigger lock 7a 3 Activate the trigger of the spray gun and let the water run until all air has escaped from the water hose 4 Press the Start stop switch T 1 5 Activate the trigger of the spray gun IMPORTANT Only use wa ter without any impurities If there is a risk of running sands in the inlet water i e from your own well an additional filter 106411231 should be mounted 1 Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrat ing the machine Note Check that the filter is fitted in the water inlet pipe and that it is not clogged up 2 Connect the water hose to the water supply by means of the quick connector inlet water max pressure 10 bar max temperature 40 C 3 Turn on the water Do not cover the machine during operation or us
11. nance e To ensure the appliance safety only use original spare parts from the manufacturer or approved by the manufac turer e High pressure hoses fittings and couplings are important for the safety of the appli ance Only use hoses fittings and couplings recommended by the manufacturer e Do not use the appliance if a supply cord or impor tant parts of appliance are damaged e g safety device high pressure hose and trig ger gun e The appliance is intended to clean cars and garden etc e Appropriate ear protection has to be used e Never use the machine in an environment where there could be a danger of explo sion If any doubt arises please contact the local authorities e t is not allowed to clean as bestos containing surfaces with high pressure e This high pressure washer must not be used at tempera tures below 0 C WARNING Inadequate extension cables can be dangerous Cables on drums should always be com pletely unwinded to prevent the cable from overheating If an extension cable is used the plug and the socket must be waterproof and comply with the below mentioned requirements for length and cable dimen sions 1 0mm2 max 12 5m 1 5mm2 max 20 m 2 5mm2 max 30 m e f the electric cable is damaged it must be re placed by the manufacturer or his service agent or simi larly qualified person in order to avoid a hazard Mains power connection 9 The following should b
12. ses and connections are air tight Clean and replace or refer to local Nilfisk distributor Clean and replace or refer to local Nilfisk distributor Replace fuse Switch off other machines Check that the mains voltage corresponds to specification on the model tag Leave the washer for 5 minutes to cool down Clean the nozzle see section 6 2 Change to an installation higher than the amp consumption of the machine You may try without the extension cable Allow machine to run with open trigger until regular working pressure resumes Check that the water supply corresponds to specifications required see model tag NB Avoid using long thin hoses min 1 2 Clean the nozzle see section 6 2 Clean the filter see section 6 1 Straighten out hose Contact your nearest Nilfisk Service Centre Wait for pump hoses or accessory to thaw Connect inlet water Clean the filter see section 6 1 Clean the nozzle see section 6 2 In case problems other than the above occur please contact your local Nilfisk distributor 12 8 Further information 8 1 Recycling the washer 8 2 Warranty conditions Make the old cleaner unusable immediately 1 Unplug the cleaner and cut the electric cable Do not discard electrical appli ances with household waste Nilfisk guarantees high pres sure washers for domestic use for 2 years If your high pres sure washer or accessories are handed in for repair a copy o
13. the right to alter the specifications END 3 Before you start using your pressure washer 3 1 Mounting of trolley handle models with trol ley handle 3 2 Mounting of quick coupling 3 3 Mounting of high pres sure hose on spray gun 1 Place the trolley handle on the machine 2 Secure the handle by mount ing the 2 screws Use the enclosed hexagon key 1 Screw the quick coupling tight on to the water inlet 2 Note The inlet filter 2a must al ways be fitted in the water inlet pipe to filter out sand limestone and other impurities as these will damage the pump valves Caution Failure to fit the filter will invalidate the guarantee 1 Attach the high pressure hose 4 to the spray gun 7 Detach the high pressure hose by pressing the pawl A 4 Operating your pressure washer 1 Mount the high pressure hose on the outlet 3 4 1 Connection of high pres sure hose 4 2 Mounting of spray lance and Click amp Clean nozzles 1 Push the spray lance 6 into the spray gun 7 and screw it on Note The spray iss lance 6 has a built in low pres sure nozzle that can be used for flushing away dirt 2 Attach the nozzle Warning When attaching the Click amp Clean nozzles the pawl on the side of the spray lance 6 should come out again Note The foam sprayer 10 features a swivel lock which must be positioned in the hole in the Click amp C
14. tion manual 13 EN 9 Main Technical Data Tye C 100 5 5 C1103 5 C110 3 5 X TRA bar 70 7 0 75 7 5 max 110 11 0 max 110 11 0 52 230 240 230 240 4 0 15 10 0 015 1 0 0 15 10 0 015 1 0 0 15 10 0 015 1 0 78 78 Rated pressure bar Permissible pressure MPa max 100 10 0 CCC sax mater tempore bar Inlet pressure Sound pressure level dB A Guaranteed sound power level dB A ibration according to ISO 5349 m s 5 3 1 3 230 240 O CO 10 Declaratio Declaration Manufacturer s name and address or his Nilfisk Advance A S authorized representative in the Community Industrikvarteret 9560 Hadsund Denmark Name of the person responsible for the Anton S rensen General Manager of Technical Operations EAPC technical documentation Description of the equipment High pressure washer Equipment name Nilfisk Model C 100 5 5 C 110 3 5 C 110 3 5 X TRA Rated output voltage AC 230 240 V Rated frequency 50 Hz Measured sound pressure level 78 dB A Guaranteed sound power level 93 dB A Declaration The equipment refer in this document fulfils all the requirements of the Directive Machine Directive 2006 42 EC Low voltage Directive 2006 95 EEC EMC Directive 2004 108 EEC Outdoor Noise Directive 2000 14 EC EN ISO 12100 1 EN ISO 12100 2 EN 60335 2 79 EN 55014 1 2006 EN 55014 2 2001 EN 61000 3 2 2006 Place and date of the declaration Hadsund September 1 2
Download Pdf Manuals
Related Search